Search Documents

Expansion of the B.H.P. Co. Ltd. mater ials handling facilities, at their Newcastle Steelworks, began in 1964 and continued until 1970. The present complex handles the annual iron ore requirement of some three million tons for the Sinter Plant and Blast Furnaces. Iron ore is discharged from ore carriers and conveyed at rates up to 3,000 t.p.h. to either of two 180,000 ton capacity storage yards, where it is blended using boom stackers. Material is reclaimed from these yards at rates up to 1,000 t.p.h. using a slewing boom bucket-wheel reclaimer and fed to a screening station. Oversize material is scalped out and crushed in a closed circuit cone crusher. Undersize material is sized on double-deck vibratory screens which separate at 1/4in (6mm). The two fractions are blended in two of four 70,000 ton capacity blending yards using slewing boom travelling stackers. Bridge-mounted bucket-wheel reclaimers reclaim the blended piles at 1,000 t.p.h. Fine ore is conveyed to the Sinter Plant and lump ore to a second screening station, for rescreening, before passing to the Blast Furnace.

Jan 1, 1972

By G Varley

This paper describes the mining methods and strategy used to extract the 5 Orebody crown pillar at the Isa Lead Mine over the past five years. The bulk of the crown pillar was extracted by the use of sublevel open stope method. An uphole bench stope was mined to scavenge the remaining ore. Geomechanical issues associated with the crown pillar extraction are described. Stope sizes were gradually increased on a stope by stope basis. This has allowed the maximising of ore recovery while relevant risks were managed. The principles in designing ore rib pillars against various types of fill materials are also described.

Jan 1, 2002

By Mercer J. K

Shaft guide reaetions in No. 2 Ore Shaft, Mount Isa Mines Limited, have been reduced to a low order of magnitude by the use of self aligning slippers and spring loaded guide rollers. Before commissioning the new 4500 h.p. winder at No. 2 Ore Shaft in January, 1958, it was realised that the increase in hoisting speed from 1800 to 2650 ft/min. would cause high shaft guide reactions which would be increased further when the elongated 12 ton skips replaced the existing 7 ton skips.The Cambridge accelerometer was used to measure the shaft guide reactions and to confirm that progressive skip modifications were resulting in reduced reactions. The skip modifications were completed in 4 weeks.INTRODUCTIONIn 1956 an expansion programme was initiated to increase production from 5000 to 11000 tons per mining day. At No. 2 Ore Shaft the 1500 h.p. winder operated at 1800 ft./min. and hoisted a 7 ton capacity skip. The new 4500 h.p. winder operates at 2650 ft./min. and hoists a 12 ton capacity skip. No. 2 Ore shaft is equipped with two 5 ft. by 5 ft. hoisting compartments (Fig. 1) and any increase in skip capacity meant an abnormally long skip. This feature, coupled with the increase in hoisting speed, could have caused very high shaft guide reactions. Before commissioning the 4500 h.p. winder, a Cambridge accelerometer was borrowed from the University of Adelaide and was used to measure the shaft guide reactions. Rather than carry out an extensive shaft timbering programme, the skips were modified by fitting cushioned guide shoes and spring loaded guide rollers (Fig. 1). Testing commenced in February, 1958, and was completed in March, 1958.

Jan 1, 1961

By T R. Justice

The Eastern Distributor tunnel is located approximately 24 m beneath the suburbs of Woolloomooloo and Darlinghurst to the east of the central business district of Sydney. The 1.7 km long tunnel will carry three lanes of northbound traffic over three lanes of southbound traffic in a æpiggybackÆ arrangement, with a maximum cross-section 22 m wide by 12 m high.The tunnel is constructed predominantly within horizontally bedded Hawkesbury Sandstone. In the unweathered to slightly weathered state, the rock is typically medium strength (average UCS about 24 MPa), with an average quartz content of 72 per cent.Major geological features that intercept the tunnel route are the Woolloomooloo Fault Zone and two extremely to moderately weathered dolerite dykes. The fault zone intersects the tunnel at about 25¦ to its alignment and comprises a series of discrete faults over a width of approximately 50 m. The overall movement of the fault zone appears to be reverse. The two dykes are the 1 m wide Oxford St Dyke and the 6 m wide Great Sydney Dyke.This paper outlines the site investigations and the interpreted geotechnical model for the tunnel route prior to the commencement of tunnelling. This model is then compared to the encountered conditions. The very good correlation between the expected and the encountered conditions shows the high quality of geotechnical investigation and interpretation.

