Search Documents

By V. V. Pankov, W. R. Chen, L. R. Zhao

Diffusion nickel aluminide and overlay NiCrAlY coatings were deposited on single crystal Ni-base superalloy CMSX-4 substrate using the chemical vapour deposition and cathodic arc evaporation techniques, respectively. The NiCrAlY coating underwent a post-deposition heat treatment in an argon atmosphere at 1100°C for 2 hours. All the coated specimens were subjected to furnace cyclic oxidation testing at 1000°C up to 1500 one-hour cycles. The morphology, elemental composition and phase constituents of the oxide scales formed on the coating surface were analyzed using scanning electron microscopy, energy-dispersive spectroscopy and X-ray diffraction. It was observed that the diffusion aluminide coating experienced accelerated weight gain at an early stage of the test (150-400 cycles), whereas the overlay NiCrAlY coating fabricated by cathodic arc evaporation maintained steady-state weight gain throughout the entire 1500 cycle test duration. This difference in oxidation behaviour between the two types of coatings is attributed to the early development of nickel-aluminum spinel on the surface of the diffusion aluminide coating, in contrast to the stable aluminum oxide scale formed on the overlay NiCrAlY coating during cyclic oxidation testing.

Jan 1, 2015

By Schoeman L., K. C. Sole

Evaluation and measurement of the influence of changes in conditions and electrolyte composition during early stages of a growing metal electrodeposit are crucial to predict changes in developing morphology. A galvanodynamic polarization technique was developed to reliably measure overpotentials for nickel electrodeposition from sulfate electrolyte. The validity of these polarization parameters as indicators of the relationships between changes in the electrolyte and resulting deposit morphology was evaluated for electrolytes of varying composition. Findings indicate that nucleation and plating overpotentials measured by the described technique can be used as indicative tools for monitoring, evaluating and ultimately improving control of the electrodeposition of nickel from sulfate electrolytes. The results predict that nickel deposits of desirable quality and morphology are obtained when plating overpotentials are higher than 700 mV vs. Ag/AgCl and nucleation overpotential is less negative than plating overpotential.

Jan 1, 2017

By V. Prasad, A. Afacan, K. Popli, S. Dubljevic

Froth flotation is one of the most common and widely used separation processes in the mineral processing industry; however, its complexity means that complete understanding of the process has not yet been achieved. A dynamic fundamental model is needed to enhance the understanding of the process and to improve process control. It is challenging to capture all the phenomena involved; hence, we propose a multiscale modeling approach with a framework ranging from macroscopic (equipment scale) to microscopic (attachment, detachment) models along with distribution models for ore particle sizes. Real-time froth properties are obtained using a vision-based sensing system. These measurements can be used for developing a soft sensor for grade using statistical methods such as PCR (principal component regression) and PLS (partial least squares) regression. The fundamental model is updated in real-time using extended Kalman filtering. Attachment dynamics are studied for different particle size distributions. The modeling and soft sensing is tested on batch flotation cell for the pure mineral galena with different particle size distributions using Xanthate and MIBC as collector and frother, respectively. The model, online measurements and soft sensor are useful in developing monitoring methods for froth flotation.

Jan 1, 2015

By R. A. Campbell, R. R. Rogers

"AbstractThe experiments described show that crude bismuth metal containing up to 5 per •cent lead, 0.14 per cent silver, 0.015 per cent copper, 0.02 per cent iron, .and small amounts of antimony, nickel, and tin may be refined to a bismuth content of 99.98 per cent by distillation followed by chlorination. It also is shown that bismuth trichloride of high ,purity may be produced by passing chlorine over hot •crude bismuth metal and allowing the resulting vapours to •condense in a cooler .part of the system.IntroductionBISMUTH is used in the production of alloys and pharmaceuticals. During 1952, the New York price for the refined metal was $2.25 per pound in ton lots.Some months-ago a Canadian producer requested the Mines Branch to investigate methods of refining the bismuth which they had been producing. Their crude product had been selling for $1.50 to $1.70 per pound and it was desired to increase its purity to at least 99.98 per cent so that it could be sold for $2.25 per pound."

