Search Documents

By Paul Merica

ONE of the most useful, and at the same time least commonly used, methods of thermal analysis for the determination of transformations in metals and alloys consists in the recording of the tune intervals required for successive increments of temperature change during heating or cooling, the temperature of the furnace containing the specimen being altered at a uniform rate. The curve obtained by plotting these time intervals as a function of the mean temperature of the specimen during the interval is called the inverse-rate curve. It is probably due to the fact that no simple and convenient method has apparently been available for the measurement of the successive time intervals that this method has not been so generally used as, for example, the differential method, for which several tykes of automatic or semi-automatic apparatus have been designed. Whenever this method has been used, the intervals have usually been measured with the use of a chronograph; its operation as practised at the Bureau of Standards' is as follows: The temperature of the specimen is measured by a thermocouple and a dial potentiometer. The operator sets the potentiometer at successive values of the electromotive force differing by equal increments, usually 0.02 millivolt, and records the exact instant on the chronograph, by pressing a contact key, at which the galvanometer coil passes through its null position. Two-second intervals are also recorded on the chronograph record, and the number of 'seconds elapsing between successive signals is afterward counted from the record and plotted as a function of the electromotive force or of the temperature. This is an admirable method and by it most minute thermal arrests may be detected, but it requires a good chronograph, which is generally difficult to obtain, and the time of one operator during the recording and, subsequently, to read the intervals from the record; the latter operation often takes from one to two hours.

Jan 7, 1919

By Roland W. Rammler

With oil consumption increasing more rapidly than known reserves in industrial countries, there has been a growing interest in the production of synthetic crude oil. The main starting materials for such production are coal, oil shale and tar sand, all of which occur in enormous quantities in North America. A process sequence suitable for all three of these starting materials incorporates a preliminary retorting step to produce oils for subsequent hydrotreating. For this retorting step, a technique known as the Lurgi-Ruhrgas process has proven highly efficient. The process has been commercially used for the flash carbonization of coal and has also been tested in pilot- plant experiments with oil shale and tar sand.

Jan 1, 1970

By W. R. Webster

Opinions still differ widely concerning the requirements, chemical and physical, which should be expressed in specifications for steel rails, in order to secure results satisfactory to both manufacturers and purchasers.

Jan 1, 1902

By B. L. Seegmiller

Horizontally stratified lithologies of certain open pit or strip mines create unique stability problems for mine operations. Such problems may result when specific lithologies, such as sandstone and shale, exist in final or long-term slopes. Slope instabilities may occur when a sandstone unit directly overlies a shale unit and ground water drains into the mine along the lithologic contact. In essence, the ground water erodes the underlying shales and undercuts the sandstone. Large sandstone blocks fail in a toppling mode and cause safety and cleanup problems. Use of rock reinforcement including chain link fencing, roof bolt mats, rock bolts, rock anchors, and shotcrete offers a possible solution to the problem.

Jan 1, 1985

By W. Joseph Schlitt, Kenneth J. Richards, John D. Prater

Kennecott Minerals Company has developed a leach-hydrolysis route for treating flue dusts from copper smelters The flue dusts are acid leached in an oxygen atmosphere to solubilize copper and fix the arsenic, antimony, and bismuth as stable compounds Copper is recovered by cementation with Iron and the barren solution is recycled Molybdenum and other values may be recovered by modification of the basic flow sheet Results of bench scale and pilot plant tests are discussed in terms of the effect of operating parameters.

Jan 1, 1981

By J. Landau, A. Dim, R. Houlihan

Recent developments in the application of solvent extraction in hydrometallurgical processing make it desirable to reassess the present state of availability of suitable equipment for these applications. The range of solvent extraction applications now includes very large scale applications with a modest demand on separation performance (the treatment of some base metals) and applications in which the decisive factor is a very high requirement on separation performance. The extraction column to be described in the present paper is of the type in which mechanical energy is provided for the two- liquid system inside the column. The active elements for this are reciprocating sieve plates designed and mounted so as to uniformly load the driving mechanism, to eliminate vibration of the plant, to have sufficient control over the degree of dispersion of the dispersed phase, and to reduce axial mixing effects, which are highly detrimental to the separation performance of production-scale plant. The operating features of the reciprocating-plate column will be illustrated mainly by experimental results obtained on a 4" diameter column in the extraction of uranyl nitrate with TBP. Some mechanical features of the operation of reciprocating-plate columns will also be discussed.

