Search Documents

By Peter Clevenstine

Minnesota Iron Ore Trifecta 1. World Demand 2. Industry Consolidation 3. Competitive Advantages

May 1, 2011

By H. Soto, P. Lacombe, R. del Villar

"During the summer of1989, Les Mines Selbaie, with the cooperation of Université Laval initiated a research project to evaluate the column flotation technology for its concentrator near Joutel, Quebec. The experimental work involved both a 5 cm by 11 m laboratory column and a 45 cm by 10 m home-made pilot unit Amenability tests were conducted using both units on various streams of the plant. Results showed that columns are not suitable for the copper cleaning circuit because the loss of precious metals, associated with the rejected pyrite, overcome the improved copper metallurgy. On the other hand, column testing at the zinc circuit showed improved zinc selectivity.Scale-up testing was', therefore, conducted on the first zinc cleaner concentrate using the laboratory-size column. The influence of variables such as porous parger grain size, wash water flow rate, airflow rate and froth depth values on column performance was' first assessed. Scale-up parameters were then determined using the optimal operating conditions from the previous tests. Simulation facilitated the determination of the most convenient plant-scale column arrangement.A number of conclusions concerning the experimental determination of scale-up parameters are also presented."

Jan 1, 1993

By M. Pelser, H. Gous, J. H. W. M. Brits, K. Voogt

The effect of impurities; iron and selenium, on current efficiency and deposit quality in copper electrowinning was investigated using an at-line cell at the Rustenburg Base Metals Refiners’ Copper Tankhouse. The tankhouse is a direct leach, starter sheet electrowinning operation with a unique electrolyte composition. The effect of iron on the current efficiency in the at-line cell was found to be less severe than reported in literature. However, the distinction between the chemical impact of iron on current efficiency and the physical impact of iron on a starter sheet operation needs to be realised. The effect of selenium on current efficiency and deposit quality is also reported. INTRODUCTION Anglo American Platinum’s Rustenburg Base Metals Refiners’ (RBMR) Copper Tankhouse serves a unique function in the refinery flowsheet in that its primary functions are the removal of copper and production of acid for the leach circuit. This function needs to be performed to specification in order to keep the leach circuit operating optimally. Current efficiency is seen as an indicator of tankhouse performance and efficient energy use. The tankhouse plates starter sheets onto titanium blanks which, after stripping and preparation, return into the production cells for further plating. Approximately 78% of tankhouses surveyed (Robinson et al., 2013) use permanent cathode technology whereas older, smaller operations still use starter sheet technology. Drawbacks of the starter sheet technology are that the starters are thin and bend easily leading to increased shorts, they need to be removed after two days of plating to be manually straightened and are then returned to the cells. In addition, the electrolyte levels in the cells need to be adjusted during the plating cycle to improve loop adhesion to the cathode and reduce loop corrosion. The starter sheet technology is therefore very labour intensive and the final quality of the product is dependent on the quality of the starter sheets produced. In comparison, permanent cathode or direct plating technology lends itself to automation, allows for higher current densities and better cathode quality due to more robust geometric stability in the cell. The present barrier to implementation of permanent cathode plating at the RBMR Copper Tankhouse is the capital cost required to convert the tankhouse, i.e. blanks and stripping machine. At present, alternatives to titanium blanks, such as LDX 2101, are being investigated for the unique electrolyte composition of this tankhouse.

Jan 1, 2019

By R. W. Zeindler, D. A. Fawcett

"A summary is presented of the report completed by the Coal Mining Research Centre in 1980. This report was of a cross-pit conveyor system applied as an auxiliary mining complement to the major stripping unit, a dragline. The purpose of the CMRC report was to evaluate selective mining and replacement of the upper horizons of the strata as an aid in reclamation. These strata were the topsoil, subsoil and glacial till.Past utilization of cross-pit conveyor systems and related engineering studies were assessed. The parameters of the study were based on the mining and geological conditions of the Alberta prairie coal mines. The principal excavator for stripping was a dragline. Excavation of the upper horizons was done by a bucket-wheel excavator discharging onto the crosspit conveyor. Alternative equipment applications were economically compared. Four cases or geological sections were evaluated in detail. The economics of the alternative mining systems for each of the cases were determined. In all instances, the most economical solution was a tandem system utilizing a dragline with a bucket-wheel excavator/ cross-pit conveyor system."

