Search Documents

By R. Roufail

Mineral exploration is in a race to employ drilling technology that can perform the exploration and drilling investigation in a fast and inexpensive manner. After an extensive study of the available drilling technologies in the market, coiled tubing was chosen as a tool to be employed for mineral exploration due to its flexible mobility and ease of operation with a minimum number of personnel. Since coiled tubing technology is primarily used in the oil and gas industry, it was important to re-design the coiled tube rig to drill hard rocks in a fast and feasible manner. The main requirements were to drill the smallest feasible hole diameter and go as deep in the ground as possible, in the shortest reasonable time. The drilled rock particles, cuttings, are to be collected and analysed at the surface for their metal mineral contents. The process also needs to be repeated multiple times at different locations for mapping, without the need to change the tube on the rig due to failure or potential failure. The focus of the new designed coiled tube, for drilling and mineral exploration, is three fold. First is to increase the rate of penetration in drilling by designing a small high speed turbo motor. Second is to determine the controlling parameters of cuttings transport to effectively lift the cuttings to the surface for analysis and third is to minimize the overall weight of the rig for manoeuvring and prolong the life span of the coiled tube string. In this paper, a small downhole turbo motor, 5cm outer diameter, is designed to achieve a rotation speed of up to 10,000 rpm to fit on a small bit, coiled tube drilling assembly. The motor design utilised multiple finite volume and finite element analysis softwares for fluid flow study and fluid structural interaction analysis. The paper is also introducing the concept of a flow slurry loop that is designed to lift the cutting particles to the surface for mineralisation analysis. The controlling parameters of the cuttings transportation are the particle?s physical properties such as size, density, concentration and shape, as well as the rheological properties of the carrying fluid, drilled hole angle, as well as the fluid flow rate and flow dynamics within the annulus gap between the coiled tube and drilled hole. Such parameters are addressed via experimental work as well as numerical analysis. The paper is also presenting the selection and testing procedure of the material type for the coiled tube string. The tube needs to be light in weight for overall rig weight and its transportability. The tube is also required to drill several dozens of investigation holes before failing due to fatigue. A fatigue bending machine is designed to test the endurance limit of candidate materials for coiled tube strings and a performance index methodology is followed for material selection of the optimum material. The coiled tube rig is designed to be light in weight for transportation and relocation. It is also required to speed the drilling operation with the minimum footprint and reclaim the drilled rock particles for mineral composition analysis at the surface.

Aug 1, 2013

By M. E. Holuszko

A research program has been carried out at the Mining Department of the University of British Columbia to study the effect of wettability of coal on its handleability and bulk density. The effect of moisture content on the bulk density of coal was found to be more pronounced for hydrophilic coals than for hydrophopbic ones. Altering wettability of coal surface leads to different effects of moisture on bulk density. The samples were studied at different fine fractions content, and it was shown that there was no effect of increased content of fines on the bulk density for hydrophobic coals, while for hydrophilic coals this effect was very significant. It was shown that the moisture content at which the lowest bulk density was reached coincides with the critical moisture content for studied samples, as determined from handleability tests using Durham Cone method. This critical moisture is the moisture content at which a sudden deterioration of coal handleability occurs. Based on the bulk density and handleability tests, the flow theory of moist coal is proposed.

Jan 1, 2006

By Pierre O'Dowd

"The southern Abitibi Belt is the major source of gold in Quebec. Although the northern part of the belt is quickly being developed, the area under study will not be downgraded in the near future because it still contains more than 75% of the known reserves in the belt.Gold is found in a variety of geological environments which are part of a small number of distinct structural patterns. For the exploration geologist, outlining such patterns might be easier and more productive than defining, when it is possible, the exact genetic nature of the gold mineralization.Exploring in the right place has always been one of the main concerns of explorationists. This paper briefly describes the various favourable geological settings, and outlines areas, types of structure and lithologies of high potential for gold exploration in the southern Abitibi Belt.IntroductionThe southern part of the Abitibi Belt is a profilic mining area for precious and base metals (Lulin 1990). Although mineralizing processes and controls of polymetallic deposits are well known and understood (Lydon 1984), almost every gold occurrence is a unique case and numerous models have been proposed (Roberts 1987; Hodgson and McGeehan 1982; Hodgson 1990).This study does not define new genetic models for the formation of gold deposits, neither is it meant to elaborate on the existing ones. A genetic approach, is by definition, theoretical and, to some extent, universal. It helps geologists define types of targets and exploration tools but does not outline or quantify target areas. To tentatively summarize the complexity of a genetic approach, a brief discussion on the various genetic models in vogue in Abitibi and the problems related to their use in exploration can be found at the end of this paper."

