Search Documents

By M. J. Marcinkowski, Gordon E. Lakso

An extensive investigation has been made of the deformation behavior associated with the Fe3Si super-lattice using transmission electron microscopy techniques. Above 243°K the stress-strain curve exhibits three stages. Stage I occurs at a very low stress level and is related to the generation of perfect superlat-tice dislocations. Stage II is characterized by an extremely rapid rate of work hardening and is associated with the Taylor type locking of these superlattice dislocations. Finally Stage III is related to dynamic recovery processes since the work hardening rate is very small. Below 243ºK, only Stage I is observed, but it occurs at a much higher stress level. This latter observation is related to the generation of imperfect dislocations in Stage I with the consequent production of second nearest neighbor antiphase boundaries. The reason for this is that insufficient thermal energy is available at these low temperatures to generate the complete and perfect superlattice dislocations. It has been shown that the fully ordered FeCo alloys, i.e., those possessing the B2 type structure, exhibit three distinct stages of work hardening whereas the corresponding disordered alloys show only one.&apos;" This difference in behavior between the disordered and ordered alloys has been attributed to the fact that dislocations in the former case travel only as ordinary 1/2ao(111) types whereas in the latter case the move through the lattice as coupled 1/2a0(111) dislocations separated by an antiphase boundary (APB), i.e., the so-called superlattice dislocation. Although some preliminary work has been carried out concerning plastic deformation in ordered alloys possessing the DO3 type superlattice,3 no detailed analysis similar to that described in Refs. 1 and 2 has been attempted. Specifically, it has been suggested that the superlattice dislocation in this particular type structure should consist of four ordinary 1/2ao<111> types bound together by first and second nearest-neighbor APB&apos;s. Fe3A1 and Fe3Si are the two classic alloys possessing the DO3 type lattice; however, because of the somewhat higher ordering energies associated with the FesSi alloy, which in turn assures that dislocations will travel through the lattice as perfect superlattice dislocations under at least some conditions, it was chosen for the present investigation. Because of the extreme brittleness of Fe3Si, all deformation was done in compression. Stress-strain curves were obtained using both polycrystalline samples as well as single crystals. In the latter case the crystals were oriented so that deformation could be controlled either by single or double slip. They were then wafered parallel to and at various angles to the operative slip planes. These wafers were in turn examined by transmission electron microscopy (TEM) techniques in order to determine the extent of the interaction from the dislocation configuration contained therein. EXPERIMENTAL PROCEDURE The alloys used in this investigation were arc melted under helium from electrolytic iron of greater than 99.90 wt pct purity and transistor grade silicon of 99.99 wt pct purity. A typical analysis of interstitial impurities showed 120 ppm 0, 15 ppm N, and 65 ppm C Because of the extremely low ductility of the Fe3Si alloys, it was necessary to spark cut 0.230-in. diam polycrystalline cylinders 0.400 in. long from arc-melted fingers using a thin-walled brass tube as a cutting tool. The polycrystalline alloys could not be recrystallized since very little strain was induced in preparation. However they were annealed at 1273°C for 15 min in evacuated vycor capsules to relieve any cooling stresses that may have developed during solidification and then air cooled. The resulting grain size of the alloy was 0.50 mm. According to warlimont4 1273ºC is just within the single phase field where FesSi possesses the DO3 type lattice. In addition because of this high critical ordering tem-ature, air cooling from this temperature was believed sufficient to fully order all of the Fe3Si samples used in the present investigation. For the same reason, no attempt was made to achieve any degree of disorder by quenching. In fact, rapid quenching from 1123°K caused cracking. Such cracking was first suggested by sato5 with respect to the experimental observations of Glaser and Ivanick.6 Single crystal compression specimens were spark cut from single crystal ingots grown in a Bridgman type furnace. The iron and silicon for the crystals was prealloyed by arc-melting two 130-g buttons which were cut into small pieces before remelting in the furnace. This procedure resulted in a long-range inhomogeneity of 0.5 at. pct Si between the top and bottom of the 2-in.-long single crystal ingot, which was assumed to be negligible in the present investigation. The single crystals, after orienting and spark-cutting, were about 0.37 in. by 0.37 in. in cross section and about 0.5 in. long. True stress-strain curves were obtained using an Instron Tensile Testing machine in conjunction with techniques described previously. 1,7 The strain rate was 0.05 in. per in. per min. Prior to testing, the ends of all the compression cylinders were hand polished using a special jig to insure parallelism after which the sides of the samples were electrochemically polished to eliminate stress risers and to facilitate slip line observations. Test temperatures between 77" and 823°K were obtained using various cooling and heating media as described in Ref. 7 while at the upper end of this temperature range, a mixture of equal

