Search Documents

By S Bourke, R Stone, B Hill

Since Jameson Cell flotation technology was first installed in a coal flotation application in 1988/89 at Newlands Coal Handling and Preparation Plant (CHPP) there have been fundamental improvements to its design which has led to its current status as the leading technology in Australia for fine coal flotation. These improvements, which include key hardware modifications, consist of the re-development of the orifice plate to produce considerable increase in wear life and reduction in power consumption for a given air entrainment and a significant increase in the amount of air that is entrained. Modifications to the downcomer allow maximisation of residence time and air entrainment while changes to the feed and air distribution system allows a reduction in installation cost and a reduction of solids ingress into the air line. Additionally, operational improvements such as the use of recycle to maintain constant flow to the cell feed are discussed. The recent installation at Hail Creek in the Bowen Basin, which consists of three B6000/20 Jameson Cells (6 m diameter bottom-fed distributor with 20 downcomers) will be reviewed as a case study. The latest design and operability of the cells are summarised and compared against one of the original designs at Riverside CHPP also in the Bowen Basin.

Jan 1, 2005

By P J. Cullen, B P. Banerjee, S Raval

Continuous monitoring of mining impacts on the surrounding environment is a necessary sustainability criterion. Traditional monitoring approaches such as in situ sampling and airborne and satellite-based remote sensing have several limitations. Over the past few decades, unmanned aerial vehicles (UAVs) have evolved into popular platforms for remote sensing. UAV-based remote sensing has been successfully applied in different sectors, including agriculture, forestry, urban environments and disaster management. However, the potential of UAVs for mine environmental monitoring has not yet been fully established. This paper envisages the use of UAVs and sensor systems to monitor the environment of future mines.CITATION:Banerjee, B P, Raval, S and Cullen, P J, 2015. Unmanned aerial vehicles for mine environment monitoring, in Proceedings Third International Future Mining Conference, pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By F P. van der Meer, E Lessing, E Matthies

High pressure grinding rolls (HPGR) technology is growing to be a common comminution tool in iron ore processing. The technology finds a wide acceptance and presents specific benefits in coarse ore grinding and closed-circuit grinding in preparation of ball mill feed, right down to the other end of the particle size spectrum for iron ore pellet feed preparation.A growing number of minerals processing plants are facing higher operating costs and difficulties due to a scarcity of process water, which in some cases is a result of more stringent environmental constraints. In addition, many new iron ore deposits are located in more arid regions of the world. These challenges have led to operators taking a new look at dry processing of iron ores.The use of dry crushing and classification technology in cement production from blast furnace slag, clinker material or limestone feed stocks indicates that the technology may be applied in minerals processing. In addition, dry processing provides the possibility of generating a final product from finely disseminated and inter-grown ores at sizes near or well below 100 µm, as may be required for beneficiation techniques such as in fine magnetic separation, flotation or magnetic flocculation.Dry grinding by HPGR has a number of specific features, challenges and opportunities, including balancing power input, moisture content requirements and classification efficiency in the process design. HPGR parameters and the latest HPGR design and sizing capabilities indicate considerable potential benefits from this dry processing technology.This paper highlights some of the specific issues that play a role in dry HPGR application, with respect to energy and materials balances. Examples of dry HPGR practices and process studies in iron ore mineral processing are discussed.CITATION:van der Meer, F P, Lessing, E and Matthies, E, 2015. Iron ore final grinding by high pressure grinding rolls and air classification, in Proceedings Iron Ore 2015, pp 197–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A T. Spathis, M L. Lawlor-O’Neill

A methodology for the inversion of a scaled charge weight superposition model to predict peak particle velocity (PPV) has been examined. The inversion involves two steps: first simulated annealing is used to get an initial estimate of the model parameters; and second, these parameters are used as input to a quasi-Newton non-linear optimisation method, used to refine the value of the parameters. The methodology recovers the three required parameters (two charge weight scaling parameters and a time window width) and does this directly from a single production blast for a given point of interest. It has been tested on a synthetic example and recovered the input model parameters successfully in the presence of introduced noise with a coefficient of variation ranging up to ten per cent. Another test used the vibration measurements of three tunnel blasts monitored during the construction of the Citybanan tunnel in Stockholm. In this case, the three model parameters are found from one blast and for a given point of interest, and the PPV at the same point of interest is predicted for the second and third blast fired in the same vicinity as the first blast. The three blasts used different firing sequences. The predicted PPV limits use a confidence interval determined from the scatter in the peak levels obtained from the single calibration blast. The methodology was able to predict an upper bound for the PPV in 21 of the 26 tunnel blast vibrations studied. These predictions improve on a previous study involving the same model but which did not use the inversion process above. Given this reasonable success, further testing of the method on other data sets and alternative forward prediction models is recommended.CITATION:Lawlor-O’Neill, M L and Spathis, A T, 2015. An inversion method for the prediction of peak particle velocity in blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 97–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By B J. Hutchison, S Gannon, J Chambers, D Oko-oboh

