Search Documents

By L. Li

To accommodate the large payloads and harsh operating conditions associated with heavy vehicles in the mining industry, off-the-road (OTR) tires are typically used with heavy mining vehicles. These tires have increased abrasion and wear resistance due to their thicker tread, sidewall and bead thicknesses. Given these features, OTR tires are much stiffer than conventional passenger vehicle tires and cannot be mounted to a single-piece rim without damaging the structural integrity of the tire during the mounting process. Therefore, multi-piece wheels are used with OTR tires to facilitate mounting. While these assemblies are necessary, several instances of their failure have been reported to result in injuries or fatalities within the mining workplace. Many of these failures were specifically reported to be caused by the disengagement of the wheel lock ring - a component used to securely engage the assembly during operation. In this study, a threaded-connection locking mechanism has been proposed in place of the traditional lock ring design. The performance of this threaded-connection was numerically evaluated in a pull-out test against a conventional five-piece wheel assembly. The pull-out test was devised as a means of quantifying the engagement ability of each wheel?s locking mechanism. A high degree of modelling accuracy was maintained throughout the analysis by validating the vertical and horizontal static loaddeflection behaviour of the rim model of the five-piece wheel assembly against experimental data. Through validation, the model data were found to be within 10.5 and 4.80 %, for vertical and lateral loaddeflection behaviour, respectively. Results from the pull-out analysis found that the threaded-connection demonstrated a 113 % increase in the force required for disengagement to occur relative to the conventional five-piece design - a force of 9,550 kN in total.

Aug 1, 2013

By Lorrie Fava

Two needs in the mining industry, to enable overall process improvements, are open systems and network connectivity in underground mines. The Pando project, a collaboration between Symboticware, Vale and Xstrata Nickel, and supported by CEMI, addresses these issues, and leverages the solution platform to deliver intelligent applications. An open system is one that uses publicly available standards for its key interfaces. Vendor-neutrality and ease of information flow are two main benefits that result from the use of open systems. By facilitating the interoperability of systems, open systems allow information to be available when and where it is needed for decision support. Network connectivity in underground mines is typically limited, with hotspots in strategically chosen areas that are relatively static. Mobile equipment moving through a mining work cycle experiences intermittent connectivity; in this situation, seamless remote equipment monitoring is impossible. The Pando project establishes an open technology platform, adhering to the IREDES and OPC UA standards. It enables the collection and integration of information generated by mobile equipment? seamlessly while there is a network connection, and as a store-and-forward gateway to manage intermittent connectivity. The platform capabilities are leveraged to support embedded intelligent applications. This open platform, the SymBot, is a rugged hardware and software device. The platform complies with open standards for industrial automation and systems interoperability. The SymBot platform is capable of providing advanced real-time decision support at the device level, and is designed to be remotely configurable. Applications being developed through the Pando project include engine monitoring, a dynamic load weighing system, machine location monitoring and automated activity monitoring including production and maintenance reporting.

Oct 1, 2010

By T. C. Crosby

"Grinding has a marked effect on concentrator recovery and operating cost, and improved operation through automatic control can enhance plant performance. The correct application of automatic control can only be accomplished after the basic process variables and their effect on mill operation have been defined. This paper develops a control system for a closed circuit grinding system. Typical control systems, such as those for feed, water flow, level and circulating load, are discussed. A method of determining controllability, using the calculated reaction curve technique, is outlined. Various successful automatic grinding control applications are discussed and future possibilities are outlined. Although this paper primarily deals with closed wet grinding• circuits, the principles involved can be readily applied to other processes."