Jan 1, 1991

By Roger Lafrance

"This paper discusses various aspects affected by the use of large-diameter boreholes in underground mines. Topics covered consist of noxious fumes, vibrations, post-blast effects, various types of explosives, the cordine system in production blasts, the slider primer system and wall-control methods. In general, the paper is an overview of this important fact of underground mining.IntroductionWith economical factors leading the way, many reasons motivated drilling equipment companies to develop equipment that can drill holes up to eight inches in diameter and even larger for underground applications. One of these other reasons is the fact that many orebodies were considered marginal, given the high costs of conventional mining methods utilizing small diameter boreholes. With these criteria in mind, accelerated programs were put in motion to develop equipment that would reduce both-development and production costs in underground mines. Change s in any basic program often affect other areas down the line. This is particularly true with the ad vent of large-diameter boreholes underground.C-I-L Inc. is certainly no stranger to this phenomena. Whether production headings increase in size and tonnage or whether production increases due to lower costs, one fact remains unchanged and that is the fact that all development and production holes are loaded and blasted whether they be of small or large diameter. Due to this fact, C-I-L Inc., as a leading explosives manufacturer, initiated a program to examine blasting methods in use in surface work with the intent of revising these method s for underground applications. Research facilities were also oriented toward developing appropriate products. This was a task that was accepted with anticipation, with the result that many new blasting systems and methods were brought forward, thanks to the collective efforts of both the consumers and manufacturers."

Jan 1, 1984

By O'Halloran. Gerard F.

"ECSTALL MINING has installed in their plants the most modern equipment in the mining industry. At the minesite, digital blocked frequency controls are used to monitor all crushers, conveyors, ventilation equipment and pumps from underground. Distant pumping stations are monitored and controlled by radio. Modern friction skip and cage hoisting systems have been installed with static power supply designed for automatic operation. Rotary-type compressors of recent design are in service in place of the conventional reciprocating-type units. At the concentrator, the 800- and 1500-hp synchronous motors driving the grinding mills have static field excitation and pneumatic clutches, still meeting modern-day concepts, having been• installed in 1966. The maintenance work load has increased annually for the past eight years. The modern plant, with all the present-day sophistication, must have a welltrained and well-organized force of skilled workers, and a maintenance system which will supply realistic facts and guidelines. This presentation will review the relative location of plants, utilities, maintenance and services, plant maintenance control and mechanical control. It is the hope that enough information will be presented to weigh the size of the job and how the resources are utilized for controlled maintenance."

Jan 1, 1974

By Michael Samis

Conventional project valuation techniques, such as discounted cash flow (DCF) method, are more frequently being criticised for the manner in which they consider the interacting effects of uncertainty and project structure (including management flexibility) on project value. Modern asset pricing (MAP; often called ?real options valuation? when applied to the analysis of flexibility) is a more general valuation framework that corrects many of the shortcomings of common valuation methods. Previous mining applications of MAP have tended to treat the ore deposit as a homogenous entity. While useful for demonstration purposes, this is inadequate for practical application in industry. This paper presents a MAP valuation example that allows for the heterogeneous nature of an ore deposit. It shows that deposit structure may increase the complexity of the mine planner?s decision so that results of a standard DCF analysis, or a simple MAP analysis that ignores the details of deposit structure, are misleading. In the example, a management is considering the development of an adjacent low-grade zone while mining operations in a high-grade zone are ongoing. If the low-grade zone is developed before high-grade reserves are exhausted, the proposed development will include both low-grade zone development and a capacity expansion to handle additional low-grade reserve production. If development of these reserves is delayed until the high-grade reserves are depleted, then the low-grade reserves can be developed without a capacity expansion. A typical DCF analysis would reduce the management?s decision problem to three alternatives: 1) continue mining only in the highgrade reserves, 2) immediately develop the low-grade reserves and expand capacity, and 3) delay low-grade zone development until the high-grade reserves are exhausted. The model presented here allows the management to reconsider the development and capacity expansion decision on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably. The model presented here extends the ability of mine planners to describe actual project structure while using the MAP valuation framework that is already noted for its capacity to combine project uncertainty and risk insights with a dynamic project description.

