Search Documents

By A Campbell

Open pit blasting at Ernest Henry Mining has the potential to cause damage to nearby underground workings. This paper is a case study of the blast vibration management project that was conducted to ensure open pit blasting did not adversely affect the stability of upper production levels or cause damage to the underground primary fan units. The two upper levels of the underground mine surround the lower portion of the open pit mine. The remaining underground mine workings are directly below the open pit mine. This paper details the process developed to prevent open pit blasting causing excess vibration in the underground mine. Measurement of test blasts combined with historic blast monitoring data was used to determine site specific blast vibration parameters. Threshold vibration levels for blast-induced damage to underground drives and the fan chambers were developed from benchmarking and non-linear numerical modelling. A Monte Carlo simulation model was used to predict vibration levels in critical underground areas. Blasts predicted to exceed maximum vibration levels could then be redesigned to avoid damage.A scale distance law for determining peak particle velocity (PPV) from the distance and charge weight of blasts was developed. Underground observations were used to develop a site-specific relationship between PPV and ground support/rock mass damage. A Monte Carlo superposition prediction model was developed and compared to measured data to refine input parameters. Standards for redesigning open pit blasts in order to reduce blast vibrations whilst minimising impacts on productivity are described. Non-linear numerical modelling was used to establish the dynamic capacity of the fan chambers, and set a PPV of 250 mm/s as a threshold for damage. The numerical model captured the full dynamic behaviour of the fan chambers and installed support, including transient stresses, strains and induced damage, when subjected to a simulated open pit blast.This case study also outlines a procedure for monitoring and predicting blast vibrations at other mine sites where open pit blasting has the potential to impact on a nearby underground mine.

Nov 8, 2011

Mining companies in Australia have grown in size and complexity over the past 20 years. The same period has seen exten- sive changes in the operating environment, with greater competition and intensified in- dustrial and social pressures placing new demands 'on mining activity. The new condi- tions require a management approach that emphasises strategic planning rather than operational efficiency. Strategic management evolves through four distinct phases, namely, financial planning, forecast-based planning, externally oriented planning and 'true' stra- tegic management. The most difficult transi- tion to make is from Phase 2 (forecast-based planning) to Phase 3 (externally oriented plan- ning) since management is often too involved in operations to find time to develop and main- tain a strategic orientation towards the mar- ket and competitors. Reorganisation of re- sponsibility for operations and improved op- erational processes enable management to concentrate on external opportunities.

Jan 1, 1980

By S Fityus, K Koosmen, J Simmons

The purpose of this paper is to therefore investigate the hydrogeological characteristics of tailings, coarse and mixed rejects from coal processing to enable better understanding of the potential for undrained behaviours in coal mine spoil piles. This is achieved by analysing the results from permeability and oedometer testing of tailings, coarse rejects and mixtures thereof. Focus is given to the effect that tailings content has on the behaviour of mixed rejects, the transition point between drained and undrained material behaviours, and the evolution of properties with increasing stress that would occur with increased depth of burial in a mine spoil pile. The implications of the findings are discussed with respect to spoil pile stability.

Jul 1, 2021

By A Hughes, S G. Rosin

This paper presents the design and construction approach adopted for the widening and stabilisation of the existing decline tunnel forming part of the Scenic Railway Upgrade project at Katoomba in the Blue Mountains of New South Wales (NSW), Australia. The overall upgrade project included new trains and track, rebuilding of the top and bottom station and installation of a new winch and control system. All the works were undertaken over an eight-month period between August 2012 and April 2013 as part of a $30 M upgrade of the railway.The railway is the steepest cable-driven line in the world at a maximum of 52° extending over 350 m and descending from the escarpment into the Jamison Valley. The track was built in the 1880s for coal haulage and is recognised as a remarkable engineering achievement for its time. The tunnel section extends for about 120 m at the start of the decline and is about 3.5 m wide and 3.5 m high. The tunnel was excavated principally within medium to high strength Banks Wall sandstone and given that the widening only involved about 200 mm of trimming of the crown and sidewall this aspect of the work was not a critical support issue, except at the upslope portal. The tunnel crown however is entirely intersected by a major near vertical shear zone which presented significant challenges for the tunnel stabilisation works.Three-dimensional laser survey scanning was used for definition of the tunnel clearance envelope for the widening, and also to subdivide the tunnel into various geotechnical sections to assist in support design. Specifically oriented rock bolts extending beyond the shear zone into stable rock were used together with mesh, shotcrete and extensive strip drains and flushing points for drainage of the shear zone.Unique aspects of this project were included into the specifications and work methods. This included construction of a mobile working platform for tunnel works, the use of dry shotcrete application, difficult access for rock bolting and limiting vibration during the tunnel trimming works due to the risks associated with crown instability. The works also took into consideration particular safety constraints/work exclusion areas to address the risk of detachment of rock which could mobilise downslope to the track area below. This was required because other works were in progress such as micro-piling and bottom platform works which were being undertaken concurrently with the tunnel work.CITATION:Rosin, S G and Hughes, A, 2014. Scenic Railway Tunnel upgrade in the Blue Mountains, New South Wales – an approach to design and construction, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 607–618 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By E Nettleton, A Melkumyan

