Search Documents

By John W. Cloud

In 1877 the Pennsylvania Railroad Company removed an old bridge from its line at Duncannon, Pa., built intermediate piers and erected shorter spans of the Pratt truss type, which had previously been in use on another portion of the road. The design of this truss would not admit of diagonals larger than 19 inches diameter, and in order to stiffen the bridge somewhat steel rods were introduced for the main diagonals in the first and second panels, 19 inches and 18/8 inches diameter respectively. These rods were threaded without upsetting, and by the ordinary formulae the strains were of the same intensity upon both, viz., 16,000 pounds per square inch with the maximum loading. The other main diagonals in the truss are 19 inches diameter, and of iron. It was specified for the steel rods: Elastic limit,.......46,000 Ibs. Tensile strength,. .. ,. .. 80,000 lbs. Elongation,,.,.,. 20 per cent. The steel was procured without difficulty, and it allowed a factor of safety of 23/4 at elastic limit, while a similar factor of 2½ had for a long time been successfully used for iron. In the course of three years, from time to time, six of these steel rods broke, three of them being 18 inches in diameter, and three 19 inches in diameter. The broken rods were tested, and three of them analyzed at Altoona to ascertain the cause of failure, and what modifications should be made in the steel for such service. Examination showed that all the rods were broken in detail close under the nut. The threads were well cut and properly rounded at the root. testing the rods micrometer screws, reading to .0001" with c bell to signal the contact, were attached to the test pieces, and by this means the modulus of elasticity and elastic limit accurately obtained.

Jan 1, 1881

EDUCATION for the mineral industry was at first a single comprehensive curriculum, but it was early recognized that the main basis of mining is physics, while that of metallurgy is chemistry. The first school to offer curricula leading to degrees in mineral industry education in the United States (1853) had separate ones in mining and metallurgy. The Columbia School of Mines (the fist really successful one) had only a single curriculum when it opened in 1864, but within a few years had so reorganized its work that it offered curricula in mining, metallurgy, geology, chemistry, and civil engineering. Interest in the metallurgy or geology curricula was slight at fist, and for the next 30 years the great majority of Columbia students took the mining curriculum, probably partly because it contained nearly as much geology as the geology curriculum, practically all the metallurgy, and most of the chemistry, and partly because of the degree awarded for it. Other schools kept their mining curricula equally broad, and as late as 1900-1910 men were graduating as mining engineers who were practically as well prepared to make geology or metallurgy their life work as they were for mining. Gradually, however, the subject matter of mining geology and metallurgy became so enriched through research and development that separate curricula in them became worth while; their progressive development is the subject of another chapter. Mining curricula also began to be somewhat diversified, and schools in areas where coal mining was of outstanding importance began to offer options in coal mining, the earlier curricula having been chiefly aimed at metal mining. The petroleum industry began its meteoric rise about the same time as mineral instruction in this country, but little more of applied science attended its birth than had attended such ancient practical arts as copper and iron

Jan 1, 1941

By G. Knight

In most mines the major contribution to the dust exposure of miners arises from rock hand- ling. Scooptrams are frequently used and produce 8 to 1300 mg of respirable dust for each ton of ore loaded. It is shown that sprays at drawpoints are not fully effective in wetting the rock and suggestions for improved wetting techniques are given. Techniques for improved dust control by ventilation and local filtration are described. The problem of dust from ore- passes and dumps on tramming levels are outlined.

Jan 1, 1981

Jan 1, 1934

By James Chapman

THE observations here presented are those, not of an expert accountant, but of one who, while he has seen considerable service in the accounting departments of large companies, has spent more time in engineering and operating. This paper is intended to cover, in a measure, mine accounting for small mines, as distinguished from the elaborate systems, requiring many persons ;n the accounting department. I shall attempt to outline a system embracing the essentials of accounting, and simple enough in form to permit one or two persons to carry it on from month to month, in sufficient detail to be able to tell quickly the grade of ore, the prices received for metals, costs per ton for mining and milling, costs per foot for development, upward or downward tendencies in costs, ore settled or in transit, cash on hand, stocks of supplies on hand, efficiency of' labor, etc. As in all accounting, there are two main divisions: that of revenue received for what is sold, and that of disbursements made for what is bought, so in mine accounting we have to consider chiefly the income derived from sales of ore or concentrates, and the expenses incurred in producing the said ore or concentrates in a marketable condition.

