Search Documents

By Corbett GJ

Epithermal gold-silver deposits occur in young volcanic terrains where post-mineral cover commonly impedes the search for mineralisation. At the Togi Project in Honshu, Japan, a complex mineralised system is largely covered by post mineral volcaniclastics. A combination of high resolution electrical resistivity surveying and detailed airphoto interpretation has, with close geological control, enabled synthesis of structural and alteration characteristics of the Togi geothermal system, in turn permitting ranking of the prospects for drill testing.

Jan 1, 1990

The continuously growing coal mining industry of India presently includes shovel dumper combinations in open cast mines, sometimes with dragline mining of overburden, together with the whole range of longwall and bord and pillar underground mining, continuously undergoing fuller mechanisation. This transition from "low tech" to "high tech" systems is now monitored for reliability and provides bases for comparisons of downtime relative to age and make of equipment, whether imported or indigenous, including spare parts, as well as frequencies of particular failures to allow analysis and progressive improvement. Varying geologies complicate technology and equipment requirements, especially in underground mine,s with minimal technological standardisation, but now, reliability in South Eastern Coalfields Limited has been given more importance and superior technological back-up is being developed.

Jan 1, 1991

By Walker V

The 'MAGNADET' to provide a safe enhanced protection extraneous currents, electricity and radiodetonator was designed electric detonator with against the effects of current leakage, static frequency energy.It has found a particular niche in shaft sinking operations and Mount Isa Mines initiated trials of the system in 1983 as part of the design work for the 3000/3500 orebody access shaft.Initial surface blasts indicated a number of significant advantages which were confirmed during the bench and concrete phase of the M37 shaft sink. The application of 'MAGNADETS' was later extended to the horadiam phase of the project.Details of the exploder capacity calculations for the various M37 round designs are included with the paper.

Jan 1, 1985

By Sheridan GD

Fifteen samples 'of clays and shales from the Adelaide area were selected from a total of 84 as representing material of possible value for the manufacture of light-weight aggregate. A detailed examination of the bloating. characteristics of these revealed four likely to be suitable. for expansion.' in a rotary kiln. One of these, a Tapley. Hill shale., was-fired in an 8 in. diameter rotary kiln, but con-tinuous bloating without ring formation in the kiln was not achieved. Steam,,-oxygen,, sulphur dioxide and carbon dioxide have been, suggested. as the agents of bloating. An examina-tion of .. the evidence : `leads to the conclusion that carbon dioxide derived from. carbonate minerals is likely to be the principal bloating agent. Attempts to bloat clays by the addition of mica were.not successful.

Jan 1, 1963

Reverse circulation (R.C.) drilling or the dual tube method as it is quite commonly known, has a unique place in conventional mineral drilling. It can be classified half-way between open hole drilling at the lower end of the scale and diamond drilling at the upper end. The system basically consists of two tubes, one inside the other, with compressed air flowing between the inner and outer tubes. Sample cuttings return up the inner tube through the head of the rig and via a hose to a cyclone where the sample is collected. This system means that the cuttings are free of contamination as they are at no time in contact with the outside formation of the hole.Reverse circulation drilling is divided into two areas: R.C. Roller and Blade for softer formations; and R.C. Percussion for harder formations.

Jan 1, 1986

By Linkson PB

The presence of residual cyanide in mine tailings and fill sands may, under specific circumstances, lead to acute and/or chronic cyanide poisoning of the environment and individuals. In this paper, the nature of cyanide contained in mine tailings is discussed, along with the circumstances under which such cyanide would become a hazard. A number of methods for cyanide degradation are reviewed in the paper, with special emphasis being placed on biological degradation (due to its low costs and the non toxic nature of the degradation process itself). Recommendations are made as to the best methods of setting up a biological degradation system, for use in mining Situations.

Jan 1, 1987

By Mortensen JK, Lang JR

The Canadian Cordillera contains numerous classic porphyry deposits and several unusual subtypes, including the alkaline suite of porphyry Cu-Au deposits and the Tombstone magmatic suite and associated Au¦W deposits. The alkaline suite formed in collisional settings in island arcs whereas the Tombstone suite was emplaced in an active fold and thrust belt in a continental arc. In addtion to different regional settings, these suites differ in the type of underlying basement, metallogeny, and the styles of mineralization. Both magmatic suites were emplaced over short intervals, probably in response to specific tectonic events. In the case of the alkaline suite, the tectonic event promoted magmatic processes suitable for the formation of porphyry Cu-Au deposits. The tectonic environment is less well constrained for the Tombstone suite, but the result was the formation of distinctive porphyry and intrusion-related Au¦W deposits.

