Search Documents

By C. A. Shook, W. H. W. Husband, D. B. Haas

Introduction Although previous studies1,2,3 have been made, no correlations for pressure drop have been proposed. This is probably because severe particle breakage occurred and pressure drops changed substantially with time. A quantitative statement of the relationship of pressure drop to the parameters of the system is desirable for lignite since, unlike higher rank coals, lignite slurries are thixotropic. The present investigation was undertaken to quantify the pipeline behavior and required continuous monitoring of pressure drop and size distribution.

Jan 1, 1980

By Edwin B. Wilson, Charles F. Cockrell

The application of evolutionary operation is proposed for the cleaning of coal by the heavy media process. Analysis of the data given suggests some benefits that may not be immediately appreciated unless evolutionary operation is applied. For example, while it may seem obvious to increase specific gravity when the ash and sulfur content of the clean coal is lower than that allowed, evolutionary operation may show that an increase in feed rate or an increase in both feed rate and specific gravity would be a more profitable alternative. In addition, by using evolutionary operation, up-to-date knowledge of the effect of change of feed rate or specific gravity on yield and product quality is available. This information facilitates confidence about decisions made in regard to the day-to-day operation of these units. A number of other applications in the minerals industry are proposed. An application of evolutionary operation in a related field is also given where a large number of variables were required to be optimized.

Jan 1, 1969

By Mark R. Lamb

THE various methods of treating pulp in air-agitation tanks offer problems for experiment and study which are fascinating as well as practical. The usual method heretofore has been to fill each tank in turn, agitate the mixture the required period and then discharge the treated pulp into a storage-tank, from which it. is drawn to the filter as required. A later method is to run the pulp from the tube-mill, classifier, thickener, or settler into the first of a set of tanks, and thence continuously or in series through the remaining tanks, finally drawing off the pulp to a continuous filter, or to a pulp-storage tank if the filter is of the intermittent type. It is this method which I propose to discuss here in a preliminary way, with the idea of going exhaustively into the examination of the results of a series of experiments in a later paper. It may be of interest to note that the design of a cyanide-plant has recently been completed in which the estimated cost of the agitation-tanks, storage-tanks, and pumps was 30 per cent higher for the charge-agitation arrangement than for the series plan. The first question in studying the series method is, "What is the actual period of treatment undergone by the pulp?? One first supposes that by chance some of the pulp may get through with little or no treatment, while other portions may stay in the tanks a needlessly long period. The former is not probable or even possible, and the latter is, practically, true to only a limited extent. The greater the number of tanks the greater is the percentage of chance that all the pulp will be treated equally. Without going into the mathematical analysis of the problem (which is of little value, since it is based on problematical premises), its important terms may be clearly grasped by thinking of, or " visualizing," the conditions when,

Jan 1, 1910

By R. V. Lundquist

Leaching manganese-bearing materials with NaOH to remove caustic-soluble silica has been demonstrated as a method for upgrading manganese. Those materials containing opaline varieties of silica respond most readily. Spent leach liquors are regenerated by treatment with lime to precipitate calcium silicate and to reactivate the NaOH for leaching. ALL of our larger domestic deposits of manganese are very low grade, but estimated tonnages in these deposits are large enough to constitute a potential strategic reserve of manganese for emergency periods, provided these ores can be upgraded sufficiently to meet industrial specifications. Many types of processes have been suggested for upgrading these ores, several have been studied in pilot plants, and a few have attained limited commercial production for special purposes. The hydrometallurgical process to be described below proposes a leaching operation for removing caustic-soluble silica and other gangue minerals and consequently upgrading a manganese ore or flotation concentrate to a commercially acceptable moduct. It is known that some forms of silica and some silicate minerals are soluble in NaOH solutions under suitable conditions. This new process proposes to use NaOH for removing the soluble materials from manganese ores or concentrates and, as a result, upgrade the manganese content. Since spent leach liquors are not efficient leaching agents the liquor must be treated with lime to precipitate calcium silicate and reactivate the NaOH. Experimental Procedure Manganese-ore samples ground to —35 mesh were leached in iron containers into which the ore sample and appropriate NaOH solutions were placed. Flotation concentrates were already ground to —200 mesh. The slurries were then placed on a hot plate or into a pressure digester and stirred continuously during the period of digestion. Where the- digestion was performed at atmospheric pressures, water lost by evaporation was replaced at regular intervals to maintain approximately a constant volume of slurry. In the pressure digester, volume changes were not controlled. After digestion, the slurry was allowed to cool enough for easy handling, but it was filtered hot, 50" to 70°C, on a Buechner filter. Filtration under these conditions was satisfactory. The resulting filter cake was washed and dried. In most instances, a single leach would not produce maximum extraction of silica from the ore sample; consequently, the dried tailing was treated again in the same manner with a fresh solution of NaOH to obtain an additional extraction of silica. This procedure was repeated a number of times to get the maximum extraction of silica. Usually three or at most four stages of leaching were adequate for this purpose. This leaching procedure was used for obtaining the data reported in this paper on the effects of NaOH concentration, pulp dilution, temperature, and time of digestion on the efficiency of extraction of silica from the ore sample. The experimental procedure does not match industrial methods. consequently tests for counter-current leaching were set up. Data from these tests are not yet complete, but in a qualitative way they indicate that thickeners between stages of leaching will be satisfactory and that the quantity of silica in a leach liquor moving forward to a new solid has only a minor effect on the quantity of silica extracted from the new solid. A pilot plant is now being designed for operation in the near future to test and evaluate the merits of this process.

