Search Documents

By Edgar L. Horner

"The objectives of the Wabush Mines tailings stabilization program are to control dust Ii/t-off and to rehabilitate the disposal area. The evolution of the program started with test plots in 1970, these being continued and expanded upon through 1974. In 1976, a 35-acre vegetation field trial was attempted and failed, part of the failure being attributed to lack of adequate equipment. Subsequently, equipment was purchased and during the summer of 1979-80 extensive areas were treated. The program was also expanded to include the evaluation of chemical and water spray stabilization versus vegetation in areas where shorter-term control is required. In addition, during the summers of 1979-80, spruce bog material was spread over about 100 acres and seeded.The approach to reclamation by vegetation at Wabush is one of soil building. Work to this point indicates that iron ore tailings can be converted to a soil capable of supporting plants. Plans for the Wabush tailings disposal area should make dust lift-off from inactive tailings areas negligible within the next few years."

Jan 1, 1981

By M. Timberlake, A. J. Jonaitis

"The DENVER Tube Press is a simple, high pressure (1500 PSI (100 bar)) filtration unit, developed for processing difficult-to-dewater materials and to produce a handleable filter cake and clear filtrate product.Lab and Pilot testwork conducted in Australia on coal fines (55-70% -35 micron (400 mesh)) have shown that total moisture contents of less than 20% are consistently achieved in the final cake products from the Tube Press.currently, these coal super fines are sent to waste due to uneconomical mechanical dewatering methods, which were only able to reduce total moisture levels in excess of 30%. Calculated, throughput rates for the 500 series Tube Press exceeded 1700 kg/hr (3750 lbs/hr). Feed solids concentration requirements are between 45 and 50% to achieve these results.INTRODUCTIONThe DENVER Tube Press is an automatic membrane high pressure filter press, which operates at hydraulic water pressures up to 1500 PSI (100 bar). The Tube Press was developed in the late 1960's by Charlestown Engineering, st. Austell, Cornwall, England, formerly a division of English China Clays, Ltd., to address more effective methods of moisture reduction of micron-size china clays. The Tube Press reduced moisture sufficiently to produce a hard surface-dry, handleable cake and clear filtrate discharge, which was recycled into the process. This development work was conducted using a 200 Series Tube Press (200 mm diameter x 2500 mm long filter surface)."

Jan 1, 1993

By H. M. Howard

"The subject of Grinding Media is perhaps still quite controversial. Many people will state today that the spherical ball is the only way, and also will state that this was settled long ago others are not so sure, and I am in this second category. Over the years there have been many changes in grinding and in our evaluation of grinding media we should always be ready to review the overall situation at regular intervals. There is quite a lot of inertia in all branches of Hineral Dressing and this is particularly true of grinding or, more correctly, comminution.In order to understand some of the things which are done today, and to understand some of the thinking on grinding, it is desirable to go back some sixty years and trace the developments in comminution. In doing this we should consider perhaps three general categories with respect to daily tonnage. An arbitrary division would be under 500 T.P.D., 500-5000 T.P.D., and large operations which might have several parallel units, each with a capacity of about 5000 T.P.D. For the future, in the broad picture, this last category will be the important one because we will be more and more dependent on large-tonnage low-grade operations for most of the metals of the future. Some such division is necessary because the daily tonnage will have a very great effect on what we can and cannot do. It is also necessary to consider the entire flowsheet, and to remember in particular that grinding is not merely to make small particles but is also a conditioning process, to prepare the materi.al for the process which follows. The relationship of crushing to grinding must also be considered. It is logical to include the liners as part of the grinding media and we should try to distinguish between the wear of grinding media and the consumption of media by corrosion. Finally, the whole question of grinding media should be examined in relation to the possibilities of using some form of autogenous grinding."