Jan 3, 1916

By Sam Tour

SOME years ago, the writer described heat checks or thermal cracks that occur in die-casting dies.1 The life of dies was considered in relation to the casting temperature, the material used for the die, and the heat to be absorbed by the die per unit volume of casting made. The mech-anism of the action that results in thermal failure of dies was described. In the present paper the writer proposes to describe some additional observations in regard to heat checking, make one or two suggestions as to the method or methods for further attack of the problem, and give the results obtained on some work carried out along these lines.

Jan 1, 1934

By C. S. Allen

WITH increased coal production and mechanization of coal mines many transportation problems arise. The main objective is to bring the coal to the tipple or dump it as quickly as possible. Larger and faster haulage locomotives or two locomotives connected in tandem have been adopted to solve the problem. Motor equipment, gears and control systems of locomotives to be placed on these hauls are carefully studied to meet these requirements, by an analysis of motor characteristic curves with the corresponding tractive effort curves, in order to determine the correct load for maximum efficiency and to determine the approximate schedule. Control equipment is usually considered to be the controller and resistance. Sometimes accelerating curves are calculated in order to obtain smooth starting in the least possible time without slipping the wheels. Train control is very important, but why limit this to acceleration? Deceleration or retardation of the locomotive is a part of the train control and should be given as much consideration as the control for acceleration. TYPES OF BRAKING Common braking systems for mine locomotives utilize screw-type mechanical brakes, dynamic braking and the air brake. For gathering and haulage locomotives, the screw-type mechanical brake is regarded as standard. A brake of this kind cannot be applied without much effort and lapse of time. Motormen, like other people, follow the path of least resistance, and therefore have their brakes ready for instant application-which means that the shoes are virtually dragging. Even then, a motorman bucks and plugs the motors to gain time and avoid as much physical effort as possible. "Bucking of motors" consists in turning the reverse cylinder of the controller to parallel position corresponding to the opposite direction of travel while the locomotive is in motion, without applying power from an external source. When this occurs, both motors tend to act as series generators, because the armatures are revolving and there is residual magnetism in the field circuit. Owing to slight differences in motor manufacture, one of these will generate a slightly higher potential and will overcome the generated voltage of the second and tend to drive it as a motor in the reverse direction. This action retards the locomotive but is very severe on the segments of the reverse cylinder and on the motor commutators. "Plugging motors" is the application of power to the motors corresponding to the opposite direction of travel. In order to "plug" the motors it is necessary first to "buck" them (which reverses the connections to the motors) and then to apply

Jan 1, 1941

By D. G. F. Hedley, D. F. Coates, K. Barron

INTRODUCTION Preceding papers presented in this symposium have considered the influence of various parameters, such as geologic structure, groundwater, etc., on the stability of rock slopes and have given some analyses and guide lines for slope design. To carry out such analyses it is necessary to put numbers to these parameters; where possible, this is best done on the basis of in- situ observation and measurement. Since none of the design analyses can be considered exact and since conditions vary during excavation, it is also desirable to monitor the behaviour of the slopes as the excavation proceeds. In this manner a feedback of information on the actual excavation conditions can allow a continuous reassessment of the design parameters to be made and can give early warning of incipient failures. The purpose of instrumenting rock slopes is thus to provide information which fits into one of two categories: (a) To give basic data to assist on-site assessment and design of the rock excavation. (b) To provide data for the control and assessment of safety during excavation. The purpose of this paper is to review briefly some of the instruments and measuring techniques available for gathering this data and to indicate where such data may prove useful. This is not a comprehensive review of all available instrumentation but, rather, is a survey of some of the instruments and techniques with which the authors have had some experience and which have proven useful. STRUCTURAL ASSESSMENT Whilst most structural assessment of a site is done on the basis of geologic mapping and core examination, there exists some instrumentation which can, in particular circumstances, assist in this assessment. Seismic instruments can be used to determine the geometry of formations and to give an indication of the relative competency of rocks. These instruments operate using seismic reflection or refraction techniques and, although mainly confined to shallow sub-surface exploration, can be useful in distinguishing between soil/ bedrock contacts and, in some cases, the extent of weathered surface rock.