The Kanmantoo copper mine is located in the Adelaide Hills area of South Australia and is owned and operated by Hillgrove Resources (HGO). The mine is a drill and blast, truck and shovel operation mining sulfide (chalcopyrite) ore located in chloritised andalusite biotite schist. The initial Kanmantoo open pit operation occurred in the 1970s, before falling copper prices closed the mine. In 2010 the mine was reopened by HGO and the Kavanagh cutback of the Kanmantoo pit was undertaken. The Spitfire, Nugent and Emily Star satellite pits were also mined through to 2015 before the latest steep wall Giant pit design was developed to take mining out to 2019.There are no major fault structures and only two significant shear zone structures exposed in the open pit walls. The main Garnet Andalusite Biotite Schist (GABS) unit is quite competent so the pit designs have therefore mainly been controlled by four distinct joint sets. This paper is a case study on the influence of the joint regime on the wall stability of the main GABS unit and how a better understanding of the joint regime and the use of rock reinforcement has allowed the steep wall design to be adopted.The paper also describes the remote geotechnical mapping and slope monitoring techniques used to manage the rockfall risks associated with the steep walled slope design.CITATION:Hutchison, B J, Chambers, J, Gannon, S and Oko-oboh, D, 2017. Case study of joint structure and the design and performance of open pit walls at the Kanmantoo copper mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 355–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

The Hall-Hoult process is likely to be the dominant method of aluminium production for the remainder of the century. The characteristics of the operation of a modern smelter are described and attention drawn to their disabilities which are due chiefly to the small production capacity of individual cells.The principal components of the Hall-H6roult cell - the electrolyte, the anode and the cathode - are discussed in order to identify the problems of scale-up. The factors influencing current efficiency and energy consumption are analysed and lead to the conclusion that the greatest potential for energy saving lies in reducing the anode to cathode distance (ACD).The most promising direction for major change is in the application of a new titanium diboride - carbon composite for coating of the surface of the cathode carbon. It improves the wetting of the carbon by aluminium and should permit the use of sloping cathodes and anodes. The deep metal pad would thereby be eliminated and, in the absence of magnetic perturbations, the ACD could be substantially decreased.The construction and testing of a full-size "Low Energy Cell" is scheduled for early 1986 and is expected to reduce energy consumption in aluminium production by about 15%.

Jan 1, 1985

By M Bouare, C Holland, K N’Diaye

Two adjacent open pits in Mali hosted by deeply weathered saprolitic materials were mined consecutively over the course of approximately 12 months. During excavation, both pits experienced significant displacement and tension cracking as the result of deeper than expected depth of weathering coupled with relatively steep slope angles and significant groundwater. In response, geotechnical and operations teams overcame numerous monitoring challenges with prisms and radar to develop a simple and effective monitoring system coupled to a Trigger Action Response Plan (TARP) which enabled continued safe operations while reducing ore loss. Observations of previous slope performance of these two pits allowed for greater confidence in empirical failure runout calculations that was used to specify the standoff widths for the exclusion zones in the pit. Back analysis of the slope as-built performance after the first indications of slope distress was also conducted. The back analysis was used to confirm rock mass parameters for modelling while being utilised as a reality check for the stability analysis. The stability analysis indicated that leaving a large step-out or buttress would not prevent the displacement, resulting in some ore being sacrificed to ensure the safety of personnel. Key learnings from this experience highlight the importance of: • up-to-date geological interpretation of the depth of weathering • ensuring slope design guidance is reviewed and updated as latest information (ie geology and monitoring) is received • having multiple complementary slope monitoring methods to ensure redundancy • ensuring visual observations and as-built performance are utilised as a reality check to provide greater confidence in stability analysis and design guidance.