Jan 1, 1981

By R. A. Horn, S. M. Telfer

"Canada has a per capita GDP second only to Japan among the G7 countries and a positive trade balance which ranks third among the world's major economies. International trade represents a very large part of the national economy and as a proportion of GDP is larger than that of all the other G7 countries with the exception of Germany. On the negative side the Canadian current account deficit relative to the size of the economy is significantly worse than that of all major industrial countries, due mainly to the cost of servicing an immense foreign debt and to a large and worsening negative trade balance in manufacturing.The outflow of money may be reduced by increasing the productivity and competitiveness of those sectors of the economy in which Canada already has a leading competitive position and which have the potential for further growth. The mining industry is uniquely qualified in this respect in that Canada is the western world's largest producer of metals and mineral products and has the geology and the exploration skill to replenish reserves assuming that an adequate level of investment is maintained. In 1989 the minerals industry contributed $8 billion to the country's balance of payments and with the exception of forestry is the only sector of the economy which has shown consistently increasing foreign earnings over the long term.In recent years there has been a decline in exploration in Canada and a significant increase in countries such as Chile. The demand for hard currency to finance the development of the newly emerging capitalist economies of the CIS and Eastern Europe is also driving these countries to seek foreign investment to allow them to exploit their natural wealth more efficiently. Canada is therefore facing growing international competition for risk capital and in the future its trade surplus will probably decline in the face of lower cost foreign production.Canada rightly exercises a high level of environmental control on its mining operations; however a significant deterrent to investment is the fundamentally unjust application of the many provincial and federal environmental laws, under which a mining company, even if it takes every measure to protect the environment, runs the risk of eternal and unlimited future liability. If this situation is not rectified the effect will be an increase in global pollution as mines in countries with more lax application of law and regulations controlling environmental damage replace those of Canada. Tax benefits and incentives are a more efficient means than arbitrary regulations in minimizing environmental damage."

Jan 1, 1994

By R. H. McCorkell

Measurements of radon in air and aqueous solutions can be affected by leakage from vessels in which samples and standards are kept and by absorption and later release of radon by the materials of these vessels. The author had received various oral communications concerning the se processes : e.g ., that natural rubber and greases absorb large amounts of radon, whereas silicone rubber and grease do not; and that radon is readily lost from polyethylene bottles and that inverting glass bottles containing aqueous samples reduced radon loss from them . However, the results of actual tests and quantitative data showing these effects were not available. For this reason, it was necessary to make numerous measurements of the leakage and absorption of radon in the course of designing apparatus and methods for measuring radium and radon concentrations. It was thought that the data obtained might be of use to others, and consequently they are compiled in the present note .

Jan 1, 1980

By J. Ling, J. Xiao, A. R. Laplante

"The most challenging gold gravity separations occur when gangue has a high s.g., gold is fine, or a combination thereof This paper examines such separations, and evaluates the performance of a 3-in Knelson Concentrator at various rotation speeds, a 4-in SuperBowl, and a laboratory Mozley Multi-Gravity Separator (MGS). Synthetic feeds, primary cyclone underflows and flash flotation concentrates are tested.It is concluded that higher rotation speed are mostly useful for very fine (< 3 7 µm) gold recovery, with potential loss of recovery in the 37-212 µm range. This problem is traced to the collapse of the flowing film at higher Gs, which hinders the percolation of particles of intermediate size. Increasing fluidization water flow can alleviate this problem, but the recovery of very fine particle then drops. The MGS does not operate with the same principles, and can achieve good to very good recoveries of very fine to fine gold particles, but the unit has a high cost to capacity ratio, and there is no evidence yet that it can yield smeltable concentrate grade or a concentrate that can be upgraded with a shaking table.IntroductionThis presentation is a sequel to similar CMP presentations of the past eight years; all focused on practical aspects of gold recovery. The first hard rock application of the Knelson Concentrator (Laplante et al, 1990), studies of the grinding and classification behaviour of gold and other malleable metals (Banisi et al, 1991; Laplante et al, 1995), the development of a 3-in Knelson based methodology to study gold gravity circuits (Laplante and Shu, 1992), a comparison of the Knelson and Falcon (Laplante, Laplante et al, 1993), the presentation of a test to determine the amount of gravity recoverable gold, or GRG (Laplante et al, 1996), and the use of synthetic materials, in particular tungsten, to mimic gold (Laplante et al, 1995) were presented. A summary of many practical implication of the McGill research was presented in 1994 (Laplante). Whereas gold gravity recovery was less popular and largely jig-based (in North America) at the beginning of the eighties, many gold plants now incorporate a gravity circuit, and the Knelson Concentrator is the most commonly used unit."

Jan 1, 1998

By Hoeve. J.