Jan 1, 1971

By W. A. Bruce

THIS paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to sell-spacing problems are shown.

Jan 1, 1942

By E. M. Porbansky

DURING the investigation of the electrical transport properties of copper, it became necessary to prepare large single crystals of the highest obtainable purity. In an effort to meet these demands, single crystals of copper have been grown by the conventional pulling technique—as has been used for the growth of germanium and silicon crystals.' Low-temperature resistance measurements made on these crystals show that, as far as their electrical properties are concerned, they are generally of significantly higher purity than the original high-purity material. The use of these pure single crystals with very high resistance ratios has made possible the acquisition of detailed information regarding the electron energy band structure of copper2-' and has stimulated widespread effort on Fermi surface studies of a number of other pure metals. It is the purpose of this note to describe our method of preparing very pure copper crystals by the Czochralski technique. Precautions were taken to prevent contamination of the melt from the crystal growing apparatus. A new fused silica growing chamber was used to prevent possible contamination from previous groqths of other materials such as germanium, silicon, and so forth. A new high-purity graphite crucible was used to contain the melt. This crucible was baked out in a hydrogen atmosphere at -1200°C for an hour, prior to its use in crystal growth. Commercial tank helium, containing uncontrolled traces of oxygen, was used as the protective atmosphere. A trace of oxygen in the atmosphere appears to be necessary for obtaining high-purity copper single crystals. A 3/8-in-diam polycrystalline copper rod of the same purity as the melt was used as a seed. The copper rod was allowed to come in contact with the melt while rotating at 57 rpm. When an equilibrium was observed between the melt and the seed (that is, the seed neither grew nor melted), the seed was pulled away from the melt at a rate of 0.5 mils per sec. As the seed was raised, the melt temperature was slowly increased, so that the grown material diminished in diameter with increasing length. When this portion of the grown crystal was -1 in. long and the diameter reduced to less than 1/8 in., the melt was slowly cooled and the crystal was allowed to increase to - 1-1/4 in. diam as it was grown. By reducing the diameter of the crystal in this manner, the number of crystals at the liquid-solid interface was decreased until only one crystal remained. Fig. 1 shows a typical pulled copper single crystal. The purity of the starting material and the crystals was determined by the resistance ratio method: where the ratio is taken as R273ok/R4.2ok. The starting material, obtained from American Smelting and Refining Co., was the purest copper available. Most of the pulled copper crystals had much higher resistance ratios than the starting material. The highest ratio obtained to data is 8000. Table I is an example of the data obtained from some of the copper crystals. Note that Crystal No. 126 had a lower resistance ratio than its starting material and this might be due to carbon in the melt. The melt of this crystal was heated 250" to 300°C above the melting point of copper. At this temperature it was observed that copper dissolved appreciable amounts of carbon. The possible presence of carbon at the interface between the liquid and the crystal will result in reducing conditions and negate the slight oxidizing condition required for high purity as discussed below. The possible explanations of the improvement in the copper purity compared to the starting material are: improvement in crystal perfection, segregation, and oxidation of impurities. Of these, the latter seems to be most probable. A study of the etch pits in the pulled crystals showed them to have between 107 and 108 pits per sq cm. The etch procedure used was developed by Love11 and Wernick.10 The resistivity of the purest copper crystal grown was 2 x 10-10 ohm-cm at 4.2oK; from the work of H. G. vanBuren,11 the resistivity due to the dislocations would be approximately 10-l3 ohm-cm, which indicates that. the dislocations in the copper crystals would contribute relatively little to the resistivity of the crystals at this purity level. Segregation does not seem likely as the reason for purification of the material, since the resistivity of the first-to-freeze and the last-to-freeze portions are approximately the same, as was observed on Crystal No. 124. On most of the crystals that were examined, the entire melt was grown into a single crystal. If the

