Search Documents

By J. D. Raulerson, J. M. Williams

This paper presents a comparative evaluation of several system currently being used or proposed for the transport of matrix from an open-pit mine to a large fixed plant. The matrix is a sticky, wet clay to be carried from 8-16 km (3-10 miles) at 910 t/h to 1.8 kt /h (1,008-2,000 stph). The system is complicated by frequent moves of the open-pit mine site and other factors, such as use of the clay component in land reclamation.

Jan 1, 1984

By R. W. Heckel, R. L. DeGregorio

The DeHoff method of determining the size distribution of ellipsoid-shaped, second-phase particles has been applied to the spheroidization of cementite in a eutectoid steel. The surface area of Precipitates determined from the various size fractions in the distribution was correlated with surface-area measurements based on the number of intersected interfaces on a random lest line. The precipitate particles were found to be oblate ellipsoids with an axial ratio of about 0.90. The size distributions were found to be log-normal. A method is proposed whereby the shrinkage of small particles and growth of large ones can be determined from the experimental data. The experimental data are compared to previously proposed mathematical models describing diffusion-controlled kinetics and various types of interface-controlled kinetics. The experimental growth and shrinkage rates are considerably slower than those predicted by diffusion-controlled kinetics. The best fit is obtained for a model describing interface-controlled kinetics limited by the rate of formation of cementite at the growing interfaces where the interfacial reaction rate is proportional to the solute thermodynamic activity gradient across the surface. THE subject of spheroidization of second-phase particles has been considered previously by other investigators. Livingston1 has studied the precipitation of the cobalt-rich phase from copper alloys containing 0.7 to 3.2 wt pet Co. His results indicate that the average particle size increases as the cube root of the heat treatment time in accord with diffusion-controlled kinetics.'-' Komatsu and rant' in their studies of the growth of SiO2 in a dispersion-strengthened copper-silica alloy found that the initial growth of SiO2 proceeded by diffusion-controlled growth and later stages were limited by interface-controlled growth. The values of the activation energy obtained for the interface- controlled process led them to the conclusion that the process was limited by the dissociation of SiO2 at the shrinking interface. The transition from diffusion-controlled growth to interface-controlled growth was characterized by a particle size which varied with the heat-treatment temperature. It is also interesting to note that the particle-size distribution as found by Komatsu and Grant exhibits log-normal behavior when replotted on log-probability coordinates. Dromsky, Lenel, and Ansell9 have observed the growth of Al2O3 particles having a mean free path of about 1.5 to 13 µ. Their photomicrographs indicate that the Al2O3 particle sizes were larger than those observed by Komatsu and Grant. Dromsky, Lenel, and Ansell concluded that the Al2O3 coarsened by an interface-controlled growth mechanism limited by the solution of A12O3 at the shrinking interfaces. Bannyh, Modin, and Modin10 have studied the spheroidization of a eutectoid steel (0.83 wt pet C). Their spheroidization (tempering) treatments were carried out in the range from 210o to 700°C for times between 1.5 sec and 20 hr. Measurements of mean particle size as a function of time indicated a cube root of time dependence of size at 700°C, in agreement with previous analyses of diffusion-controlled kinetics.2°7 At lower temperatures, the time dependence was less than the one-third power. It is important to note that, although mathematical models of growth* considering particle-size distribution have been available, measurements of only mean particle size have been carried out. DeHoff11 has presented a quantitative metallography technique which is applicable to the determination of the size distribution of ellipsoids of constant shape. This method is applicable to both oblate and prolate ellipsoids of all ratios of minor to major axis and is based upon an extension of Saltykov's analysis12 of the distribution of spheres of varying size. DeHoff's analysis is based upon measurements of the minor axis of the particles on a random plane of polish in a unit area. This method provides a measure of the number of ellipsoids in various size ranges per unit area. As pointed out by DeHoff, such measurements may be used to obtain surface area and total precipitate volume data. Thus, the accuracy of the distribution analysis may be checked by comparison of the surface and volume