"In the unconformity-type uranium deposit at Midwest Lake, mineralization is associated with extensive host rock alteration, which affects the metamorphic basement as well as the overlying Athabasca Group sandstones. Host rock alteration is manifested by (I) transformation of clay minerals [kaolinite into illite and chlorite (sudoile)]; (2) bleaching due to removal of hematite from the lateritic paleoweathering profile and the overlying red bed, Athabasca Group sandstones; (3) loss of coherence of the sandstone resulting from corrosion of quartz cement; and (4) in the immediate vicinity of high-grade ore, development of a clay envelope due to residual enrichment of clay minerals caused by massive dissolution of quartz. Clay mineral transformation and bleaching are the most prominent and the most widespread alteration effects, forming haloes that extend for several kilometres along the strike of the mineralized structure and also constitute distinct alteration pipes that rise f or several hundred metres above the unconformity to be truncated at the present top of the bedrock.Although the two haloes are largely congruent features, cross-culling relationship s indicate that clay mineral alteration represents an earlier phase in the history of the deposit than the large-scale bleaching that gave rise to the superimposed bleaching halo.Because clay mineral alteration and bleaching are intimately tied to the mineralization and extend well beyond the limits of the actual orebodies, host rock alteration may be used as an ore guide in exploration and drill-hole evaluation. In this application a third hydrothermal discharge centre was identified, as yet untested for are, which is located between the hydrothermal centres associated with the two known orebodies of the deposit.It is estimated that host rock alteration may enlarge a potential drill-target by a factor 10 - 20X. Information on the configuration of bleaching haloes can be obtained from systematic core logging, whereas diagnostic clay mineral alteration is readily identified by means of automated, quantitative XRD techniques."

Jan 1, 1984

By T. Kho, W. Zhang, M. E. Reed

The control of flash furnace heat balances is critical. Suspension smelting control and stability comes from stable operation of the heat balance, and this leads to a stable reaction shaft exit temperature. A number of flash furnace operations have been reviewed to determine if the application of this approach is beneficial for their operation. The cause and effect relationship between reaction shaft exit temperature with uptake and throat buildup is being enhanced with this work program. Our operating personnel are exposed to the operational hazards of cleaning this buildup from the throat and it is imperative that as an industry we continue to look for repeatable solutions. WorleyParsons has reviewed operational data from a number of flash furnaces and looked at the possible improvements that can be made to decrease variation in the reaction shaft exit temperature. The data assessed for each operation illustrate the need to fully understand the process inputs to the particular operation and to ensure that the control changes are correctly impacted. In the plant data that have been assessed for a number of operations combinations of feed changes and inappropriate process decisions have lead to changes in reaction shaft exit temperature which impact the overall furnace operation and the uptake shaft condition, and ultimately the boiler. INTRODUCTION In 2016 WorleyParsons jointly prepared a paper outlining the effects of heat balance control on the Olympic Dam flash furnace (Reed et al, 2016). That paper investigated the importance of heat balance control in flash furnaces and demonstrated the changes made at the Olympic Dam operation to control the heat balance in the furnace and the impact that change had. The operation is still using the tool to assist in trouble shooting performance and pinpointing problems that may lead to issues in the furnace throat and Waste Heat Boiler (WHB). As a result of the interest in the methodology and due to the issues surrounding safety and process performance caused by WHB throat buildup and damage, WorleyParsons approached a number of flash furnace operators to discuss the application of the approach at their operations.

Jan 1, 2019

By Z. Abbasloo, A. Masoomi, L. Ebrahimi, A. Mortazavi, A. Keshavarz

"Investigation and 3D analysis of Heap no. 2 of Meydook copper complex was the subject of this study. In this project all geological and geotechnical investigations conducted in the mine were evaluated aiming at determination of Heap no. 2 design parameters. The main objective of the project was to evaluate the potential for construction of Heap. No. 2 on a waste dump built in a valley in the north side of the pit.Considering the space limitation for dump location this was a viable alternative to reduce the costs associated with heap no. 2 construction. Moreover, it allowed for a significant reduction in overall mining costs. Considering the project condition, a 3D analysis of heap major structures including; valley rock foundation, waste dump, and low grade ore was carried out. Five sets of analyses were conducted and the displacement and stress fields were calculated within the heap no. 2 components. In all analyses conducted the subsident profile was determined for the valley base rock and heap foundation (waste dump). Moreover, the shear interaction between heap and waste dump was evaluated at the heap interface. The analyses results showed that the maximum settlement at the heap base is about 4-5 cm and the waste dump provides a safe and reliable base for heap construction. Moreover, the analysis results showed that the selected %5 grade for the heap interface is good and does not pose any risk in terms of heap Interface shear displacements. A sensitivity analysis of heap mechanical parameters was also conducted. The obtained results show that if the friction angle of heap material is reduced below 25 degree due to acid spraying process, the heap walls become unstable and the heap geometry must be redesigned."