Jan 1, 1967

By S. Banisi, A. R. Hasankhoei, Gh. Parsapour, A. R. Ghasemi

At the Gol-E-Gohar mining and industrial Company, a pelletizing plant, which includes two parallel dry closed grinding circuits and a pellet production circuit, produces 600 t/h. Each grinding circuit consists of a burner, a dry ball mill (6 m×13 m) and an air separator. Each ball mill consists of a 2 m-long dryer chamber and an 11 m-long grinding chamber. Iron ore concentrate is fed to the drying chamber to decrease its moisture from 2.5% to below 0.2%. The drying chamber consists of 56 flights in two rows. It was found when the feed moisture content decreased from 1.3 to 3.5%, the throughput decreased by 14% (40 t/h) indicating a low performance of the dryer. In order to improve the efficiency of the drying section, a scale down version of the dryer was constructed in a 1m diameter mill with a transparent end to make image analysis possible. It was found that because of the inappropriate veiling profile in the drying section, most of materials are not subjected to the hot gas tunnel. To overcome this problem, various flights with different geometries were physically tested and also simulated by the KMPCDEM © software. With the aim of arriving at a proper veiling profile which maximizes the particles contact with hot air, a new flight design was obtained and tested. The installation of the rectangular tooth type flights in one of the mills in the plant made the comparison of the old and new designs possible. The evaluation of the designs in a period of three months indicated 15 t/h increase in the throughput in the case of the new flight design.

Jan 1, 2016

By John G. Ayttes

"The following is a review of the advance of raise boring and its current position. The viewpoint presented is that the mining industry, through its worldwide acceptance of raise boring, has acknowledged the success of the method in general. Acceptance, however, does not imply complete satisfaction with either the equipment or current operating costs. Therefore, a brief review of how boring costs are being r educed is presented, citing examples. Recent raise borer applications of special interest are presented to show adaptability of current equipment, and some special projects in the planning stage are highlighted."

Jan 1, 1972

By M. Tanaka, H. Narita, K. Morisaku

"The selective separation of palladium (Pd), platinum (Pt), and rhodium (Rh) from a hydrochloric acid solution by solvent extraction was investigated using amide-type extractants, i.e., N,N,N’,N’-tetra-n-octyl-thiodiglycolamide (TDGA) and N-n-hexyl-bis(N-methyl-N-n-octyl-ethylamide) amine (BisAA). The separation experiments employed two separation schemes: (1) extraction of Pd with TDGA and that of Rh and Pt with BisAA; and (2) extraction of Rh, Pd, and Pt with BisAA. Separation scheme 1 achieved the highly selective separation of each metal. For separation scheme 2, Rh can be recovered prior to Pd and Pt, despite having a lower selectivity for Pd/Pt than separation scheme 1. INTRODUCTIONThe recent increase in the use of platinum group metals (PGMs) in industry (especially auto catalysts containing palladium (Pd), platinum (Pt), and rhodium (Rh)) has lead to their increasing waste; therefore, improvements in the recovery techniques for PGM have received significant attention. In metal refineries, PGMs are mainly separated and purified by solvent extraction (Cox, 2004). The extraction process used in INCO’s Acton precious metal refinery is one of the most famous commercial processes and is utilized worldwide. In this process, silver is first removed as a residue (AgCl), and then gold, Pd and Pt are extracted from hydrochloric acid (HCl) solutions using dibutylcarbitol (DBC), dialkylsulfide (DAS), and tri-n-butylphosphate (TBP), respectively. Finally, Rh remains in the raffinate (Barns & Edwards, 1982).The development of a successful solvent extraction process depends on the choice of the appropriate extractants. We have studied the extraction of PGM using N,N-disubstituted amide compounds (Narita, Tanaka, Morisaku, & Abe, 2004; Narita, Tanaka, Morisaku, & Tamura, 2006; Narita, Tanaka, & Morisaku, 2008a, 2008b). They are relatively stable against acids, and their metal extractability can be improved by changing the side chain length and/or introducing additional donor atoms like sulfur and nitrogen. We have recently found that thiodiglycolamide and an amide-containing tertiary amine have good extractabilities for Pd and Rh, respectively."

