Search Documents

By D. B. Haas

THE HYDRAULIC TRANSPORT of solids is becoming increasingly prevalent throughout the world. Major long-distance slurry pipelines currently in operation transport commodities such as coal and various ore concentrates distances of up to hundreds of miles. In the United States, a number of large-diameter, high-tonnage pipelines are under consideration for the transport of Western Plains coal to markets up to 1000 miles away. In these and other applications, the solids are generally quite fine, with 14 mesh being a typical limit of particle size for long-distance (over 100 miles) slurry transport. There are applications where it might be practical to transport solids consisting of larger particles distances of up t o 100 miles. Deposits of high-quality metallurgical coal are found in the inner foothills belt along the eastern edge of the Rocky Mountains on the Alberta-B. C. border. There are few existing railroad s and the possibilities of constructing extensions are limited because of environmental and economic factor s. In these circumstances, the most efficient transportation system might consist of a pipeline to transport the coal from the mine to beneficiation plants located near existing railroads 50 or 100 miles away. Such systems would minimize environmental effects, capital cost s and operating costs. To determine whether such a system would be technically feasible, experimental testing is needed to determine the energy requirements for transporting coarse coal in a pipe line. Currently, run-of-mine metallurgical coal is crushed to less than 1 1/2 inches before going to the beneficiation plant. In the proposed scheme, coal of this size would be transported through a pipeline to the beneficiation plant located at the railroad. The Transportation Development Agency and the Department of Supply and Services have awarded a contract to the Saskatchewan Research Council to study pipelining of coarse coal in pipelines ranging from 4 inches to 12 inches in diameter.

Jan 1, 1977

By A. M. Elmahdy, T. Hirajima, M. Farahat

"Separation of molybdenite from chalcopyrite is mainly achieved through flotation technique to raise their grades up to 25% to be extracted in smelters. However, molybdenite recovery and grade obtained from this process is not satisfactory in most cases due to the natural hydrophobicity of both minerals. The influence of conventional heat treatment on pure chalcopyrite and molybdenite minerals was investigated. X-ray diffraction, TG-DTA and XPS techniques were applied before and after heat treatment. The results showed phase changes for both minerals. Magnetic separation experiments of single and mixture of both minerals at several magnetic intensities were made. For single mineral experiments, 100% molybdenite recovery was obtained at all experimental conditions as non-magnetic fraction whereas ca. 100% chalcopyrite recovery was achieved under certain conditions. In case of 1:1 binary mixture, 87% and 83% molybdenum and copper recoveries, respectively, were obtained. The increase in chalcopyrite magnetic recovery is related to the formation of more magnetic phases as confirmed by characterization techniques.The objective of this study is to increase the magnetism of chalcopyrite to make its separation from molybdenite by magnetic separation possible and to understand the mechanism behind it. These results indicate that it may be possible to upgrade molybdenite ores using heat treatment followed by magnetic separation to the required grade by smelters which is difficult to attain by froth flotation and the other techniques."

Jan 1, 2016

By Walter Koellner

Today?s large electric mining shovels are significant users of power and represent peak loads of more than 3.5 MW to a mine?s distribution system. The power swings during normal operation can influence the line voltage at the Point of Common Coupling (PCC). The static converters for the shovel?s motions also create voltage and current harmonics which are fed back into the mine?s power grid. In addition, shovels themselves are affected by the power quality of the mine?s distribution system. This paper introduces the use of active IGBT rectifiers, also called Active Front Ends (AFE), as alternative to conventional, line commutated SCR thyristor rectifiers. The AFEs convert the AC line input into a controlled DC-link voltage. This DC voltage is then used as input to IGBT inverters, which power the AC motors of the shovel?s Hoist, Propel, Crowd, and Swing motions. The introduction of AFEs creates the following operational improvements: i) reduction of the Harmonic Current Distortion THDi from more than 40% to less than 4%; ii) full regenerative operation; iii) the potential for line voltage stabilization at the PCC; iv) high tolerance for line voltage fluctuations; v) improved dynamic performance, and, as result vi) higher availability and productivity of the shovel.

