Search Documents

By M. du Plessis, G. More O’Ferrall, A. Hartzenberg

"Lonmin Platinum has experienced several cases of large-scale hangingwall instabilities during the extraction of the Upper Group 2 Chromitite Layer (UG2) at a number of the Marikana operations along the Western Limb of the Bushveld Complex. These instabilities were all attributed to the presence and interaction of prominent geological features and highlighted that assumptions made in the design of the stable pillars and stable span were potentially overly simplistic in these areas. Investigations into the various case studies over the past ten years have resulted in the identification and classification of the rock mass characteristics of the geological structures causing the instabilities.In order to get a better understanding of these instabilities, it is important to understand the structural geology in general, and the sequence of events that led to the formation of the Bushveld Complex in particular. The tectonics involved in the formation of the various layers around the economic mineralized layers has been investigated, and the influence of these tectonic events on the stability of the UG2 stopes hypothesized.Following this investigation, the behaviour of the various layers in the hangingwall of the UG2 is better understood. This paper presents a description of the ground conditions being experienced in the underground stoping environment, the possible source of the associated structures and the resultant behavioural mechanism of these structures causing the rock mass instabilities."

Jan 1, 2015

By G. Landry

"IntroductionThe Cape Breton Development Corporation (CBDC) is constantly searching for new technologies that will enhance the marketability of its coal. One technology which shows promise in utilizing Cape Breton coal while at the same time addressing the traditional problem of high sulphur inherent in the Sydney coalfield, is coal-water fuel (CWF).The CWF process incorporates a physical change of coal by grinding it to a flour-like consistency and then mixing additives with it to make a fine coal slurry. The result is a liquid dispersion of fine coal particles that looks like oil, stores and flows like oil but burns like coal. The equipment used in the CWF process is standard mineral processing equipment but application of the equipment to manufacture a specific coal particle size and the specified additives used in the mixing make it a unique technology.The product, which CBDC calls Carbofuel, consists of 70% coal, 29.5% water and 0.5% chemical additives. The key properties of the product are: (I) high solids loading, (2) medium viscosity levels, (3) stability against sedimentation, and (4) good atomization behaviour. Carbofuel specifications are presented in Table I. Carbofuel ProductionThe production of Carbofuel is based on the controlled processing of coal. This involves wet grinding of the coal to a specified fine size (-250 um), cleaning this fine product to remove mineral impurities and formulating (with chemical additives) a finalproduct from the cleaned coal. The flow diagram in Figure 1 indicates the processing circuit for Carbofuel production.CBDC operates a 7-tonne-per-hour continuous production plant complete with state-of-the-art control, full laboratory services, product storage and loadout facilities. The plant has operated since 1983 and has produced over 12000 tonnes for several major demonstrations. The plant is shown in Figure 2."

Jan 1, 1987

By E. H. Henderson

MR. R. V. NEILY stated that he had at one time operated at Goldenville. The practice and results are much the same now as in the olden days. Inside plates were then found to be a source of trouble and had been removed. At the Libbey mine, Queen's county, the sulphides carried considerable gold, and $45.00 to $60.00 per ton had been recovered from the concentrates by roasting and chlorinating. Later, concentrates were treated with bromocyanide. Following that practice, a cyanide leaching plant was installed, which did not require concentration of the tailings. Cyanidation brought a recovery of around 95 per cent, with but $300 worth of plant. In Nova Scotia, the ore of each locality presents an individual problem of its own as to treatment required. Ma. W. B. Timm stated that, in the majority of Nova Scotia gold ores, more than 75 per cent of the gold content is free-milling and, naturally, stamps are most efficient for collecting and amalgamating this gold. In Ontario and the West, they had got away from stamps, and perhaps the main reason was that the supply of battery-men, who came from Nova Scotia, had died off. Ball-mills had been installed, which required smaller space and handled large tonnage, even though, as far as amalgamation goes, the stamps were probably more efficient. If concentration is to be done, ore from stamps is usually in better shape for recovery in passing over the tables, as there is no slime. With the ball-mill, flotation is necessary. The better practice, undoubtedly, is to take out what gold is possible before it is all smashed up, as in the ball-mill, though recent developments in the ball-mill make it possible to trap and take coarse gold directly from the mill. In this way, cyanidation is speeded-up, due to saving of the time the coarse gold would take before going into solution. PROFESSOR A. E. FLYNN found it unusual in these days to read anything in favour of the stamp mill, and thanked Mr. Henderson for the excellent paper in which he upholds the stamps and backs his opinion with facts from actual operations. For the typical Nova Scotia ore, containing coarse gold, stamps are un¬excelled. It used to be said that the virtue of stamps is that they brighten the gold for amalgamation. Although this saying is almost classical, it is not true, for gold is never brighter than in the native, untouched state. Any hammering that gold gets makes it more difficult to amalgamate.