Jan 1, 2012

By A. K. Debnath

The water resource is key to survival of the mankind and this resource is now becoming critical in many parts of globe including India. As per an assessment of Central Ground Water Board (CGWB) of India, a huge shortfall of about 58 billion m3 of water is anticipated by the year 2050. In order to counter this shortfall, there is thrust from Government of India to adopt water conservation measures. National Environment Policy, 2006 of Government of India also stresses upon the need to take up water conservation measures for water security of the country. The coal mines in India provide an excellent opportunity to take up water conservations measures therein. The mine water is not acidic unlike western countries and it conforms to the prescribed regulatory standards. This nature?s gift is utilized in Coal India Limited by allowing mine voids to get filled with mine water. The net recharge potential of the opencast mining area is found to be about 5% in comparison to 2% in non-mining area offering good prospects for ground water recharge. The seasonal rainwater is also diverted into mine voids left at the end of mining operations which act as huge reservoirs/ pit lakes for storage of the water. They also serve as surface water bodies for recharging of water table in the surrounding areas. The area and space left from where coal has been extracted completely in underground mines and will not be entered by any man or machinery after the extraction, called goaf, are also potential source of water conservation. These additional water resources created are being utilized for meeting the industrial, domestic, irrigation and other requirements of the projects and local communities eliminating the need to tap other fresh water resources including ground water. Presently, 75% of the water demand of the coal mining project is being met from the water stored in the mine pits. In future, CIL is likely to create about 3.3 billion m3 of water resource, on an average, in its opencast mines alone. In the mine closure plan of opencast mines, the last cut is proposed to be developed into water body for recharge of ground water and creating additional water resources. A clean potential source of potable water is thus developed after mine closure. This will ensure water security of the country.

Aug 1, 2013

By N. A. Beier, N. Slingerland

"Oil sands tailings impoundments rank among the largest (spatially) in the world, covering a total of approximately 220 km2 of northern Alberta, Canada. A preliminary geomorphic design for an oil sands tailings storage facility (TSF) landform was completed with the goal of eventual closure and delicensing in mind. This paper outlines methods identified during the design process that streamline closure when implemented early in the mine planning and TSF design stages. With most oil sands TSFs currently in active operation (and some still in the planning stages), geotechnical engineers and mine planners have the opportunity to make operational and design decisions, such as those outlined herein, that are likely to improve the geotechnical and environmental performance of the landform post closure. ¦ KEYWORDS Alberta, Athabasca oil sands (AOS), Landform design, Reclamation, Sand dam, Tailings storage facility (TSF) RÉSUMÉ Les bassins d’accumulation des résidus issus des sables bitumineux font partie des plus grands (en termes d’espace) au monde, et couvrent au total environ 220 km2 dans le nord de l’Alberta, au Canada. Une conception géomorphologique préliminaire a été réalisée pour le modelé d’une installa¬tion de stockage des résidus (ISR) issus des sables bitumineux en gardant à l’esprit la fermeture et le retrait de permis à terme. Cet article présente les méthodes identifiées pendant le processus de conception qui simplifient la fermeture lorsqu’elles sont mises en oeuvre dès les premières étapes de planification de la mine et de conception de l’ISR. La plupart des ISR issus des sables bitumineux se trouvent dans des exploitations actives (dont certaines en sont encore aux étapes de planification), aussi les ingénieurs géo¬techniques et les planificateurs miniers ont la possibilité de prendre des décisions en termes d’exploita¬tion et de conception, telles que celles présentées ici, qui pourraient améliorer la performance géotechnique et environnementale de la phase suivant la fermeture du modelé. ¦ MOTS CLÉS Alberta, assainissement, barrage de sable, conception du modelé, installation de stockage des résidus (ISR), sables bitumineux de l’Athabasca (SBA)INTRODUCTION The Athabasca oil sands (AOS) underlie 140,200 km2 of land in northeastern Alberta, Canada. Oil sands located within 100 m of the original surface account for 4,800 km2 of the total area and are considered to be economically mineable (Figure 1; ERCB, 2009). Bitumen, the thick, tar-like substance contained in the AOS, is extracted through open-pit mining and in-situ methods. During mining, the overburden is first removed as waste and the sandy, bitumi¬nous ore (“oil sand”) is transported to processing facilities via conveyor belts and 400 t trucks. Warm and hot water, as well as process aides such as caustic soda, are mixed with the oil sand, creating a slurry from which bitumen is mobilized and extracted. The resulting slurry waste product is called “tailings” and contains mineral solids, process water, and small proportions of unrecovered bitumen (Masliyah, Zhou, Xu, Czarnecki, & Hamza, 2004; Sobkowicz & Morgenstern, 2009)."