May 1, 2001

By V. ?. Chanturiya, I. Zh. Bunin, M. V. Ryazantseva

"Surface changes in naturally occurring metal sulfides (pyrite, arsenopyrite, sphalerite, chalcopyrite, galena, and molybdenite) due to treatments from high-power electromagnetic pulses (HPEMP) at varying times were studied using X-ray photoelectron spectroscopy. Analysis of the obtained results revealed common patterns and differences in surface transformations. The transformations were found to include two main stages. The first stage was observed at low treatment intensities (up to n ~103 pulses). At this stage, formation and accumulation in the surface layer of the nonstoichiometric sulfide phase, oxides and hydroxides, as well as elemental (polysulfide) sulfur and/or metastable sulfur species (thiosulfate, sulfite) was observed. The second stage (N = 3·103 pulses) is characterized by thermal removal of sulfur species and renewal of the mineral surface (sulfidization).It was found that the chemical changes of the sulfur on the surface layer of pyrite, arsenopyrite, chalcopyrite included accumulation/formation of S0 (Sn 2-) at the first stage of the transformation, followed by its removal. An increase in the surface concentration of elemental sulfur for pyrite and chalcopyrite was 10–12% while arsenopyrite was approximately 5%. A more complicated chemical change was observed for sphalerite and galena, that included formation/accumulation of metastable sulfur species (thiosulfate, sulfate) at the initial stage (up to 103 pulses) and during longer treatment times, the sulphur is reduced back to its initial state (sulfide or disulfide). The increased concentration of S0 sulfur, compared to the original sample, was only 3% in galena and sphalerite.The application of HPEMP treatment to improve flotation selectivity is supported by singlemineral flotation tests. Changes in flotability as a result of HPEMP treatment are principally explained by surface phase changes that resulted in higher adsorption activity."

Jan 1, 2016

By H. N. Tran, D. Barham

"A systematic survey of the appropriate literature in terms of phase equilibria and possible reactions involving deposits in Municipal Solid Waste (MSW) incinerators are analyzed particularly with respect to the theoretical first melting points of typical ashes and the possible presence of a liquid phase at the temperature of ash-metal interface. Conclusions are drawn on the basis of the possible presence or absence of various metal chlorides and sulphates in such situations, and their effects on the problems of fouling and metal corrosion. From preliminary results, it would appear that ZnCl2 is unlikely to be present in any molten phase which causes corrosion because it evaporates rapidly from such liquids. It would also appear that PbCl2 and, by inference, ZnCl2 will sulphate at relatively low temperatures if the flue gas contains SO2 and O2.IntroductionMunicipal Solid Waste (MSW) incinerators produce fly ash which deposits on heat transfer surfaces throughout the furnace, leading to corrosion and loss of energy recovery efficiency. Despite a massive amount of research carried out on the subject of corrosion in MSW incinerators, the problem of corrosion of heat transfer metal is still with us, and no definite over-all cause and effect relationship has yet been identified. In order to make a contribution to the eventual solution of this problem, the authors have examined the problem from the beginning, using their knowledge of fouling and corrosion problems in black liquor recovery boilers as a starting point.The incineration of MSW has been used for many years to reduce the volume of material sent to landfill (ash volume compared to raw waste volume), and, in most cases, to recover energy at the same time by raising steam The steam may be ""low- or high pressure/ temperature"" depending on its end use. The higher the steam pressure and temperature, the greater seem to be the problems with corrosion of heat exchanger metal, presumably because the metal must withstand higher surface temperatures.The chemical and physical composition of MSW is extremely variable, not only on a regional basis, seasonal basis, and day-today basis, but also on a minute-by-minute basis, due to the inhomogeneity of MSW. This makes it extremely difficult to define cause and effect relationships, because both cause and effect are transient in nature."

Jan 1, 1991

By A. Dahi Taleghani, Amir Shojaei

A continuum damage mechanics (CDM) based constitutive model has been developed to describe elastic, plastic and damage behavior of rock during drilling. In addition to inelastic deformations, this model incorporates rock anisotropies like toughness anisotropy due to the bedding planes orientation that is a common observation in soft Shales. The pressure sensitive inelastic deformation of porous rocks together with their damage mechanisms are studied for drained and undrained conditions. Fracture mechanics of microcrack and micro-void nucleation and their coalescence are incorporated into the formulation of the CDM models to accurately capture different rock failure modes. The performance of the developed elastoplastic and CDM models are compared with the available single cutter test data of a specific shale play and then the models are introduced into a commercial finite element package through user-defined subroutines. A workflow to derive the required model parameters is presented through inverse modelling of the single cutter test data. The developed CDM model outperforms the traditional discrete element and fracture mechanics approaches by removing stress singularities at the fracture tips and simulation of progressive fractures like formation of the cuttings ribbon without any essential need for remeshing. This model would provide a robust tool for modeling bit performance and rate of penetration using conventional elements of FEA with a reliable results and a computational cost less than similar computational techniques like discrete element methods.

