Search Documents

By O. W. Borgeson, D. K. Honsberger, R. T. Bell

The Scully Mine, situated in the Labrador Trough near the Quebec-Labrador boundary, is one of the world's largest continuous ore deposits. This paper outlines the sequence of the mining operations from the planning stages to the delivery of the ore to the crusher at an average rate of 50,000 tons per day, 7 days per week. The principal equipment required to maintain this production rate includes four 12.\1.1-inch rotary drills, seven 8-cu.-yd electric shovels and a fleet of large haulage trucks. Particular attention is given to grade control, programmed by computer, drilling and blasting techniques and operational aspects inherent with open-pit mining in Canada's North.

Jan 1, 1969

By A. R. Hekmat

Hypereutectic Al-Si alloys are used in applications that require high resistance to wear and corrosion, hardness and low coefficient of thermal expansion, To maximize the properties of these alloys, semi-solid processing can be utilized to modify the solidification structure of the primary silicon crystals as well as to reduce microsegregation and porosity, The transformation and spheroidization of primary Si crystals by shearing in the semi-solid state are not fully understood as they precipitate in the presence of other alloy phases, The objective of the present work is the determination the rheological characteristics of A390 (Al-17%Si-4,5%Cu-0.5%Mg) alloy using a Couette type (Haake RV12) viscometer and examining the microstructural evolution during continuous cooling and isothermal shear rate experiments, The effect of shear rate, solid fraction (temperature) and morphological evolution of the silicon crystals are investigated.

Jan 1, 2005

By S. B. Kang

Magnesium has poor ductility at temperatures lower than 225°C and, as a result, Mg alloy sheets are produced via fairly complex thermomechanical processes consisting of numerous sequential steps of hot (warm) rolling with low reduction and intermediate recrystallization annealing operations. In context of the present study, a simple technology for the fabrication of magnesium sheets by hot (warm) rolling was applied to various magnesium alloys. The misch metal addition in those AZ alloys was done to evaluate the deformation behavior. Tensile tests were carried out for those AZ alloys after applying different heat treatments. The precipitation of ß phase (Mg17Al12 phase) induced different microstructures with various cooling method from solution treatment temperature, and also with various annealing treatment temperatures.

Jan 1, 2006

By D. Tao

The adverse effects of clay particles on coal and mineral processing processes such as gravity separation, flotation, filtration, and thickening are well known in the mining industry. In particular, the presence of ultra-fine clay particles deteriorates froth flotation performance, which has been attributed largely to slime coatings that inhibit bubble attachment and to adsorption of the frother and/or collector by the clay particles. The present study was conducted to evaluate the performance of clay binding agents developed by Georgia-Pacific Resins, Inc. in enhancing coal and mineral flotation performance. Mechanical and column flotation tests were carried out using coal and potash samples. Process parameters investigated include slurry solids percentage, impeller rotation speed, binder dosage, collector dosage, etc. Flotation results show that use of GP reagents significantly enhanced flotation efficiency under different conditions. The required binder dosage and conditioning time was about 1 lb/t and 0.5-1 min, respectively. More significant improvements in process performance were observed at higher solids percentage and higher impeller rotation speed.

Jan 1, 2006

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company's mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

By Gordon A. Gross

During the last half century major steel industries of the world have become dependent on iron and manganese resources derived from siliceous ironformation sediments. More than two billion years ago vast amounts of iron and manganese were deposited in ironformation sediments on all continents and until recent years their genesis was considered to be a uniquely Precambrian phenomenon. Research work has demonstrated that the origin of the banded ironformations was related to major tectonic features and associated volcanogenic processes that were active throughout geological history. Similar sedimentary-tectonic environments are being explored on the seafloor where metalliferous sediments are forming today. Ironformations are now considered to be a major part of the stratafer group of stratiform metalliferous deposits. They developed in sedimentary basins in areas where deep tectonic fracturing intersected high thermal gradients in the earth?s crust and gave rise to profuse volcanism and the hydrothermal effusive discharge of metals in the vicinity of the volcanic centres. Concepts for the genesis and metamorphism of stratafer deposits as revised in the last half century have had a profound impact in the development of iron ore resources and have had a dramatic impact in the use of metallogenetic concepts for guiding exploration for other mineral resources. They are based on the tectonic history and stratigraphy in the sedimentary basins, the role of hydrothermal volcanogenic processes , as well as environmental and sedimentation factors which influence the deposition of silica, iron , and other metals that were emphasized in the past. Topics of special interest in the genesis of ironformation and stratafer deposits and for guiding mineral exploration are: biomediation in their sedimentation and genesis, the significance of metamorphism in the processing and beneficiation of iron ore and in the genesis of iron ore by natural enrichment processes, syngenetic concentrations of Mn, Ti, Cu. Zn, Pb, Ni, Co, REE, F, Ba, B, As, Hg, W and Au in ironformations and stratafer lithofacies, and the mobilization of gold and other elements by alkaline solutions during diagenesis of ironformation and other stratafer metalliferous sediments.