Jan 1, 1954

By James F. Kemp

The Bulletin of the Institute for March, 1911, is chiefly devoted to papers upon the iron ores of northeastern Cuba. At that time information about the new developments in the peculiar brown hematites of the region was becoming widely circulated and interest was especially keen. For some years exploration had been conducted with pits and trenches and so great an area had been shown to contain ore in the Mayari, Moa, and Cubitas or San Felipe districts, that the reserves conveniently situated for the consumption of American furnaces were estimated as quite two billions of tons. In the subjoined footnote will be found a list of the principal papers of special interest which have already been published.' The further remark may, however, be made that the

Jan 1, 1915

By G. S. Hume

The production of petroleum in Canada is relatively small in proportion to the amount of oil consumed. Production figures are given in Tables 1 and 2, which show that the production in Alberta for 1934 was more than for the whole of Canada in 1933. The production of natural gas for Canada is shown in Table 3, In Turner Valley, the largest producing gas and oil field in Alberta, seven naphtha wells from the Paleozoic limestone and one crude oil well from Lower Cretaceous strata were completed during the year. Six-

Jan 1, 1935

By R. D. Carter

Nurnerical .solutions are presented to some problems of unsteady-state radial flow of gas in which Darcy's law holds. These solutions are intended to aid in explaining the observed behavior of gas wells during drawdown tests. The variation of viscosity and Z-factor with pressure is accounted for in the solutions. Results are presented for three types of problems: (I) unfractured wells producing at a constant rate, (2) fractured wells producing at a constant rate and (3) unfractured wells producing through a critical flow prover. In the critical-pow-prover solutions, a correction of the calculated well-bore pressure to account for non-Darcy flow is made. A good correlation is shown between the solutions to the problem of Type 1 and the corresponding diffusivity-equation solution. Using this correlation, the diffusivity solution may be used to obtain gas-well solutions. The solutions to the problems of Type 2 illustrate the difference in drawdown-curve behavior to be expected between fractured and unfractured gas wells. Methods for estimatting fracture radius and flow capacity are presented and verified from solutions of Type 2. The solutions to the problems of Type 3 illustrate the differences to be expected between critical-flow-prover drawdown tests and constant-rate tests. An equation is presented for correcting critical-flow-prover data to constant-rate conditions. A description of the methods used in obtaining the solulions appears in the Appendix. INTRODUCTION It is necessary for many engineering purposes, such as predicting future deliverability performance, to be able to relate bottom-hole flowing pressure, formation pressure and flow rate for conditions of stabilized flow in gas wells. This information is customarily given as a plot of on logarithmic co-ordinates. It is desirable to be able to predict stabilized performance curves for gas wells based on data obtained from drawdown tests of short duration. Tests of long duration may be wasteful of gas, and low-permeability wells do not stabilize in a short-duration test. Although it is now commonly recognized that non-Darcy flow plays a significant part in gas-well behavior, it is believed that an understanding of transient behavior of systems obeying Darcy's law is still important in the interpretation of short-term test data, and the prediction of stabilized performance curves therefrom. In this connection, an equation for correcting Darcy flow It seems likely that solutions of the type presented herein, combined with the non-Darcy flow correction of the type of Eq. 1 and the usual laminar-flow skin factor, could provide a model which would adequately explain transient gas-well behavior for times after the non-Darcy flow region (which should be confined to a small area surrounding the well) has been established. The solutions presented in this paper are for three types of problems: (1) unfractured wells producing at a constant rate, (2) fractured wells producing at a constant rate and (3) unfractured wells producing through a critical flow prover. In the problems of Types I and 2, no corrections for non-Darcy flow were made in the results presented, since it was reasoned that the constant-rate boundary condition would facilitate such a correction if it was desired later. For the problems of Type 3, however, a condition of varying flow rate required that a non-Darcy flow correction of the type of Eq. 1 be included. This was done. Based on the numerical results presented, a number of approximations and a correlation are presented which may be useful in analyzing gas-well test data. It is assumed that the system can be described as a finite cylindrical gas reservoir produced by a single cylindrical well located at the center of the reservoir. Flow is strictly radial.