Jan 1, 1955

By Eduardo R. Rodrigues, Ankur Narang, Roberto Federico Ausas, U. T. Mello, Jose Maria Segura Serra, M. R. Lakshmikantha, Ignacio Carol, Kamal C. Das

"Modeling of big faults or weak planes of strong and weak discontinuities is of major importance to assess the Geomechanical behaviour of mining/civil tunnel, reservoirs etc. For modelling fractures in Geomechanics, prior art has been limited to Interface Elements which suffer from numerical instability and where faults are required to be aligned with element edges. In this paper, we consider comparative study on finite elements for capturing strong discontinuities by means of elemental (EFEM) and nodal enrichments (XFEM) for Geomechanical applications. For general fracture scenarios, Oliver et al. (2008) have demonstrated advantages of EFEM over XFEM for including: (a) ease of modeling in any standard finite element code due to the possibility of static condensation, (b) higher accuracy in some cases for coarse meshes, and, (c) a reduced computational cost. However, there has been no work that considers cohesive fractures in Geomechanics. We present a numerical analysis based on a linear constitutive model and linear triangular elements for the bulk and a linear constitutive behaviour for the fault for a representative set of fault planes in a circular tunnel made in rock mass. In the numerical examples we consider both well-traced and bad-traced meshes. We focus on traction profile analysis for both EFEM and XFEM, since that is crucial to understand the cohesive fracture behaviour specially rock joint. Therefore in each case, shear, normal and stress ratio are compared across the two methods along the fault plane. This is the first such work that compares XFEM and EFEM behaviour for Geomechanics problems.For the considered class of problems and the sharp penalization approach without regularizations adopted, it can be observed that accuracy and robustness of EFEM may strongly depend on the fault orientation with respect to the element edges, while, XFEM is independent of fault alignment with element edges. It has been also observed that, with mesh refinement model, stress oscillation completely removed with XFEM however EFEM fails to provide oscillation free results with finer mesh in case bad-traced model. We also performed error analysis and found that in case of bad-traced mesh the average error in the XFEM is 84% smaller than of EFEM and for XFEM the error goes to zero with increasing mesh resolution, while for EFEM the error increases with mesh resolution. Thus, we experimentally demonstrate that, XFEM performs better than EFEM in terms of accuracy and rate of convergence with marginal increase in computational cost. This work hence provides novel insights on the application of XFEM and EFEM in Geomechanics."

Jan 1, 2015

By Ralph J. Holmes, David McCallum, Alan Roberts, Rolando Orense, University of Auckland, Tobias Krull, Tom Honeyands, Kenneth Williams

"The safe ocean transport of bulk commodities like iron ore, coal, nickel ore, manganese ore and bauxite by large bulk ships is vitally dependent on the stability of the cargo under the influence of wave induced ship motion. Safety standards are set by such bodies as the International Maritime Organisation (IMO) with recommended tests for the assessment of bulk commodities. Since the 1960s, the bulk cargo code (BC Code) commenced defining methods to determine the Transportable Moisture Limit (TML) for transportation of bulk commodities. By the latter part of the 1960s, three TML test methods were defined, namely the Flow Table, Proctor-Fagerberg and Penetration tests. All three tests were predominantly aimed at determining TML values for mineral concentrates.More recently, bulk commodity producers, Maritime Organisations and Port Authorities worldwide have been investigating whether commodity based TML methods better reflect realistic safe ship transportation than the current concentrate based TML test methods. In these investigations, the relationship between the mineralogical and particulate parameters of specific commodities with respect to cargo stability and moisture retention has provided insights into the development of tailored TML test methods. To this end, an AMIRA International project (P1097) undertaken by CSIRO, TUNRA Bulk Solids, the University of Newcastle and the University of Auckland assisted the IMO Technical Working group to investigate the relationship between iron ore fines characteristics and a new TML test specific for iron ore fines bulk cargoes.A review of the three standard concentrate based TML methods and characterisation studies of iron ore fines, as well as cyclic triaxial testing to determine liquefaction resistance, resulted in the development of a modified Proctor-Fagerberg method for determining the TML of iron ore fines. Of particular importance in determining TML is mineral composition, porosity, particle density and allowing time for moisture equilibration."