Jan 1, 1965

By R. V. Whetsel, V. R. Garfias

For some time the writers have been compiling and analyzing statistics of consumption and production of petroleum, its products and related fuels, in order to arrive at a fairly accurate picture of the world-wide situation of the petroleum industry. In production, crude oil, natural gasoline, benzol and alcohol blended with motor fuel have been considered. In consumption not only refined products, but crude consumed as fuel, refinery losses, ships' bunkers and blended fuels have been taken into account to obtain a true balance between supply and demand. Statistics from practically every country and territory have been studied, and where actual figures were not available the estimates have been based on all the data available. The figures in Table 1 indicate that during the last five years the world's production has exceeded demand every year and that the aggregate difference is some 207,150,000 bbl. The supply in the United States exceeded consumption by 111,401,000 bbl. over the same five-year period and in 1931 and 1932 the demand exceeded supply, while outside the United States the excess of output over demand was 95,749,000 bbl. Table 2 combines the excess production in the United States with its favorable balance of exports over imports, showing that the United States has reduced its storage over the five years by about 136,-595,000 bbl., while in Table 3 it is shown that, including its excess of imports from the United States, the rest of the world has added 343,-745,000 bbl. to storage during the period in question, the greatest accumulation coming in 1934. Table 4 shows the world's consumption classified by countries according to the principal products. These tables also indicate that at the end of 1934 the statistical position of the petroleum industry outside the United States was decidedly unstable, a situation that probably will become more acute as a result of the added Iraq production; and that the present favorable statistical position of the industry in the United States, which is partly due to the excess of exports over imports, may be to some extent jeopardized by the unstable situation in the foreign market.

Jan 1, 1935

By AIME AIME

ONE unique distinction can be claimed by the new Chairman of the Coal Division, C. E. Lawall: he is the only A.I.M.E. member also a university president, though several engineering colleges are headed by Institute members. Only last year he was promoted from director of the school of mines to president of West Virginia University, following a term as acting head of that institution of over 3000 students. He was born in Catasauqua, in eastern Pennsylvania, on Nov. 21, 1891, and went to Lehigh, receiving an E.M. in 1914, and an M.S. seven years later. His engineering career began in the Pittsburgh Testing Laboratories. After three years there he came to Palmerton for

Jan 1, 1940

In accordance with the provision of the Constitution, notice is here given to all Members, Associates, and Junior Members, that the dues of the year 1918 will be payable on Jan. 1, 1918, at the office of the Secretary. The dues for Members and Associates are $12 per year and the sum of $3 additional is asked of those Members and Associates who desire to have the three volumes bound in the Institute's standard half-morocco binding. The dues of Junior Members are $5 per year.

Jan 1, 1918

By Frank E. Caropreso, William P. Badger

A hydrogen peroxide precipitate process has been adopted by Atlas Minerals for the recovery of uranium oxides from sodium chloride strip solutions. Adoption of the process was based on laboratory and plant tests comparing hydrogen peroxide with other precipitants. Plant operation has demonstrated that the hydrogen peroxide process consistently yields uranium concentrates of high purity and barrens of low uranium content. Increased U3O8 concentration in the product, reduced levels of impurities which incur penalties, and higher product density have produced economic advantages.

Jan 1, 1974

The Institute of Metals Division and the American Foundrymen's Association will meet in Philadelphia Sept. 29 to Oct. 4. Many things of interest to the members of the Institute have been constructed and developed in the Philadelphia district since the last meeting in that city (1907), including the great plant at Hog Island, the new foundries at the League Island Navy Yard and the great foundries of the Westing-house Company at Essington. Invitations are being extended to foundrymen and industrial engineers generally in. England, France, Belgium, Italy, and other European countries, South American countries and Australia, to attend this convention, since the time. seems unusually opportune for holding a meeting of international scope.

