Search Documents

Water retention, water loss and delay in tailings storage rehabilitation are major challenges for many Coal Mines. Work by Stewart, Backer and Busch in the early 1980s suggested that there were improvements to be made in tailings dewatering and density by the addition of flocculant. This prompted ACARP, in cooperation with Bulga Coal Management (Xstrata), to initiate a research project investigating the impact of flocculant addition on tailings deposition density, water retention and the tendency for tailings to form surface crusts suitable for subsequent rehabilitation. A polyacrylamide-based flocculant (200 - 250 g/tds) was injected into the tailings line immediately prior to disposal into the impoundment area. The flocculated slurry rapidly released clear water and created a beach due to the immediate increase in deposition density. The deposition density increased from 35 per cent w/w to 61 per cent w/w solids within 24 hours and continued to increase to 75 per cent, seven days after treatment. The water capture at the tailings storage facility improved by more than 90 per cent; water which would otherwise be lost from the circuit through retention and evaporation. The impoundment capacity had nearly tripled due to the improvement in initial deposition density from 420 kg/m3 up to 1163 kg/m3. Four weeks after disposal surface crusts were forming on the storage facility, suggesting that there would be less delay between cessation and tailings storage rehabilitation.

Jan 1, 2008

Australia has a high level of research and development capabilities in government, industry and tertiary institutions. In the- remote sensing fields, we have developed a range of applications in geology, agriculture, infrastructure and environmental monitoring which are very cost effective and applicable to projects in the Asian and Pacific region. Support by the Department of Science through the Scientific Industries Steering Committee has enabled rapid penetration of this technological capability into projects with significant economic and financial benefits. It has also led to the opportunity for development of new sensors and processing systems, through collaborative projects with regional countries, which. will have applications in cloud covered, rainforest, and coastal tropical regions for geological and resource applications.

Jan 1, 1987

By B Cooper

During the design of a new production facility for a greenfields or significant brownfields expansion many design decisions are made driven by an unquestioning objective to achieve 'lowest cash-cost' production costs. In many cases this translates to a design and operating philosophy based on largest-available, single-line equipment. Although acknowledged as an approach that is efficient from an operating cost perspective does this approach always maximise shareholder value? There is an increasing awareness in the mining industry of the value of project flexibility, robustness and value options. The design of a new production facility creates a window of opportunity which should be structured to ensure that project value options and robustness are understood and exploited. This requires the use of emerging valuation methodologies, such as Value-at-Risk and Real Options, as well as tried and trusted NPV/IRR approaches. The paper provides an overview of the basis and application of these less well known techniques in the context of metallurgical plant design. Design guidelines that demonstrate how value options and flexibility can be quantified from both a risk and value perspective are presented. Issues such as use of single versus multiple line equipment, optimum cut-off grade and improved exploitation of the inherent variability of the orebody are also examined. Finally the management issues and approaches to achieving this will be briefly discussed; for example it is common during project development to drive towards increasing certainty as rapidly as possible to facilitate 'accurate' estimation of costs. Understanding and exploiting value options requires a project culture that tolerates, and revels in, ambiguity and uncertainty û something that would make many project teams uncomfortable!

Jan 1, 2008

By M Dunglison, P M. Cameron

Simultaneous mass-balancing of a mineral processing flow sheet results in adjustments to each data point that reflects the accuracy and precision across the full set of data. In this way, all the good work that goes into designing the sampling and analysis protocol for each sample point is leveraged in order to produce a æbetterÆ set of balanced numbers for every sample point in the circuit. Few operating plants employ whole of circuit balancing techniques to produce reported operating results. This situation is changing with the application of mass balancing technology which utilises redundant data for production accounting and metal reconciliation from product to ore source across multiple phases and multiple time periods. Mine and plant data can now generate credible information to improve productivity. Mine and plant personnel can now use consistent data sets for review and planning. Decisions based on balanced data can be made quicker and with increased confidence.

