Search Documents

By Swanson AR, Nicol SK

A study has been made into the influence of feed size distribution on the flotation response of coal. The results show that a full description of the flotation response of a coal must not only consider the inherent floatability of the coal, but also, the size distribution of the feed to flotation. The performances of a number of flotation circuits were compared using a coal which was "poorly floating" because of its size distribution. Split feed flotation, two stage reagent addition, and reflotation of classified tailings all gave better yields than that obtained by conventional single stage flotation. The optimum flotation circuit for the washing of the coal in question, was reflotation of classified tailings.

Jan 1, 1978

By Dai Q

The mechanism of flotation of potash ores with long chain primary amines has been assessed. Since at high electrolyte concentration in saturated brine the electrical double layers of the interacting particles and bubbles are entirely compressed, the induction time measurements confirmed the elimination of kinetic factors associated with the energy barriers opposing particle-to-bubble attachment under such conditions as could be expected. The lack of the kinetic hindrance resulted in the correlation found between the contact angles on the KCl surfaces and the sylvite flotation measured under the same physico-chemical conditions. The iep values and acid numbers obtained for various Esso oils tested as extenders in the flotation of coarse potash ore fractions confirmed the base oils with high content of nitrogen-bearing compounds to be good extender oils. The performance of such oils could further be improved by dissolving in them a small amount of long-chain aliphatic amine.

Jan 1, 1993

By Harrison J

The correct selection of equipment to use in a mine is a problem which constantly faces the mining engineer. In some cases a wide choice of equipment with different operating characteristics is available. If this equipment is to be used to assist in moving the ore it may be possible to build a computer simulation model to predict how it will perform. Typical problems that lend themselves to this type of analysis are presented. The computer models are constructed using a recent form of the GPSS computer language, namely GPSS/PC for the personal computer. This language allows the programmer to construct models in a very short time and at a low cost. Of great importance is the easy way in which it is possible to change the models to answer any of the "what if?" questions the engineer may pose.

Jan 1, 1987

By Moffatt G

Approval to operate Longwall No. 7 at Appin Colliery in 1979 was granted pursuant not only to the usual statutory provisions, but also that an adequate means of drainage of methane gas be incorporated. A methane drainage plant was subsequently designed and constructed some two km from the pit top at the site of the Colliery main upcast and down cast shafts. Modern plants of this nature are completely automated using programmable controllers and computers to provide control and management reporting functions. Complex mechanical systems are installed to extract the gas and in handling and storage processes. Gas utilisation plants exist which can generate power from methane. These plants are further enhanced by harnessing waste heat produced in the generation process. The installation, automation control and monitoring of these plants incorporates many facets of engineering from high voltage power supply and computer technology to complex gas handling procedures used in gas compression storage.and generation of electric power.

Jan 1, 1982

By M Warren

The professional geologist or engineer on a mining operation has a particular view of their operation. This is based on the factors of the operation that have a direct impact on the daily work program of the professional, such as production rates and grades. The view that would be taken by a financier who is called upon to support the project may be somewhat different. The value of the operation to the financier is in its ability to generate surplus cash for its owners and thus repay the debts to the financiers, with as low risks profile as possible. A number of tools are used to test the sensitivity of the project to variations in the key cost/revenue drivers. The Financier may call on a team of technical specialists to assist with the assessment of the cash flow and risk profile and to monitor the development of the project. The ability to offset this risk, as all projects have some degree of risk, may be a key factor in determining the level of financial support to be offered.

Jan 1, 2002

Jan 1, 2004

By OÆGrady P

Finite element analysis is becoming a routine component of design of longwall extractions, now superseding more traditional somewhat intuitive approaches. Finite element modelling is relatively inexpensive and provides an adequate degree of similitude to give satisfactory analysis. The physical modelling of two decades ago is now largely replaced by numerical methods of which finite element is the best known. Important data for finite element work are physical properties, including creep aspects, introducing the non-linearity of stress response.Various computer packages are available and some were used to model two specific UK examples, using both linear and non-linear approaches. It appears that non-linear approaches will yield most benefit. The use of materially non-linear analysis is merited by the greater similitude it provides between model output and real mine situations.

Jan 1, 1991

Longhole stope overbreak has always been a source of unwanted cost within the underground mining industry, and efforts to control it using various rock reinforcement systems have long been a rock engineering challenge. At the Pasminco Mining Broken Hill Operations trials have been carried out using an innovative cable bolt reinforcement system known as Rib-Roc. The system, based loosely on the Swedish Rib-in-Roc concept, utilises zones or ribs of heavily reinforced rock in the troublesome hangingwall and back areas of longhole stoping. The trials were carried out under a strict qualitative and quantitative scientific stope measurement program utilising rock mechanics instrumentation. Not only did the trial demonstrate the success of the system but data obtained was useful in implementing the system virtually as standard practice throughout the operation.