Jun 22, 2022

By A Moreira, A B. De Souza, S Latchireddi, E Faria

Material transport plays a significant role in the efficiency of horizontal grinding mills - autogenous (AG)/semi-autogenous (SAG)/ball mills. The magnitude of benefits that can be achieved with efficient material transport in AG/SAG mills has been demonstrated in a greenfield milling operation at Mirabela MineratpoÆs SantaRita Nickel operation located in north eastern Bahia in Brazil. This grinding circuit was commissioned in October 2009, was designed as a typical SABC circuit to grind 4.6 Mt/a (575 t/h) to produce a P80 of 125 ¦m with ten to 12 per cent ball charge in the SAG mill. However, it has been operating as an ABC circuit without any grinding media in SAG mill. The nameplate design capacity was achieved in few days and was gradually increased to an average of +800 t/h, still operating in ABC mode. The Santa Rita grinding circuit consists of one 30 ft + 15.4 ft 8.5 MW SAG mill fitted with Outotec patented Turbo Pulp Lifters (TPLÖ) in closed circuit with a HP400 short head pebble crusher and one 20 ft + 28.4 ft 5.5 MW Ball Mill in closed circuit with a Warman cyclone cluster fitted with 10 + 26 in CAVEX cyclones. This paper examines the comminution design process, operating philosophies, experiences, post commissioning optimisation and future development works. Evaluation of the milling circuit performance relative to the design criteria is also discussed.CITATION:De Souza, A B, Latchireddi, S, Moreira, A and Faria, E, 2012. Application of turbo pulp lifter in greenfield operation - Mirabela SantaRita nickel operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 53-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By K Katov, S T. Ciutina, J D. Pyke

The development and optimisation of mill discharge trommels, and specifically their screen panels, can be a neglected area in the complex operation of a minerals processing plant. Trommels are often seen as a ‘set and forget’ component of the circuit, even when significant improvements in design are possible. A redesigned trommel and panel arrangement has simplified and added flexibility to the plant shutdown schedule at Kirkland Lake Gold’s Fosterville Gold Mine in Central Victoria.Prior to the trommel redesign, the shutdown frequency was determined by the expected life of trommel panels at 14 weeks. Planning downtime around this item led to higher maintenance costs and wastage in other areas of the plant. This was particularly disruptive with respect to mill lining change-outs, which were forced out of sequence and often changed prematurely. Fosterville Gold engaged Metso Australia Limited to propose a new trommel design that would better suit the site. The new trommel was engineered to balance simplicity with performance, and incorporated the latest in Modular trommel design, modelling and Finite Elemental Analysis (FEA). Modular Panels and Spiral Segments achieve significantly longer life, and allow in-situ panel change outs, flexibility in spiral and dam positioning and an improvement in classification performance. Trommel panel life has significantly increased from 14 to 71 weeks in the trommel’s highest wearing zone. The new design has eliminated some risks to safety by reducing manual labour and lifting requirements during shutdowns. There is greater flexibility with respect to shutdown requirements. The site is no longer at the mercy of trommel panel lifespan, which allows for better optimisation of wear components in the circuit. CITATION:Pyke, J D, Katov, K and Ciutina, S T, 2018. Modular SAG mill discharge trommel for maintenance flexibility and performance, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Herrmann, J Richards, B Hutchison

An extensive trial of laser-based survey and monitoring systems at Hillgrove Resources Kanmantoo Copper Mine in the Adelaide Hills, South Australia, has proved the capabilities of the system in monitoring rock movements on open pit walls. Initially, the trial involved deploying a Maptek I-Site 8820 laser scanner and the proof-of-concept Maptek Sentry software in the Nugent Pit to monitor ductile rock movements located up to 260 m away. The system was proven to be capable of monitoring various rock movements from 1.5 tonne rockfalls up to a 40 m high toppling wall failure. Data collected from smaller rockfalls was used to help build a database for Hillgrove’s rockfall management program. As part of the trial, the laser scanner was deployed to monitor a ramp movement event, as well as the toppling failure, adjacent to an IBIS slope stability radar. Both devices monitored the slump and the slowly developing toppling movements, with similar results. Although the radar was used as the successful ‘critical alarm’ device for the toppling failure, post-failure analysis showed the laser-based system to be capable of performing a similar role in the ductile rock regime; albeit over much shorter distances than the radar capability. A second laser scanner was deployed to monitor Kanmantoo’s Emily Pit in early December 2014, where it successfully provided critical alarm warnings for a block topple event. Sentry software, which takes advantage of Maptek I-Site 3D spatial imaging technology, was first released in November 2014 to meet industry demand for a cost effective, flexible system to detect movement. Sentry has now been re-launched as a fully transportable monitoring system. Deployed in a custom trailer, the system offers a power and communications module, cellular and Wi-Fi networking and a stable bollard for the I-Site laser scanner and Sentry software. This paper will present rock wall movement data from the Sentry trial and a subsequent two years of monitoring of the open pit walls at the Kanmantoo Copper Mine, at distances out to 750m. In addition, examples of remote geological mapping and small rockfall detection, using the laser scans, will be described. The Sentry system has proven to be beneficial for the continual improvement of slope monitoring and risk management at hard rock mines. CITATION:Hutchison, B, Richards, J, Richards, J and Herrmann, J, 2018. Mine rockfall and rock wall failures – proven digital laser-based approach for monitoring slopes at the Kanmantoo Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 463–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A D. Campbell

