Search Documents

By M. Board, R. Pakalnis, S. Seldon, R. Brummer

The Kidd operation mines roughly 10 000 tpd of copper and zinc ore from underground and employs about 700 personnel. In the late summer and fall of 1997, major movements in the proximity of the east wall of the Kidd open pit had been observed. The Kidd pit had been mined from 1965 to 1977 to depths of 260 m (850 ft), followed by subsequent mining by underground methods to current depths in excess of 1830 m (6800 ft). The No. 1 Mine (2600 Level to pit bottom) is approximately 90% extracted, with most of the remaining reserve between 2000 and 2500 levels. Although initial concerns centred on the stability of the pit walls, the potential ramifications of the movements to the underground were recognized and measures were implemented to ensure the safety of personnel as well as to minimize the potential damage to existing operations. In late October, damage to underground operations was observed as deep as the 2000 Level. In the final assessment, the global mobilized mass was a “wedge”-shaped hangingwall block extending from surface to about 610 m (2000 ft) below surface. The “wedge” boundaries are defined by a fault and shear zone which have continuous lengths in excess of 1070 m (3500 ft); its base by shearing through the host rock mass; and its eastern face by deep tension cracks (Fig. 1). Mined and filled excavations at the western face of the “wedge” allowed mobilization of a mass in excess of 30 M tonnes. Movements in excess of 75 cm (30 in.) per day were recorded on the surface stations that preceded the complete shutdown of operations on October 29, 1997. The evaluations in the days following the shut-down were centred on mitigation of immediate and future possible negative impacts on infrastructure and mining of the remaining No. 1 Mine reserves while ensuring the safety of the operators. This effort required the rapid assessment of the potential damage of the block movement on underground infrastructure, stope access, drainage and ventilation, as well as airblast potential due to the falling of a large block into the pit near the ventilation intake at the base of the pit. These assessments were presented in a previous paper (Seldon et al., 1999). In total, the lateral movement of the block on the ground surface was over 4.3 m (14 ft). This paper describes the detailed studies performed to understand the failure mechanism and to assess the impacts on future mining in No. 1 Mine.

Jan 1, 2000

By J. E. Amadi-Echendu, F. Stober, J. Ndlovu, L. R. Nelson

The Polokwane Smelter Complex (PSC) relies on a single 68MW high-intensity six-in-line furnace to smelt a planned 650 000 t/a dry concentrate to produce a platinum group metals (PGM)-bearing matte. As typical of a greenfields venture, considerable attention was paid to the project development and implementation stages of design, engineering, construction and commissioning. Somewhat unusual though, was the role of a dedicated multi-disciplinary "Operational Readiness" and support team, comprising the owners team and specialists from the furnace designer, HATCH, to effect a safe and rapid ramp-up to the design smelter capacity of 68MW. The challenges encountered in developing an effective partnership will be discussed. The modus operandi and roles of the "Operational Readiness" team during the design, procurement, construction and commissioning stages as well as that of the operational support team within the overall ramp-up objective will be presented. The "Operational Readiness" team was responsible for:

Jan 1, 2005

By R A. Burwash

In the Yellowknife geologic province, 2,600-million-year-old granites are cut by three sets of diabase or gabbro dyke : (1) large dykes striking 70°E to E-W, (2) rare dykes striking N-S to 30°E and (3) an abundant swarm striking N 10°-300W. Preliminary potassium-argon dating has been carried out on whole-rock samples of the chilled margins and coarse centers of the dykes, and on mineral separates from the dykes and contact aureoles. Data from seventeen dated samples suggest that the dyke sets were intruded during three periods of basaltic magmatism -2,200, 1,500 and 1000 million years ago. The two earlier periods closely follow the time of emplacement of granites in the Yellowknife and Churchill geologic provinces. The latest diabase dykes occurring in the Yellowknife province are temporally related to a widespread basaltic magmatism, for which the term Keweenawan is not appropriate. D DRING the past ten years, methods of physical age determination have been widely applied to date the time of intrusion or metamorphism of Precambrian rock