May 1, 2001

By Raj K. Rajamani, Nikhil Dhawan

"Agglomeration has become common pre-treatment step to improve heap leach percolation thereby recovery, the fundamental understanding of the agglomeration process for crushed ores is still lacking. Agglomeration is required for ores which either contain excessive amounts of clay or an excessive quantity of fines generated during mining and crushing. Numerous experiments have been carried out in laboratory scale batch drums using different ores. It has been found out that experimental agglomerate size distributions exhibit self-preserving spectra. The self-preserving/ similarity distribution of the agglomerates is found to be independent of operating conditions and is uniquely determined by the size enlargement mechanism. An empirical model based on the absolute difference between moisture applied and optimum moisture was developed. This model uses self-preserving spectra in the form of a Rosin-Rammler distribution function to predict size distribution at different operating conditions. The empirical model was considerably easier to work with plant scale agglomeration drums. Also, a test known as dip test is developed which improves fundamental understanding of the agglomerate formation and growth mechanisms. This test also provides the progeny size distribution of each agglomerate size. The progeny size distribution was analyzed with a model that partitions the particles into a host and guest category. The ensuing partition coefficient identifies the behaviour of a particle as a host for other particles or a guest layering on other particles. This concept helps in identifying the type of agglomerate that would result for a specific feed size distribution. INTRODUCTIONHeap leaching is one of the hydrometallurgical processes that have served as a green and economically viable process for the treatment of low grade complex ores of copper, uranium, nickel, silver and gold (Dhawan et al., 2013). Heap leaching appears to be a favorable candidate for the least energy consuming process for low grade ores. In heap leach operations nowadays a pretreatment step known as crushed ore agglomeration has been implemented (Dhawan et al., 2013). A bed of agglomerates improves the uniform percolation of solution through the heaps of ore. Therefore, it was possible to treat wastes and mill tailings via agglomeration and heap leaching. Agglomeration pretreatment is required for ores which either contain excessive amounts of clay or an excessive quantity of fines generated during mining and crushing (Bouffard, 2005; Dhawan et al., 2013).While agglomeration has become common practice pretreatment step in heap leach operations, the fundamental understanding of the crushed ore agglomeration process is still lacking. The author reviewed publications up to 2012 on the crushed ore agglomeration process and did not come up with modeling studies on the topic (Dhawan et al., 2013). Some of the possible reasons can be the stochastic nature of the process, experimental difficulties, and lack of instrumentation for fundamental studies."

Jan 1, 2016

By Alexander Smith

"The Silver Standard mine is 6 miles by road northwest of New Hazelton, B.C., a small town on the northern line of the Canadian National Railways some l 75 miles northeast of Prince Rupert. The deposits lie on the western slope of Glen Mountain (elevation 2,100 feet), with the main adit, mill, and campsite at 1,300 feet. The deposits were found in 1910, shortly after the area had been swept by forest fire and during a period of prospecting activity spurred by the construction of the railway. Crude ore only was shipped until 1918, when a 50-ton gravity mill was built which operated until 1922. Gross value of production of this period, at present metal prices, was about $1,000,000.In 1947 the present company was formed and a 50-ton flotation mill installed. Production from 1948 to 1955 has been in excess of $10,000,000, and net smelter returns about two-thirds of this amount. More than 60 per cent of the production and 80 per cent of the profit have come from one vein, No. 6. On the 1,300-foot level this vein had an ore section 375 feet long and 2.5 feet wide, averaging 0.18 ounces gold, 85 ounces silver, 10 per cent lead, and 16 per cent zinc.The mine workings follow a simple pattern. A series of parallel veins, striking northeast and dipping southeast, are numbered from 0 to 12, starting at the northwest. They lie within a zone trending south 70 degrees east, and the distance between Nos. 0 and 12 veins is about one mile. Recently several cross-veins, dipping northeast, have been found between Nos. 8 and 12. They are apparently of the same type as the others, though they may not have the same structural controls. They could be an important new source of ore.The mine has been developed principally by crosscut adits at the 1,500- and 1,300-foot levels and a 510-foot shaft with levels at I, 150, 1,000, ·and 850 feet. Drifts and crosscuts total 17,000 feet, chiefly on Nos. I, 4, 6, 7, and 8 veins. The drifts are stoped by shrinkage, top shrinkage rill, cut-and-fill with resuing, or open stope methods. The mill produces a lead-silver-gold-copper concentrate and a zinc concentrate, with indicated recovery of more than 96 per cent (4)."