By John Wellington Finch

In August, 1927, the writer examined certain copper deposits in New Mexico1 which occur in beds of sandstones and shale, and in connection therewith reviewed the literature upon deposits of this type. Such deposits are known and have been reported upon at various points in Texas, Oklahoma, Arizona, Colorado, Wyoming and Utah, but in New Mexico they have been given more development than elsewhere and apparently occur there more conspicuously than in the other states. Some 25 years ago the writer examined deposits of similar origin in northern Arizona and more recently other deposits in western and southwestern Colorado, and these examinations have led him to realize how widely scattered are the deposits and how generally noncommercial they are. On superficial development, to one without a comprehension of their geologic nature, they are alluring on account of occasional small amounts of high-grade ore and much misplaced capital has been expended upon them. This paper, therefore, aims to present briefly certain theories of genesis, some details of which may possibly be new, and to lead up to practical conclusions which may be useful to other geologists and engineers. A bibliography of the more important literature upon such deposits is given below.2 Coffin's Bulletin upon the Radium, Uranium and Vanadium Deposits of Colorado, published in 1921, is a particularly clear discussion. The most comprehensive recent statement is Butler's.

Jan 1, 1928

All the TECHNICAL PUBLICATIONS and PREPRINTS published in 1932 are available at Institute headquarters. They are also on file in public,, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. Copies of the TECHNICAL PUBLICATIONS have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division;. G-Petroleum .Division; H-Nonmetallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Copies of PREPRINTS may also be obtained from the Secretary's office. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. Nonmembers may purchase the papers at the prices mentioned. METAL MINING TECH- NICAL PUBLI- - TITLE AUTHOR MEETING TRANS. CATION VOLUME No. AND PAGE* 484-A.45 Propeller Type Mine Fan at Moose A. S. Richardson New York 102, 86, 93 F.52 Shaft, Butte, Montana (13) Feb., 1932 487-A.46 Progress in the Improvement of Max H. Barber New York, Methods and Equipment at Feb., 1932 Open-pit Iron Mines on the Lake Superior Iron Ranges (9) Pre. Sand Filling through Pipes and Lucien Eaton New York, 102, 33, 41 Boreholes (9) Feb., 1932

Jan 1, 1932

By D. L. Ritter, N. J. Grant, B. C. Giessen

The crystal structures of eight of the nine intermediate phases in the Nb-Rh system were investigated by X-ray techniques. The following structures occur: a,Nb3Rh (Cr3O type);o(ofe - cr type) (H.T. phase, structure unknown); Q2 (AuCU type); a, (orthorhombic, analogous to a,, (Ta-Rh)); a (AuCd type); a,, (monoclinic, related to samarium type); a-8 (VCo3 type); a, NbRh, (AuCu, type). Structural relationships between the six close-packed intermediate phases are discussed and a comparison with the Nb-Ir, Ta-Rh, and Ta-Ir systems is made. In the Nb-Rh phase diagram,' nine intermediate phases were encountered. In order to understand the phase sequence in the diagram and to be able to plot atomic volumes, several unknown crystal structures had to be worked out. These and the evi-

Jan 1, 1964

By Dale A. Augenstein, S. C. Sun

A primary concern in the solution of any solid waste disposal problem is the characterization of the material. In the past, available methodology for the determination of coal refuse characteristics has been severely limited by the inseparable combination of organic and inorganic matter of which the refuse is comprised. The recent development of an electronic, low temperature asher which removes the organic material without alteration of the inorganic constituents has opened new areas of coal and coal refuse research. This study deals with the development of methodology for the characterization of Pennsylvania anthracite refuse through utilization of the low temperature asher. Seven samples of anthracite refuse were examined for verification of the methodology developed and information concerning the characteristics of the refuse.