Jan 1, 1963

By J. M. Harrison

FIELD PARTIES of the Geological Survey of Canada have, in recent years, mapped several areas east and northeast of Flin Flon (9, 10, 12, 13, 14, 15, 118) (1). In all these areas the mineral deposits show a close geographical relation to faults although the immediate control of most of the known ore deposits appears to be folded structures in the rocks (8, 11, 18, 19). Air photographs and published geological maps were studied in order to ascertain whether or not the mineral deposits in the Flin Flon-Snow Lake mineral belt as a whole show any spatial relationship to faults. It was found that most of them do show a distinct geographical association with faults, or with topographic features that may be faults. It is further apparent on air photographs that a major lineament, for composite of lineaments, follows approximately the contact between gneisses and schists of the Kisseynew complex on the north, and Amisk volcanic rocks on the south. However, this Kisseynew lineament is not continuous and, especially in the eastern half of the district, it is exceedingly irregular in plan. Parts of this lineament have been mapped as faults (9, 10, 12, 14), other parts have been shown as stratigraphic contacts (1, 2, 21, 27), and still other parts have not been studied except by reconnaissance methods. It is suggested that the Kisseynew lineament may be due to a deformed fault that extends easterly from a point about 25 miles west-northwest of Flin Flon to a point at least 10 miles northeast of Wekusko lake and that the mineral deposits.

Jan 1, 1951

By L. O. Thomas

BROADLY, Yukon is divisible into three physiographic provinces which are extensions of the similar divisions in British Columbia that are there known as the Coastal system, the Interior system, and the Rocky Mountain system. South of Yukon to about the 50th parallel of latitude, the Coastal system consists solely of the Coast range, which, in Yukon, passes behind the St. Elias range and for the remainder of its course constitutes the most easterly portion of the Coastal system. The extension, in Yukon, of the Interior system of plateaus and mountains of British Columbia is commonly referred to as the Yukon plateau, and the extension of the Rocky Mountain system as the Mackenzie Mountains system. The Coast-Range province is largely made up of granitic intrusives; the Mackenzie Mountains province of folded sediments; and the intervening Yukon Plateau province of ancient metamorphic rocks, folded sedimentary rocks, volcanics, and intrusives. Almost the entire area dealt with in this article was subjected to glaciation and, in those parts where its full effect was experienced, the valleys were invaded by vast masses of ice which transported and scattered the stream gravels, with their gold content, so that, even where gold still remains in the old stream channels, it has become so buried under boulder clay and other glacial accumulations that it is, in most places, difficult to find, and, when found, may prove very expensive to mine. Most of the present rivers have done little more than cut new channels in the glacial debris, touching only here and there upon the subjacent rocky floor. The territory in Yukon adjacent to the section of the Alaska highway between Watson and Teslin lakes is for the most part unknown both topographically and geologically. From Teslin to Kluane, the highway travels a fairly well-mapped part of Yukon, but beyond that point, until White river is reached, the geology of the adjacent country has, largely, yet to be determined, particularly on the north side of the highway.

Jan 1, 1943

By W. A. Lang

COAL of sub-bituminous rank underlies much of the plains area of Alberta. This coal is geo-logically young, and occurs in Belly River and Edmonton strata of Up-per Cretaceous age. Generally, the seams are flat-lying, but in some areas they may dip as much as 5 degrees. The overburden, composed mainly of glacial clays and sand-stones, may vary in depth from a few feet to several thousand feet. Recovery of the coal has 'been by drift, slope, and shaft underground mines, and by open-pit stripping operations. Production has been obtained from a large number of mines, most of which have been relatively small and with preparation equipment limited to a loading tipple with screening facilities, and a picking belt where high-ash materials can be removed from the larger sizes. The coal has been sold for domestic and industrial space-heating, for production of process steam, and for power generation. In re-cent years competition from natural gas, propane, and oil has seriously interfered with the production and marketing of sub-bituminous coal, especially with the disposal of the smaller sizes at a realistic price.