Jan 1, 1970

By David B. Brooks

Identified potential resources of lead and zinc are lower, relative to reserves, than the same ratio for other metals, Either there is little material below present grades or, if it exists, there are no data on it. The author examines both these factors in detail, and also introduces a third possibility. In their 1961 monograph, The Future Supply of the Major Metals, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.&apos; Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vast quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.&apos;12 This situation, which they called "the lead-zinc anomaly&apos;&apos; has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative. There are at least two reasons for devoting time to the lead-zinc anomaly. First, while it is unlikely that we shall have to turn to alternative lead or zinc resources in the near or middle-term future, the longer run resource picture for the two metals is not so certain.3 Both within the United States and for the world as a whole, new discoveries will have to come at a fair pace to keep up with growing rates of consumption. Thus, it is important to see whether there exist lower grade or nonconventional potential sources of two such useful metals that we could turn to at some time in the future. The second reason for studying the lead-zinc anomaly is also related to resource adequacy, but is of more general significance. Depending upon whether the anomaly is technologic, geochemical, spatial, or temporal in origin, we shall be able to draw some conclusions about the resource picture for other metals. Can we expect the apparent pattern of lead-zinc resources to be repeated? If so, will technologic advances in either exploration methods or mineral processing be able to alter the pattern? Or is the pattern unalterably set by geochemical distribution? Most important, are metals characterized by what seems to be an anomaly, different in any way from metals for which low-grade or nonconventional sources already have come to be exploited, as the porphyry deposits have for copper. In sum, investigation of the lead-zinc anomaly represents a case study combining both physical and economic aspects that may open up a neglected area in evaluating mineral resource adequacy. WHAT IS THE LEALLZINC ANOMALY? There are two dimensions to evaluations of the potential of any mineral resource? The first involves the degree of certainty that we ascribe to the estimate: how much do we know about the size of the resource as a result of geological mapping, exploration, and mine development? This dimension is expressed by the terms measured, indicated, and inferred reserves (and, if you wish, &apos;undiscovered reserves&apos;), all of which terms carry with them the implication of exploitability under current cost-price conditions. The other dimension to evaluations of a mineral resource involves the economic limits of the estimate: how will the size of the resource vary with different (usually more favorable) cost-price conditions? (This economic dimension should be understood broadly to include all factors bearing on the cost-price relationship. In this sense it subsumes technology because any resource is exploitable at some cost; the role of technology is to bring cost down.) The latter dimension is expressed in the terms potential or sub-marginal &apos;ore,&apos; and is logically quite independent of the former. For example, we have relatively good measurements of the tonnage of manganese in low-grade deposits in this country, though they are too lean to be considered reserves; on the other hand, we are much less certain of our measurements of new lead and zinc deposits in Missouri, though there is no question but that there is a sizable reserve. Thus, it may be uncommon but is not a contradiction to talk of measured submarginal ore or inferred potential ore.