Jan 1, 1995

During conventional eddy current separation, a repulsive force is applied to metallic particles by placing them in a rapidly changing magnetic field generated by a spinning magnetic rotor carrying an arrangement of alternate magnetic poles. This method works effectively for larger non-ferrous metallic objects, such as aluminium cans, but as the metallic particles become smaller, the bulk repulsive force on the particles is increasingly replaced by a rotational torque. Therefore, for small metallic particles it makes sense to use particle rotation, rather than particle repulsion, to effect a separation. Eddy current separators using particle rotation are similar in construction to present separators, but are designed to produce a rotating field of essentially constant angular velocity and field strength. Practical and economic particle rotation eddy current separations are possible down to particle sizes of about 200 ¦m, but separations, at probably uneconomic rates, can be carried out on particles as small as 50 ¦m.

Jan 1, 2000

By P Scott

Kaltim Prima Coal, an open cut coal mine located in Sangatta, East Kalimantan, Indonesia, operates two deep pits and two shallow pits with a truck and shovel operation. KPC produced 17 Mt of coal in 2002 by removing 120 Mbcm overburden. Geochemical investigations have indicated 20 per cent of total waste rock is potentially acid forming; ie it has the potential to create acid mine drainage (AMD). In the early years of the KPC operation, the presence of AMD had been observed in the mined out areas and in the waste rock dumps as a result of sulfidic waste rock exposure. A strategy for management of AMD from waste rock was implemented involving: sampling, analysis, modelling, selective handling and validation of final dump covers. Samples of the waste rock lithologies are collected from exploration drill holes for geochemical analysis to determine their acid generating potential. The geochemical database is used to develop the waste rock model for the life of mine pit areas. The acid forming and non-acid forming waste rock is delineated for each mining bench area for selective handling and placement within the waste rock dump during the operational stage. Each mining bench is sampled and assessed to validate the model predictions. The final dump cover is sampled to meet strict Quality Assurance requirements to ensure non-acid forming waste material is used in the outer cover of the dump. The geochemical investigation of the waste rock is integrated with mine planning to design and construct the waste rock dump to minimise the risk of generating acid. This process links the exploration stage, operation stage, and rehabilitation stage for each Pit area. The paper briefly reports the waste rock characterisation, waste modelling and strategies used for management of acid drainage by KPC.

Jan 1, 2003

The scope, pace and depth of mining is creating a need for improved ground control strategies to meet mine safety standards. Ground control and associated conservation problems relating to subsidence and the disposal of mining and metallurgical wastes can be resolved by mine filling with selected reject materials. The lack of suitable criteria to evaluate the applicability of such materials and especially cemented forms of fill is considered. Sulphide wastes, which are prone to oxidize, and cement are inexpensive mine fills, but their incorrect use can give rise to problems which are briefly described. Research work concerned with the utilization of sulphide wastes such as mill tailings, to produce fill with self-cementing properties has shown that the development of cohesion and strength is attributable to natural oxidation processes controlled by the physical and chemical composition of the fill mass. The cementing is caused by a number of oxidation products, and is most effective when the mineral pyrrhotite is present. The concepts of fill design are outlined and various criteria for assessing durability and deformational properties are proposed. Specimens prepared in the laboratory are capable of attaining unconfined compressive strengths up to 28 MN/m2.

Jan 1, 1973

Geomechanics is one of the more specialised aspects of site supervision on a major tunnell- ing project. The controlled deformation of a rock mass as a result of tunnelling and the knowledge of loading of temporary and permanent underground supports are important for safe, economic construction. These basic parameters depend on the construction method and sequence and the geological conditions through which a tunnel is driven. Thus geomechanical monitoring during the construction phase provides feedback to a design team and allows any revisions to a design to cater for local conditions not revealed by earlier investigations. Detailed geological mapping is an integral part of geomechanics in the construction phase. It serves as a monitor on pre construction predictions and also forms part of the as- constructed record. If conventional excavation-techniques are adopted, geomechanics can provide a service of blast' vibration monitoring of surface structures in urban areas.