Jan 5, 1919

By Howard N. Eavenson

The mines of the United States Coal & Coke Co. are located in the Pocahontas coal field, in McDowell County, West Virginia. Twelve plants have been opened and equipped, of which, by reason of the present business depression, only nine are now in operation. These twelve plants serve eighteen mines; some of the plants having several openings, in either the same seam or in different seams, tributary to the same tipple. Only nine of these mines are now being worked at the plants in operation. Construction work was begun in 1902, and coal from the first three plants started was shipped in December of that year. An additional plant was opened in 1903, two in 1904, two in 1905, two in 1907 and the last two in 1908. On Jan. 1, 1915, the plants have been in operation an average period of 8.8 years. The rules of the company, which have been in operation since work was first begun, are similar to those in use by the H. C. Frick Coke Co. at its mines in Pennsylvania, in which " Safety First" was incorporated as early as 1907; and it has always been the policy of both companies to look carefully after the safety of their employees. Although the field is an extension of the old Pocahontas field, the mines, located upon a new branch railroad, are away by themselves, and, as is usual in such cases, the class of labor attracted at first was temporary in character. The rapid development of the mines required the employment of many new men and officials each year; and, while the accident record from 1904 to 1909 was as good as the average of the field, it was felt to be not as good as it could be made, and a determined campaign was inaugurated for preventing accidents of all kinds. Fig. 1 shows the tonnage of coal produced per fatality, both total and for inside accidents only, at our mines; the tonnage per fatality of all West Virginia mines, and of those in the Pocahontas field. The purpose of this paper is not one of congratulation on the results so far accomplished, since the operating officials are not at all satisfied that the maximum is in sight, to say nothing of its having been reached; but to describe the organization and methods that have produced these

Jan 1, 1915

By C. A. Siebert, G. Sandoz

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By G. Sandoz, C. A. Siebert

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By G. R. Belton, Y. K. Rao

A galvanic cell, using liquid MgCl2 or MgC12-CaC12 mixtures as the electrolyte, has been used to determine activities in Mg-A1 liquid alloys between 700' and 880°C. The incovporation of a chlorine electrode in the cell also allowed measurements to be made of the standard free energy of formation of MgCl2(l). The results are shown to be in good agreement with thermo-chetrlical values from the literature, and this is taken as evidence that the small, known solubility of magnesium in iMgCl2 introduces no significant error in galcanic cell measurements. Within experimental error, the activity coefficients and relative partial molar enthalpies at 800°C are shown to be represented by the following "subregular" solution equations: logy~~ =-0.68(1 -xMgj3 log yAL =-1.02(1 - XMf + 0.68(1 - XMf H.M = -4400(1 - %)3 / cal Mg 7Ag' HZ =-6600(1 - xA1)' + 4400(1 - XMf cal SCHNEIDER and toll' have used a transpiration technique to measure the vapor pressures of magnesium over Mg-A1 alloys between 544" and 594°C. amsstad,' however, has since suggested that the extrapolation to zero flow rate, used by these authors in interpreting their apparent pressure vs flow rate data, gives unreliable results. Rogers, Tomlinson, and Richardson,3 in interpreting the results of solution equilibria between Mg-A1 alloys and liquid MgC12, also considered the measurements of Schneider and Stoll to be unreliable and preferred to derive activities for the alloys from the earlier boiling point determinations of ~eit~ebel~ and the partial molar heats recommended by Kubaschewski and ~atterall.~ These latter heats were based substantially on the early calorimetric work of Kawa-kami but, unfortunately, his work on other systems has sometimes been found to be inaccurate.7 Rogers et al., in the above-mentioned paper,3 tentatively concluded that the most likely species responsible for the limited solubility (0.3 mole pct at 800°C) of magnesium in MgC12 were Mg° (neutral) and Mg2++. Two more recent studies8,9 have supported Mg2++ as the soluble species. In the present study, activities in Mg-A1 alloys have been determined by means of a galvanic cell involving liquid MgCl2 or MgC12CaCl, mixtures as the electrolyte. Since the reactive nature of magnesium precluded simple Faraday yield experiments, a chlorine electrode was incorporated in the cell in order that the performance of the cell could be checked by measurements of the heat and free energy of formation of MgC12. This procedure was considered necessary since it has been suggested1' that the solubility of a metal in a molten salt might introduce electronic conductivity; also, previous determinations of the standard electrode potential for MgC12 differed by as much as 70 mv11-13 EXPERIMENTAL Materials. Analyses of the materials used in preparing the alloys and the electrolyte mixtures are presented in Table I. The alloys were prepared by induction melting weighed amounts of the metals in a graphite crucible held under an argon atmosphere. Pure anhydrous magnesium chloride was prepared by heating the mixture MgCl, . 6H20 +NH4C1(1:1) to 650°C, followed by melting under dry argon. The melting point of the dry MgC12 was found by differential thermal analysis to be 714.8oC, which compares well with the accepted value of 714C.14 This agreement was taken to be an indication of the high purity of the dried salt. Table I. Compositions of Materials, wt pn Impurity Mg Al MgCI2 CaCI, Ba - - 0.005 Ca - - 0.010 Cu 0.02 0.02 Fe - 0.10 0.001 0.010 Pb 0.01 - 0.001 0.005 Mn 0.15 0.001 Si - 0.10 Sr - - 0.005 MBSO* - 0.040 ARGON TUNGSTEN CHLORINE LEAD—411 11 II ALUMINA 'A I / ave GRAPHITE on irA~_ ( ^"l ROD MAGNESIUM S>ILICA~^ /, OR ALLOY-. I /A] ___________ -«^- _ ELECTROLYTE I y FRITTED DISCS Fig. l—Arrangement of chlorine and metal electrodes in electrolytic cell.