Jan 1, 1958

By Olli Haavisto, Lauri Koresaar, Navid Khajehzadeh

In recent times sustainable minerals processing is an important topic in research. Sustainable mining is linked with efficient use of energy and human resource in all process stages including beneficiation of the ore. Controlling and optimizing the recovery while preserving the grade of the concentrate is extremely important in flotation plants. This development requires new technological solutions and has given rise to the multitude of application areas for lasers. X-ray Fluorescence (XRF) and Laser-Induced Breakdown Spectroscopy (LIBS) are currently two of the predominant non-contact and direct analysing methods in industry. LIBS and XRF measurement techniques both have high capabilities for measuring elements. LIBS has a very simple and easy-to-implement spectroscopic setup, wider range of elements can be detected with online LIBS and measuring light elements is simpler by LIBS compared with XRF. It is of great interest to extract mineralogical information from the elemental results with no modification on the measurement setup. In order to achieve this, more advanced interpretation of the elemental peaks of LIBS spectra is required. Therefore, the major focus of this research is about measuring mineral concentrations from the elemental lines of LIBS spectra using advanced statistical methods. This accomplishment provides knowledge about mineral concentrations from the real-time assay data of the slurry LIBS analyzer. Consequently, this paper first discusses an analytical method called partial least squares regression leading to rapid mineral identification from the elemental contents of the LIBS technique. Then the technique is employed to analyze the mineral contents quantitatively through the information acquired from an on-stream LIBS slurry analyser. This can lead to many benefits such as rapid control of concentrate quality, enhanced recovery, saving time, energy and manpower.

Jan 1, 2016

By D. C. Peck, James. R. S., Chubb. P. T.

"Abstract -The East Bull Lake gabbro-anorthosite intrusion is one of several Early Proterozoic layered matie intrusions occurring along the Southern Province - Superior Province boundary in the Elliot Lake - Sudbury region, Ontario. The base of the East Bull Lake intrusion comprises abundant plagioclase cumulates (Leucogabbronorite Zone) hosting two distinct styles of sulfide mineralization: (1) disseminated magmatic sulfides, and (2) disseminated to massive, structurally controlled sulfides. Both types of mineralization are enriched in Pd, Pt, Au, Cu and Ni. The host rocks to the sulfide mineralization display a range of interesting features including nodular textures, dendritic­ pegmatitic matie pods, inclusion-rich zones (pyroxenite, anorthosite and granitic inclusions) and mag­ matie breccias. Disseminated chalcopyrite, pyrrhotite and pentlandite occur in concentrations of up to lOOJo within erratically distributed gossan pods near the base of the intrusion. The sulfides were originally precipitated from intercumulus liquids, but were subsequently recrystallized and locally remobilized along fractures during the major period of metamorphism and deformation that af­ fected the East Bull Lake intrusion. The base- and precious-metal tenor of the structurally controlled sulfides can be explained by extensive remobilization and reconcentration of the pre-existing magmatic sulfides in the vicinity of a major shear zone. Both styles of sulfide mineralization locally contain ppm abundances of POE + Au and are generally Pd- and Cu-rich, although both display large variations in Pd :Pt and Cu:Ni ratios. The magmatic sulfides are more strongly enriched in POE and contain up to 1470 ppm Pd in 100% sulfide. Severa! factors, including source characteristics, magmatic processes (crustal assimilation, fractional crystallization) and post-magmatic inter­ action with hydrous fluid, have influenced the present distribution of POE, Cu and Ni in the East Bull Lake intrusion .The magmatic sulfide occurrences from the East Bull Lake intrusion compare favorably with marginal-type deposits from rift-related intrusions (Noril'sk-Talnakh region, Siberia; Duluth Com­ plex, U.S.A.) in terrns of their distribution, but are most similar to reef-type POE deposits with respect to their base- and precious-metal geochemistry. The combination of high POE tenors and large tonnages that is observed for the POE-Cu-Ni mineralization from the East Bull Lake intrusion suggests that a good potential exists for the presence of economie concentrations of Pd, Pt, Au, Cu and Ni in the intrusion. On a global scale, the East Bull Lake intrusion is part of a suite of Early Proterozoic plutons, many of which contain significant volumes of stratiform and/or marginal­ type POE-Cu-Ni mineralization. The East Bull Lake intrusion is also one of the oldest mineralized intrusions derived from a sub-Superior Province mantle source region that has given rise to several significant magmatic POE-Cu-Ni deposits during the period 2.5 Ga to 1.1 Ga."