Jan 1, 1949

By M. K. Jain, Z. T. Xu, M. Bruhis, V. Hegedekatte

"Strain rate and temperature dependent deformation conditions are present during elevated temperature forming of aluminum and other metallic materials. While many constitutive laws have been proposed to represent such deformation conditions, a closer investigation often reveals their limited applicability in terms of fit to the experimental data, and interpolation within and extrapolation outside of the range of experimental stress-strain curves. This is often because material-specific primary deformation mechanisms of temperature-dependent strain and strain rate hardening are poorly captured. In the present work, the Voce-Kocks constitutive model based on mechanics of dislocations storage and annihilation has been found to be suitable for many metallic materials. The model was modified to include the effect of temperature dependent shear modulus. The modified model is then employed to represent the experimental data obtained from uniaxial tensile tests on AA7075-O sheet at elevated temperatures and strain rates. Also, hot gas bulging tests were conducted to verify the applicability of this model. Further, finite element simulation of the hot gas bulge test was performed by incorporating the model as a user material subroutine. Good general agreement was observed between the experimental and FE model predicted results. Some sources of discrepancy in the prediction are also discussed.INTRODUCTION There has been much interest in light-weighting of automobiles from automotive related industries to reduce overall carbon footprint and increase energy efficiency of the vehicles. Aluminum alloys, and especially the medium-strength 5xxx and 6xxx series alloys, have been the primary focus in the last 3 decades to reach the above environmental goals (Huo, Hou, Zhang, & Zhang, 2016) whereas aerospace industry has traditionally focused on high strength 7xxx series aluminum (Al-Zn-Mg-Cu) alloys for structural components (Deng, Yin, & Huang, 2011). Recently, there has been much interest in high strength 7xxx series aluminum as a replacement for heavier steel automotive structural parts such as A-pillar, B-pillar, side impact beams etc. (Harrison & Luckey, 2014). This is both interesting and challenging since the above aluminum structural parts will need to not only meet impact safety standards but also possess sufficient formability for manufacturing such complex parts. Since the formability of high strength 7xxx series materials is quite poor at room temperature, much interest has focused on improving both formability and final part strength via high rate hot stamping, in-die quenching, and subsequent artificial ageing process steps (Kumar & Ross, 2016)."