Jan 1, 1999

Teleoperation is one method by which an operator can remotely control and monitor a vehicle. The operator monitors the status and progress of the remote vehicle by watching the video transmitted from one or more cameras which are mounted on the vehicle. In the case of an LHD, it will be fitted with three cameras. For a twin-boom Jumbo, four cameras are mounted on the drill, three of which will have remote pan, tilt, 15x zoom, focus and lens cleaning controls. The advantage of teleoperation is that an operator can stand in the drive and send the remote vehicle around a corner, completely out of sight and still clearly see what is happening. This means that an LHD returns with a full bucket and a Jumbo can be operated from a safe distance. Standing in the drive teleoperating vehicles, exposes the operator to passing traffic including the remote vehicle. There are two solutions to this problem. One is to equip the operator with a Nautilus æBuddyÆ jacket which will help to protect them from all vehicles. The other is to move the operator into a safe room or area, away from the fumes, the noise and the traffic. In this comfortable, less stressful environment, the operator will be more productive and less likely to accidentally damage the vehicle. The operatorÆs æsafeÆ room does not have to be a formal control room, it can be any area which has AC or DC power available and is large enough to contain a chair and a 1.5 m x 0.75 m table. The æsafeÆ room can be on the surface or underground, it does not matter to the operation of the Nautilus Equipment. If the LHDÆs, trucks, locomotives, etc are automatically guided from origin to destination, the operator is free to operate several vehicles at a time, performing only those tasks which are too difficult for a computer to do by itself.

Jan 1, 1998

Estimation of operating costs in the nickel production industry requires a detailed analysis of material flows from mine to smelter to refinery. Despite the small number of nickel producers compared to other base metals, the existence of two very different ore types (sulphide and laterite) and a wide variety of mining and processing technologies make the identification of these flows of critical importance if an accurate global picture is to be obtained. Smelting and refining processes in nickel metallurgy have evolved with a high degree of adaptation to specific operating conditions in different locations. Overall costs are calculated by combining individual cost elements for each unit in production chains from mine to saleable metal product. The average cost of western world primary nickel production in 1995 was US$2.07/lb ($4560/tonne). Average operating costs remained virtually unchanged in the three years to 1995 after an 8.5 per cent fall in 1993, but a 3.9 per cent increase to $2.15/lb is expected for 1996. A major factor in this rise results from the lower prices of copper and cobalt this year, reducing the by-product credits available to major producers.

Jan 1, 1996

Transport Canada (Federal Government) constructed the Halifax International Airport (HIA) near Halifax, Nova Scotia, Canada in the late-1950s. Site location criteria were primarily; direct access to the city and a raised flat topography. Unfortunately, the site chosen was located on shallow Meguma group pyritic slate bedrock. In 1982, during the construction of an airport taxiway, it became very apparent that acidic run-off from excavated bedrock at the site was having a negative impact on adjacent aquatic habitat. The ensuing 20 years involved many efforts to rectify the acidic drainage problem with mixed results. Some of the techniques which have been implemented at HIA to address the acid rock drainage (ARD) issue include: dry covers, wet covers, wetlands, electrochemical treatment, open limestone channels, limestone gravel polishing beds, agricultural limestone application, and two hydrated lime [Ca(OH)2] addition treatment plants, the first producing low density sludge and the new one that creates high-density sludge. Based on over 20 years of water quality monitoring data it is apparent that only certain acid drainage mitigation methods have been effective at HIA. In 2000 when the Halifax International Airport Authority (the Authority) took control of the operation and management of the airport, including the ARD issue, it was decided to construct a modern, highdensity sludge, hydrated lime treatment system. This new $CAN 7 million system is now in operation and is achieving compliance with water quality guidelines. Due to high operating cost, a review of methods to optimise the system is being carried out. The HIA ARD problem, though minor by comparison to most mine sites, has provided unique challenges and may provide valuable insights into this urgent environmental and financial issue.

Jan 1, 2003

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

By I R. F MacCulloch, K Jones

Pintail Systems, Inc, a Colorado USA based company has developed and commercially applied bioremediation processes for biological detoxification of cyanide compounds in mine waste. Site-specific microorganisms are isolated from spent ore, tailings or process solutions and augmented in the laboratory for cyanide oxidation, denitrification and metal biomineralisation. Biological processes typically treat complex contaminants (cyanide compounds, soluble metals and nitrates) in a fraction of the time of conventional remediation processes. Cyanide is used in microbial metabolic processes as a carbon or a nitrogen source. Biological detoxification processes applied at the end of mine life can end long-term liability and perpetual monitoring and containment. Case studies from commercial application and demonstration programs for the US Environmental Protection Agency will be presented in this paper.

