Search Documents

By B. Calver, D. J. M. Farnsworth

"As open-pit operations expanded at Pine Point, hydraulic aquifer evaluation was undertaken to establish the criteria necessary for the design of a feasible dewatering system.The extreme climate of this northern location dictated that the ore zone under extraction be rendered as dry as possible to minimize freezing effects. The design and implementation of such a system necessitated detailed hydraulic evaluation, and the problems that occurred are typical of those inherent in open-pit mining operations in northern areas.The paper describes the problem solution as approached from a mine engineering point of view, with particular reference to the practical aspects of operation and installation. The hydrological analysis used is simple and readily applicable to most open-pit dewatering problems."

Jan 1, 1969

By Finley A. Campbell

THE Quemont and Horne mines are located at Noranda in north-western Quebec. As shown in Figure 1, the Noranda area lies between the Cadillac-Bouzan fault zone on the south and the Porcupine-Destor fault zone to the north. Both of these major structural lineaments appear to be geometrically, and possibly genetically, related to the Grenville Front. The regional geology has been discussed by Wilson (12), Cooke et al. ( 2), and others. The geology in the Noranda vicinity, as compiled by Dugas and Gilbert ( 3), is shown in Figure 2. The Cadillac-Bouzan fault zone separates the dominantly Temiskaming-type sediments in the south from the Keewatin-type canic rocks to the north. These volcanics, which vary in composition from rhyolite to andesite, form a broad anticlinorium with a general eastward plunge. A succession of dioritic stocks, sills and dikes have been mapped in the area. The principal granitic rock masses include the Powell, Flavrian and Dufault stocks.

Jan 1, 1962

By Daniel J. Corkery

Mines in Canada and the United States are subject to regulations limiting ammonia, nitrate and nitrite levels in mine effluents released into the environment. The primary source of these nitrogen compounds is typically explosive used in blasting operations, as ammonium nitrate (AN) remains a significant component of most explosives used in the mining industry. The amount of AN entering a local water drainage system is related to site conditions, explosives used, explosive handling and blast efficiency. Mining operators acknowledge AN loss to mine water from blasting operations. However, the mechanisms by which ammonia, nitrite and nitrate are entering the water drainage system, or the relative contribution of specific mechanisms, may not necessarily be assessed or monitored adequately. Characterization of these mechanisms, through systematic investigations, allows a mining operation to focus its efforts on reducing AN loss. This paper outlines a strategy for investigating the mechanisms through which AN enters the mine water drainage system and methods to mitigate this loss. This strategy includes collection and analysis of data to identify and quantify the AN loss mechanisms, design and implementation of tests to mitigate this loss, and assessment of the results. Such investigations are not intended to be a separate one-time project, but part of a long-term process of continual feedback and optimization that is related to the collection and reporting of AN levels for regulatory purposes. The implementation of the strategy must be tailored to each mine?s requirements and existing conditions.

Oct 1, 2010

By P. Harvey

"Following initial discovery in 1991, BHP Billiton Diamonds Inc. opened Canada’s first diamond mine, the EKATI Diamond Mine (EKATI) in the Northwest Territories on October 14, 1998. Four short years later, on November 29, 2002, saw the opening of North America’s first underground diamond mine, the Koala North mine. Nestled between the original Panda open pit and the new Koala pit, which is in the early stages of production, Koala North represents the only underground kimberlite mining venture in Arctic conditions outside the new underground mines being developed by ALROSA in the Yakutsk region of eastern Russia. Extensive underground kimberlite mining has been practiced in the Republic of South Africa for much of the 20th century and continues today.Underground mining represents a key component of the long-term business plan for EKATI. As various open pits reach their economic limit, continued recovery of high-value ore at depth is dependent upon the ability to productively mine the kimberlite pipes by underground methods. As a function of its location, size, and value, the Koala North pipe is ideally positioned to host the first underground mine at EKATI. Koala North is designed and approved as a learning mine, from which to gain valuable experience in preparation for the potential mining of other larger, higher value pipes by underground methods in the development, the Koala North mine is well into its production ramp-up phase and currently producing at around 1,200 t/day from the first two production levels."