Jan 1, 1970

By M. B. Bever, A. M. Reti, A. K. Jena

The results of this investigation show that in the system SnTe-PbTe l) the solid solutions have small exothermic heats of formation relative to the binary compounds, 2) solid-solution hardening is almost absent, 3) the tin and lead atoms are .randomly distributed on the sublattice occupied by them and do not undergo an ordering transition during a thermal treatment designed to promote such a transition, and 4) the lattice parameter changes linearly with composition. These findings suggest that the solid solutions of tin telluride and lead telluride approach ideal behavior. THE binary compounds SnTe and PbTe form a continuous series of solid solutions.' Information on several physical properties of these solid-solution alloys has been published.1"3 In the work reported here, the heats of formation, microhardness, and lattice parameters of these alloys have been measured and the possibility of an order-disorder transition has been investigated. Order-disorder transitions occur in some solid solutions of binary compounds. In the system Bi2Te3-BizSes, for example, the electropositive bismuth atoms and the electronegative tellurium and selenium atoms always occupy separate layers. In the disordered alloy Bi2Te2Se, the tellurium and selenium atoms are randomly distributed on the layers occupied by them, while in the ordered alloy they occupy distinct layers.4 The NaC1-type (Bl) structure of SnTe-PbTe alloys consists of two sublattices, one of which is occupied by the electropositive tin and lead atoms and the other by the electronegative tellurium atoms; any ordering would be expected to occur in the sublattice occupied by the tin and lead atoms. PREPARATION OF SPECIMENS Polycrystalline specimens of PbTe and Sn1-xPbxTe (x = 0.25, 0.50, and 0.75) were prepared by melting stoichiometric amounts of lead (99.999 pct), tin (99.98 pct), and tellurium (99.999 pct) in evacuated and sealed Vycor tubes. Because of the deviation of tin telluride from the stoichiometric composition5 this compound was prepared by melting 49.8 at. pct Sn and 50.2 pct Te. The tubes containing the melts were quenched into water; the solidified ingots were removed from the tubes and annealed for 2 weeks in vacuum (PbTe approximately 100°C below its melting point, the three alloys 100°C below their solidus tem-

Jan 1, 1969

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By H. C. Casey, M. B. Panish

