Search Documents

By Frank W. Cole, Sharanjit S. Dhillonn

A new method has been developed for calculating flowing bottom hole pressure in a gas well, using as a basis the general energy equation. Fundamentally, the method shows that a plot of flowing pressure versus depth for a gas well can be represented as a series of incremental .straight lines, with the accuracy in-creasing as the number of increments increase. It is shown mathematically that for most cases the slope of the flowing pressure versus depth curve is essentially constant, in which case a single calculation based on surface conditions will yield acceptable results. In all cases studied no more than two iterations were required for very good accuracy, and in most cases only one iteration was necessary. Several example calculations are shown and the results are compared to other commonly used methods of calculating bottom hole pressures These examples show that the method provides answers which are at least as accurate as other methods usually used, and results in a considerable reduction in computation time.

Jan 1, 1960

By Qin-yong Ma, Jing-shuang Zhang, Bo Han, Pu Yuan

In order to improve the utilization rate of blasthole and blasting effect in vertical shafts, 5 kinds of millisecond blasting model tests with three circle vertical blastholes have been conducted in various delay times with concrete as model material. The blasting effects of millisecond blasting model tests are investigated from cutting volume, cutting depth, and blasting fragmentation, then a reasonable delay time is obtained. In the middle of concrete model, there are 4 blastholes uniformly distributed in the first circle, 6 blastholes uniformly distributed in the second circle, and 10 blastholes uniformly distributed in the third circle. Each blasthole is charged with one millisecond delay electric detonator, and the rest is blocked with stemming. The depth of blastholes in the first and second circle is 180mm, which is 20mm deeper than those in the third circle. After initiation, the blasting cavity is cleaned up, then the cutting volume and cutting depth are measured. Meanwhile, the blasting fragments are gathered and have analysed by function Rosin-Rammler. The test results show that when the inner two circle blastholes initiated simultaneously and the third circle blastholes initiated with millisecond delay, the reasonable delay time is 50 ms. At this time, the cutting volume and cutting depth of blasting model are 3920 cm3 and 68 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 53.2 mm and 74.6 mm respectively. While when all three circle blastholes initiated with millisecond delay, the reasonable delay time is also 50 ms. At this time, the cutting volume and cutting depth of blasting model are 10705 cm3 and 118 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 51.0 mm and 81.7 mm respectively. The researches indicate that for millisecond blasting with multiturn blastholes, the reasonable blasting scheme is multiturn blastholes initiated in millisecond delay and the reasonable delay time is 50 ms.

Jan 1, 2015

By X. S. Fan, T. R. Feng, D. Chen

To meet the flotation process requirements, the large-scale flotation cell must be designed for sufficient pulp mixing, reasonable air dispersion and solid suspension, which is very difficult to design for super large-scale flotation cell. Hence, the flotation cell scale-up and optimization for a short period is a challenge for super large-scale flotation cell design. Computational fluid dynamics simulation has been applied in flotation cell study, which is effective, timesaving and low cost in the study of the flow field distribution for super large-scale flotation cell. This paper demonstrates the flow field characteristics in the 600m3 flotation cell by CFD. The flotation cell model is meshed with hexahedral grid and the high mesh quality assures the computational precision. MRF model, namely a steady-state approximation, ensures that individual cell zones can be assigned different rotational speed. Euler-Euler approach is chosen for multiphase flow simulation to treat different phases as interpenetrating continua. Numerical simulation of single phase, two-phase and three-phase are investigated respectively. Results suggested that the flotation cell has the apparent upper and lower flow circulation. In condition of the impeller rotation, the air is dispersed reasonably. In addition, the solid phase volume concentration distribution in the cell has a little difference.

Jan 1, 2015

By Ralph H. Cleland

GENERALLY speaking, the Industry lost ground in 1941 in its accident experience. Though the frequency of compensation accidents was but slightly higher than in the previous year and well below past experience, our fatality rate shot up to that obtaining in 1938, and the average cost per man employed was the highest for some time. The number of fatalities was 56 in 1941 as against 33 in 1940. The average cost of compensation per man employed was $34.25 in 1941 as against $28.43. There was but a slight increase in the number of men employed. Accident prevention efforts were maintained, as shown by our frequency, but our accidents were of a more serious nature. In a period of considerable labour turnover, with many new men entering the Industry, especially the base-metal division, and much mental distraction, we might well have expected a high rate of accidents. That this did not occur is a tribute to managers, supervisors, and workmen alike. We all regret the high fatality rate and one must consider why this occurred. So far as it is possible to determine, there is no apparent explanation. There were no disasters. The accidents occurred to the same class of work-men, both in respect to jobs and age groups, and from the same age-old causes that we all know so well. Luck is a big factor in the seriousness of an accident; the solution lies in preventing accidents, even first-aid cases. Generally speaking, if minor accidents do not occur, major accidents do not occur.