Jan 1, 2018

By M. Al Mukhtar, D. Hoxha, X. Brunetaud, D. P. Do, C. Auvray, L. Michel

"Mechanical behavior of rock joints is often the key factor governing the response of complex structures constructed in fractured rock masses such as underground openings or of objects assembling various stones blocks such as historical building walls or damaged marble statues. This paper aims at developing a theoretical model to describe the behavior of fresh joints based on the description of their morphology. The main idea of the model is to establish a link between the effective contact surface of joints and the frictional coefficient. Beginning from a chosen level of joint surface description where a joint is considered as “smooth”, the model describes the added friction with respect to the increase of the contact surface of the joints and the distribution of stress in these contacts. The model developed initially for asperities with regular geometry is firstly compared with existing models and then applied on fresh artificial joints. For that, healthy artificial joints have been characterised using in one hand classical CNL shearing tests and in another hand the morphology of joints. The joints surfaces are digitized before testing using a high resolution laser scanner (Konica Minelota Vivid 910) allowing to obtain a precision up to 10µm. From these scanned surfaces the morphology of joints is characterised on the profiles running in the direction of shearing and a mean value of friction is calculated using the developed model. This calculated value is then compared with that obtained from CNL shearing test and a good approximation is notedINTRODUCTIONThe role of the mechanical behavior of rock joints on the overall response of fractured rock masses is well established in many fields of engineering activity going from the stability of underground constructions (Souley M, Hoxha D, Homand F 1999), rock slope stability (Einstein H.H. Veneziano D., Baecher GB., O’Reilly K.J, 1983, Jaeger 1971), various rehabilitation of masonry construction, damaged stone artworks restoration (Michel L., Do D.P, Coignard B, Hoxha, 2014) and so on. In the same time the characterisation of the behavior of joints and their modeling is nowadays a dynamic field of research or/and investigations and many alternative approaches have been proposed (Barton, N.R. and Choubey, V. 1977, Tatone, S.A. Bryan, Grasselli Giovanni 2010, William C E. 2007). While empirical relations of shear strength with various parameters of the joint morphology are the most used in practice because of their simplicity (Barton. and Choubey, 1977, Barton 1973, Bandis S., Lumsden A. C. and Barton N. R. 1983) many other models of joint strength are developed based on mechanistic considerations (Haberfield CM, Johnston IW. 1994), multiscale approaches (Yang Z.Y., Di C.C., Yen K.C. 2001, Fardin N., O. Stephansson, Lanru Jing 2001) or micromechanical ones (A. Serrano, C. Olalla, R.A. Galindo 2014) to mention just a few of research trends on rock joints modeling."

Jan 1, 2015

By I. Westermann, K. Marthinsen, M. S. Remøe

"Al-Mg-Si alloys often add small additions of e.g. Mn or Cr, to form dispersoids, which may act as nucleation sites for Mg2Si particles after homogenization. The purpose is to ensure a high density of uniformly distributed small ?’-particles, which can be dissolved during further processing prior to the final age hardening step. However, their density and spatial distribution are critically dependent on the homogenization procedure. It is therefore important to have a robust and reliable method for assessing their spatial distribution. In the present work an existing methodology for assessing spatial uniformity, the Global Shannon Entropy (GSE), has been implemented and evaluated for different dispersoid structures characterized by scanning electron microscopy. This metric is highly dependent on the parameters used, but by careful selection of adequate parameters, it can be effective in detecting non-uniformity. An important weakness with the GSE was identified, and a modification to improve on the ability to differentiate degrees of non-uniformity is suggested. To evaluate the proposed methodology, the effect of heating rate on dispersoid precipitation behaviour during homogenisation of four Al-Mg-Si alloys with different Mn/Cr-content has been investigated. The metric with the new term has demonstrated promising results, and improved the ability to differentiate degrees of spatial uniformity.INTRODUCTION Al-Mg-Si series alloys are the most common aluminium extrusion alloys and are attractive for applications in a range of sectors (e.g. construction, automotive and recently also in consumer electronics), due to their generally good combination of strength, ductility and corrosion resistance. However, their extrudability and end properties depend critically on the alloy chemistry as well as prior processing conditions. Coarse ß-AlFeSi or Mg2Si-particles typically have a detrimental effect on extrudability, while small dispersoid particles may affect recrystallization, grain growth and precipitation of Mg and Si. The strengthening potential in the final age hardening step depends strongly on the amount of Mg and Si in solid solution after extrusion. The manner in which these particles are spatially distributed will decide whether the final product will exhibit uniform properties, and the number density and sizes will determine the extent of the effect. As such, these are important characteristics."

Jan 1, 2018

By L. Szecowka, M. Poskart, Siwka M. . J.

Oxides of nitrogen, created during combustion, are the most hazardous components of atmospheric pollution. However, it is possible to limit the negative influence of hazardous components on the natural environment. An experimental appartatus was built to determine the influence of the following "primary methods" on the reduction in concentration of NOx: air staging, reburning and flue gas recirculation. The influence of the simultaneous usage of the primary methods on reduction in NOx emissions was also examined. A significant increase in the efficiency of NOx reduction was achieved in two cases.

