Search Documents

By Bernard Greifer, Walter Rose

The purpose of this note is to call attention to a source of difficulty which can be responsible for inaccurate estimates of wetting liquid pressure gradients in mixture flow experiments of the Hassler1 type. It has been our experience occasionally to observe what were indicated to be negative pressure gradients, and these were regarded as anomalous in the sense that physically they seemed to contradict the requirement that the flux be in the direction of the potential field. At first it was thought that our scheme of assembling barriers and core sample led to such asymmetry in the distribution of isobars that the manometric leads at each end of the core were responding to internal pressures (within the core sample) which could be either positive or negative with respect to each other, and which in fact might tend to reflect on different effective core lengths in an unpredictable fashion as the wetting liquid saturation was changed. However, no compelling evidence of this possibility has been established. In addition, we were cognizant of the requirements to be satisfied in selecting manometric instrumentation to minimize the delay in response of the manometer to the differential pressures being measured, and were thus assured that our observations of anomalous pressure gradients could not be explained by faulty instrumentation. What we suggest is that if a leak sink occurs in the fluid lines connecting the core to either side of the differential manometer, errors exceeding 100 per cent may result in the estimation of wetting liquid pressure gradient, even though the leak is of such small magnitude that its existence would tend to be obscured by evaporation effects. This is because in a system with leaks at the specified places, the manometer rec- ords at steady state the pressure drop across the manometer barrier elements in addition to the pressure drop across the core sample. This possibility will be illustrated below analytically and by numerical example for the special case where the leak occurs on the high presure side of the core, since we are especially desirous to explain the significance of our observations of the so-called negative pressure gradients. It will be indicated, however, that leak sinks on the low pressure side of the core can account for observations of anomalously high values of pressure gradient, and that multiple leaks on both sides of the core can provide for some compensation so that the errors in pressure estimation are reduced. However, the major point to be emphasized is the fact that the impractical-ity of detecting the small leak sinks which give rise to the difficulties makes it a complicated task for the experimenter in a particular case to know with certainty that his estimation of pressure gradient lies within the limits of error which can be tolerated. Fig. 1 shows the electrical analog of the flow system we have employed in our studies. The inflow and outflow barriers. Rbl and Rb2, the manometer barriers, Rm1, and Rm2, and the core sample, Rc— for a particular fluid saturation and distribution— are all designated as resistance elements; the flowmeter is designated by an ammeter, A; the pressure source is designated by E; and the manometric device is designated by the voltmeter, V. Included in the circuit are the variable resistances, Rx and Ry, which may be regarded as the leak sinks, and which, in general, can vary in magnitude from zero (i.e., a large hole or shunt in the system) to infinity (i.e., no

Jan 1, 1950

By Ernest Stütz

(New York Meeting, October, 1918.) THE problem of increasing blast: furnace efficiency through diminution of flue-dust production while operating with burdens consisting largely of fine ores has of recent years attracted the attention of metallurgists, whether directly or indirectly interested in the economies of iron smelting, and the various methods evolved from theory or practice have been submitted to wide discussion. After the very thorough and, at that time, exhaustive view of the whole subject, which was afforded to the industry by the meeting of this Institute in February, 1912, the subject was again taken up at the meeting of the Verein deutscher Eisenhüttenleute at Diisseldorf in December, 1912. While American and German conditions are not entirely identical, it may be of interest to give here the words of the gentleman summing up the discussion at the Diisseldorf meeting: ' The chief advantage offered by the use of briquettes lies in the fact that disturbances in the furnace, caused mostly by the presence of fine ores in the burden, are avoided, and that blast pressure can be considerably reduced. The resulting economies cannot be overrated, as, with lower blast consumption per ton of product, the installation will be able to take care of increased production. In consequence of lower pressure and speed of blast, heat is more efficiently utilized, flue gas temperature is lowered, and coke particles are less liable to be carried along with the flue dust, of which considerably less is produced. Finally, by increased regularity of operation and higher . temperature in the lower parts of the furnace, the quality of the product is improved. The question of briquetting iron ores has grown to be one of the most important in the iron industry, and, it is not any more a question of what is the cost of briquetting ton of ore, but what, in using ore briquettes, is the cost of production of a ton of iron.'

