Search Documents

The Honeymoon Well nickel sulphide deposits are located in the Agnew-Wiluna greenstone belt, about 45 km south of Wiluna. Both disseminated and massive sulphide nickel deposits are hosted by komatiitic rocks within the deformed and metamorphosed Honeymoon Well ultramafic complex. Fresh ultramafic bedrock is covered by up to 50 m of highly conductive transported material which greatly hampers both exploration and understanding of the bedrock geology. In the early-1970s, mineralisation was discovered by diamond drilling geochemical anomalies defined by wide-spaced percussion drilling over ultramafics that had been outlined by ground magnetics. Subsequent drilling has defined a resource of 158 Mt at 0.71 per cent nickel (based on 0.4 per cent nickel cut-off, 300 m below surface, December 1995) in four deposits. Over the life of the project a wide range of geophysical techniques have been used including airborne and ground magnetics, time domain clectromagnetics (EM), induced polarisation (IP)/resistivity, gravity and downhole techniques including EM, IP and physical property Measurements.

Jan 1, 1996

Sishen uses a state-of-the-art tracking system to track material from its position in blast blocks through various stockpiles and crushers. Qualities are blended directly to the crusher as opposed to blending from stockpiles. This poses an interesting challenge to the planning department to simulate these conditions. The software used in these simulations are Whittle 4X and Maximiser for long-term planning, Xpac for medium-term planning and Mine Works Planner for short-term planning. Geological models and mine design layouts utilise Surpac. Sishen introduced Xpac a number of years ago; the system has developed and changed over the years. With the Sishen Expansion Project (SEP), which aims to utilise low-grade material, major changes to the planning process have to occur. SEP requires that the mine have two different plants, which utilise two different ROM feeds and have different beneficiation curves. Xpac is used to produce a rolling 18-month plan, which is as close to actual operations as possible. In order to do this, the simulations have to take into account the plants beneficiation curves, stockpile movements, hauling distance and equipment needs. On top of this, the schedule has to continually consider specifications for Fe and the contaminants. Plant yields also have to be kept within a certain bandwidth. Xpac is used to simulate the above parameters, as well as generate the raw data required to produce a mine budget. The paper will also show how the 18-month planning process and subsequent planning processes are measured and aligned. Xpac has proved to be an excellent tool to achieve these goals.

Jan 1, 2005

By X Yang, T Zhang, Z Li, Z Yan, M A. Williams, S Qin, P Wilson

Continuous development of complex new steel grades to meet the ever-increasing demand of high performance causes recurrent issues in steel continuous casting such as surface quality defects (eg cracks, depressions, deep oscillation marks) and productivity challenges (eg faster casting, near-net shape casting). Continuous casting of steel is a highly successful metallurgical process. Much of this success can be attributed to the performance of the casting powder that is added to the top of the mould, creates a liquid slag pool as it is heated, and forms a slag film between the watercooled copper mould and steel shell during its passage down the mould. Mould powder selection is a compromise between the conflicting requirements of heat transfer and lubrication. In an EU RFCS (Research Fund for Coal and Steel)-funded project, various techniques are developed to offer the opportunity to adapt the slag film to meet the conflicting needs in different parts of the mould such that mild cooling can be generated in the meniscus, mid-broad face or corner areas whilst maintaining lubrication and offering higher cooling rates in other areas of mould. This has significant potential to address the industrial issues in product quality and productivity of continuous casting. This paper reports, as part of the EU RFCS project, the determination of crystallinity and porosity in slag films for casting challenging and innovative steel grades using new methods. In comparison with the methods such as X-ray powder diffraction (XRD) analysis and optical microscopy / scanning electron microscopy (OM/SEM) analysis that are currently adopted by the industries, EBSD (electron backscatter diffraction) has been employed to determine the crystallinity of the slag films taken from industry casters. X-ray computed tomography (XCT) plus 3D image reconstruction has been used to determine the slag film % porosity with pore volume, pore size distribution, and pore location, which can be linked with the performance of the slag films during casting different steel grades.