Jan 1, 2004

By A. Himsley, E. Byleveld

"With reference to the chemical constraints underlying the ion exchange process for uranium recovery, a generalized view is presented on the actual and the achievable efficiency of the process. The area considered is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution.A comparison between actual plant results and the chemical requirements shows that:(a) Unless new and better ion exchange resins are developed, no dramatic change in equipment size and resin inventory is""anticipated. (b) Elution efficiency, especially for sulphuric acid, may be improved considerably. More concentrated eluates may beproduced at lower chemical consumption. A possibility of achieving additional purification solely by ion exchange is discussed.IntroductionThis paper presents a generalized view of the actual and the achievable efficiency of the ion exchange processes for urannium recovery. The study is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution. The ultimate efficiency attainable with ion exchange is dietacted by the chemical reactions underlying the process. The most sophisticated technology cannot change the diffusion rates in the ion exchange resin nor make the uranium loading exceed its equilibrium valueThe design of an ion exchange plant for uranium recovery involves a considerable number of parameters as a result of the wide variety of pregnant solutions produced from different orebodies. Therefore, a generalized approach of the ion exchange process inevitably neglects some parameters which maylead to significant variations in apparently identical situations.The uranium concentration in the pregnant solution, together with its pH, are the principal variables which determine resin loading and residence rime in the ion exchange system. On the elution side, the type of eluant and its concentration will determine the contact time required and the amount of eluant needed to strip the resin. The temperature, the properties of the ion exchange resin, the total dissolved solids in the feed solution and the competing ions are other variables that affect the chemical performance; these, however, may be considered as a correction of the principal parameters if one is interested only in general trends."

Jan 1, 1980

By R. R. Song, Q. Li, H. Xing, X. C. Wei

Geomechanical modelling of fault stability is an important part of CO2 capture and storage (CCS) research program to ensure its viability and long-term safety. Storage of CO2 in deep subsurface reservoirs requires estimates of sustainable fluid pressures that will not induce fracturing or fault reactivation which could cause fault slip. More importantly, fault slip gives rise to seismic waves, which inflict severe damage to the cap rock of the reservoirs and may result in leakage pathways for the buoyant plume and thus compromise the integrity of seal formations. In this study, we generated a numerical model tuned towards conditions usually encountered in the Shenhua CCS demonstration project in Ordos basin. In particular, with the purpose of evaluating the sensitivity of the parameters as well as their relationships with the moment magnitude of the seismicity, a variance-based sensitivity analysis was adopted for importance ranking of the uncertain input parameters of the given model. However, such flow models could involve one or several spatial inputs, for instance, fault dip, distance between fault and the injection well, friction angle of fault, permeability of fault, Young's Modulus of fault, injecting pore pressure and the stress field. Studying the sensitivity to each of these spatial inputs motivated the present work. The results led to the following conclusions: fault depth and fault dip significantly affect the behavior of the fault and the fault slip becomes violent with the fault depth increasing and fault dip decreasing. Furthermore, the results indicate that slip time increases with the fault dip decreasing and decreases with permeability of fault increasing. In addition, the calculation of seismic moment and moment magnitude of an earthquake demonstrates that it rises significantly with the decrease of fault dip and the increase of fault depth, and it decreases with the rising stress field. The results show that variations of the only controllable parameter injection pressure do not show great influence to the fault behavior compared with other geological factors, which imply site selection is extremely important for the CCS projects.

Jan 1, 2015

By Y. Duna

The reliability of mine ventilation systems is critical to normal and safe production in a mine and includes reliability of the following parts: ventilation system branch (or passage), ventilation structures, ventilation network, and the fan. Among these, the reliability of a ventilation branch may be considered the foundation of the whole ventilation system. The branch ventilation flow includes four parameters: air volume; toxic and hazardous gas concentrations; temperature, and dust concentration. The calculation model for the reliability of a branch was established based on the analysis of normal distribution of flows in any one branch. Then, the efficiency of the ventilation structures and fire risk compromising the reliability of branch was studied. The results obtained were as follows: if the air volume, toxic and hazardous gas concentrations, temperature and coal dust concentrations of the branch are within reasonable limits, set at any stable state and at the same time, then this branch is reliable.