A probabilistic system for autonomous tracking of excavated ore in mining would be highly valuable. Currently, mine sites can have a vast array of sensors; examples include excavator load cells, bucket volume estimators and haul truck strut pressures which can be used to gather information about the excavated ore at different locations. These sensors can be utilised efficiently to increase the accuracy of mine estimates by introducing a real-time ore tracking system. This requires the introduction of a probabilistic ore tracking framework to consistently fuse information from any sensor input. Current modelling practices are manually intensive, deterministic (no recognition of the quality of data) and generally not a complete end-to-end system. This paper will provide a novel method for tracking extensive ore properties (mass, volume) and intensive ore properties such as chemical composition (eg Fe per cent, SiO2 per cent, Al2O3 per cent). This method is proved to ensure that correct correlations between states are conserved as material is transferred, combined and/or separated at different locations with any configuration of sensor inputs. This ensures that consistency of estimates is maintained and other benefits such as real-time probabilistic reconciliation can be implemented. A method for combining material of different mass and chemical compositions is also developed to enable accurate and efficient operation of the system. Representative experiments on a small-scale and a larger field trial which mimic the mining processes of excavation, haul and unload to ROM Stockpile will be used to verify the approach.

Sep 26, 2011

By M Chaudhari, G Manekar, D Shome

MOIL Limited is operating 7 underground and 3 opencast mines in central India and producing annually more than 1.2 million tonnes of various grades of manganese ore. The underground mines are operating at shallow - 90 m at Munsar mine to moderate - 353 m at Balaghat mine below the surface with horizontal cut and fill (HCF) or its variant method of stoping with post filling by hydraulic sand stowing. The Munsar mine is being worked underground since 1903. The opencast mining is presently stopped. The ore body below the opencast quarry is geological continuity of the area excavated in past by opencast method of mining. The underground mining is done through the adit in three levels i.e. 270’L, 220’L, 170’L and by incline in western part of the property at 70’L. The horizontal drift development has been developed in the manganese ore body with sill drive of 5 m above the sill pillar in lower level at 70’L and barrier pillar of 5 m thickness is left for protection of upper level at 170’L. Valuable mineral has been locked in sill pillar and therefore rock mechanics investigations have been carried out. On the basis of study now the drift development has been carried out in footwall rock at 70’L, (-) 30’L and below levels and it has improved the mineable manganese ore by about 20%. In this modified HCF stope design, an alternative fill material in place of sand, which has been developed in house by use of overburden (OB) material after treatment, has been used for hydraulic stowing. The experimental trials find out that the alternative fill material of OB is more compact and forming a non expansion floor for the men and machines in the stope. This will certainly help in the introduction of mobile underground mining equipment for drilling in the stopes and mechanical mucking, transportation and loading of the ROM. The paper presents rock mechanics investigations and future use of alternative fill material of OB for better safety and productivity at Munsar Mine of MOIL. CITATION:Manekar, G, Shome, D and Chaudhari, M, 2018. Modified ground support with alternative fill material for ground control at Munsar underground manganese mine of MOIL Limited, India, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 58–65 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J A. Meadows, M G. Annandale, G Castelain

