Search Documents

By J. L. Leland Myer

Some of the early experiments on the oxidation temperature of coal1 were undertaken in England in connection with a study of self-heating, or spontaneous combustion. It was then suspected that coals with low oxidation temperature were most likely to ignite by self-heating, but further experiments showed that many additional factors were involved. The oxidation temperature has importance as a physical property or characteristic of the coal. While only a few of the physical properties have been studied, they appear to have basic significance2 in the ultimate classification of all coals. When reliable data become available on the oxidation temperatures, as determined by standard and adequate methods, it should provide an additional basis for classification and comparative evaluation. Oxidation Temperature Defined For such a heterogeneous substance as coal is known to be, no simple definition of oxidation temperature can be established on a theoretical basis. If coals were homogeneous and of simpler structure, the accepted definition of "ignition temperature " as applied to simple gaseous mixtures might be adopted; that is, the temperature at which self-heating of the mixture sets in. But most coals self-heat slightly even at storage temperature, as evidenced by spontaneous combustion, and the definition for gases cannot be applied to coals with any exactness. By subjecting coals to suitable experimental conditions various oxidation characteristics can be obtained and examined for critical or significant stages of the oxidation process. Oxidation temperature itself must then be defined on the basis of such experimental results. Experimental Methods Attempts to determine critical points in the temperature functions of coal undergoing oxidation have resulted in the following experimental methods:

Jan 1, 1932

Seattle offered sunny, dry weather to about 2500 mining men who assembled September 10 to 14 for the 1961 American Mining Congress. The impact of snappy sessions on national mineral policy, state of the industry and foreign competition (to name only a few) was somewhat overshadowed by enthusiasm of conventioners for salmon fishing. This lordly fish, which mysteriously runs to its hatching place to spawn and die at this time of year, was not cooperating with the anglers in Puget Sound. However, this did not prevent consuming ample amounts of the deliciously prepared Quinault salmon at the "Potlatch" celebration.

Jan 10, 1961

By A. B. Kinzel

THE demands of the petroleum and chemical industries for steels to be used in pressure vessels and similar structures at artificially low tempera-tures are continually increasing, and the writing of proper specifications with suitable tests becomes increasingly important. Likewise, the selec-tion of suitable steels for such applications is of increasing concern to the metallurgist. It is generally recognized that highly alloyed steels of the austenitic stainless type retain their properties even at very low tempera-tures and represent the best technological solution of the low-temperature steel problem. However, in many instances less expensive carbon or low-alloy steels suitable for service within limited temperature ranges are available. The problem thus becomes one of defining the various factors involved in the production and fabrication of these less expensive steels and determining the temperature ranges in which their properties justify engineering application. Most of the applications involve welded structures, and the heat effect of welding as well as the nature of the weld metal are matters of prime concern. The first problem that the metallurgist faces is the determination of the type of test to be used as a criterion of the performance of the steel in low-temperature service. It has been generally recognized that the static properties of steel as determined in the ordinary tensile test undergo a gradual and relatively slight change as the temperature of test is lowered in the range of current interest; i.e., from room temperature to minus 120° C. It is further generally recognized that the behavior of steel under impact involving notch sensitivity is definitely affected at the lower temperatures. While the major subject of this paper is the effect of grain-refining deoxidizers, of low-alloy additions and of welding on the low-temperature notched-bar impact properties, an inquiry into the general behavior of steel under low-temperature impact testing is included. This is a pertinent portion of the investigation and the results thereof are