Jan 1, 2005

By J Zeni

In 2001, the Springvale Coal Mine determined a requirement for a 360 m deep vertical airway to ventilate ongoing underground longwall mining operations. The project, referred to as the Springvale No 3 Ventilation Shaft, was completed in 2003 - 2004 by blind boring a 4.25 m diameter hole from the surface to the coal seam at 360 m depth. The shaft was completed with a 3.5 m inside diameter lining made from a continuous watertight steel and concrete composite pipe. Presented from both the clientÆs and the contractorÆs perspective, the following paper describes the process of constructing a blind bored ventilation shaft for this application. Beginning with the clientÆs definition of the requirements and specifications for the shaft, the paper describes the steps followed by Springvale Coal prior to awarding the contract. Springv aleÆs process involved a thorough site investigation including procurement of geotechnical data for prospective contractors and the management of issues relating to safety, quality and the environment. The clientÆs view is followed by a description of the planning and works performed by their nominated shaft drilling contractor, Ardent Underground Pty Ltd.The contractorÆs description of the works includes the details of the blind shaft drilling and lining construction process used for this application. The design of the shaft lining installed at Springvale Coal was the first of its type to be used in Australia. The successful installation of a watertight composite shaft lining and the safety of the method, which did not require any personnel to enter the shaft or the mine, were among the positive outcomes from the project.

Jan 1, 2005

By H Stedman

Integrating exploration and operational blastholes into one database significantly enhances geological modelling. Benefits include: improved coal predictions, stronger interpretation of structurally complex areas, detailed mapping of heat affected coal aureoles and additional roof accuracy for blast designs that deliver better coal protection.CITATION:Stedman, H, 2014. Integrating blastholes into exploration data to improve coal recovery and modelling, in Proceedings Ninth International Mining Geology Conference 2014 , pp 237–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By S Mitra, T Singh, D O’Dea, T Honeyands

Permeability and air flow rate in the bed during iron ore sintering is crucial to controlling the sinter quality and productivity of a sinter plant due to its influence on the flame front speed. In the present work, the permeability of the bed during sintering was analysed by means of measured pressure drop and temperature at multiple points in the bed during sintering. Three different zones were categorised, ie humidified (green) bed, region of maximum resistance (high temperature zone) based on temperature, and sintered bed. Previous work has shown that the maximum pressure drop during sintering was due to several concurrent physico-chemical processes including dehumidification, calcination of fluxes, dehydroxylation of goethite, combustion of coke and melting of granules (>1200°C). To quantify the effect of the different process, sintering experiments were conducted in a milli-pot (diameter 53 mm, height 400 mm) with pressure and temperature measured at same location in bed. The milli-pot was fitted with four equidistant (80 mm apart) taps. Overall, five sections in the milli-pot were analysed for pressure drop at different times during sintering. It was found that in region of maximum resistance, coke combustion and flux calcination were highest contributors with ~35 per cent of the pressure drop when compared to other processes like de-humidification and goethite dehydroxylation which contributed to ~20 per cent and 25 per cent each respectively. The pressure drop contribution of the coke combustion region increased with increasing coke addition rate.

Nov 8, 2021

By S Van Duin, I Porter

This paper discusses how advanced manufacturing technology (AMT), which is fundamentally reliant on and developed via multi-disciplinary skills, has benefitted non-mining industries, and what lessons can be derived from this experience to benefit the mining industry, particularly underground coal mining. Examples of AMT use in æconventionalÆ industry, some drawn from the more than 25 years experience in many different industries of the Automation and Robotics team at the University of Wollongong, are described to show typical benefits, risks and opportunities expected in using AMT. Applying AMT to mining brings many unique challenges and this paper expands on these and then provides practical examples of how a multi-disciplinary team can develop new processes and systems leading to productivity, safety and other benefits for underground coal mining.