Jan 1, 2015

By Yi-xin Zhoa

The characteristics of coal bumps are analyzed based on the microseismic data from No.8935 workface in Xinzhouyao coal mine, Datong Mining Group. The geology of this workface is characterized by the thick sandstone roof and coal seam, both with relative higher stiffness and strength. In order to investigate the mechanism and precursors of coal bumps occurred in No.8935 workface, the locations of microseismic, the relationship of microseismic energy and frequency and the spectrum of microseismic signals are analyzed. The result shows that the coal bumps in No.8935 workface were mainly induced by the seismic caused by roof failure. The coal pillar near the goaf is more easily to bump. The statistics results indicate that the coal bumps were mainly occurred in the gate road near the pillar, less than 50m ahead of mining face and located in the hard roof adjacent with coal seam. Moreover, the frequency, energy, b-value and frequency spectrogram of microseismic events were found to decrease before coal bumps. It was found that the frequencies of the microseismic events before coal bumps mainly concentrate upon 5~60Hz. The sudden decreasing of frequency and increasing of amplitude of microseismic events can be regarded as a precursor of coal bumps.

Aug 1, 2013

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement .Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By James K. Gowans

"Cominco Ltd&apos;s Polaris Mine, located on Little Cornwallis Island, Northwest Territories (latitude 75degrees 30&apos;) went into production in late 1981, becoming the world&apos;s most northerly base metal mine. The concentrator, powerhouse, shops, offices, dry and warehouse, were uniquely designed and constructed on a 100f t wide by 400 ft long by 65 ft high barge. This process barge was constructed in southern Canada at Trois Rivières, then towed 3,500 miles into the High Arctic Islands and beached on Little Cornwallis Island.The paper deals with the original design philosophy, flowsheet and the initial year&apos;s operation of the Polaris process barge.IntroductionTo bring a mining property into production in the Canadian High Arctic, a company must deal with the harsh environment, the short shipping season and the high cost of labour. In trying to minimize the effect of these fact or s, the concept of a barge-mounted process plant was investigated as an alternative to the conventionally built concentrator. Cominco&apos;s previous experience gamed at the Black Angel Min e on Greenland&apos;s west coast suggested that this would be a practical alternative.The normal shipping season at Little Cornwallis Island is approximately six weeks long, from mid-August to the end of September. All equipment and materials must be delivered during the ""shipping window"". The logistics problems are enormous; if the conventional approach had been used the major process equipment would have been delivered to Little Cornwallis Island at the same time as the completed barge actually was! Construction would also be starting at the start of the worst climatic conditions, the Arctic winter. Nine months&apos; production was gained by opting for the ""barge"" approach."

Jan 1, 1983

By Jo Render

Expectations of your management approach ??Life of mine applicability ??Tailor scale of activity to scale of project ??Assess impacts, risks, and opportunities ??Use global good practice, backed up by rigorous analysis ??Support with trained monitoring and evaluation team ??Information infrastructure to allow ongoing trend analysis and tracking of progress ??Public reporting using standardized indicators Yes, we are talking about a ?management system?

May 1, 2011

By Mel Owen, Bob Tipman

"A number of studies have identified the presence of heavy minerals in the Athabasca oil sands. A 1996 Mineral Development Agreement study into the recovery of Co-Products identified low operating costs, a simple flowsheet and access to market as key drivers in advancing interest in a viable project.Commercial bitumen extraction processes recover 50% of the titanium heavy minerals and 85% of the zircon into froth containing 1 % of the feed solids. Froth treatment tailings grade is 11.5% Ti02 and 3.6% Zr02.Processing this high grade feed in a combination of flotation, roasting, screening, gravity concentration and magnetic separation, results in concentrates of rutile, leucoxene, ilmenite, zircon and rare earths of marketable quality.A combination of high grade feed and a simple process lead to operating costs among the lowest in the industry. Low cost heavy minerals and low energy costs indicate an intriguing potential for low cost pigment production in Alberta. The production of heavy minerals from oil sands remains one of the largest untapped resources in the Province of Alberta1.0 IntroductionThis paper describes the results of an investigation into the recovery of heavy minerals from tailings produced by the major oil sands plants. The study was carried out under a Canada-Alberta Mineral Development Agreement (Alberta Chamber of Resources 1996). The MDA Co-Products Study examined the potential for the economic recovery of heavy minerals from oil sands tailings."