Jan 1, 1937

By James E. Lawver

Efficiency of industrial research and development depends on the ability of engineers and scientists to collect and present data to top management for decisions. In many cases, the data presented are so deceptive that management makes costly wrong decisions. Since management personnel often are selected on the basis of higher administrative quality than technical ability, it is the responsibility of the industrial scientist or research engineer to make certain that the data presented tell a completely ac- curate story of each industrial problem. It is rare that misleading data are deliberately presented, but when this is done, it is? of course, dishonest. The rise of deceptive data usually stems from the lack of knowledge of experimental design and statistical methods of analysis. Most of the better chemical engineering schools have recognized the need for courses in industrial experimentation and many of them offer complete courses at both graduate and un- dergrarluate levels. By contrast, many of the mining and metallurgical schools have not recognized the importance of industrial experimentation courses and some of them, in fact, do not allow credit toward a mining or metallurgical engineering degree for statistical courses even when taken as an elective. The sole purpose of this paper is to make a plea for mining and metallurgical schools to present required industrial. statistical courses for their graduates. It is true that fine industrial research has been accomplished in the past without the assistance of any statistical techniques. Industrial problems have also been solved without the use of digital or analog computers, electron microscopes or other modern conveniences. The fact remains, however, that the correct use of these modern tools tends to reduce the cost of research and to eliminate costly errors. A working knowledge of experimental design and statistical data analysis must simply be viewed as a valuable tool whose proper use will greatly reduce the cost of experimentation and minimize the cost of false conclusions. These statistical methods, however, simply cannot replace fundamental knowledge or, for that matter, "good horse sense". Nevertheless. an experimenter armed with fundamental knowledge and good horse sense but completely ignorant of elementary statistical techniques, may easily present his data in such a deceptive form to cause management to make incorrect decisions.

Jan 6, 1962

By J. L. Smith, A. L. Albee

This article presents a series of guidelines by which the geologist can evaluate the likelihood of surface faulting and its probable extent at any given site in Southern California and Nevada. The information is intended primarily for geologists concerned with establishing design criteria for proposed nuclear plants. The geologic problems involved in the location of a nuclear power plant are fundamentally no different from those for other types of installations. They fall into four main categories: foundation stability, landslides and slope stability, shaking due to earthquakes, and surface faulting. For problems in the first three categories the foundation engineer, the geologist, and the seismologist can provide criteria for plant location and design, and these problems can generally be economically handled by appropriate design measures for a project of the magnitude of a nuclear plant. However, problems in the last category — surface faulting — are more difficult to handle and require a unique evaluation. Accordingly, this paper will deal primarily with the problem of establishing design criteria for surface faulting, particularly as it affects nuclear facilities. A nuclear reactor is a power source that for greater safety is contained in a heavy, air-tight structure, just as gas, oil, water, and other power sources must be contained. Surface faulting is significant in that it may reduce the integrity of the containment by affecting critical exterior piping or by breaching of the containment. A similar significance exists relative to dams or tanks for the storage of water, gas, or oil, except that in these latter examples the breaching of the container automatically releases the fluids to do their damage. This is not necessarily the case with the rupture of a reactor containment structure because the function of the containment is totally protective, i.e., it is necessary only in the event that radioactive products are released from the reactor, and there are many other safeguards to pre- vent this release even if the containment is ruptured. At the present time, nuclear power plants must be located near large sources of water for cooling the steam generated. The construction of an industrial facility of any kind on the coast line is esthetically distasteful to most people since, unfortunately, there is not enough coast to fulfill all the needs and all the desires of all the people. In most cases where industrial facilities encroach on the lives of citizens, there is no mechanism other than zoning laws by which a person can effectively protest. But in the case of a nuclear facility, the public hearing required by the Atomic Energy Commission provides a forum for dissent, as in recent case histories, and the question of safety provides objectors with a weapon for fighting the construction of the plant. The nature of a public hearing for a nuclear plant is such that the prospective owner and operator must prove that there is no undue hazard, whereas the objectors need only demonstrate that there is a reasonable doubt. It is in this situation that geology becomes the Achilles Heel of nuclear power plant location. For his investigation, the geologist has natural exposures of rock at the ground surface and a limited number of trenches and drill holes to give him a fairly complete picture of the distribution of the various rock types. From the surficial data, he must infer three more dimensions — depth below the surface, past time, and future time. Unlike many problems faced by engineers, the geologist has only this one set of data from which to reach a conclusion — he is unable to reproduce the natural sequence of events in order to obtain another set of data for comparison. Hence, by the very deductive nature of a geologic conclusion, it is difficult to prove a geologic conclusion beyond a reasonable doubt even to other geologists — and perhaps one should say especially to other geologists because the experience and background of a geologist will strongly influence his conclusion, and no two geologists have exactly the same experience and training. The engineer and the public official would like the geologist to conclude that faulting cannot occur at a given site or to assign a numerical value to the probability of its occurrence — but no responsible geologist can do either of these things. Since government officials and others must make decisions that affect the public safety, it would seem that the geologic profession must attempt to establish criteria and

Jan 1, 1968

By H. Baldauf, H. Schubert

The structure of flotation reagents is important for their adsorption on mineral surfaces and thus for their flotation effectiveness. The influence of the structure of organic depressants on the flotation of fluorite and barite with anionic and cationic collectors was investigated using a modified Hallimond microflotation cell. In addition, adsorption, desorption, and electrokinetic results were employed to further elucidate the role and the correlation of the structural parameters for adsorption and the depressing effect. As hydrophilic reagents, different aliphatic and aromatic compounds capable of forming chelates with alkaline earth materials were used. For the depressing effect, the kind, number, and position of the polar groups in the molecule, as well as the structure of the reagent films play decisive roles.