Jan 1, 1935

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By Ryan W. Siggelkow

Mines today use various methods of mining to extract ore. Because of the dangerous nature of many of these processes, remotely controlled LHD machines are being used to extract the ore from the draw point. The remote control system, although being made safer all the time, has remained virtually unchanged for many years. The basic functionality is an operator switching the machine to remote control, getting out of the cab, walking up a stand, operating remotely, returning to the cab, switching to manual, driving manually, switching to remote, and switching to manual. It seems repetitive, and time consuming, does it not? Networking, convergence, video, voice, and data infrastructures, and other technologies are growing by leaps and bounds in virtually every industry and region, except for mining. From the comfort of the living room couch, a Canadian can play hockey online with full voice conversations over the Internet with someone in Russia in real time. Yet, a mine superintendent must jump through hoops to have a private conversation with the front line supervisor underground. "Is Joe around anywhere?" If Joe hears the message, he will respond. If not, who knows? Maybe he's hurt. Maybe he's not. Where is Joe? Nobody really knows, and that is scary. Today, surface knows that the workers disappeared into the cage at 7:00 a.m. They also know that the workers will probably and hopefully return at 3:00 p.m. Is there not a better way to handle this? With such a complex industry, it seems as if, for the most part, the introduction of new technology into mining has either been overlooked or has been met with some resistance. It is time to step back, look at the process, and see how it can be improved. Key areas of focus will be safety, productivity, dependability, and cost-effectiveness.

May 1, 2010

By A. C. Hitchins, C. N. Orssich

The Eagle zone is a gold-bearing, sheeted, quartz vein porphyry deposit hosted by the Cretaceous Dublin Gulch biotite granodiorite stock, located in central Yukon, 50 km north of Mayo. The deposit occurs at the western end of the stock and has been drill tested over a 1000 m by 500 m area, to a depth of 150m. Mineralization consists of 1 cm to 2 Cm wide, parallel, grey and white quartz veins with accessory gold, arsenopyrite, pyrite, pyrrhotite, chalcopyrite, native bismuth, bismuthinite, and scheelite. Vein densities range from two to fifteen veins per metre and average approximately five per metre. The majority of the veins have potassic and or phyllic alteration envelopes. Alteration of the granodiorite becomes pervasive as vein densities increase. Mineralization outside of the Eagle zone, but spatially related to the Dublin Gulch stock, includes: (i) scheelite bearing sheeted quartz vein zones within the east-central portion of the stock; (ii) a swarm of gold-bearing quartz-sulphide veins up to a metre wide in a zone along the northern contact of the stock and extending 7 km further west; (iii) the Mar scheelite skarn located on the south side of the stock; and (iv) cassiterite-bearing breccias located 2 km north of the stock. A geological potential resource of 64.5 Mt tonnes at a grade of 1.03 g/t Au has been estimated for the Eagle zone from widely spaced core and reverse circulation drill holes. Mineralization is open at depth, on strike to the west and beneath the hornfels to the north.

Jan 1, 1995

By K. D. Bulin

"An interesting brief history review of shovels as the primary excavating tool will permit the reader to see that immeasurable development and resources have preceded the shovel excavators which today are used extensively throughout the mining industry. With this as a background, the shovel manufacturer has the ability to utilize his resources best in those areas of shovel development in which the maximum benefits of increased reliability, performance and ease of maintenance will improve the operating rewards to the user of the equipment. The author explains the function of the shovel as a part of the material handling system. A detailed description of those areas of the shovel in which the most recent developments and major improvements have been implemented in the manufacture of the shovel excavator arc included."