May 1, 2003

By J. Kempken, R. Hagmann, C. -P. Reip, W. Hennig

The CSP technology symbolizes a highly productive process for the cost-effective production of steel grades with a range of sophisticated properties comprising both the inner quality of hot strip, its surface formation as well as the relating technological characteristics. Thanks to extensive development work undertaken during the last 15 years, the range of steel grades that can be produced was continuously expanded and the process technology optimized. The present paper describes the ongoing development work concerning the production of higher-strength, microalloyed pipe steels. The resulting hot strip, due to the associated thickness and the potential pipe diameters, is particularly suited for being processed to HFI-welded pipes. Based both on ferrite-pearlite as well as very fine-grained, ferrite-bainite hot-strip microstructures, strength levels of up to grade API X80 can be realized. It can be demonstrated that hot strip produced in a CSP plant has very good toughness values at temperatures down to -60°C and can even make application with required sour-gas resistance possible.

Jan 1, 2005

By Soumitry J. Ray

Poor visibility of powered industrial vehicles, such as forklifts, used in industry is often the cause of accidents that include pedestrians. Current standards allow up to 20 % non-visible regions for forklifts where measurement of these regions is performed by using lamps. A collaboration of research organizations, including National Institute of Standards and Technology, Georgia Institute of Technology (NIST), and Direct Dimensions, has been evaluating advanced methods for measuring a forklift operator?s visibility. These methods can potentially improve visibility standards. They can also help forklift and sensor manufacturers to determine (1) how visibility-assist sensors and algorithms can be designed and (2) where sensors can be mounted on forklifts. This paper includes explanation of visibility measurement experiments performed and results, associated language suggested to standards organizations, and a prototype design for measuring the visibility of forklifts automatically.

Aug 1, 2013

By S. E. Jackson, L. J. Cabri

Quantitative determination of gold at sub-ppm concentrations in sulphide minerals is an important component of deportment studies for sulphide-gold deposits. Laser Ablation Inductively Coupled Mass Spectrometry (LA-ICP-MS) analysis is preferred for this application because it rapidly and cost-effectively provides spatially resolved (<20 pm), low ppb concentration data for gold and other elements in mineral grains. Recent advances in LA-ICP-MS analysis include the development and application of elemental mapping. Raw signals from multiple line scans or lines-of-spots are deconvoluted and calibrated to generate elemental maps which provide detailed information on spatial variations of gold and other elements within and between grains.

Jan 1, 2011

By R. T. Saxon

Prior to November 1975 there were several failures of front -wheel spindles on large haulage truck s in B.C., attributed to fatigue cracks. Since that time, a non-destructive test program has succeeded in detecting the cracks before catastrophic failure, However, the author regards the failures as just one example of a. general unreliability in large high-strength steel castings and urges the industry to look to forgings for sensitive components of heavy equipment.

