Search Documents

By Ralph D. Parker

The Frood mine (Fig. 1) is 2½ miles north of Sudbury, at a general elevation of 1000 ft. above sea level. It includes the original Frood location, which was the No. 3 mine of the Canadian Copper Co., and the adjoining Frood Extension, which until 1929 belonged to the Mond Nickel Co. Mine Openings The mine is operated from two vertical shafts and one underground incline shaft. No. 3, for men, supplies and ore, is a vertical six-compartment shaft in the footwall of the south mining area and extends froin surface to a depth of 3045 ft. No. 4 is a vertical three-compartment shaft, 2500 ft. north of No. 3 and adjacent to the north mining area. It extends from surface to a depth of 3345 ft., and is used exclusively for hoisting ore. No. 5 shaft, inclined at 65' to the horizontal and of three compartments, is near No. 4 and extends from the 2600-ft. level to 77 ft. below the 3100 level. It is used for development below the 2800 level. The ventilation shaft, No. 1, with which this paper is directly concerned, will be described fully in the following pages. Mining Methods The orcbody is laid out in 80-ft. sections at right angles to the gcneral strike and numerically indicated from the southern extremity toward the north. Each section consists of a 45-ft. stope and a 35-ft. pillar, extending the full width of the orebody. Pillars and stopes are superimposed from level to level. The present mining territory is divided into two vertical areas, a north and a south area. Both areas have the same number of stopes on each level, the two areas being separated by 10 sections to be mined later. In a few instances, at the ends of the south area, where the orebody has narrowed, longitudinal stopes are used, of more than the usual 45-ft. width. It will thus be seen that mining operations hare been concentrated in two relatively small areas, offering

Jan 1, 1934

By Edward A. Sayre

In shaft sinking for cod mines, the cost item greatly influences the method adopted. This holds true especially when soft material must be traversed. The average life of a coal mine is short. This is due either to the limited area of the coal basin or to the great expense of maintenance and haulage underground when the entries are extended a considerable distance from the hoisting shaft. Therefore, the engineer in opening a coal mine is confronted with the fact that the cost must be kept within certain bounds else the venture will prove unprofitable. For this reason he may be prohibited from adopting certain safe, but expensive, methods that are used in sinking caissons for foundations, driving transportation tunnels, or other work of permanent construction. A common method of sinking through difficult ground employs the aid of a steel shoe pushed ahead of the shaft timbers. Another is the drop-shaft method. These two methods were used in sinking the main shaft and the air shaft of the Eagle No. 3 mine, at Des Moines, Ia., and the following data show the relative success and cost of the two methods of sinking under the same conditions. A drill log of the material to be penetrated was as follows (see Plate 1, Fig. 1): Thickness, Total Depth, Ft. In. Ft. In. Drift................................... 38 38 Sand..................................... 2 40 Drift.................................... 2 6 42 6 Jointed clay.............................. 5 6 48 Drift, firm............................... 10 6 58 6 Clay, with sand streaks.................... 3 61 6 Sand.................................... 12 73 6 Shale, with two thin beds of coal and thin strata of rock......................... 86 6 160 Rock.................................... 5 165 Coal..................................... 3 9 168 9 Main Shaft Sunk by Steel-Shoe Method This record shows the first 73 ft. to bc of drift material, the lower 12 or 15 ft. of which was sand. The remaining 92 ft. to the coal was shale and rock, and offered no trouble in sinking.

Jan 1, 1917

By William L. Fink, E. H. Dix, L. A. Willey

The results of a preliminary investigation of the aluminum-iron-manganese system showed that small amounts of iron (0.10 per cent) substantially reduce the solid solubility of manganese in aluminum. This is clearly shown in the photomicrographs of three alloys, Figs. 1 to 3. Fig. 1, of an alloy containing 1.04 per cent manganese after a heat treatment at 626° C. for 45 hr., shows only solid solution. This alloy contained less than 0.008 per cent iron. Fig. 2 shows the abundance of a constituent (which undoubtedly contains aluminum, manganese and iron) in an alloy containing 1.00 per cent manganese and 0.11 percent iron after a solution heat treatment at 625" C. for 63 hr. For comparison, Fig. 3 is included to show the relatively small amount of constituent (FeA13) in a similarly heat-treated aluminum alloy containing 0.10 per cent iron but no manganese. These data necessitated a reconsideration of the binary aluminum-manganese diagram that was previously presented,' inasmuch as the alloys used in that work contained from 0.02 to 0.05 per cent iron. This paper is the fourteenth of a series from the Research Laboratories of the Aluminum Company of America reporting the results of investigations of equilibrium relations in aluminum-base alloys of high purity. The purpose was to determine the phase relations in aluminum with aluminum-manganese alloys containing the smallest amount of iron that could be realized with the purest material available at the present time (less than 0.01 per cent iron). Since the previous publication from these laboratories, five investigations of the aluminum-manganese system have been reported. Krings and Ostmannz assigned the formula MnA14 to the compound at the aluminum end of the syst,em, and found a eutectic between this compound and aluminum at 649" C. and 3 per cent manganese.