Jan 1, 1975

By Arnulf Muan, Klaus Schwerdtfeger

Activity-composition relations in Pt-Cr and Pd-Cr alloys of low chromium concentrations UCr < 0.3) have been determined in order to ascertain quantitatively the extent of reactions to be expected between Cr2O3-containing oxide phases and platinum or palladium crucibles used as containers in studies of oxide equilibria at low oxygen pressures. This work is a continuation of similar work previously

Jan 1, 1965

By George W. King

The yield strength of a dispersion-hardened W-3.8 vol pct Tho,alloy, in both the recovered and recrys-tallized condition, was investigated and cornpared with that ofrecrystallized pure tungsten over the temperature range of 325" to 2400°C. It is deduced that the Orowan mechanism is obeyed in the recrystallized alloy. In the recovered alloy, a further enhancement of the yield strength results from the retained substructure which is stable up to temperatures in excess of 2700°C. Temperature and strain rate cycling tests were also performed, and the apparent activation energy for the deformation process was derived. This activation energy, - 3 ev, for the recovered and also the recrystallized alloy was about the same as that for re crystallized pure tungsten. However, the activation volume of the recovered alloy, -10-2 cu cm, was about an order of magnitude lower than that of the recrystallized alloy or pure tungsten. This fact accounts for an enhancement oj- the temperature dependence of the yield stress of the recovered alloy. A dislocation velocity exponent of about 4 to 13 was deduced frorn the strain rate cycling tests , which is in good agreement with values reported for tungsten single crystals. VARIOUS theories have been developed to explain the enhanced yield strength of a metal containing a dispersed second phase of small hard particles. These theories are thoroughly reviewed by Kelly and Nicholson.&apos; The theoretical models can be separated into two types. The first type assumes direct interactions between moving dislocations and dispersoids. One of the most widely investigated models for this mechanism is the bowing out of dislocations between the dis-persoids and their subsequent pinching off in order to bypass the obstacles. This is the well-known Orowan mechanism.&apos; The second type is an indirect effect of the dispersion because of its ability to stabilize to high temperatures the substructure introduced by cold working. In this instance, the increment in the yield strength is expected to be inversely proportional to the square root of the subgrain diameter. In the present work, a quantitative study was made of the strengthening effect caused by a thoria dispersion in a recrystallized W-3.8 vol pct Thoz alloy over the temperature range 325" to 2400°C. The results are compared with the increment predicted for the Orowan mechanism based on the calculations by ~shb~.~ In addition, the alloy was tested in the recovered state so that any additional strengthening resulting from the substructure produced during fabrication could be measured. The respective contributions can be separated in this manner, provided that the particle size distribution of the dispersion remains the same in both the work-hardened and the recrystallized state. Particle size distribution measurements showed that this condition was met in the present work. I) EXPERIMENTAL PROCEDURES A) Material Production and Fabrication. The alloy investigated is essentially the same as that reported much earlier by ~effries,~ who also found the strength of tungsten to be improved by the thoria dispersion. The procedure for producing the alloy consisted of mechanically blending a thorium nitrate solution in proper concentration with tungsten oxide (WO3) powder, followed by hydrogen reduction to metal powder. After reduction, the dispersed second phase is present as thoria (Thoz). The pure tungsten powder used for comparison was produced in the same manner except that the thoria doping step was omitted. The powders were consolidated by cold pressing and self-resistance sintering in hydrogen. The resulting ingot had a cross section about 0.6 sq in. and a density about 93 pct of theoretical. The ingot was swaged to 0.174-in.-diam rod at temperatures varying from 1650°C initially to -1200°C near final rod sizes. Two intermediate recrystallization anneals were employed during fabrication. Analysis of the swaged rods is reported in Table I. B) Electron Microscopy Techniques. Carbon extraction rrPxcas prepared by a technique reported by ~00&apos; were used to quantitatively evaluate the thoria particle size and distribution. Electron nlicrographs of extraction replicas were taken at 20,000 times but were then enlarged two to three times in printing. The areas photographed were randomly selected. A Zeiss Particle Size Analyzer (Model TGZ3) was used to count and measure the sizes of all particles present on the print. About three thousand particles were counted in determining a distribution curve. Electron transmission microscopy was used to determine the effect of annealing on the substructures of the materials. Thin foils were produced by a two-stage thinning process. The rods were first ground on emery paper to ribbons about 10 mils thick and then a jet of 5 pct KOH was used to electrolytically reduce a portion of the cross section of the ribbon. Final perforation was achieved by immersing the specimen in a 5 pct KOH solution and electrolytically polishing at a current density of about 0.3 amp cm-&apos;. The foils were examined with a Hitachi HU-11A electron microscope. C) Tensile Testing. Tensile testing was performed in an Instron Testing Machine equipped with a radiation-type vacuum furnace which operates at about 1O"S torr at temperatures as high as 2400 °C. The same furnace was used for annealing the tensile specimens.