Bauxite mining on Cape York Peninsula (CYP) commenced in the early 1960s in the region surrounding the town of Weipa. Rio Tinto Alcan (RTA) operates its bauxite mines on the homelands of 11 Indigenous Traditional Owner groups. The mining activity currently operates under three Aboriginal Agreements including an Indigenous Land Use Agreement – the Western Cape Communities Coexistence Agreement (WCCCA) – which provides RTA with access to the land in return for a range of benefits to the Traditional Owners, including employment, training, royalty payments and future relinquishment of the land (Klimenko and Evans, 2009). Despite reports of some ‘good progress’ in meeting the terms of the WCCCA (Klimenko and Evans, 2009, p 5), many of the region’s Traditional Owners remain dissatisfied. Two key areas of Indigenous community concern are the current premining management practices and the outcomes of post-mining landscape rehabilitation efforts.CITATION:Annandale, M G, Castelain, G and Meadows, J A, 2016. Sustainable mining – indigenous community benefit, in Proceedings Life-of-Mine 2016 Conference, pp 173–175 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

Forty years ago Dr Pierre M Gy, a metallurgist, introduced variography as applied to monitoring a process. Consequently, his followers used the variogram to elaborate meaningful process control charts, especially since 1993. The name æChronostatisticsÆ was suggested several times by Gy as a logical name for this new science. The intent was to draw a parallel between the variogram identifying the variability components affecting a process parameter as a function of time, and the variogram used in geostatistics identifying the variability components of a given mineral content as a function of space. Heterogeneity problems encountered have indeed strong similarities. However, there is a fundamental difference. The variogram used in geostatistics is often stationary within a given type of mineralisation. While investigating a dynamic process through Chronostatistics, there is no such thing as a stationary variogram. Still, the evolving variogram provides essential information about subtle, often overlooked process difficulties. Chronostatistics is especially useful for management to take advantage of existing data that are often a forgotten source of valuable information to pinpoint recurring structural problems. The superiority of Chronostatistics over conventional statistical process control approaches is that it links observations to the inherent heterogeneity of materials under investigation, therefore to the sampling theory. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in-depth way. Several case studies are presented to demonstrate the potency of this new science. For each of them, observations lead to solutions for continuous process improvement, therefore attractive economic opportunities. The philosophy is this: if a control chart shows a process is out of control, it must also suggest logical and pragmatic directions for solutions. The intent of this presentation is to vastly expand on these valuable, almost forgotten ideas.

Jan 1, 2006

By E Thomas, L McCallum, G Dale, J Bennett, K Reardon-Smith, S Raine

Sustainable closure of coal mines in Australia to a safe, stable, non-polluting condition remains one of the industry’s biggest environmental and social challenges. A significant proportion of mines in the Bowen Basin of Queensland have dispersive spoil. Based on an estimated area of 20,000ha and a rehabilitation cost of AUD$100,000 to AUD$150,000/ha, the instantaneous rehabilitation liability for the Bowen Basin alone is estimated at AUD$2 to $3 billion.Dispersive spoils present problems in post-mining rehabilitated landforms due to increased potential for surface and tunnel erosion, compromising the ability to achieve fundamental mine closure objectives of a safe, stable, non-polluting and self-sustaining post-mining landform (Minserve, 2004). Dispersion results in clay particles being mobilised and transported in water, even at low flow velocities (So et al., 1998; Minserve, 2004), and blocking of soil pores, resulting in surface sealing, crusting and reduced permeability (DNR, 1997; Vacher et al., 2004) which, in turn, further increases runoff (Dang et al., 2018).CITATION:Dale, G, Reardon-Smith, K, Thomas, E, Bennett, J, McCallum, L and Raine, S, 2018. A process-based approach to mine rehabilitation decision making using Bayesian modelling and risk-based principles for dispersive spoil rehabilitation, in Proceedings Life-of-Mine 2018, pp 106–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By D Johansson, A Nordqvist, D Mihaylov, N Petropoulos, M Wimmer