Jun 19, 2024

By I Lipton

The existence of metalliferous mineral deposits on the deep-sea floor has been known since manganese nodules were discovered in the Arctic Kara Sea in 1868. Modern exploration to define commercially viable base and precious metal deposits began in the 1970s and gained further momentum in the last decade. High grade deposits have been delineated but investors remain cautious, many considering deep sea mining projects to be riskier than terrestrial projects. This paper compares opportunities and risks presented by terrestrial mining projects with those presented by deep sea mineral deposits (Table 1). The Solwara 1 volcanic-hosted massive Cu-Au-Ag sulphide deposit, the Atlantis II Deeps sedimentary base metal sulphide deposit, and the Mn-Ni-Cu-Co nodule deposits of the north-eastern Pacific Ocean are used as examples. These are advanced deep-sea projects with published Mineral Resource estimates, on the cusp of development. Off-shore diamond mines in Namibia are also considered. These examples provide a basis for comparing exploration and geological uncertainty, the technical risks of proposed mining systems, and the potential environmental and social impacts. CITATION: Lipton, I, 2018. A comparison of opportunity and risk in deep-sea and terrestrial mining projects, in Proceedings Complex Orebodies Conference 2018, pp 102–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A Kite

Frontline leaders play a critical role in the safe and productive operations of Australia’s mining, resources and heavy industries. These leaders set the workplace culture, especially during night shifts and weekends, by providing team direction and encouragement, providing access to resources, fulfilling statutory requirements, enacting and reinforcing risk management systems, setting the standards on shift and acting as the primary conduit of communications between senior leaders and team members.

May 5, 2022

The conventional approach to the disposal of fine coal mine tailings, which involves piping the tailings as an aqueous slurry to a storage where they remain in the form of a permanent wet deposit, is becoming unacceptable. This approach is a legacy of a "contain and forget" mentality, which has economic advantages only in the short term. In the longer term, wet tailings deposits occupy large areas of land and present extreme rehabilitation difficulties. Alternative tailings disposal systems, which are sustainable and which facilitate rehabilitation, are required. The possible alternatives include the mechanical dewatering of fine tailings prior to disposal in combination with coarse reject, tailings disposal into spoil pile valleys, and the combined pumping to disposal of tailings and coarse reject. The most appropriate choice of fine tailings disposal strategy will vary from mine site to mine site. The chosen strategy should be optimised to meet increasingly stringent environmental requirements, within the constraints imposed by each mine. The alternative approaches represent significant departures from past practices, and require considerable industry driven research and development before they can be adopted with confidence. All three alternatives involve mixing of the fine tailings and coarse waste streams, aimed at creating a mixture of reasonable engineering properties. Understanding the engineering behaviour of such mixtures is central to the success of these alternative disposal strategies.

