Search Documents

By Richard E. McElvain, I. Cave

The selection of centrifugal pumps for mill discharge duty should be based on the total circuit concept. The practice of operating the mill circuit based on limitation of the pump can result in losses in one day which would offset the pump cost. Operating data from 25 grinding circuits have been reviewed and comparative results on added mill capacity have established advantages far beyond the less significant maintenance costs with increased circulating load and better cyclone operation. Mill discharge pumps should be selected on the following basis: i) Best available design for wear performance ii) Size to provide best economic life iii) Liner material best suited to circuit conditions Pump efficiency is a secondary consideration because power consumed by pumps is small compared to mill power input. Energy dissipated in mill pumps is contributing to comminution of ore.

Jan 1, 1982

By F. J. Haller

The need for permanent, fireproof support indicated structural steel sets. Experience over the past six years, involving more than five miles of permanent underground openings, has proved that steel is permanent, safer and, in the long run, cheaper than either treated or untreated wood supports. Excavation is reduced, as are installation, transportation, and handling costs. A number of hazards are reduced or eliminated by the use of steel.

Jan 4, 1950

By Andrew Mayer

EARLY in 1942 National Lead Co. was requested by the War Production Board to construct and operate a plant for the Government to produce magnesium by the ferrosilicon process which had been developed by Dr. L. M. Pidgeon in the laboratories of the Canadian National Research Council. A contract with the Defense Plant Corporation was concluded in May 1942 and Magnesium Reduction Co., a wholly owned subsidiary of National Lead Co., was formed to carry out this project. The capacity of the plant was rated at 10,000,000 lb. of magnesium per year, equivalent to an average production of about 14 tons per day. THE PROCESS The process, in brief, is as follows: The raw materials are dolomite and ferrosilicon, 75 per cent grade. The dolomite is calcined, the calcine and ferrosilicon are ground and mixed and the mixture is briquetted. The briquets are charged into tubular retorts of chrome-nickel steel set horizontally in a furnace with the open ends projecting outside the front wall. The retorts are then closed and evacuated. Magnesium is liberated according to the reaction 2(MgO, CaO) + Si = 2Mg + 2CaO, SiO2 It is distilled from the charge and condensed on a removable sleeve in the throat of the retort. Sodium and potassium, if present, are also liberated, distilled and condensed on a "sodium condenser" in the end of the retort. At the expiration of the distillation period the retorts are discharged and the cycle of operations is repeated. For the rated daily capacity of ±. tons of magnesium there are required approximately 170 tons of dolomite, equivalent to about 85 tons of calcine, and 16.5 tons of ferrosilicon. The retort residue, a bulky powder which at present is waste, amounts to about 87 tons. CHOOSING THE SITE The investigation to select the location of the plant was conducted by the Research Laboratories of National Lead Co. This work included geologic and economic surveys of a number of districts, examination of dolomite samples by chemical, spectrographic and petrographic methods and large-scale tests of dolomite from several of the more promising localities. In the last-named tests 2-ton samples were put through the ferrosilicon process in the pilot plant of the Canadian National Research Council, under the guidance of Dr. Pidgeon. The conclusions drawn from the investigation, in regard to the quality of dolomite to be used in the ferrosilicon process, were: First, the dolomite should contain not less than 21 per cent MgO

Jan 1, 1944

By G. L. Hundley, R. E. Mussler, D. H. Yee, F. E. Block, R. S. Olsen

An anhydrous chlorination process for the recovery of copper from chalcopyrite was investigated. Pelletized concentrate was reacted continuously with gaseous chlorine in a vertical shaft reactor at 550° and 650°C. While the copper was withdrawn with the rest of the metals as molten chlorides from the bottom, 99-x% sulfur was distilled from the top of the reactor. The molten metal chlorides were pulverized and dropped continuously into an upward flowing stream of oxygen. Over 80% of the iron chlorides were converted to oxides in a vertical free-fall reactor at 800° and 900°C while the copper chlorides passed through unoxidized. Copper was recovered in powder form by electrowinning continuously from chloride solutions using a diaphragm cell. The product sloughed easily from a titanium cathode and showed no iron contamination. Current efficiencies and power consumptions averaged 77% and 1.24 kw-hr per lb.

