Search Documents

By Coates J. R, Firth I. C

The Imperial Smelting Furnace at Cockle Creek, NSW, was constructed in 1961 and is the oldest facility using the Imperial Smelting process in operation. In recent years there have been significant improvements in many areas of the operation, including production, safety, hygiene and environmental performance. Steps taken to achieve these improvements are described. Plans to secure a profitable future while meeting environmental requirements are outlined.

Jan 1, 1993

The geologic settings, geochemistry of host rocks, mineralogy and metal values in modern back-arc volcanic-hosted massive sulphide (VHMS) mineralisation are very similar to those in many ancient polymetallic VHMS deposits. The geology, distribution and styles of seafloor mineralisation in modem back-arc basins, especially the eastern Manus and Lau Basins, southwest Pacific, are compared to VHMS deposits in the Mount Read and Mount Windsor districts of Australia . Based on exploration and research in modem back-arc settings, geologists are now observing the direct analogues of the polymetallic VHMS deposits currently being exploited in ancient back-arc volcanic belts throughout Australia and the world.

Jan 1, 1995

By Guvenir HA

This paper summarises a cost optimisation procedure by minimising the total drill metres and the overbreak that occurs in tunnel excavation in medium strength rock (uniaxial compressive strength

Jan 1, 1995

Modern mining and coal cleaning techniques lead to the generation of large quantities of fines which give rise to problems in their storage, handling, transportation and further processing. Pelletisation, a method of particle agglomeration, can alleviate such problems. This paper provides a brief overview of the principles of pelletisation and a survey of the coal pelletisation literature. Then it reports results from an experimental investigation of the effect of surface active reagents on coal pelletisation. Finally the paper is concluded with a few remarks on applying the results from the experimental study to practical coal agglomeration.

Jan 1, 2000

The city of Kalgoorlie-Boulder is located 595 kilometres east of Perth in Western Australia, and has a population of just over 30 000. Western Australia's third largest city lies on one of the richest goldfields in the world, with over 45 million ounce

Jan 1, 1998

With production at Olympic Dam scheduled to commence in June 1988, it has been necessary to install a complete underground ore handling system capable of removing two million tonnes of material annually from the mine. The system comprises mucking from stope drawpoints, truck haulage to underground storage, primary crushing, conveying and hoisting. On the surface, material is conveyed to stockpiles at the Metallurgical Plant. Mining of the numerous special excavations within the system was incorporated into the mine's ongoing development program prior to the underground construction phase. Utilisation of a decline from the surface enabled versatile construction equipment to operate at the underground sites as well as simplifying the transportation and delivery of construction Materials.

Jan 1, 1988

Esso Australia Ltd. operates a large natural gas producing system in the Gippsland Basin, supplying gas to the Gas and Fuel Corporation of Victoria, the State Electricity Commission of Victoria and several industrial customers. Gas reaches the Longford processing plants from three offshore platforms via a network of large diameter pipelines, which must be protected against the formation of ice-like hydrates. When gas production commenced in 1969, methanol was used to inhibit hydrate formation in the offshore pipelines. However, later investigations showed that the methanol was causing excessive degradation of molecular sieve in the onshore gas-processing plants. (Molecular sieve is used to remove water and H2S from the gas prior to further processing to remove heavy hydrocarbons.)

Jan 1, 1982

The epizonal Ag-Pb-Zn vein deposit at San Bartolome is characterised by a base-metal sulphide assemblage containing the spectacular development of interpenetrating, bladed networks of pyrrhotite which have been replaced by marcasite and pyrite. A similar assemblage displaying the same crystal habits and textures are also a diagnostic feature of the Sn and Sn- Ag deposits of Bolivia. On this basis, it is reasonable to conclude that both deposits were formed from fluids of similar nature and origin. Although no economic accumulation of Sn is known in San Bartolomr, further comparison of the geologic setting, age, mineralogy, fluid inclusion data and magmatic association of this deposit with the Bolivian systems has highlighted additional similarities consistent with a hypothesis that more extensive Sn mineralisation might exist in the San Bartolomd area.