Jan 1, 1973

By Masashige Makifuchi, Hiroki Kumakura, Kota Nagai, Takahiro Kikuchi

"A large amount of platinum group metals (PGM) are used in automobile catalyst. It is important to recover the metals from wasted catalyst. Nomura and Kageyama (2013) suggested recovery process that PGM oxides were absorbed to perovskite-type oxide based on LaScO3. In their process, the PGM in wasted catalyst as absorbed to the perovskite-type oxide as PGM oxide. It has potential to each element in the process if the perovskite-type oxide is selected properly. In this study, the PGM oxide absorption properties of various perovskite-type oxides are investigated to develop a new recovery and separation process. The various perovskite-type oxide were synthesized with metallic platinum, palladium, rhodium at high temperature in air atmosphere. And the PGM contents in the perovskite-type oxide after the experiment are determined by chemical analysis. Some of them have the properties to absorb specific PGM oxide selectively. In addition, in order to increase the amount of absorption of PGM oxide and composition of the perovskite-type oxide experimental temperature was investigated. Then it is also found that doping another specific element to the perovskite-type oxide is effective to increase the amount of absorption of PGM oxide. Then a new recovery process of PGM from wasted automobile catalyst, in which PGM can be separate to each element, was designed.INTRODUCTIONA large amount of Platinum (Pt), Palladium (Pd), and Rhodium (Rh) are used in automobile catalysis (Figure 1) (Platinum, 2013). Natural supplies for these metals are limited and PGM mining can detrimental environmental impact. Therefore, the recycling of PGMs from wasted automobile catalysis is very important. The Rose process (Figure 2) was developed as a process to recover PGM from wasted automobile catalysis. In this process, the automobile catalysis is first crushed mechanically, and then extracting agent, copper (Cu), and flux are melted at high temperature. The mixture separates into a metal phase, (Cu alloy containing PGM) and slag. The PGM is enriched by oxidizing. Cu to Cu oxide. The PGM are then recovered and separated to each element in a wet process. However, it is hard to dissolve the PGM with acid because they are chemically stable and strong oxidation agent such as aqua regia is used. Moreover, to separate the PGM to each individual element, a solvent extraction process is required."

Jan 1, 2016

By G. J. Desroches

"In order to improve zinc plant productivity, areas of low efficiency were identified. As a result, solution purification was improved, additional dust precipitator capacity was made available and a new zinc casting plant was installed. The effects of these and other changes are discussed and the expenditure and benefits reviewed. HistoryThe operation of the Flin Flon metallurgical complex including an electrolytic zinc plant commenced in October 1930. The design of the zinc plant was based on that of the Commonwealth Mining and Smelting Company at Trail, British Columbia, the Anaconda Great Falls Montana Plant and the Electrolytic Zinc Company plant at Risdon, Tasmania.The plant began with a design capacity of 60 tons per day and currently produces 255 tons per day. Since plant start-up, approximately 3.5 million ton s of zinc metal have been produced, most of it exceeding special high-grade specifications.IntroductionThe facility incorporates the basic process steps of roasting, leaching, purification, electrowinning and casting. Figure I details the flowsheet. During the late 1970s, management recognized that in order for the zinc plant to continue operating, it was necessary to introduce cost-effective practices.Study groups, consisting of design engineers and operations personnel, were formed to investigate the details of plant revisions.The objectives were to improve productivity by reducing manual labour, reducing energy usage, increasing zinc recovery, increasing metal output and reducing costs.This paper details the changes made during the period 1979to 1986 and shows how these changes have affected the productivity and economics of the zinc plant operation."

Jan 1, 1988

By J. R. Bradfield

THOSE familiar with the development of the Horne mine can readily appreciate that more and more accommodation bas been required for underground labour as the mine has grown. A permanent fire-proof change house, 30ft. by 75 ft., was built in 1927 to accommodate 194 men. This was extended ro 30 ft. by 92 ft. in 1928 to accommodate 296 men, and to 30ft. by 110 ft. in 1930 to accommodate 398 men. By 1933 this building was again overcrowded and tentative plans for a new change house were drawn up. However, it was realized that future operations would be centred around No. 4 shaft and a proposed new shaft, and the decision as to the location of the new change house had to be deferred until the area which seemed most suitable for the new shaft had been thoroughly explored underground. In the spring of 1934, the basic idea was accepted of drying the wet clothes in open mesh compartments or baskets located between rows of standard steel street-clothes lockers and built so that the covers or lids would serve as seats or benches.