The flowability of the caved rock masses in the sublevel caving (SLC) mining method is of great importance. During the blasting process of a SLC-ring, the caved rock mass in front of the ring is compacted. As a result of this compaction, the mechanical properties of the fractured rock masses change, for example void ratio, angle of internal friction and structure of the compacted material. The changed mechanical properties of caved rock mass and recent blasted material can influence the mobility of the material, which could result in blockage of the flow path of the material. The identification of the involved mechanisms in this process can be done after a series of tests in different scales. However, there is no available equipment for dynamic measurements during blasting, ie velocity and displacement of the burden and in the caved masses. This study focuses on the development and laboratory evaluation of a measuring system that can be installed in a borehole. The first trial was carried out in a pillar, where two blastholes had been drilled (9.5 m) parallel with the drift and two measuring holes (16.5 m) were perpendicular to the drift. Two measuring systems were installed in the measuring holes. Some preliminary tests were carried out to find suitable initiation procedures for the emulsion explosive. Applicability and robustness of the developed measuring system were also evaluated. In addition to these tests, an expandable cement mixture was developed to firmly anchor the measuring systems in the boreholes. The measuring system consists of an anchor, armoured cable in a pulling tube and a protective case. The anchor is equipped with uniaxial and triaxial accelerometers. A potentiometric measuring system for displacement up to 2 m is installed at the end of the pulling tube and connected to an extendable spiral cable. All sensors are connected to a data acquisition system (DAS). Both measuring systems have their own DAS to acquire data in case of failure of one of the systems. The measuring system was tested in laboratory conditions with impact velocity up to 10 m/s. It was proven to be functional and gave reliable results.CITATION:Petropoulos, N, Mihaylov, D, Johansson, D, Wimmer, M and Nordqvist, A, 2015. Design of equipment for dynamic burden measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 493–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G J. Lyman

Sampling of grain for mycotoxins is challenging in that some mycotoxins, such as Ochratoxin A (OTA), have very low permitted levels and the kernels carrying the mycotoxin may be highly localised within the bulk of the grain as ‘hot spots’. Sampling for genetically modified organisms (GMOs) can be fraught with similar problems, especially if the contamination is adventitious and random. Incremental sampling under these circumstances can be shown to lead to a high variance in the sampling result.A new design of sampler for grain and other free-flowing particulates has been developed that is effective in practically eliminating the sampling variance due to distributional heterogeneity (DH).This paper introduces the design and argues that the sampler should be free of sampling variance due to DH.CITATION:Lyman, G J, 2017. A new sampler for grain and other free-flowing particulates, in Proceedings Eighth World Conference on Sampling and Blending , pp 277–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

This study examines the application of Landsat TM data to the identification of hydro- thermal alteration in the arid terrain of the El Salvador region of north Chile. Numerical reflectance values were extracted from the digital Landsat TM data for a variety of rock surfaces, including four parts of the El Salvador gossan, for each of six spectral bands. These reflectance values were analysed statistically in order to select the three spectral bands, combined as a colour composite image, that are most efficient in discriminating different varieties of alteration and for general geolog- ical interpretation. The most cost effective com- posite image for this area is a combination of bands 1,4 and 7 as the blue, green and red components respectively, with simple contrast enhancement. This image is superior to some much more expensive enhancement techniques and allows unambiguous identification of areas of hydrothermal alteration larger than about 50m. The display includes a practical guide to the use of Landsat TM imagery for volcanic gold Exploration.

Jan 1, 1987

By P Wilson

The Mt. Wright Underground Mine is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. The establishment of the world’s first Sub Level Shrinkage (SLS) mine from a tradition Sub Level Open Stoping operation has proven to be a geotechnical challenge which has required tailored solutions to overcome unique issues. This paper will be broken into two distinct sections that will outline: a brief overview of the mining method and how the SLS method was chosen; and how the SLS is managed and key geotechnical learnings. The story of the world’s first SLS originated from the need of a bulk mining method to ensure the viability of Mt. Wright into the future. Traditional bulk mining methods such as; Block or Sublevel Caving were originally ruled out due to the low natural ‘cavability’ of the orebody and the proximity of the orebody to existing major infrastructure (Decline, Ventilation Rises and Egresses). The first section of the paper will outline the key geotechnical information that helped decide the SLS method in addition to how continuous backfill influenced the design. The second section is intended to address issues that the geotechnical engineers encountered since the inception of the SLS. The feature topic of this section is mining induced stress. Like most bulk mining methods, Mt. Wright had success when the production front was running parallel to the stress (production front being ‘shadowed’ from the stress). This was until a design change, forced by a splitting ore body resulted in this shadowing effect becoming harder to achieve. As a result, rehabilitation and production hole re-drilling become a regular occurrence, which teamed with a strict set of access controls made the production cycle longer and harder to complete. CITATION:Wilson, P, 2018. Mt Wright – geotechnical learnings from a sub level shrink, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By C L. McIntosh