Jan 1, 1942

By Paul W. Kingston

In New Brunswick, during the 1970's, rocks of the Lower Carboniferous Windsor Group in the Moncton Basin of the Fundy Epieugeosyncline have been the target of intense exploration and drilling programs. Sylvinite ore was discovered in three structural basins of the Moncton Basin near Sussex through a drilling program sponsored jointly by the Federal Department of Regional Economic Expansion and the New Brunswick Department of Natural Resources. In 1973, exploration and development rights to the western end of the Moncton Basin were awarded to the Potash Company of America. One high-grade sylvinite unit, varying between 15 and 70feet in true thickness, with a strike length in excess of 5 miles, is located near the stratigraphic top of the assymetric, semi-diapiric, locally overturned anticline. Late in 1975, exploration and development rights to the Marchbank Syncline were awarded to International Minerals and Chemical Corporation (Canada) Limited. To date, a stratigraphic evaporite sequence, forming the semi-diapiric core of the syncline, has been shown to contain one major high-grade sylvinite unit averaging 70 feet in true thickness over a strike length in excess of 2 miles. Both properties appear to have potential considerably in excess of that revealed by the exploratory drilling, and both, because of numerous mineralogical, structural and stratigraphic similarities, are thought to be depositionally contemporaneous. Both potash deposits lie within 50 miles of the Saint John all-weather deepwater port, thus affording easy access to eastern and mid-western U.S. markets. Further opportunities for potash exploration in New Brunswick are considered excellent, as there are large untested areas with favourable geology and known potassium water anomalies and negative gravity anomalies occurring in the Moncton and Cumberland basins, and in the Central Basin of New Brunswick.

Jan 1, 1979

"Shales play a major role in the stability of slopes, both natural and engineered. This paper attempts to provide a review of the state-of-the-art in shale slope stability. The complexities of shale terminology and classification are first reviewed followed by a brief discussion of the important physical and mechanical properties of relevance to shale slope stability. The varied mechanisms of shale slope stability are outlined and their importance highlighted by reference to international shale slope failures. Stability analysis and modelling of anisotropic rock slope masses are briefly discussed and the potential role of brittle rock fracture and damage highlighted. A short review of shale slopes in open pits is presented.INTRODUCTIONShales have been stated to form approximately 58% of sedimentary rock so it is not surprising that they are frequently encountered in both natural and engineered slopes. They represent challenging environments for slope stability due to the wide variation in their engineering properties, their changing behaviour with time due to geomorphic processes and the variation in the failure mechanisms as a function of both stratigraphy and tectonics. An extensive body of literature exists on the terminology and classification relevant to shales; it is not possible in the scope and length of the current paper to review these works in detail and the reader is referred to Farrokhrouz and Asef (2013), Bell (2000) and Goodman (1993) for detailed discussions. It is arguably the case that no universally accepted classification of shales exists today and depending on the field of application the terminology varies widely. Shales in slope stability, for the purpose of this keynote paper, are taken to include material varying in properties from weak rocks to soils and therein lies one of the most challenging aspects in shale slope characterisation for engineering purposes. They have been classified as “rock-like” or “soil-like’, (Underwood 1967) or compacted and cemented, Table 1, Yagiz (2001). Classifications have considered numerous factors including composition, cementation and a wide range of engineering properties.The propensity of shales to degrade with time due to geomorphic processes has resulted in an important aspect in their classification, that is, the attempts to incorporate slaking, durability and swelling and softening behavior through purpose developed testing methods (Gamble 1971, Morgenstern and Eigenbrod, 1974). Figures 1 and 2 show examples of terminology used to describe argillaceous materials and some proposed engineering classification schemes (Grainger 1984 and Bott 1986). Corominas (2014) provides a recent classification of argillaceous rocks and their durability relating five stages of slope deterioration to the texture of the rock on Ternary diagrams. No attempt will be made here to discuss the merits of the proposed terminology and classifications, suffice it to say, that the controversy and flux surrounding these issues is a strong indicator of the complexities in the behavior of these materials. In this paper the author will consider slope stability in the materials indicated in Table 1, Figures 1 and 2 without undue focus on terminology. At the lower strength limit of shales the engineer must design slopes using the principles of soil mechanics which may vary from the simple Mohr Coulomb plasticity constitutive criterion to modified critical state models, some even attempting to incorporate softening behaviour in the weaker clay shale materials. Given the transitional nature of shale materials several workers have treated overconsolidated clays and clay shales using concepts such as peak and residual shear strength, brittleness index and softening. Martin and Stacey (2013) provide a useful review of the importance of weak rocks in open pit mining, with mudrocks as a specific member, and note the importance of delayed failure, progressive failure and loosening in the stability of"