Jan 1, 1968

By Martin F. Littmann

Inclusions of MnS and Fe3C have been introduced into single crystals of 3 pct Si-Fe to study their effects on recrystallization behavior and textures after cold rolling and annealing. The presence of MnS in (110) [001] and (111)[112] crystals inhibited primary grain growth and promoted secondary recrystallization but did not alter the texture significantly after annealing at 1200°C. The presence of Fe3C in (llO)[OOl] and (100)[001] crystals caused a refinement of the primary re crystallized grain size but did not promote secondary recrystallization. THE texture behavior of single crystals of 3 pct Si-Fe during deformation and recrystallization has been studied by numerous investigators. The early work of Dunn&apos; followed by Decker and Harker2 involved relatively small cold reductions. More detailed studies of Dunn3&apos;4 and of Dunn and Koh5&apos;6 involved a reduction of 70 pct and recrystallization at 980°C for several crystals. Walter and Hibbard7 studied a greater variety of initial orientations and sought to relate the textures to those of polycrystalline material. Attention was focused on the nucleation process during early stages of annealing and on surface energy effects in studies by Walter and Dunn8 and by HU.9&apos;10 One of the most extensive investigations has been reported by T. Taoka, E. Furubayashi, and S. Takeuchi.11 Most of this work has been conducted using relatively pure crystals with minimal amounts of precipi-tate-forming elements such as carbon, oxygen, sulfur, and nitrogen. Recently, however, S. Taguchi and A. Sakakura have observed that AIN precipitates can alter the recrystallization textures of rolled (100)[001] crystals.12 The present studies were initiated to determine effects of MnS and Fe3C precipitates on recrystalli-zation and grain growth behavior of rolled single-crystals of 3 pct Si-Fe. Both of these types of inclusions play significant roles in the recrystallization behavior leading to the formation of the (110)[001] or cube-on-edge texture in commercial grain-oriented silicon iron. It is well known that (110)[001] primary grains are formed by recrystallization of (110)[001] or (11 l)[ 112] crystals after cold reduction of about 60 pct or more. Crystals of these orientations, therefore, were selected for study of the effect of MnS in-clusions on grain growth. On the other hand, a major component of the texture of cold-rolled, polycrystal-line 3 pct Si-Fe is the (100)[011] orientation. The function of Fe3,C inclusions is of interest for this orientation. EXPERIMENTAL PROCEDURE The single crystals used are listed in Table I and were obtained from commercial Si-Fe alloy processed to produce (110)[001] and (100)[001] texture by secondary growth. The cube-on-edge material was 0.59 mm thick. Suitably large (110)[001] crystals 25 mm wide were selected and their orientations were determined using an optical goniometer. Etch pits for texture determination were formed by a ferric sulfate solution. The other crystals used in the study with (100)[001], (100)[011], and (111)[112] orientations were obtained from sheet which contained large grains developed from secondary recrystallization by a surface-energy driving force.13 Most crystals had a (100) plane very nearly parallel to the sheet surface and the rolling direction could be selected readily. The same sheet also contained a few crystals with (111) planes parallel to the sheet surface, these also being a result of growth by surface energy. The crystals selected from the sheet were about 25 mm wide and 0.25 to 0.28 mm thick. As shown in Table 11, the crystals already contained about 0.070 to 0.10 pct Mn. Inclusions of MnS were incorporated into crystal 36 in the following manner. The crystals were first sulfurized by holding them Table I. Initial Orientations of Crystals Crystal No. Initial Orientation Thickness, mm Special Treatment 34 (I10) [00l]* 0.59 None 36s (110) [001] 0.59 Sulfide precipitates added 30,40 (111)[Ti21 0.28 None 43s (III) [Ti21 0.28 Sulfide precipitates added 37 (100) [Oll] 0.30 None 37C (100) [01I] 0.27 Carbon added 41 (100) (01I] 0.25 None 41C (100) [OI11 025 Carbide precipitates added 42 (100) [OOl] 0.25 None 42C (100) [001] 0.25 Carbide precipitates added *Tilted 4 deg to r~ght about R.D. Table II. Compositions of Crystals Special Treatments Base Analysis ~ ______________________£________________Crys- Crystals Pct Si Pct C Pct Mn Pct S Pct N Pct Al tal Pct C Pct S 34.36 2.93 • 0.099 <0.005 - 0.0014 36S 0.011 30.37 to 42 2.78 0.0057 0.070 0.001 0.0008 0.0011 43S 0.022 37C 0.029 -41C 0.028 -42C 0.026 *Estimate 0.004 pct. Oxygen estimated <0.003 pct on all samples

Jan 1, 1970

By AIME AIME

The following changes of address of members have been received at the Secretary&apos;s office during the period of Mar. 1 to May 1, 1908. This list, together with the list in Bi-Monthly Bulletin, No. 20, March, 1908, therefore, supplements the annual list of members corrected to Jan. 1, 1908, and brings it up to the date of May 1, 1908. The names of Members who have accepted election during March and April, 1908 (new members), are printed in italics., By a simple method of cutting out these names and addresses, and pasting them directly over the corresponding names in the annual list of members, the record can be kept practically up to date and the value of the list correspondingly increased. For this purpose the changes of address have been printed only on one side of the page. The names of new members, being in italics, are readily distinguished from the others, and can be pasted in approximate alphabetical order on the margins of the pages of the list.

Jan 5, 1908

[MINING AND EXPLORATION DIVISION Established as Mining, Geology and Geophysics Division, Sept. 27, 1949 Name changed February 19, 1958. Lyman H. Hart, Chairman Robert J. Lacy, Assistant Chairman Vice Chairmen: John C. Wangaard, Membership J. M. Ehrhorn, Program John G. Hall, Publications C. E. Nelson, Secretary American, Smelting and Refining Co. 120 Broadway New York 5, New York Editor, Rock-in-the-Box: J. W. Chandler.]

Jan 1, 1961

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Mining engineer and geologist. Member. 29 years old. Married. Seven years&apos; experience in Lake Superior iron district; two as superintendent of extensive exploration in new fields. Capable of handling all details of the exploration and development of new properties. Available now. No. 431.