Jan 1, 2019

By A. Todd Davis

"Introduction“CAN YQUR Company afford not to train?"" This question was asked by Jack Taylor in the Factory Management Magazine for June, 1950. Mr. Taylor went on to say, ""No, it can't; no Company can"". It's true that many training programmes have not done the job they were designed to do because of a number of factors such as parts of management resenting training, management failing to understand the abstract values of training, and management giving impossible assignments or picking the wrong trainers. However, Mr. Taylor summarizes his article by saying that a properly-designed and •conducted training programme brings a company or a corporation to the point where the question is: ""Can my Company afford not to train?""About two years ago, in July, 1952, Nevada Mines Division of the Kennecott Copper Corporation embarked on a training programme, the same type of programme that had been inaugurated earlier at the •Utah Copper Division at Bingham, Magna, and Garfield, Utah. President Charles Cox of Kennecott, in •a speech made •before the Utah Bankers Association in June of 1951, stated that, ""I think that our programme of employee training is one of the most important phases of our entire operation"". That statement might be said to be one of the guiding principles of training at Nevada Mines Division. Training is supported by top managements and down the line to Division managements. As the years go by, the Company expects to receive many benefits from training."

Jan 1, 1954

By George Wilkinson

"AbstractThe consistent relationship between the availability of electrical energy and our economic wellbeing is well known. As we develop the energy we need to nurture industrial civilization in decades ahead, we will at the same time reduce our reliance on dwindling supplies of oil and gas. Coal and uranium will be developed as our major fuel sources to meet medium-term. energy needs, followed by fusion and solar energy for the long term.IntroductionTHIS PAPER treats the matter of energy in a way that is quite different from that of the crisis-type atmosphere which surrounds so much of it currently in the news media. On the one hand, we lift the whole subject of energy out from its present-day involvement with short-term issues and take an important longer-term look at the solutions which lie before us. On the other hand, we recognize that short-term issues are important and, as we are reading and hearing, many of the right short-term solutions continue to elude our politicians, our policy makers, and even some of those with knowledge and authority in the energy field.A year ago, if you asked people how they would go about conserving energy, they would probably have said turn out the lights. They would probably say the same thing today, but they might also include other things such as driving the automobile more slowly or putting more insulation in the attic. However, their first impulse is still to use less electricity."

Jan 1, 1977

Mineral engineering is defined as those engineering activities that relate to the discovery, development and utilization of mineral resources. Using petroleum engineering as an example, it is shown that the breadth of the field to be studied is a major educational problem. Breadth of field is aggravated by the rapidity with which technological demands may change. At present, special short courses serve to update engineering education. Recent experience suggests an increased rate of change for the future. The fact that engineers have typically human needs and goals, and the fact that engineers respond to these in our free society, introduces a third class of problems. One approach to the solution of these problems is the unified engineering curriculum based on a core of subject mat-ter common to all engineering. Experience suggests that the unified curriculum is an effective method to minimize the importance of the first two problem areas presented, and shows a degree of success in handling some problems within the third area. Perhaps, for the good of all segments of society, it is best to have both career-oriented and unified curricula represented by educational institutions of high quality.