Jan 1, 1974

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of June, 1913: Members. ANGERER, VICTOR, Vice-Prest. and Genl. Mgr., Wm. Wharton, Jr. & Co., Inc., 25th St. and Washington Ave., Philadelphia, Pa. BULLOCK, ALLYN, Min. Engr Hazleton, Pa. CUNNINGHAM, NOEL, Met. Engr., Hollinger Gold Mines, Ltd., Timmins, Ont., Canada. ESTABROOK, EDWARD L., Supt. of Colliery 436 Center St., Ashland, Pa. GATES, A. 0., Instructor Purdue Univ., La Fayette, Ind. LUDLUM, ALBERT C., Prest., New York Engrg. Co., 2 Rector St., New York, N. Y. MILLER, HERBERT F., Met. Engr P. 0. Box 142, Verona, Pa MORTON, ELMER T., Min. Engr Clifton, Ariz. MURFIT, RICHARD H.. Fdv. Asst Hess Steel Castings Co., Bridgeton, N. J. QUAYLE, THEODORE W., Chief Sampler, Metcalf Mines, Arizona Copper Co., Metcalf, Ariz.

Jan 7, 1913

By Shosei Serata, Bruce Gardner

A system of three new field instruments has been developed to measure, in situ, the three basic classes of geomechanical parameters: material properties, stress state, and creep deformation. The significance of this development is that it represents a successful adaptation of recent computer technology to underground rock mechanics work, opening up new possibilities in underground mining methods. The system was developed to meet the application requirements of the stress control method of mining, a method which is based on the actual geomechanical conditions of the underground, rather than upon conventional linear-elastic, idealizations of ground conditions. These instruments enable in situ measurement not only of elastic, but also post-elastic, yielding, and failure conditions of geological materials, establishing the stress control method on a truly scientific foundation. In order to evaluate the present status of this field instrumentation system, case examples of underground mine openings designed with the stress control method are reviewed and analyzed, in terms of the effectiveness of the three instruments for informing and guiding the site-specific application of stress control design.

Jan 1, 1984

By Daniel T. O’Brian

Exploration targets and results in the mining industry are commonly summarized in terms of tonnage and grade. Business appraisals require, as additional information, the expected profit or loss implied by the physical summary. The early incorporation of knowledge gained through financial analysis computations can provide a means for economically resolving many common exploration and development problems. Examples of such applications from the activities of exploration planning, reconnaissance, land acquisition and develoment planning follow. While prospecting for mineral deposits, geologists are frequently asked what they have found or hope to find. The response is usually descriptive, such as: "50 million tons of 1% copper," and the economic implications are deferred until a capital investment decision is required. At that time a financial analysis integrating the four analysis components-tonnage and average grade above cutoff grade, capital and operating costs, product value, appropriate profit or loss accounting-are completed.

Jan 10, 1969

By M. G. Schuerger, D. W. Park

An improved gage for monitoring fractures in underground openings was successfully developed using the reflection photoelastic technique. The gage may be used to detect crack initiation in mine openings or tunnels so reme¬dial action may be taken to prevent further deterioration. Fringes concentrated around the cracks were spread by using rubber backing. Crack growth as little as 76µm (0.003 in.) up to as much as a 2.54-mm (0.1-in.) width were detect¬ed in this study. Variation of gage materials will provide alternative ranges. The feasibility of the method was tested and calibration was made in a laboratory study. Field study successfully demonstrated the capability of applications in detecting mine roof crack development.