The roles of the phase diagram and the diffusion and solubility analyses in the selection of sources for the diffusion of zinc into GaAs are discussed. Isothermal sections of- the phase diagram are described at 1000°, 775°, 744°, and 700°. Below 744° the three solid phases, Zn3As2, GaAs, and ZnAsz, may be in equilibrium. In the composition regions where the three solid phases are in equilibrium, the partial pressures of the components do not vary with composition and there is no liquid phase. A diffusion source composition within that region containing 5, 50, and 45 at. pct Ga, As, and Zn was selected to yield reproducible diffusion profiles without surface damage. The 5/50/45 ternary source Provides a significant improvement in the reproducibility and planarity of- the zinc diffusion as compared with other zinc diffusion sources that result from starting with elemental zinc, dilute solutions of zinc in gallium, or various combinations of zinc and arsenic. Several experimental diffision profiles for the 5/50/45 diffusion source have been determined. The profiles are very steep in the region of the junction and produce devices that exhibit step junction behavior. The junction depth varies as the square root of time. Diffusion at 700°C for 4 hr gives a 5-µ junction depth and a surface concentration of 2.4 x1020 cm-3. The surface concentration is enhanced by a factor of three and the junction depth decreased by a factor of ten as compared with diffusion with a starting source 01- elemental zinc. The differences in dijyusion behavior with these two sources are due primarily to the approximately 10' greater equilibrium As4 partial pressure for the 5/50/45 source. ThE most common technique for the preparation of GaAs p-n junctions for diverse applications ranging from switching diodes to injection lasers has been to diffuse zinc into the solid from the vapor phase. The zinc impurity has generally been provided by introducing into a diffusion ampoule elemental zinc, dilute solutions of zinc in gallium, or various combinations of zinc and arsenic. For the purpose of eliminating surface deterioration, zinc has been diffused into GaAs through SiO2 films1 and from zinc-doped SiO2 films.2 During a study of the injection and recombination mechanisms in GaAs junctions, we found that these diffusion techniques either resulted in nonreproducible diffusion profiles and nonplanar junction interfaces or were extremely inconvenient to use. An unpublished report by Allen and pearson3 emphasized that an understanding of diffusion requires relating the diffusion conditions and system compositions to the ternary phase diagram. Recent studies have made it possible to relate the effect of starting source composition on the GaAs sample surface and diffusion profile reproducibility and, in addition, to estimate the expected surface concentration and zinc diffusivity. These studies include the Ga-As-Zn phase diagram,415 the determination of the incorporation reaction for zinc as a substitutional impurity,6 and the analysis of the concentration dependence of the diffusion coefficient.' In this paper the role of the phase diagram in the selection of the starting diffusion source composition is illustrated, and an application of the diffusion and solubility analyses is used to demonstrate their utility in the estimation of surface concentration and diffusivity for various starting source compositions. Consideration of the isothermal sections of the ternary phase diagram shows that below about 744° C a composition region exists where the three solid phases Zn3As2, GaAs, and ZnAs2 are in equilibrium without a liquid phase. In this region the partial pressures of the components do not vary with composition, and thus the surface concentration and diffusivity depend only on temperature. A diffusion source composition within that region containing 5, 50, and 45 at. pct Ga, As, and Zn was selected. As will be described in detail, this diffusion source yields reproducible diffusion profiles without surface damage, planar junction interfaces, and steep profiles that result in devices with step junction behavior. Only closed diffusion systems are considered. Open or flowing vapor systems require the maintaining of constant vapor pressures in the flowing gas and represent control problems outside the scope of this discussion.

Jan 1, 1969

By W. Jolley

Decarburized iron and Fe-3.28 pct Ni alloys were impact and tension tested in the temperature range of ambient to 4°K. It was found that alloying with nickel improves the fracture properties of the ferrite matrix. The improvement in toughness of iron alloyed with nickel is attributed to the effect of the nickel addition on the temperature and strain rate dependence of the yield stress as well as on slip behavior. The Fe-Ni alloy exhibits wavy slip when strained at temperatures down to at least 50°K. This behavior contrasts with that of the unalloyed iron where a change It is a generally accepted fact that of the common alloying elements of steel only nickel and manganese improve both the room-temperature yield strength and the notch impact properties. It has been argued for a number of years that manganese refines the ferrite grain size, the pearlite spacing, and the grain boundary carbides in medium- and low-carbon steels and thereby increases resistance to brittle fracture.''' This hypothesis recently was confirmed for a 0.04 pct C iron containing manganese, but at the same time from wavy to planar slip occurs at about 120°K. The observed lower temperature and strain rate dependence of the lower yield stress in the Fe-Ni alloy as compared to the unalloyed iron may be attributed to this difference in slip behavior. In contrast to suggestions published previously, transmission electron microscopy showed that the uniform dislocation distributions and the lack of dislocation tangles which are produced by low-temperature straining of bcc materials cannot be attributed to the absence of cross slip at these temperatures. no increase in notch toughness was observed in a decarburized Fe-Mn alloy.3 It thus appears that manganese only increases the toughness of Fe-Mn-C alloys by refining grain boundary carbides and has no toughening effect in carbon-free iron. On the other hand, the mechanism whereby nickel improves toughness has not been established. Hodge et a1.4 have clearly shown that a 3.28 pct Ni addition lowers the impact transition temperature of 0.02 pct C steel approximately 35°C when the grain size is maintained constant. Recently, Wullaert and Tetelman6 stated that nickel refined the grain boundary carbides of an Fe-C alloy and consequently increased the toughness. They also observed the previously reporteda-'