Sep 26, 2011

By G Kuntz, V Wall, B New

The prime aim of the Campbell Mine project was to develop a 3D geological model for the Campbell-Red Lake system to contribute to an exploration model for the region. The base data is composed of over 60 years of geological data covering an area of 16 by 8 km, and from surface down to 1830 m depth. This paper concentrates on the methods used in the GeoSpace system for the processing, integration, display and interpretation of such a large and diverse data set. A block model was developed that recorded the relative frequency of each geological feature within each block. The data input for the block models were based on recoding of the Campbell Mine drilling and channel sample databases into lithological, alteration and structural subsets. The value for each geological characteristic inserted into each block is calculated from all available data that falls within the block. Relative and absolute comparisons of the individual variables provide a targeted outcome from which the blocks are coloured for visual inspection. Different combinations of variable comparisons can be evaluated so that required features are highlighted for interpretation. Blocks are displayed to illuminate the ædominantÆ rock type, according to a formula that may be varied interactively to display the features required by the geologist. This flexibility allows rapid remodelling of lithological distributions, commonly highlighting minor lithological packages not readily visualised in, and interpreted from, drillhole traces alone. The 3D geological model was built from the drillhole datasets and old mine plans utilising standard 3D mining, GIS and database software, with several iterations of plan and sectional interpretation. Near surface bedrock geological interpretations were further constrained by low level aeromagnetic data. The Geospace approach employs an innovative technique for visualisation of the distribution of lithological packages and alteration via block modelling. The method utilises the block model format of data handling as it is considered to be more visible than drilling, flexible enough to incorporate a wide range of data sources, and allows for spatial proximity relationships to be investigated. The method is a simple form of processing large data sets so that results are clearly visible. The calculation is much more rapid than estimation procedures, and does not have any requirement for geostatistical interpretation which is also time consuming. Geospace is not unique to any mine environment software and it is expected to be able to be performed in any system. The proper portrayal of the internal structure of the mineralised body will provide practical input to exploration and mining principally in the areas of resource estimation, exploration vectoring and ore/waste characterisation and may be incorporated with other data to include mine support and mine scheduling.

Jan 1, 2003

By H J. J Boshoff

Pit lakes, as a final void after completing open cut mining, are in most cases unavoidable. Initial mine designs and approvals require consideration and assessment of closure objectives, legislation and stakeholder acceptance to ensure suitable understanding of the closure liability. Mining companies undertake studies and engineering during the planning, operational and closure stages of mining to identify closure options for the final voids, which would be sustainable. Without adequate planning prior to and during the life of the mine, options during the closure stage become limited resulting in costly closure works or long-term liabilities. Engineering consultants provide a specialist service in the assessment of long-term pit lake water levels and characteristics. Ongoing advances in mining methodology and technology, coupled with improved data collection and data management aid in a better understanding of the complexities in estimating long-term pit lake water levels and characteristics. Closure objectives developed during the planning stage sets the requirements for long-term pit lake water levels, which could require maintaining a water level and pit water or discharge water quality. A variety of approaches could be used to assess these closure scenarios each requiring specific data and methodologies. Typically, limited data is available during the planning stage, which results in assumptions based on past experience and relevant case studies. Closure assessments are revisited during the life of mine and leading up to the closure stage, during which additional site-specific data is available improving the accuracy of the assessments.CITATION:Boshoff, H J J, 2018. Assessment of approaches, data requirements and methodologies for estimating long-term pit lake water levels, in Proceedings Life-of-Mine 2018, pp 28–31 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By H Höft

Today tunnel segment liners are sealed with corner-vulcanised gaskets made of extruded elastomeric compression profiles. The profile geometries and the elastomeric materials have been further developed in course of time to meet the steadily increasing water-proofing requirements. After 40 years of using such compression gaskets, a wide range of proven standard profile geometries and well-known brands can be found on the market. Even so, there is still potential for further developments and improvement, not only with regard to the water-proofing performance. Permanently increasing cost pressure in the segment production plants demands further developments and new solutions with regard to application techniques. This is an abstract only. No paper was prepared for this abstract.

Mar 8, 2011

By Dmitrievskaya TY, Cheremnykh PA, Kuftinova IV, Yaremenko VN

The comprehensive processing of raw materials and the tendency to waste-free production require the combination of various methods of concentrating mineral resources. Magnetic separation, an ecologically clean method of concentration, is one step in the technological cycle of ore processing, and cleaning and classifying of raw materials. Separators with superconducting magnetic systems cooled by liquid helium are the novel equipment for practical concentration. Recently, high-gradient (HGMS) and open-gradient (OGMS) magnetic separators using the effect of superconductivity have appeared. The separators of the first type are expedient in the head-end of the technological cycle, as they are most efficient for processing of particles 100 ¦m and greater in size. In this case the main task is to obtain pure tailings with a minimum amount of the useful component. This method allows the essential reduction in the cost of the subsequent crushing and grinding, because only the magnetic concentrate is directed to further processing. The separators of the VGMS type are used more efficiently in the final stages of the concentration cycle to condition the end product. The present work is devoted to the theoretical and experimental investigation of the motion of weakly magnetic particles in the working chamber of superconducting separators of the open-gradient magnetic separator (OGMS) and HGMS types. The flat OGMS is equipped by a magnetic system with NbTi racetracks cooled by liquid helium. The chamber is divided into zones by partitions parallel to the plane of the magnetic system. It is shown how, depending on the number of the zones and their depths, the extraction function of the OGMS varies and the transition from the OGMS to the HGMS occurs. The particles 2 mm and less in size are considered. The extraction parameter distribution of the particles was measured for a multicomponent weakly magnetic ore. It was experimentally shown that xD2 is the extraction parameter for the particles in the OGMS on condition that (p-po)D /l8/tl/g