Jan 1, 1995

By Coin CDA

From a study of coke samples obtained from the tuyere level of four Australian Blast Furnaces, the nature of in-furnace coke degradation has been investigated. At the periphery of the raceway is a concentration of fines and the lump coke appears dull and rounded. However coke from the deadman is angular and relatively undegraded. Cokes made from higher rank coal appear to suffer preferential attack of the reactive maceral derived component (binder). The coke from lower rank coal appears to be attacked non-preferentially by the solution-loss reaction. Initial attempts to simulate these phenomena have given results consistent with these findings. From chemical analysis of the tuyere probe samples there appears to be a relative increase in carbon and decrease in-.sulphur and phosphorous between stockline and tuyere level. An overall decrease in coke mineral matter derived material was noted and associated with this was a significant gasification of silicon. Consequent formation of silicon carbide was noted.

Jan 1, 1981

The Engineering Chemistry Division of the Government Chemical Laboratories of WA initiated an ongoing investigation into the possible utilisation of diatomites of this State. The work has shown that local diatomites can be beneficiated by hydro or pneumatic cyc- lone separator circuitry and that the better quality head materials can be upgraded by straight and flux calcination and associated processing to the equivalent of premium grade imported products. Western Australian diatomites vary con- siderably in quality, and the degree to which they can be upgraded and the yield of useful product are influenced by the proportion of impurities and the size, type, and degree of fragmentation of contained diatoms. Conseq- uently careful assessment of ore deposits will be necessary in order to relate ore reserves to planned production. The viability of commercial production from Western Australian resources would hinge on the establishment of markets - largely ex- port - capable of supporting a production level of the order of 30,000 tonnes per annum.

Jan 1, 1979

Optimum selection of explosives by means of monitoring explosive performance can lead to increased profitability through the control of fragmentation, a reduction in hangingwall and footwall damage and overall drill and blast costs. Studies conducted at the Mount Lyell Mining and Railway Company underground copper mine evaluated in situ the performance of four explosive types. Measurements included monitoring the levels of induced shock energy and the attenuation thereof with distance. The velocity of detonation (VOD) of these explosives was also measured using in-hole techniques. Assessment of these results, together with a knowledge of the rock mass strength, facilitated the selection of an explosive that was best suited to the given rock mass conditions.

Jan 1, 1995

By Miyatani J. Asaki Z, Kondo Y

The oxidation of sphalerite particles of 60 to 100 mesh size was studied in a fluidized bed of low 02 concentration at 900¦C. Par- tial pressure of 02 in the fluidizing 02-N2 gas mixture was chosen between 0.0009 and 0.02 atm. In the region of p02 between 0.008 and 0.02 atm, the oxidation rate was lowered with the decrease of p02, and the unreacted-core model was applied. At lower pbelow 0.008 atm, the reaction rate was enhanced as compared with the calcu- lated values from the unreacted-core model. From microscopic examination, it was found that ZnS was evaporated at the particle surface and the dissociated Zn vapor was oxidized in the gas phase. Initial reaction rate and the distance between the surface of inner sphaler- ite core and the oxide shell were studied based on the model of enhanced oxidation.

Jan 1, 1980

By Alford R. A

The causes of the loss of heavy mineral from mineral sands wet concentrators were identified through detailed surveys of two such concentrators. It was found that tray and spiral sluices preferentially lost elongated panicles, but panicle size had little effect on loss. Recovery was shown to increase with panicle density. The major influences on the recovery efficiency of individual concentrating devices (stans) were feed rate and feed grade, recovery increasing with decreased feed rate and with increased grade. Uneven distribution of total solids and heavy mineral to individual stans contributed to losses through the corresponding effects in feed tonnage and grade. Computer simulation demonstrated that significant recovery improvements could be obtained by appropriate adjustment of splitters to optimise the characteristics of internal plant flows.

Jan 1, 1991

The paper deals with the taking of soundings in connection with coal mining operations under part of the Pacific Ocean adjoining John Darling Colliery.INTRODUCTIONIn the early days of mining in the Newcastle District there did not appear to be any definite law specifying the limits to which mine workings, other than certain borings, could extend under tidal waters.As time went on, a figure of 120 ft. was fixed as the minimum thickness of strata between the roof of the seam and the sea bottom; beyond this mining operations are disallowed. The laws relating to working coal under tidal waters are as follow:-The minimum width of pillars to be left shall be eight (8) yards and the maximum width of bords or other excavations shall be six (6) yards, but the lessee may at his discretion increase the minimum width of the pillars or decrease the maximum width of the bordsor other excavations so as to increase the general safety.The eight (8) yard pillars shall be left unwrought.In on-road of every pair of Winning-off or leading headings, a bore shall be kept going ten (10) feet in advance for the purpose of foretelling the presence of any fissure, wash-out, open joint, fault, dyke, or otherwise, and all winning-off headings shall be driven atleast one hundred (100) yards in advance of the working bords.The most accurate and trustworthy information shall be obtained by the lessee not only' of the depth and character of the ocean bed, river, lake, or estuary deposit, but also of the strata overlying the coal seam.When working under the ocean, strata shall be bored through and proved a minimum thickness of thirty (30) feet at the face of the leading headings or levels immediately such headings or levels are under the ocean, and...