Jan 1, 1969

By L. Stone, H. Margolin

The Ti-C-N and Ti-C-O systems were investigated in the temperature range from 500° to 1400°C and in the composition range up to 2 pct C and 5 pct N or 0. Characteristic isothermal sections at 800°, 900°, 1000°, and 1300°C are presented. The Ti-N-0 system was studied in the temperature range from 900' to 1400°C with alloys containing up to 6 pct total alloying content. Characteristic isothermal sections at 1000° and 140O°C are presented. Melting-point data for all three systems are also included. THIS paper reports on one of a series of investi-gations which have been conducted on the phase diagrams resulting from interstitial alloying with iodide titanium. The other investigations involved delineation of the binary systems with carbon,' nitrogen and boron,h and oxygen. The Ti-0 binary system has also been investigated by Bumps et al.' In varying degrees, each of these interstitial elements has been shown to stabilize the low temperature a modification of titanium1-5 and each forms a face-centered cubic TiX compound (henceforth designated 6). In addition, the Ti-N and Ti-0 systems reveal a low temperature tetragonal phase (6) formed by a peritectoid reaction between a and TiX Experimental Procedure The development of experimental techniques for the study of titanium alloy systems has, to a large extent, become standardized. In this investigation, the equipment and procedures described in detail by Cadoff and Nielsenl have been used. Arc Melting: In general, binary alloys with carbon, nitrogen, and oxygen, prepared in the composition range of interest in this investigation, show negligible composition changes during arc melting. However, the possibility of the formation of some gaseous combination of alloying elements such as CO, CN, or NO during the preparation of these ternary alloys was considered. Calculations showed that the evolution of only 0.05 gram of such a gas would be detectable as a pressure change in the closed system used during preparation of these alloys. Such pressure changes were not observed. Consequently, nominal compositions have been used in plotting the data. The compositions of the materials used in the preparation of the alloys are shown in Table I. After melting for 3 to 5 min at 275 to 350 amp, the alloys were checked for homogeneity by microstruc-tural examination. Alloys containing up to 1 pct C were homogeneous in the presence of less than 3 pct N or 0. At higher alloying contents, some inhomo-geneities in the carbon distribution became evident. Alteration of the melting procedure toward longer times and higher currents did not improve the homogeneity of these alloys. Ti-N-0 alloys were homogeneous in the range to about 3 or 4 pct total alloying addition. Beyond this, almost all of the specimens showed as-cast microstructures consisting only of the phase. Consequently, inhomogene-ities could not be detected by examination of micro-structures. Ten alloys from each of the systems were analyzed for two of the elements present (oxygen being omitted in all cases and titanium being omitted in the Ti-C-N alloys). In all cases the analyses were found not to be sufficiently precise to serve as criteria for the total composition of these alloys. On the basis of phase distribution in heat-treated alloys, however, it appears that carbon is distributed throughout the alloys most uniformly, with oxygen and nitrogen following in that order. Heat Treatment: Specimens for heat treatment were wrapped in titanium sheet before sealing in the argon-filled quartz capsules. Heat-treatment times varied from 100 hr at 800°C to 0.5 hr at 1400 °C. After heat treatment the specimens were quenched by breaking the capsule in water. With the exception of alloys in the low composition region, heat treatment did not have an appreciable effect on the as-cast microstructures. Metallography: Following heat treatment, the specimens were prepared for metallographic examination by grinding on emery paper and electrolytic polishing. For the majority of the specimens a 10-sec etch with Remington "A" agent (25 pct HNO3, 25 pct Hf, and 50 pct glycerin) adequately