Aug 1, 2013

By George Meadows

Consultation and Accommodation Introductions Consultation -Best Practices The Role of Negotiations The HVC Experience Summary / Conclusions The Challenge Meeting legal and policy obligations to consult while adhering to project priorities, timelines and budgets Defining who needs to be consulted, by whom, and ?how much?? Accommodation ?who is responsible and what is the appropriate scope? Social License -establishing positive working relationships with First Nations involved in project review / approvals / implementation in a manner that advances the interests of all parties

May 1, 2010

"A growing public awareness of work-related diseases such as pneumoconiosis and the impact of this awareness on legislative bodies and on the skilled labour market are reasons why the Canadian mining industry must consider dust control of top-drawer importance. Measurements and standards related to the hazard are necessary to control a dust situation and to avoid excessive risk. The author discusses some of the methods of measurement, standards proposed and terminology used in this developing technology. The purpose primarily is to give a better understanding of the basic advances achieved by those who have applied current knowledge with a measure of success."

Jan 1, 1972

By E. O. Lilge

THE USE of the Driessen cone as a heavy-media concentrator involves a mineral dressing process in which many variables inherent in the ore and in the process may have an effect on the efficiency of mineral separation and the operation of the cone. The magnitude of these effects and their possible interrelationships must be known before a full-scale plant can be designed and built. It appears that, among the most important variables, are the following: Ore Variables: The particle size of feed The difference in specific gravity between economic and non-economic minerals The intimacy of mineral association Cone Variables: Cone inlet area Ore to media ratio Cone ratio Size distribution in heavy media Specific gravity of media Viscosity of media Type of media

Jan 1, 1956

By P. D. Barrette

This paper deals with the flow of granular materials in bins. A hybrid Lagrangian-Eulerian numerical model is introduced. The model is based on Particle-In-Cell (PIC) advection, and continuum equations describing a Mohr-Coulomb criterion. Experiments were conducted to test and verify the performance of the numerical model. Tests were done using three types of particles. Measurements of material properties and flow rates were carried out. Video records were also obtained and used to examine flow patterns. The results indicate that the numerical simulations produce deformation patterns and flow rates which are in good agreement with the experimental observations.

May 1, 2007

By Ross L. Sherlock, David J. Scott, Gordon MacKay, Wayne Johnson

"Abstract - The demographics of Nunavut indicate a very young and poorly educated population spread over wide areas in small isolated communities. The current economic sectors will be unable to expand and meet the demands of this emerging workforce. Given the realities of Nunavut, the most promising direction in which the economy may expand is through mineral development. The Nunavut Land Claims Agreement (NLCA) has established the legislative framework for sustainable development in Nunavut through mineral development. The NLCA has transferred ownership for much of Nunavut’s potential mineral resources to beneficiaries of the lands claim. Royalties generated from mining operations on subsurface Inuit-owned lands, and to a lesser extent on Crown land, will flow back to beneficiaries of the lands claim through their administrative company, which may then be invested in the communities. Additional benefits of mineral resource development in Nunavut will be realized through impact and benefit agreements.To realize the benefits from mining operations, Nunavut has to be able to attract and support exploration and development companies through the release of high-quality geoscience data. However, due to Nunavut’s isolation and the expense of conducting geoscience fieldwork, the jurisdiction lags far behind the rest of Canada in terms of quality and quantity of government geoscience. About 70% of the territory is inadequately mapped to attract exploration companies or to make informed land-use decisions. The role of government-funded geoscience in Nunavut is to stimulate exploration and discovery through new framework mapping and focused thematic projects. The timely delivery of high-quality geoscience products will attract exploration companies to Nunavut and further their efforts to discover and develop mineral resources in order that the subsequent benefits of this activity may flow to the beneficiaries of the NLCA as well as all other residents of Nunavut."

Jan 1, 2003