Jan 1, 1935

By M. Leroux, C. J. Martin, S. R. Rao, J. A. Finch

"The effect of nitrogen on the flotation separation of sulphides from complex ores from Brunswick Mining and Smelting (New Brunswick) and Mattabi Mines (Ontario) was investigated. The most significant finding was enhanced pyrite floatability after as little as 3 minutes nitrogen conditioning. This was used in a novel sphalerite/pyrite separation process developed on the Brunswick ore. After aeration and Cu/Pb bulk flotation in air using xanthate the slurry was nitrogen conditioned, xanthate added and the pyrite floated in nitrogen. As an example up to 70% pyrite recovery with about 20% sphalerite recovery was achieved. Sphalerite was recovered from the pyrite tailings and the pyrite concentrate by copper-activation, raising the pH to 10 and floating in air. About 65-70% recovery at 35-40% Zn grade was achieved compared to 25% Zn grade by the conventional route. The process offers a promising alternative to current practice which seeks to depress pyrite at all stages. A possible mechanism of the effect of nitrogen is presented. INTRODUCTIONUse of gases other than air in froth flotation has been reported from time to time. [Podobnik and Shirley, 1982; Lin and Metzer, 1975]. Of all the gases, nitrogen would appear to hold the greatest practical promise because of its easy availability and chemical inertness. It is used in froth flotation in chalcopyrite-molybdenite separation [Redfearn, 1983]. The use of nitrogen in polysulphide chalcopyrite. this case is mainly to reduce the oxidation of a compound (Nokes reagent) used as a depressant for There is no reported use of nitrogen in the flotation of other sulphide minerals."

Jan 1, 1988

By G. P. Gormley

"Future open pit metallurgical coal mines in western Canada will be developed in complex geological environments. The success of these operations will be influenced by the mine operators' ability to prepare accurate mine plans and to predict and, subsequently, 10 control both out-of-seam dilution and coal recovery. Quintette Coal Limited has been mining its tightly folded and severely faulted Mesa depo sit at annual rates of up to 9 Mt of raw coal, since October 1982. Ongoing development drilling combined with continuous utilization of blast hole information, has been required to achieve an acceptable geological data base for short range mine planning. Thrust faulting has been a primary geological cause of difficulty in selectively mining waste and coal, which has resulted in higher than expected dilution in plant feed. The same geological phenomenon has also increased reserves by 6.3% and allowed for expanded mine plans to include a lower thrust plate, ultimately doubling the mines original reserve base. This paper illustrates the geology of the Mesa deposit and the type of work involved in its interpretation. Regional GeologyThe Quintette Coal Limited (QCL) property is located in the Peace River Coal Field of northeastern British Columbia. In this area, northwesterly-trending folds of the Rocky Mountain foothills are commonly cut by multiple, low-angle thrust faults, which dip to the southwest. The Lower Cretaceous Gates Formation, of near shore continental origin, contains 5 to 7 mineable seams of medium volatile bituminous metallurgical coal (Figs. I and 2). These seams normally range in thickness between 0.75 m and 9.5 m and have an aggregate thickness of between 15 m and 22 m."

Jan 1, 1988

By T S. Cochrane

A variety of practical tests have been tried in the mining industry to determine the support properties of mine roof bolts. Such tests include torsion wrench readings, hammer blow tests and the use of plates with built-in tension indicators. This paper gives some details of pull tests with a hydraulic jack, as carried out in coal mines of western Canada. M A~Y criteria exist for establishing the efficiency of roof bolting, and the one adopted de-pends on the nature of the problem and on the individual leanings of the investigators. Consequently, sufficient studies have not been made from a common viewpoint or under similar geological and techno-logical conditions to compare these methods of evaluation. However, regardless of whether certain tests provide sufficient factual data to form a basis for theoretical research on bolting or not, many of these tests can and do provide a positive means of judging the suitability of chosen roof bolting techniques and equipment under definite geological conditions.

Jan 1, 1963

By Michael Loken, April Montera

"The process of blending consistent and predictable feed for the roasters is critical to optimizing product quality and controlling production costs. To assist in this process, Online PGNAA Slurry Analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100% of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their Full Stream, Elemental Slurry Analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced."