Jan 1, 1970

By Eugene F. Broome, Hugh A. Walls

Self-diffusion coefficients were measured using the modified shear cell technique over a temperature range from 31" to 401°C. These data agree within experimental error with those of Petit and Nachtrieb, which were determined from 30°to 99°C. LIQUID self-diffusion behavior in gallium has been studied previously by Petit and Nachtrieb&apos; using their shear cell technique.&apos; Data were obtained in that investigation over temperatures ranging from 30.6 to 98.7"C, and these comprise the only published data for liquid gallium. In the work reported here, diffusion data were obtained from 30.8 to 400-9.Cusing a shear cell technique different from that of Petit and Nachtrieb. This modified shear cell method and the mathematical analysis for diffusion in a finite capillary geometry have been previously described.3 PROCEDURES AND ANALYSIS The segments of the modified shear cell were fabricated from types 304 and 316 stainless steel. No corrosion problems with gallium were encountered until attempts were made to obtain data at 500°C. The diffusion capillary diameter was 1.59 mm and capillary lengths for the four sets of cell segments used are given in Table I. Gallium with a purity of 99.999 wt pct was obtained from Var-Lac-Oid Chemical Co. The gallium-72 isotope used to measure the self-diffusion coefficients was produced from this inert gallium by irradiation in The University of Texas Reactor Facility, and was checked for radiochemical purity. Following a period of isothermal diffusion controlled to within 0.0l°C, the contents of each capillary section were emptied into a counting planchet, weighed to assure that gallium had not been lost during handling, and the radioactivity determined by windowless gas-flow proportional counting. Great care was taken to obtain a reproducible counting geometry for the samples. Diffusion coefficients were obtained from the solu-tion3 to the diffusion equation for the modified shear cell problem, viz.: in which B2= C2(t)Li + L2)- CSL1-COL2 P* (C0-Cs)(L1+ L2) and L, and L2 are the capillary segment lengths. The step-function initial concentration distribution was expressed as C(x,O) = C, for -L1 = x < 0 and C(x,O) = Co for 0 < x 5 L?. Also, C2(0 = ^- fcix,t)dx Computation of the diffusion coefficients was done numerically as described in our earlier paper.3 Because of the short half-life of gallium-72 (14.1 hr) and the relatively long counting times taken to give a precise value of the diffusion coefficient, it was necessary to account for the radioactive decay both during the actual count and between counts for different samples (before and after diffusion). Thus, the average count rate Cz(t) for a second sample counted from times t3 to t4 can be made consistent with the average rate Co determined for a first sample counted from times t1 to t2 by the relationship: N(e-»i-e-M») , , C2(f) " &-«,)(*-«.-«-»«) [21 in which N is the total number of counts taken and is the decay constant. RESULTS AND DISCUSSION The self-diffusion coefficients determined in this investigation are listed in Table 11. Values of the parameters used to calculate the coefficients are given in the table, as are values of the random counting error &apos; for the concentration ratio pz and the corresponding expected random variation AD in the diffusion coefficient. The quantity is calculable from: &apos;Cg — C2(t)} , „ ,2 .-„¦, M co-csl(ACs)J W in which AC is the error in the individual count rate. The mean values of the diffusion coefficients within each temperature group are also given in Table 11. Such temperature groupings of data are reasonable because of the small variations between the temperature~.~