The Homer Tunnel is located in a remote area of the South Island of New Zealand and carries large numbers of tourists to Milford Sound through an avalanche prone area. The tunnel is 1280 m long with a steep ten per cent unidirectional grade descending to the west. Construction of the tunnel began in the 1930s and was completed to a nominal 6 m width in 1954. In 1996, two passing bays were stripped-out to accommodate bi-directional flow of tourist coaches. During all phases of construction and widening there have been episodes of strain bursting.The condition of the tunnel and standard of internal services is below current international practice, principally in terms of; in-tunnel air quality, fire life safety, ground support, and road safety. A number of near-miss events have occurred involving coach fires on the approaches and inside the tunnel. The national road authority, NZTA, is considering a substantial investment to improve amenity and safety of the tunnel.This paper describes the rationale for the proposed upgrade works and the investigations undertaken to enable that design. A holistic approach to road tunnel safety has been adopted that balances the key interrelated safety drivers, namely; tunnel lining, traffic operations, ventilation, power supply and egress while ensuring continuity of safe access to Milford Sound.

Mar 8, 2011

By R Tooher, S J. Oliver

The operation of copper flotation circuit is a challenging task for the site metallurgists and plant operators. To optimise the performance requires meeting both grade and recovery objectives. These plants have numerous pieces of equipment that are monitored by hundreds of sensors. The challenge is to review these sensors and adjust the numerous control inputs to maintain peak operational efficiency for extended periods. There is also a need to respond to equipment failure. These challenges lead to in operational inefficiencies and can result in a reduction in revenue.This paper details an overview of an operational assistance tool implemented at Newcrest's Telfer plant’s copper flotation circuit. This tool is based on a digital twin of the plant. A digital twin is a model of the plant that is simulated in parallel to the normal plant operation. It is fed with the plant data in real time to provide a prediction of plant operation. The model outputs directly generate the metrics that are used to assess the plant performance, and these are compared with the metrics calculated from the actual plant’s operation. Deviations between the model estimate and the plant’s actual performance are used to gather insight into plant health and alert the operator to poor performance. The operators gather more information regarding the root cause by reviewing the model’s inputs that have deviated outside their normal operating range. An evaluation of the plant performance, following the commissioning of the digital twin, showed an overall reduction of acid soluble copper in the tails.This paper discusses the implementation of a digital twin of the plant to monitor plant performance during live operation. It will include details on data collection and cleansing, data reduction techniques, model development, and real-time implementation. The results of the case study of an implementation of a digital twin at Newcrest's Telfer copper flotation plant will be used throughout the paper.CITATION:Oliver, S J and Tooher, R, 2018. Optimising flotation plant operation by using a digital twin in the control room, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 93–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Oda Y, Hashiuchi M

In the smelting section, flexible fuels such as coal or coke are used in place of heavy fuel oil in order to utilize energy sources more efficiently. Heat recovered from the off gas of the furnace has been converted by the waste heat boiler into steam, which is used for self power generation and for heating or maintaining various temperatures. The amount of the recovered steam in the smelter is currently increasing due to maximum utilization of powdered cokes. The heat source required to maintain the temperature of the electrolyte in the tank house is electric power and steam. However until recent year this steam was provided by its own heavy oil combustion type boiler in the tank house since the amount of steam consumed in heating the electrolyte is large. Though experimental work over the last few years has shown the advantages of reducing steam in the tank house by fully covering the cell, the implementation of the full cover can lead to other operating problems. However various improvements, mainly the covering of the cell with a simple device, have led to greatly reduced steam consumption. As a result, steam for the tank house is now provided by the waste heat boiler only bringing more efficient energy usage.