Jan 1, 1984

By Felix Wunsch

WHILE the effect of the cold-junction temperature has been known by many, its consideration has been ignored in a number of installations, resulting at tunes in a very considerable error. In fact, the magnitude of this error may amount to over 100° in some cases. While hand-operated correcting devices for portable checking pyrometers may be entirely satisfactory, it is, of course, desirable to have such apparatus en¬ Millivoltmeter Thermocouple Platinum Wire Mercury FIG. 1.-EARLY `METHOD OF AUTOMATICALLY COMPENSATING FOR COLD-JUNCTION TEMPERATURE CHANGES. tirely automatic, when applied to curve-drawing or printing pyrometers, otherwise there is no assurance that the record is correct. Numerous methods for automatically compensating for cold-junction temperature changes of thermocouples have been proposed and used in connection with millivoltmeters. One of the earliest proposed was that shown in Fig. 1. A bare resistance wire was immersed in a column of mercury located near the cold junction of the thermocouple. An increase in temperature near the cold junction resulted in a rise of the mercury column, which short-circuited more of the resistance wire causing an increase in the potential difference across the millivoltmeter, which compensated for the decreased electromotive force of the thermocouple.

Jan 9, 1919

By Chas. A. Ashburnea

THE appliances which have been proposed, and the modifications in the construction of boiler-furnaces which have been made for the prevention of smoke, and the utilization of what are ordinarily called the waste products of combustion, have been innumerable.† †There is now open in London an exhibition "of apparatus of all kinds devised to prevent smoke."

Jan 1, 1882

By J. Birkinbine

Extended discussions, by inviting attention to problems affecting the conservation of natural resources, have encouraged investigations as to their sufficiency, with the general result that the more thorough the examination, the less cause appears for anxiety as to the exhaustion or serious depletion of these resources.

Jan 1, 1915

By A. C. Dorenfeld

CHANGES in circuits are often made in milling operations. At the same time that these changes are being evaluated the ores are changing. Even from the same mine, the ore is usually variable as to amount and type of mineral content, degree of association of valuable and gangue minerals, amount and types of soluble salts, hardness, etc. The question then arises whether any small differences in results, after changes have been made in the various circuits, are really due to these changes or whether the variability of the ore can account for those differences. Statistical evaluation provides one method of answering the question that arises so often in beneficiation studies: Did changed results come about because of changed process, or did ore variation cause the change? In this case, data were available for statistical analysis from an operating period of 42 months, representing treatment of approximately 1 million tons of ore. During this period there had been two flowsheet changes: 1) regrind of the zinc circuit middlings was introduced, and 2) alcohol- pine oil frother mixture was substituted for cresylic acid-pine oil frother mixture. Findings are in Table I.

Jan 10, 1954

Although the Suggestions to Institute Authors, as revised and amplified over the years to meet changing conditions and experience, have had as their primary objective the guidance of the author who is preparing a paper for record in the TRANSACTIONS, there are in this current version many excellent suggestions for the preparation of any material for publication by the Institute In this connection it should be emphasized that in a sense, and to a degree determined by the editors, the Institute has in its journals "a place for everything," especially a place for the article of practical nature that is of immediate but not necessarily permanent interest Such articles may be referred by the Institute Technical Publications Committee to the editors or submitted directly to them , [Papers (TECHNICAL PUBLICATIONS and TECHNICAL NOTES) authorized for the TRANSACTIONS are, with the discussion, gathered together at the end of the calendar year and with a table of contents and index, bound, according to Branch classification, as volumes of the TRANSACTIONS

Jan 1, 1952

By F. G. Miller, J. M. Podgursky

Laboratory and pilot plant work on tabling of 14-mesh X 0 hydrocyclone under flow are summarized. Included are: operating principles of hydrocyclones and tables; performance of these two devices, separately as well as in combination; comparison of the combination hydrocyclone-table system with other fine-coal processing systems; and application of the hydrocyclone-table system in fine-coal circuits. The data show that the table actually compensates for the shortcomings of hydrocyclone and makes a combination table-hydrocyclone system attractive, particularly in those cases where fine pyrite is one of the major contaminants.

Jan 1, 1973

Jan 1, 1916

By Charles Fulton

EXPERIMENTAL work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such, a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc lead ores, since the residue from the distillation is held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet

Jan 9, 1919

By Dan Chun

Abstract-To facilitate the efficient handling of large volumes of information generated by logging exploration drill cores, a computer data bank system (GEOBANK) has been developed to store and retrieve the normally difficult to handle geologic information as well as the physical testing data. The data bank systematized the logging of drill core by first developing a standard list of adjectives or descriptors (with the corresponding assigned numerical codes) for the various stratigraphic categories that are also assigned numerical codes. The system uses the "floating-slot" concept and handles the data bank with one single input form.