Jan 1, 1973

By H. R. Hanley

ELECTROLYTIC zinc produced from sulfate solution and, with pure lead anodes is always contaminated with a small and varying percentage of lead. The purpose of this investigation is to determine the characteristics of several lead alloys and their influence on the products of electrolysis and power consumption. The study of alloyed anodes has been a matter of interest for some years. Tainton, Taylor and Ehrlinger prepared a highly interesting paper1 on this subject a year ago, in which the effects of silver-lead and some ternary alloys of lead-silver-tin were described. The present paper describes a study of various combinations of 10 metals. The general plan of the work provides for the fabrication of the alloyed anode, its adequate conditioning by preparatory electrolytic operation, the production of cathode zinc and its analysis, the determination of the anode polarization, and other features. A list of the anodes tested, showing composition and polarization at various current densities together with the lead assay of the cathode zinc, is shown in Table 1.

Jan 1, 1930

As we understand the functions of the A. I. M. E. Petroleum Division, they are to discover and promote knowledge for the benefit of society on the mining of oil and gas. To the individual member of the Petroleum Division, there are certain advantages of social and professional contacts, but the collective purpose is that described. And the individual is benefited by membership only as the Division measures up to the purposes of its existence. Consequently, the welfare of this Division and that of its members depends upon the extent to which it keeps pace with the needs of society on matters relating to the mining of oil and gas. To some extent, A. I. M. E. activities must be determined by the changing current needs of society. The great problem ahead of the world for some time is to evolve equitable types of production control in many industries, and especially is that true of the oil industry. Production control in this industry is as much an engineering function as is production development, notwithstanding it also involves the lawyer, the economist and the politician. It must be built on and around suitable engineering planning enforced by public opinion and legislation. We believe the prerequisite to any satisfactory solution of the oil industry's ills is an educational campaign establishing a better public understanding of the needs and merits of production control, by which we mean the maximum yield at the minimum cost coordinated to society's current needs. The underlying causes of the oil industry's ills are well known and generally agreed upon. In like manner there is general agreement among students of the industry that the first step toward their correction would be general adoption of oil-field developing and operating methods that would permit most efficient use of reservoir energy; that would provide for equitable distribution of oil and gas among the several owners in the pool; and also for the extraction of these products in response to market demand. It is now found, however, that general adoption of such developing and operating methods unfortunately cannot be brought about without changes being secured in certain basic laws of oil and gas, and perhaps also in the anti-trust laws. These legal changes are difficult to secure because of the widespread fear that they would tend to place the oil industry more exclusively in the hands of the major companies, and that

Jan 1, 1932

By W. A. Boyer

Mine hoisting ropes can be loaded to capacity only when the strength of each component is exactly known. Characteristic curves provide this information. When load and rate of acceleration are specified for an individual rope, the characteristic curve assumes a predetermined shape. The factor of safety is the value derived by dividing the breaking strength of the rope by the total stress on the rope where it goes over the sheave wheel. Total stress is made up of the weight of skip and cage, weight of ore, weight of rope between sheave and rope clevise or attachment, friction load, and acceleration force. Bending stresses are neglected in this discussion, as sheaves and drum diameters are assumed to be large enough to reduce these stresses to a negligible value.