Jan 7, 1913

By P. R. Swann, R. M. Fisher, W. R. Duff

Observations by transmission electron microscoPy of the microstructures in quenched Fe-A1 alloys provide the basis for revision of the Fe-A1 phase diagram. The diagram is characterized by first-order transitions between the disordered ferromagnetic a! solid solution and the two ordered phases FeAl and Fe3Al. However, second-order transitions showing corre-luted fluctuations in the degree of order near the critical temperature occur between the paramagnetic a! and FeAl and the FeAl and FeAl phases. ELUCIDATION of the true nature of the Fe-A1 equilibrium diagram has proven to be an extremely challenging problem as evidenced by the fact that six quite different versions of the iron-rich portions have been published since 1958.&apos;-6 The most recent diagram shown in Fig. 1 was proposed by Rimlinger6 based on X-ray diffraction analysis and dilatometry. He shows the single-phase fields of the ordered phases of the types FeAl(L20) and Fe3A1(D03) and the disordered bcc Fe-A1 solid solution, a, separated from one another in every case by large two-phase regions. Thus, he implies that in Fe-A1 alloys ordering always occurs via a classical phase transition. In contrast to this view, theoretical studies3&apos;" have concluded that the transitions a — FeAl and FeAl — Fe3A1 should be second- or higher-order in character. A further revision of the Fe-A1 diagram of state is presented in Fig. 2 based on our previous8,9 and current observations by transmission electron microscopy of the microstructures found in quenched specimens. The average quenching rate was 50,000°C per sec and although this was sufficiently rapid to prevent Fe3A1-type ordering below -550°C it was not sufficient to suppress ordering of the type FeAl in the temperature range -650" to 800°C. However, ordering during the quench is easily recognized since the FeAl phase formed during holding at temperature rapidly develops large antiphase domains whereas FeAl formed during quenching has a very fine domain size, -50Å diam. Each symbol in Fig. 2 indicates the result of a micro-structural examination of specimens heat-treated (-1 hr) until equilibrium was established. The results will be discussed in the order of the points, A - Dl marked on both diagrams with reference to the phase fields, critical temperature, and "transition" ranges, respectively. The dark-field micrograph corresponding to point A is shown in Fig. 3 and was obtained using a 111 reflection of the Fe3A1 structure which reveals both a&apos;/4<111> and a&apos;/2<100> antiphase domain boundaries.10 The structure observed in this specimen is typical of single-phase Fe3A1 and shows no evidence for FeAl or any other additional phase. The dark-field micrograph shown in Fig. 4 corresponds to point B on the two diagrams. It was taken with a 100 FeAl reflection which reveals a/2(111) domains and exhibits the typical structure of single-

Jan 1, 1970

By M. B. Kasen

eralized strain equation appear quite different they are really identical. This identity can be shown in a simple mathematical rearrangement. Referring to Eq. [I], the substitution of ln(1 +?E) for ? (where ?E is the engineering strain) yields: a =s8- (s8?so)e?1/?c) ln(1 +s8??E) [4] or s =s8?(s8?so)(l +?E)-1 [5] Replacing (1 + cE) with its equivalent, (l/lo): s=s8?(s8?so)l/€c [6] Adding and subtracting the quantity (s8 - so) yields: s=s8?(s8?so)+ (s8-so) l-(^)l/£c [7] = s0+(s8?so)ri-(^0)1/^l [8] Letting n = 1/?c it follows that: This equation will be seen to be identical to the generalized strain expression in Eq. [3], the coefficients a and b being equal to so and (s8?so)/?c or n(s8?so), respectively. Confirmation of the relationship noted above was provided by fitting experimental stress-strain data5 for 304 stainless steel (total strain from 0.072 to 1.15) at room temperature at a true total strain rate of 4 x 10-3 sec-1 to Eqs. [I] and [3]. In this study nonlinear regression analyses were used to evaluate the equation constants. The results of this evaluation are presented in Table I. When these constants are used in Eqs. [I] and [3] the curves obtained are coincident. It will also be noted that the value of n is equal to YE,, the value of a is equal to so, and the value of b is equal to (s8 - so)/Ec. These equalities are illustrated in Table I where the Voce constants in parentheses were calculated from a, b, and n values. Excellent agreement is seen to exist. It is concluded, therefore, that the Voce equation is, indeed, identical to the linear expression involving generalized strain. In applying the generalized strain concept to stress-strain data, it has been noted3 that data within what was termed the transition region (first few points in the plastic flow region) must be excluded from the analysis in order to obtain the linearity in Eq. [3]. A similar exclusion applies in the use of the Voce equation since an expression which would describe the strain-hardening region would usually be found to be not too effective in the elastic-plastic fillet2 which connects the elastic line to the strain-hardening region. These considerations further substantiate that Eqs. [I] and [3] do indeed describe identical behavior. Note added in proof. Since this manuscript was submitted for publication, correspondence with Professor S. R. Davies, University of Edinburgh, (of Ref. 3) indicated that his associates have also confirmed the identity between the Voce equation and the generalized strain concept. It is sometimes desirable to obtain a small grain size in super-purity metals. Unfortunately, the absence of impurities, the low recrystallization temperatures, and the low activation energies for boundary motion result in rapid growth of relatively few grains when conventional recrystallization practices are used. For example, Arajs et al.1 were unable to obtain a mean grain diameter less than about 0.4 mm in iron containing 38 at. ppm of impurity. The <1 at. ppm purity range in many modern superpurity metals results in yet larger limiting grain sizes. It is the purpose of this communication to describe a technique by which mean grain diameters as small as 30 µ have been produced in aluminum having an impurity content < 0.5 at. ppm. The technique should be applicable to superpurity metals other than aluminum and has potential applications to grain refinement of commercial alloys. The necessary and sufficient requirements for production of a small grain size are as follows: a) a large number of potential nucleating sites must be created randomly within the cold worked material, b) sufficient thermal energy must be provided at a rate that will simultaneously activate a large fraction of the potential nuclei, and c) the grain growth must be stopped shortly after grain impingement.&apos; A high density of potential grain nuclei may be cre-