Jan 1, 1933

By Walter Miller

Hundred-octane aviation gasoiine, toluene for T.N.T. production, high-quality lubricating oils for the needs of aviation and the armed forces, and synthetic chemicals for rubber manufacture again commanded the top priorities of the petroleum refining industry in 1944, the third year of America's active participation in the war. The objective continued to be to produce more and more of these materials—to keep up with increasingly greater requirements. By the end of the year all of the new installations projected before 1944, with the exception of possibly two or three that will tail over into January or February of 1945, had been completed and put into operation. And with the completion and putting into operation of these various units and the consequent lessening of construction responsibilities and problems, the industry was put into position to concentrate on the new operations and devote much more of its time and effort looking toward maximum output, both as to quantity and quality from the new facilities. Aviation Gasoline Making high-octane aviation gasoline continued to be the prime requisite of refining activities during 1944 as it was in the two previous war years, with the sights at the end of the year set to still higher figures than those which had been previously projected. About July I the daily output had been raised to 400,000 bbl., with some few large plant installations still to be completed and put into operation. Indications were that by December production would be up to all requirements, with good inventories. However, although by the end of the year the industry was turning out something over 500,000 bbl. a day, the estimated requirements of the armed services had been raised by a considerable figure, owing to the greatly increased aerial activities both in the European and Far Eastern combat areas. By the end of the year, therefore, the picture had changed, with the prospect for a much longer continuation of the European war, so that even with the completion and putting into operation in the United States by January 1945 of the last two or three 100-octane units authorized prior to 1944, it was evident it would be necessary to make still greater efforts to increase output of existing facilities to keep safely ahead of the game. Efforts of the industry and the Petroleum Administration for War as well as the Technical Advisory Committee and other research and development groups are concentrated therefore on methods and means of further augmenting the produc. tion of all existing refinery facilities engaged in making 100-octane aviation gasoline and components entering into it. The goal will be reached.

Jan 1, 1945

By Roy A. Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a superior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

ENROLLMENT of both undergraduate and graduate mineral engineering students rose approximately 11.8 pct over last year to a total of 12,830. Leading again in the enrollment climb was ceramic engineering which increased by about 21 pct. Approximated increases in enrollment of the other mineral engineering categories, in order, were: metallurgical 17.7 pct; petroleum 13.3 pct; geological and geophysical 3.3 pct: and mining proper, the lowest with 2.9 pct. Total ECPD school enrollment climbed to 242,405 -just below the 1947 peak, but 14.4 pct higher than 1955. Engineering enrollments have shown a general increase since 1951, and freshmen enrollments have climbed steadily since 1950.

Jan 5, 1957

By Stanley Herold

A FEW notes on the occurrence and significance of mud volcanoes in Colombia may be of interest at the present time, owing to the renewed activity in geological exploration of, the coastal regions bordering the Caribbean Sea. The best-known volcanoes are found a few miles from the seacoast. One is situated to the south of Puerto Colombia; the second, to the east: of Cartagena near the village of Turbaco; and the third, near the village of Puerto Escondido south of the Sinu River. Others. are reported in more inaccessible localities. Usually they stand 2 1/2 or 3 ft. (0.762 or 0.914 m.) above the surrounding ground at the crater, though several craters from 10 to 20 ft. (3.04 to 6.09 m.,) apart will often build up an extensive mound at low gradient. The shallow mound may cover 1/2 or 3/4 acre (0.2 to 0.3 ha.) with an elevation of 12 or 15 ft. (3.65 or 4.57 m.) at the center. The craters are formed of hardened blue clay; the inside diameters vary from 14 to 24 in. (35.56 to 60.96 cm.). The rim is continuous, except on one side where there is usually a cut 3 or 4 in. deep, thus allowing an overflow. The craters are filled to the rim-cut- with a thick mixture of blue clay mud and water, which is kept in agitation by escaping gas. Fig. 1 shows the bubble in the act of bursting and Fig. 2 the appearance of the surface of the viscous fluid a second or so later. The frequency of the explosions is determined by the weight of the column of fluid in the neck of the volcano, consequently, such explosions are not synchronous in a group of craters. Ordinarily, there are two or three explosions in about 3' minutes. The supply of gas is small but steady and sufficient pressure must accumulate before the bubble can enter the column of fluid. The water is derived from the surface and enters the sedimentary strata not` far distant from the volcano. During long dry seasons, as the supply of water fails the volcano dries and geyser action ceases.