Jan 1, 2005

By J. E. Hawley

This paper constitutes a report from the Committee on Geological Research to the Geology Division of the Institute. Two years have elapsed since a formal report was made containing several resolutions aimed at assisting geological research, a review of research equipment available, a summary of research projects suggested for consideration, and a list of research then in progress (see July, 1947, Bulletin, pp. 351-370). At this time we may note what action has been taken on the various resotions and suggestions of the Committee, indicate the more important accomplishments of independent investigators, and present a summary of the rather imposing volume and variety of research currently being carried on throughout the country. I.-Committee Resolutions and Suggestions 1.-A National Advisory Committee on Research in the Geological Sciences The original resolution adopted on the setting up of this Committee was approved with despatch by Council and was forwarded to the Minister of Mines and Resources. Due to a reorganization in the Department and possibly other reasons, no action on this important matter has yet been taken, but we are assured that some time this year such a Committee will be established by the Department of Mines and Resources. Unquestionably, it will give a fresh impetus to research in the geological sciences. When the noteworthy progress made by the research committees on Geophysics and on Soil and Snow Mechanics, established by the National Research Council, is considered, it is indeed regrettable that the Department of Mines and Resources has not acted more decisively in this matter.

Jan 1, 1949

By B. R. Johnston, K. D. Streeter

"ABSTRACTCoal Mountain Operations is the newest of Fording Coal’s operations although it is the oldest in terms of its historical production. In October, 1994, Fording purchased the former Corbin Creek/Byron Creek Mine. The mine is located in southeastern British Columbia, approximately 150 air kilometers from Calgary, Alberta. It was first developed in 1905 and has gone through a variety of owners in its 90-year history.This paper will deal with the remobilization strategy and the mining plans for the operation which are being implemented to make this operation competitive in the world export coal market. IntroductionIn October 1994, following a due diligence process, Fording Coal Limited purchased Coal Mountain Operations from Corbin Creek Resources, an employee group which had previously owned the mine. The purchase awarded Fording Coal Limited with 100% of the assets, and control of all the coal leases at Coal Mountain.The mine is located in southeastern British Columbia, southeast of Sparwood at the hamlet of Corbin, (Fig. 1).Rehiring of laid-off employees started in November 1994, with mining activities also recommencing in November. The coal preparation plant was restarted in December with one shift, went to two shifts in January 1995, and had four-shift, full-time operation in April 1996."

Jan 1, 1997

By Robert F. Shurtz

This paper discusses and compares methods of statistical analysis of the information relating to the evaluation of an asbestos deposit. From a study of 10-ft. lengths of drill core, the separate effects of visual evaluation errors were determined, as well as the deviations between evaluators and the deviations produced by a slight displacement in the center lines of the check drill holes. The importance of careful statistical analysis of such information is stressed.

Jan 1, 1966

By G. M. Ritcey, V. M. McNamara

"In the processing of gold ores by the cyanidation route, effluents which are discharged to the tailings areas can contain up to several hundred parts per million of cyanide in complex combination with similar quantities of heavy metals. Complicating this obvious problem of waste control are concentrations of thiosalts and thiocyanates which are roughly equivalent to the amounts of cyanide species. Although most gold mills are located in thinly populated areas, such contaminants can represent a potential environmental problem due to the various limitations exhibited by on-property ponding.The former Extraction Metallurgy Division of CANMET recognized the problem and, in early 1974, invited representatives of the gold mills to Ottawa to discuss the situation. At that meeting members of the Division presented a ""state of the art"" literature survey of cyanide abatement technology for waste solutions, together with preliminary cost estimate data(1). Shortly thereafter, Environment Canada, together with Environment Ontario, decided upon a guideline of 0.1 ppm (0.1 mg/l) total cyanide content as tolerable for an effluent stream which is discharged, in any manner, to the watershed."