Jan 1, 1970

By George R. Cowan

A number of studies hare been reported of the effects produced in metals subjected to deformation by shock waves with maximum pressures ranging from tens to hundreds of kilobars. On the basis of the equations for the flow of mass, momentum, and energy through a stationary shock front, the macroscopic stress-strain curve for the resulting shock deformation can be calculated within narrow limits from the experimentally determined Hugoniol curve. In relatively weak shocks which are preceded by an elastic wave, the stress rises above the clastic limit only as plastic deformation proceeds cold thus the shock has a long toe. In strong shocks that override the elastic wave a high stress is applied without prior plastic deformation. A more important effect of increasing the shock pressure is the generation of shear stresses, called supercrilical shear stresses, that exceed the strength of the perfect lattice. A change in the mechanism of deformation is expected to result from the onset of supercritical shear. The shock disordering of ordered Cu3Au in strong shocks appears to be an example of such a change. It is suggested that the formation of fine twins in copper and nickel and the formation of structures which enable visible twins to be formed in the rarefaction ware, observed in copper and presumably in disordered Cu3 Au, are related to the occurrence of supercritical shear in shock dcformation. In recent years several studies1,2 have been made of the changes in structural and mechanical properties of metals produced by the passage through the metals of strong shock-compression waves ranging from about 50 to 800 kbar pressure. Recent work involving dynamic measurements of the shock compression "Hugoniot" curves 3-8 of many metals has developed techniques and provided data required to obtain the shock pressure and the (transient! plastic deformation produced in the shock-conlpression experirnents.9 Shock deformation has been found to be much more effective than slow deformation in changing the mechanical properties of metals, when the two are compared on the basis of equal plasti strain, Holtzman and Cowan9 made quantitative estimates of the shearing stress occurring in a shock front in a metal by assuming that the shearing stress is similar to that occurring in a shock front in a viscous, heat-conducting fluid, with the addition of a yield stress. Taylor&apos;s solution9 for a weak shock was used to estimate pairs of values of shearing stress and thickness of the shock front obtained by assumed choices of the ratio of effective kinetic viscosity to thermal diffusivity. It was noted from these values that. unless the shock front is extremely thin. heat conduction has slight effect, and the shearing stress is nearly independent of the mechanism of deformation. This mechanism does, however, determine the thickness of the shock front and the rate of strain. Furthermore, since the maximum possible shearing stress occurring in shocks of moderate strength does not greatly exceed the shear stress occurring in conventional slow deformation, the mechanism of deformation is not expected to be qualitatively different. The greater effectiveness of shock deformation in changing the mechanical properties of metals can be attributed partly to the fact that dislocations, when driven by near-conventional stresses, cannot keep up with the shock front, thus necessitating a higher dislocation density than required for an equivalent slow strain. The fast uni-axial strain occurring in the thin shock front would also be expected to cause a larger number of dislocation intersections to occur. In the upper range of shock pressures that have been studied the estimated values of the shearing stress exceeded the estimated shear strength of a perfect crystal. Under these circumstances it is reasonable to expect that the mechanism of deformation might be considerably different from that involved in slow deformation. Except for the observation by smith1 of twins in shocked copper, the effects of shock waves on metals did not show any obvious or large changes in properties that would indicate the onset of a change in the mechanism of deformation. The recent investigation of the effect of shock waves on ordered and disordered specimens of Cu3Au by Beardmore, Holtzman, and ever" showed a spectacular decrease in the amount of long-range order retained by initially ordered Cu3Au when the shock pressure was raised from 290 to 370 kbar. Since Dr. Holtzman and I suspected that this behavior probably was due to the onset of a shearing stress in the shock front in Cu3Au which exceeded the limiting shear strength of the perfect crystal. it was considered appropriate to examine directly the shock-front equations for a solid. and to obtain a sound estimate of the shearing stress occurring in the front using equation of state data obtained from shock studies. In this paper an estimate is made of the