Jan 7, 1919

By Wilber Stout

In Ohio, the annual output of coke made from native coals has averaged not more than 70,000 tons, or about enough to run a 200-ton blast furnace. Raw coal locally mined from the Sharon, or No. 1, bed was used for iron smelting in Mahoning furnace at Lowellville, Mahoning Co., as early as 1846. This practice was continued in the Youngstown district until the coal became scarce and the Connellsville coke more popular. At present, the Sharon bed contributes a part of the fuel for the production of ferrosilicon iron at Jackson, Jackson CO. About one-third native coal and two-thirds soft coal are used. In this state, coke, on a commercial basis, was first made in Jefferson County probably about 1861 or 1862. The coals used were the Steuben-ville Shaft, or Lower Freeport, and the Strip Vein or Middle Kittanning. The practice, however, was discontinued before 1880 because of the competition of superior foreign cokes. Beehive ovens, later built at Leetonia, Columbiana Co., were operated for only a few years; the coal used at this place is the Lower Kittanning or No. 5. In a desultory way, slack from the Pittsburgh coal has been coked at a few places in eastern Ohio, and attempts, either for experimental or for commercial purposes, have been made in other parts of the state. Small quantities of coke were made from the Upper Freeport coal at Salineville, Columbiana Co., and near Nelsonville, Hocking Co.; the results were poor. Tests were made of the Middle Kittanning coal near Zanesville, Muskingum Co., at Moxahala Furnace, Perry Co., and at Washington Furnace, Lawrence Co.; the cokes were all high in sulfur and ash. Attempts were made to coke the Clarion coal at Vinton Furnace, Vinton Co.; a small battery of molding ovens and a pile of high-sulfur coke yet remain to tell the story. The Pittsburgh coal was coked on a commercial scale at Utley and at Lathrop, Athens Co., but the operations were not successful and were soon abandoned. These failures and indifferent successes are not to be attributed to a lack of demand for a first-class coke, as Ohio has held a commanding place for many years in iron smelting; nor to a deficiency of coals, as the state has a vast reserve of such material. They are to be ascribed to the inferior quality of the native products offered to the trade. The cokes

Jan 1, 1920

By Z. T. Bieniawski

The efficient and safe design of room-and-pillar coal mines still remains as one of the pressing problems facing the mining industry in the United States. Present day design is a trial-and-error approach based mostly on experience. Although much research has been directed to stability of mine roofs and coal pillars, no generally-accepted design method has been formulated. This paper reports on a three-year research effort directed to an improved design of room-and-pillar coal mining in the U.S.A. Essentially the study consisted of three aspects: (i) determination of stable roof spans; (ii) determination of the strength of coal pillars; and (iii) determination of safety factors for room-and-pillar coal mining in the United States. Furthermore, three novel approaches were utilized during this research: i) the "petite sismique" technique was assessed for possible determination of coal pillar deformability ii) the "Geomechanics Classification" was extended for determination of safe roof spans in room-and-pillar coal mining. iii) a national survey of the current design practice and mining dimensions was performed with the aim of assessing factors of safety for room-and-pillar coal mining The outcome of this work, which is summarized in this paper, is a design code for room-and-pillar mining in the United States.

Jan 1, 1983

By Fred Bond

THERE is acute need for a method that will measure the size distribution of finely di-vided materials, particularly when the par-ticle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the sam-ples produced are adequate for a consider-able amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essen-tially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the set-tling rate. The balance appears to be in-herently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have re-stricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investiga-tion might lead to modifications that would make it a valuable tool for the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribu-tion determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used, in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared, early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could he accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the dis-tribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1939