Jan 1, 2016

By A. G. Darnley

"IntroductionTHE PURPOSE of this paper is twofold. Firstly, to drawn attention to recommendations which have been accepted by the International Atomic Energy Agency concerning radiometric reporting methods and calibration in uranium exploration, and secondly to emphasize the benefits that- will stem from adopting them. These recommendations are contained in an IAEA Technical Report, No. 174, which has been prepared with the intention of serving as a general guide to the subject. The existence of this specialized report is likely to be unknown to most of those who can benefit unless it is given some publicity by an organization such as the CIM. The recommendations were prepared by a small international committee consisting of Dr, P. H. Dodd , U.S .A. , Dr. R. L. Grasty. Canada, Dr. L. Levborg, Denmark, Dr. M. Matolin, Czechoslovakia , Dr. S. D. Simov, Bulgaria, and the writer.The fact that there are standard scientific units of mass, distance and time is taken for granted, It is also accepted that the type of instrumentation used to measure one of these parameters is irrelevant to the way the measurement is reported. Geophysical parameters such as magnetic field strength and gravity have generally accepted units, the gamma and milligal, which are defined in SI terms. These units are employed irrespective of the operating principle, or manufacturer or organization involved in the measurement."

Jan 1, 1977

By J. Ouellet

The authors participated in a study for a new mine shaft in Saskatchewan?s Athabasca Basin where ground freezing is desired to reduce water inflows. Constraints were imposed on the design in terms of permissible water leakage (less than 10 m3 / hour) inside the shaft. Since the shaft goes through highly permeable formations, water control measures had to be incorporated into the design. Ground freezing was selected as the most reliable and proven method for the sinking and a hydrostatic liner design was implemented. While exploring various technological options available for providing a fully hydrostatic liner, the authors came up with a new design concept that offers a more cost effective solution while meeting all the design constraints. The new liner concept is a composite design using concrete and a sprayed-on membrane system. A proof of concept program comprising laboratory testing and field testing was successfully implemented. This paper presents the innovative liner design, as well as the adapted sinking methodology, developed for this type of project. The new concept offers a new cost effective high performance hydrostatic mine shaft liner comparing favorably with traditional methods. RESUME: Les auteurs ont réalisé une étude pour un nouveau puits de mine dans le Bassin de l?Athabasca en Saskatchewan. Des limites sévères sont imposées sur le design en terme de volume d?infiltration d?eau acceptable (moins de 10 m3 / heure). Comme ce puits de mine traverse des formations très perméables la congélation des terrains a été sélectionnée, une méthode éprouvée et fiable. Un design hydrostatique a été choisi pour le revêtement du puits. Dans le processus de design, les différentes technologies disponibles ont été étudiées. Les auteurs ont développé un nouveau concept de revêtement composite offrant un rapport performance/prix plus avantageux que les technologies conventionnelles. Le nouveau design proposé est composé de béton et d?une membrane projetée. Un programme expérimental a été réalisé pour démontrer la faisabilité du concept. Cet article présente le nouveau concept ainsi que la méthodologie de fonçage de puits adaptée. Ce concept innovateur offre un revêtement hydrostatique performant à un cout avantageux par rapport aux techniques de construction utilisées jusqu'à maintenant.