Jan 1, 1964

By John R. Green

ROTARY kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary according to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. MEASUREMENTS OF KILN TEMPERATURE The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration.. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records or automatic control are desired, while optical pyrometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. I shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected from puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly o° to over 200°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without. effect of the flame temperature. There should be some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors Influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and com¬ments on the possibility of measurement and control. Of greater number and of varied influ¬ence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1941

By G. C. Gester

With the exception of exploration geological work that is being prosecuted in various parts of the mainland of Arabia, the only new developments in Arabia during 1934 were on Bahrein Island, which is in the southwestern portion of the Persian Gulf, approximately 25 miles from the mainland of Arabia. Here the Standard Oil Co. of California, through its wholly owned subsidiary, The Bahrein Petroleum Co., Limited, has continued to carry on a systematic drilling campaign and has constructed camps, pipe line and marine loading facilities. During 1934 eight wells have been completed at depths ranging from 2058 to 2253 ft. These wells have shown average initial productions ranging from 1500 to 5000 bbl., with one, No. 15, estimated as being capable of flowing as much as 11,000 bbl. per day. The oil is asphaltic in character and has a gravity range of from 32' to 34' A.P.I. The locating of all new wells has followed a plan of orderly development, with the ultimate object of obtaining efficiency of operation and maximum production. The wells are taking a penetration of 200 to 250 ft. of the lower or so-called Main productive zone. The upper oil zone, which is cased off, includes 300 to 400 ft. of alternating limestones, clays and shales and carries a heavier oil under lower pressures. The Main zone is similar lithologically to the upper zone. Micro-fauna collected from cores have shown that the oil occurs in formations of lower Eocene and Cretaceous age. Development to date has not progressed sufficiently so that either the maximum thickness of the oil-bearing horizons or the limits of the field can be determined. Something over 10,000 acres has been proven to date. Among other developments leading toward the marketing of oil from Bahrein during 1934 was the construction of a marine loading terminal. This included the laying of over 3 miles of 12-in. submarine pipe line from the small island of Sitra out into the harbor, terminating in 50 ft. of water; also the laying of more than 10 miles of gathering lines from the producing area to the terminal. Three crude oil working tanks with floating roofs were erected on Sitra Island, having a capacity of 250,000 bbl. A pumping plant was provided having a capacity of 5700 bbl. of oil per hour. This is housed in a dustproof building, as rather severe