Jan 1, 1978

By W. B. Timm

Introduction In preparing this paper on Recent Developments in Gold Milling Practice, the idea occurred to me that possibly the best way to deal with the subject would be to take you in thought on a visit to the principal gold mining camps of the Dominion, starting at the east and finishing up in the west, and noting, as we go, the outstanding improvements that have been made in the last few years in the practice of gold milling. Before beginning this tour, I desire to emphasize the debt this country, and particularly our mining industry, owes to that body of trained and experienced men, little heard of, but who, working quietly on their problems, are responsible for these improvements. The metallurgists, to whom I refer, have solved many difficult problems for the mining industry, in connection with the treatment of our complex ores; for instance, the silver-cobalt ores of the Cobalt district, the gold ores of the Porcupine district, the gold-telluride ores of the Kirkland Lake? district, the copper-gold ores of Noranda, the arsenical-gold ores of the Beattie mine, the copper-zinc ores of Flin Flon, and the lead-zinc ores of Kimberley. In doing so, they have maintained the high technical standards of the profession, and the practices thus evolved are noteworthy for their high degree of efficiency. When the price of gold increased from $20.67 to $35.00 an ounce, what had formerly been thought to be a low tailing became almost an ore, so that the metallurgists are now busily engaged upon the problem of putting this railing back in its proper place of being a tailing once more, or from its value, at the present price, of anywhere from 50 cents to a dollar or so per ton, to a few cents per ton. Owing to the changing prices of the metals in the world's markets, still greater improvements in metallurgical practices are imperative. An important contributory factor towards improvement in ore dressing is the aid furnished by the microscope in the examination of ores and mill products. By making possible the determination of the mineral constituents of the ore, their association, and grain size, it gives the investigator a knowledge of his problem, before he does any actual test work. In the Mines Branch laboratories at Ottawa, its use has enabled us to predict how an ore should respond to various methods of treatment.

Jan 1, 1935

By A. McLean, X. Men

"With high quality sulphide ores diminishing, nickel production from low-grade oxide ores becomes increasingly important and a major concern is the high sulphur level in the resultant ferro-alloy. So, desulphurization of the ferronickel becomes an important consideration. Red mud is a waste product of alumina industry and causes adverse effects on environment. In the present study, experiments were conducted to determine feasibility of using red mud as a major ingredient of refining fluxes for ferronickel desulphurization. In view of their influence on slag-metal separation, contact angle measurements between ferronickel alloy and molten slag made from red mud were also determined. INTRODUCTIONNickel is a very important metal that finds a variety of applications including consumer products, building, automotive and electronics. There are two kinds of ores containing nickel, namely oxide and sulphide ores. Anthony and Flett [1] reported that about 55% of the world’s nickel production originates from sulphide ores while the balance of new nickel is derived from oxide ores. However, oxide ores count for about 70% of the worldwide reserves. Apparently, oxide ores will play a significant role in the production of nickel in the future. Most of nickel produced using oxide ores is from pyrometallurgical processes namely ferronickel smelting or matte smelting. So, we can draw such a conclusion that using nickel oxide ores to produce ferronickel will become more and more important .Before used to make stainless steel or other materials, the ferronickel need pretreatment to remove impurities especially sulphur and phosphorus that will cause negative influence on the properties of steel product. Red mud is a by-product during alumina production. Usually, about 1 to 1.5 tons of red mud will be produced when we get 1 ton of alumina. About 90 million tones of red mud are produced every year in the world [2].Red mud is deemed as a toxic industrial waste which needs treatment before discharge because of alkalinity and chemical and mineralogical properties. Until now, the main means to deal with red mud are to store it in impoundments or dump it in the sea depending on local environment. Nowadays, how to recycle red mud has become a pretty hot topic around the world. The last 40 years have witnessed a lot of patent applications concerning the ways of red mud utilization. However, a little amount of red mud is consumed until now due to the limitations of recycling red mud."