Jan 1, 2015

By Elaine Ellingham, Francis T. Manns

"The Orostar and Scadding were two small gold mines owned and operated by Orofino Resources Limited. Conventional statistical treatment indicates an identical arithmetic mean grade of 0.22 oz/T Au for both mineable reserves. Further, the deposits are both shown to have cut weighted average reserve grade of 0.21 oz/T. Orostar mined out at 0.206 oz/T and Scadding at 0.156 oz/T Au. The combined exploration and development database contained 1394 fire assays, more than enough for statistical confidence in a normal distribution. Therefore this study was initiated to determine, if possible, why the mill head grades were lower than the averages and to experiment with several methods to determine whether a reliable statistical mill head grade estimation method would emerge. Despite the identical reserve grades, distinct differences in the grade distribution histograms are present. By studying the arithmetic and log-normal grade distributions, with some attention to South African practices, this paper reports on those differences which may account for the considerable divergence in the mill head grades. Furthermore, this study casts considerable doubt on the industry standard method of cut weighted averages.The global mill head grades of the two deposits have been derived from the arithmetic average grades by graphic means. This precise method of mill head grade prediction, if applied to complex orebodies, could permit selective grade control and result in direct cost savings by allowing the operator to detect false value stopes, benches or levels and emphasize reliable regions of not only gold mines, but also uranium or base metal deposits."

Jan 1, 1992

By B. Dyck, C. Rodgers

ABSTRACT Cameco Corporation is revitalizing its Key Lake Operation uranium mill in northern Saskatchewan. The mill currently uses ammonia stripping in solvent extraction (SX) and ammonia yellowcake precipitation. As part of the revitalization, the company considered installing strong acid stripping in solvent extraction (used at its Rabbit Lake Operation), which would lead to using hydrogen peroxide for uranium precipitation. As part of the process evaluation, tests were carried out to study how the drying temperature in indirect fired dryers would affect the uranium peroxide yellowcake precipitate properties. This paper discusses the test work results, including the relationships between drying temperature and product reactivity with water, product colour, product grade, and energy input requirements.

Jan 1, 2012

By A. D. Pittuck

Refractory minerals .containing uranium and columbium have been successfully treated at Queen's University, Kingston, to produce high-grade concentrates. Recoveries of over 90 per cent of the uranium and columbium have been obtained when treating concentrates containing euxenite, fergusonite, betafite, and pyrochlore. The processes ?consisted -of leaching the columbium with hydrofluoric acid, and the uranium with nitric acid, sulphuric acid, or sodium carbonate solutions. The leach liquors were extracted with organic solvents from which the values were stripped and precipitated, producing final products assaying 45 to 55 per cent Ob2O5 and 60 to 70 per cent U3Os.

Jan 1, 1958

By Lynn I. Kelley

Potash is the primary industrial mineral produced in Saskatchewan, followed, in terms of gross value, by aggregate, sodium sulphate, salt, potassium sulphate, peat, clays, silica sand, calcium chloride brine and "clinker." Potentially economic deposits of kaolin, diamond and building stone are under evaluation.

Jan 1, 2001

By M. J. Nicol, T. Moyo

Ammoniacal solutions are an effective lixiviant for the oxidative dissolution of some mineral sulphides. A detailed study of the anodic dissolution of chalcopyrite in ammonium sulphate-ammonium hydroxide solutions has been carried out using cyclic voltammetry, chrono-amperometry and rest potential measurements. The role of the copper(II)/copper(I) redox couple in the oxidation process has been evaluated. Rest potentials have been found not to be affected by oxygen but to increase with an increase in initial copper(II) concentration. Pseudo-steady-state anodic current densities measured in the absence of copper(II) ions at the rest potentials obtained in the presence of copper(II) ions increase with increasing concentration of copper(II) ions, confirming the positive effect of copper(II) ions on the rate of dissolution of the mineral. Cyclic voltametric and chrono-amperometric data show that in the absence of initial copper(II) ions, the rate of dissolution in the presence of dissolved oxygen is significantly lower. These results confirm that the effective oxidant for the mineral under the conditions of the study is copper(II) and not dissolved oxygen. Coulometric measurements have been used to establish the stoichiometry of the anodic reaction at different potentials.