Jan 1, 1993

By M Hassall

There is a plethora of activities that have been, and continue to be, performed to improve the health, safety and well-being of workers involved in resource industry activities. These activities include implementation of risk management systems, performing risk assessments, constructing bow-ties, implementing critical control management systems, undertaking personal, process and functional safety initiatives, implementing psychological and physical health as well as industrial hygiene programs. Despite the significant work that has occurred over the last several decades, unacceptable levels of fatalities, injuries and illnesses continue to persist as evidenced by Safe Work Australia statistics.

Apr 16, 2024

By R Polmear, G Mauger

You wouldnÆt start excavating before testing core samples, so why would you approve a project plan before all factors have been identified, reviewed and addressed? Even a champion sports team made up of the best players canÆt produce optimal results without a well understood and agreed game plan. Could an F1 racing team produce their outstanding performance without rigorous evaluation and testing of the factors for successful performance? Why would we expect a capital works project team to be able to get it right without an understanding and an involvement in setting and implementing the overall game plan and without an understanding of all stakeholder requirements? For International PowerÆs Hazelwood (IPRH) mine in Victoria, the challenge was development and delivery of a 40 year mine plan, ultimately involving relocation of existing mine operations into an adjacent new coal field, land acquisitions and major environmental and other approvals to allow diversion of three streams, a highway, an Over Dimension route and other infrastructure in a political and environmentally sensitive atmosphere. The lessons from International Power HazelwoodÆs (IPRH) experience are: that the clear set of project principles and guiding values ensured delivery of a robust plan; a robust plan can withstand significant change; and value management (VM) played an important role in providing assurance, to all, that the plan was sound at both the strategic and micro levels. This Hazelwood mine project included five major VM workshops. The first was a critical review process in addition to design and cost reviews. This VM workshop was used to analyse, at a high level, the preferred coal mining sequence and design concepts, together with the interaction between design elements, risks and costs. In addition to this, the workshop provided an agreed common pathway for all downstream decisions. A second VM study was conducted to ensure that the proposed plan and design for relocation of the conveying systems from the existing mine into the new field were planned for optimum achievement from a whole of life cost, time, operational and maintenance perspective, plus the logistics of continuing operations while relocating assets. A third study followed to review the Conveyor Transfer Alliance and review functional design. A fourth VM study workshop was formed at the start of Phase 2 Alliance to ensure that the best value for money was being achieved through the current design, schedule and project arrangements and that all interfaces between parties had been reviewed and responsibilities were clear and understood. Other studies are outlined later in this paper. This paper details the evaluation criteria and processes used in the project evaluation that led to the WestField Mine Development.

Jan 1, 2007

By AJ LYNCH

Broken Hill metallurgists have been responsible for some of the most important developments in mineral processing technology. These occurred mainly in two periods, 1902 - 15 and 1955 - 70. Mineral flotation was developed as an industrial process during the first period and this happened in two stages, the recovery of zinc minerals from the tailings dump accumulated during the gravity concentration of the oxidised ores and the selective recovery of galena and marmatite during flotation of the primary ores. During the second period fast accurate analytical procedures were developed to provide rapid assessment of process performance, and new means of controlling the process were devised which improved throughputs, grades and recoveries. These technological successes were due to the skills of the metallurgists and the commitment of the companies. They brought large financial returns. They were achieved under difficult circumstance. There are important lessons to be learnt from these successes.

Jan 1, 1992

By Richmond AJ, Allan J

The use of long-hole in-seam drilling techniques for seam gas drainage ahead of mining was introduced to the Australian coal industry by ACIRL in mid-1981. ACIRL's research program has involved the development and demonstration of drilling and borehole survey technology in addition to evaluating the gas drainage potential of long-hole in- seam boreholes. This paper presents the results of the long-hole drilling carried out to date in the Illawarra District of the New South Wales coal fields. Drilling experience in relation to both vertical and horizontal directional control of the drill string, drill performance and borehole survey techniques are discussed. In addition, results of gas drainage effected by the long boreholes are presented. Future potential and requirements for further development of this technology are Reviewed.