Jan 1, 2012

By T. K. Akopyan, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"A qualitative and quantitative analysis of the new Al-Ca-Mn-Fe phase diagram in the region of the aluminium corner is carried out using both thermodynamic calculations and experimental methods. Using the obtained data, the principal possibility of creating both cast and wrought sparingly alloyed aluminium alloys with calcium, manganese, scandium and zirconium at allowable iron contents of up to 0.4% that do not require solution treatment and quenching is justified. At the selected concentrations, the entire amount of manganese (1%) is practically included in the aluminium matrix, while calcium (~2%) and iron are in the multiphase eutectic, which has a fine structure. The joint introduction of 0.25% Zr and 0.1% Sc into the alloy leads to precipitation hardening due to the formation of the L12-Al3(Zr,Sc) phase during annealing. Based on the experimental data for the model multicomponent Al2CaMnFeZrSc alloy, it is shown that such alloys can combine high mechanical properties and good manufacturability during both casting and metal forming. This is due to the combination of a narrow temperature range of solidification with a fine eutectic structure.INTRODUCTION Hardening in branded aluminium alloys (both cast and wrought) is generally achieved by heat treatment of the T6 type, including quenching and artificial aging (Zolotorevskiy, 2007; Kaufman, 2004; Mondolfo, 1976). Heat treatment significantly increases the cost of the final products. Therefore, industrial companies are interested in developing alloys that can be hardened to the desired level without quenching. To solve this problem, alloys with scandium are the most suitable (Toropova, 1998; RØyset, 2005). This element (usually in an amount of ~0.3%) is one of the most effective hardeners in aluminium alloys, due to the formation of Al3Sc (L12) phase secondary precipitates, the size of which is less than 10 nm (Knipling, 2010; Fuller, 2005). These nanoparticles are formed during the annealing via decomposition of the supersaturated aluminium solid solution (hereinafter referred to as (Al)). This feature allows us to significantly increase the strength of aluminium alloys by simple annealing (at ~300°C), i.e., without heat treatment, including quenching. However, scandium is a very expensive metal, so its use as an additive is severely limited. The most effective method is the introduction of scandium together with zirconium (Lefebvre, 2009; Booth-Morrison, 2012). The optimal combination is the introduction of ~0.1% Sc together with 0.20–0.25% Zr, which, according to (Belov, 2006), gives approximately the same strengthening effect as the introduction of 0.3% Sc."

Jan 1, 2018

By M. A. Gomez, V. Yahorava, J. A. Strauss

"It is accepted widely that pressure oxidation (POX) is the most appropriate technology for processing of arsenic containing refractory gold ores. However, studies on the stability of various iron-arsenic precipitates formed during POX are limited. Since the behaviour of these phases could have significant practical implications for gold processing plants, it is important to study them in isolation. This paper compares two synthetic precipitates, basic ferric arsenate sulphate (BFAS) and basic ferric sulphate (BFS) in terms of their formation, behaviour during hot curing and cyanidation, as well as their environmental stability. BFS and BFAS were synthesised hydrothermally at 205°C and their mineralogy was confirmed using various techniques. During synthesis, the addition of H3AsO4 into an aqueous Fe2(SO4)3-H2SO4 mixture significantly decreased the iron yield to BFAS in comparison to BFS under equimolar initial iron and acid concentrations. The BFAS dissolution kinetics was slightly faster, as compared to BFS, during subsequent hot curing. Cyanidation test work on the washed synthetic precipitates indicated that the lime consumption of BFAS was three times lower in comparison to BFS, while cyanide consumptions were comparable. Fresh BFS and BFAS precipitates, as well as their cyanidation residues, were found to pass the respective environmental tests in terms of arsenic release.INTRODUCTION Pressure oxidation (POX) is generally viewed as the most appropriate technology for the processing of arsenic-containing refractory gold ores due to the stabilisation of arsenic in the leach residue (Dutrizac & Jambor, 2007; Gomez et al., 2008; Harris, 2003; Collins, Berezowsky, & Weir, 1988). Detailed laboratory studies indicated that several Fe(III)-arsenate type compounds may be formed under typical conditions of autoclave treatment of refractory gold ores (Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2010; Gomez, Becze, Cutler, & Demopoulos, 2011). The basic ferric arsenate sulphate (BFAS) phase (Gomez et al., 2008), also known as Type II ferric arsenate (Swash & Monhemius, 1994) or Phase 3 (Dutrizac & Jambor, 2007), is one of the most common arsenic-bearing products (Harris, 2003; Dutrizac & Jambor, 2007). BFAS precipitation is viewed as one of the best routes for arsenic stabilisation and performed equally well to scorodite during environmental stability tests (Harris, 2003; Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2011)."