Jan 1, 2004

Oaky Creek Coal (OCC) has embarked on an ambitious program to fast track the introduction of Trench Mining into its current mining operations. The project has the capacity to allow the extraction of reserves at stripping ratios, uneconomical by conventional mining methods.Trench mining using Continuous Highwall Mining (CHM) technology reduces the in-situ stripping ratio to 4:3; compared with a stripping ratio of 20:1 using conventional mining techniques.

Jan 1, 1992

In this paper presented are the criteria used when assessing the harmfulness of shocks affecting the buildings. Those criteria are based on the value of speed or accelerations of building vibrations. Presented is the scale of harmfulness of vibrations of Langefors and Kihlstrom, Bureau of Mines, and SWD contained in the Polish Norm PN-85/B-02170. The parameters of the mining shocks measured by the Lubin coal mine station were compared with the parameters calculated as per the correlations (regression curves). The average acceleration calculated from the correlations for eight measurements is only two per cent higher than the actual one. But the average frequency of vibrations calculated from the correlations for eight measurements is as much as 2.22 times lower than the actual one. In order to analyse whether that takes place in the whole range of the energy of shocks compared were the results of calculations from the correlations for various magnitudes of shocks and various distances from their epicentre with the results of the measurements. From that it follows that only for the shocks of the highest energies the lowering of the frequency of vibrations by two times causes movement from the higher zone of harmfulness to the lower one (for example from the IV to III). In the one-family houses in Lubin there were the damages that are characteristic for not only for the III but also for the IV sphere of harmfulness as per the SWD scale. That should be explained via further research and maybe it would be feasible to draw out a new correlation to determine the frequencies only for high values of energy of shocks and determine the preciseness of the acceleration and frequency correlations used presently.

Jan 1, 2003

Kalgoorlie Consolidated Gold Mines Pty Ltd is currently developing the 'Super Pit' gold mine in the mining area known as the Golden Mile adjacent to the city of KalgoorlieBoulder, Western Australia. The presence of numerous abandoned mine workings and complex structural geology has required considerable geotechnical input into the determination of the optimum pit slope geometries for both interim and ultimate pit slopes. Slope design is based on detailed site investigation and stability analysis which is balanced with historical operational experience. This paper discusses the process of determining the optimum pit slope angles for each of the stages of the west wall of the 'Super Pit'. The risks associated with slope instability are discussed for each stage.

Jan 1, 1994

By D J. Williams, M S. Zbik, A Shokouhi

There is a considerable difference in the particle size distribution (PSD) of clay mineral-rich coarse coal reject with variations in the test moisture state and the chemistry of the water used for testing. The coarse coal reject tested were collected from Jeebropilly Mine, located in the Ipswich Coalfields of south-eastern Queensland. Differences between the results of dry and wet sieving analysis indicate a significant breakdown of the clay mineral-rich coarse coal reject on wetting-up. Wet sieving caused a breakdown of the gravel-sized fraction to silt and clay size without significant breakdown to sand size. There is also a considerable variation in the results of hydrometer analyses of the clay mineral-rich coarse coal reject with variations in the chemistry of the water used, particularly at the fine end of the particle size range. The waters used included tap water, coal processing water and deionised water. In addition, the method of dispersion applied prior to hydrometer analysis can have a significant effect on the PSD of clay mineral-rich coarse coal reject, with boiling and sonic vibration causing the most breakdown of the clay particles. This paper describes the testing methodology used and the test results obtained, and attempts to explain the results in terms of clay mineralogy and water chemistry.CITATION:Shokouhi, A, Williams, D J and Zbik, M S, 2015. Influence of water on particle size distribution of clay mineral-rich coarse coal reject, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 239–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

The Nagambie heap leach gold mine commenced production of gold in September, 1989. The mine,120km north of Melbourne in Victoria, Australia, was developed by Perseverance Mining Cor- poration Ltd, a junior Australian mining company, with no other operating mines. Gold production to December 31, 1990 was 47,621 oz. The mine is now producing at the rate of about 45,000 oz per year. As of February 28, 1991, resources at the mine are 5.1 million tonnes measured, at 0.65g/t Au while reserves were 1.65 million tonnes at 0.86g/t Au of proven, heap leach ore, plus 0.37 million tonnes at 0.40g/t Au, of dump leach ore. Metallurgical recoveries expected are 80 per cent for the heap ore and 60 per cent for the dump ore. Perseverance Mining Corporation was listed on the Australian Stock Exchange on April 2, 1987, after a capital raising in March that year. At this time the company's issued capital was 4 million ordinary 25ó shares, 3 million of which were issued to the public to raise $0.75 million.