Jan 1, 1980

By C. F. Knutson, Martin Felsenthal, J. D. Lung, J. D. Sudbury

This paper has been written to summarize the laboratory and field studies leading to injection of Pacific Ocean water into the Third Grubb formation. Laboratory tests for studying the permeabilities of cores to Pacific Ocean water are described. Resu1ts of these tests showed that the water could be successfully injected if it is chertzically stable, sterile, and properly filtered. Clay swelling was shown to be a comparatively minor factor in permeability reduction. Studies leading to development of an economical system for properly conditioning the ocean water are discussed. It was necessary to control pH, calcium carbonate deposition, bacterial growth, iron solubility. oxygen, and suspended .solids. A relatively simple system combining the use of sulifur dioxide, a quaternary rlmmonium chloride, and filtration was shown to adeqrrately control all these factors. This combination has not previozrsly been used as a water treating technique. Evaluation tests of the water conditioning system prior to injection are described, and results of such tests are presented. Control measures needed to insure a continusously adequate water treatment are reviewed. INTRODUCTION The utilization of sea water for waterflooding has only recently been attempted. Knowledge of treating requirements has been limited, and in most cases no water treating has been done. Prior to the initiation of the Third Grubb zone pilot water flood at Ventura, Calif.,1,2 extensive laboratory research was done in an effort to define the treatment necessary to provide a suitable injection fluid. Close coordination and cooperation between field and research personnel were found to be the foremost requisites in developing the most economical and practical method for treating ocean water. LABORATORY STUDIES Plugging Tendencies of Untreated Ocean Water A program of laboratory studies was initiated for the purpose of evaluating whether ocean water could be injected into the formation for prolonged periods of time without causing plugging of the pore spaces of the formation. Because of the fairly low permeability of the formation (averaging about 40 md), it was realized from the outset that a water of exceptionally high quality was needed. Ocean water used in the laboratory studies was carefully filtered through ultrafine fritted glass filters, having nominal maximum pore sizes of 1.4 microns. Permeability tests were then performed on representative core material from the formation. It soon became apparent in these tests that filtration alone was not a sufficient treatment for the ocean water. Prolonged injection of the filtered water caused rapid plugging of the core samples. The permeability decline of a typical sample is illustrated by Curve A in Fig. 1. The several factors which can contribute to this plugging tendency are briefly reviewed below: Interaction with Formation Clays An evaluation of clay swelling effects on liquid permeability was made using core samples from the Grubb formation. An oil was chosen for determining the reference liquid permeability because it would not tend to react with any clays that might be present in the formation. The samples were then extracted, dried, and resat-urated with either treated ocean water, formation water, or fresh water. Permeabilities to the various waters were then determined. Results of this test series are summarized in Fig. 7. The difference between the oil permeability and water

Jan 1, 1957

By George A. Lamb

AMONG the main interesting developments in the coal market have been the changes that have taken place between the consumer groups. Important signs of these changes began to appear many years ago, but in a modest way, and were apparent only to the few fuel experts making broad statistical determinations. It is doubtful, however, that any of these experts appreciated the significance of their early findings, and perhaps none had the imagination to consider how extensive these changes might be eventually with respect to solid fuels sales and distribution. (Reference here will be principally to bituminous coal.) Railroad Fuel Major changes in coal use did become pronounced after World War II, and it did not take an expert to see what was taking place and how serious the impact was likely to be. First, was the case of the steam and diesel locomotives. The railroads had been considered the best coal customers; they were steady and large purchasers and usually paid a better price than most others. Railroad fuel provided the basic mine realization and it often was the source for operating cash during general market slumps. It was the outlet for 20 pct of the bituminous coal production, as much as 110 million tons in 1946.