Jan 1, 1970

By J. F. Martin, J. E. Friedline, L. M. Melnick, G. E. Pellissier

A method has been developed for determining gases in steel in which the gases are extracted by vacuum fusion and analyzed by mass spectrometry. This method is especially applicable for determining small amounts of oxygen and nitrogen. The lower limit of detection for both oxygen and nitrogen is 0.0001 pct with an average deviation of about 0.0001 pct for oxygen and 0.00008 pct for nitrogen. Hydrogen analyses by this method are in good agreement with analyses by vacuum tin-fusion. A complete analysis of all gases extracted from a steel sample can be accomplished in 40 min. It has long been known that certain of the gaseous elements exert particular effects on the physical and mechanical properties of steel. With the recent advent of new experimental steelmaking practices it is now possible to obtain steels with extremely low contents of such elements as oxygen and nitrogen. Present methods for determining these two gases are of insufficient sensitivity as applied to steels made by these newer practices, and therefore a new technique was considered necessary. A review of the literature showed that the conventional vacuum-fusion method1 was the procedure most suitable for modification to obtain a sensitive method for determining the gaseous elements present in steel simultaneously. However, for trace amounts of gases it is impractical to increase the sample size because of the physical limitations of the apparatus and the increased degassing time which would be necessary. Also, when only one of the desired gases is present in trace amounts, quantitative separation by conventional vacuum fusion is almost impossible. Since small analytical mass spectrometers are now commercially available, it was decided to use this instrument in conjunction with conventional vacuum fusion for both qualitative examination and quantitative determinations of the gaseous elements in steel. This technique has already been used with success for the analysis of copper and lanthanum.2"4 APPARATUS A vacuum-fusion unit was first designed and built, Fig. 1. This unit was designed especially for the determination of small amounts of nitrogen and/or oxygen in steel since an acceptable method (vacuum tin-fusion)5 was already in use for the determination of hydrogen in steel. The vacuum system was con- structed of Pyrex glass throughout. Mercury check valves were used in place of stopcocks in the high-vacuum section of the system. Ferromagnetic samples are normally introduced into the vacuum system through a mercury lift. In case of a break in the lift, the mercury is prevented from entering the furnace by a self-locking, mercury safety check valve, Fig. 2. This check valve, developed at our laboratory, is a modified T/S ball-and-socket joint placed in the sample inlet system between the mercury and the furnace. A sudden entry of mercury or air pushes this valve into the closed position, completely blocking the top of the mercury lift. The check valve is held in the closed position by the vacuum of the apparatus. A separate entrance tube also was placed in the system, so that samples which would amalgamate with mercury, or which are nonmagnetic, could be introduced into the furnace. A slightly modified Guldner-Beach furnace is used in this system.8 The optical flat was connected to the system by a ground-glass joint to facilitate cleaning, a quartz delivery tube was substituted for Pyrex, and the crucible was used uncovered. Fusion takes place in a high-purity graphite crucible insulated by — 200-mesh high-purity graphite powder. The crucible set (crucible and funnel) is suspended in a quartz crucible. The furnace envelope and the sample inlet system are exhausted by 2 single-stage, mercury-diffusion pumps in series. The first of these is a high-speed pump, which will work only with a very low backing pressure. This pump is used to exhaust the gases from the furnace as rapidly as possible. The second mercury-diffusion pump is used as a backing pump for the first; the capacity of this pump is much lower. However, it will work efficiently against a back pressure of 3 mm of mercury. To assure positive pumping, a modified Naughton and Uhlig condenser7 is used. With the use of proper valving the second pump is also used as a circulation pump in the catalyst system.