Jan 1, 1965

By J. A. Barr, R. B. Burt, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long * Pebble is a commercial designation for the coarser fraction of finished phosphate from a washer, usually +14 mesh. distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By R. B. Burt, J. A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long * Pebble is a commercial designation for the coarser fraction of finished phosphate from a washer, usually +14 mesh. distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By J. R. Dawson, J. A. Glunt

VESTA No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin&apos;s byproduct coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War 11, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out. Mechanical loading at Vesta created new problems. It was found that selective mining, even when carefully applied, increased the refuse in the raw coal to such an extent that the washers at the mills were unable to handle it. Large tonnages of refuse were being transported, a reject disposal problem was created, and good metallurgical coal was being loaded out and lost. In addition, the selective method handicapped operation of the loading machines. Fig. 2 shows how the ash content of the raw coal increased as mechanization proceeded at No. 5 mine. New Preparation Plant: After an exhaustive study of this situation by J & L management, is was decided that a preparation plant should be constructed at the mines, capable of handling full seam mined coal and large enough to process full production of both No. 4 and No. 5 mines. It was decided that from the standpoint of inside operation and haulage the new plant should be located as near as possible to the old No. 5 tipple on the Monongahela River near Vestaburg. Full seam mining at Vesta could be expected to produce a tremendous volume of refuse along with the coal, since 14 to 16 in. of slate would be mined with an average 78 in. of coal. Disposal of this refuse required serious consideration in selecting a plant site. The only area near Vestaburg large enough for disposal of the plant refuse was across the Monongahela River at LaBelle. Ample space was available here, and construction at this location would not interfere with operation at the No. 5 tipple. It had been noted over the years that the sulfur content of the coal produced at Vesta was gradually increasing, and there was every indication that this increase could be expected to continue as the mines developed further from the river. It was decided to construct a three-part separation plant with complete blending facilities to produce both metallurgical and steam coal. In this system an attempt is made to reduce the sulfur in the metallurgical coal in a secondary cleaning process. Construction of the new preparation plant got under way early in 1947 and continued until the spring of 1950. The plant was designed to handle 2400 tph of raw coal containing 30 to 35 pct refuse. Cost of outside buildings and equipment was about $14 million. Total cost of the plant, together with improvements and changes made at this time, was approximately $21 million.

Jan 1, 1957

By George Stone

THE method of making oxide of zinc direct from the ore was invented and developed at the works of The New Jersey Zinc Co. at Newark in the middle of the last century. The process was invented by Burrows, who had not the ability, financial or technical, to work out the details necessary to make it of commercial value. This was done by Col. Wetherill, whose name is commonly attached to this process. The, grate bars used are also frequently called Wetherill grates, which is a misnomer because they were in common use for boiler firing at the time and he never claimed their invention. The invention of the process was due to the efforts of The New Jersey Zinc Co. to find a profitable means of working the ores from Franklin and Sterling Hill, N. J. These are a mixture of franklinite, willemite and zincite, containing about 20 per cent. of zinc. The first attempts were to make spelter, which were not successful, owing to the low grade of the ore and the fusibility of the residue. Failing in this, the next attempt was to make oxide in large muffles and reverberatory furnaces. This succeeded, although the cost of operation was high, the recovery low, and the quality of the product uncertain. In 1855, the new process was patented and has been in successful operation ever since. Essentially, the process is to spread a mixture of coal and ore on a body of burning coal on a perforated grate and blow an excess of air through the grate. The zinc is reduced in contact with the coal, volatilizes and burned by the excess of air in the upper part off the furnace and in the flues. It is then carried to the hag rooms by the excess air and products of combustion which are forced through the flues by fans. In its main features, the process is the same today as at the time of its invention, but the details have been so modified that it would hardly be recognized by its originators.

Jan 9, 1917

By C. A. Shook, W. H. W. Husband, D. B. Haas

Although previous studies l,2,3 have been made, no correlations for pressure drop have been proposed. This is probably because severe particle breakage occurred and pressure drops changed substantially with time. A quantitative statement of the relationship of pressure drop to the parameters of the system is desirable for lignite since, unlike higher rank coals, lignite slurries are thixotropic. The present investigation was undertaken to quantify the pipeline behavior and required continuous monitoring of pressure drop and size distribution.

Jan 2, 1979