Jan 1, 1991

The Bowen Basin of Central Queensland covers a total area of 3 200 000 ha. The Basin has proven reserves of about 24 000 000 tonnes of coking coal and steaming coal which constitutes about 70 percent of the known coal reserves in Queensland. Large scale open cut coal mining in the Bowen Basin commenced at Moura in 1959. There are now 16 open cut mines operating in the Basin and they collectively mine through about 3000 ha of land each year. Most of the land which has been mined has previously been used for extensive grazing. No mining has yet taken place on cropping land although coal reserves underlie land which has been cropped or has potential for cropping. The primary objectives of almost all of the mining companies operating in the Bowen Basin are to rehabilitate mined land to a stable and productive form which is compatible with surrounding land use which is dominantly grazing. The acceptability of these objectives is considered against the prospect of mining of cropping land and the qualified success of the return of rehabilitated land to grazing uses.

Jan 1, 1987

By S Arnold

Properties of the soil profile fundamentally control water-limited ecosystems. Soil water availability affects vegetation dynamics of plant communities, but is also affected by these communities in return. Understanding this eco-hydrological interplay and the role of physical soil restoration is crucial for successful rehabilitation and management of post-mining landscapes in semi-arid areas. However, uncertainties exist in both the mathematical description of plant communities within ecological submodels and the predictability of future rainfall events. This study uses information gap decision theory combined with an ecohydrological system model to investigate how both uncertainties impact decision-making in the context of ecosystem rehabilitation. A range of management strategies are investigated to identify the optimal soil thickness for successful rehabilitation of native plant communities in Central Queensland. The results emphasise that thicker soils can counterbalance uncertainty in mathematical description of plant communities by increasing the simulated survival probability of plant communities. However, the influence of thicker soils on the robustness of plant communities against a change in future rainfall amount is rather marginal. By allocating an economic value for restoring a particular thickness of soil layer, these results can be used to evaluate the costs of ecosystem re-establishment with regard to two target measures - the survival probability of the plant community and their robustness against climate change.CITATION:Arnold, S, 2012. Finding optimal soil restoration strategies in the face of uncertain future rainfall amount, in Proceedings Life-of-Mine 2012 , pp 91-96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Y Tsukurimichi, D Asahina, T Endo, T Takemura

Scientific knowledge of Mars’ surface morphology and internal geological structure has been accumulated through satellite imagery and numerical topographic data using remote sensing technology, as well as seismic surveys by the on-site lander. Recent studies show that Marsquakes could be caused by the release of strain energy generated by the contraction of Mars. In particular, Marsquakes occur around the graben where many faults are existed and formed regularly spaced patterns. This implies that Marsquakes occur when the stress field of the Martian crust is an extension condition, and normal faults appear on the surface. We focus on the linear relationship between the fault spacing and the thickness of the mechanical layer as an approach to studying the internal structure from satellite images. Mechanical layer is a layer that composes of the same mechanical properties and is mainly bounded by lithology (Narr, 1991; Gross, 1993). The linear relationship between the thickness of the mechanical layer and the joint spacing has been studied and its slope is called the Fracture-Spacing Index (FSI) (Narr and Suppe, 1991). Soliva, Benedicto and Maerten (2006) showed that the stress drop zone (stress shadow) due to the fault activities affects the fault spacing. Figure 1 shows the approach used to estimate the thickness of the mechanical layer from the fault spacing on Mars. This paper aims to better understand the internal mechanical structure of Mars estimated by the geometrical pattern of faults on the Martian surface. We report the initial studies of this work. The lab-scale physical experiments and numerical experiments were presented to demonstrate the relationship between the thickness of the mechanical layer and the geometric pattern of fractures