Jan 2, 1918

By J. L. Giove, J. M. Hodge, R. G. Storm

The hardenability effect of molybdenum has been evaluated by a number of investigators, including one of the present authors.1,2,3,4,6 Considerable discreMncy exists, however, among the results of these various investigators, and two of them, Brophy3 and Kramer,4 have indicated that the apparent hardenability effect of molybdenun would vary, depending upon the other alloying elements in the steels being considered. The results of previous, unpublished work conducted at the Duquesne Works Laboratory of the Carnegie-Illinois Steel Corporation also have indicated significant differences in the hardenability effect of molybdenu~n in nickel and in chromium steels. The present investigation was undertaken in an effort to establish the mechanism governing this difference in the hardenability effect of molybdenum. This work involved both end-quench hardenability and isothermal transformation tests on two series of steels of varying molybdenum content. One steel contained 3 pct nickel and the other 1 pct chromium. It was hoped that such studies would shed further light on the mechanism of this behavior. Materials and Experimental Work MATERIALS The chemical compositions of the steels used in this investigation arc shown in Table 1. These steels were furnished by Battelle Memorial Institutc in the form of 100-lb induction furnace ingots. The top half of each ingot was forged to 1 3/8-in. square billets and then rolled to I-in. round bar stock for isothermal transforma- tion studies. The bottom half of each ingot was forged into approximately 1 1/4-in. rounds for end quench tests. All of the steels were normalized from 1650°F and tempered at 1100°F before nlachming to end quench or isothermal samples. END-QUENCH TESTS standard l-in. diam end-quench tests were made on each of the steels. The test bars were austenitized at 1600°F for 30 min,, quenched in a standard Jominy jig, and hardness surveys were made in all tests. The 95 pct martensite point was deterInined from hardness values5 and cheeked by metallographic examination. The jominy distance values for 95 pct martensite were converted to hardellability values in terms of ideal diameter (Dl), using a revised carve for the relationship between Jominy distance and ideal diameter. This curve was based on the cooling time from the A1 to the bainite nose temperatures rather than on the usual criterion of half-temperature time. The cooling rates as determined by Russell and Williamson9 were used as a basis for this relationship. The derivation of this curve is described in detail in the appendix. ISOTHERMAL TRANSFORMATION STUDIES Samples for the isothermal transformation studies were quarter sectors of 1/16.is-in. thick slices from the 1-in. round bars. All samples were austenitized for a total the of 15 min., transferred rapidly to a lead bath for isothermal transformation, and brine quenched from the lead bath. A time of 3 see was allowed for the sample to come to the temperature of the lead bath, and this time was not included in the isothermal transformation times. Each sample was examined metallo-graphically at a magnification of 100 diam. The per cent transformation was estimated by comparison with standard micrographs, and the values were plotted against the on log/log coordinate paper. At least 4 and as Inany as 10. points were plotted for each steel. A line was drawn through the points for each steel, and the times for 5 pct transformation were obtained from the plot for each steel. Isothermal transformation diagrams in terms of 5 pet total transformation, covering the temperature range of 800 to 1200°F, were determined in this manner for an austenitizing temperature of 1600°F. The times for 5 pct transformation at the bainite nose for austenitizing temperatures of 1800 and 2000°F were also determined in the same manner. These times for 5 pct total transfor-

Jan 1, 1950

Since the beginning of the 20th century the world has been trying to find a new political system, even as it did at the end of the 18th century. The French Revolution instigated the destruction of absolute monarchies when Napoleon unwittingly showed the masses the advantages of freedom, as opposed to the abuses of unlimited power by the imperialists. In spite of advances in culture, science, and technology during the past 50 years, there is a hangover of laissez-faire economic principles. Failure to divert the trends of minority pressure groups has caused two world wars and is the basis for the current social unrest and turmoil. In the ebullition of ideas there have risen to the surface the dregs of ideas, old and new-Nazism, Fascism, Russian Communism-a hodgepodge of imperialistic, socialistic, communistic and capitalistic maneuverings where state monopoly of capital enables ruthless exploitation of the masses. The United States owes much of its industrial greatness to the work of pioneers in the mineral industries. The task of the pioneer was to locate and develop in a rude way the mineral resources of the nation. Today, mineral industries leaders are still in great demand, but for a different purpose-to direct intelligent utilization of the limited, waning, submarginal mineral resources. Today the need is for trained earth scientists, mineral

Jan 1, 1950

By J. J. Casey, R. S. Busk, D. L. Leman

The mechanical properties and the phase-temperature relationships of magnesium-lithium-aluminum, magnesium-lithium-zinc, and magnesium-lithium-aluminum-zinc alloys are presented. It is shown that the strengths of some of these alloys can be tripled by heat treating and aging but that the high strength is accompanied by brittleness and lack of stability. MAGNESIUM-LITHIUM alloys are interesting because the hexagonal structure of magnesium can be changed into the more ductile and workable body-centered cubic structure by the addition of only 10 pct lithium.1 After Loonam2 determined that the ductility of the magnesium-lithium alloys is destroyed by even trace quantities of sodium, it was possible to prepare ductile alioys and study their mechanical properties. Jackson3 and coworkers have ably described their results with both the binary and polynary magnesium-lithium alloys. The present paper is a report of the mechanical properties of wrought magnesium-lithium-aluminurn, magnesium-lithium-zinc, and magnesium-lithium-aluminum-zinc alloys. Experimental Procedure The alloys were made by melting 7 lb of magnesium in a steel crucible under a molten flux of 75 pct LiCl + 25 pct LiF3 previously dried at 1600°F. The metal was heated to 1300°F for alloying aluminum and zinc and then cooled to 1250°F for adding lithium (sodium content: 0.01 to 0.04 pct). After the lithium had been alloyed, dry LiF powder was sprinkled on the melt to thicken the excess flux. After a 15 min holding period, the flux was skimmed off. Paraffin vapors were used to protect the metal as it was poured into 3 in. diam by 11 in. long magnesium molds. Billets were extruded into 3/8-in. diam rod and 1/16 x 3/4-in. strip; sheet was prepared from 1/8x 7/8-in. extruded strip, first by hot rolling and then by cold rolling 2 pct per pass. Hot rollability, or the temperature range through which the alloys could be rolled, was determined by rolling the strip two passes at 30 pct reduction per pass. Cold rollability, or the percentage of cold reduction to cause detrimental cracking, was determined on 0.064-in. hot-rolled sheet. Standard ASTM procedures were followed to obtain the mechanical properties, using 0.2 pct offset for the yield strengths. The level of properties produced with commercial magnesium alloys using the procedure described is given in a previous publication." Results Magnesium - Lithium - Aluminum System: The good workability of magnesium-lithium alloys is illustrated by the data in table I, which shows approximately how the extrusion pressure decreases as the amount of cubic phase increases. Binary magnesium-lithium alloys are soft and weak, but aluminum raises their strengths con-