Mar 1, 1956

By P. Lindstrom

Retreat mining, using yielding steel friction props, over a 7-year period has been successful at a uranium mine operated by Hecla Mining Co. in southeast Utah. The support system allows good roof control, maximum profit, complete extraction, and good ventilation. Unusual subsidence observations were made in that some of the surface was raised rather than lowered. Longwall mining, commonly practiced in European coal mines, has a potential of broader application because of mechanization possibilities and better roof control and ventilation at greater depths. The Radon mine was one of the first American metal mines to use yielding steel props for supporting the relaxed core of the pressure arch which is induced by retreating longwall mining. Full caving was induced. After more than 7 years of stoping experience, the method has proved very satisfactory for the conditions encountered. The mine and method have been described in references listed in the bibliography. U.S. Bureau of Mines Information Circular 8004 by Wilbert Dare and Philip Lindstrom gives the most information. Stoping experience at this mine indicates that there are many advantages to be gained by using yielding supports; such as in safety, timber cost, roof control, ventilation, ore dilution, and low cost per pound of metal produced. Subsidence measurements show that the surface will rise rather than slump in some areas over the mine. This appears to be an unusual observation and is presented as a new development in subsidence studies. The Radon mine is located 35 miles southeast of Moab, Utah in the north end of the Big Indian mining district in San Juan County. Hecla Mining Co. operated the mine from early 1955 to early 1964 through an operating agreement with Federal Resources, Inc. Development consisted of a 3-compartment, 690-ft shaft, 4 main levels driven on the ore horizon and a haulage level below the ore. Evaluation of physical and economic factors showed that this flat-dipping ore occurrence could be mined by a low-cost coal mining method. The value of the deposit was high and unusual premiums were possible by clean mining. Complete extraction without loss of ore pillars, minimum ore dilution and high production per man were obtained by longwall mining. The principle of working under the relaxed core of

Jan 1, 1964

By L. C. Morganroth

Discussion of the paper of L. C. MORGANROTH, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 475 to 481. DAVID B. REGER, Morgantown, W. Va.-I notice in the third paragraph of the first page of the paper, that in mentioning the clays of the Pottsville series, the author says: "The bed of clay found in the latter formation is unique in that flint clay is practically restricted to it. (A variety of flint clay is occasionally found in these upper deposits but this is in such small amounts as to be negligible."). If the author wishes to confine himself to the fire clays of Pennsylvania, as the title seems to indicate, I have nothing to say, but if he wishes to include a discussion on fire clays of the adjoining States which the. subsequent paragraphs of his paper seem to indicate, then I wish to call attention to the fact that there are large and extensive deposits of fire clay in the Allegheny series, immediately overlying the Pottsville in the northern counties of West Virginia. These fire clays have been studied carefully, and described in several reports of the West Virginia Geological Survey, first in the report on Ohio, Brooke, and Hancock Counties, in the northern part of the State; described later ,in the report on Monongalia, Marion, and Taylor Counties, and in the report on Preston County, which followed. In these latter counties (Monongalia, Marion, Taylor, and Preston) there are some beds of fine fire clay, varying in thickness from 6 to 10 or 12 ft., with a content of only 2 or 3 per cent. of fluxing ingredients, and these are of the typical Savage Mountain appearance and also have the typical Savage Mountain fracture. They have been prospected, but not mined a great deal. Several of them have been tested in blast furnaces and furnaces for other purposes, in glass-manufacturing plants, also for firebrick, arid have been found to be very good. They are simply awaiting development, and I merely want to call attention to the fact that there are plenty of them in the Allegheny series still above the Pottsville in West Virginia. There are two or three valuable seams which I have seen in person and have had analyzed in our laboratory.

Jan 5, 1916

By C. H. Frick

Before presenting the main topic, as indicated by the title, this paper will give some of the high-spot history of the anthracite industry. Introduction The earliest recorded use of anthracite was in the year 1762, when a company of Connecticut pioneers discovered anthracite near the present city of Wilkes-Barre, Pennsylvania. In the early days of the industry, the coal was used only in large pieces, the smaller pieces being discarded to waste piles. As the output of the industry increased during the nineteenth century, uses were developed for somewhat smaller sizes down to and including pea coal. Early in the twentieth century, sizes smaller than pea, such as No. I and No. 2 buckwheat, were developed and used. Accumulations of piles from current mining operations were still increasing; that is, the smaller sizes were still being discarded. It was not until after World War I that preparation of the so-called steam sizes began commercially. This was largely No. 3 buckwheat, which is screened through a 3/16-in. round-hole screen and over a 3/32-in. or a 1/16-in. round-hole screen. Use of Smaller Sizes The earliest recorded experience in burning the small sizes of anthracite for steam production, other than in a previous small experiment, was in the year 1913, when a size known as "boiler fuel" was introduced—a mixture of rice and barley (No. 2 and No. 3 buckwheat). At that time, there was still no method known for burning the still smaller sizes. At the present time, various sizes down to and including No. 5 buckwheat are being prepared (Table I) from current mining and bank-reclaiming operations. The sizes of No. 4 and No. 5 buckwheat and smaller are generally being used for steam production in large boilers. The Pennsylvania Power and Light Co., following World War I, used 680,000 tons of anthracite per year, burned largely on stokers for production of steam, whereas for the year 1943 it used 1,940,000 tons of stoker sizes and 400,000 tons of smaller sizes for grinding and burning in pulverized form. This company has taken a very large part in the research and development of ways and means of burning these smaller sizes of anthracite, including the grinding of the very small sizes. This paper is particularly concerned with the latter feature.