Jan 1, 1976

The able address on the currency question given by the Right Honorable A. J. Balfour, M.P., late leader of the Government, at the Mansion House lately, before a large and influential audience, will strike a key-note that will resound throughout the world. It is high time that gentlemen of position and influence should come forward and express their views on this subject, so as to cause the matter to be,more seriously considered than it has been. The question can be no longer ignored or treated with indifference by bankers, financiers, merchants, miners, and others interested in the settlment on some basis the relative values gold and silver bear to each other. It is gratifying to not that such a great leader of political opinion as Mr. Balfour has given serious attention to this important question.The address created a deep impression ,on the minds of many who probably had not given the matter much att.ention, and Mr. Balfour's words will re-echo over a wide range of thought with such effect that I have no doubt they will materially help to check the downward tendency of the value and uses of silver. As a mining engineer, interested in the development of our mining resources for increasing gold aud silver for currency, and having devoted much attention to the subject, I cordially approve of the views set forth by Mr. Balfouf, and I think the general body of all interested in the production of gold and silver will do the same.

By F Cesnik, P Griffin, S Green

In July 2004 a flotation concentrate regrind circuit was commissioned in the æHigh GradeÆ Ridgeway concentrator at NewcrestÆs Cadia Valley Operations. This was the culmination of two years of project testing, process design and planning which commenced shortly after commissioning the concentrator in March 2002. During the two-year project evolution alternative grinding technologies were evaluated from conventional ball milling through to sand milling. A Detritor mill was eventually selected for the duty and the criteria on which this selection was based will be presented. As the project evolved so too did the equipment sizing with the concentrator quickly exceeding design capacity of 4 Mtpa and currently averaging 5.6 Mtpa, the process design had to accommodate this and future potential throughput increases. This paper will focus on the supporting testwork, circuit surveys and concentrate properties which were used as the design basis for the project. The economic evaluation which led to the project receiving board approval in November 2003 will also be presented. Detailed design and construction management issues will be discussed as will preliminary results and findings up to November 2004.

Jan 1, 2005

The purpose of this paper is to outline the equipment used for diamond drilling at Mount Isa, together with alterations and recent improvements therein. As the majority of the drilling is carried out with machines running at relatively high speeds using XRN blast hole bits, the paper is mainly devoted to this branch of drilling.Because diamond bit costs constitute the major expense, a considerable amount of research into bit design has been carried out, and in several instances, costs per foot have shown an appreciable decrease in spite of rising manufacturing costs and higher diamond prices. Equipment performance has at times been erratic due to delays in delivery and occasionally because of faulty parts, but in general the position has improved by keeping in close contact with the manufacturers.BLASTHOLE DRILLING MACHINESThe standard blasthole diamond drill is the 'E-500' two cylinder air powered model manufactured by Mineral Drillers Limited. Several of the older pattern JV41 are still in use, but are being retired as they wear out.. Machines are repaired in the underground diamond drill shop.The normal feed gears used when drilling in lead shales are 350 top gear and 450 low gear-actually 357 and 438 revolutions per inch of advance respectively. The 300 gear was commonly used several years ago, but it was found that bit footages could be increased without any appreciable drop in penetration rate by reducing to the 350 gear. Gears used for copper drilling are 650 and 750. Footage per shift...

Jan 1, 1953

By Wickham P

Digital computer based control systems are used to implement control and monitoring over most unit operations in Mount Isa Mines Limited lead-zinc concentrator and copper concentrator. Implementation has been gradually devel- oped and expanded since the first process computer installation in 1969. Operations currently using high level control logic include crushing, grinding, on-stream analysis of flotation products, flotation reagent additions, and tailings thickening. Details of gains in metallurgical efficiency for each system are considered.