Jan 1, 2016

By Hongyan Qu, Lihui Zheng

"Horizontal wells in coal seams, Qinshui basin, China are prone to wellbore instability problems induced by drilling, completion and production operations due to the presence of natural cleat network, anisotropy with regard to permeability, brittleness and mechanically weak property of the coal rock. The mechanism of wellbore instability in coal seams is very different from that in conventional formations, the traditional wellbore stability study methods therefore, are not proper for wellbore stability analysis in coal.In this study, the mechanism and controlling of wellbore stability of coal seams in the Qinshui basin was investigated through theoretical modeling, laboratory experiment and field operation. Firstly, a new physical model of wellbore stability for highly-cleated coalbed was proposed, considering the combined effect of mechanical mechanism and reservoir characteristics, specifically, taking the effect of reservoir pore pressure in the vicinity of the wellbore on the wellbore stability into account. Then experiments on the triaxial stress evaluation were conducted at laboratory where rock mechanical parameters such as Poisson's ratio, Young's modulus, compressive strength, tensile strength, angle of internal friction and cohesion ability were measured respectively. The in situ stress at different depths in four wells of Zheng 1-303, Zheng 1-308, Zheng 1-309, and Zheng 1-310 in the Zhengzhuang were calculated, and the collapse pressure and formation breakdown pressure were predicted through the theoretical model we developed. Finally, by comparing the maximum collapse pressure and minimum breakdown pressure of the four wells in the coal as well as in the roof and floor of the coal seams, the fluid weight window for safe drilling in each coal seams was determined, and appropriate approaches against anti-sloughing in coal seams, Qinshui basin were applied in the field operation.The wellbore stability was found not only related to the wellbore pressure, but also affected by the pressure in the reservoir through the theoretical model. The fluid weight window for safe drilling in each coal seams varies with the coefficient of wellbore stability in the model. The laboratory experiment results indicate that the roof and floor of 3 # coal in Qinshui basin has high breaking strength, high heterogeneity, and are easy to collapse and breakdown. In addition, the whole rock mineral analysis shows that 3 # coal in the Duanshi block has high clay content, resulting in the phenomenon of hydration swelling as clay encountered water, and leading to unstable coal and extreme large drilling uncertainties. Due to the effect of the unstable rock mechanical properties of the roof and floor formation on the wellbore stabilizing, drilling parameters, drilling fluid performance and BHA were optimized during the drilling process according to the formation properties, rock mechanical properties and drilling techniques in the field operation."

Jan 1, 2015

By B. K. Gorain

Barrick' s Buzwagi copper-gold deposit in Tanzania comprises oxide, saprock and sulphide mineralized zones averaging approximately 0.058oz/t gold, 0.13% total copper and 0.03% cyanide-soluble copper. A comparative evaluation of the project based on two potential flowsheet alternatives is presented. The first flowsheet included a gravityconcentration and carbon-in-leach (CIL) plant. The second flowsheet was based on a Gravity-Flotation-CIL plant, which proved to be more economically robust. Selective flotation of copper minerals to produce a saleable copper concentrate proved to be challenging. Detailed characterization of the Buzwagi deposit was carried out through understanding of ore mineralogy, mineral liberation, floatability and selectivity, reagent chemistry and regrinding issues. With this insight, a flotation concentrate of greater than 25% Cu was achieved, recovering a significant amount of copper minerals and tellurides. The overall economics of the project improved significantly with the addition of flotation. Leach tests on gravity and flotation tailings showed an overall increase in gold recovery of approximately 6% for a Gravity-Flotation-CIL plant compared to that for a Gravity-CIL plant.

Jan 1, 2007

By Philip J. Bangerter, Chris Twigge-Molecey

Design for safety is critical to metallurgical plants, due to the inherently dangerous nature of their processes. Two significant areas of concern are: 1. preventing catastrophic process failures that cause damage or injury; and 2. operational safety that directly affects those working in or living near the plant. Process safety involves human behaviour, but the designer can eliminate or control hazards by engineering approaches, and control impacts through the design of the operating procedures. The tools available to guide safe facility design include bowtie analysis, hazard analysis, and hazard and operability studies. Clean plant design principles can guide the design process to address in-plant occupational health and safety issues. Auditing and review is a key part of the overall design process.