Jan 1, 1959

By Fritz Wald, Martin Weinstein, Herbert E. Bates

ONE of the methods for preparing a fiber-reinforced composite is that of directional solidification of a eutectic melt. Its major drawback lies in the fact that the matrix in this case is a pure constituent (or a terminal solid solution of fixed concentration) and the ratio of fiber to matrix volume is fixed. Only very few, if any, pure metal matrices possess technically useful properties, and the necessity for alloying is the inevitable consequence of this fact. Nevertheless, structures similar to binary eutectic ones can be obtained in higher-order systems by pseudoeutectic reactions of a type where crystallites and a solid-solution matrix are simultaneously precipitated from a liquid.1"3 Trials to solidify such alloys directionally—the matrix consisting of a solid solution of chromium, nickel, and silicon and the reinforcing phase being Cr3C2— will be reported elsewhere.4 This note describes constitutional studies carried out primarily to determine -the position of the pseudoeutectic and further to insure that no undesirable reactions between the reinforcing phase and components of the matrix occur in the solid state at elevated temperatures. In the investigation it was specifically desired to reinforce a matrix which is as close as possible to the 80/20 Nichrome composition with Cr3C2 to insure good oxidation resistance and improve the strength at high temperatures. No konstitutional information on the quaternary C-Cr-Ni-Si svstem in the range of interest was found in the literature. Nevertheless, the two most important ternaries c-cr-Ni5 and have been completely investigated. On C-Cr-Si some investigations have been conducted,7"9 and C-Ni-Si was studied with a few alloys in the course of the present investination 9 Eight alloys were prepared to investigate the changes in the constitution of the ternary C-Cr3Ce-yNi eutectic5 with silicon contents up to 10 wt pct. Five alloys were made with varying chromium and carbon contents around compositions containing -60 to 70 wt pct Ni and 5 to 6 wt pct Si. The latter alloys were designed to locate the y(Ni-Cr-Si-C)-Cr3C2 pseudoeutectic reaction and to determine the maximum chromium content in solid solution compatible with a two-phase equilibrium between y and Cr3C2 only. The alloys were prepared from electrolyte nickel, semiconductor-grade silicon, high-purity chromium (99.999 pct pellets), and semiconductor-grade graphite. They were melted inductively in high-purity alumina crucibles under flowing argon. Twenty-gram charges were prepared and investigated by optical microscopy (including hot-stage investigations), X-ray powder methods, and electronmicroprobe analysis. The alloys were studied in the as-cast condition and also after a homogenization annealing treatment of 48 days at 900°C in evacuated quartz ampoules. The structures of all alloys based on the ternary eutectic plus silicon in the as-cast state consisted generally of an inhomogeneous solid solution and at least two other phases. Annealing of the alloys showed that the solid solution was homogenized but that an incomplete solid-state reaction had taken place in all alloys with silicon contents over 5 wt pct. This reaction is clearly visible in Fig. 1 around the large Cr3C2 crystals (gray areas). Below this concentration, the alloys consisted of a homogeneous matrix and precipitates of Cr3C2 plus graphite, Fig. 2. The Cr3C2 was entirely unreacted here. From these observations and subsequent X-ray and microprobe investigations, it was deduced that the