Jan 1, 1993

By J. O. Pitts

"Background The preponderance of Canada's coal resources is located in areas remote from high demand domestic users and at some significant distances from deepsea ports. This places great demands on the transportation system and has forced the coal and the transportation industries to adopt highly efficient methods of handling the product and hauling it to market position. Most of the coal not consumed in minemouth thermal power stations is carried by rail over lines operated by the two transcontinental railway systems, Canadian National and Canadian Pacific. These rail networks are extensive and have the advantage (as compared to most other North American railways) of being able to handle coal movements from origin through to destination without interchange to other rail carriers. Coal SourcesWith exception of the coal produced in Cape Breton, Nova iScotia, all the significant shipping volumes in Canada emanate ifrom mines located in the three most westerly provinces. Figure I ishows the geographic distribution of the major mining operaitions shipping coal to domestic and export markets. The prinicipal routes and the tonnages carried (1980 calendar year) are ialso indicated. iThe 1980 shipping data are summarized in Table I. Saskatchewan lignite began moving from Bienfait to Thunder Bay by CP Rail unit trains in mid-1981 at the rate of one million tonnes per year. The product is handled through Thunder Bay Terminals and delivered directly to a nearby Ontario Hydro electrical generating station."

Jan 1, 1985

By B. Jin

Removal of fluoride and chloride by alkaline washing from direct lead smelting dust which originated from an Ausmelt furnace is reported. The results show that the fluoride removal efficiency increases with an increase of alkaline concentration, alkaline washing temperature and time. The L/S ratio has little effect on fluoride and chloride removal efficiency. A new flow sheet for removal of fluoride and chloride from the dust was successfully proposed according to the results. Fluoride and chloride removal efficiencies are more than 53.68% and 63.18% respectively using the flow sheet under the optimum parameters of temperature 338 K, L/S ratio 3:1 and alkaline washing time of 1.5 h. The contents of fluoride and chloride in the alkaline washing residues can meet the standard of zinc purity as hydrometallurgical materials for zinc processing.

Jan 1, 2014

By A. P. Craig

"I HAVE BEEN looking forward to addressing this particular audience about Trans-Canada Pipe Lines because you men, more than most, understand the problems of the pioneer. Trans-Canada Pipe Lines qualifies as a pioneer on two counts: it is certainly pioneering a completely new industry in Canada -the long-distance transmission of natural gas -and it has at least a few of the problems that are expected and normal to any pioneering venture.This morning, I’m going to try to give you a sketchy picture of our project and a brief report on its current status and our progress to date; and then a broad picture of Canadian markets for natural gas.The physical characteristics of the Trans-Canada Pipe Lines project have been discussed so often that I am not going to take the time today to quote a lot of statistics on pipe sizes, miles, tons of steel, etc. Suffice it to say that this project, estimated to cost approximately $350,000,000, will be the longest large-diameter gas pipe-line ever built anywhere.Let me try to paint a broad picture of this great national project, using only a few basic 'round' figures.First, it involves exploration for and development of the natural gas fields in Alberta and other provinces -the cost of which will run into hundreds of millions of dollars.Then comes the gathering, stripping, and cleaning of the gas before it can be delivered to Trans-Canada. This will cost close to $100 million.Next we have the Trans-Canada Pipe Lines project for transmission of the gas to Eastern markets -estimated to cost $350,000,000 during the first three to four years and making natural gas economically available to one-half the population of Canada."