Jan 2, 1957

By S. C. Geol, C. H. Page

INTRODUCTION Mining at Mindola Mine, Rokana Division of Nchanga Consolidated Copper Mines Limited is the deepest on the Zambian Copperbelt. Mining extends to 1150 metre depth so far and the present plans extend to 1500 metres, although reserves exist below this level. Mindola Mine is the major producer of copper/cobalt ore at Rokana Division and produces approximately 200,000 tonnes of copper/cobalt ore per month. A standard open stoping method is the only method used for mining with minor variations in positioning drilling drives and other development, figure 1. The standard main haulage interval is 75m but in flat dipping areas the full stope height is split into two or three panels. In 1970 severe mining problems were experienced when mining deeper than 850111 below surface. The main problems included: - Heavy support requirements in drilling drives near stope face. - Premature closure of blast holes necessitating pre-charging of the holes with explosives immediately after drilling and well before the day of blasting. - Severe bumping and spitting due to rock movements on drive surfaces and remotely within the rock mass under high stress. - Low mining efficiency due to dilution from the waste hangingwall. - These stress related factors also caused some premature detonations of precharged but unprimed blast holes which became a serious safety hazard. A number of alternatives have been considered to overcome these problems. A search for leas sensitive explosives to avoid the premature detonation problem has been partially successful, however, the need for a method of reducing stress levels at the mining face is still considered essential as the mine goes deeper. This paper describes experiments with Regional Support Pillars as a method of reducing stresses at the mining face.

Jan 1, 1981

Geologist or Mining Engineer who has had sufficient experience to make examination of a large area and who can report upon economic value of any minerals found. Work will extend over a period of 2 or more years. Location, India. R-1660. Assistant Superintendent of malleable and gray iron foundry, young man. Must have thorough molding experience, especially on squeezers, knowledge of mixture control and operation of air furnaces, cupolas, and annealing ovens college graduate preferred. R-1727. Engineer thoroughly familiar with distilling, evaporating and drying machinery. Capable of taking charge of entire evaporator department, including engineering and selling. New Jersey. R-155C. Experimental Draftsman familiar with small automatic mechanisms, principally those produced in large quantities by punch-press methods, such as adding machines or typewriters. New York City. R-1566. Patent Draftsman.-At least 2 years' experience on perspective rend-ering of small automatic machinery. New York City. R-1570. Designer.-Familiar with hydraulic work and capable of going ahead with detail and design work without supervision. Pennsylvania. R-1575. Superintendent or Foreman. Knowledge of ceramics, clay products, electric porcelain, tile, factory materials, etc. New York State. Good salary to right man. R-1578. Designer. Experienced in designing mining machinery, including electric hoists. Canada (Quebec). R-1589. Construction and Operating Superintendent. Executive and thor-oughly experienced in the zinc melting industry. Will have charge of construction of plant and its operation. Salary $6000 to start; increase to $8000 later. India. R-1593.

Jan 11, 1919

By C. A. Wright

Since the adoption by the U. S. Bureau of Standards several years ago of specifications for standard 100- and 200-mesh sieves, frequent requests have been received that this Bureau test and certify sieves of other sizes than these. With a view to the adoption of a series of standard testing sieves which might be of use to all industries making fineness tests, this Bureau for two years has been studying the question of such a standard screen scale. Various scales that have been proposed were considered, and information was sought of representative firms in the various industries interested as to their requirements. Manufacturers of sieves have also been consulted as to the desirability of different screen scales and the practicability of their manufacture. As a result of this study of the question, a conference was called at the Bureau of Standards, Apr. 20, 1916, of representatives of various committees of the American Society for Testing Materials, American Society of Civil Engineers, American Institute of Mining Engineers, American Foundrymen's Association, Mining and Metallurgical Society of America, American Water Works Association, American Institute of Metals and the American Spice Trade Association; also representatives of the Committee of Revision of the U. S. Pharmacopæia, the U. S. Geological Survey, the U. S. Bureau of Mines, the U. S. Office of Public Roads and Rural Engineering, the U. S. Office of Grain Standardization and the U. S. Bureau of Standards; also representatives of a number of private firms engaged in industries in which sieves are used, such as the glass, the drug milling, the abrasive, the asphalt, the mining, the spice, the chemical, and the graphite industries; also representatives of the firms in this country manufacturing wire cloth and sieves. This Conference, after considering the various screen scales either proposed or now in use, adopted as a Standard Screen Scale that given in Table 1, and recommends that it be adopted generally by scientific,

Jan 1, 1918

By Chris Mills

The role of gravity separation in the mineral industry is briefly considered in perspective. The mineralogical and laboratory approaches to gravity process design are examined with emphasis on process technology selection. The equipment available for small scale and pilot test-work is discussed, particularly in regard to scale-up and the acquisition of reliable, accurate data. Transposition of performance data from pilot scale to plant scale is explained. The available types of full scale gravity separation equipment are discussed with emphasis on large high-capacity units. Plant layout and selection of ancillary equipment are considered.