Jan 1, 1982

By L Smith, R Beckie

An intermediate scale (8 m + 8 m + 5 m high) constructed waste rock pile experiment was built upon a contiguous grid of 16 gravity drainage lysimeters to investigate the flow of water in unsaturated waste rock. Average net infiltration to the uncovered waste rock pile is 55 per cent of precipitation. Large rainfall events have net infiltration of 55 per cent to 85 per cent. Net infiltration estimates range from 23 to 120 per cent of precipitation between lysimeters. Small-scale lysimeters of less than 4 m2 area are shown to be poor predictors of net infiltration for uncovered waste rock. The appropriate size for lysimeters increases with increasing flow rate. The residence time distribution has an estimated median value of 3.0 to 3.9 years under average infiltration conditions. Water flows within the fine grained matrix, within larger pores (macropores), and in matrix free areas of the pile. In situ tracer concentrations vary between pore sizes, and between spatially distinct areas of the pile, indicating water geochemistry may also be variable. Water samples collected from in situ soil water samplers are dominated by the most mobile water fractions. In situ measurements of water content and matric suction are compared to the measured outflow. The data indicate the focusing of flow in spatially distinct areas can make in situ instrumentation a poor (non-conservative) predictor of volumetric water flow.

Jan 1, 2003

By J Krahn

In designing climate exposed soil structures such as caps and covers over mine waste it is necessary to include the wetting and drying influences of the local climate in order to accurately predict the net water, vapour and oxygen fluxes across the ground surface and through the base of the covers. The most advanced evaporative flux modelling tools currently available to practitioners have been limited to rigorous one-dimensional models (ie SoilCover) or semi-empirical two-dimensional models (ie Hydrus-2D). It is common practice to use the rigorous one-dimensional evaporative flux model results to develop a surface boundary function that can then be applied within a saturated/unsaturated two-dimensional model. However, this is not an ideal situation and results in a further approximation of the real system being modelled. This paper will highlight the use of a new modelling tool, VADOSE/W, which brings existing, rigorously formulated evaporative flux theory into the familiar setting of a two-dimensional model. The model is enhanced for simultaneous two-dimensional oxygen gas transport analysis, which has direct application in the mine waste industry. A key focus of the paper will be addressing the limitations of one-dimensional analysis for cover systems on sloping and hummocky terrain.

Jan 1, 2003

The development of Mount Isa Mines Limited power supply is traced through the history of the mine operations. As would be expected, growth of the power supply system follows closely the increase in mine output, although it will be seen that total kWh. produced per ton milled shows a considerable reduction in later years when the mine output showed a more rapid rate of increase. That this reduction is not more marked is possibly due to the increased community and Shire Council power usage per head of population.INTRODUCTIONThe geographical position of Mount lsa, far from any large regional power supply Authority, dictated the policy that the Company be responsible for the production and suppiy of all power required for the plant operation. The Company also, in November 1937, accepted responsibility for the supply of a part of the power requirements of the township of Mount Isa. The history of power supply to the Mine may be divided into several phases.1. The supply Of lighting and power during the first plant construction period 1929-1931.2. The construction of the first section of the Mines Power Station, comprising Nos. 1 and 2 turbo alternators and boilers.3. The addition of No. 3 turbo alternator and boiler.4. The addition of No. 4 turbo alternator and boiler.5. The addition of No. 5 boiler.6. The addition of a. 2 turbo blowers for air supply to the Copper Smelter converters; b. 1 turbo blower for air supply to the L.ead Smelter; c. 2 turbo compressors for compressed air supply to the Mine and surface plant.

Jan 1, 1961

We are all no doubt aware that with today's high costs it is more important than ever to get the maximum possible return on capital invested in the mining industry. Screening is an important and often costly process in the size classification of industrial minerals and for this reason alone it is essential for both managers and operators to fully understand what type of screening equipment is best suited for a particular application and why. The advent of elastic materials such as rubber and polyurethane have added a new dimension to the process of screening. It is important to understand why the physical properties of these materials can be of benefit in the screening process, and recognise which type of screening applications best take advantage of these orooerties.

Jan 1, 1984