Jan 1, 2015

By A. A. de Gast, R. B. James

"The metal content of ore blocks can be calculated by the use of many different methods. These methods range in sophistication from manual calculation to computer. oriented techniques. In this case a cubic polynomial regression model is developed to depict the grade distribution of an orebody. Mine production, in stope dimensions, is then simulated on a computer to predict the output of metal content. The volume, grade and variance of the grade are estimated by triple integration and matrix algebra. A case study shows reasonable agreement between the results from the mathematical model and the mine geologists' estimate of production and ore reserve grade and tonnage."

Jan 1, 1972

By V. Polotski

Initiated and financed by the Canadian Space Agency, Micro-Rover Platform with Tooling Arm (MRPTA) project has targeted the development of a robotic system with remote control and autonomous navigation capabilities for testing a large variety of analogous planetary missions. Although developed for planetary exploration, the navigation system is highly suitable to such areas of application as construction and in mining. Autonomous navigation system is capable of moving the platform to predefined position(s)/orientation(s) while continuously mapping the terrain, assessing its traversability and choosing most appropriate path to follow. Designed according to the JAUS (Joint Architecture for Unmanned Systems) framework, the system consists of several interconnected components. Following components are of particular importance: Pose Estimator (PE), Terrain Evaluator (TE), Map Manager (MP), and Path Planner (PP). The PE uses a minimal sensor configuration consisting of an azimuth gyroscope, inclinometer and wheel odometry. The PE provides reliable pose estimates in spite of pronounced slippage by employing extensive use of fused data. The TE uses a nodding laser scanner which continuously sweeps the area in front of the platform and constructs a ?traversability grid? (TG) of the surrounding area. Multiple TGs are constantly constructed along the platform motion path are combined into a terrain map maintained by the MP. The PP uses this map to compute a motion path Obtained path is executed by the motion controller and remains current until it is contradicted by the most recent map ? at which point it is re-planned. This paper addresses integration issues, lessons learned and also outlines the possible applications for construction and mining.

Aug 1, 2013

By Sub-Committee of the Committee on Research

"THE FOLLOWING REPORT was compiled by a sub-committee of The Metallurgical Society of CIM, Committee for Research, and represents a viewpoint of the steel industry in Canada. The objective was to define those areas in which the industry considers that external sources of Research and Development are a necessary function in supporting the in-house R & D conducted by the industry.On future occasions, the viewpoints of other metallurgical industries, such as those of nickel, copper and aluminum, will be presented. The report is divided into several sections: 1.-R & D Spending by the Steel Industry (a) Memberships in Recognized Steel Research Centres (b) Memberships in Recognized Industry Associations (c) Sponsored Research at Recognized Centres (d) Sponsored Research at Universities(e) Sporadic Research 2.-Areas for Research and Development(a) Instrumentation (b) Environment Control (c) Refractories (d) Sponsored Research at Universities(e) Electric Furnaces (f) Continuous Casting"

Jan 1, 1970

By M. Holmes, R. Molnar, E. Norton, K. Baxter, J. Riordan

The Boleo Copper-Cobalt-Zinc-Manganese Project of Baja Mining Corp. is situated adjacent to Santa Rosalia on the Baja Peninsula of Mexico. The El Boleo ore is a mixed oxide-sulfide deposit with major values in copper, cobalt, zinc and manganese. The metallurgical process designed to treat the El Boleo orebody involves a sulfuric acid leach in seawater using oxidative and then reductive leaching to maximize metal extraction. The leach solution is separated from the barren solids via counter current washing through a series of high rate thickeners. Copper is recovered using conventional SX-EW processing as cathode. Zinc and cobalt are extracted from the copper SX raffinate after iron and aluminum precipitation. The CSIRO DSX solvent system (Versatic® 10 and LIX® 63 mixture) are used in this extraction. Manganese remains in the DSX raffinate and is recovered by soda ash addition as a high quality manganese carbonate precipitate. Zinc and cobalt are acid stripped from the loaded DSX solvent. Zinc is then re-extracted away from cobalt using Cyanex® 272 extractant and stripped into a highly concentrated strip liquor (+100 g/L Zn) and directed to either a spray dryer or a granulator for production of zinc sulfate monohydrate. The zinc solvent extraction raffinate, containing cobalt, advances to another SX circuit using Cyanex® 272, for the recovery of cobalt as cobalt cathode. In this paper, the detailed results from bench and integrated pilot plant testing for zinc recovery from the El Boleo ore will be described. The results of this testing are currently being used to engineer the commercial plant at El Boleo.