Jan 1, 1955

By A. H. Lang

Introduction Tin continues to be as much a strategic metal as it was during the war. This situation is due to the fact that the tin mines in the major producing areas of Malaya and the Netherlands East Indies have not yet reached their pre-war production. Moreover, the world requirements for tin in certain fields, particularly in the food pack industries, are steadily increasing. At present, tin is still under International allocation by the Combined Tin Committee, of which Canada is a member nation. This Committee reviews periodically the availability of refined tin for export from the producing countries and makes allocations of tin to ensure equitable distribution to the consumer countries. In 1947, availability permitted an allocation of only 70 per cent of stated requirements. From 1935 to 1938 the price of tin in New York averaged 49 cents a pound and during the war the price in Canada was controlled under a subsidy programme at levels from 60 to 70 cents per pound. Just recently, this price has been raised to 96 cents. The value of the Canadian production amounts to about half a million dollars annually and the whole of this is obtained as a by-product of the lead-zinc-silver ores of the Sullivan mine in British Columbia. In 1947 Canada's imports of tin were 3,961 long tons valued at over $6,000,000. In addition, tin plate to a value of $8,000,000 was imported from the United States; the tin content of this is estimated to be from 650 to 700 long tons. An increase in domestic production would, therefore, be of great national importance, and the present high price may make the search for and development of tin deposits more attractive than it has been in the past. Although no one can foretell what future prices will be, there is reason to believe that, unless there is a drastic downward revision of production costs, the price will be maintained at present levels for some years. A number of tin occurrences are known in Canada, but none of these have been developed for their tin content alone.

Jan 1, 1948

By A. Ignatieff

"A practical picture of the effects of stress and of the structural environment in an extraction area in a bedded deposit is described, and the main factors of ground control where principles of rock mechanics can be applied are discussed. Reference is made to early work in Europe, where systematic rock mechanics studies started in coal mines, as well as to the early work in the Canadian coal mines.During the past two decades, considerable theoretical and experimental knowledge, pursued both in the laboratory and in the field, has accumulated throughout the world, but the state of the science still does not permit application of substantiated theory such as is found in the design of above-ground structures, largely because of the complexity of the rocks. The mining engineer, as oppm1ed to the civil engineer, is constantly faced by exposures of new ground that is often subject to unpredictable discontinuities. However, the rationale already developed by rock mechanics principles and experimentation provides concepts and information that may be useful in selecting mining layouts. These concepts and existing measuring techniques can also assist ground control as mining progresses.Many of the bedded deposits, much as coals and evaporites, have pronounced deformation properties, and there are limitations in making stress measurements within short distances of mine openings or extraction areas. On the other hand, the measurement of movement of the hanging wall (roof) and footwall (floor) of roadways and extraction faces, as well as the sides of pillars, provides a most useful tool in assessing ground stability.This paper is to be regarded as a brief progress report with particular reference to Canadian applications of rock mechanics to bedded deposits."

Jan 1, 1968

By J. W. Meier, J. O. Edwards, R. C. Bell

"IntroductionTHE DIE CASTING industry .as we know it today is the direct result of the invention and development of die casting machines during the nineteenth century and of reliable alloys in the twentieth. The early machines were designed to cast low melting point metals such as lead .and tin, and their alloys.It was inevitable that, as these die castings were put into service, the demand should arise for stronger materials. Zinc alloys, often containing lead, tin, copper, and aluminum as major constituents, were relatively easy to cast and stronger than the lead and tin alloys. However, it became apparent after a number of years that these zinc alloys tended to become brittle, distort, and corrode, particularly if kept in warm, humid atmospheres. Thus, considerable quantities of zinc-base .alloys were in use before the trouble was realized and effective measures could .be taken to determine the cause of the instability.The deleterious effect of certain metallic impurities on the properties of zinc •die casting .alloys has now been known for about thirty years. Brauer .and Peirce, and, later, other research workers of the New Jersey Zinc Company such as Anderson and Werley, discovered the pronouned effect of lead, cadmium, and tin on the stability of zinc-alloys."