Jan 1, 1969

By P. R. Sahm, T. V. Pruss, D. A. Gandolfo

Cb 3 Sn powders were hot-pressed to estahlish densi-fication conditions and assess the possible use of such compacts in multiphase structures with ceramic or magnetic inclusions. Superconducting transition temperatures, Tc, were measured as a function of powder particle size, pressing temperature, and second-phase admixtures. The highest transition temperatures were found in coarse powder (5 to 500 u) compacts and were only weakly depended on pressing temperatures up to 1200°C. Fine powders (below 5 p), however, both single-phase CbsSn and Cb3 Sn-composites, showed a stronger dependence on hot-pressing temperatures. While Al2 O3 phase admixtures did not affect T, much more, a Pronounced T, degradation was observed upon the addition of ferrimagnetic Fe2 Mno. 5 Zno.5 O4 powders. Likewise, critical current densities, Jc, at 4.2° K were lowered appreciably in the ferrite doped samples, whereas the neutral A1203 inclusiow gave slightly improved Jc values. MULTIPHASE structures in electronically active materials have recently gained in interest as pointed out by Galasso in a review article.&apos; In superconductors the most widely reported group are eutectic alloys which have been mostly investigated with respect to the proximity effect.2"4 In addition, "artificial eu-tectics", for example in the form of mercury-vycor glass sponge5 or fine niobium wires imbedded in a copper matrix,= have been prepared to attain higher critical fields and critical current densities. The idea was to enhance flux pinning phenomena by second-phase inclusions or ho1es. 7 Flux pinning should also be possible by the introduction of insulator inclusions into a superconducting matrix. Ceramic-metal combinations are most easily produced by hot pressing (= pressure sintering), as it permits an almost unlimited selection of material combinations. Cb 3 Sn has been prepared by vapor phase growths or in the form of thin films. Large compacts must be sintered,1° however, and normally present difficulties. At temperatures below 1350°C insufficient densities are obtained and at higher temperatures the loss of tin due to dissociation upsets the stoichiometry. Hot pressing is a natural approach to circumvent the problems, since one can obtain satisfactory densities despite low sintering temperatures. This work was mostly concerned with establishing conditions to hot press Cb3 Sn and Cb3 Sn multiphase structures (= composites), because no data are presently available, and to evaluate these with respect to their transition temperatures. However, a few measurements on critical current densities were also carried out, in particular to assess the value of ferrimagnetic inclusions. I) EXPERIMENTAL PROCEDURE The experimental procedure involved the preparation of feed material and powders, hot pressing, and evaluation of the resulting ingots. As no attempts were made to synthesize Cb3Sn from the elements during hot pressing, feed material had to be produced. For this purpose, a stoichiometric Cb-Sn powder mixture was compacted into a 3-cm-diam ingot (80,000 psi) and then inserted into a quartz tube and evacuated. Rf heating was employed. Above the tin melting point (230°C) liquid tin was forced out of the ingot, but was pulled back by capillary action after approximately 0.5 hr of continuous pumping at 700°C. Thus, it appears that evacuation at this temperature caused desorption of impurity gas creating wetting surfaces which, later on, favored alloying at relatively low temperatures. After a presintering period of 17 hr at 800°C, the quartz tube was tipped off and sealed into another such larger-diameter tube which, in turn, was connected to a pump system. This configuration permitted a temperature treatment at 1400°C, carried out for 65 hr, without collapsing of the glass walls or unfavorable chemical interaction of Cb3Sn with the quartz. The resulting material was

Jan 1, 1969

By B. Trenary, D. D. McNaughton, C. D. Baer

High capacity off-highway haulage trucks equipped with electric wheel drives have been available for commercial applications since 1963 and, although still interesting to study, cannot be considered as a "new" type of equipment any longer. However, the electric wheel drive components which played a key role in the development of these trucks has indirectly led to another new trucking development-the gas turbine engine for off -highway vehicles. Although most of the production models of the electric-wheel haulage trucks are equipped with 700 hp engines (the largest production engine commonly available), the electric drive components of the motorized wheel were designed to transmit more than 700 hp. To utilize this added potential, 1000-hp class diesel engines are in the process of being developed, but progress has been much slower than expected. The delay has caused some engineering thoughts to concentrate on the adaptation of the 1000-hp gas turbine engines, originally designed for aircraft applications, for use in haulage trucks. The question in most minds centered around the ability of such an engine to withstand the tough usage expected of it in an open pit.

Jan 5, 1967

By J. R. Low, M. Gensamer, W. T. Lankford

THE problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War II, it became apparent that mass production methods of forming would be required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet metals under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By W. T. Lankford, Low J. R., Gensamer M.

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By Low J. R., Gensamer M., W. T. Lankford