Jan 1, 1963

By J. Clark

Erosion control during the mining cycle can be more effectively planned using Erosion and Sedimentation Control Plans (ESCPs). This raises the issue of who should develop an Erosion and Sedimentation Control Plan Guidance document (ESCPG) to standardize the content of ESCPs. A search for ESCPG documents in Canada revealed no examples for mine sites. In the U.S. there are a number of regulatory authorities who developed such documents for mine sites, including EPA. An ESCPG is expected to result in: (a) plans will be more standardized (b) more clarity and efficiency for those generating ESCPs; (c) assisting regulators tasked with reviewing/approving ESCPs; (d) providing guidance for the mine effluent permitting process relative to sediment control; (e) providing a basis for developing and including ESCPs in the Environmental Assessment (EA) phase and the mine economic assessment; (f) applying and optimizing ESCPs above the ?watersheds? of sediment ponds; (g) utilizing the ESCPG document for ?exploration? sites; (h) lowering the risk of adversely impacting water quality downstream of mining activities; (i) providing a methodology for determining the need for sedimentation pond(s) during the construction and production phases; and (j) providing a clear environmental sustainability message relative to sediment control if the mining industry takes the lead in developing an ESCPG. ESCPs will proactively create increased administrative (regulatory) efficiency in the EA and sub-EA reviews relative to erosion control and sediment release from mine sites. This also assists the new initiative in BC, One Project, One Process (OPOP) and synchronous permitting (a variation of concurrent permitting): as an example, enhanced erosion control planning at the EA phase then allows the synchronous permitting initiative to proceed efficiently, particularly for the mine permit (Ministry of Energy, Mines and Natural Gas) and effluent permit (Ministry of Environment). Approximately twenty more management plans (e.g. ARD/ML, explosive management, emergency response, hazardous waste, sediment pond operation, environmental effects, environmental sampling, etc.) may also be entered into the EA process to create increased efficiency, and then feed into the synchronous permitting effort. The BC OPOP initiative also adds support to the Canadian Federal ?One Project, One Review Process? approach. The ESCP and a sediment pond management plan will also address the Canadian Metal Mining Effluent Regulations requirement for all discharges from mine sites to meet a grab sample of 30 mg/L Total Suspended Solids.

Aug 1, 2013

By J. G. Debanne

MOST company-employed petroleum engineers have in their accounting departments punch-card computers that can perform engineering calculations thirty to three hundred times faster than desk calculators, or they can rent such machines from Computing Service centres. These machines not only eliminate the drudgery of desk calculation but also the risks of human errors. The I.B.M. t 604 punch-card computer of Texaco's accounting department in Calgary has been used for oil and gas property evaluations, curve fitting by least squares, statistical core analysis studies, unsteady-state water in-flux studies, phase equilibrium performance prediction of oil reservoirs, gravity segregation calculations, etc.

Jan 1, 1958

By M. T. Ho, D. E. Wiley

The iron and steel industry accounts for almost 5 % of the total world CO2 emissions. Optimisation of the steelmaking process has led to significant reductions in the energy intensity to the point where it is now close to the thermodynamic limit. Further reductions are not likely to be achieved with efficiency improvement alone and will require the development of novel or breakthrough technologies. This paper will show the costs of implementing CO2 capture at direct atmospheric emission points for a number of iron and steel production processes. These include a conventional process, top gas recycling processes, the Corex and Hismelt smelt reduction processes and the Midrex direct reduction process. Depending on the point source emission, costs of capture with existing chemical absorption technology at iron and steel plants can be similar to capturing CO2 at pulverised coal fired power plants.

Jan 1, 2015

By Burns Sutherland

Although some mine hoisting systems incorporating steel wire ropes on drum hoists experience completely dependable performance on the hoist ropes for many years, other rope records illustrate an erratic behaviour pattern and, as such, become a source of concern to the operator. This paper describes the causes of the difficulties most commonly encountered and incorporates methods of providing preventative or corrective maintenance. When such a program is utilized wisely, within the allowable limits of shaft time available, it can be the means of avoiding many unforeseen circum-stances and of reducing operating costs, as well as rope costs, to a mini-mum.