The west coast of New Zealand’s south island is host to a large number of placer goldfields that stretch from the Westport area in the north to Gillespies Beach in the south and inland to the foothills of the Southern Alps. This area is host to a large number of alluvial, glacial and strand line deposits ageing in range from Recent to Tertiary. In recent years exploration models have been developed for off shore placer deposits on the continental shelf.Gold mining on the west coast has exploited placer gold resources from the 1860s to present, and with the recent surge in the gold price the industry is currently undergoing a resurgence. The current increase in mining is dominated by small-scale mechanical operations usually involving one to two people at each site; a few larger operations also exist such as the Grey River Dredge.Mining methods range from using floating bucket dredges to small diggers. Some of the mining technologies used are similar to those employed during the great gold rushes of the 19th century. Exploration and grade control techniques can be very rudimentary often relying on previous sampling programs or wide spaced bulk sample drill holes. Some bulk sample drilling is used on the larger operations as a form of grade control, most of the small operations tend not to use any ore control sampling prior to mining. Extraction techniques relying on simple gravity based designs with riffle tables or spirals are the most commonly used. Environmental standards are very high within New Zealand and require operators to return mined areas to preagreed to landforms. The high rainfall experienced on the west coast causes challenges to operators in regard to water quality. Technical issues combined with often limited capital provide for challenges to the operations.

Aug 22, 2011

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

By N Kreutzman, A Moilanen, V Palosaari

Carboxymethyl cellulose, CMC, is widely used in mineral processing as a flotation depressant, mainly for the depression of carbonate and talcaceous gangue in the flotation of Cu-Ni sulfide and PGM ores. Although CMC is a common depressant that can be used in the flotation of different ores, understanding of the interaction mechanisms between CMC and mineral particles in different flotation circuits and different pulp conditions is still limited. Electrokinetic measurements, microflotation and laboratory-scale flotation tests were carried out to optimise the action of CMC depressants in the flotation of a PGM ore. Standard and new CMC brands produced and characterised by Noviant were used in the study. Pure talc and chlorite minerals and a low-grade PGM ore composite were used as test materials. A laboratory flotation test evaluation was performed using the recovery-grade relationship and double value index (DVI) calculation to estimate the effects of both valuable and harmful components on the product value. Solution conditions play an important role in the depression of gangue minerals such as talc. The most favourable conditions for MgO depression were found to be mildly acidic in which conditions the electrostatic repulsion between the CMC molecule and talc is minimised. Similar effects were obtained with electrolytes that affect the conformation of the CMC molecule and the mineral surfaces. In addition to the control of chemical conditions in the pulp, CMC molecules were modified to optimise structural variables. The new CMC brands developed in this work showed significant potential to improve flotation performance, particularly when pulp conditions are controlled.

Jan 1, 2005

By A F. Cropp, D J. Bradshaw, W R. Goodall

Mineralogy and critically the texture of both the ore and gangue phases are of paramount importance in the flotation recovery of copper from porphyry ores. Mineralogy and texture will define the theoretical grade recovery curve for a feed ore. Actual grade-recovery falling below this may be due to texture and gangue influences, whilst desired grade-recovery above this line will not be possible unless the characteristics of the feed are altered.This review discusses examples of porphyry copper deposits where process mineralogy has been used to characterise these textural and gangue influences on recovery by flotation. More specifically, the influence exerted by grain size, liberation, association and elemental distribution is explored. The implications of these on overall plant philosophy and operation are highlighted, along with the subsequent potential impact on recovery.CITATION:Cropp, A F, Goodall, W R and Bradshaw, D J, 2013. The influence of textural variation and gangue mineralogy on recovery of copper by flotation from porphyry ore - a review, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 279-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Kavanagh M. E, Henley R. W