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By H. N. Mills

The glass industry is a major user of many industrial minerals in the manufacture of its product. It is the intent of this chapter to: (1) acquaint the reader with the glass industry by including a few production statistics, and (2) cover the various aspects of the major raw materials used to make glass. The matter of glass compositions, properties, and batches is considered beyond the scope of this chapter which deals only with raw materials. For more details on the particular minerals and rocks used in glassmaking, the reader is referred to chapters in the commodity section of this book. Glass Industry Statistics Glass manufacture in the United States can be divided into three major product classifications as follows: 1) Glass containers 2) Pressed and blown glass 3) Flat glass Glass containers include bottles and jars for the packaging of food and beverages, as well as drugs, chemicals, and cosmetics. Pressed and blown glass includes table, kitchen, art and novelty ware, lighting and electronic glassware, and fiber glass. Flat glass covers sheet or window glass, plate, laminated, and safety glass. The US Department of Commerce statistics, as recorded in the 1977 Census of Manufacturers, compares the dollar value of glass shipments for each product category. These statistics are shown in Table 1 (Anon., 1980) and are self-explanatory. A comparison of the tonnage output in each product classification is difficult, as production data is reported in "gross" for glass containers, "pounds" for fiber glass, "pieces" for glassware, [ ] and "square feet" for flat glass. In the case of glass containers, an average "pounds per gross" factor can be applied to the total production figures reported in thousands of gross in Bureau of Census industrial reports. Table 2 presents the calculated annual production tonnage for glass containers for the years 1974-1979. Except for 1979, there was a yearly increase in production. The tonnage figures of Table 2 are further influenced by decreasing weight per gross which has occurred in the glass container industry since 1975. This reflects the gradual shift to lighter weight containers for beverages. Other segments of the glass industry have experienced growth, but the figures in tons are not published information. Fiber glass growth has been influenced by the heavy demand for insulation as part of energy conservation efforts on a national basis. The production of flat glass by the float process has continued to grow with several new plants entering production. All portions of the glass industry experienced the effects of the general economic decline of 1979-1980, but the outlook for the future is bright. Batch Materials For Glass Use Materials and Function Soda-lime-silica glass represents the largest proportion of glass manufactured for commercial use. It is produced by the fluxing and

Jan 1, 1983

By H. W. Gillett

WE hear much in these days about "tailor-made" steels. Farseeing executives have sensed the demand for metals of improved and special properties, with those properties deliberately built into the steel in order to fit it for a particular use or group of uses. They have set their metal-lurgists at work to produce what the customer needs, even though the tonnage required may not, at least at first, be great. As the metal-lurgists bring out such metals, the products are advertised and the customer becomes increasingly conscious that he no longer has to take "ready-made" steel as the only thing available, whether it fits his needs or not, but that there are plenty of steelmakers ready to serve his specific needs with a tailor-made steel. Of course this is nothing new in the realm of rather highly alloyed steels to be heat-treated. The automotive industry demanded and got such steels long ago. Indeed, one could not design a modern car using only non-heat-treated carbon steel, since an engine of present horsepower would be so heavy that the gasoline required merely to lug the engine itself around would be absurd. Many different alloy steels and many different heat-treatments are required to produce the fine gradations of properties and the strength per unit weight that are needed in each particular part. Aircraft designers, of course, count a high strength-weight ratio in the materials used as Article I in their constitution, and they too, and in outstanding degree, require tailor-made alloys. Aircraft and automobiles may be considered as the tail coats and Tuxes of the metallurgical tailors. Nowadays there is also a demand for business suits, in the form of high-strength alloys to reduce dead load and so increase payload, all through the transportation industry. We hear most about weight-saving design and materials in respect to the railroads, with the spectacular new high-speed passenger trains and the prosaic freight car. The latter sounds especially sweet to steel-mill ears, because it means tonnage. While most of us think of these developments, and of the engineering acceptance of high-strength materials as "new," the fundamentals are of almost hoary antiquity. It is the widespread availability of a variety of materials and their general acceptance that are new.

Jan 1, 1936

By R. W. Shoenberger, J. A. Grina, R. J. VanPelt

The many alternatives open to coke plant operators for improving overall coke quality and strength are discussed in this paper. Programs undertaken by US Steel research and coal operations during the previous ten years to improve coke strength are described. New techniques in use, or being considered for future use, are also discussed.

Jan 1, 1982

By EVERETTE DE GOLYER

USE of geophysical methods in the search for new pools and as an aid in the development of known pools and prospects reached a new all-time peak for the oil industry in 1933. The outlook for 1934 is for work to continue at an even greater rate. The area of greatest activity, as in previous years, was in the Gulf coastal plain of Texas and Louisiana, particularly through a belt of territory some 20 to 30 miles wide parallel to the coast line and some 80 miles inland from it-the so-called "Jackson play" or "Conroe trend." This area was surveyed in an attempt to find additional pools of a type similar to Conroe, a pool not discovered directly as a result of geophysical surveys but one which was indicated by refraction surveys before it was drilled and one which was accurately outlined as to structure by reflection surveys shortly after the completion of the first few wells. Surveys were made over this belt, extending from Texas, across Louisiana and into Mississippi and Alabama, chiefly by the reflection method and torsion balance, and to some extent by pendulum and magnetic methods.