Jan 1, 1987

CONTENTSThe significance of values givenINTRODUCTIONTHE ORE1. DATA SECURED FROM THE MILLING PLANT AS OPERATING BETWEEN 1938 AND 1942(a) Mill Recoveries(b) Mill Flow Sheet(c) Scheelite-Garnet Association(d) Detailed Examination of Mill Performance during 1942Crushing UnitsCoarse Rolls DischargeFine Rolls DischargeFeed to Huntington MillsFinal Ground ProductProduction of -200-mesh Scheelite SlimeSummary of Information on Crushing and Grinding Circuit(e) Detailed Examination of Mill Performance During 1942Concentrating UnitsLocation and Nature of Scheelite LossesSize Distribution of Scheelite LossesDistributor Spigot ProductsSummary of Information on Concentration Circuit(f) Detailed Examination of Mill Performance During 1942 Gravity Plant Feed2. EXAMINATION OF MINE SAMPLES TAKEN DURING 1942(a) Introduction(b) Nature of the Ore(c) Sampling of Mill Feed(d) Testing Technique(e) Minus 1/8-inch Ores-Naturally Broken Fractions(f) Recoveries from Plus 1/8-inch Fractions-Crushed to Minus 1/8-lnch(g) Probable Recoveries Obtainable from Weathered Ores140 Contour120 Contour90 Contour(h) Examination of an Ore Sample from the 90-foot Adit(i) Run-of-Mine Ore(j) Evidence of Maximum Sizes of Scheelfte Present in Run-of- Mine Ore(k) Summary of Information on Liberation and Recovery from the Ores as Mined in 1942 and from the Mill Samples

Jan 1, 1944

Traditionally, the development of a mineral resource project goes through a fairly set pattern of decisions from what commodities to search for; where to look; how to locate; what are the reserves; how can they be exploited with optimum returns for all stakeholders; where are the markets and what will be the price received; what financing arrangments? However, due to the unique nature of most mineral resource properties, the relative significance of individual parameters on the ultimate development decision will vary from project to project. Sensitivity analysis in its formal sense is most frequently related to the economic analysis of a project particularly in conjunction with the ultimate development decision making process, and acknowledges the uncertainty of the actual values with their impact on the corporate decision making yardsticks. In many cases, this analysis merely adds more values to confuse the decision makers who may well opt for some subjective rationale to overcome the numeric confusion. However, sensitivity analysis should be used more frequently to exploit the development dollar to its maximum, THROUGHOUT the phases leading to the development decision. It is essential to identify the critical inputs to the various decision tiers in a project as early as possible and direct the funds to ensure that these parameters are determined as accurately as possible. Examples are used to illustrate the need for an even-handed quantification of the parameters which affect the outcome of decisions en route to the final one while minimising the risk in making an optimum assessment in relation to development funds Available.

Jan 1, 1983

By D L. Head

Critical risk management (CRM) has become one of the latest safety buzz terms in mining. Everyone seems to be doing it, everyone seems to know about it, yet we are still having fatalities in our industry from well understood hazards such as mobile equipment amongst others.

May 5, 2022

The Yanacocha district hosts the largest and most significant acid-sulphate, high-sulphidation deposits in Per· with total production, reserves and resources of over 27 million ounces of gold. Several other smaller high-sulphidation systems are also recognised in the Cajamarca region including La Zanja, Sipßn, Tantahuatay, and San Nicolas. These each have reserves/resources of between 640 000 and 800 000 ounces of gold. Gold deposits in the Yanacocha district are hosted in an extensive volcanic field. Flow domes have intruded precursor pyroclastic rocks and flows that are interpreted as part of an earlier intermediate multi-vent volcanic complex. The larger, contiguous Yanacocha Norte - Sur and Encajon gold deposits are spatially associated with late-stage diatreme breccias. At La Zanja extensive acid-sulphate alteration is associated with the margins of the small San Pedro caldera (6 +4.5 km), nested within the larger, less well-defined La Zanja caldera (19 +24 km). The inner caldera is resurgent with abundant magmatism expressed as several flow dome complexes located on the caldera rim, and shallow level intrusive stocks. Gold mineralisation is associated with a WNW-trending structural corridor that transects the southern margin of the San Pedro caldera. On the eastern side of the La Zanja caldera there are a series of younger andesitic eruptive centres, some associated with acid-sulphate alteration and gold mineralisation. The Sipßn deposit occurs in one such centre with structurally-controlled gold associated with a NE-trending silicified structure developed within a sequence of andesitic tuffs. In conclusion, although a number of high-sulphidation deposits are recognised in northern Per·, their settings and styles of mineralisation are all quite different. Smaller deposits generally have strong and obvious structural controls. In the larger Yanacocha deposits the structural controls are less obvious, and mineralisation is disseminated in porous or strongly fractured and brecciated silica. Erosional levels are probably a significant factor, with disseminated mineralisation at higher levels, and structurally-controlled mineralisation in more deeply eroded deposits.