Jun 1, 2012

By Haibin Ma, Jie Song, Qingyou Han, Xiaoming Wang, Wei Vian

In the grain refinement of aluminum, Al3Ti and TiB2 particles are introduced to reduce the casting grain size down to 200 micrometer level, which makes cold working possible. The particles are brought in by the addition of Al-Ti-B type master alloys. It is generally believed that TiB2 particles are stable and nucleate a-Al grains in solidification in the presence of extra titanium than the stoichiometry of TiB2 from the dissolution of Al3Ti particle in the master alloys. Titanium in solution either form Al3Ti layers on the surface of TiB2 particles or as solute to promote the nucleation and to restrict the growth of a-Al grains. However, a consensus on a grain refinement mechanism is still to be reached due to the lack of direct observation. This paper presents finding on the TiB2/Al3Ti interfaces in an aluminum matrix. It demonstrates a strong epitaxial growth of Al3Ti on the surface of TiB2 particles, a sign of the formation of an Al3Ti layer on the surface of TiB2 particles in grain refinement practice. The Al3Ti layer has a crystal coherency with a-Al and hence offers a substrate for heterogeneous nucleation of a-Al grains.

Jan 1, 2015

By C. S. Lord

"AbstractThe slow progress of conventional geological reconnaissance of the northern Canadian Shield during the past twenty years clearly indicates the need for a radically new field technique. Operation Keewatin, involving the use of helicopters as the traversing vehicles, was planned and executed by the Geological Survey of Canada in response to this requirement.About 57,000 square miles of District of Keewatin, N.W.T., were mapped during the 1952 field season in appropriate detail for publication at 1 inch to 8 miles. The Operation disclosed about 14,100 square miles of Precambrian sedimentary and volcanic rocks ranging in •age from Archaean to Late Proterozoic. About 7,700 square miles of this area are underlain by greenstone. This work was accomplished in a field season of 113 days, including the spring break-up. Routine aerial geological observations were made from two helicopters flying about 300 feet above the ground; these observations were checked by more than 1,700 landings and about an equal number of aerial observations from heights of less than 50 feet. Logistical support was •provided by a Norseman aircraft on skiis or floats. Combined helicopter and Norseman flying time was about 990 hours. More than 1-00 square miles were mapped per helicopter-hour, and about 815 square miles were examined each day that both helicopters operated. The reconnaissance cost about $207,000, or $3.63 per square mile mapped.As a result of this trial use of helicopters there is now available a reasonably proven method whereby an acceptable geological reconnaissance of the barren grounds of the Canadian .Shield within the Districts of Keewatin and Mackenzie might be completed within a decade. Thus, within a few years, it could place at the disposal of the prospecting and mining fraternity data which, by conventional methods, might not be made available to this generation. Due weight must be accorded this time factor when evaluating the aerial technique."

Jan 1, 1953

By P. E. Davidson

The management of solid waste is known to be a large and increasing problem in high-population areas throughout the world. It is not necessary here to add further definition to the nature and magnitude of the problem. Instead, it is the purpose of this paper to describe a new process, called the Andco-Torrax System, which will be of use in converting municipal solid waste into useful energy forms and a granulated slag by-product. The paper includes a description of the first commercial plant for the process.

Jan 1, 1977

By A Falter

Gyroscopic surveying instruments, which apply the physical law of a gyroscope, are being used for deter-mining the azimuth of lines with a high degree of ac-curacy. In the past ten years, gyro-theodolites have been introduced widely for underground orientation in the mining industry of Russia, Germany and South Africa. Gyroscorpic methods eliminate awkward procedures of conventional shaft plumbing, and provide more safety, excellent control and the highest precision at any point under-ground without interference with hoisting operations. The advantages of gyroscopic orientation in geodetic surveys become obvious in primary and secondary triangulation, in the determination of co-ordinates of single triangulation points, using the method of trigonometric re-section and intersection, and when traversing over long distances or in areas with obstructed view. Other fields of application are found in geophysical surveys and in the orientation of technical objects; e.g. radar stations, relay stations and ballistic missiles.