Jan 1, 1934

By A. E. Dwight, A. F. Berndt

Binary and ternary alloys of uranium with transition metals were prepared with U2X stoichiometry. The compounds U2Tc, U2Rh, U2Os, and U2lr were formed by peritectic or peritectoid transformations, and were shown to be isostructural with U2Ru. The lattice constants are presented. Miscibility relationships obtained from the study of ternary alloys are graphically summarized in terms of an area-of-stability plot. The compound U2Re is not isostructural with either U2Ru or U2Mo. A series of compounds with stoichiometry U2X has been prepared in which X is technetium, rhodium, rhenium, osmium, or iridium. The only other U2X compounds, for which X is related to the above transition metals by proximity in the periodic table, are U2Mo and U2Ru. The structure of U2Mo is the tetragonal C11b type (MoSi2 type)1 and U2Ru is monoclinic, with a new structure type.&apos; This investigation was undertaken to determine if any of the above compounds are isostructural with either U2Ru or U2Mo and to find the range of occurrence of these phases. EXPERIMENTAL Alloys were prepared from stoichiometric amounts of electrolytic uranium (99.99 pet pure) and transition metals of 99.5 pet purity (98+ pet pure Tc), by arc melting on a water-cooled copper hearth under an Ar-He atmosphere. Weight losses were negligible. The buttons were homogenized at temperatures between 700o and 800°C (900°C for U2Tc) in evacuated capsules and air-cooled. The X-ray powder specimens were annealed briefly at the temperature of homogenization. Except in the case of the technetium alloy, metallographic examination was used to determine the number of phases present. The radiation hazard involved in handling technetium precluded the use of metallography to examine U2Tc. The temperature and mode of formation of the U2X phases were determined by heating the metallographic specimens to successively higher temperatures, until examination indicated the presence of chilled liquid or a peritectoid transformation. RESULTS The U2X compounds investigated were found to be formed under the following conditions: UzTc unknown U2Ru peritectic 897o ± 3°C U2Rh peritectoid 755o ± 5°C U2Re peritectoid3 below 750°C Uas peritectic4 920°C U2Ir peritectoid 775o ± 5oC Debye-Scherrer patterns for the above U2X phases were made with CuKa radiation (nickel filter). The similarities in the positions and intensities of the strongest lines in the front-reflection region strongly suggested that U2Tc, U2Ru, U2Rh, U2Os, and U21r are isostructural with only minor differences in the unit-cell dimensions. The known lattice constants and intensities of the Debye-Scherrer rings for U2RU2 were used as a guide in order to index the low-angle X-ray reflections of the U2TC, U2Rh, U2Os, and U2Ir powder patterns. Approximate lattice constants for these compounds were thus obtained and were used along with the intensities observed for U2Ru to index the strongest lines in the back-reflection regions. A sin2 2? correction term was included and the lattice constants were refined and standard deviations estimated by least squares. Comparison of observed and calculated values of Q(= 4 sin2?/?2) used in these calculations are given in Table I. In each case when the positions of lines could not be resolved on the films they were not measured. The final lattice constants, with their standard deviations, are given in Table 11, along with the unit-cell volume and X-ray density. The values of the atomic volume5 of the transition ele-

Jan 1, 1965

By David B. Reger

The exhaustion of oil and gas in the United States is proceeding at a rapid pace. This is especially true in fields where the light oils that furnish the most fuel for internal-combustion engines arc found, leading to a late estimate by Arnold that the petroleum resources are 36 per cent. exhausted.l The further remark by Dr. David T. Day at the New York meeting of the Institute, in February, 1916, that the operators of the country are now scarcely able to supply the ever-increasing demand for gasoline, leads the writer to believe that a determined effort will soon be made to secure deeper producing horizons in those regions that now furnish high-grade oil, and in which pump stations and pipe lines offer convenient means for the economical handling of new production. A study of Arnold&apos;s table shows further that the States that produce paraffin oil exclusively are 45 per cent. exhausted, this figure being much higher than the average of paraffin and asphalt States altogether. The most extensive of all the paraffin-oil-producing areas is the Appalachian Field, extending with the Appalachian Geo-Syncline from western New York southwestward through western Pennsylvania, western West Virginia, Ohio, Kentucky, and Tennessee, where oil of high gravity is always secured. Of these States, Pennsylvania and West Virginia rank highest in the quality of their product. In West Virginia, the oil sands dip to a lower level than in any other locality in the Appalachian Geo-Syneline, the Pittsburgh Coal of the Pennsylvanian being only 50 ft. above sea level along the Nineveh Syneline at Wileyville, Wetzel County.² The very significant fact that the sands of the Mississippian and Upper Devonian Measures furnished the richest oil pools of the State along this

