Search Documents

By J Plinke

The imperative to operate sustainably requires all equipment and processes to operate at their maximum possible efficiency. Achieving this ideal state requires a thorough understanding, not only of the process itself, but also of the tools available to design and assess potential improvements. This paper presents a case where the widely employed Discrete Element Method (DEM) toolset proved insufficient to model problematic material flow during the process of optimising wet screening performance. A Smoothed Particle Hydrodynamics (SPH) model was found to more accurately replicate the flow characteristics of the physical system. Site observations identified biased loading of the screen decks to cause inefficiencies in the wet screening of an iron ore processing circuit. Two numerical modelling approaches were pursued with the aim to select the most suitable one and continue the optimisation process based on that selected model. Selection criteria were established, based on the minimum requirements of being able to replicate the problem, including the main flow dynamics deemed to cause the issue. The DEM model was found to over-simplify the slurry flow dynamics within the scrubber and no laterally biased flow was introduced by the scrubber’s rotation to the otherwise symmetric system. Since DEM was not able to accurately replicate the existing problem, it was deemed an unsuitable method to assess the effect of any changes to the system. The second approach consisted of a SPH model. This model was deemed to map the flow within the scrubber with sufficient accuracy to address the problem, as it produced biased screen loading comparable to that reported from site. Changes to the wet chute, delivering material from the scrubber to the screen, aimed to neutralise the non-centrality introduced via the scrubber, were then successfully designed and assessed using the SPH model.

Nov 8, 2021

By E Taylor, F Lebbing

The $2.5 billion EastLink project is a 39 km tollway and includes twin three-lane, 1.5 km long, undrained driven tunnels with cross passages every 120 m. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and help preserve the unique flora and fauna in the area. The design of the permanent concrete lining and waterproofing system for the EastLink tunnels was both innovative and practical, to meet the demanding environmental and production constraints of AustraliaÆs largest road project. This paper describes several key aspects of the tunnel design and construction, including: design of fully tanked, permanent concrete tunnel linings for the main tunnels and cross passages to withstand 37 m head of water pressure in combination with potential rock loading in the future;optimisation of the tunnel shape to minimise the amount of reinforcement required and the design of special welded mesh which was developed within manufacturing constraints;100 year design life and durability considerations in every aspect and detail of the design including concrete mix design and stray current mitigation;development of a precast invert solution for the main tunnel permanent concrete lining to enable faster lining construction and to minimise risks to the tunnel membrane associated with fixing reinforcement and construction traffic;development of prefabricated reinforcement details for the junctions between the main tunnels and the cross passages to enable faster construction and minimise risks to the membrane associated with fixing reinforcement; andincorporating the tunnel drainage sump at the lowest cross passage in the alignment, resulting in deep excavation to satisfy the required storage volumes for drainage.

Jan 1, 2008

By Kavetsy A

In surface mining operations, the ease with which a muckpile may be dug is a dominant factor in mining efficiency. Within broad limits this is largely independent of the fragment size dis- tribution, since the equipment used to move the broken rock is generally larger than in underground mines. In such cases, muck- pile shape and voids ratio within a muckpile heavily influence mine productivity. In a particular operation, the muckpile shape after blasting should be tailored to the digging equipment being used. A front- end loader is best suited to a low, flat-lying, loose muckpile, because of its fairly good mobility and small break-out force with its bucket. In contrast, a rope shovel lacks mobility, generates a much larger break-out force with its bucket, and fills its bucket in a vertical filling motion. Therefore, it is ideally suited to well fragmented, steep faces. In situations where a dragline is used, the requirement for a suitable muckpile depends on the operat- ing scheme of the dragline. For a conventional highwall key method the preferred work- ing level of the dragline is the same as the highwall, so that the dragline may sit over its key. In this situation, the ideal muck- pile shape involves relatively little displacement of the fragmented rock, with a minimal "power trough" at the back of the blast. In throw blasting, on the other hand, it is desirable to cast as much of the spoil as possible across the pit. It is then necessary to optimize the blast design by maximizing the throw percentage under any necessary constraints (e.g. damage, vibration, flyrock, explosive cost).