Jan 1, 1954

By Louise Barton Freeman, Iley B. Browning, Coleman D. Hunter

During 1942, production of oil in Kentucky reached a total of 4,169,163 bbl. of which 1,807,809 bbl. came from eastern Kentucky. This was more than a million barrels less than in 1941, owing partly to the low price of crude oil, which almost eliminated wildcatting, and partly to spacing regulations, which limited the number of wells drilled in small, shallow pools where the pressures are not sufficient to maintain maximum recovery in widely spaced wells. In eastern Kentucky much of the oil was produced from outliers of the Mauch Chunk series at the disconformable contact of the Mississippian and Pennsylvanian. Although wells producing from this horizon, known as the Maxon, are sprinkled over the entire area, the greatest concentrations are in Martin, Floyd, Knott and Pike Counties. A new 30 to 40-bbl. well has been completed in this formation in ,Pike County, where the carbon ratio is so high that ordinarily oil would not be expected. Pike County is one of the largest producers of Maxon gas, and the offset well to this oil well produced gas. Of the 412 gas wells drilled in Pike County, 12.2 per cent produced gas from the Maxon horizon. During 1942, the old Menifee " Cornif-erous" field, the Mariba-Denniston field, was redrilled between old wells, and although it did not produce any large amount of oil it did contribute 2018 bbl. In the oldest oil field in eastern Kentucky, the Ragland pool, operators are cleaning out abandoned wells and are using this oil for fuel oil. There is a possibility that some of this may be used in the future as distilled fuel oil. Eight wells were completed in 1942 in the Jackson County gas field. The development of Jackson County, which was started in 1934 and in which commercial quantities of gas were encountered at a depth of 1100 to 1200 ft., has become of importance in 1942 with the completion of eight wells, making a total of 24 commercial producing wells with an average rock pressure of 140 lb. At this time the gas is not being marketed. In the last year it has been found that these wells, which produce from the Niagaran dolomite ("Cornif-erous"), respond to acidizing and the production has been thus greatly increased. There has been less development in Estill and Lee Counties than for several years. Two wells were drilled in Greenup County, one of which had a show of oil in the Berea sandstone. One deep test, drilled by the Owens-Libbey-Owens Co. in Lawrence County, was dry. This well was drilled to a depth of 4975 ft. into the top of the Clinton shale sequence. Of the 202 wells completed in Floyd, Martin, Knott and Pike Counties, 187 were gas wells, 3 oil wells and 12 dry holes. In Floyd County 66 per cent of the gas production was from the Devonian-Mis-sissippian black shales, 53 per cent in Martin, 79 per cent in Knott and 65 per cent in Pike. This is probably the largest continuous gas field east of the Mississippi