Jan 1, 1949

By Y. C. Liu

THE existence of mechanical twins in bcc metals has long been known. With recent intensive interest in the mechanism of twin formation and its role in plasticity and crack initiation, a study of the general Characteristics of twin intersection appears pertinent. The scope of the present note will be limited to the crystallography of the twin intersections of (112) twins, without consideration of its mechanism, movement of atoms, crystal structure, or the strain energy involved at such an intersection. The twinning elements of (112) twins are considered to be K1 = {112}, n1 = (111) and K2 = {112}, n2 = (111) with a twin shear of 0.707. The crystallographic features of twin intersections have been worked out in detail by Cahn.1 The present work applies the general principles postulated by Cahn to the intersections of (112) twins. The basic conditions for the twin intersection are: 1) The trace of crossing (A) and the secondary (C) twins in the planes of the crossed twin (B) must be parallel. 2) The direction (n1) and magnitude (s) of shear must be identical in the crossing and secondary twins. Also the sense of shear must be the same. These two conditions have to be fulfilled in order to maintain geometrical continuity at the twin interfaces. Fig. 1 shows the perspective representation of how these two conditions are fulfilled at the intersection. This type of intersection will be named Type-I. It is the purpose of this note to point out the existence of another type of intersection, Type-II, as shown in Fig. 2. In this type of intersection, the crossing twin A remains straight and the crossed twin B has been bent. The two conditions laid down by Cahn must also be met. This leads to the following corollary conditions: 1) The interface between twins B and C must be parallel to the twin habit of crossing twin A. 2) n1c must be parallel to n1A. 3) The twin shear (s) of twin C must be exactly equal to and in the same sense as that of crossing twin A. Thus, in order for the Type-II intersection to take place, the twining elements of secondary twin C must fulfill the above three conditions with respect to crossing twin A. Let K1 of crossed twin B be (112). All indices of the matrix can therefore be converted into new in-