Jan 1, 1970

By E. L. Bruce

EUROPEAN Russia is mainly a great plain, the average elevation of which is only 600 feet above sea level and the maximum elevation less than 1,200 feet (Figure 1). The main divide between the Arctic ocean and the Black sea and Caspian sea is an indistinguishable topographic feature from which the Dneiper and Don rivers flow southward to the Black sea and the Volga river to the Caspian. The valleys of these rivers are but little below the general level (Figure 2). To the south, this great, rolling plain is broken by a low ridge of Precambrian gneisses and intrusive rocks. The Crimea is an upland from which the descent to the Black Sea coast is precipitous (Figure 3). The Ukrainian Soviet Socialist Republic occupies the southern part of the plain. It is the southwestern unit of the Union, bordered by Rumania and Poland on the west and by the Crimean Soviet Socialist Republic on the south.

Jan 1, 1938

By J. Edwin Van Buskirk

For a country that is as important a gold producer as Canada, the return to the gold standard of the major commercial countries of the world during the past five years is of particular significance. To the Canadian gold mining industry, the advantages of the gold standard are a matter of more than theoretical importance. According to economic theory, prices are determined by the relation between the demand for, and the supply of, money. The demand consists of the offering of goods for money; the more goods offered, the greater the demand. The supply consists of the total money available for the purchase of goods. The total supply of goods to be exchanged through the instrumentality of money remaining the same, an increase in the supply of money will, according to this theory, raise prices; conversely, a decrease in the supply of money will lower prices. Let us imagine that everyone in the world suddenly had twice as much money, and that the sum total of all goods remained the same. Is it not obvious that we would pay just double the price for these goods? In Canada today, most people have approximately 50 per cent grea.ter income than in 1913, and the average price for all articles sold in Canada is 50 per cent above those in 1913.

Jan 1, 1928

By D. F. Scott

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE REGION of Western Canada covered by this re-port lies between the Precambrian rocks of the Canadian Shield and the structurally deformed rocks of the eastern Cordillera, extending northward from the international border to the 60th parallel. It is some 487,000 square miles in area, with a total sedimentary fill of about 535,000 cubic miles0>. It includes parts of the prairie provinces of Manitoba, Saskatchewan and Alberta and the northeast corner of British Columbia and forms part of the geological region known as the Interior Platform, commonly referred to as the Western Canada Sedimentary Basin. The bedrock comprises carbonates and evaporites of Paleozoic age that lie on Precambrian crystalline rocks and are over-lain by a relatively thick blanket of Mesozoic and Tertiary elastic rocks. The nearly flat-lying bedrock, covered by a thick mantle of glacial drift, forms the Interior Plains physiographic province."

Jan 1, 1970

By J. Beland

The Rimouski-Matapedia region is along the southwestern extension of the central Siluro-Devonian synclinorium of Gaspe Peninsula. As in Gaspe about 30,000 feet of Siluro-Devonian strata rest on a "basement" of tightly folded Ordovician rocks. The central synclinorium is divided up into two northeasterly trending belts each of which is characterized by distinctive lithologies and patterns of folding. The northwestern belt is gently to moderately folded and includes lithologies which point to a stable environment. The southeastern belt on the other hand is tightly folded and the lithologies indicate a less stable environment. A marked angular unconformity separates the basement from the Siluro-Devonian cover near the north-western margin of the northwestern belt. At the southeastern margin of the southeastern belt the relationship of cover to basement has not been as-certained because of a fault. The northwestern belt has several features significant in the search for petroleum; the Silurian strata are exposed in broad open anticlines

Jan 1, 1962

By B. R. Conard

Occupational epidemiology of the nickel-producing industry has found that inhalation exposures to certain nickel-containing substances are linked to respiratory cancers and to nonmalignant respiratory endpoints. Establishing such a linkage, however, is complicated by the fact that some diseases occur long after exposure to a causal agent (i.e., some diseases have long latencies). Furthermore, most chemical agents (especially nickel substances) vary significantly in their toxicological properties and their concentrations in workplace air have varied over processing history. Because of these complications, it is critical to understand historical exposures to specific nickel substances. To assist in this effort, the author focuses on the history of smelting and its related processes at Vale Canada’s (Inco’s) Ontario operations in the first half of the 20th century.

Jan 1, 2012