Jan 1, 2015

By Anoush Ebrahimi

Mining dilution is one of the most important factors affecting the economy of mining projects. Ore losses and dilution are present at all stages of mining and while several models can investigate the influence of dilution it is its quantification that poses the most serious challenge (Pakalnis et al., 1995). This paper introduces a methodology to quantify dilution factor in open pit mines. The proposed approach makes use of general mining software available in most mining companies. Therefore it is amenable to most mining operations and provides a readily available tool for understanding mining dilution for operators and consultants. To illustrate the methodology the author uses an example from a hypothetical mine. Dilution increases the operating costs in the mill by increasing the tonnage of material to be milled. In addition to its direct impact on short term income of a mine, dilution causes significant changes in other factors that on the long term reduce the overall value of the project. For example, it prolongs the mine life by reducing mill?s effective capacity. It also reduces the feed grade. In most cases, lower feed grade means lower mill recovery. Dilution also increases the cut-off grade which in turn reduces the overall ore utilization of a mine. In some cases, to take advantage of economies of scale, mining operations tend to plan for higher mining rates. Moving to a larger scale of operation means less selectivity, hence more dilution. This is true for all kind of deposits. High level and uncontrolled dilution may ultimately defeat the purpose of increasing production rates. If not impossible in theory it is nevertheless extremely difficult and expensive to eliminate dilution in practice. Some amount of dilution is practically unavoidable in most mining operations (Scoble and Moss, 1994). Although completely avoiding dilution may be impossible, we can measure and control it. By better understanding the root causes of the dilution and planning accordingly, it can be controlled and reduced. While we do our best to identify and calculate all the other cost items of a project, no matter how small, it is common to make general assumptions about dilution instead of quantifying it. It is common to assume a general dilution such as 5% for massive deposits and 10% for tabular shape deposits. While these figures may be a good starting point in early stages of mining studies, it does not take in to consideration the complexity of the problem. Dilution factor varies within a single mine for different benches and zones. This is due to changes we see in grade distribution and shape of ore body. It also varies based on commodity price. It is necessary to make sure that these variations are taken into account when designing or evaluating a mine. Dilution varies in different mines based on the deposit characteristics, operational aspects and economic cut-off grade. For instance, shape of the deposit, bench height, equipment size, and market conditions will have an impact on the level of dilution in a mine. It is paramount for mining projects to have a better understanding of dilution right from the beginning. In times like today, where mining operations must operate at peak efficiency, it is even more crucial to be able to calculate and have a better grasp of all the parameters influencing the economics of a project including dilution. In order to produce better project evaluations, dilution studies should be an integral part of any project.

Aug 1, 2013

By J. R. Giegerich

THE problem of dust control in metal mines has, of late years, received considerable attention. In 1932, a detailed study of dust conditions at the Sullivan mine was undertaken and, while there are no actual data available regarding conditions prior to that date, there has unquestionably been a great improvement as a result of the investigation and of the preventive methods adopted. In attacking the problem, three main factors were considered: first, and most important, how to prevent dust from being formed; second, how to depress or collect it if formed; and third-if unable to accomplish these-what precautionary measures must be adopted to prevent inhalation of this dust. Seven distinct methods of dust control are now practised at the Sullivan. Six of these are employed underground; they are tabulated below in the order of their relative importance. The seventh method is used in the crushing plants on the surface. (1) Improved ventilation (2) General use of water sprays and atomizers (3) Curtailment of secondary blasting during shift hours ( 4) 100 percent wet drilling-primary and secondary (5) Wearing of protective equipment (6) Change from carbide to electric lamps (7) Installation of dust collectors

Jan 1, 1936

By Douglas A. Sloan

"Shutdowns and breakdowns that halt the process-flow of mine production are costly. Skilled maintenance tradesmen are scarce and expensive. The cost of maintenance or of production Joss from Jack of maintenance is significant and warrants considerable managerial attention.The most appropriate maintenance policy is dependent on an economic calculation. At one end of the spectrum is the policy of avoiding all breakdowns by replacement and preventive routines before failure, such as the airlines policy. At the other end of the spectrum is the policy of minimal routines and the acceptance of a breakdown as a prelude to a repair.The complexity and cost of maintenance warrants the appointment of a maintenance manager of senior status. Within the origination, there are a number of activities that can be specialized to improve effectiveness. Among these are the inspectors' activity, the establishment of improvement routines, the planning of repair tasks, maintenance engineering research and value analysis.The maintenance system is the mechanical aid to assist the staff in the implementation of the policy. It is designed to facilitate planning to make the best use of the resources. It provides information to identify areas where managerial action is required to make improvements. The job ticket is the basis of most systems."

Jan 1, 1970