Jan 1, 1977

By W. G. Jewitt

THE Box mine, situated in Saskatchewan on the north shore of lake Athabasca, is unique in two respects. It is the first and, so far, the only gold mine in Saskatchewan, and it is the only gold mine in Canada to employ a large-scale forced caving system as the main mining method. Discovered in 1934 by Tom Box, an Edmonton prospector, its subsequent history, while breaking no records for speed, has been one of steady and more or less normal development. Camp and plant are situated close to the shore of Beaverlodge bay, sorne 50 miles east of the Saskatchewan-Alberta boundary and 35 miles south of the north boundary of the Province. The railhead at Waterways, Alberta, is about 220 miles to the southwest. Prince Albert lies some 450 miles to the south. The surrounding country presents a rather rugged variation of the usual Precambrian topography, with hills rising five to six hundred feet above lake Athabasca. The numerous lakes and islands, together with the wide expanse of lake Athabasca, compose an attractive scene, at least in the not over-long &apos;open water&apos; season. The winters are long but not extremely cold, judged by prairie standards. The small lakes break-up around May 20th and the &apos;freeze-up&apos; stops navigation early in October. Though apparently remote, the Box mine is fortunate in having reason-ably cheap transportation from Edmonton. The 300-mile railway from Edmonton to Waterways is the most expensive section, the rate for 1st class freight being $1.70 per hundred pounds and for 5th class freight $0.77 per hundred. Freight from Waterways to the mine, approximately 140 miles down the Athabasca river and 90 miles along lake Athabasca, is delivered by barges and tugs for 50 cents per hundred pounds. All freight is delivered during the &apos;open water&apos; shipping season, which lasts from about .Tune 7th to October 7th. In normal years, barges are loaded to 3 to 3 1/2feet draught up to September 1st. After that date, and earlier in dry years, shallow water at Waterways reduces the barge loads. Barges of 100 to 200 tons capacity handle all mining freight, including pieces up to 15 tons in weight, without undue difficulty.

Jan 1, 1940

By T. A. Utigard

To improve recoveries of Ni, Cu and Co in the Inco flash furnace, a new operating concept was investigated. By adding sufficient coke to form a supernatant coke layer, a reducing barrier would form allowing for improved reduction of descending oxidized sulfide mineral particles formed in the flame. The objective of this investigation was to study the kinetic mechanism and efficiency of the coke layer to produce a sulfur deficient matte. The mechanism and rate of carbon reduction of each of the phases formed in the flash flame, i.e. sulfides and oxysulfides were investigated by means of X-ray visualization tests. Graphite-slag reduction was also conducted for comparison purposes. In the case of slag, poor wettability and the formation of a gas film on the surface of the carbon reductant are often blamed for limiting the reaction surface area that ultimately results in poor reaction kinetics. The X-ray visualization tests confirmed that matte and oxysulfide wet coke better than slag and that the rates of reduction of matte and oxysulfide are faster than that of slag.

Jan 1, 2005

By S. Kashani-Nejad

The formation of oxides during the dehydration of MgC12,6H20, Bischofite, was studied by heating the bischofite over a range of time and temperatures in ambient atmosphere. Using a methanol-leaching technique developed by authors, the oxides that formed were isolated, identified and assayed. Three distinct regions of oxide stability were identified. The oxide produced at dehydration temperatures less than 300 °C was Mg2(OH)3C1,2H2O; at 300 °C, mixtures of MgOHC1 and Mg2(OH)3C1.2H2O were formed and at 400 °C, MgOHC1 was the only oxide produced. The presence of MgO observed in the products of the dehydration of bischofite at temperatures above 400 °C was due to the thermal decomposition of the MgOHC1 that was formed while the sample was heating to over 400 °C.

Jan 1, 2006

By P. K. Kaiser, C. D. Martin, F. Amann

"This article focuses on the uniaxial compressive strength (UCS) of homogeneous and heterogeneous rocks. Critical factors impacting the UCS of rocks are reviewed and then separate assessments of UCS data from homogeneous and heterogeneous rocks are presented. The variability (coefficient of variation) of UCS test results for homogeneous rocks is found to be generally <25% while for heterogeneous rocks the variability is >35%. Failure mode variation is found to be the cause of the variability of UCS test results in heterogeneous rocks. Empirical engineering design methods that use UCS as an input parameter are discussed and suggestions are provided for selecting appropriate UCS values.INTRODUCTIONThe UCS is one of the most commonly used rock engineering parameters whether for rock mass classification or for strength determination. The mean UCS and its variability are often assumed to represent a reliable rock material property. For the reasons discussed in this article, UCS is rarely representative of the intact rock UCS. The UCS test simply records the collapse load during uniaxial loading of a cylindrical specimen. As suggested by many, the UCS is an index rather than a unique engineering parameter. The UCS is thus a proxy for rock strength which depends on the loading rate (e.g., Bieniawski 1967), specimen geometry (e.g., Hudson et al., 1971), specimen size (e.g., Bieniawski 1968), and many other factors. Furthermore, the UCS is not the same as the Hoek-Brown strength criterion parameter sci.There are differences in opinion on what is commonly considered to be ‘intact rock’. When sampling ‘intact’ pieces of core from drillholes crossing blocks of rock bound by block forming discontinuities, samples will be ‘intact’ but some samples will be veined, others will be damaged, and others will be neither. According to Hoek (1983), intact rock pieces are “the unfractured blocks occurring between structural discontinuities in a typical rock mass” and the sci parameter for intact rock is determined using the fitting procedure proposed by Hoek and Brown (1997) based on the data requirements outlined by Hoek (1983). Studies (e.g., Bewick and Kaiser 2014; Kaiser and Kim 2014) have shown that independently determined UCS and sci values for the same rock type are not equivalent. Thus, UCS data cannot be used as a replacement for sci."