Jan 1, 2017

By C. A. Lavery

A DISCUSSION is presented of natural gas production and field processing equipment as now utilized in the gas producing areas of the United States, with reference to use of such equipment in Canadian gas areas. The scope of the paper is confined to a general description of various types and methods of using surface production equipment. The discussion is divided under two general groups: well-head production equipment, and field processing. The first will be concerned primarily with indirect heaters, separators, knockouts, and special versions of this equipment. The second major group includes the field processing equipment for handling natural gas. A delineation should be made here as to the meaning of field processing as used in this discussion. We will limit our term to mean such processing equipment as may be used in producing fields to process gas or its by products in a manner that does not require conventional plant practices either in operation or supervision. This covers such equipment as is necessary to complete preparation of gas for sale to pipeline and/ or is necessary to recover valuable components. Under this heading we will discuss glycol dehydration, solid desiccant dehydration, low-temperature separation, mechanical refrigeration, and desorbtion-stabilization. These are all processes involved in preparing gas for final sale or disposal. They do not include the more conventional and large-scale plant process systems.

Jan 1, 1956

By R. M. Graves, C. B. McKenzie, D. Barbour, D. W. Desnoyers

"Abstract -The prospective Tulks volcanic belt hosts five significant massive sulfide deposits, Tulks Prospect, Tulks East, Jack's Pond, Daniel's Pond and Victoria Mine, as well as numerous showings and indications throughout its 70 km outcrop length. Regionally, the 498 Ma sequence consists dominantly of felsic pyroclastic rocks and flows with interbedded mafic volcanic units and fine­ grained sediments, commonly graphitic. Contemporaneous granitoid rocks occur in the south half of the belt. Rocks usually display a strong NE-SW, steeply dipping, penetrative foliation and other shear-related high-strain fabrics. Facing directions are normally northwest, although there is local evidence of folding. Sulfide bodies and their alteration systems are deformed and shape-modified in the style of ambient strain.The Tulks, Tulks East and Jack's Pond prospects appear to occupy a similar stratigraphic level, on or near the contact between a thick felsic pile and an overlying broad, conductive package of graphitic sedimentary rocks. AU are pyritic deposits with well-developed footwall alteration systems. The Tulks prospect comprises four polymetallic lenses totalling 750 000 t. Three lenses constituting more than 6 000 000 t of sulfide mineralization are indicated at Tulks East but only the 210 000 t ""B"" lens contains significant base metals. Jack's Pond consists of a very extensive, zoned alteration complex in which four lenses of massive to semi-rnassive pyrite + chalcopyrite are known.The central part of the system, characterized by Mg chlorite and carbonate, is enveloped by pervasive sericitization and capped by intensely silicified and pyritized volcanics. The sulfide lenses are interpreted as part of the footwall zone and are beneath that part of the system most likely to host polymetallic massive sulfides.Daniel's Pond differs from the other prospects in such fundamental ways as metal content, associated alteration and structural setting. The deposit comprises strongly tectonized, Ag-rich, Zn-Pb mineralization distinguished by a pronounced Ba-As-Sb signature. Mineralization is confined to a narrow, north-south high-strain zone which separates unstrained mafic volcanic rocks to the east from well-foliated felsic rocks. The deposit Jacks an extensive alteration halo and at its north end is associated with a lens of barren, undeformed massive pyrite.The Victoria Mine deposit, the most cupriferous of the five, is related to a moderately dipping structure that separates well-foliated Tulks volcanic rocks from an overlying, Jess deformed volcanic­ sedimentary sequence that may be as young as 462 Ma. The structure is also the locus of black chlorite, dolomite and quartz alteration. Structurally remobilized precursor sulfide mineralization is one possible source for the deposit."