Jan 1, 1943

By Iley B. Browning, Louise Barton Freeman, Coleman D. Hunter

During 1942, production of oil in Kentucky reached a total of 4,169,163 bbl. of which 1,807,809 bbl. came from eastern Kentucky. This was more than a million barrels less than in 1941, owing partly to the low price of crude oil, which almost eliminated wildcatting, and partly to spacing regulations, which limited the number of wells drilled in small, shallow pools where the pressures are not sufficient to maintain maximum recovery in widely spaced wells. In eastern Kentucky much of the oil was produced from outliers of the Mauch Chunk series at the disconformable contact of the Mississippian and Pennsylvanian. Although wells producing from this horizon, known as the Maxon, are sprinkled over the entire area, the greatest concentrations are in Martin, Floyd, Knott and Pike Counties. A new 30 to 40-bbl. well has been completed in this formation in ,Pike County, where the carbon ratio is so high that ordinarily oil would not be expected. Pike County is one of the largest producers of Maxon gas, and the offset well to this oil well produced gas. Of the 412 gas wells drilled in Pike County, 12.2 per cent produced gas from the Maxon horizon. During 1942, the old Menifee " Cornif-erous" field, the Mariba-Denniston field, was redrilled between old wells, and although it did not produce any large amount of oil it did contribute 2018 bbl. In the oldest oil field in eastern Kentucky, the Ragland pool, operators are cleaning out abandoned wells and are using this oil for fuel oil. There is a possibility that some of this may be used in the future as distilled fuel oil. Eight wells were completed in 1942 in the Jackson County gas field. The development of Jackson County, which was started in 1934 and in which commercial quantities of gas were encountered at a depth of 1100 to 1200 ft., has become of importance in 1942 with the completion of eight wells, making a total of 24 commercial producing wells with an average rock pressure of 140 lb. At this time the gas is not being marketed. In the last year it has been found that these wells, which produce from the Niagaran dolomite ("Cornif-erous"), respond to acidizing and the production has been thus greatly increased. There has been less development in Estill and Lee Counties than for several years. Two wells were drilled in Greenup County, one of which had a show of oil in the Berea sandstone. One deep test, drilled by the Owens-Libbey-Owens Co. in Lawrence County, was dry. This well was drilled to a depth of 4975 ft. into the top of the Clinton shale sequence. Of the 202 wells completed in Floyd, Martin, Knott and Pike Counties, 187 were gas wells, 3 oil wells and 12 dry holes. In Floyd County 66 per cent of the gas production was from the Devonian-Mis-sissippian black shales, 53 per cent in Martin, 79 per cent in Knott and 65 per cent in Pike. This is probably the largest continuous gas field east of the Mississippi

Jan 1, 1943

By D. T. Novick, M. B. Bever, B. Roessler

Ordered and disordered specimens of the alloy CusAu were cold worked and then annealed at 2880, 310°, and 340°C, together with disordered unworked specimens. me resistivity decreased during annealing mainly as a result of ordering; the resistivity measurements suggest that in cold-worked specimens the growth of antiphase domains is impeded. The strength properties increased during annealing at 288 "C; in cold-worked specimens this increase was lo a level above that for cold-worked specimens which had not been annealed. X-ray diffraction showed that after annealing for a few hours at 288ºC, the long-range order increased to a constant value; additional annealing at 288ºC resulted in the growth of antiphase domains in which the degree of order was constant. Changes in peak breadth and particle size confirmed that in cold-worked specimens the major effects of cold work were not eliminated during annealing at 288 "C, although a slight recovery process occurred. When a specimen of the alloy Cu3Au is heated to a temperature below the critical temperature (388ºC), long-range ordering tends to occur in a specimen containing less than the equilibrium amount of order characteristic of that temperature Ideally, a specimen of Cu3Au contains no long-range order if it has been quenched from above the critical temperature. Long-range order is reduced by cold work. If cold-worked specimens are heated, restoration processes such as recovery and recrystallization may occur,

Jan 1, 1963

By D. T. Peters, C. R. Cupp

Aging of commercial 18 pct Ni maraging steel and of related binary, ternary, and quaternary alloys has been studied by electrical resistivity, X-ray diffrac-tion, and hardness measurements. The aging process is in three stages: 1) recovery of martensite; 2) two precipitation reactions; 3) formation of nickel- rich austenite. The main objective of this work was to discover the nature of the Co-Mu interaction. Addition of cobalt to the Fe-18 pct Ni-5pct Mo alloy results in acceleration of the pvecipitation reaction by increasing the super-sat~lration 0f molybdenum. The cobalt-containing al- loys show no incubation period for the precipitation reaction, but the alloy without cobalt shows an initial slow reaction. These results are interpreted in terms of precipitation on dislocations. At low aging temperatures, the presence of cobalt leads to the appearance of a second type of precipitate which is a particularly effective hardener. Cobalt was found to retard the formation of austenite. Overaging is a combination of classical overaging and the formation of austenite in the structure. he- activation energy for the precipitation reaction determined from resistivity ,measurements is 42.8 kcal per mole and the growth of the precipitate is found to obey at law at high tenzperatures and a tU3 law at low temperatures. HE mechanism of strengthening of the 18 pct Ni maraging steels has been studied extensively since 1962.'-? The strengthening is due to precipitation hardening of the martensitic matrix. The main precipitate is an inter metallic compound involving molybdenum, but there is disagreement about its identity.

Jan 1, 1967