Jan 1, 1978

By Clifford J. Lewis, James L. Drobnick

Vexed with competition from relatively high grade foreign orebodies, perplexed by marginal, low grade domestic orebodies, and ironically faced with the fact that practically every metal needed in our economy is available domestically in ample quantity in the ground, our mining industry awaits the advancements in beneficiation technology that will bridge the gap between the ground and the market place for our presently unexploited mineral reserves. Among the vast number of research and development projects underway in the metals mining industry, there are a few chemical techniques in metals winning that, with further development or wider application, could have a profound effect on the industry. These techniques include the Imperial Smelting and Refining Process for complex lead-zinc ores, chlorination and fused salt procedures, the liquid ion exchange process, and the field of non-aqueous leaching. IMPERIAL SMELTING PROCESS The Imperial Smelting and Refining Process is of interest because it offers a possible economic route for the processing of complex zinc-lead-copper ores. The process represents the outcome of the combined efforts of metallurgists and engineers of Imperial Smelting Corporation. Ltd., the United Kingdom Subsidiary of the Consolidated Zinc Corporation, Ltd., and is the subject of patents throughout the world. This process is essentially the employment of the blast furnace for the production of zinc. Zinc has always resisted blast furnace technology, primarily because of the difficulty of condensing zinc vapor from dilute gases. The Imperial Smelting Process employs a blast furnace working at ordinary pressures and in a system which is able to con- dense a blast furnace gas of a very low zinc content.

Jan 11, 1963

By Jan M. Mutmansky

The primary purpose of this presentation is to analyze the strategies available to an operator using either stripping or stripping and subsequent punch mining on a given coal property. The initial concern is the formulation of a mathematical model, which allows an operator to determine and utilize the particular highwall height, which will maximize : (1) Total profit or (2) Profit per unit of operating time. The analysis centers on the relative costs and recoveries involved in a typical coal seam amenable to stripping, augering, and punch mining. The model defines the point to which the high-recovery stripping operation with increasing overburden removal and reclamation costs should proceed before the low-recovery augering and punch mining methods are employed so that the desired objective is achieved. Examples are presented, which exhibit the use of the model on typical operations. Present mining methods as practiced in the Eastern United States are examined in the light of the results. Recommendations for improving present strategies are made and the resulting economic ramifications are analyzed. Particular attention is given to the stripping ratios presently used and recommendations for improving present mining practice are presented. Implications of these recommendations to the design of strip mining equipment are discussed.

Jan 1, 1977

By Marlin J. Veesaert

Urban quarries offer one of the greatest opportunities for profit in nonmetallic mining with limited financial risk-if properly evaluated, planned and developed to meet market needs. Location, with respect to market, is the prime consideration. Geologic considerations and quality of rock are nearly as important. Cost factors and return on investment (ROI) are the principal financial considerations.

Jan 8, 1979

By R. Hogg, D. W. Fuerstenau

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation, and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most clearly met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80% of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50% of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1973

By J. Lyndon Rosenblad

The strength of a jointed-rock mass is not well-understood. It is believed, however, that the behavior of a rock mass is governed by both the intact rock properties and the properties of the discontinuities. Rock research in the past has been concentrated on the determination of intact rock properties. Several studies are presently underway which should provide more insight into the properties of the discontinuities. Few research programs, however, have been undertaken with the intent of studying the composite rock mass behavior where either the intact rock strength or the properties of the discontinuities may control failure. There are three approaches available for studying the behavior of a rock mass, namely, field studies, mathematical models (finite element), and geomechanical models. A geomechanical model has been developed in this study where the strength and failure modes of a model rock mass are studied as a function of intact block geometry, joint orientation, joint properties, and confining pressure. The objective of this study is to gain some insight into the parameters that govern the behavior of a rock mass, which parameters are most important, and when these parameters control. This chapter describes only one phase of the study, the development of equipment for use with the rock-blocks model. The models being tested are approximately 22 x 22 x 6-in. The size varies slightly depending upon the joint orientation used. The equipment developed includes model material molds, reaction frames, loading apparatus, measuring and recording instrumentation, and other accessory equipment pertinent to the operation of a successful study. The usual problems in equipment development, such as uniformity of load application, loading capabilities, and reaction capacities are all