Jan 1, 1991

By J R. Taylor, J A. Muchan, S M. Pape, B S. Davis

Acid and metalliferous drainage (AMD) is routinely derived from waste rock, tailings, pit wall rock, underground mine voids, heap leach pads, ore stockpiles, concentrate stockpiles and even slag piles. In many jurisdictions, there is an assumption that tailings materials represent the highest AMD risk. This is likely due to their highly sulfidic and ultra-fine grained nature, and the fact that they occur in large tonnage, partially unsaturated deposits. These characteristics are not unreasonably associated with reactive and therefore highly polluting mine waste materials. Interestingly, however, the high sulfide content and highly reactive nature of tailings achieves the rapid consumption of oxygen in tailings pore spaces. This oxygen depletion can limit or halt sulfide oxidation throughout much of the tailings pile. Oxygen can only be resupplied to the tailings via atmospheric exchange at the air-tailings interface. The grain size of most tailings materials limits this resupply to a diffusion related process that only affects the uppermost 100–2000 mm. Hence sulfide oxidation in tailings can be inherently self-limiting. Unfortunately, the same cannot be concluded for waste rock materials.Using a unique site assessment strategy that focuses on quantifying acidity fluxes from various domains at a mine site, it has become increasingly evident that sulfidic waste rock produces the majority (typically 60–80 per cent) of the soluble acid and metalliferous pollution at most active and decommissioned sulfide-bearing mine sites. Whether sulfidic waste rock is disposed in engineered above ground facilities, backfilled into pits or even underground voids, it remains the primary source of pollutants for decades to centuries.Conventional end-dumping waste rock practices result in angle-of-repose pathways for air and water, and these internal fabrics exacerbate sulfide oxidation (ie pollution generation) and discharge from waste rock materials. The primary aim of many cover systems is to retard the access of air and water to these conduits. Recent thinking is that more emphasis needs to be directed at strategic waste rock pile construction practices, and less reliance placed on thin soil cover systems to prevent AMD.Waste rock pile construction approaches that minimise porosity and permeability but raise the retained moisture content and enhance water residence times have the potential to lower sulfide oxidation rates and thereby improve water quality outcomes. For example, innovative base-up, layered and compacted (BULC) waste rock piles have the potential to avoid or minimise the generation of AMD, supersede the need for treatment and facilitate successful closure and relinquishment across the mining sector (Figure 1).CITATION:Taylor, J R, Pape, S M, Davis, B S and Muchan, J A, 2016. Waste rock pile construction to lower closure and relinquishment costs, in Proceedings Life-of-Mine 2016 Conference, pp 97–99 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By A Harris, L Balzan

Accurate measurements of the moisture content of iron ore have increasing importance in modern mining operations. Knowledge of the moisture content allows process control actions to be carried out to ensure that the moisture is within prescribed limits, whether this is ensuring sufficient moisture to be above the dust extinction limit or that the moisture level is below the transportable moisture limit for sea shipments. Additionally, controlling moisture within desired limits can allow for greater throughput of iron ore by limiting the amount of water transported. There are a range of options available for operators wishing to obtain moisture data, though there are few demonstrated and proven devices that are able to provide real-time analysis of the full bed-depth of material. Scantech’s through-belt moisture systems are able to accurately analyse the full bed-depth of conveyed iron ore in real time using its unique microwave transmission technology, providing valuable data for operators. Recent advances in these systems have overcome errors associated with the highly attenuating nature of iron ore, particularly for large conveyor belts and deep ore. Furthermore, analysis of different ore mineralogy and its effect on the accuracy of moisture analysis has been examined and quantified. This paper discusses some of these recent results, demonstrating achievable accuracies in spite of changing ore mineralogy. Scope for future work is also briefly discussed, concluding the paper.CITATION:Balzan, L and Harris, A, 2015. Real-time through-belt moisture analysis for iron ore, in Proceedings Iron Ore 2015, pp 539–542 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Anglo American Metallurgical Coal (AAMC) manages five open cut coal mines in Queensland and New South Wales, producing approximately 30 million tonnes per annum. The size and complexity of these mines require efforts by a large and diverse number of personnel to minimise adverse geotechnical events from occurring. To achieve this, the AAMC coal mines in Australia are developing a concept of managing the geotechnical risks associated with open cut coal mines. The overall system utilises a combination of internal training, a management system (operational management systems) and standards, numerical modelling, monitoring, inspections and audits. The development of the standards as well as training and mentoring of exploration personnel, geotechnical engineers, engineering geologists and mining engineers with an interest in the geotechnical aspects of mining, training of the production workforce, mentoring and training of the technical staff create the basis for achieving a pro-active rather than a reactive system. Audits are used to assure that personnel are maintaining the standards and to facilitate cross-mine leanings so that best practices are developed across all sites.