Jan 1, 1998

By W. Beres, Li. J.

The finite element method (FEM) has been applied to investigate the stress fields and deformation of a TiN/Ti-6A1-4V coating/substrate system subjected to nanoindentation. MSC Patran and MSC Marc were used to prepare the three-dimensional finite element models and to perform the simulations of the Vickers nanoindentation experiments. Pure silicon and TiN/Ti-6A1-4V coating/substrate system were analyzed. The properties of the materials were assumed to be homogeneous and isotropic with a linear hardening behavior. The reverse method was used to extract material properties, such as the yield stress and strain hardening coefficient, from the numerical results by comparing the simulated indentation load vs. penetration depth (P-h) curves with those obtained experimentally. Both non-linear elastic and non-linear elastic-plastic analyses were carried out for the coating/substrate system. The results are given for four different coating thicknesses.

Jan 1, 2004

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By Umbreen Agha, Stephan L. Chryssoulis, A. Margaritis

"The deportment of gold in samples of the biooxidation feed and product from the Harbour Lights mine in Western Australia was determined using optical microscopy and microbeam techniques such as Secondary Ion Mass Spectrometry (SIMS), Time-of-Flight Laser Ionization Mass Spectrometry (TOF-LIMS), and Electron Probe Microanalysis (EPMA). The main objective was to determine the mechanisms by which acidophilic bacteria (Thiobacillus ferrooxidans) liberate refractory gold which is locked in a sulphide minerals host as visible gold inclusions (> 0.1 µm) and as submicroscopic or 'invisible' gold.Using the integrated mineralogical approach approximately 99% and 100% of the assayed gold in the biooxidation feed and biooxidation product was accounted for. The results were compared to and verified by chemical assays.The gold deportment study indicates that during biooxidation, locked visible and 'invisible' gold is rendered cyanidable by the direct action of Thiobacillus ferrooxidans as well as indirect chemical leaching. Visible gold which is enclosed in sulphide minerals is liberated or partially exposed and is therefore rendered cyanidable as the host mineral is oxidized and dissolved. 'Invisible' gold either coalesces on the surface of the host sulphide mineral as the particle is dissolved or is released into the liquid phase and immediately adsorbs onto the surface of other ore particles with a net negative charge.The shakeflask suspension indicates that direct bacterial oxidation pits and channels correspond to zones of 'invisible' gold and arsenic (in pyrite) enrichment in the host sulphide mineral."

Jan 1, 1996

By T. Alan O'Hara

"Annual mining revenue can be computed by formulae relating metal prices, smelting schedules, concentrate grade and recovery to known ore grade and an assessment of core samples. Operating costs at different daily tonnages are related to orebody shape, mining method, milling process and general plant services. Capital costs are related to sizing of mining equipment, mine development, plant-site topography, climate and accessibility, plant services and personnel housing. IntroductionA crude guide to the average 1978 cost of mine projects is shown in Figure 1, but the costs of many mine projects have differed widely from the graphed average costs of $800,000 T0.6 for underground mine/mill projects and $400,000 T 0.6 for low-grade open-pit mine/mill projects.High mine project costs and high operating costs are characteristic of open-pit mines with high stripping ratios, underground mines with thin orebodies, mills with complex metallurgy, and projects located in isolated regions with severe climate, mountainous topography, and lacking access to existing roads, towns and electric power. When none of these adverse conditions prevailed, the mine project cost was typically much less than the graphed average cost. Virtually all the conditions likely to cause high capital and operating costs are known from knowledge of the local topography, climate or accessibility, or can be assessed by tests on core samples, as soon as the orebody has been outlined by drilling .A more accurate estimate of over-all project capital cost and operating cost can be made from a summation of items of cost after judging the effect of specific local conditions on each item of capital and operating cost. This paper offers guides in judging the effect of local conditions on the sizing and 1978 cost of specific items of capital cost and operating cost and operating cost of mine projects. When the specific items of capital cost and operating cost are totaled and measured against expected net revenue and taxes over the life of the mine using the net-present-value or discount-cash-flow methods, the result should show whether the mine project development is clearly feasible, doubtfully feasible or clearly uneconomic. If the development of the mine project is clearly feasible, or probably feasible, a detailed feasibility study by experienced consulting engineers should be commissioned before any financial commitments are made; but if project development appears to be uneconomic, the time and cost of a detailed feasibility study is not warranted."

Jan 1, 1980

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement.Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988