Jan 1, 2014

By John R. Hayes, Kebbi A. Hughes, John Rowson, Peter E. R. Blanchard, Jeremiah C. Beam, Andrew P. Grosvenor, Arthur Situm

Uranium ore bodies contain elements within mineral phases that need to be disposed of responsibly. Solid waste can be placed in a tailings management facility (TMF) to contain the waste elements and limit interactions with the environment. It is important to understand how the chemistry of the tailings evolves throughout the lifetime of the operations that feed the TMF and after the site has been decommissioned. The objective of our collaboration with Orano Canada was to study how the tailings from the TMF located at McClean Lake, Saskatchewan change over time. This manuscript discusses our use of X-ray absorption spectroscopy (XAS) and X-ray microprobe to study the fate of Mo and Ca in the tailings. Mo is considered an element of concern (EOC) and it is necessary to determine if a stable solid Mo-bearing species forms. Thermodynamic modeling suggested that aqueous Mo would precipitate over time as powellite (CaMoO4). Comparing Mo K-edge XAS spectra from the solid tailings to the aqueous Mo concentration in the pore water showed that powellite did form and that this did result in a decrease in the aqueous Mo concentration over time. Further, it has been proposed that Ca2+(aq) can react with bicarbonate ions in the pore water and precipitate as calcium carbonate (e.g., CaCO3). This reaction would limit the aqueous bicarbonate present in the tailings that could react with uranyl ions to form soluble uranyl-carbonate complexes. We have identified several trace Ca-bearing species, including carbonates, in the tailings using XAS and X-ray microprobe.

Jan 1, 2020

By W. Dietzel

Fracture mechanics based techniques are used to gain insight into the phenomenon of stress corrosion cracking (SCC) and to develop guidance for avoiding or controlling SCC. From constant extension rate experiments under rising load or rising displacement conditions the susceptibility of high strength steels, aluminum, magnesium and titanium alloys to SCC and hydrogen embrittlement can be assessed. Such tests on pre-cracked specimens are also well suited for studying the mechanisms leading to SCC by employing appropriate models for the degradation of metallic materials which take into account the uptake of atomic hydrogen from the corrosive environment. Measurements of crack growth resistance curves using the crack tip opening displacement as fracture parameter can be compared with simulated R-curves obtained from modeling of the mechanism of hydrogen embrittlement. The materials investigated are a high strength steel and a magnesium alloy both exposed to environmental conditions which fostered the uptake of hydrogen.

Jan 1, 2010

By D. C. Carter, J. P. Anderle

"Exploration drilling of evaporite sequences in eastern Canada has undergone significant changes in equipment, techniques and philosophy since the early 1970s. The result has been the recovery of full-size cores from properly conditioned and stabilized holes, high quality open hole geophysical logs, and high quality metallurgical samples. The majority of modifications have resulted from the necessity to preserve the integrity of the evaporite deposit, and thus ensure the potential development, combined with the need for cost-effective high quality information. This is particularly evident in the priority placed on the development of non-erosive drilling fluids, casing and cementing procedures. The results are applicable to diamond drilling exploration of evaporite deposits anywhere in the world.IntroductionThe majority of current technical and scientific literature and expertise available on such subjects as drilling fluids or cementing procedures is applicable to large diameter, deep (several thousand metres) oil-field type drilling . The differences between oil-field drilling and wire-line core diamond-drilling are dramatic: large diameter, deep holes drilled with a low rpm tricone bit using large volumes of fluid pumped through a large annulus versus small diameter, shallow (less than 600 m) holes drilled with a high rpm diamond-set core bit using small volumes of fluid pumped through a small annulus. Exploration drilling of evaporite sequences in eastern Canada in the early I970s was conducted using oil-field equipment and techniques to complete holes of moderate (1000 m to 1500 m) depth . The prohibitive cost of these operations has necessitated that subsequent exploration drilling employs modified diamond-drilling equipment and techniques developed as part of a transition away from oilfield methodology. The result has been full size core, recovery approaching 1000/0 and the ability to run open hole geophysical logs; a combination of factors enhancing the collection of high quality information (Carter, I989a)."

Jan 1, 1990

By Young Hyun Paik, Hyung Sup Choi, Yeun Sik Kim

The basic studies on the surface properties and flotation characteristics of ilmenite were made by electrophoretic, adsorption, contact-angle and floatability measurements. The isoelectric point of ilmenite is found to be at pH 5.6. By combining the results of electrokinetic studies and adsorption measurements, a clearer picture of the ilmenite-solution interface was observed. These findings were correlated with the floatability of ilmenite obtained by Hallimond tube tests. The general flotation characteristics of ilmenite are compared with those obtained for magnetite and rutile. It is indicated that the above three minerals, namely, ilmenite, magnetite and rutile, have very similar surface properties and flotation characteristics. Therefore, it is difficult to make an effective separation of these minerals by flotation. However, it is found that sodium orthophosphate acts as a selective depressant for magnetite in anionic flotation. Therefore, close pH control of the pulp in the presence of the phosphate ion enhances the possibility for a successful separation of these minerals.