Jan 1, 1951

L. D. Ricketts, New York, N. Y.-In recent years the metallurgical field of the copper industry has expanded greatly, the copper ores have become lean and diverse in character, and we are obliged to treat such ores on a very large scale. On the commercial side, the operating and consulting staffs of ,the great mining companies have been enlarged and organized, and no great capital expenditure is decided upon until it has been investigated and recommended by a highly organized force of specialists as a committee. I believe that in the scientific field and in the most valuable proceedings of our various societies the old idea of one-man point of view and one-man treatment of principle and detail together has been. splendidly developed and should continue, but for the advancement of our art we should deliberately discuss subjects among ourselves in order to do away with the idiosyncrasies of the individual and to gain a composite view representing the best thought of many men. In the development of new ideas leading to the introduction of new methods, the societies could enlarge their present great field of usefulness if such discussion be had, and in my opinion further great good could be done if a number of men of different qualifications and experience would join in preparing a joint book, each dealing with his particular problem, but consulting the other men. In this way individualism would be preserved and various processes would be described, and if properly reviewed the paper would be palpably capable of analysis, and the student would have at his command the associated efforts of a group of qualified engineers.

Jan 4, 1915

By L. A. Wood, A. G. Winslow

Subsidence has occurred in several areas of the upper Gulf Coast region of Texas, although in most cases this is not evident without precise instrumental leveling. As referred to in this report, the region comprises about 7200 sq miles of the Gulf Coastal Plain and includes all or parts of the following counties: Harris, Fort Bend, Waller, Brazoria, Galveston, Liberty, Chambers, Orange, and Jefferson (Fig. 1). Topographic relief is low, ranging from sea level at the Gulf of Mexico to 300 ft or more in northwestern Harris County. In this upper Gulf Coast region, which embraces the most heavily populated and industrialized parts of Texas, industrial and municipal water supply is obtained chiefly from wells. Largest center of ground-water withdrawal is the Houston-Baytown area, where about 200 million gallons per day was pumped in 1956 for municipal and industrial use. Other large centers of ground-water withdrawal include the Alta Loma sector and the heavily industrialized Texas City area in Galveston County, where about 23 mgd was pumped in 1956. In the Freeport area in Brazoria County about 6 mgd was pumped in 1956 for city and industrial supply. In addition to withdrawals in metropolitan districts, great quantities of ground water are supplied by irrigation wells to thousands of acres of rice. These wells are widely dispersed over many miles, principally in Harris, Waller, Fort Bend, Brazoria, and Liberty counties, and effects of pumping are not so readily noticed as in the industrial and metropolitan sectors. Subsidence: Starting with the 1905-1906 line from Smithville, Tex., to Galveston, the U. S. Coast and Geodetic Survey has extended a network of first and second-order level lines throughout the upper Gulf Coast region. In 1918, when a line was run from Sinton, Tex., to New Orleans, La., a tie was made to the 1905 leveling at Houston. In 1932-1933 a line was run from Palestine, Tex., to Houston, and a good deal of leveling was carried out in the vicinity of Houston. At this time the entire network was adjusted to the Sea Level Datum of 1929. In 1935-1936 and 1942-1943 several new lines were run and considerable releveling was performed. Supplementary adjustments were made after both the 1936 and 1943 levelings in order to reduce the elevations to the Sea Level Datum of 1929. These adjustments probably masked some of the subsidence that had occurred up to that time, although a certain amount of subsidence was noticed in the 1943 leveling. When several lines in the vicinity of Houston and Galveston were releveled in 1951, the regional nature of the subsidence became apparent.&apos; Direct comparison with the 1943 leveling was possible because the datum was not changed. Comparisons with prior leveling were unreliable because of differences in the early and subsequent datums. In 1953-1954 many lines in the region were re-leveled and in 1957 the entire network, including the elevations previously determined, was readjusted to determine the changes in elevations as indicated by various levelings between 1905 and 1953-1954. In this instance the adjusted elevations were held fixed near the boundaries of the region where the bench marks seem to have remained stable. The only sea-level connection held fixed was the connection of the 1905 leveling to the 1903-1906 tidal series at Galveston. Almost the entire region has been at least slightly affected by the subsidence, some areas to a great extent. The profiles of subsidence (Fig. 2) and the map showing the contours (Fig. 3) illustrate both regional and local changes. A large area of subsidence is centered in the Houston-Baytown district, where the maximum recorded is about 2.7 ft between 1905 and 1954. This probably falls short of the actual maximum, since land surface subsided as much as 2.5 ft in the industrial section alone between 1943 and 1954. Sub-