Nov 29, 2022

By F Melcher, M Wiedicke, A Wittenberg

Ferromanganese nodules form a specific category of widespread marine mineral deposits. The tremendous increase in metal prices during the last decade raised new economic interest in their exploration. The German Federal Institute for Geosciences and Natural Resources (BGR), which had been engaged in nodule research in the 1970s and 1980s, renewed its activities on this subject based on an exploration contract with the International Seabed Authority, signed in 2006. BGRÆs licence area û comprising 75 000 km2 û is located between the Clarion and the Clipperton Fracture Zones. In this so-called nodule belt north of the equator the sea floor reaches water depths of >4000 m. About 900 million tonnes of manganese nodules are expected there. In this study the fine-scale distribution of important elements in manganese nodules and crusts from a variety of locations was investigated. Besides 11 samples from the RV SONNE cruise SO-25, numerous samples from additional locations were included in this study for comparison. In general, the sample suite includes two genetic types of precipitates, manganese nodules and Co-rich crusts. A detailed characterisation of the distribution of major, minor and important trace elements in manganese nodules based on in situ microenergy dispersive X-ray fluorescence (¦-EDXRF) analysis is presented here. The data are compared with bulk major, minor and trace element data as well as with quantitative electron probe microanalysis (EMPA) data sets. The element distribution maps and profiles produced by ¦-EDXRF analysis with short or extended (in case of profiles) counting times, allow precise selection of æregions of interestÆ for further detailed investigation using high spatial resolution techniques (eg scanning electron microscope (SEM)-EDAX; laser ablation-inductively coupled plasma mass spectroscopy (LA-ICPMS); isotopic studies).

Jan 1, 2008

Disastrous earthquakes are a reality on the Australiancontinent. Unfortunately it has taken the fatal 1989 New-castle earthquake to demonstrate to all Australians that we do not reside on a "stable continent". While the world accepts the potential of plate tectonics and its associated plate margin earthquakes, particularly around the active Pacific Rim, the realisation of devastating intra-plate, or continental, earthquakes is only now beginning to take effect. The 1989 Newcastle earthquake provides many lessons on which to further fundamental earthquake research and the applications to the future welfare of human civilisation. To mitigate the earthquake hazard in relation to the devastation to life, property and industry, research must be undertaken with the resulting informa-tion to be included in the nation's disaster management programs. The earthquake hazard is everpresent in east-ern Australia and the major step in its quantification is a more realistic determination of earthquake risk estimates through an integrated study of seismology, engineering, insurance and sociology.

Jan 1, 1990

For the last decade Australia has been the leading exporter of both steam and coking coal. In the ten-year period 1989 - 1998 steam coal exports increased by 93 per cent and metallurgical coal exports increased by 50 per cent. However, profitability of the steam coal sector has been disappointing. The coking coal sector, especially the hard coking coal segment, has fared better but its profitability was more because of its ability to maintain relatively high prices rather than its inherent productivity. Until quite recently the Australian coking coal sector was widely expected to be able to maintain this comfortable state without undue effort for the three major æpartnersÆ; the companies, the State Government and the unions. But coking coal could now be heading down the path followed by steam coal that ends with long-term over-supply and, despite steady improvements in productivity, poor profitability. Steam coal entered the ænewÆ era of long-term over-supply some years ago. Over-supply was due to the rapid increase in production in Indonesia, often from new mines and Australia. AustraliaÆs production rise was underlain by the apparent belief that the best way to lower costs was to increase production. In the first couple of years costs didnÆt fall much but the additional tonnage was sold at lower and lower prices into the spot market. By mid-1998 the difference between the contract price set with Japanese utilities and spot sales was often in excess of $US12 per tonne. Japanese contract prices and tonnages have since fallen significantly. Steam coal has moved from being a product to being a commodity. Any profits are due more to the low Australian dollar rather than inherent mine productivity. Seaborne coking coal trade has been dominated by Australia, Canada and the USA, with the USA becoming less competitive. Unfortunately, when the Queensland capacity expansion was well down the pipeline, the Asian financial crisis occurred and the Japanese economy entered what appears to be a long-term recession. Contract prices fell 18 per cent, tonnages decreased and some mines have been reclassified as supplying lower priced coking coal. The paper analyses past and expected future trends in labour and mine productivity, rail freight and FOB export port cash and total costs of the Australian steam coal and coking coal sectors and discusses the market outlook for Australia. The future economic viability of the industry is analysed and discussed in the light of the rapidly changing global environment.

Jan 1, 2000