Jan 1, 2008

By D. P. McDonald

"IntroductionTHE PURPOSE of this paper is to present .a summary of the evidence given before the Petroleum and Natural Gas Conservation Board in support of applications to it for permits to export natural gas from Alberta.I will attempt to be objective in my statements, despite the fact that my main interest in the hearings before the Board was to advance the interests of my own clients, the Westcoast Transmission Company, Limited.The hearing of the export applications •commenced before the Board in January, 1950, with the .application of the Westcoast Transmission Company. Joint hearings were commenced in September, 1950, and completed on December 14th, 1951. The Board heard evidence in support of six applications for export, one application to build a gathering system in Alberta, and three interveners, the .latter being the City of Calgary, the local gas companies, .and the coal interests, including both operators of coal mines and the Unions.The evidence comprised better than 8,400 pages, over two million words, and occupied 92 days before the Board.The Interest in Natural GasThe natural gas industry is one of the newer industries. It is not yet twenty years •old. In the United States, the expansion •of pipeline facilities has been phenomenal in the last fifteen years, and particularly in the last three years, when a total of over two billion dollars was invested in pipeline facilities. There are approximately 250,000 miles of gas transmission pipelines in the United States at this time, with additional lines constantly being pressed."

Jan 1, 1952

By J. M. Cummings

CONSIPERABLE information on the industrial or non-metallic mineral resources of British Columbia has been published. For a general resume of the subject, reference may be made to a paper presented by A. M. Richmond before the Annual General Meeting of the Institute in 1935 (1). To avoid duplication, the present paper is confined to a discussion of the existing industrial mineral industry of the Province and of the factors governing its present and future development. British Columbia's mineral production in 1936 had a value approximately 15 per cent of that for the whole of Canada. Preliminary estimates for 1937 indicate that this proportion has been maintained, although the totals have increased about 25 per cent. The following table presents comparative figures, for the year 1936, illustrating the relative importance of the major divisions of the mineral industry in British Columbia and in Canada as a whole.

Jan 1, 1938

By Rob Boom, Yasuyuki Tozaki, Greg Traquair

The objectives of the business case are to examine a proposed metallurgical project and answer fundamental questions about project feasibility, risks, opportunities, and value. A business case fulfills these basic functions: estimates economic value; helps to understand competitiveness; serves as a risk management tool; and serves as a communication tool. A business case evolves with the project life cycle, and supports the gate reviews at the end of each phase of engineering, through to project construction and operations. A business case must be holistic, including all elements of scope that can impinge on project risk and value.

Jan 1, 2015

By B. G. Hunt, E. J. Kwasney, W. P. Campbell, S. L. Gertsman

"AbstractIn the separation of lead and zinc concentrates from the ore from Cominco's Sullivan mine at Kimberley, • B.C., an iron sulphide concentrate is also produced, some of which is roasted to provide sulphuric add for the manufacture of phosphate fertilizer. The iron oxide calcine from the roaster is potentially a valuable raw material for the production of pig iron and steel. To evaluate this material, six tons of .pig iron was produced from it in an experimental 75 k.w. electric furnace at Trail. The pig iron alone, and also in varying proportions with structural steel scrap and commercial pig iron, was used in the production of basic electric furnace steel at the Mines Branch Laboratories, Ottawa. Details are given of the steel making and fabrication procedure, of the visual and microscopic examination, and of the extensive series of tests on the steel produced. The steel produced using Cominco .pig iron in the charge showed normal working properties in all tests carried out.IntroductionTHIS PAPER describes (a) experimental work by The Consolidated Mining and Smelting Company of Canada, Limited ( Cominco), at Trail on the production of pig iron .from Sullivan iron concentrates, and (b) a joint laboratory investigation by Cominco and the Mines Branch, Department of Mines and Technical Surveys, Ottawa, to determine the feasibility of making a satisfactory steel from this pig iron."