Jan 1, 1970

By R. F. Dawson, A. S. Bagnall, K. Barron

"At Smoky River Coal Limited (SRCL), economic occurrences of structurally thickened coal deposits form attractive surface mining targets. These steeply dipping, structurally complex deposits require that special attention be given to pit wall design and operational practices.Where anchor support is feasible, there is potential for reducing footwall waste requirements and/or increasing coal recovery. SRCL has used rock anchors to support footwall slopes since 1985. This paper outlines design considerations and performance of rock anchor support systems at SRCL.Three case histories are included that illustrate the design process for supporting steeply dipping footwall slopes using rock anchors.IntroductionWestern Canada contains vast reserves of high grade coking coal largely located in two belts within the Rocky Mountain Foothills straddling the Alberta/British Columbia border. There are about one billion tonnes of ""clean"" coking coal reserves (Romaniuk and Naidu, 1986) situated near existing mining infrastructure. Within the reserve areas shown in Figure I, a total of six producers operate 10 large mines linked with ports situated on Canada's west coast. Al! of the producers operate conventional shovel/truck surface pits.Surface mineable reserves within some of the mountain coal mines are located on dip slopes or where the geologic structure has thickened the coal near the surface, creating low strip ratio targets. Footwall slopes in these mines are developed parallel to bedding, thus minimizing waste extraction and preventing undercutting of potentially unstable strata. The base of the mineable coal measures in both north and south regions is marked by massive quartz sandstone units (Torrens Member and Moose Mountain Member) which often form the footwall. Footwalls developed within this basal sandstone unit can attain very high unbenched heights often with little risk of instability. In cases where the footwall is developed on weaker strata above this basal unit, stability considerations control slope height when bedding dips exceed about 30°. In these situations it is desirable to assess the benefits of artificial support to increase the unbenched footwall slope height."

Jan 1, 1995

By J. Gao

We present results from our investigation of the concept and practice of using surface-charged latex nanoparticles as building blocks for conductive membranes. Nanoparticles were synthesized by free-radical co-polymerization of two hydrophobic monomers, butyl acrylate (BA) and methyl methacrylate (MMA), a crosslinker, N, N'- methylenebisacrylamide (BIS), and a charged monomer, sulfonate styrene sodium salt (NaSS), in water. The resultant nanospheres were characterized with static and dynamic laser light scattering. Thin films were cast from concentrated particle dispersions, followed by incubation at ?110 °C. Conductivity, water uptake and final charge content were measured. The membranes have higher conductivities than both amorphous films cast from sulfonated BA-MMA-Styrene copolymer chains and BA-BIS-MMA-NaSS gel films. TEM images and neutron scattering spectra confirm the particulate structure of the membranes.

Jan 1, 2005

By R. F. Dawson, A. S. Bagnall, K. Barron

"At Smoky River Coal Limited (SRCL), economic occurrences of structurally thickened coal deposits form attractive surface mining targets. These steeply dipping, structurally complex deposits require that special attention be given to pit wall design and operational practices.Where anchor support is feasible, there is potential for reducing footwall waste requirements and/or increasing coal recovery. SRCL has used rock anchors to support footwall slopes since 1985. This paper outlines design considerations and performance of rock anchor support systems at SRCL.Three case histories are included that illustrate the design process for supporting steeply dipping footwall slopes using rock anchors.IntroductionWestern Canada contains vast reserves of high grade coking coal largely located in two belts within the Rocky Mountain Foothills straddling the Alberta/British Columbia border. There are about one billion tonnes of ""clean"" coking coal reserves (Romaniuk and Naidu, 1986) situated near existing mining infrastructure. Within the reserve areas shown in Figure I, a total of six producers operate 10 large mines linked with ports situated on Canada's west coast. Al! of the producers operate conventional shovel truck surface pits.Surface mineable reserves within some of the mountain coal mines are located on dip slopes or where the geologic structure has thickened the coal near the surface, creating low strip ratio targets. Footwall slopes in these mines are developed parallel to bedding, thus minimizing waste extraction and preventing undercutting of potentially unstable strata. The base of the mineable coal measures in both north and south regions is marked by massive quartz sandstone units (Torrens Member and Moose Mountain Member) which often form the footwall. Footwalls developed within this basal sandstone unit can attain very high unbenched heights often with little risk of instability. In cases where the footwall is developed on weaker strata above this basal unit, stability considerations control slope height when bedding dips exceed about 30°. In these situations it is desirable to assess the benefits of artificial support to increase the unbenched footwall slope height."

Jan 1, 1995

By S. Yue, P. Vo, M. Jahazi

The flow behaviour and microstructure development of a near-alpha titanium alloy during beta working has been investigated. Typical cogging conditions were simulated through compression testing of IMI834 at temperatures of 1025°C-1100°C, strain rates of 0.01 s-1 - 1 s-1 and post-deformation heat treatments up to 4h. Using a synthesis of available literature models, a finite element model has been developed and validated through quantitative measures of flow stress-strain data and beta grain characteristics. Flow behaviour was analyzed through a self-consistent method while the microstructure development was considered with regard to the kinetics of beta recrystallization. Deformation at beta or high alpha/beta working temperatures (T>l025°C) produced minor flow softening with complete grain refinement achieved through metadynamic recrystallization.

Jan 1, 2006

By Roland Hunt

This paper deals with the practical problems as sociated with blasting a heated pillar remnant. This pillar remnant was the final stage in the blasting of a multi-stag e pillar blast. Production from the previous stages had produced burning sulphide ore, resulting in high rock temperatures in the final unblasted stage. This is an account of how, under difficult conditions, the pillar remnant was blasted.