Jan 1, 2015

By S. F. Guo, B. W. Zheng, X. L. Huang, S. W. Qi

"The study of mechanical characteristics of rock discontinuities under different shear deformation velocities is an important premise of rock slope dynamic response analysis. According to disposing and calculating the experimental results of previous research about peak shear strength of rock discontinuities under different shear deformation velocity of constant normal loading, the law of influence of shear velocity on the total friction angle is studied. Based on the research results, it can be found that the total friction angle of rock joint specimens varies in the form of negative logarithm with the variation of shear deformation velocity. It’s also indicated that the total friction angle of rock joints decreases with the increase of shear deformation velocity for rock joints of relative strong homogeneity and isotropy. However, the total friction angle of rock joints increases with the increase of shear deformation velocity for rock joints of relative strong heterogeneity and anisotropy and the latter amplitude of increase is less than the former amplitude of decrease. The physical property and microscopic geometry of rock joints play an important effect on the increase or decrease tendency and amplitude variation of total friction angle with the increase of shear deformation velocity.INTRODUCTIONThe rock slope dynamic response is largely restricted by rock discontinuities. Hence the study of dynamic characteristics of rock discontinuities, especially the dynamic shear characteristics is an important premise of rock slope dynamic response analysis (Qi et al., 2007). Seismic load is both dynamic load and cyclic load (Liu et al., 2011). Under the dynamic and cyclic shearing actions of seismic load, the rock slope which is stable under the condition of static load may slide along the rock discontinuities whose shear strength reduce and then the earthquake landslides occur. The strength degradation and deformation mechanism of rock discontinuities under the dynamic and cyclic shearing actions is one of the key problems to be solved in the work of earthquake prevention and control of engineering slope. Based on the above understanding, predecessors conduct some researches which focus on the shear behavior mechanical characteristics of rock joints under cyclic shearing actions (Plesha, 1987; Hutson & Dowding, 1990; Jing et al., 1992, 1993; Huang et al., 1993; Qiu et al., 1993; Homand et al., 2001; Lee et al., 2001; Jafari et al., 2003; Liu et al., 2011, 2013). However, there are a few researches about the mechanical characteristics of rock joints under different shear deformation velocities because of the restriction of shear apparatus. Crawford and Curran (1981) conducted a series of one-way cyclic direct shear tests on four kinds of natural rock joints under different shear deformation velocities varying from 0 to 200 mm/s. The tests showed that at low normal stresses the peak shear strength of soft rock joints exhibited an increase up to a certain velocity, after which it remained essentially constant. For rock joints of intermediate hardness, the peak shear strength was essentially independent of shear deformation velocity; whereas for hard rock joints, the peak shear strength of which showed a significant variation with the shear deformation velocity. Jafari et al. (2003) carried out a series of conventional triaxial tests on artificial rock joints of regular saw-tooth shape with axial loading rate from 0.05 mm/s to 0.4 mm/s."

Jan 1, 2015

By The Hollinger Mill Staff

ALTHOUGH cylindrical grinding mills have long been used, there is wide divergence of opinion as to what constitute best operating conditions. Questions such as mill diameter, diameter-length ratio, revolutions per minute, type and size of grinding media, volume of charge, circulating load, pulp level, pulp consistency, liner design, and size of feed, have all been given serious consideration by competent scientific investigators as well as by operators. While many laboratory and plant tests have been made that would seem to justify certain definite conclusions, there is a dearth of definite data giving actual results obtained when a grinding mill working between fixed limits is operated at its maximum capacity under varying conditions as to ball load, circulating load, speed, etc. In tests conducted recently at the Hollinger, extending over a period of thirteen months, to determine the best operating conditions for a ball-mill 6 ft. 6 in. diameter inside the liners, some very interesting facts have been ascertained. This paper is presented in the desire to make public the results of these tests and not with the idea that the last word has been spoken in regard to grinding. We feel, however, that these facts justify certain definite conclusions and hope that, by the fullest and frankest criticism and discussion, the essentials necessary for the correct design and operation of grinding mills will become better known.