Jan 1, 1999

Xstrata CopperÆs Mount Isa Copper Operations is located in mineral rich north-west Queensland and is one of the largest sources of copper in the world. This world-class underground operation is planned to produce over 6.6 million tonnes of copper ore in 2007 from the X41 and Enterprise Mines. With an underground mining history of over 50 years and underground reserves of over 83 million tonnes at 2.6 per cent copper, mine planning for the future becomes an exciting challenge for the technical team due to the older nature of certain areas. The 1100 Orebody of the X41 mine was one of the first places that copper mining occurred, with its discovery in 1953 - 1954 and mining commencing in the 1960s. Sublevel open stoping mining methods have been employed since that time as the means of extraction, using a primary-secondary sequence to maximise stope turnaround time. Large Transverse Pillars within the 1100 orebody were not mined out in order to provide access for ventilation, power, orepasses and other services. The Panel Pillar, 4180XC and 4010XC pillars are three such Transverse Pillars in the 1100 orebody that will be mined as a final retreat. This paper discusses the technical challenges and issues associated with the extraction of Q390 stope, one of the stopes located in the Panel Pillar, and the design solutions to overcome these issues. Managing the exposure of backfilled stopes of variable fill strength, ensuring the stability of the crown, stope walls and drawpoints, managing vertical openings, re-establishing service networks, and stope filling are the critical issues given consideration for the final design of Q390 stope and other such stopes within a Transverse Pillar. Communication and coordination between the different departments in the mine are essential for the necessary work to be completed in a timely manner to bring pillar stopes into production.

Jan 1, 2007

By Dods G. H, Hewitt W. V

Ashton Mining Limited is currently one of the active companies undertaking gold exploration in Indonesia. Presently 7 Contract of Work areas are being explored for hard rock and alluvial gold. Hard rock exploration is focussed on the Tertiary volcanic arc terrains in which a variety of epithermal mineralisation styles have been identified. At the regional stage remote sensing techniques using Landsat, Spot and SLAR imagery where available, and photogeological studies are carried out in parallel with regional reconnaissance fieldwork programmes. These involve geological mapping and geochemical drainage sampling. Remote sensing techniques have proven useful in both the extrapolation of known geology and the identification of tectonically favourable settings as controls to mineralisation and volcanicity. The variety of mineralisation styles and settings is reflected in the highly variable geochemical signatures encountered. This has necessitated the refinement of sampling methods and sample preparation techniques for pan concentrate, stream sediment and soil samples in specific project areas. At the detailed prospect stage, mapping with particular attention to structural controls, wallrock alteration assemblages identified by petrog- raphy and XRD clay mineralogy, have proved useful in focussing drill targets. Drilling to date has utilised conventional diamond core drilling methods, the use of lightweight, man-portable "Winkie"-type rigs and hammer auger bedrock sampling systems. Geophysics methods successfully employed on various projects have included airborne magnetics and radiometrics, detailed ground magnetic surveys, VLF-EM and SIROTEM.

Jan 1, 1991

By Sharmil Markar M

Ballarat Goldfields Limited is currently re-opening the old workings of the East Ballarat Goldfield which contain an estimated 1800 ML of groundwater. The disposal of this 'minewater' was of concern: the minewater is of moderate salinity; increased salinity levels have interfered with agriculture and water use at a number of locations downstream from Ballarat. Extensive numerical studies indicated that treated minewater could be discharged into the Ballarat Creek system for dilution by sewage effluent and by surface runoff after rainfall events. An automatic real-time salinity management system has been developed to enable the disposal of saline minewater in this fashion. A desk top computer operates the system: discharge and salinity readings are taken automatically each hour and filed away; the maximum allowable rate of discharge of treated minewater is calculated; pumps are switched on and off. The system readily enables daily, weekly and monthly data reports together with floppy disks of 'raw' data to be prepared in formats suitable for direct submission to the Victorian Environmental Protection Authority.

Jan 1, 1990