Jan 1, 1935

By C. S. Giggins, F. S. Pettit

The oxidation properties of Ni-Cr alloys with fine grains, coarse grains, and deformed surface layers have been studied at temperatures of 900" and 1100°C in 0.1 atm of oxygen. The oxidation rates of alloys containing between 10 and 30 wt pct Cr have been found to be dependent upon the grain size of the alloy. Finegrained alloys had smaller oxidation rates than coarsegvained alloys because of the selective oxidation of chromium at alloy grain boundaries. In this compositional range alloys with deformed surface layers behaved similar to fine-grained alloys due to recrys-tallization of the deformed surface layer. In the preceding paper1 it was found that during the oxidation of Ni-Cr alloys, the volume fraction of precipitated Cr2O3 could be greater at alloy grain boundaries than at other areas of the alloy surface. In the case of alloys with chromium concentrations equal to or greater than 30 pct,* the volume fraction of Cr2O3 *AIL compositions are given as weight percent unless specified otherwise. precipitated at grain boundaries and within grains on the alloy surface both exceeded the critical amount required for lateral growth of the Cr2O3 particles and the surfaces of these alloys were completely covered with a continuous, external layer of Cr203 during oxidation. However, in the case of alloys with chromium concentrations between approximately 5 to 30 pct, the volume fraction of precipitated Cr2O3 exceeded the critical value required for external scale formation only at grain boundaries.but not within the interior of the grains. Consequently, the surfaces of these alloys had external scales of Cr3O3 over the grain boundaries but internal Cr2O3 subscales with external scales of NiO away from the grain boundaries. Under these latter conditions, it was found that chromium could diffuse laterally in the alloy from those areas covered with an external layer of Cr2O3, i.e., grain boundaries, to areas where the Cr2O3 was present as a subscale. This diffusion of chromium resulted in an increase in the volume fraction of Cr2O3 precipitated in the sub-scale zone and continuous layers of Cr2O3 could be formed at the subscale front in these regions. For the alloys used in the previous studies,' continuous layers of Cr2O3 were formed on Ni-20Cr alloys in the subscale regions after approximately 30 hr of oxidation at 900°C. For shorter periods of oxidation, the Cr2O3 layer was semicontinuous with the continuous portion at the subscale front emanating from points where the Cr2O3 had been formed as an external scale over alloy grain boundaries. Some lateral growth of a Cr2O3 layer in the subscale region was observed on Ni-15Cr and even Ni-10Cr alloys but this layer was never continuous after 30 hr of oxidation. These results indicate that the selective oxidation of chromium in Ni-Cr alloys with chromium contents between 5 to 30 pct may be dependent upon the grain size of the alloy. Fine-grained specimens in this compositional range should have a larger fraction of the surface covered with external Cr2O3 than coarsegrained specimens and the subscale areas required to be sealed via lateral diffusion of chromium should be smaller. It is therefore to be expected that a continuous layer of Cr2O3 can be formed on alloys in this compositional range after short periods of oxidation providing the alloy grain-size is sufficiently small. bo studieS2,3 have established that the oxidation behavior of alloys can be significantly influenced by pretreatments which produce mechanically deformed surfaces. It has been found that deformed surfaces usually promote the selective oxidation of elements in alloys and it is believed that these effects are due to rapid diffusion of elements in the deformed layer. In view of the previous results,' which showed that alloy grain boundaries may play an important role in the selective oxidation of chromium in Ni-Cr alloys, deformed surfaces may promote the selective oxidation of elements in alloys as a result of the numerous grain boundaries formed on the alloy surfaces via recrys-tallization during heating to the oxidation temperature. The purpose of the present studies was to determine the effect of alloy grain size and surface deformation on the selective oxidation of chromium in Ni-Cr alloys at temperatures of 900" and 1100°C in 0.1 atm of oxygen. EXPERIMENTAL The average grain diameter of the alloys used in the previous studies1 was not less than 0.04 mm and alloys with compositions between 5 and 30 pct chromium had average grain diameters between 0.04 and 0.14 mm. Since the oxidation kinetics were already available for these relatively coarse-grained alloys, it was desirable to use these same alloys in the present studies. The surfaces of the alloys listed in Table I of the previous paper were deformed by using a Model F S.S. White Industrial Airbrasive Unit, which delivered a controlled mixture of 25 µ Al2O3 particles in a stream of dry air at high velocity against the surface of a specimen. The amount of surface deformation produced by this treatment was not determined but a re-crystallized layer about 15 µ thick was formed upon annealing deformed specimens. The grain size at the surface of the specimens was reduced to an average grain diameter of 0.01 mm by annealing the deformed specimens, i.e., grit-blasted,