Jan 1, 1964

By T. Billotte, G. Tirand, J. Zollinger, V. Robin, B. Rouat, D. Daloz

The grain structure prediction of metallic alloys during a welding process is often an issue. In addition to the welding parameters and the alloy nominal composition and properties, the base metal grain structure and chemical homogeneity also play an important role in the formation of the final microstructure. In this paper intensive characterisation of solidification structure in gas tungsten arc welding of Ni base alloy 600 are described. It is shown that in transverse section of the weld, while the grain structure shows some texture following constrained solidification growth, grain density in the weld is similar or greater than grain density in the heat affected zone. This suggests that simulation of the welding structure needs, in order to be predictive, to take into account : epitaxial growth, secondary nucleation events and 3D growth inside the weld pool.

Jan 1, 2015

By F. Mohamm

"Recent changes in regulations and scientific advances concerning selenium bioaccumulation have placed greater importance on non-biological treatment systems for selenium control. Mining wastewater contains hexavalent selenium (selenate) as the predominant aqueous species and possibly small amounts of tetravalent selenium (selenite). Non-biological removal of selenite is accomplished readily and cost effectively by ferric co-precipitation and adsorption using ferric oxyhydroxides sourced from ferric salts or iron anodes in electrocoagulation cells. Selenate on the other hand is difficult to remove. It is often incorrectly assumed that electrocoagulation is suitable for removing both selenite and selenate. Selenate removal efficiency by electrocoagulation is low and the amount of waste residue produced high. In contrast, BioteQ’s Selen-IX™ process removes selenate very efficiently and produces a much smaller amount of stable residue. The process combines selective ion exchange with electro-reduction of selenate in electrocells that physically resemble electrocoagulation cells but are designed and operated differently. This paper summarizes four years of pilot scale demonstration on a wide range of mine waters and discusses the key benefits and limitations of Selen-IX™. The pros and cons of combining ion exchange with electro-reduction in comparison to direct electro-reduction of selenate are also reviewed.INTRODUCTION Selenium in Mining and Mineral Processing Effluents Similar to sulphate and metals, selenium presence in mining and mineral processing wastewater originates from minerals contained in the mined deposits. Therefore, no organoselenium species are typically present in these kinds of waters and inorganic species including selenite (SeO32-), selenate (SeO42) and elemental selenium account for the majority, if not all, selenium present in these streams. Elemental selenium is not always present in mine water but is often contained in smelter wastewater. To comply with new environmental regulations, a successful water treatment plant must remove selenium from all these forms effectively and economically without generating by-products that are difficult to dispose of or manage. Elemental selenium can be dealt with using filtration or gravity separation in clarifiers often assisted by flocculants and/or coagulants. Mine impacted waters typically contain other forms of suspended solids which are removed from water in this way. Once the solids are removed, the selenium species that remain untreated are the dissolved forms. In mining waters this is mostly selenate with small fraction of selenite. In smelter wastewater, the majority could be selenite. It is well established that tetravalent selenium is readily removed from water by using ferric iron co-precipitation at pH > 4 (NAMC SWG, 2010). Ferric hydroxide/ferrihydrite solids act as the adsorbent for tetravalent selenium when it is in one of the ionic forms of biselenite or selenite. This treatment for tetravalent selenium is highly efficient. Therefore, tetravalent selenium removal is generally not an issue and is often easily incorporated into lime neutralization or unit operations such as electrocoagulation used for removing other metals present in mine impacted waters. Another option of dealing with tetravalent selenium is sulphide precipitation in acidic pH which produces SeS2 and can separate selenite from other metals and/or sludge produced at neutral to alkali pH."