Jan 1, 1978

By J S. Moema, R Paton, J Zimba

Today, most organisations are familiar with the pressure to increase their effectiveness and efficiency, regardless of the nature of their business. Cost cutting and increased productivity are the main themes of many initiatives to ensure the profitability of operations and, ultimately, shareholder satisfaction. It is well known that the cost of comminution to liberate minerals such as gold from their respective ores is a major expense for mines. Comminution costs consist predominantly of grinding balls and electricity. However, there are no national or international standard specifications for grinding balls û on which a single mine may spend several million dollars per month. In addition, in the past mines generally did not specify the minimum requirements when purchasing grinding balls from suppliers. The result is that every supplier has its own grinding ball recipe (regarding chemistry and heat treatment), and is under no pressure to implement a quality assurance plan to ensure that a consistent product is delivered. The resulting variation in the quality of grinding balls leads to increased steel consumption rates and hence increased milling costs. A more stringent quality plan will generally not be welcomed by suppliers since this may entail further investments and/or reduce the production rate. In a sense, suppliers benefit from poor quality grinding balls as this leads to increased sales. Perhaps the main problem is a lack of understanding of the factors that influence grinding ball performance. This paper will describe the factors that influence the wear rate of grinding balls from both a microstructural perspective and a mill perspective. In addition, some insights are provided on the different grinding balls available and ways that users can verify their quality.

Jan 1, 2007

By R Uken G P Whitmore

The coastal dune cordon of northern KwaZulu-Natal is amongst the highest in the world reaching heights in excess of 180 m and up to 2 km in width. It comprises a complex system of Quaternary stacked dunes of various geomorphologies, types and ages. The dunes contain economic heavy minerals which are currently exploited ~20 km north of Richards Bay. Although mining of these ore sands has been in operation for the last two decades, little work has been undertken on the clay-fraction (

Jan 1, 2001

Builders have been very familiar with iron since ancient times, but because of its weathering characteristics it was relegated to use as a fastening material in unexposed places and bronze became the popular metal for exposed applications. It is of interest that iron nails buried deeply about A.D. 87 at a Roman fortress and carefully covered with clean beaten earth under conditions practically excluding oxygen were found to be almost unrusted 1870 years later. (1) Today, weathering steels, which contain less than 2% of alloying additions, can be used in exposed situations without protection and without experiencing continuous wastage. As we all know the steady access of atmospheric oxygen to the surface of plain steel causes continuous corrosion. Weathering steels, on the other hand, due to their alloying additions develop their own impervious surface layer which limits the access of atmospheric oxygen and effectively limits corrosion. Table 1 shows the chemical composition of a plain carbon steel and a typical weathering steel. Fig. 1 shows what we refer to as direct corrosion - time curves in which corrosion loss is plotted against time of exposure in an strial environment. The weathering steel has a high rate initially which then decreases steadily for about three years, as the stable rust film builds up. This is followed by a practically linear relation where the very low corrosion rate, according to one school (2), is due to a blocking of the rust pores by insoluble complex salts formed from interaction of the oxidation products of the separate alloying elements. The start of the linear region represents a total corrosion loss of only about 2 thousandths of an inch.

Jan 1, 1970

In recent years a large amount of work has been done at various plants overseas, and also at Broken Hill Associated Smelters, Port Pirie, South Australia, on the use of Dwight Lloyd sintering plant gases for sulphuric acid manufacture by the contact process.Several plants have modified their sintering machines and operating procedure, and some have adopted gas recirculation techniques, to obtain a relatively high proportion of the sintering plant gas at an S02 concentration acceptable to a contact acid plant 1.These adaptations were investigated at Port Pirie, and it was found that gases of suitable S02 concentration could be obtained. The results justified installation of a contact acid plant and a decision was accordingly made in 1949 to construct such a plant.However, the local conditions presented some difficulties not generally encountered at other plants, the chief differences being:a. For maintenance of production of 98% H2S04 , an unusually high S02 concentration is required, because of the prevailing high temperature 'of the purification train cooling water.b. The entire sintering operation is conducted on two large machines, 55ft. x 10ft., operating in series as "First" and "Second over" machines (a two-pass roast.) Any interruption" to either machine causes a complete interruption of plant operation and gas flow.

Jan 1, 1951

The design of water and ore addition points has an important bearing on the ease of operation of a grinding circuit. The nature of some of the design decisions and the possible options of the designer are discussed. For example, design decisions determine the ease of alteration and measurement of flowrate, the ease of maintenance, and the effectiveness of feed- back control loops which maintain material inputs (water and ore) at required values. To illustrate discussion in the paper, a grinding circuit which contains one rod mill and one ball mill in series is used. Practical ramifications of desigl decisions :;ne stressed.

Jan 1, 1978