Jan 1, 1993

By C. R. Machado

Sossego Mine was the first Vale SAG mill operation to process copper-gold ore. It is located in the state of Para, in the south-eastern Amazon region of Brazil. In the first six years of continuous operation, Vale investigated different alternatives for improving circuit performance by investigating operating conditions, mainly focusing on the SAG mill. Today, after a steady increase over five years the annual production rate seems to have stabilized. It is hoped this work will show how the SAG operating practice have been perfected with time and as new data are collected. Historical data of mill grind-outs and crash stops helped create operation curves depending on the ball charge volume and total charge volume. Also noted were impacts on throughput due to the effect of reducing liner weight and the ore type characteristics.

Jan 1, 2012

By R. N. Chakravorty

Early detection of spontaneous combustion is of utmost importance in underground coal mining to prevent major disruptions of production and to ensure a safer working environment. This paper presents the work done in developing a suitable system for the early detection of heating in a hydraulic coal mine. Laboratory studies on the products of oxidation for Balmer 10 seam coal showed that a significant amount of carbon monoxide is produced during the early stages of heating and that detection methods based on the analysis of other gases, such as hydrogen, ethane or ethylene, are not a better alternative for this coal. The four-point carbon monoxide monitoring system recently installed at the hydraulic mine is discussed in this paper. It is believed that by studying the trend of carbon monoxide concentration in the mine air, it will be possible to detect heating at an early stage. Field tests carried out so far have indicated that infra-red technology will prove to be a powerful tool in the hydraulic mine, particularly for locating hidden oxidation or fire in cracks, fissures, underground workings and coal outcrop areas before it spreads extensively. The project is jointly sponsored by EMR, CANMET, Mining Research Laboratories and Kaiser Resources Ltd.

Jan 1, 1978

By M. Courtin, D. Berthelot, M. Haggis, D. McClarty, R. Payne

Over forty years of uranium mining in the Elliot Lake region of Ontario (1956–1996) has resulted in the production of over 300 million pounds of uranium. With the completion of mining activity, Rio Algom Limited and Denison Mines Limited are utilizing progressive environmental technologies and management systems to reduce and manage the environmental risks associated with the 150 million tonnes of potentially acid-generating tailings in nine regional waste management areas. Water covers designed to reduce oxygen entry and, thereby, significantly inhibit acid generation, have been applied at six of the sites with the Quirke site serving as a demonstration site for the Mine Environmental Neutral Drainage program. All five of Rio Algom Limited’s effluent treatment plants are monitored and controlled from a central control station utilizing a Supervisory Control and Data Acquisition (SCADA) system based on “Fix Dmacs” technology. Scheduling, auditing and reporting of plant operating and environmental monitoring programs for the entire watershed are controlled utilizing the Regional Environmental Information Management System (REIMS). Proper application of these technologies and management systems facilitates delivery of cost-effective environmental monitoring, care and maintenance programs at these sites and provides tools to demonstrate compliance with all environmental performance criteria.