Jan 1, 1988

The methodology (i.e. procedures) used in testwork for modifying, improving, selecting, designing or developing processes is reviewed and possible improvements described. Minerals and particles could be characterised more comprehensively with modifications of existing procedures. Identification of the dominant phenomenon in a process could help bring the results of laboratory tests closer to plant performance. Improvements in pilot plant testwork could reduce the frequency and magnitude of problems in materials handling and separation in production processes, and increase the quantity and quality of the data obtained from a limited number of tests. Longer-term improvements in methodology depend on some changes in basic research. Information is required about all of the phenomena that occur in a production process rather than sophisticated models of specific phenomena. Theories, correlations and computer simulations could be used more effectively in testwork if they were simple, capable of forecasting the effects of changes and applicable to a number of similar processes.

Jan 1, 1986

By A D. Ferreira, A E. C, A D. Padovezi

The increasing market requirements regarding the quality of products, the enhanced predictability from detailed mine planning, the need for process consolidation and upgrading require continuous investigation on the characteristics of different ore types to be concentrated. This paper addresses the mineralogical and technological characterisation of several itabirite iron ore types and the influence of the composition and mineralogical associations on desliming and flotation. Pellet feed quality and the influence on the major performance indicators, such as weight recovery of slimes, selectivity index, metallurgical recovery, flotation kinetics of iron minerals and gangue is also emphasised. The investigation resulted in a classification of iron ores according to their mineralogical composition, morphology of the crystals, and/or texture and microstructure of mineral particles with respect to desliming and flotation performances.

Jan 1, 2005

A novel solvent extraction process, called the SOHNEX process, has been developed at the University of Utah. In this process, the organic and the aqueous phases flow countercurrently in a horizontal vessel, and the emulsion between the two liquid phases is generated by high-velocity gas jets injected at the bottom. The gas jets are located at certain intervals along the bottom of the vessel with phase disengagement zones on either side of the plume zone created by the gas jet. The system is simple, having no mechanical moving parts or complex internal structures, and yet provides good contact between the phases with minimal backmixing. Tests have shown that emulsions with a wide range of specific interfacial area, including that typically encountered in mixer-settlers, can be generated in this process. It has significant built-in flexibility of operation including the control of the flowrate and hold-up of each liquid phase. The SOHNEX process overcomes the difficulties in the operation of conventional solvent extraction equipment such as mixer-settlers and column extractors. A major advantage of the SOHNEX process is that the energy of mixing can be closely controlled by adjusting the strength of the gas jet. This allows an optimal control of the drop-size distribution of the dispersed phase and thus the specific interfacial area. The process is continuous, and any number of extraction and separation stages may be built into a single vessel. The gas can be recirculated in a closed loop, thus eliminating solvent loss and mist problems, especially for high-temperature operations. The SOHNEX problem can handle solutions that contain suspended solids and that form third phases. The simplicity of the equipment and operation with low maintenance will mean much reduced capital and operating costs as well as low environmental risks and improved safety. The SOHNEX process has been tested for continuous copper extraction from a dilute solution. Calculations also showed that uranium and other radioactive elements can readily be extracted in a small unit of the SOHNEX extractor while satisfying the nuclear criticality condition.

Jan 1, 2000

May I first of all say that I am fully conscious of the great compliment paid to me when I was invited to accept the Presidential Chair for this current year. I realise that it is an onerous task by reason of the fact that the Chair has been occupied in the past by so many able and distinguished men, and I realise also that I have been set a standard which is hard to emulate. "It is my desire however, in accepting the post that I may be able to contribute in some small measure to the further advancement Of the aims and objectives of the Institute and I thank you all for the confidence you have shown in me.Secondly, on behalf of the Company and in my Presidential capacity, I want to extend to each and everyone of you a hearty welcome to Whyalla and I hope that you will all return to your respective fields of endeavour feeling that you have had a most interesting, enjoyabIe and instructive time with us here in Whyalla.In this year of 1951 marking as it does the culmination of the first 50 years of Federation in Australia and yet another half century of human endeavour and progress, we are brought to a point where it is perhaps natural that we should pause, to review what has been achieved, in that span of time, and to look at the tasks ahead.It is no exaggeration to say that the story of Australian development since the inauguration of the Commonwealth 50 years ago has no more remarkable chapter than that of the-growth of its manufacturing industries.Each decade has borne witness to steady and substantial growth of our secondary industries and whilst it is true that our financial well-being still rests heavily on our primary production, we have, as a nation, moved surely in the direction of a more balanced economy. More and...