Jan 1, 1960

By E. A. Gulbransen, W. S. Wysong

THE behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotective nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance study 1,2 of the following problems. (11) the oxidation kinetics in the temperature range of 250° to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films, and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 250°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide MoO3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics. time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation The general interpretation of many of these factors has been previously discussed. LITERATURE The oxidation of molybdenum has not been studied critically. Although" many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Culbransen 4 Their results showed that MoO2 is the oxide which is stable in contact with the metallic subgtrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Mo03 is no longer observed, Mo02 being the only oxide found. Hagg and Magneli5 have shown from an X ray study that the a-phase, orthorhombic MoO3 is stable up to 1050°C. Two other phases, ß and ß&apos;, with compositions close to Mo02 90 are also obtained The formula for the ß phase is not given but that of the ß&apos; phase is defined as Mo9026. The ß&apos; phase is found to be built upon a monoclinic unit cell. A -?-phase is isolated from a preparation M00275 heated for 17 hrs at 670°C. This phase is

Jan 1, 1947

HARD as it is at any time to provide more than three million tons of coal each year for power plants, the task really gets rugged in the wintertime when the fuel freezes solid in the cars. At the Marysville plant of the Detroit Edison Co. the problem of unloading cars of frozen coal was severe because there was an unloader over only one of the two tracks in the coal unloading house. Moving downward by their own weight, with no driving force to aid them, the spuds of this old unloader were unable to break through the crust on a frozen coal car. 20,000 Lb Force To meet this problem, a new mechanical car unloader was installed over No. 2 track and placed in service in December 1947. It is a Kenney type unloader built by Heyl & Patterson, Inc. of Pittsburgh, Pa., a modification of equipment originally designed to unload iron ore cars. The major advantage of this unloader is the force with which it can drive the sharp spade on the end of its ram down through the pockets of a frozen coal car. The unloader consists of the following major units: 1. A traveling bridge structure. 2. A traveling trolley. 3. A retractable and oscillating ram. 4. The operators cab and controls. The bridge is provided with safety hooks to prevent its being lifted from the rails by the upwards push of the ram. The bridge will travel 190 fpm and has sufficient traction on its four wheels to move three loaded 70 ton cars. The trolley runs on tracks supported by the bridge girders and also has upper tracks to control the push from the ram. Two of the single-flange trolley wheels are driven by a one and a quarter hp dc motors equipped with magnetic brakes. The ram is raised and lowered by a 20 hp dc motor equipped with a magnetic brake. A full stroke of a little over 14 ft is given the ram through its rack and pinion drive and the spade can be pushed down into a loaded car with a force of about 20,000 lb. A 15 hp dc motor with a magnetic brake is applied to this drive and is able to swing the ram 45º either side of the vertical. The usual procedure in emptying a coal car is first to drive the sharp spade down through the coal until the pocket is opened and the coal starts to run out the hopper. When all the hoppers are open, the sweeping action of the ram and spade is used to move the remainder of the coal in the car over to the open hoppers. The travel of the trolley permits cleaning the sides of a coal car with the edges of the spade, using the sweeping motion of the ram. It is still necessary to clean out the corners of the car by hand. Final Clean-Out This unloader was a new development and there were improvements to be made before it was completely satisfactory, such as reduction in speed and conversion to ac drive motors. However, it helped at Marysville and unloaded many frozen cars that would have taken a lot of heating to thaw out enough for the old unloader to handle. The mechanical coal unloader described above was a considerable improvement but still left a job to be done by hand-the final cleaning out of the coal cars. The ram had the ability to open a hole through the hopper cars, but did not meet required unloading speed. To eliminate hand cleaning a car shakeout, manufactured by Hewitt Robins, Inc. was added to the installation. This equipment is used to clean the coal car out after the unloader has provided an