Jan 1, 1977

By Stephen Williams

This paper examines manning best practice in the Australian mining industry. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 15 open pit and 37 underground studies in Australia. The data was collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2008. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. Finally, the paper considers perspectives on best practice with regard to manning in the Australian mining industry and the limitations in application of this type of analysis in a global context.

May 1, 2009

By W. J. Kuit

"Complex facilities which provide for the collection, management and treatment of effluents emanating from the Sullivan mine and concentrator tailings were made operational in October, 1979. Key features of the system are the use of upgraded tailings ponds for the storage of up to 800 million litres of metals-contaminated effluents, a treatment plant employing lime in a high density sludge process and a sludge-impoundment facility designed for maximum long-term environmental safety. The completed works are cap1ble of satisfying a difficult range of operating requirements imposed by highly variable weather conditions, drainage flows and soluble metals loadi11gs. Final capital expenditures for the project will approach $10 million and annual operating costs are estimated at $0.8 million.This paper discusses the Kimberley effluents treatment project and the major considerations in its development. The treatment process, major plant equipment and initial operating experience are also described."

Jan 1, 1980

By Z. D. Hora

Sev_eral dozen si lica occurrences have been reported from various parts of Brit ish Columbia. Some represent hydrothermal veins or parts of pegmatite bodies; other are recrystall ized sandstones. Several vein type deposits were mined for smelter flux and as a source of white chips for stucco dash and simi lar products. Some quartzites were studied as potential sources of high-grade silica for ferrosilicon and silicon metal production. The province's only production of silica for ferrosilicon has come from a pegmatitic quartz plug near Oliver in southern British Columbia. Its reserves are now practically depleted.

Jan 1, 1984

By W. S. (Steve) Vaughan

The Origins of Joint Ventures in Canada?s Mining Industry ? Among the most important financing structures used in our mineral industry today ? Virtually unheard of in the Canadian industry prior to the 1970s ? Borrowed from the U.S. oil and gas sector where it came into prominence in the late 1930s ? The Securities Acts of 1933 and 1934 in effect killed the sale of (equity) shares for financing oil and gas wells and start up mining companies

May 1, 2013

The control of carbon concentration in a counter current carbon absorption circuit is critical to optimise gold recovery. MINTEK has developed a carbon movement controller to address this potentially problematic area in gold extraction. This controller reduces operator interaction by automating carbon movement. Elution schedules are entered into the control system, which then moves the carbon through the circuit into the first adsorption tank until enough carbon is available for elution. This is done while maintaining the specified carbon profile within the circuit. MINTEK has also developed an online-carbonconcentration- meter to measure carbon concentration in pulp. The meter uses an ultrasonic measurement technique. Long term testing has shown the measurement to be robust and require minimal maintenance. Results from a gold mine in South Africa’s well known Witwatersrand gold producing area has shown a decrease in soluble gold loss between 30 - 50% when the controller was used.

Jan 1, 2014

By K. J. Mintz

Conveyor belts installed in an underground mine can be a potential source of a major fire, thus the need for fife-retardant belting. A Canadian Standard, CAN/CSA-M422-M87, incorporating a small-scale flame test, a drum-friction test, a flame propagation test and an electrical surface-resistance test, has been developed to meet the varied needs of the mining industry. It is recommended that mines use Types A and B belting described in that Standard, because they will have passed the large-scale flame propagation test, rather than Type C, which does not require that test. Belting that has been approved by the U.S.A. Mine Safety and Health Administration (MSHA) may be much less fire-retardant than any Canadian approved belting.