By O. Jay Myers

The war effort has furnished the necessary impetus for better magnesium foundry practice. Four or five years ago, there were but a few formulas in general use for core-sand mixtures for magnesium castings. Certain sands, binders, and inhibitors were specified and the proportions of these materials in each mixture were maintained between very narrow limits. As more and more war industries entered the field, much research was carried out and methods and practices were improved. Magnesium founding is still in a state of flux; therefore it is not uncommon to find one foundry spraying inhibitors on its cores, and another foundry using sand mixtures with incorporated protective agents. The basic core or dry-sand mold mixture for magnesium in use today is compounded with sand, core oil or resin binder, cereal, and moisture. Core oil or resin binder are added for baked strength while the cereal binder and moisture are for green strength. The normal mixtures (based on the weight of the sand) contain from o.5 to 1.5 per cent of both cereal binder and core oil, and the moisture content variesbetween 1.5 and 5 per cent. The ratio of core oil to cereal binder varies from 60:40 to 40:60, while the correct amount of moisture depends upon the method of coremaking. Protective Agents In all magnesium practice, protective agents are used in conjunction with the core and molding sands to prevent oxidation of the metal. The use of these inhibitors is not novel, but publications covering this field are not entirely adequate. Beck1 says: Magnesium alloys decompose water to form magnesium oxide, hydrogen being liberated in the process (Mg + H2O ? H2 ?+ MgO). This reaction results in the blackening of the skin and the appearance of areas of porosity on the casting surface, the cavities of which are filled with a grey oxide powder (these are termed 'burns'). Although sand cores for magnesium castings are thoroughly dried during the baking cycle, burning will take place on the casting5 unless the metal is protected properly. This type of burning is more difficult to define than the "water-magnesium" reaction cited by Beckl A possible explanation may lie in the following equation: 2Mg + O2—> 2MgO Here, the source of the oxygen is not water, but the air in the mold cavity, together with the chemically combined oxygen in the core-binding media. Generally, two methods are used to prevent this reaction from taking place.

Jan 1, 1945

By Michael B. Moolman

Both conventional and nonconventional process alternatives for gold recovery from cyanide heap leach solutions are discussed in terms of possible flowsheets. Conventional process alternatives include carbon adsorption and zinc dust precipitation, while nonconventional process alternatives include resin ion exchange, solvent extraction, and direct electrowinning. These strategies for gold recovery are compared on the basis of technological features and on the basis of process economics: Review of the technology status and process economics suggests that improvements for conventional process alternatives are possible and that further development of nonconventional process alternatives is warranted.

Jan 1, 1984

By Clement K. Chase, F. Milton Lewis, Roshan B. Bhappu

In situ extraction for copper, gold and uranium, generally involves several common alternative processes and techniques. These include dump leaching, heap leaching, leaching of fractured ore in-place or bore hole mining and unit operations such as cementation, solvent extraction, ion-exchange or carbon-in-pulp. Since the metallurgical effectiveness and economics of such processes and unit operations are well established, it would be possible to select the optimum alternative for extracting either copper, gold or uranium from their ores using in situ extraction technology. In this paper, efforts have been made to provide metallurgical evaluation as well as capital and operating costs for the various processes and unit operations. Attempts have also been made to utilize the above costs in preparing feasibility studies for in situ extraction of these metals.

Jan 1, 1976

By J. P. Manning

UNQUESTIONABLY, the outstanding feature of the piping for the sulphide plant is the large amount which had to be done in almost every size from instrument tubing to 84 in. OD pipe. In this article the piping will be considered under the main headings of Yard Piping and Building Piping. Tables I and II give data concerning the individual systems. In the case of yard piping the figures pertaining to lengths and weights are approximately correct; those for building piping are given only for the concentrator and smelter buildings where the amounts were the most extensive. Yard Piping The installation specifications for yard piping called for all sizes larger than 12 in. to have welded joints made with outside welding rings. This type of joint was selected over butt-welded joints because less time would be needed for lining up, damaged pipe ends would be less of a problem, and deflections up to 6° per joint could be made when necessary. These advantages were thought to outweigh the disadvantage of the greater amount of welding required. Yard piping in sizes of 3 to 12 in. was specified to have butt-welded joints made with inside welding rings which were intended to facilitate lining up and keep welding material out of the lines. Screwed connections were specified for sizes under 3 in. No protective coatings or wrappings were required on pipe to be buried because of the dry climate at Chuquicamata.