Jan 1, 1947

By F R. A Jorgensen, G W. Jensen

A pilot scale experimental investigation of the condensation of zinc vapour from smelter off-gases was performed in conjunction with a mathematical modelling study of the system. The work investigated the feasibility of using the high heat and mass transfer rates associated with a fluidised bed to condense zinc directly from smelter off-gases containing zinc vapour. Of particular interest was whether zinc would revert to zinc oxide during the process of condensation, and whether a zinc fog would form and be carried out of the condenser. A 0.1 m diameter fluidised bed condenser was mounted on the top of a 200 kVA DC electric arc furnace in which mixtures of vapours and gases were generated at 1150 - 1300¦C. The gas/vapour mixtures investigated included Zn/N2, Zn/N2/CO/CO2 and Zn/N2/H2/H2O. Greater than 90 per cent of the zinc was deposited on the zircon sand bed of the condenser, and there was no sign of zinc oxide formation, suggesting that the rate of heat transfer was faster than the reaction rate for zinc oxide formation. There was also no evidence that fog was being formed in the condenser. Using the methods of Kunii and Levenspeil (1991), a mathematical model was developed to predict the behaviour of the fluidised bed condenser. The model enabled the distribution of gas/vapour temperature and bed temperature to be determined as a function of distance from the condenser inlet. Similarly the partial pressure of zinc vapour in the gas mixture, and hence the mass transfer rate of zinc to the particles, was determined. Experimental data allowed validation of the predicted bed and gas/vapour temperatures.

Jan 1, 2000

Particles finer than 10 um often cause problems in flotation. The current under- standing of the nature of the following effects is discussed: slime coatings on particles, carrier flotation, increased froth stability, entrainment of ultrafine gangue, excess reagent consumption, slower rate of flotation, more reactive surfaces. The review emphasizes the principles underlying these effects rather than details of progress in practical solutions to the problems they cause. The princi- ples of selective flocculation and floc flotation and the various approaches to achieving selectivity are discussed. Hydrodynamic effects on floc growth are reviewed. The evidence suggests that satisfactory performance in the ultrafines fraction will be achieved only by simul- taneously increasing the rate of flotation of the ultrafine valuable mineral and de- creasing the rate of entrainment of ultra- fine gangue.

Jan 1, 1984

The problems arising in the excavation of hard rocks with the use of mechanical tools consist chiefly in a slow advance rate accompanied by an intensive wear due to the toughness and abrasiveness of the rock. In order to allow the further extension of mechanical excavation beyond the limits of the presently available technology, the assistance of waterjet aiming at improving the performance of the equipment while reducing the wear rate of the tools, has been recognised as one of the most interesting technical solutions. The paper illustrates the improvement of the performance of both disk cutters and picks obtained with the waterjet assistance at the Waterjet Laboratory of the University of Cagliari on a medium-hard rock.

Dec 6, 2010

The gossan developed from the Whim Creek Cu-Zn-Pb-Ag sulphide deposit, in the Pilbara region of Western Australia, occurs near the top of a ridge in a dissected plateau 01 moderate relief. The gossan is characterized by the abundance of secondary ore minerals which indicates that it is relatively immature, due to climatic conditions and erosional stripping.The abundant presence of secondary carbonates indicates that the low pH generally resulting from sulphide oxidation has been neutralized, probably by the buffering effect of carbonatcs and silicates. Fe, Cu, Pb, 'Ag and Sn have been enriched in the gossan relative to the primary ore, and Mn, Ti, Co and Ni have been strongly depleted; other elements have remained substantially unchanged. The gossan has a strong gcochemical signature characterized by high Cu, Zn, Pb, As, Sb, Sn, Ag and Mo coutents. Boxwork textures are poorly developed, bu't the gossan has other diagnostic mineralogical features including sulphide inclusions in quartz and the presence of residual cassiterite.

Jan 1, 1982

British Coal has made a practical progressive approach to improving the reliability of its mining equipment. Reliability must be addressed at the specification stage but does not end there and routine procedures are used to procure equipment of adequate reliability. The techniques used to monitor and improve reliability during the operational phase of the equipment, providing engineers and operators with detailed printouts, together with the types of maintenance employed, ensure high levels of availability. Finally, the methods of repair and overhaul of British Coal equipment and systems ensure that the initial reliability targets outlined on the specification, can still be achieved.

Jan 1, 1991

By D Ziaja, W Jaspers

A brief history of the development of pneumatic flotation cells from early in the 20th century to the present day and a comparison to conventional cells demonstrates the efficiency and simplicity of design and operation of the ænew generationÆ of pneumatic cells. Recent successful testwork on phosphate minerals in the USA and a variety of coal types in Australia confirm the utility and efficiency of the design. The key aspects of this technology are improved recovery and selectivity with lower capital expenditure and operating costs.

Jan 1, 2005