Jan 1, 1917

By Ole Singstad

THE legislatures of New York and New Jersey, determined in 1919 that a vehicular tunnel should be built under the Hudson River. On July 1, 1919, an engineering staff was organized with the late Clifford M. Holland as chief engineer, and this staff was given a number of problems to solve, such as location, size, type of tunnel, method of construction, method of ventilation and cost. After a period of preliminary investigations and studies it was decided to build the tunnel at Canal St., New York, connecting 12th St., Jersey City. This is the center of the heaviest traffic across the Hudson River. It was also decided to build two tunnels-one for west-bound traffic and one for east-bound traffic-the tunnels to be of cast iron, built up of segments and bolted together, each tunnel to have a roadway 20 ft. wide and a clear heat room of 13 ft., 6 in. This is to provide for two lines of vehicles in each direction. The tunnels have an exterior diameter of 29 ft., 6 in. The interior lining is of concrete, the sidewalls tiled with a vitreous white tile and the roadways paved with granite block. The entrances and exits at both ends are separated by two blocks so as to reduce traffic congestion. BASIS OF VENTILATION It was recognized very early that one of the most important problems confronting the engineers was a proper ventilation system. It was estimated that each tunnel as planned would have a traffic capacity of 1900 vehicles per hr. The tunnels are 8500 ft. long between portals, and it was considered that the ventilation should be based on all of these vehicles being operated by gasoline engines. That presented a problem in ventilation unlike any other either in magnitude or character.

Jan 8, 1926

By T. Wasson

Midland and Isabella counties have been the centers of activities for the year 1932. The major part of the 6,967,000 bbl. produced during the year was obtained from the old Mt. Pleasant field and the Eastern Extension field. The total production to the end of 1932 for Michigan, from all fields since discovery, is 20,679,600 bbl. Production in the Eastern Extension field was obtained from Dundee limestone of Devonian age, at a depth of about 3600 ft. As a result of the year&apos;s activity in this area, the limits of the Eastern Extension have been defined. No new fields have been discovered. A number of prospective areas have been drilled and condemned by dry holes. Probably the most outstanding development of the year was the discovery of oil on the Yost farm, in sec. 35 of Greendale Township, Midland County, by the Pure Oil Co., in the early part of December. Production is from the Dundee limestone similar to that in the Eastern Extension but is 4 miles south of that area. The first well has averaged about 500 bbl. per day since completion. It is near the center of a solid block held by the Pure Oil Co., so that rapid development due to competitive drilling is not expected. During the early part of the year the Midland-Isabella area was under proration, but on May 17 proration restrictions were discontinued and remained so until the end of the year. While the Eastern Extension saw the principal activity, some work was done in other fields of Midland and Isabella counties, but very little new production was added. The Vernon field on the north showed a slight increase in production over 1931. The Leaton field decreased. The well in Porter Township, Midland County, is still kept in the production ranks but very little drilling was done in that area. The old Saginaw field, Saginaw County, still remains the only spot in the state where commercial production is obtained from the Berea sand. It showed a slight decline over 1931 with no new producers for the year. The Muskegon field on the west side of the state showed a considerable decline over 1931, but owing to the rejuvenation of some wells by the use of acid this drop was not as great as might have been expected. Only two new producers were drilled in that area.

Jan 1, 1933

By David Reger

Introduction THE exhaustion of oil and gas in the United States is proceeding at a rapid pace. This is especially true in fields where the light oils that furnish the most fuel for internal-combustion engines are found, leading to a late estimate by Arnold that the petroleum resources are 36 per cent. exhausted.1 The further remark by Dr. David T. Day at the New York meeting of the Institute, in February, 1916, that the operators of the country are now scarcely able to supply the ever-increasing demand for gasoline, leads the writer to believe that a determined effort will soon be made to secure deeper producing horizons in those regions that now furnish high-grade oil, and in which pump stations and pipe lines offer convenient means for the economical handling of new production. A study of Arnold&apos;s table shows further that the States that produce paraffin oil exclusively are 45 per cent. exhausted, this figure being much higher than the average of paraffin and asphalt States altogether. The most extensive of all the paraffin-oil-producing areas is the Appalachian Field, extending with the Appalachian Geo-Syncline from western New York southwestward through western Pennsylvania, western West Virginia, Ohio, Kentucky, and Tennessee, where oil of high gravity is always secured. Of these States, Pennsylvania and West Virginia rank highest in. the quality of their product. In West Virginia, the oil sands dip to a lower level than in any other locality in the Appalachian Geo-Syncline, the Pittsburgh Coal of the Pennsylvanian being only 50 ft. above sea level along the Nineveh Syncline at Wileyville, Wetzel County.2 The very significant fact that the sands of the Mississippian and Upper Devonian Measures furnished the richest oil pools of the State along this

Jan 9, 1916