Jan 1, 1952

By G. Swan

"The selection of material comprising a backfill is, of economic necessity, site dependent. Nevertheless, given the existing range of typical components-coarse waste, alluvial sand, tailings a balanced or optimal choice is no straightforward matter. A new design approach toward deciding what constitutes an optimum combination of backfill material promises to be useful. In particular a 'binder ' number, based on the mean distance between aggregate particles, specific surface and cement content, is proposed. Using this number, related empirically to compressive strength, the expected mechanical performance of any cemented fill can be predicted.IntroductionOver the years a considerable volume of information has accumulated on mine backfill material design. The principal aggregate component has been deslimed mill tailings, though more recently admixtures of rock waste, sand and tailings are quite common. For these materials uniaxial compressive strength and percolation rate properties are known to be controlled by, among other things, aggregate grading. While empirical formulae exist for relating grading to percolation rates, considerable uncertainty exists concerning strength development."

Jan 1, 1985

By D. W. McDonald, N. A. Duke, R. L. Hauser

"Abstract- The NERCO Con Mine is situated in the amphibolite facies aureole of the Western Plutonic Complex overprinting the Yellowknife Greenstone Belt. Metamorphic grade of the upright monoclinal basaltic succession decreases from hornblende-amphibolite facies along the border of the batholith to greenschist facies. Metamorphic isograds, subparalleling the faulted margin of the batholith, transect volcanic stratigraphy and coincide with major gold­ bearing shears.Gold mineralization is confined to north-striking, west-dipping shear zones where hanging­ wall amphibolite facies mineral assemblages retrogress to chlorite-carbonate-sericite-sulfide bearing schists hosting multiple generations of quartz-ankerite veins. The gold-producing portions of the Con and Campbell Shears occur where these structures transect an east trending thermal corridor. The corridor is defined by granitic plugs and a number of related breccia bodies, that can be traced outwards from the batholith across the greenstone belt.Prograde reactions of greenstone during amphibolitization effectively liberate fluids that partition metals. With retrograde reactions at shear zones, gold is precipitated with quartz due to the destabilization of sulfide and arsenic complexes. The coupling of regional prograde metamorphic and restricted retrograde metasomatic overprints suggest mineralization is temporally related to emplacement of the Western Plutonic Complex. Economic gold concentrations within the intrusive corridor indicates enhanced metamorphic overprint of hornfelsed greenstones enveloping satellite intru sives peripheral to the main batholith."

Jan 1, 1993

By E. E. Mason

THE Myrtle group of mining claims is situated on Barkerville mountain in the Cariboo mining district of British Columbia, west of the old mining town of Barkerville. An 1,800-foot adit, known as the Shamrock tunnel, was driven in 1935-36 from the Barkerville road and in the general direction of the Myrtle group. It was proposed to enlarge this adit to more convenient section, extend it 2,500 feet int0 Myrtle ground, and from there drive a main entry 3,000 feet along the length of the group. Several laterals were also to be driven off this main entry as part of the tunnel schedule. It was thus originally proposed to drive 5,500 feet of new adit and 1,800 feet of laterals, a total of 7,300 feet of new work. Work was commenced with a bulldozer on April 21st, 1941, cutting a bench on the hillside for a plant site. The power plant was ready for operation on August 8th. Slashing and re-timbering of the old adit rook longer than was expected. It was found that 57 per cent of the length required timbering, chiefly by fore-poling, and there was also trouble in several sections with swelling ground. First round in the new face was taken on September 17th, when a 2-shift daily schedule was commenced. Due to delays in delivery of electrical equipment, it was not possible to add the third shift until November 14th. From then on, a 3-shift daily schedule was maintained with the exception of holidays and fortnightly change Sundays until August 1st, 1942, when shortage of labour caused the dropping of a shift. All work was suspended on August 14th. The ground through which the tunnel passed was such that the driving was often interrupted by the need of protective timber at the face. Further, crews were continuously employed timbering behind the face, and in maintenance of timbered sections in swelling ground. Roughly 980 feet of the new workings are now timbered, about 21 per cent of the total.