Jan 1, 2017

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"In January 1974, the Minerals Division of Canadian Occidental Petroleum Ltd. made the strategic decision to add uranium to its active exploration commodities and through compilation studies selected northern Saskatchewan as the most attractive and cost-effective exploration area in Canada. In August 1974, 100 sq. miles were staked adjacent to Gulf Minerals' Rabbit Lake deposit and east of the Esso Minerals Midwest boulder train. Initial exploration was based on geologic models of the Rabbit Lake deposit.In the summer of 1975, surface surveys delineated radon anomalies which were drilled that winter and found to overlie anomalous concentrations of uranium in the regolith which forms the upper unit of the crystalline basement. Within the crystalline basement, one hole intersected graphite and pyrite with anomalous nickel-cobalt-arsenic. Geochemical and radiometric surveys followed in the summer of 1976. Drilling in the winter of 1977 intersected several zones of graphite and also anomalous, but uneconomic, uranium abundances. Also in 1977, Dahlkamp and Tan (1977) described the coincidence of graphite and uranium at Key Lake and ground EM surveys on CanadianOxy claims detected graphite conductors beneath 250 ft of Athabasca sandstone. Inco Limited joined the project in April 1977 as a 50% partner. The project area was then surveyed using the airborne INPUT EM method, which detected 84 miles of conductors, with associated graphitic metasediments. On the ground these were located with MaxMin surveys, and follow-up drilling located the ""Tent"" Lake uranium zone.In 1978, the Midwest and Dawn Lake discoveries were announced, 7 miles and 2 miles west of the Joint Venture (J.V.) claims; and, in part for this reason, the 1979 winter drilling was concentrated on the deeper west side of the property. Exploration hole 102-79 intersected altered and uraniferous rocks, but stepout holes were barren. Drill hole 153-79 tested an under-snow three-station radon anomaly east of hole 102-79 and intersected 33 feet of 7.51 % U3O8, confirming the disco very of the McClean North zone. The geophysical grid of the McClean North conductor system was extended and detailed a strong, continous conductor to the south, called McClean South. This was drilled in January 1980and hole 1004-80intersected 22 feet of 2.95% U3O8."

Jan 1, 1983

By G. J. McTeer, D. L. Verhelst, D. J. Rioux

Teck Metals Ltd. operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Since 1997, KIVCETTM flash smelting technology has been utilized for the treatment of zinc plant residues and lead concentrates. Trail Operations’ furnace uses four water-cooled jackets for bullion tapping. This paper provides an overview of KIVCET bullion tapping for the past 16 years, and discusses successes and challenges encountered with respect to operations, training and monitoring.

Jan 1, 2015

By Z. Ren, M. Tomlinson, E. Asselin

"Organic carbon blinding is a common, yet often partial, solution to the reduction of preg-robbing. A quantitative method to assess the extent of adsorption of a given blinding agent is presented herein. The adsorption of several blinding reagents on various carbon samples is quantified using electrochemical impedance spectroscopy (EIS). EIS results showed that kerosene is more strongly adsorbed on carbon than sodium lauryl sulphate (SLS), while SLS can hinder the charge transfer process of the oxygen reduction reaction on the carbon surface more effectively. The effectiveness of SLS is pronounced when its concentration is higher than 100 ppm. Raman spectra are presented for selected carbon samples: as the area ratio of the disordered peak to the graphitic peak increases, blinding agent adsorption increases.INTRODUCTION The presence of naturally occurring constituents in gold ores may adversely affect the extraction of gold in cyanide leaching since the gold cyanide complex, Au(CN)2–, can be adsorbed by these constituents (M. Adams & Fleming, 1989; Afenya, 1991; Miller, Wan, & Díaz, 2005). Such ores are known as “preg-robbing”. Preg-robbing behavior may arise from natural carbonaceous materials in the ore (M. Adams & Burger, 1998). In the past decades, a number of pre-treating methods have been developed for refractory carbonaceous ores (Arriagada & Osseo-Asare, 1984; Beer, 1994; Dunne et al., 2007; Jiang, Liu, Xiao, & Yang, 2012; Kohr, 1997; Kulpa & Brierley, 1993; Menne, 1992; Menne & Revy, 1994; Moyes & Houllis, 2010; Petrie, Craw, & Ryan, 2005; Simmons, 1996). The method known as blinding is one of the most effective and economical pre-treatment methods (M. D. Adams & Burger, 1998; Albert, 1923; Darrow, 1924; McQuiston & Shoemaker, 1975; Van den Berg, 2000). Blinding, also referred to as blanking or passivation, uses a chemical reagent to passivate the preg-robbing carbon by selective absorption or wetting (Bas, Altinkaya, Yazici, & Deveci, 2012; Brierley & Kulpa Jr, 1993; Dunne et al., 2012; Van den Berg, 2000; Yang, Qian, Song, & Dong, 2013; Yen, Amankwah, & Choi, 2008; Zhou, Jiang, & Choi, 2014). Organic reagents, which selectively adsorb on the surfaces of activated carbon and “smother” the surface, have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Two comprehensive studies by Abotsi and Osseo-Asare and Adams and Burger have been published on this topic (Abotsi & Osseo-Asare, 1986; M. D. Adams & Burger, 1998)."