Jan 1, 1952

By E. O. Wagner, V. F. Parry, W. S. Landers

Following investigations by the Denver Bureau of Mines on drying fine coal in the entrained state, Texas Power & Light Co. employed the fluidized technique to upgrade Texas lignite for use in power plants. Because of the rapidly rising cost of natural gas in Texas the company agreed to cooperate with the Bureau of Mines in studying further the upgrading of lignite by low-temperature carbonization, since potential value of the tar would help off- set the cost of fuel. Considerable interest was aroused, therefore, when Aluminum Co. of America decided to use dried lignite in its 240,000-kw power plant at Rockdale, Texas, operated by Texas Power & Light. Carbonization of coal before burning in a power plant is not new. Plants in Germany have been operated for many years on carbonized brown coal and lignite briquets produced in large integrated plants. Large-scale experiments in carbonizing pulverized coal with hot flue gases were made 30 years ago at Milwaukee, and many inventors have proposed other processes. In the U. S., technical and economic problems have prevented successful operation of large plants on carbonized coal, but new techniques of handling solids in fluidized beds may overcome these difficulties, particularly if the higher volatile noncoking coals are used.

Jan 1, 1956

By Elmer W. Pehrson

THE founding of the American Institute of Mining Engineers in 1871 came at an unusually significant moment in the life of our country. The industrial revolution, in which mineral production played a major role, was just getting underway. The iron industry, established several decades earlier, was reaching sizable proportions. In 1871 pig-iron production was approaching 2 million tons, and the industry had spread as far west as Missouri and Wisconsin. The chief sources of iron ore were Pennsylvania, New Jersey, New York, and Michigan. The age of steel was in its infancy; production had not yet reached 100,000 tons per annum. The gold rush to California two decades earlier and the discovery of other gold and silver bonanzas in the West paved the way for the transcontinental railways, which were then being built and which contributed much to the subsequent development of the great copper, lead, and zinc districts of the Rocky Mountain area. Regular production of copper in the Michigan peninsula and of lead in Missouri and the upper Mississippi region had been established for many years but on a scale dwarfed by the quantities later required as technical progress, invention and enterprise made possible the rapid expansion of industry. Discovery of oil in Pennsylvania in 1859, the growing recognition of the

Jan 1, 1947

By D. H. Newland

CERTAIN observations from the field and laboratory suggest the need for recasting some of our ideas about gypsum as a rock-forming mineral and in relation to supplies for industrial use. Until about 25 years ago, the use of gypsum was confined almost entirely to agriculture. During the past quarter century, though, its usefulness has been greatly developed, particularly in the building trades, which now absorb most of the gypsum produced. In 1919, according to the U.S. Geological Survey, the output of crude gypsum was 2,240,163 tons, a gain of 912 per cent. in 25 years. About one-half of this production was mined in New York, Ohio, and Michigan, where the proved supplies can hardly be regarded as over-large when viewed in relation to the rapid expansion of industrial requirements. The occurrence of gypsum in the United States is treated by R. W. Stone and others.1 The deposits of Canada are described by L. H. Cole.2 Several states, including Kansas, Oklahoma, Iowa, Michigan, and New York, have had special surveys made their of gypsum deposits, but the reports, as a rule, refer to conditions as they existed from 15 to 20 years ago.

Jan 9, 1921

By Willard R. Jillson

Within the last ten years Kentucky has become celebrated for its low-sulfur bituminous coals. Prior to this time, many investigators had discnvered the abundance of this coal but the fact was unknown to the general public until the last extension of Kentucky&apos;s mountain railroads&apos; was completed. The coals of. Kentucky are, broadly, separated into two geographic units—the eastern and the western coal fields. On a basis of their sulfur content these coal fields fall into three units, which are indicated on the accompanying map, by numbers, 1, 2, and 3. The area marked 1, the very southeastern part of the state, shows the lowest sulfur, all coals being averaged. In this field the maximum is 1.04 per cent. and the minimum as low as 0.68 per cent.—both averages and not individual analyses, which would of course show much greater variation. Included in this group are the following counties: Lawrence, 0.87 per cent.; Martin, 0.75 per cent.; Johnson, 0.73 per cent.; Magoffin, 0.87 per cent.; Floyd, 0.88 per cent.; Pike, 0.68 per cent.; Knott, 1.04 per cent.; Perry, 0.77 per cent.; Letcher, 0.80 per cent.; Leslie, 0.70 per cent.; Harlan, 0.79 per cent.; Knox, 0.86 per cent.; and Bell, 0.92 per cent. The total average sulfur content for these thirteen counties is 0.82 per cent. Bordering the restricted low-sulfur field of eastern Kentucky is the No. 2 belt (slightly darker), &apos;which is commonly known as the western border of the eastern coal field. Here the maximum sulfur is 2.91 per cent. and the minimum 1.05 per cent. Again these are averages and not individual analyses. The counties in this group are: Greenup, 2.60 per • cent.; Boyd, 1.67 per cent.; Carter, 1.07 per cent.; Morgan, 1.40 per cent.; Wolfe, 1.83 per cent.; Lee, 2.93 per cent.; Breathitt, 1.85 per cent.; Owsley, 1.09 per cent.; Jackson, 1.06 per cent.; Rockcastle, 2.30 per cent.; Clay, 1.09 per cent.; Laurel, 1.08 per cent.; Pulaski, 2.24 per cent.; Whitley, 1.05 per cent.; McCreary, 1.50 per cent.; and Wayne. The sulfur percentage average for this area including fifteen important counties is 1.65 per cent. In the western Kentucky field, the great increase in the percentage of sulfur is at once apparent. Ohio County with 3.78 per cent. is the highest and Hancock with 2.87 per cent. is the lowest. The percentages by counties is as follows: Hancock, 2.87 per cent.; Henderson, 3.22 per cent.; McLean, 3.27 per cent.; Muhlenberg, 3.31 per cent.; Hopkins,