Jan 1, 1951

By B Hall

The authors have undertaken many independent mine optimisation and operational improvement projects at Australian and international mining operations over the past decade. This work has provided an understanding of the underlying practices responsible for the good long-term performance of some operations, and the failure of others to achieve their objectives. Good long-term performance, and value creation can be achieved through a logical and rigorous process of identifying the optimal mine plan (æThe PlanÆ) that delivers the corporate goals, establishing appropriate performance measures that are aligned with these goals, and ongoing monitoring of compliance with the established targets to ensure the operation reliably achieves The Plan. A number of practical methods have been developed and implemented to assist mining operations deliver their corporate goals. This paper outlines some of these methods, providing some fundamental guidelines that will assist in the establishment, and reliable achievement of The Plan that delivers the corporate goals.

Jan 1, 2006

By Moyes A. J

The Intec Copper Process uses a strong chloride electrolyte at atmospheric pressure and 80 - 85¦C to produce high purity, 99.99 per cent copper granules and elemental sulphur. A recent, exhaustive study by an independent, major Australian corporation has shown the capital cost of an Inter plant to be approximately half that of a copper smelter at the 200 000 tpa capacity level and approximately half the operating and capital cost at the 50 000 tpa level. The Inter process costs were also shown to be greatly superior to the best available leach/SX/electrowin technology. The process utilises a multi-stage counter current leach at 80 - 85¦C with the addition of air at atmospheric pressure to precipitate iron as a goethite type compound, followed by a two-stage purification process separating impurities in metallic- and other forms. Purified cuprous chloride/sodium chloride solution is fed to an electrolytic diaphragm cell where high purity copper granules are produced at current densities of 1000 - 1500 A/m2 withoutthe need for conventional electrode stripping. Power consumption is approximately half that of the cupric route. The product is suitable for the direct powder metallurgical conversion of the granules to products such as wire or strip. All the steps in the 'furnace free' conversion of copper mineral to product have been demonstrated The process can treat low grade and contaminated concentrates without penalty, thereby offering greater returns to the miner. Lead, zinc and silver may be recovered as metals, with the high oxidation potential of the electrolyte allowing extraction of gold at high efficiency. The gold is selectively precipitated on activated carbon with negligible copper and silver contamination.

Jan 1, 1992

During 1991 - 1993 the author interviewed approximately thirty senior managers of varying responsibilities in either the engineering, construction or operation of a heavy industrial facility. The purpose of the exercise was to determine the factors driving a deterioration of the working relationship between the engineering and the operating company following practical completion of a major project. From the research a number of conclusions have been drawn as to the root cause of the deteriorating relationship. For this paper we are drawing on this initial research and our ongoing experience of solving problems of this nature to present some fundamentals that can be used to break the breakdown maintenance cycle.

Jan 1, 1998

By Palmer DJ, Bain JH, Pullen JB

Over the last ten years at Risdon, zinc production capacity has almost doubled. This has resulted in modifications, many of which have affected zinc deposition operating conditions in the cells. Some of these changes appeared to have affected average current efficiency to such an extent that a special investigation was initiated, using multiple regression analysis to assess historic cell unit operating para- meters. The study highlighted the importance of certain parameters in maintaining maximum current efficiency for zinc deposition from !Risdon purified solutions under conditions of !changing current density, acidity and zinc con- centrations. Maximum current efficiency was obtained only within a zinc to acid ratio in cell electrolyte of 0.45 - 0.55 and a residual zinc concentration greater than 48 g.1-1, irrespective of actual zinc concentration or The investigation also established: ieters giving minimum power consumption at termined current density; the effect of ntration changes in common impurities on nt efficiency; the existence of high s of some impurities in solids precipit- in the cells and pure solution tanks.