Jan 1, 1970

By L. M. Higgins

Dust or fume control systems are devices for capturing contaminants at their source and preventing their discharge to atmosphere. The Primary Components Of Any Dust Control System Include: An enclosure around any potential dust source such as conveyor belt transfer, crusher, screening machine, bin loading and loadout. Ductwork including hood takeoffs (transitions) to convey the collected dust laden air away from the source of dust generation to a convenient location. A dust collector for separation of particulate matter from the air stream prior to its discharge to the atmosphere. A prime mover generally a fan, to draw air into an enclosure and to overcome resistance to flow in the ductwork, dust collector and stack.

Jan 1, 1978

By A. Lawley, H. W. Schadler

TWINNING has long been recognized as a possible mode of deformation in crystalline solids and has been studied in a wide variety of crystals.&apos; Recently, deformation markings which have the topographical characteristics of twins have been seen in tungsten" and the body-centered cubic alloys of tungsten and molybdenum with rhenium.3-7 These markings have been identified as twins because: 1) they are visible after polishing and etching;2,3 2) their formation is accompanied by an audible click and a drop in load;4 and 3) the habit plane is {112}, the plane which has been identified as the twinning plane for several body-centered cubic metals.&apos; However, there has been no published evidence for the specific determination of the twinning direction in rhenium alloys of tungsten and molybdenum, because usually the deformation twins were not broad enough to be detected with a conventional X-ray beam. Consequently, [111] is inferred as the twinning direction since the latter must lie in a plane of symmetry perpendicular to the twinning plane (112). As Sims and Jaffee3 and Lawley and Maddin4 have shown, the addition of rhenium to molybdenum and tungsten increases the ductility of the alloy over that of the pure metal, but twinning is much more profuse in these alloys than in the pure elements, particularly at Mo-35 pct Re*and W-30 pct Re. Since twinning is often associated with brittle fracture in iron8 and the silicon-irons,9 direct experimental proof that the deformation markings in tungsten and molybdenum alloys of rhenium are twins seemed to be needed. Using the Laue back-reflection technique, the deformation markings in a Mo-35 pct Re alloy are shown to be deformation twins. The twins have a (112) habit plane and the twinning direction is <111>. The Mo-35 pct Re specimen used was taken from a 0.060-in. zone-refined single crystal deformed 6 pct in tension at 78°K. The Laue back-reflection technique, with a film to specimen distance of 2 cm, and white radiation from a copper target were used.

Jan 1, 1962

TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen: - I herewith present a report of some. of the more important activities of the Institute for the year of 1922. The outstanding feature of the year is the optimism felt by our members despite the continued depression in the mining industry. January 1, 1921, found many of our members out of employment or drifting into other industries to tide them over the depression, but almost universally the feeling has been that this was but a temporary condition and that sooner or later the necessary production of raw materials would enable these members to return to their former activities and renew their participation in Institute affairs. As the year passed conditions improved and, before it ended, many had found employment in their previous occupations. Bearing in mind that this depression has been very real, we have reason to be well satisfied with the work that the Institute has been able to do. The loss of members through inability to pay, dues has been large, and income has been correspondingly reduced, but it proved to be materially in excess of that anticipated early in the year, so that a substantial and unanticipated balance was carried forward toward the activities of 1923. PUBLICATIONS Following the example of other technical societies, and to conserve our resources, no Year Book was published in 1922. The lack of an up-to-date membership list for the use of our members was regrettable, but the saving of $5000 proved to be worth while. During the year, Volumes LXV, LXVI, and LXVII were printed and sent to members. These volumes were composed largely of the papers of 1920 and 1921, publication of which had been delayed partly through lack of funds and partly for the purpose of segregating into volumes those papers dealing with the same general subject. The segregation of papers had been suggested by a number of members who had advised that they were not primarily interested in all subjects

Jan 1, 1925