Jan 1, 1955

By R. Holmwood, M. Faris, P. Holloway, M. Collins

Sulphuric acid addition is a major driver of the economics in the processing of nickel laterite ores by high pressure acid leaching (HPAL). Understanding the optimal acid addition rate is essential for the success of any HPAL operation, and this is especially true at Ambatovy, where the composition of the feed tends to vary significantly on a day-to-day basis. Most studies on the effect of acid on nickel extraction in HPAL have used laboratory testwork as their basis. Although these studies are invaluable in assessing the economics of a new project, they are limited by the range of ore composition that can be tested and the differences between the operation of the laboratory equipment and the commercial plant. To enable optimization of the acid addition at Ambatovy, operating data from the HPAL operation were obtained using OSISoft’s PI system and the data from several periods were examined to develop relationships between acid addition and nickel extraction. The initial relationships from 2014 focused on the acid required to achieve a target nickel extraction of 95%, with aluminum and magnesium in ore and feed slurry solids content as the major variables. As Ambatovy ramped up through 2015 and 2016, the calculated acid requirement was further refined to address the effects of HPAL temperature and retention time, and the oxidizing/reducing characteristics of the ore, and to generate acid requirement relationships as a function of ranges of nickel extraction. These relationships supported raising the target nickel extraction to 96% and enabled the development of an economic model between acid addition and nickel extraction.

Jan 1, 2017

By R. White, C. Doyle, B. Martin, C. Díaz, J. Hrepic, G. Cuthbert

"A program initiated to improve the service life of the magnesite-chrome refractory in the top blown rotary converters at INCO’s Copper Cliff Nickel Refinery identified slag corrosion as a major wear mechanism. Target slag compositions were established to produce a non corrosive slag. A plant program to achieve this target slag by the addition of controlled amounts of do lime and MgO was instituted. Addition to rates of the slag modifiers was optimized based on the slag composition assays achieved and the requirement to address corrosion effects on the high alumina content ladle refractory. A60% gain in TBRC refractory performance was eventually achieved and has been maintained yielding a net annual savings of $700,000. A significant gain in available converter operating time has also been realized.IntroductionINCO’s Copper Cliff Nickel Refinery utilizes two top blown rotary converters (Fig. 1) to smelt a blend of semi-refined nickel concentrates, producing a granulated nickel matte suitable for the adjacent carbonyl based nickel refining operation. The converter, or TBRC, operation is a batch process composed of feed charging and melting, oxidation of the excess sulphur in the matte, and reduction of residual nickel oxide. The final matte, containing about 78% nickel, is tapped at 1600°C from the converter and is granulated in a sluice equipped with high pressure water jets."

Jan 1, 1997

By H. Wilton Clark

"IntroductionTHE CANADIAN use of short-period delay-action detonators in coal shooting has been carried on for about two years, mostly in British Columbia, and this is a preliminary report on progress to date. Entire coal faces are being shot successfully with one application of electric current.The electric blasting cap came into use about the beginning of the century. The low-tension electric cap, the type most commonly used, consists essentially of a metal tube containing an initiating explosive. Two wires lead into the end of the cap and are connected inside the cap with a short 'bridge wire .of very high resistance. This •bridge wire is buried in a match-head of a readily ignitable powder composition. When current goes through the lead wires, the bridge wire becomes extremely hot and sets• off the match-head which, in turn, ignites the powder just below it in the tube. This explosion sets off the main charge of explosive. Thus, by connecting a group of caps to a source of electric .current, a number of charges could be exploded simultaneously. This immediately became of great value to mine and quarry operators. Explosives could now be used to break up large masses of material at one time, as against the older, slow method .of blasting small amounts with single charges.The next step was to develop a delay detonator which would allow charges of explosive to fire one after the other, one or two seconds apart. Such detonators allowed first blasts to relieve some rock burden before the next charge fired, giving the second charge an easier task in forcing out more rock, and so on for the rest of the series of charges."