Jan 1, 1963

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By Ikuya Takase

INTRODUCTION Since the occurrence of the first oil crisis, coun-tries of the world, especially oil-importing countries have made sustained and vigorous efforts to lessen the dependency on oil as a source of energy supply. The adoption of "Principles of Coal Policy" by the IEA Ministerial Governing Board Meeting in May, 1979 was the first formal action taken by major energy consuming countries. At the Venice Summit in June, 1980, it was agreed that production and use of coal should be doubled over the next ten years. In fact, the world coal use in 1980 showed around a 10 percent increase over the previous year. Recently, we have seen an indication that the balance of oil supply and demand in the short term have eased. But I believe that it remains vital that we continue to encourage the development and introduction of alternative energy sources. Because, from the medium and long range viewpoint the recovery of the worldwide economy will lead us to increased oil requirements and thus we will be faced with the cyclical, structural tightening situation between the supply and demand of oil. Moreover, we are still convinced that the constraint of the supply capabilities of the Middle-East nations may be increasing in the long-term, since there still remains political uncertainties among these nations. Consequently, above all, coal is viewed as an alternative energy resource available for immediate expansion of use and is given as high a priority as nuclear power. In Japan, we regard coal as the most reliable alternative energy resource to replace oil. According to the "Alternative Energy Supply Targets" approved by the Cabinet in November, 1980, the level of coal imports is estimated to approximately double by 1990, while our domestic coal production will remain nearly at the same level. The transition from oil to coal is found in the recent import levels of coal---73 mil¬lion tons in 1980, a 23 percent increase over the 59 million tons imported in 1979. There was an upsurge in steaming coal imports, reflecting the transition in feedstocks---7.2 million tons in 1980, four times over the previous year's amount. Henceforth, from the medium to long range view, the demand for coal, especially that of steaming coal is forecast to continue to grow. The timely expansion of supply capabilities is our utmost concern and should be one of the most significant goals of our comprehensive policy. The Overseas Coal Investigative Committee, a privately organized advisory panel to the Director-General of the Natural Resources and Energy Agency of the Ministry of International Trade and Industry (MITI), investigated means to secure a stable supply of overseas coal. The panel presented its interim proposals in August, 1981, recommending the diversification of coal import sources, extensive use of low rank coal, as well as enhanced international cooperation between coal producing and importing countries. THE CONTENTS OF THE COMMITTEE'S REPORT Four Points for Major Consideration In order to ensure a stable supply of overseas coal, Japan needs adequate policy measures consistent with the characteristics of coal resources and environmental requirements, giving consideration to Japan's status and the role she is expected to play in the areas. From the above, great importance should be attached to the following four points: All the components of the "Coal Chain" (Namely, the development of mine sites, construction of railroads, port loading facilities, coal shipping vessels, port receiving facilities, including coal centers and international transport facilities etc.) should be reviewed and reformed with steps taken to assure efficiency consistent with the entire coal chain system. The complete formation of a coal chain system requires such lengthy lead times and huge amounts of investment that necessary measures should be undertaken well in advance utilizing long-range projections of future demands and various economic surveys. Policy planning should be conducted taking into account of harmonizing stability and economics of the supply structure. For ensuring the long-term stability and expansion of the coal trade, international cooperation on a bilateral and multi-national basis should be encouraged. Mutual understanding and close relationships are essential to facilitate the formation of the supply system and to promote the extensive use of coal. Direction and Problems Related to Supply Stability Expansion of Supply Capabilities. World coal imports in 1979 amounted to 229 million tons, of which Japan's share amounted to 59 million tons, or one fourth of the entire amount. The imports of European and Asian countries accounted for 83 million tons and 7 million tons respectively. According to the examination of the Investigative Committee, Japan's coal requirement is estimated to be between 140-150 million tons by 1990, nearly the same level as announced in the Provisional Long-Term Energy Supply and Demand Outlook in 1979. This fore¬cast is-to be revised in April, 1982. Japan's demand is expected to be met through fiscal 1985; however, by 1990, the supply is estimated to fall short of demand, particulary, in the field of steaming coal. For the expansion of supply capability, first, mine development should be accelerated. The proposed

Jan 1, 1982

September 28, 1915. The Nominating Committee of the American Institute of Mining Engineers has the honor to present the following nominations for officers of the Institute to be voted for at the 1915 Annual Meeting: For President: L. D. Ricketts District 0 For Vice-Presidents: Karl Eilers District 0 James MacNaughton District 4 For Directors: Thomas B. Stearns District 7 Charles F. Rand District 0 Charles W. Goodale District 5 Edwin Ludlow District 2 George D. Barron District 0 F. W. BRADLEY, Chairman.