Jan 1, 1995

Interaction between rock and fluid plays a critical role in rock engineering ventures such as stimulation of oil and gas wells, geothermal energy recovery and nuclear waste isolation. Robust and reliable design of the related services and underground facilities is based on understanding of the mechanics and chemistry of the coupled hydromechanical- thermochemical processes. This paper explores the application of the theory of such processes in minerals engineering, with particular reference to rockburst mitigation, in situ solution mining and cavity completion of coal-bed methane production wells.

Jan 1, 1995

Spatial data processing using geographic information systems produces qualitative results which are superior to those from other existing software tools. However, the answers to various quantitative questions in mining operations is often limited by the capacity of the GIS to process appropriate spatial data. The efficient operation of a large underground mine demands that an adequate GIS be put in place.

Jan 1, 1995

By Thomson S, Eisenstein Z

Field instrumentation was installed to monitor ground and lining behaviour during and after construction of the Mount Shaughnessy Tunnel (Rogers Pass Short Tunnel) in Canada. The instrumentation was placed in a soft ground section of the tunnel at its crossing with the Trans Canada Highway. The tunnel was excavated through a dense bouldery soil. Presentation of the field data and inter- pretation of the tunnel performance from a geological-geotechnical point of view form the basis of this paper. The loss of ground due to the tunnel excavation was found to be exceptionally small. This has been attributed to the unusually high strength and stiffness of the host soil. Evaluation using the Boundary Element Method, together with a simplified analytical technique, were applied to assess the relevant soil parameters and their influence on the tunnel performance.

Jan 1, 1987

By Artone E

screening equipment installed in e Hamersley Iron operation is described, and tails of operating parameters and screening - Iia in use are given. Tests were carried out on full-size reens in the operating plants to study the Meets of mat aperture size, feed size distri 1,ution, feed rate, screen speed and throw, angle of inclination, and feed moisture content n screen performance. Sampling equipment was signed so that undersize samples could be htained from various locations along the length of the screen, thus providing information pout the quantity and size of particles passing òhro gh the screen at any point. Conclusions derived from the testwork and relevance of these to the Hamersley Iron aeration are discussed.

Jan 1, 1984

By Ito H, Noguchi F, Ueda Y

DTA curves of synthesis lead sulfide and commercial. lead concentrates during oxidation were measured to clarify the mechanism of ox- idation of lead sulfide. The oxidation reac tions could be divided to elementary reactions with production of basic lead sulfates such as 2PbO PbSO4. An existance of iron sulfide played an important role of the oxidation of lead concentrates. The oxidation rates of lead sulfide were measured in the wide range of oxygen potenti- als using IR type SO2 gas-meter. The oxidation rates under low Po 2 which corresponds to the direct oxidation smelting were much lower than those obtained under high Pot. The combustion temperatures of lead sulfide were also measured by hot thermocouple method. Those values were extremly low compar- ing the oxidation temperatures obtained by DTA.

Jan 1, 1987

Present knowledge of the Pacific floor in- dicates: Postulated subduction zones and/or moving basements overlain by undisturbed sediments. Contiguous mantle convections of conflict ing directions and variable rates. Disharmony between transform faults and mantle convections. =hese features are shown to be difficult to reconcile with conventional hypotheses of sea f 1mr spreading and cast the model into serious doubt.

Jan 1, 1987

By McNay L. M

Two field studies to monitor fill pres sures and vein-wall deformation were conducted in mines of the Coeur d'Alene mining district in Idaho. Both operations employed cut-and-fill mining techniques in nearly vertical veins aver- aging 10 feet in width, and backfilled with classified mill tailings. Hydraulic pressure cells were used to measure transverse, longitudinal, and vertical pressures within the backfilled stopes. Rock bolts extending into the manways and mechanical closure devices were used to monitor vein-wall convergence. Continuous recorders were used with selected pressure cells to prolong the life of the installation. Transverse pressures in excess of 600 psi and stope wall closure up to 22 inches were re- corded. Closure rates were higher at midheight of the stope than they were near either sill, indicating that the vein walls react similarly to a beam supported on each end.