Jan 9, 1978

By S. K. Bradford

For years past I have traveled in quest of promising mining-properties, over almost impassable mountain-trails to remote places in the mining-regions, usually many miles from an assay-o5ce. If, upon examination, the fornlation and the ore-deposit appeared favorable, a quick determination of the value of my samples was necessary, in order that I might take intelligent action with reference to the acquisition of the property. A journey with my samples to civilized regions often meant weeks of delay, and perhaps loss of opportunity. How many, under similar circumstances, have returned with their assay-results from such a journey, only to find that some audacious speculator had optioned" the property! True, a first payment could have been made and the chances taken on the results; but experience has taught that rich-looking ore is not of necessity valuable. Personally, I would not hazard a ten-dollar bill on any property without first determining by assay the value of the ore. To carry the usual complete assay-paraphernalia over such mountain-trails was impracticable by reason of the loss of time involved, the great expense of transportation (charged -

Jan 1, 1911

By A. L. Field

This general subject has been so thoroughly discussed by Dr. Herty and his associates, especially with regard to the degree of oxidation of the metal at the time that the silicon pig or spiegel is added, that I am not going to spend much time on that today. I should like to propound a question, which is based on my own observations made some years ago while with a large alloy-steel company which had two open-hearth furnace plants. It is true that one of these plants was not engaged particularly in making alloy steels, but there were certain relations between slag and metal composition which appeared to me to be entirely different in the two plants. I have an explanation for it that is more or less incomplete, but possibly Dr. Herty or Mr. Reinartz or some of the others may be able to complete it. Suppose we take our three layers; the metal on the bottom, on top of that the slag, and on top of the slag, the gas. We cannot overlook the gaseous phase. Regardless of the effect of the iron oxide in the slag on the rate of carbon elimination—and that, of course, is rather important in alloy practice since it is not desirable to have the carbon dropping too rapidly at the time the deoxidizing is had in the furnace—it will probably be admitted that it depends on the iron oxide in the metal for a given carbon oxide. I have seen cases where with approximately identical metal and slag compositions one furnace would work twice as rapidly as another in removing carbon. Of course, there is some explanation of this in what others have already said, that the question of the exact lime and silica content of the slag determines the activity and viscosity of the slag; but I am convinced, without having reviewed the actual records since I was asked to make this talk, because they were not available at the time, that the slags in these two furnaces were not materially different. Putting it another way, one furnace would have

Jan 1, 1935

By A. L. Field

This general subject has been so thoroughly discussed by Dr. Herty and his associates, especially with regard to the degree of oxidation of the metal at the time that the silicon pig or spiegel is added, that I am not going to spend much time on that today. I should like to propound a question, which is based on my own observations made some years ago while with a large alloy-steel company which had two open-hearth furnace plants. It is true that one of these plants was not engaged particularly in making alloy steels, but there were certain relations between slag and metal composition which appeared to me to be entirely different in the two plants. I have an explanation for it that is more or less incomplete, but possibly Dr. Herty or Mr. Reinartz or some of the others may be able to complete it. Suppose we take our three layers; the metal on the bottom, on top of that the slag, and on top of the slag, the gas. We cannot overlook the gaseous phase. Regardless of the effect of the iron oxide in the slag on the rate of carbon elimination—and that, of course, is rather important in alloy practice since it is not desirable to have the carbon dropping too rapidly at the time the deoxidizing is had in the furnace—it will probably be admitted that it depends on the iron oxide in the metal for a given carbon oxide. I have seen cases where with approximately identical metal and slag compositions one furnace would work twice as rapidly as another in removing carbon. Of course, there is some explanation of this in what others have already said, that the question of the exact lime and silica content of the slag determines the activity and viscosity of the slag; but I am convinced, without having reviewed the actual records since I was asked to make this talk, because they were not available at the time, that the slags in these two furnaces were not materially different. Putting it another way, one furnace would have

Jan 1, 1935