Jan 11, 1915

By W. W. West

MACHINERY used for size reduction of materials may be divided into three classes-depending upon the manner in which the crushing force is applied. In the first class could be listed the primary crushing units, such as the jaw crusher and gyratory crusher-which crush to coarse sizes by applying pressure intermittently between converging surfaces. In the second class may be listed crushing units, such as the hammer mill, roller mill, and ball mill, which crush principally by grinding or attrition. In the third class is the impact mill which, as the name infers, crushes by impact. The second and third classes generally include machinery used as secondary units for intermediate or fine crushing and grinding. Theory of Crushing by Impact Throw a stone into the air and give it a severe blow while it is momentarily suspended, and it shatters into several pieces. The impact crusher uses this "batting" principle, but carries it one step further. As the material to be reduced enters the crushing chamber, it receives a severe free-air impact blow by hard-hitting beaters suspended from rotor discs. The shattered particles formed are then driven at high velocity against impact blocks, where a further reduction in particle size takes place. The rebounding particles from the impact blocks are again caught by the beaters, and the process repeated until the material is swept out of the open bottom of the crusher. Impact Crushing Versus Attrition Crushing Fig. 1 shows a Hammermill type of attrition crusher. This particular mill has central feed and is reversible. Because of the central feed, an impact section can be designed into it at the feed entrance for preliminary crushing, followed by the cage bar attrition area for final sizing. The material is caught and held in a crushing chamber enclosed by grate bars or perforated plate. It remains in this chamber until it is reduced to particle size small enough to pass through the openings between the bars or in the plate. In this manner the top particle size discharged from the mill is closely controlled. As the swinging hammers pass through the bed of material, the material is broken down by a scrubbing action between hammers and material, material and grate bars, and material against material. This attrition produces a rounded particle shape, accompanied by slivers and a comparatively high percentage of fines. The crusher is especially useful in industries where the material treated is not too abrasive, such as limestone, cement or coal plants. It can be readily understood that from the maintenance standpoint, it is not suitable for hard abrasive materials such as refractories and aluminum oxides. One common type of impactor is shown in Fig. 2. The bottom of this type crusher is entirely open and the passage of the material through the crushing chamber is almost instantaneous. Liberal clearances are maintained between the impact hammers and the anvil type breaker blocks. This eliminates practically all attrition. It is the elimination of attrition that makes the impactor particularly adaptable for reducing hard, abrasive materials. The impactor is also well suited for the reduction of wet or frozen materials, which clog an ordinary Hammermill. Particles broken by impact, when examined under the microscope, show a distinct tendency toward rough, cubical shape, with a minimum of fines. Another important factor in impact crushing is that crushing is accomplished along natural cleavage lines, thus freeing foreign ores or materials.

Jan 1, 1952

By Oliver B. Hopkins

The Peruvian production increased over 3 million barrels from 1933 to 1934—from approximately 13¼ million barrels to over 16¼ million barrels—bringing the cumulative production of the country up to 171 million barrels. Most of this production, as well as most of the increase in 1934, came from La Brea-Parinas Estate, the property of the International Petroleum Co., Limited. In 1932 Peru stood eleventh among the oil-producing countries of the world, but in 1933 her production exceeded that of Trinidad, Argentine and Colombia, which placed her in eighth position. In 1934 Peru's production was exceeded by that of Colombia by about one million barrels, and by that of the Argentine by about 1½ million barrels, thus placing her in tenth position. After several years of relative inactivity in drilling and exploration there was a noticeable increase during 1934 in both of these lines of activity. Oil Fields La Brea-Parinas Estate.—Production on the La Brea-Parinas Estate. reached a significant total of 85,080 bbl. as early as 1891. It increased to over one million barrels in 1912, and to over 10 million barrels in 1929, and in 1934 it reached an all-time high of over 14 million barrels. The total production from 1890 to 1934 was 133,784,609 barrels. Practically all the drilling on the property has been done with cable tools, but during 1934 three strings of rotary tools were introduced. One was a heavy outfit for drilling a deep test and the other two were lighter outfits for deepening wells in the newer section of the field, where the gas pressure was too high to permit safe drilling with standard tools. During 1934 a total of 28,127 ft. was drilled, 66 wells were deepened, and 6 new wells were completed. At the end of the year 2844 wells had been drilled on the Estate, of which 1814 were still productive. The remaining 1030 wells represent abandoned producers or dry holes. The total area that has been productive up to the present time is estimated at 13,369 acres. An interesting article on the various phases of operations of the International Petroleum Co. was written by Arthur Iddings and published in The Oil and Gas Journal (Dec. 27, 1934).

Jan 1, 1935

By R. A. Ronzio, P. B. Queneau, C. A. Born

The molybdenite flotation operation of Climax Molybdenum Co., Division of AMAX Inc., near Leadville, Colo., generates a rougher tailing containing 0.03% W03 and 0.005% SnO2. This tailing is subjected to a series of mineral beneficiation steps for production of wolframite and cassiterite concentrates. However, these byproducts are contaminated by small quantities of UsOa. This paper describes application of sulfuric acid-sodium chlorate leaching for substantial elimination of the radioactive impurities, particularly the mineral brannerite. The leached residue is amenable to magnetic separation of wolframite from cassiterite.

Jan 1, 1976