Jan 1, 1975

This paper examines the interplay between longwall support design/geometry features, operational controls and geological features on ground response. Experience from several investigations is used to demonstrate the influence of factors such as longwall support capacity and geometry, setting pressure, coal seam strength and stiffness, tip-to-face distance and hydraulic supply and control system parameters on longwall ground response. These factors are then used to outline the requirements on key controls such as retreat rate and cutting height and their influence on allowable roof convergence. The ground response curve concept as a means to provide graphical representation of longwall support and strata interaction processes is presented. The approach was developed to address the requirement for a practical longwall support evaluation and selection tool that can take account of support load influences such as changes in roof geology or cover depth. An example of the comparison between single pass longwall and top coal caving in a thick seam environment is given to demonstrate the influence of the various factors discussed.

Jan 1, 2005

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

With some notable exceptions, marine placers located just below, or just above, present sea level, are responsible for much of today's production of detrital ilmenite, rutile, zircon, and other minerals of value. The purpose of this paper is to discuss the paleogeographic and paleo-oceanographic factors which may have determined the location of presently submerged marine placers. These factors-include changes in sea level, burial by recent marine sediments, stream capture and other i changes in drainage patterns, and recent changes in climate. Selected geologic situations in the Yellow Sea off the coast of Korea, in the Atlantic Ocean off the coast of Portugal, in the Bering Sea off the coast of Alaska, and in the Arabian Sea off the coast of India, will be used to illustrate the author's point of view.

Jan 1, 1980

By Henderson J

Iron ore samples selected from the Deepdale, Iron Prince and Mt. Newman ore bodies have been pelletised on a pilot scale plant and subsequently reduced under laboratory conditions by hydrogen or carbon monoxide. Pellets approximately 1 cm in diameter have been reduced by hydrogen over the temperature range 5000- 900¦C and the results examined by thermogravimetric, microscopic, electron probe and x-ray techniques. After an initial time delay it was found that up to 95% reduction the rate of reduction could be described by a transport con- trolled porous model, in which the effective diffusivities of hydrogen in theòpr¦duct layer and the reaction zone are filar. Independent measurements of effective diffusivity supported the values obtained from the reduction data. ve 95% reduction the rate decreased markedly due to the formation_of retained wustite or fayalite. Comparison with reduction by carbon monoxide over the temperature range 7500 - 900¦C showed that the rate eduction by carbon monoxide was approximately five times slower than the rate by hydrogen. The rate of reduction was found to be a function of the properties of the pellets, which may account for the ely conflicting results that have been obtained in previous investigation on porous pellets.

Jan 1, 1970

The necessity for agreed project outcomes, which are in accordance with client needs, and the subsequent requirement for a unique approach to managing project implementation is discussed. Reasons for appointing a separate project team to manage a project are established. The selection of a project manager, based on the services they can provide and on their characteristics, skills and management style, is discussed. The consequences of selecting the wrong project manager are explored. A broad overview of the requirements for the project team is provided. Criteria for the selection of team members, and the role played by the project manager in this selection, are discussed. The levers that drive `on-time and on-budget' projects are discussed in terms of the project's vision, goals, controls, and incentives.