Nov 25, 2010

By Heyer T, Wasmuth H-D

The concentrator plant of Fahrica Mine, that started production in 1977, was using nine Jones wet high intensity magnetic separators (WHIMS) of the standard type DP 317 with a 1.5 mm gap width for the production of pelletfeed concentrate. These WHIMS units were operating in parallel with a feed rate of 110 t per hour, with about 47 per cent Fe in the feed, and with a maximum of only 0.8 per cent magnetite. The field strength was about 1.2 Tesla. From 1986, the mine has adapted its production facilities to mine and concentrate larger amounts of lowgrade itabintes to maximise the use of the available iron ore reserves. An increase of up to three per cent magnetite in the magnetic separator feed, resulted in a reduction of capacity. This was due to partial clogging of the separation boxes at high field intensities, which were required for the recovery of the very fine hematite. Even by lowering the feed rate and the field intensity the problem could not be resolved. After extensive testwork in a pilot plant, with a Jones separator model DI' 90, the commercial WHIMS plant was modified into a two stage process using the existing nine Jones separators. The gap of the first stage with four machines was increased to a width of 3.5 mm, corresponding to a maximum field intensity of 0.7 Tesla. This first 'medium intensity scalping stage' is followed by a second 'real' high intensity WHIMS step with five machines operating at the original settings with 1.5 mm gap width and 1.0 Testa maximum field intensity. Feed rates of up to 320 tons per hour in the first and up to 240 tons per hour in the second stage could be achieved. The design concept of the concentrator at Fabrica mine is described using the old and new flowsheets. Details of the pilot plant testwork as well as actual performance data of the new plant section are presented.

Jan 1, 1993

Modern minerals projects face serious challenges in earning and maintaining acceptance by their key stakeholders. Factors which underpin effective response to managing these challenges include consideration of public affairs issues from the earliest planning stages, building robust alliances with a range of influential partners, developing a level of transparency in all operations and decision-making and integrating activities towards resolving key strategic issues. Effective community relations is vital and there are a number of elements common to the best approaches. These include senior management support and involvement, appropriate involvement in project decisions and activities by community members and company responsiveness to community expectations. The project's operations manager and executive team must fully commit to developing the capability and processes to meet these challenges. They require a whole of project response and it is not an option to manage them peripherally.

Jan 1, 1997

The need to solve the problems associated with spontaneous combustion, system of ventil- ation and methane drainage in gassy coal mines has brought about the development of mining and degassing methods which has made possible up to 80% gas recovery in retreating longwalls. Beneficial results also were obtained mostly in the double or multiple-entry systems, but for single-entry systems and for a seam thickness exceeding 3 m, gas recovery rate is still very low. With some single-heading systems, such as those where a return roadway is not maintained in the goaf behind the face line, a new methane drainage technology is practiced. Attempts were made to extract methane from roof holes drilled from offsets in the ribside of the longwall block. The inclinations and lengths of the boreholes were planned and designed on the basis of the geological and mining condit- ions encountered at the time and every second hole was terminated precisely at the point where the previous hole intersected the immed- iate roof goaf area above the face. There are mathematical relations approp- riate to the design of the above drainage systems to give optimum methane recovery under the given conditions. Some examples of drainage have reached 87% recovery and have attained 94% CH4 purity.

Jan 1, 1982

By D Alexander

For nearly 100 years, the flotation plant metallurgist has often wondered what is happening æbeneath the frothÆ. To assist in unravelling this mystery, new technology has been developed as part of the Australian Mineral Industries Research Association (AMIRA) P9 project, to measure gas dispersion characteristics (such as gas hold-up, superficial gas velocity and bubble size) in industrial flotation cells. These measurements have been conducted in a large number of cells of different types and sizes by researchers from the Julius Kruttschnitt Mineral Research Centre (JKMRC) and JKTech. A large database has been developed and the contents of this database are described in this paper. Typical cell characterisation measurements show a wide spread in values, even in the same cell types and sizes performing similar duties. In conventional flotation cells, the typical gas hold-up values range from 3 - 20 per cent, bubble sizes range between 1 and 2 mm, and superficial gas velocity ranges from 1 to 2.5 cm/s. The ranges of cell characterisation measurements given in this paper will enable plant personnel to compare their operation to other similar types of operations from around Australia and the rest of the world, giving opportunities for further improvement to flotation plant operations.