Jan 1, 1937

By H. J. McQueen

The irregular history of Mg wrought products is briefly described. The temperature and strain rate dependence of microstructural evolution, flow stress and ductility of Mg alloys in hot working, are described. The flow curves rose rapidly to a peak stress which was lower as temperature T rose and strain rate e declined and above 300°C the curves extended into plateaus until failure. Clearly grains not oriented for slip undergo mechanical twinning in the initial stages (a 0.15) at all temperatures. Basal slip proceeds in suitable grains and in the twins. The stress concentrations at grain and twin boundaries lead to slip on non-basal systems and to the formation of subgrains with greater dynamic recovery (DRV) at higher T or lower e. With increasing strain, misorientation builds up resulting in dynamic recrystallization (DRX) first at twin intersections and later at grain boundaries which have become quite serrated. Even after extensive straining at high temperatures, the new grains are found mainly along the boundaries of the original grains, leaving their centers with only basal slip except when nucleation at twins leads to completion of DRX throughout a grain. Despite similar shear modulus and melting point to Al, hot mechanical forming behavior of Mg alloys differ due to differences in crystal slip systems, twinning, and second phases. Moreover, the influences on forming of alloy additions (solutes, segregation in casting, dispersoids, precipitation) and impurities are not as well catalogued as for Al. Despite the benefits from dynamic recrystallization, varied grain orientation effects, heterogeneous substructures and the resulting stress concentrations result in considerably lower ductility for Mg alloys at the same stress level as for Al materials. Application of these theories to extrusion, rolling and forging and the effects on product properties are surveyed.

Jan 1, 2006

By E. L. Warburton

Before entering into a discussion of wet washing, it will be advisable to consider the various phases and conditions sur- rounding the problem of cleaning coal from the Corbin mines. Corbin is located in the south-east part of British Columbia in the Crowsnest Pass district, about 35 miles north of the International boundary and about three miles west of the Flat-head Range of the Rocky Mountains. It is reached by a rail-way, about thirteen miles long, from McGillivray, B.C., a point on the Crowsnest branch of the Canadian Pacific rail-way, owned and operated by the Eastern British Columbia Railway Company, a subsidiary company of Corbin Coals, Limited. The coal is assumed to occur here, as principally elsewhere in the Rockies, in the Kootenai series of the Lower Cretaceous, but owing to the disturbed condition of the surrounding country and, therefore, the magnitude of the geological study involved, this has never been definitely worked out. The coal is of the usual Crowsnest high-grade steam-coal, containing from 9 to 12 per cent. of ash, but appears to have 4 to 5 per cent. less volatile combustible matter than other coals being mined in this district, a representative analysis being about as follows:

Jan 1, 1924

By A. Allaire, J. Torrealba-Vargas, R. Welyhorsky

Early testwork was carried out to select the plant process design criteria and flowsheet selection. Additional testwork was carried out during the feasibility study to support the optimization of the plant design criteria. The test results showed that the recovery of gold was not very sensitive to grind size in the range of 75 to 105 microns. An additional result was that the presence of lead nitrate did not improve the kinetics of gold leaching. This conclusion was supported by the low content of sulphides in the ore. It was also found that the presence of lead nitrate increased copper dissolution, producing the potential for an increase of copper reporting to electrowinning, which is detrimental to the overall gold recovery process. The use of oxygen in leaching was investigated to increase leach kinetics. The results of leaching tests to compare using oxygen instead of air indicated that, due to the improved leach time, it was possible to reduce the number of leaching tanks from twenty four (24) to twenty (20).

Jan 1, 2011

By H. Abdollahi

Cold rolling is one of the most important techniques in metal forming since the cold rolling products are almost finished product, The product quality of this process is widely influenced by friction in the roll gap; therefore, controlling the friction and other parameters affecting the cold rolling is very important in order to have a product with high quality, Among the cold rolling parameters, the pressure distribution or friction hill within the roll gap is known as the most significant one, In this study, a new software (Matroll), is introduced which can determine the coefficient of friction (COF) and plot the friction hills for an industrial mill, Besides, based on rolling equations, it offers about 25 rolling parameters as outputs. To verify the software operation, the real industrial rolling data was used as inputs, The results (outputs) are in good agreements with the findings of other researchers, The COF values are very reasonable, The friction hill shows that COF is not constant over the whole arc of contact.

Jan 1, 2005