Jan 1, 1973

By Cocker A, Kavetsky A

A numerical model describing blast fragmentation and damage in three dimensions has been developed at the Julius Kruuschnitt Mineral Research Centre (JKMRC) and applied to numerous blasting operations in mines throughout Australia. The model combines the rock structure (summarised by block size distribution) with blast strain energy and uses comminution theory to calculate the resultant block size distribution. The model distinguishes between rock breakage and failure, the former being defined as size reduction and the latter as block dissassembly. The background and basis of the model are discussed in detail and three case studies presented describing the application of the model to explosive performance evaluation, explosive selection and drill selection in Australian mining operations.

Jan 1, 1990

By Ishijima Y, Goto T

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic ar- ray. Location of microseismic events and in- tensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the inten- sity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increas- ing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are con- sidered. Observed and predicted displacement of the shaft axis agreed well.

Jan 1, 1992

Faced with rising costs and lower metal prices, several Ontario base metal sulphide mines have changed their method of mining to vertical crater retreat mining. This is a bulk mining method that utilises large diameter holes and mines successive cuts remotely by blasting and cratering the bottom of the drill holes. The orebody is mined from the bottom up. The method in turn has required a change in materials handling to cope with the greatly increased productivity.   This paper presents an overview of vertical crater retreat mining in the Sudbury area using examples from several producing mines. The paper reviews the history of vertical crater retreat mining, various methods of applying vertical crater retreat layouts, the development of in-the-hole drills capable of drilling the large diameter holes required, methods of explosives loading and blasting to achieve the required cratering effect, methods of ground support including backfill placement, and the ore loading equipment presently being utilised including remote control load-haul-dump units and continuous loaders.   The safety aspect of vertical crater retreat mining has been of concern, and was the focus of a provincial inquiry. The benefits in improved safety are demonstrated through an analysis of various records kept by the mines and provincial agencies.   Future trends can now be envisaged, particularly in relation to deep mining. Some experimental work which could have practical applications, is described.

Jan 1, 1989

The Mount Lyell Company's concentrating mill is situated about a quarter of a mile westward of the portal of the North Lyell tunnel, which serves the North Lyell, Royal Tharsis and Crown Lyell mines, being on the 1100-ft. level of the first named. The Comstock mine is connected with the tram system at this level by five and a half miles of steam tramway, two-foot gauge being standard throughout.The plant is well placed with regard to all essential services and has an excellent water-supply from a series of three dams on the West Queen river.MILLING ORESThe mill feed is a mixture of the outputs from the foUr mines mentioned, each of which has its characteristic ore, but, generally speaking, about half of the ore consists of siliceous schists and the other half of hard grey quartzite. The schisty ores are easy to crush, but, on grinding, while the schist slimes readily, the quartz granules are hard, resulting in the handling of heavy loads on the secondary classifiers. The quartzite ores are both hard to crush and difficultto grind.The principal sulphide materials are bornite, chalcopyrite, and pyrite, chalcopyrite being the main copper-bearing mineral.The crystallization is coarse in the schisty ores, but it has been shown that even the 200 mesh (Tyler) material contains included sulphide particles. At the present time the sizing of the final tailing averages 80% through 200 mesh.

Jan 1, 1932

By A Hewitt

Portland cement is the chief binding ingredient in mine backfill. In the presence of water, the chemical compounds within portland cement hydrate causing hardening and strength gain. During hydration, heat is generated. In certain cases, hydration heat may be produced significantly faster than it can be dissipated, which can create high temperatures in the underground environment. This paper presents the results of a series of investigations aimed at quantifying the heat generated by cemented backfill during hydration. Scaled stope models, instrumented with thermistors, were used in the investigation. Heat transfer to the hanging wall, orebody, footwall and cross-cut and production drifts was assessed during the backfill curing process and relationships between cement content, cure time, and heat generation were developed. The results of this work will assist mine operators in predicting the heat generated by cemented backfill and provide the necessary information to implement effective engineering control of heat in the underground environment.

Jan 1, 2005