The Meekatharra mining district lies in the northern pan of the Murchison Province of the Archaean Ynlgam block of Western Australia. Since dis- covery of the Paddy's Flat belt in the district in 1897 total gold production has been 67 tonnes and a further 33 tonnes in resources have been defined by drilling. The Paddy's Flat gold deposits occur within the Gabanintha Formation, a basal formation of the Murchison greenstone sequence containing komatiitic basalts, ultramafics and minor banded iron formations. The regional control on the distribution of deposits is an anastomosing shear belt which extends over 350 km and incorporates the Mt Magnet, Reedys and Meekatharra deposits. The following gold deposit styles may be recognized based on lithological association and alteration: Albite porphyry hosted, Carbonate-fuchsite- quartz alteration hosted deposits, Banded Iron Formation hosted sulphide replacement gold deposits and quartz vein deposits. With the exception of the banded iron formation hosted deposits, the Paddy's Flat alteration zone shows strong similarities to the alteration styles at Kerr-Addison (Ontario).

Jan 1, 1991

By T Baumgartl, R I. Maczkowiack, O White, P D. Erskine

Queensland legislation, industry codes and policies relating to mine rehabilitation and closure create the expectation of successful progressive rehabilitation and that the post-mining environment is being returned to a condition suited to a pre-agreed, beneficial end use. Yet none of the rehabilitated mined land in the Bowen Basin has been certified as successful by authorities suggesting there is a gap between current rehabilitation and the full environmental outcomes that the legislation could deliver. We tested the veracity of this perspective and reflect on where responsibility for any discrepancy lies.We first reviewed current Queensland legislation and industry codes relating to stakeholder engagement, rehabilitation, closure planning and post-mining land use. We tested the accessibility of the documentation trail for several recent coal-mining projects in the Bowen Basin and examined the level of detail in approval documentation. We then assessed the rehabilitation performance reports of these mines in relation to the contents of their approval documents. Legislation, guidelines and codes repeatedly emphasise the need to plan for closure before mine operations begin and to progressively perform rehabilitation with an agreed end-use in mind. Early stakeholder involvement in these processes and transparency of actions and outcomes are also encouraged by government publications. Overall, in terms of transparency, we found that relevant documents are generally available to the persistent enquirer. However, the rehabilitation and closure undertakings given in both mine company and regulator documentation were commonly generic and rehabilitation obligations were not explicitly incorporated into rehabilitation plans. Rehabilitation reporting was also weak in that no distinction is required between successful and unsuccessful revegetation, nor to closure objectives and mine completion criteria. Responsibility for the apparent disconnect between regulatory intent and actual performance appears to begin with the regulator too readily allowing generic information and in not requiring performance reporting to correspond with approved post-mine conditions. As a result, companies may have a much greater rehabilitation and closure risk than mine management expects. More poignantly, the checks and balances that are in the legislation are not yielding the environmental outcomes of which they are capable.CITATION:White, O, Maczkowiack, R I, Erskine, P D and Baumgartl, T, 2012. Walk or talk - Is the current mine approval process in Queensland delivering rehabilitation and closure success?, in Proceedings Life-of-Mine 2012 , pp 59-68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By D A. F Oliveira, C J. Parker

The role of the virgin in situ stress field in tunnelling projects is well known in the Sydney area. The effect of in situ stresses is mostly considered through the use of published relationships that describe the in situ stress conditions as a function of depth. Considering the significant scatter in the data, it is evident that by adopting such relationships, the designers are assuming an average distribution of stresses with depth that is generally a reasonable engineering approach; however, when building a geomechanical model, the tunnelling or geotechnical engineer needs to account for the interrelationship between ground conditions (rock mass quality – fracturing, strength and stiffness) and in situ stress, which may explain part of the stress data scatter. This paper presents an alternative approach for interpreting in situ stress conditions, valid for both Sydney sandstones and shales that focus on such interrelationship between in situ stress and ground conditions.CITATION:Oliveira, D A F and Parker, C J, 2014. An alternative approach for assessing in situ stresses in Sydney, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 189–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014