Jan 1, 2005

For too long we, as an industry, have borne the brunt of irrational claims, poor science and even worse, journalism with regards to our affect on the environment. To some of us, the overwhelming media attention on greenhouse warming, the polluting outputs of mineral processing or unthinkable depletion of natural resources has left us embarrassed and more unfortunately has turned bright young people away from a career in the minerals industry.This paper shows the hypocrisy associated with an element of the green movement and dispels some general myths on mining disseminated by radical environmentalists.The fallacy of the greenhouse warming effect will be scrutinised by common sense and the mining industryÆs use of land will be discussed and put in proper perspective.Problems associated with safety and emissions and the means to overcome such are discussed briefly.

Jan 1, 2004

By X Li, M-F Zhou

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Yinachang deposit in south-west China contains large amounts of Fe, Cu and rare earth elements (REEs). Apatite in this deposit records complex REE mineralisation and remobilisation processes.Fe-Cu-(REE) mineralisation at Yinachang occurred at ~1700 Ma, and three stages of alteration and mineralisation are identified: Na-(Fe) alteration, Fe-(REE) mineralisation and Cu-(REE) mineralisation. In the Fe-(REE) mineralisation stage, REE-rich apatite formed together with magnetite. In the Cu-(REE) mineralisation stage, fluids undersaturated with REEs interacted with early-formed REE-rich apatite, during which large proportions of REEs, especially light REEs (LREEs), were leached from apatite.At ~840 Ma, apatite experienced a second interaction with fluid. In that process, REEs were removed from the apatite structure but immediately reprecipitated into new phases within the apatite. Thus, numerous REE mineral inclusions including bastnaesite, monazite and minor Y-phosphate occur in the apatite. There are also a very small portion of LREEs that were transported out of the apatite, resulting in the growth of bastnaesite and monazite grains outside the apatite.This study demonstrates that REEs can be mobilised in multistage hydrothermal activities and highlights the significance of fluid compositions for REE transportation and deposition behaviours in hydrothermal systems.CITATION:Li, X and Zhou, M-F, 2015. Hydrothermal rare earth element mobilisation processes in the Yinachang Fe-Cu-(REE) deposit, south-west China, in Proceedings PACRIM 2015 Congress, pp 265–270 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The Golden Valley Volcanic Centre has been recently interpreted as being a combination diatreme breccia pipe and rhyo-dacite flow dome complex of Permo-Carboniferous age that intrudes basement granitoids and sediments of Ordovician-Devonian age. Exceptionally good exposure at the Centre has enabled the relationships between different lithologies to be determined. This, along with petrological studies, has led to a detailed understanding of the geological environment in which the complex formed. Gold, silver and base metal mineralisation have been recently shown to be associated with the Marginal Breccia at the perimeter of the diatreme. Comparisons have been made between the geology and mineralisation in this system and several similar diatremes which also contain gold-base metal sulphide mineralisation.

Jan 1, 1990

The planned extraction of deeper copper ore at Isa Mine has necessitated a review of existing equipment and methods to contain costs and improve working conditions. Mining is in progress for a crushing-conveying system to serve the deeper southern areas of the 1100 Orebody. This system will permit direct tipping of ore to the crushers and conveying of the crushed ore by cable belt conveyor to existing shaft loading facilities, a distance of about 2 km. To develop part of the conveyor drive a new machine will be used, the Robbins MM120 Mobile Miner, a joint development project between The Robbins Company and Mount Isa Mines Limited. The Mobile Miner uses a rotating cutting wheel to excavate headings 3.7 m high and from 4.7 m to 7.5 m wide. To ventilate the deep crusher complexes and associated development at high virgin rock temperatures, a refrigeration plant will be built on surface to reticulate chilled water underground. Bulk cooling of air to the 3000/3500 Orebodies and the southern crushers will be combined with the reticulation of chilled service water to the lower workings of the mine.