Jan 1, 1967

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010

By D. Satish Kumar, D. Mazumdar

"95% bulk mixing times in three different size water model ladles of a 140 T cylindrical shaped , dual plug ( located diametrically opposite at mid bath radius position) stirred, industrial ladle were determined experimentally with and without an upper buoyant phase. Based on dimensional analysis and a regression of the experimental data and, it was shown that in the inertial and gravitational force dominated flow regimes, 95% bulk mixing times for a slag-less situation can be described via:[equation]Parallel to this, a large number of experiments were also carried out in one of the water models (D=0.30m) to quantify the influence of an upper buoyant phase on mixing. These indicated that mixing time, operating variables and thermo-physical properties of the upper phase liquid can be correlated via a dimensionless relationship of the type:[equation]in which, Q is the ambient gas flow rate, L is the depth of liquid , (AL) is the slag layer thickness and 6 and t are respectively the surface tension and viscosity of the upper phase fluid The dimensional analysis, regression of experimental data as well as the adequacy of the proposed correlations are discussed in the text."

Jan 1, 2004

By Gae On Kim, Ki Baik Kim, Suk Hoon Kang, Tae Kyu Kim, Sanghoon Noh

"Advanced radiation resistant oxide dispersion strengthened steel (ARROS) is being developed as a fuel cladding tube material for future nuclear reactor system applications. The research activities consist of advanced radiation resistant ODS steel development and fabrication technology development of ODS steel structural components. One candidate material with a chemical composition of (in wt%) Fe-10Cr-1Mo-0.5Mn-0.1V-0.25Ti-0.35Y2O3and was selected as representative materials, and this material was named as the advanced radiation resistant ODS steel (ARROSTM).On the basis of this ODS steel composition, an optimized fabrication process of structural components such as plates, sheets and tubes has been established through various process conditions in mechanical alloying, hot/cold working, and heat treatment processes. These R&D activities are expected to contribute to the realization of ODS materials in the future.INTRODUCTIONA sodium-cooled fast reactor (SFR) is being developed at the Korea Atomic Energy Research Institute (KAERI) with a view to economics, safety, reliability, and sustainability. The prototype Gen-IV SFR with a capacity of 150 MWe is under design, and this prototype reactor is scheduled to operate from 2028. For a commercial SFR system application, it is necessary to develop an advanced structural material having both high creep strength and irradiation resistance at high temperatures (Jeong, 2014). Oxide dispersion strengthened (ODS)steel is one of the most promising structural materials because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density, which is extremely stable at high temperatures under a neutron irradiation environment for a prolonged operating period(Kim, 2016). As the first step, several batches of ODS steel were designed and the candidate samples with a 2 kg scale each were fabricated by mechanical alloying, hot isostatic pressing and hot rolling processes. The mechanical properties of these samples were evaluated. Up to now, two candidate materials with chemical compositions of (in wt%) Fe-10Cr-1Mo-0.5Mn-0.1V-0.25Ti-0.35Y2O3 was selected as representative materials, and these materials were named as the advanced radiation resistant ODS steel (ARROSTM).The next step was to optimize the fabrication process of the ARROS compositions for in-core structural components such as the fuel cladding tubes of a SFR. An optimized fabrication process of fuel cladding tube with a composition of ARROS has been established through various process conditions in mechanical alloying, hot consolidation, hot/cold working and heat treatment processes. Joining technologies of the ODS steel tubes is being developed using solid-state welding such as magnetic pulse welding, friction stir welding and diffusion boding. It is expected that the development of ARROS will contribute to the realization of a commercial SFR with high economics and sufficient safety in the future. In this paper, the study of fabrication process of ARROS structural components is introduced."

Jan 1, 2017

By Greg Gosson

These materials are provided for general information purposes only and do not constitute legal advice. Readers are advised to seek specific legal advice from their own counsel in relation to any decision or course of action contemplated. Outline ??What is meant by a ?current technical report? under NI 43-101? ??When is a current technical report required? ??Who makes the decision regarding whether a technical report is current? ??Examples of the types of information that make a technical report no longer current for securities filing purposes.

May 1, 2009

By H. Arima

The Akita Zinc Company is the only refinery which produces hematite from the iron content in the zinc leach residue. The Akita Hematite Process consists of five stages, which are SO2 pressure leaching, the first neutralization stage, the de-arsenic process, the second neutralization stage and pressure hematite precipitation. In order to strengthen its cost competitiveness and stabilize its operation, the Akita Hematite Process has been modified continuously. Most recently, two process modifications were carried out. The first was an improved ability to maintain a lower arsenic concentration in the de-arsenic process, and the second was an increased throughput in the hematite precipitation autoclave. The details of these recent changes in the Akita Hematite Process are presented in this paper.

Jan 1, 2006