Jan 1, 1953

By E. R. Hughes

Introduction Situated 182 miles east of Vancouver, on the Kettle Valley branch of the Canadian Pacific railway, the Princeton coal field is readily accessible to the Coast markets. The area covers approximately forty square miles and present indications are that the deposits should contain at least 300,000,000 tons of coal. Comparatively little development has yet taken place in this coal field. Since the commencement of recorded output, the collieries operating in this area have produced 1,640,518 tons of coal. The coal field proper includes only the Tertiary deposits adjacent to the town of Princeton and does not include the Coalmont or Nicola deposits. Production has never been on a large scale. The largest annual output from any property was 81, 780 long tons mined at the Granby colliery in 1940. Coal output was first recorded in 1909 and since that time fifteen properties are reported to have either mined coal or to have done prospecting or development work; of these, only two are presently active. However, none of the properties now inactive were closed because their coal resources were exhausted. The accompanying key map shows the extent of the Princeton coal field, and the location of the coal mines and prospects in this field General Geology The Princeton field is underlain by rocks of Oligocene age and is one of the series of more or less isolated Tertiary lake basins in which coal, or lignite, has been found in the interior of British Columbia. Resting on the Nicola group rocks of Triassic age, the Princeton sedimentaries consist of sandstones, conglomerates, shales, bentonite, bentonitic clays, and several seams of coal. Tertiary volcanics occur both above and below the stratified rocks and in places they have been thrust through the overlying measures. In some areas, the coal has been burned to a red ash as the result of vulcanism, while in other parts some of the moisture has been driven from the coal, thus improving the grade. The field can best be described by dividing it into two areas: the Southern area, lying to the south of the town of Princeton, where most of the mining has been done; and the Northern area, to the north of Princeton, where very little development has taken place.

Jan 1, 1947

By Edward I. Renouard

"THE mineral industry is constantly undergoing changes and facing challenges, and today we are in the midst of another serious one -namely, manpower requirement at every level in the mines, shops and plants. In the not too distant past we had a situation where labour was plentiful, although the equipment, by present-day standards, was quite inadequate, and that's easily understandable when you look back at the primitive methods by which our Western mines were first developed and operated, and then improved by the inventiveness and ingenuity of man.I'd like to show you a few slides from drawings made by Buck O'-Donnell which illustrate some of yesterday's methods of mining. Some of you probably had first-hand experience with some of these so you know they were tedious, time-consuming and involved a lot of heavy labour.Taking the Anaconda Company operations at Butte as an example, we can see what has happened in just the past ten years. In August of 1956, the Butte mines had 5,516 day's-pay employees and 976 salaried employees, for a total payroll of 6,492. In August of this year, there were 3,645 day's-pay employees and 605 on the salaried roll, for a total of 4,250. The number of contract miners had gone from 1,347 in 1956 to 606 in 1966 and that of other underground miners from 2,893 ten years ago to 1,149 this year. Along with these changes, however, another change of special significance has taken place, and that is in the number of skilled craftsmen, surface engineers and so on required for our operations. In 1966, we had 1,890 of these people, 600 more than in 1956 and nearly three times as many as just twenty years ago."

Jan 1, 1967

By Jaeheon Lee, Junmo Ahn, Isabel F. Barton

"Newmont’s Mike prospect, currently undeveloped, is a blind Cu-Au(-Zn) deposit on the Carlin Trend, containing >8.5 M oz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn as Carlin-type gold and polymetallic Cu-Zn minerals in Paleozoic lower-plate carbonates and shales. This project was undertaken 1) to examine the effectiveness of different lixiviants for leaching the Mike supergene Cu-Au ores via bottle roll tests, and 2) to determine what ore minerals resist dissolution in each leaching agent by comparing the mineralogy and chemistry of head and tail samples. Sulfuric and sulfurous acids were used to leach copper and cyanide was used to leach gold. Thiourea, glycine, and other lixiviants were used to leach both base metals and precious metal. QEMSCAN and SEM study of six samples of different ore types and grades indicate that the Au occurs as varieties of native gold, including auricupride and electrum. Major Cu minerals are native Cu, cuprite, malachite, chrysocolla, and conichalcite (Ca-Cu arsenate), with locally significant Cu in jarosite and goethite. Gangue mineralogy is dominated by quartz, sericite, chlorite, alunite, smectite and kaolinite, K-feldspar, and iron oxides (sensu lato). Results of bottle roll tests and leach residue mineralogy will be presented and discussed at the conference.INTRODUCTION Resource and Geologic Setting The Mike deposit is a large, blind Cu-Au(-Zn) deposit in the Maggie Creek district of the Carlin Trend of Nevada, USA, near the Gold Quarry mine (Figure 1). The mineral inventory, based on drilling, is 8.568 Moz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn at average grades of 0.72 g/t Au, 0.34 wt% Cu, and 2.13 wt% Zn (inventory for a cone at $400/oz Au and $0.80/lb Cu by Norby and Orobona, 2002)."

Jan 1, 2017