Jan 1, 1992

"Classification is an important aspect of mineral processing plants and if not operated efficiently can compromise both the throughput and recovery of the circuit. This paper discusses the benefits that can be obtained by operating the classification section efficiently. Since classification in most of the mineral processing plants is carried out using either hydrocyclones or screens the case studies involving the two classifiers were used in the discussion. Studies where optimising the classification circuit lead to improvements in the performance of the overall plant were included to show the benefits of paying attention to this area that is usually neglected. The data from the mill-float mill float, SABC, and Single Stage SAG mill circuit case studies have shown that the circuit throughput can be increased throughputs without compromising recoveries by optimising the classification circuit. On plants where the ore can be liberated at coarser sizes the experimental results have shown that replacing hydrocyclones with high frequency screens can lead to improved plant throughput with no detrimental effect on recovery. The discussion has included information on design and operational considerations for plants that have or intend to use hydrocyclones or screens that could make the classification circuit more efficient.INTRODUCTIONComminution is the process in which particles are reduced in size mainly by crushing and grinding. In most mineral processing circuits comminution is carried out to liberate the valuable minerals prior to subjecting the ore to a recovery process were values are concentrated or extracted (Mainza, Evertsson, Benzer, Tavares, Powell, Rule, Plint, …, 2013). Comminution is an energy intensive process and is usually achieved in stages. It is common to have a classifier after each comminution stage. The process is carried out in stages to minimize energy usage and to improve the efficiency of the process in meeting product specifications. Although comminution circuits have been advancing classification has remained a key component of the comminution circuit design (Mainza et al., 2013). Mainza et al. (2013) summarised the role of classification in mineral processing circuit as: to allow material in the equipment that can promote high operational efficiency, to improve material handling in the circuit, to minimize overgrinding of material to reduce energy consumption, and to provide the best quality product to enter the next stage of processing. Classification stages are employed in comminution circuits to ensure that high throughputs are processed without compromising the product quality or to produce a fine product at relatively low energy. If neglected classification can have detrimental effects on plant performance."

Jan 1, 2016

By Q. Ricoux, F. Goettmann, A. Maihatchi

"Electrodeposition processes are widely used in the metallurgical industry to produce, extract and refine metals from various feed materials. However, raw materials used to provide non-ferrous metals often contain high amounts of iron. In the presence of iron, while metals are plated at the cathode, electrowinning processes produce corrosive and highly oxidative ferric ions at the anode that are harmful for the process sustainability. In fact, these ferric ions cause dramatic current efficiency loss, induce high maintenance expenditures to limit the corrosion of devices and it results in the formation of impure and dendritic deposits on the cathode. Consequently, the management of iron in electrodeposition process became a major issue in non-ferrous metals production. Actually, numerous methods have been developed to limit the ferric ion concentration in the electrolyte or, at least, to limit its harmful effect. Many methods aim to limit the iron(III) concentration in the electrolyte, generally by coupling electrowinning to extraction process such as solvent extraction (SX) (Bender & Emmerich, 2015), ion exchange (IX) (Gula, Dreisinger, & Horwitz, 1996) or cementation (Kust, 1979) processes to remove ferric ions. Other routes consist of (i) using the ferric ions oxidant properties to leach raw materials, either directly in the electrolytic cell (Fanta & Tributsch, 1975) or through a secondary circuit (Cain, 1950), or (ii) reducing ferric ions through periodic reversal of direct current to enhance the formation of Fe2+ (Loutfy & Bharucha, 1980). On the other side of the spectrum, papers discuss methods to valorize the iron from by-products of the non-ferrous metal industry, that generates vast quantities of iron containing wastes (A. Agrawal, Sahu, & Pandey, 2004). Many studies on iron electroplating and electrolytic iron production from ores have been carried out (Cain, 1950; Mostad, Rolseth, & Thonstad, 2008), but very few have been conducted on waste or by-products. Therefore, we propose to build on the previous literature review to develop a process for the production of electrolytic iron from by-products.INTRODUCTIONNon-ferrous metals and their alloys are used in a large variety of applications. Aluminum and titanium are used for their strength, light weight and corrosion resistant properties in structural applications. Copper has been used in various applications requiring high thermal and electrical conductivity, as kitchen products and electrical wires. Nickel and zinc are commonly used as plating materials; nickel offers a wide range of working temperature and zinc is used for steel plating. Gold, silver, and platinum group metals are used in electrical/electronic applications, jewelry and chemistry as catalysts."

Jan 1, 2016

By V. I. Peresypkin, A. Y. Lein, N. S. Bortnikov, Yu. A. Bogdanov

"Abstract - The lipid component in hydrothermal deposits of the Logachev vent field, at 14°45_N of the Mid-Atlantic Ridge (MAR) and Broken Spur vent field, at 29°N of the MAR, was studied. Biochemical, gas chromatographic (GS), and molecular mass methods (GC-MS) research established the mixed nature of the organic matter (OM) including phytoplanktonogenous, chemosynthesized lipids, and lipids of questionable origin. Specific local conditions around the sulfide ores of the black smokers (absence of free oxygen and presence of reduced copper, which prevents OM degradation) facilitate the preservation of biogenic material, including bacteria. The main differences between the lipid compositions of the hydrothermal deposits of these two vent fields relate to the variable nature of hydrothermal circulation systems.At the 14°45_N vent field, high-temperature hydrothermal fields are forming due to the reaction of sea water with upper mantle ultrabasic rocks during serpentinization (a deep hydrothermal circulation system). High pressure and temperature (>400°C), a reducing environment and the presence of various metal oxides are favorable for the abiogenic synthesis of CH4 and oil hydrocarbons (HC). At the Broken Spur vent field, hydrothermal deposits are forming above axial crust magma chambers due to the interaction of sea water and basalts (an axial hydrothermal circulation system). Abiogenic synthesis of HC also occurs in this situation, but to a considerably lesser extent."