Jan 1, 1952

TO WE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-The following report covers briefly some of the more important activities of the Institute during the year 1923. In my report for the year 1922, I drew attention to the falling off in membership of the Institute due to the depressed condition of the mining industry in several lines and the inability of many of our members to find profitable employment in mining or its associated branches. A number who were unemployed during 1922 established connections during 1923, but a still greater number have been forced to resign or drop their membership during 1923. Fortunately, the number dropped is not so great as in the previous year. The Employment Service conducted by the four Founder Societies bears witness to the trend in business. For the young men just out of college, there are plenty of opportunities at small salaries, there are plenty of opportunities for them as laborers; but for the mature members, those of experience, there are few calls. During the last eighteen months, our Employment Service has been able to place only six of our members out of every hundred engineers for whom it has found work. Another loss which this Society has suffered, but which is not felt so keenly by our sister societies, is in its foreign members. The A. I. M. E. has always had a large foreign membership, but of recent years exchange has been so heavily against many European and South American countries that a large number of members residing abroad have been compelled to relinquish their membership. Almost invariably these members express keen regret because of the necessity that confronts them, and almost invariably the writers express hope that present conditions will not last long and that they will soon be able to ask for reinstatement. Having stated the darkest side of the picture first, it may now be drawn to your attention that in spite of these losses the number of persons applying for membership was decidedly encouraging. From the quality point of view, the membership has not gone backward. The Membership Committee has declined to recommend many

Jan 1, 1925

By B. Zondek, W. T. Cardwell, J. W. Sheldon

The fundamental equations that are used to describe two-phase fluid flow in porous media are Darcy's law for each phase and an equation of continuity for each component. The special case of one-dimensional, incompressible, two-phase flow has received much attention in the petroleum engineering literature.1-10 The basic paper on the subject is that of Buckley and Leverett.2 Buckley and Leverett showed that one could eliminate the pressure and obtain a single partial differential equation for the saturation. They solved this equation for the case when gravity and capillary forces are negligible. A frequently encountered property of the solution of the basic partial differential equation is that, as time progresses, the saturation becomes a multiple-valued function of the distance coordinate, x. Buckley and Leverett interpreted the formation of multiple values as an indication that the saturation-distance curve had be-come discontinuous. They developed a method of determining the position of the discontinuity from a material balance. We solve the Buckley-Leverett partial differential equation using the method of characteristics and the concept of shocks. Our treatment is analogous to treatments used in the theory of supersonic compressible flow." Although the numerical results obtained are the same as those obtained by previous methods, we believe that this approach is more logical and has broader applicability. It can, for example, be generalized to treat the case when the fluids are compressible. It is not clear how one would go about doing this using the method of Buckley and Leverett. To illustrate the power of the method of characteristics with shocks, we solve a problem in gravity segregation which has not been treated previously in the literature. A special case of the general method developed here was used by Welge, to solve a particular fluid displacement problem. We consider two-phase incompressible flow along the vertical direction x in a porous medium. We assume that there is no flow transverse to .x. We measure positive in the upward direction. The fundamental equations are obtained from Darcy's law and the mass conservation law. Since the two phases are incompressible, mass conservation is equivalent to volume conservation.

By H. D. Pearsall

It is well that the usual system for supplying water at high pressure purposes of hydraulic mining possesses serious disadvantageense, delay and large annual repairs. Where plough work possible, the first expense of the ditch is moderate; but it is verynree years before the work is solid and the ditch water-tight, lxPenditure for repairs being needed during this time and greaf water occurring. Moreover, in the course of a long ditch, it happens that part of it has to traverse a diffi cult country fluming, masonry, or other expensive construc tion is necessich makes even the first cost high. The life of flumes is also) The ad visa if pumping water instead of supplying by gravity has therefore been suggested, when sufficient water-power for the purpose oping happens to be available. But the expense of the requiuchinery and its complication, which involves skilled attend expensive wear and tear, has hitherto pre vented. The author ever, having been called upon to make plans and estimates for Lulic works for an extensive placer-mine in Colo rado, has such in devising pumping arrangements which are free from these sections, and are in fact estimated to cost less than half what a din the usual plan would cost. Several incidental advantages in plan also accrue, which will be referred to more particularly be The works placer-mine have not yet been carried out, on account of final arrangements, but in the meanwhile an hy draulic 'engineilar to that designed for the mine, has been con structed and so work for other purposes in England; and in order to explane plan which I have recommended for working the placer-mine will' describe this, which is actually at work, in preference to cibing the one which is not yet constructed. The engine machine acts on the principle of the hydraulic ram

Jan 1, 1888

By S. Fukushima, E. Kimura

In the Mitsubishi beneficiation process of ilmenite, chlorine is regenerated in the dechlorination furnace where the gases produced from a selective chlorination of ilmenite are directly introduced. The present paper describes a reaction mechanism and mixing characteristics of the reactant gases for dechlorination of ferric chloride with oxygen. A furnace of a small diameter where the reactant gases passed through in the state of nearly plug flow was used for determination of the effects of temperature and of partial pressures of ferric chloride and oxygen on the rate of the reaction. The experimental data of the reaction rate were applied to various models for calculations of the rate equations and the most suitable reaction model was determined. The results of the experiments also showed that effects of gas mixing onto the reaction rate could not be ignored, so that experiments of gas mixing was carried out. Gas flow patterns and scale effects were observed with use of transparent model furnaces of different sizes.