Jan 1, 1984

Australia as a leading producer of mineral sands has also occupied a leading position in many areas of research'in the processing and applications of these minerals. Research in upgrading ilmenite to produce synthetic rutile has resulted in the develop- ment of many processes, e.g,., Becher, Murso, Chlorine Technology, and ICI processes. Studies on the reducibility of ilmenites, aqueous leaching of reduced ilmenites, Fe-Ti-O system, leachability of natural and treated ilmenites in hydrochloric acid and selective chlorination of iron from ilmenites have been carried out in order to develop and improve the efficiency of the above processes. While research on the processing of zircon sand to produce high purity (99.99% ZrO2 zirconia powder and zirconium chemicals started only recently, research by CSIRO in the early 1970s led to the discovery of the phenomenon of transformation toughening in partially stabilized zirconia (PSZ) ceramics. Australia, with very significant resources of lanthanide-containing ores, pro- duces substantial quantities of monazite each year but research in processing and appli- cations of rare earths was neglected in recent years in this country. However, research to improve processes for the recovery of rare earths is now under way and studies on the production and testing of Nd-B-Fe magnets which are 1.5-2 times stronger than the strongest magnets (Sm-Co) currently available, have also commenced.' An overview of the research in the pro- cessing and applications of mineral sands during the last two decades in Australia and its implications for the industry are pre- sented in the paper.

Jan 1, 1986

By A Gustafson, G Shekhar, P Boeg-Jensen

The amount of material extracted from each blasted ring in sublevel caving mines is vital when deciding the overall mine production target. The orientation of the production drifts is normally perpendicular to the strike of the orebody, and rings are blasted from the hanging wall side to the footwall side in a retreating manner. For an inclined orebody, a given ring will contain different amounts of material based on its relative position along the production drift. This layout creates a distinctive problem with respect to the extraction ratio optimisation along the axis of the production drift. This paper describes the current drawpoint control strategy practiced at LKAB and presents the variation of drawpoint performance parameters along the production drifts. It uses automatically generated data from a bucket weighing system that measures tonnage drawn per bucket, and it classifies the blasted rings into four zones based on their relative position along the production drift. It considers the loading procedure for blasted rings at Kiirunavaara mine and analyses the variations in drawpoint performance along the production drift. The paper finds that although the current draw control strategy is sensitive to ring position along the drift, it could be modified to optimise the final extraction ratio.CITATION:Shekhar, G, Gustafson, A, Boeg-Jensen, P and Schunnesson, H, 2016. Draw control optimisation along the production drift in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 241–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Ngai WCT

Over 90 per cent of the explosives in Hong Kong are used in civil engineering works. The Hong Kong Government controls all explosives and delivers on a daily basis to each site which it has licensed. Such deliveries need to be arranged the day before actual delivery. With the vagaries of the traffic in Hong Kong, contractors do not necessarily know the time of arrival of explosives. Contractors in general would like to reduce their exposure to these potential delays and the high cost of explosives deliveries. The high population density and urbanisation means that rock blasting has to be carried out in close proximity to other property. In order to protect life, property and utilities, it is not only necessary to employ proper blasting techniques but also to adopt effective safety measures. The Route 3 Advance Earthworks project is located on the north-west corner of Tsing Yi Island, Hong Kong. It is one of the Airport Core Programme projects for the new Chek Lap Kok Airport. Secured by Leighton Contractors (Asia) Ltd in early-1992, the work commenced in May of the same year, with completion and handover to the Hong Kong Government in May 1995.

Jan 1, 1995