Jan 1, 1999

By X. J. Guo, Q. K. Wang, S. P. Zhong

With depletion of traditional clean copper reserves and fast expansion of the global copper demand and smelting capacity in the past decade, more and more copper smelters have to treat copper concentrate with increasing content of complex arsenic-bearing minerals. Developing economically viable and environmentally reliable methods and approaches for arsenic control in copper smelting has become more critical for sustainable growth of the copper industry. This paper will report the recent effort of Zijin Mining Group Ltd. in developing processes for improving arsenic control and management in the Zijin Copper Smelter. The arsenic distribution and balance data for matte smelting, converting and refining operations in Zijin Copper Smelter is reviewed for understanding of the current challenges in arsenic control. The processes developed for treating the arsenic bearing waste acid bleed stream from the smelting-converting off-gases wet cleaning circuit and the arsenic sludge produced in the refining electrolyte purification circuit for arsenic disposal are discussed. INTRODUCTION With fast expansion of the global copper smelting capacity to meet the world copper demand and depletion of traditional clean copper reserves, more and more copper smelters have to treat copper concentrate with an increasing content of complex arsenic-bearing minerals. China is the world largest copper consumer and also has the largest copper smelting and refining capacity, but majority of its smelting capacity relies on supply of imported copper concentrate. In order to meet the increasing copper demand and ease the tight supply of clean copper concentrate, the Chinese copper industry has to look at the domestic opportunity of developing non-traditional copper resources, specifically those of lower grades, more complex mineralogy, and increasing level of deleterious elements especially arsenic and also process imported copper concentrate with increased arsenic content. Due to a significant and growing environmental issue associated with arsenic contamination, developing economically viable and environmentally reliable methods and approaches for arsenic management and control in unlocking the maximum value of such arsenic bearing copper resources has become more critical for sustainable growth of the industry.

Jan 1, 2019

By S. Perkins, E. Young, L. Dufour, K. McVey, L. Rolandi

This paper presents a review of plant layout considerations incorporated into recent designs of SAG/Ball mill circuits for two medium sized concentrators. The plant layouts presented and the design concepts discussed, relate to smaller SAG circuits, but can equally apply to larger milling circuits. Included are design concepts and ideas introduced by the various project teams, and the focus is on the primary factors of any layout design which are safety, constructability, operability, and capital cost.

Jan 1, 2012

By Brian Hall

For some years, the mining industry has been consistently delivering returns below the market average. One of the causes is a disconnect between what is perceived to drive value creation by many industry analysts and senior corporate executives, and what actually drives the intrinsic value of mining operations. The perverse effect is that strategies that should increase value are perceived to have the potential to drive share prices down, and vice versa. This paper challenges common perceptions of what drives a mining company?s value. Anecdotal evidence suggests that the key drivers of value in the market, and hence in many boardrooms, are such things as increasing the reserves and production rate, and reducing unit operating cost. However, while the quoted reserves may satisfy ore reserves reporting code requirements to be economic, this does not imply that they are optimal. Often, a proportion of the quoted reserve reduces the potential value of the operation. Metal price increases, increased production rates, and operating cost reductions are all seen as conditions or actions that can improve value, and lead to cutoff grade reductions, thereby increasing ore reserves. However, modern cutoff theory and studies conducted by the author and his colleagues show clearly that, while breakeven cutoff grades will fall in these circumstances, optimum cutoffs may be much less volatile, and may even increase. Results from case studies indicate that value is maximised by right-sizing, not maximising, the production capacities, and by optimising the cutoff strategy. Values of many existing underground mining operations can be increased significantly by a substantial cutoff grade increase. Also, an increase in downside risk, and hence reduced returns, can occur using typical life-of-mine planning strategies if prices received are lower than predicted. Since this is often the case, low industry returns may be a direct result of typical strategic mine planning processes. Relatively simple cost-effective techniques are available to provide senior decision makers with information needed to assess the tradeoffs between their many conflicting corporate goals, and the balance between risk and reward. Often this information is not being generated at all. If it is, decisions affecting the value of the company are occurring by default at relatively low levels within the hierarchy, with senior executives apparently unaware of them or their potential impact. The paper concludes that without a re-evaluation of the way mining projects are valued, to demand proven value optimisation from mining plans by boards and mining analysts, the industry will continue to deliver below average returns.

May 1, 2003