Jan 1, 1976

By K. L. Woodruff

The first step in processing municipal solid waste (MSW), principally household waste, for resource recovery is usually shredding. A trommel has been investigated as a step to precede shredding. This way abrasive inorganic materials, such as stones and metals, would be removed prior to shredding, thus lowering the amount of feed and hence maintenance on the shredder. In addition, friable materials such as glass would be removed in large pieces, rather than pulverized too mall to process for recovery. The utility of a trommel for these purposes was investigated on a pilot scale using a unit 9 ft diam by 10 ft long with 4-in. square clear openings. Experimental results indicate that up to approximately half of the MSW may be removed as -4-in. material prior to shredding. The -4-in. fraction contains approximately 70% of the metals and 95% of the glass present in the MSW feed to the unit. Scale-up and cost information necessary for the design of a 60 to 70 tph unit is developed.

Jan 1, 1977

By Richards R. Vandervoot

T HE creep behavior of many polycrystalline metals at moderate stresses can be described by the empirical relationship: where Em is the minimum creep rate, A is a constant, a is the applied stress, E is the average elastic modulus at the test temperature, and D is the self-diffusion coefficient.&apos; This equation is generally applicable for strain rates of less than around 10-5 per sec and temperatures greater than about one-half the melting point in absolute units. Under these conditions atomic mobility plays an important role in the deformation process, and steady-state creep occurs when a dynamic equilibrium is reached between the generation and recovery of dislocation substructure. Although several theoretical mechanisms have been proposed to explain the creep of polycrystalline solids,2"4 the dislocation climb model2 is in accord with most experimental observations. The majority of creep data used to develop Eq. [1] came from metals with either the fcc or hcp crystal structures. However, on the basis of results for a and 7 iron as well as those for a and a thallium, Sherby concluded that the high-temperature deformation behavior of close-packed metals and bcc metals is probably the same.&apos; The greater creep resistance of fcc and hcp metals and alloys on a relative temperature scale was attributed to lower diffusivities in the close-packed structures. To further compare the creep properties of fcc, hcp, and bcc metals, creep data for all six bcc refractory metals were analyzed according to Eq. [I]. The results are shown in Fig. 1. The sources of information for the quantities used to prepare this figure are listed in Table I, except for high-temperature elastic moduli. The latter data were obtained from Refs. 28 and 29. The dashed lines in the figure represent the range and breadth of data analyzed by Sherby for fcc and hcp metals. In general, the deformation behavior of all of the refractory metals, ex- cept possibly that of tungsten, can be represented by Eq. [1]. This correlation is strong evidence of the similarity that exists between creep of pure close-packed metals and creep of pure bcc metals. At (Em/D) < 108, the results of Flagella and Tarr on tungsten (W-1 in Fig. 1) agree with the five-power stress law, while those of Green (W-5 in Fig. 1) show a seven-power stress dependence. Where (Em/D) > 108, the stress exponents for other data on tungsten were in the range 10 to 15. It is possible that the creep rate dependence on stress in this region is not a power law but exponential (i.e., Em - eßo). However, it was not feasible to differentiate between these two cases because of the steep slope and scatter in the data. Note the inflection point in the curve for the data of Flagella and Tarr (W-1 in Fig. 1). The slope of the line changes from 5 to around 10 at Em/D = 108. The breakdown of the fifty-power stress law at high stresses is not uncommon in other metals, and this phenomenon may result from nonequilibrium conditions in the material such as excess lattice vacancies produced by rapid straining.30 The mechanical strength of a polycrystalline metal is related to its microstructure. Attempts to establish the influence of grain size on the creep rate of metals and alloys have led to a wide variety of results. For example, the following effects have been observed: creep rate decreases as grain size increases;31&apos;32 creep rate decreases as grain size decreases;&apos;,33 creep rate is a minimum at some critical grain size and increases with either an increase or decrease in

Jan 1, 1969