Jan 1, 1999

By Lionel C. Piuze

Introduction and Early History The British Canadian Mine is one of four operating properties of Asbestos Corporation, Limited, and is located in the town of Black Lake, Que., five miles southwest of Thetford Mines. In the early days of as1bestos mining, this .property was owned by a few small companies who later became part of the Asbestos Corporation. First .to commence mining operations on the property was the Coleraine Mining Company who, in 1885, began selling part of their large holdings in the area to various asbestos mining interests. Of these, the earliest active companies were Manhattan United Asbestos, the Glasgow and Montreal Asbestos Company, and the Anglo-Canadian, the last named later becoming the Standard and Dominion Asbestos Companies. Extraction of fibre was limited to what is now known as crude asbestos and the methods were primitive. Drilling was done .by hand and the ore was lifted by derricks operated by band winches. These were later replaced by horse power, but it was not until 1887 that the first steam-operated boom derricks were introduced, at the Anglo-Canadian mine. The ore was hand cobbled and the asbestos roughly classified and bagged. The waste rock, which by today's standards contained a considerable percentage of marketable fibre, was dumped near the pit. The first attempt to separate the asbestos from the host rock by mechanical means was made in 1888 by the G1asgow and Montreal Asbestos Company, then known as the Scottish-Canadian Asbestos Company, whose mill, erected in that year, was the world's first asbestos mill. Though the equipment was crude, the principles employed were the same as those used today with much larger units. The next steps were the use of rock drills, the adoption of steam rail transportation for moving mill rock, and conversion to the more flexible cable-derrick hoisting.

Jan 1, 1950

By M. P. Sinha, Rashmi, Tata Steel Ltd., S. Jaiswal, A. Bhatnagar, P. Garg

Reagents form a crucial part of flotation process as they have the power to control the surface properties of minerals. In case of coal flotation, collectors and frothers are two the important and commonly used reagents. But other types of reagents such as promoters, modifiers and depressants are also finding wide applications because of their availability to improve selectivity and increase recovery. Because of these chemicals the scenario has changed from flotation being used mostly for high rank hydrophobic coals to low rank, oxidised or inferior coals. In the present work a case is presented in which two non-ionic surfactants (abbreviated as A & B) known to act as emulsifier have been studied to get a better flotation performance for a preparation plant with varying feed characteristics. Laboratory flotation tests were conducted with both the surfactants using three feed samples of the plant by varying the dosage at three different levels. The highest combustible matter recovery (more than 80%) was obtained for surfactant B at a dosage of 75 ppm (parts per million) for feed 1. But at the same dosage the recovery decreased by 21% and 10.2 % respectively for feed 2 and 3. On the other hand surfactant A showed a consistent result for all the three feed samples giving the highest value at a dosage of 50 ppm followed by a decrease beyond this point. The tests were complemented by contact angle measurements that demonstrated the same trend. In addition to this the reproducibility of data for Surfactant A was checked and found that the standard deviations for both separation efficiency and combustible matter recovery were within the permissible range (less than 5%). Finally an in-plant process optimization study to evaluate the performance and applicability of surfactant A at industrial level was done and has been discussed.

Jan 1, 2016

By I. L. Sills

Introduction So many minerals and mineral products are used in the glass industry that it would require an unduly long paper to deal adequately with all of them. Only those that go to make up the batch for the more common types of glass will be discussed here, and even with these only, the list is a lengthy one. It is true that for the body of the glass comparatively few materials are required-as silica sand, soda-ash, lime, and feldspar. The others are used mainly to colour or decolorize the glass, or to give it some other desired characteristic, such as high lustre, greater physical strength, or opalescence; but, although they may be present in very small quantities, they are just as in-dispensable to the glass industry as are the main constituents of the batch. Sand Sand is essentially quartz, the dioxide of silicon, Si02. Most glass contains from 71J to 75 per cent silica. Sand for use in the glass industry, or 'glass sand', is obtained both from deposits of unconsolidated material, commonly referred to as 'sand', and from solid rock-sandstone, quartz, or quartzite. For the manufacture of glass, the material must possess a high degree of purity, as noted below, so that, although sand is widespread in most parts of the world, and sandstone, quartz, and quartzite are not at all uncommon, it is only in certain places that suitable deposits are found. At the present time, most of the glass sand used in Canada is imported from France, Belgium, and the United States. The French material, from Fontainebleau, near Paris, is known the world over as a very high quality glass sand. That from Belgium is nearly as good and is lower is price.

Jan 1, 1934