Jan 1, 1920

By Noel W. Kirshenbaum, George A. Pouska, James M. Link

Literally millions of words have been written on the subject of mineral slurry pipelining. The sheer bulk of literature on the subject should be enough to convince the interested observer that the method is both viable and widely applied. It is the intent of this paper to examine typical mineral slurry applications. This examination should reveal the reasons that the slurry system was selected over other transport modes and it should provide a framework for determining the applicability of the technique to new projects. Slurry transport involves the conveyance of solid particles by suspension in a moving liquid. Almost any combination of solids in liquids may be imagined, and the conduit may be an open channel or a closed pipe. Historically, the most numerous slurry transport applications consisted of mineral particles in water. However, current research investigations are emphasizing other liquid carriers, specifically those which have greater economic value. Among these are gaseous and liquid fuels and chemical feedstocks. Another area being investigated involves the use of the pipeline as a chemical reactor system. The long residence time and turbulent flow characteristics of the pipeline make it particularly attractive for certain chemical reactions. Because these new systems involve a valuable liquid as well as a valuable solid, there is increased attention to solid-liquid

Jan 1, 1980

By W. B. Potter

There is probably no more interesting group of mineral fuels to be found in any country than that occurring within the limits of the new State of Colorado. The supplies are so abundant, and the occurrence and distribution are so favorable for easy development and transportation to the future manufacturing centres of the State, that they are destined to play a very important part in the material growth and prosperity of the region, the more so because of the rich and varied stores of ores awaiting metallurgical treatment, and the comparative scarcity of timber for fuel. From a purely scientific point, also, these lignitic coals form an interesting and important series. An examination of their geological occurrence and relations opens up new and important questions regarding the comparative value of various kinds of geological evidence, while a study of the character and composition of this class of fuels, which forms a connecting link, as it were, between the lignites and the true bituminous coals, may lead to a more thorough and accurate classification of mineral fuels. The analyses here presented are from samples, of not less than fifty pounds each, obtained by myself during the summer of 1875, and may be regarded as representing very fairly the average run of

By W. I. Duvall, D. E. Stephenson. Discussion by R. G. K. Morrison

R.G.K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que. Canada) - The authors have introduced a subject, the intensive study of which has awaited scientific developments. These are now such as to justify a thorough review of our thinking on the causes and control of rockbursts. The formulae developed in the paper, the comparison between rockbursts and earthquakes in figure 1 and the energy data relating to explosives serve as an effective foundation. In the paper this writer is quoted as suggesting that energy of the order of 10 x 10 11 ft. lb. may have been released in some of the heaviest rockbursts in the Kolar Gold Field. He now hastens to add that such an estimate has no scientific validity. It arises only from a casual comparison of surface and underground effects of the medium heavy bursts, referred to in the paper and estimated by Jones at 3.0 x 1010 ft.lbs., with those of obviously greater magnitude. In any case, we have the estimate by Jones above, that by a team of seismologists 1 on the Witwatersrand of 10 x 1010 ft.lbs., that by Coates of 3.8 x 10" ft.lbs., also referred to in the paper, that by Blan-chard2 for the catastrophic rockburst at Springhill, N.S., of only 7.4 X 107 ft. lbs., and finally the range covered by Cook, referred to in the paper. It is probable also that data for the heavy rockburst at Merkers3 in the WERRA potash area of Germany are available as it was recorded on seismographs from Moscow to Spain. It is the writer&apos;s impression that some standardization is present in the estimates above for 10 x 10 10, 3.8 x 1010 and 7.4 x 107 ft.lbs., respectively. The latter, for Springhill, represents a relatively low order of magnitude. It is obvious that any energy estimate must be related to the local geometry of openings at the time of the event. It is also obvious that any explanation of the causes of rockburst must be capable of providing a wide range of energy. However, we must remember that the energy release is an effect indicating magnitude. The cause lies with the mechanism initiating the primary failure, generating the seismic activity, to which much of the damage is probably due.

Jan 1, 1967