Jan 1, 2017

By C. A. Young, H-H. Huang, L. G. Twidwell

Equilibrium calculational software programs can be effectively utilized to model important parameters in aqueous and aqueous/solid systems, e.g., activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation. In this regard, the calculational program ST ABCAL will be demonstrated. Illustrative examples for the creation of diagrams such as potential-pH, and activity or concentration-pH will be presented to demonstrate the fundamentals in real hydrometallurgical systems. Speciation, titration and mixing will be used to simulate or predict operational processes. Berkeley Pit water from a flooded abandoned copper open-pit mine will be used to illustrate the modeling process. According to analytical results the water contains about 20 important constituents. In addition to measured potential and dissolved oxygen, there are two distinctive oxidation/reduction couples. Concentration and other experimental parameters are seldom matched to each other and 12 different conditions have been identified. Water for each condition must be speciated in order to find the best-fit model. The STABCAL program will be used for the modeling calculations and the implication of the water chemistry to defining treatment opportunities will be discussed.

Jan 1, 2005

By Zhong Zhang, Xijia Wu, Prakash C. Patnaik

"The integrated vehicle health management (IVHM) aims to provide life cycle management decisions for military platforms and their propulsion systems with reduced life cycle cost and increased operational readiness and safety. Among all the issues of IVHM, understanding the physics of failure and predicting lifetimes of the critical components are at the core: the decision makers have to know when and how components may fail in order to plan ahead. The difficulties to tackle failure problems lie in determining the material response to cyclic and dwell loading in a hot and/or corrosive environment, which all combined to induce multiple deformation and damage mechanisms, resulting in mix-mode failures. Decisions on component replacement (material substitution) and mission planning must be based on quantitative knowledge of the failure physics to mitigating the risk. This paper addresses the critical failure issues including creep, low cycle fatigue (LCF), thermomechanical fatigue (TMF); and presents a mechanism-based approach to life prediction. The mechanism-based approach, by its physics, is widely applicable over the entire operational spectrum of both structures and engines, and therefore is suitable for IVHM purposes."

Jan 1, 2015

By David A. Edgecombre

This paper discusses modern practices in the extrusion of steel. Particular emphasis is given to a description of the Ugine Sejournet method of extrusion, involving the use of glass as a hot work lubricant. Other methods are also mentioned. A brief history of extrusion is presented; present practices in the quality extrusion of tubing and solids are described; and the future potentials of the) process as a tonnage producer are briefly discussed. The advantages of extrusion and the reasons for the use of a glass lubricant, as well as the various methods of using glass, are given. The process, as described, is being used in the manufacture of large commercial quantities of stainless steel tubing and sections. This extrusion process is an essential and unique means of forming such atomic-age materials as titanium, zirconium, molybdenum and other super alloys all of which are materials required in the creation of nuclear installations.

Jan 1, 1963