Jan 1, 1997

Dilution in underground coal operations can be underestimated by up to five times during feasibility studies, with disastrous economic consequences. Every one per cent of stone waste introduced can reduce an in situ specific energy of 25 MJ/kg by some 0.25 MJ/kg and increases the abrasiveness of the run-of-mine coal. Where a wash plant is not in place, penalties imposed for not meeting contractual specifications alone can amount to some $A 1 million per year. This paper presents a method for monitoring, reporting and ultimately controlling dilution in an underground coal mining operation and presents the dilution trends from a continuous miner/longwall mine over an eight year period. The overall dilution level for the mine can be back-calculated by comparing the run-of-mine coal quality to the predicted in situ, undiluted quality. However, this will not identify the actual contaminant types, areas of the mine responsible for the dilution and the reasons for the dilution. This additional information is essential for controlling dilution to acceptable levels. Quality and horizon control using existing sampling information is generally only adequate for longer-term control purposes, and is not suitable for monitoring mining-induced dilution. The cost of close-spaced surface drilling to collect the information necessary for short-term control is prohibitive, particularly for deeper mines. However, much of this data can be collected through underground channel sampling and horizon control measurements taken during continuous miner development and longwall extraction. The mine runs the risk of not meeting contractual quality specifications and of increased equipment wear if this additional information is not available and the sources of dilution cannot be controlled. The information can also be used to plan longwall extraction heights on a short-term scale with resulting improvements in productivity.

Jan 1, 2003

This paper comprises a discussion of standards for comparing conditions in mines, of methods for measuring the flow of air, of a comparison of fan performances, and the application of these matters to mines in Western Australia.UNDERGROUND CONDITIONSIn approaching the question of mine ventilation one naturally searches for some standard by which to measure the conditions in a mine.There are several clauses in the Mines Regulation Act defining the conditions which are permitted. The quantity of CO2 is limited to 0·25 by volume, but the estimation of CO2 involves a chemical determination and is not suited for general use in a mine.The maximum temperature is fixed at 87 0 F. (dry bulb), and at 80° (wet bulb). The reading of temperature is easily done in the working places, and this is a very valuable and practical test of the conditions in a mine.The wet bulb temperature is probably the most important factor in determining working conditions. It is obvious that human life cannot be sustained for any appreciable period if the wet bulb temperature is above blood heat (about 97°F.). In places where the wet bulb temperature is 90°F. there is danger of heat stroke.In places where the air in a mine is still, the wet bulb temperature rises to a value close to the rock temperature.Adequate ventilation cools the workings by transference of heat from the rock to the air stream, and the temperature...

Jan 1, 1939

Mine planning studies of iron ore deposits are often based on resource models generated by ordinary kriging. Ordinary kriging aims for local accuracy to minimise the variance of expected estimation error but this is at the expense of reproducing variability of the original sampling data. Hence mine planning studies using kriged models are likely to underestimate product variability, and the required blending and stockpiling capacity to reduce variability to an acceptable level. Instead, conditional simulation models of the main chemical variables in iron ore are able to reproduce likely variability to be encountered during mining and processing. This approach is demonstrated in a case study of the Weld Range bedded iron ore deposit in Western Australia, with a comparison of ordinary kriging and conditional simulation models. Conditional simulation models suggest that, compared with the single ordinary kriging estimation, there is likely to be far greater block variability for iron and impurities, a greater requirement for stockpiling and blending capacity, highest variability in initial years of mining and less variability in later years of mining for deeper ore. The conditional simulations provide a more realistic range of mining outcomes for production of high-grade ore, which may be seven per cent less than in the kriged model, as well as for lower expected project net present value (NPV). In year one, the kriged model is conservative for NPV; however, in later years two to five the kriged model has higher NPV than most conditional simulations, suggesting expected NPV based on the kriged model may not be achieved. For improved decision-making in mine planning, a complete range of possible outcomes from conditional simulations of the deposit should be considered rather than relying on a single kriging estimation that may be an end member case in the range of possible mining outcomes.

Jan 1, 2009

By S Johnston, L Howe, S Stevens

Regulators have an important role to play in fostering and enabling reliable, effective, environmental management. Given this, it is perhaps surprising that there has been relatively little debate on exactly how regulators can enhance their own approaches, in order to promote improved outcomes overall. The authors argue that applying research on High Reliability Organisations, as well as the University of Pennsylvania’s Penn Program Framework for Regulatory Excellence, to regulators has the potential to facilitate positive environmental results across the mine life cycle.

Aug 2, 2023