Jan 1, 1942

By K. J. Heale, G. G. Richards, D. J. Rioux, R. L. Stephens

Slag fuming has remained a key process for the recovery of Zn, Pb, and minor elements in the integrated flow sheet at Teck Cominco's Trail Operations for more than 75 years. Since the start-up of the KIVCETTM process and the #3 slag fuming furnace in 1997, a range of process intensification projects have been completed to improve metals recoveries and throughput based on improved process control, mechanical modifications, and, most recently, the implementation of oxygen enrichment of the blast air. This latter project, initially named 'nitrogen depletion' and now 'nitrogen oxygen performance enhancement' (NOPE), is the primary focus of this paper. NOPE reduces the amount of heat required to heat the inert nitrogen gas, and therefore more of the energy input can be used for reduction. It also frees up boiler capacity because the inert nitrogen gas does not then have to be cooled down. A dynamic METSIMTM model was developed to determine the opportunities to improve the process capacity and heat balance to both assist with justifying the project and to verify the observed furnace behaviour. Several process safety management issues were also addressed and a few key minor mechanical modifications were made to allow the project to proceed to commercial implementation at 25% blast air oxygen enrichment. Short term plant trials have confirmed the model predictions. The first three months of a long term, continuous trial showed a 6% increase in zinc fuming rate from average furnace performance despite the implementation of a KIVCETTM fluxing change to assist with minor element recovery that was expected to negatively impact the zinc fuming rate by 3 to 5%. This encouraging result is also in line with the model predictions.

Jan 1, 2008

By F. P. Agterberg

"IntroductionTHE KNOWLEDGE about the mineral resources in a region ranges from relatively precise ore-reserve estimates for known deposits to probabilistic estimates concerning the speculative resources which may be discovered in future at greater depths and in the less-explored parts of the region. Previously developed probabilistic methods for regional resource evaluation (1) are based on the following two assumptions.(1) The probability that a specific block of rock, or part of a region close to the topographic surface, contains undiscovered deposits can be estimate d by weighting selected geological, geophysical or geochemical parameters for that block. The weights are computed by considering similar environments which are known to contain deposits.(2) Some of the characteristics of the undiscovered deposits, such as ore tonnages and average grades of metals contained in the ore, can be evaluated by considering probability distributions f or known deposit data. These methods were initially applied to Precambrian deposits in the Abitibi Volcanic Belt of the Canadian Shield (1).Since 1972, statistical methods for quantitative resource evaluation have been applied to the occurrences of the mainly Paleozoic base metal deposits in t he Canadian Appalachian Region. The objectives of this project (Project Appalachia) have been discussed by Leech (2) in a paper that introduces 8 papers with results of the exploratory data analysis. Project Appalachia represents an effort to develop and apply methods of combining information and concepts from regional geology, metallogeny and geomathematics for computer- aided regional mineral resource evaluation."

Jan 1, 1977

By W. E. Davies

"This paper is the sequel to that on Developments in Sintering Efficiency delivered by Davies and Mitchell at the International Ore Dressing Congress, Stockholm, 1957. Attention is drawn to the fundamental concept of sintering as a heat transfer process, in which the ignition heat is continually transferred onward through the bed as a heat wave. By its passage, this heat initiates endothermic 'changes, such as carbonate decomposition, whose energy requirements are supplied by the combustion of the fuel contained in the bed.Ideally, the heat wave should be generated by the ignition hood followed by the pre-heating of the incoming air. The fuel content of the bed should be no more than the theoretical quantity needed to balance the endothermic changes. In practice, the heat wave is seriously short of energy and this is offset by excess fuel in the bed. As a result, sinter quality suffers, more return .fines are produced, and fuel is wasted, a loss of efficiency which could be avoided if the fundamentals of correct ignition were more widely appreciated.Sintering speed, otherwise heat wave velocity, is a function of the rate at which the incoming air acquires .heat from the cooling sinter and imparts it to the unburned feed below the combustion zone. It is thus a function of rate of air flow and so depends on bed permeability>. Ways of• improving and maintaining permeability at the maximum consistent with thorough sintering are discussed, particular reference being made to taconite concentrates. The possibilities of recrystallizing refractory ores into forms more amenable to physical concentration techniques by sintering are visualised, very little expenditure on heat energy being required when the process is operated near the ideal conditions."

Jan 1, 1960