Jan 1, 1970

By Fred A. Anderson, George B. Wallace, Edward J. Slebir

Auburn Dam will be a thin, double-curvature concrete arch dam about 685 ft high. With a crest length of about 4000 ft, it will be the world's longest single-arch dam. The site is located on the North Fork of the American River about 40 miles northeast of Sacramento, Calif. Construction is scheduled to get under way in 1970. In planning for the design and construction of Auburn Dam (see artist's conception), the foundation material, with its various discontinuities, is being investigated and the structural characteristics of the rock mass evaluated. The investigation and testing programs will aid in defining the pertinent geologic features and their individual and cumulative influence on the foundation. The work includes geologic surface mapping, surface trenching, core drilling, geophysics, tunneling, excavating shafts and raises, performing in-situ tests, and conducting laboratory tests on core and block samples. Competent amphibolite is the predominant material in the foundation, but significant bodies of chloritic, talcose, and metasedimentary rocks, a strongly developed jointing pattern, faults, and shear zones also affect the deformability of the rock mass. A comprehensive rock mechanics program, closely coordinated with geologic investigations as well as the engineering studies, therefore is required The rock mechanics work is a combination of many analytical studies and experimental investigations. The experimental work includes laboratory tests on core samples from holes drilled for geological studies of the entire foundation and in-situ tests performed in selected areas. The laboratory testing program evaluates the general properties of all important rock types and aids in correlating many of the key structural features encountered within the foundation. To derive maximum benefit from the field tests, they are conducted in materials which represent a

Jan 1, 1970

By Robert M. Doerr

A method, based on radial distribution analysis, was developed for determining the effect of size to which a given ore is broken on the potential recovery in beneficiations targeted to selected concentrate grades. A measuring microscope and computer analysis are used to obtain the radial distribution of the valuable component in polished sections of ore.

Jan 1, 1975

By James R. Swaisgood, Ronald E. Versaw

Hundreds of shafts have been sunk in the United States in the past. Most of these have been successful however, in some instances thousands of dollars have been lost due to work stoppage while emergency measures were taken to control unexpected water flows. In cases where it was not possible to control the water, the shafts were completely lost. Many thousands of dollars have also been wasted in overconservative support design for the successful shafts. These "hell for stout" designs were necessary because of the importance of the shaft in the operation of the mine. If there was trouble in the shaft, all underground operations would come to a halt. Over-design was also necessary because no reliable preconstruction investigation methods or rational support design methods were available.

Jan 6, 1974

By George Smith

IN discussing present-day business and industrial troubles we easily drop into the habit of clinical diagnosis. Talk of this kind, with its emphasis on suspicious symptoms and abnormal tendencies, makes us all morbid. As an English essayist has put it, we may thus induce a melancholy, temper that simply in-vites the ministrations of social and political quacks. It is far better-because nearer the truth-for us to recognize that our condition is in no sense diseased, that our body politic, social and economic, is suffering merely from growing pains; that America is not de-cadent-indeed, that any lapses from staid normality are traceable to the, excesses of youth. Our chief .trouble, then, is only that our industrial state is still young; it may be that we have been growing too fast. The growth in the industrial development of our country from pioneer days to the present time has been marvelous. Too many of us, however, take all this as a matter of course-we credit this record of American progress to our American genius alone. Too often we overlook the fundamental relationship between resources and progress-that man is aided and even guided by Nature. The fact is, social advance, indus-trial progress, national prosperity all have their ma-terial basis in natural resources. In furnishing the needed mineral raw materials to the great manufac-turing industries of the United States there has been no halt, but rather a general acceleration. No other phase of American activity can show-equal advance. As the decades have passed, the winning of mineral wealth has progressed from the role of a stimulus for western exploration to that of the foundation for nation-wide business. In 1890 the Sherman law was passed; since then the population of the United States has about doubled. Since then, too, thevalue of the annual product of the mines of this country has increased better than eight-fold-from 650 millions to 51/ billions of dollars. Since then the four largest branches of the mineral industry, which supply the iron and copper, the bituminous coal and petroleum-the bone and sinew and the energy of all other American industries-have increased their annual output nearly ten-fold as to value and six-fold as to quantity. Such a growth in the volume of mineral output must be taken as a true measure of the ex-ceptional service rendered by the mines of the United States. Not only is this a much larger country than it was 38 years ago, but its growing mineral industry has met demands that have been out of all proportion to the growth of the population.

Jan 8, 1928

Beyond the industrial suburbs of Melbourne to the southeast are brown coal deposits just under the fertile soil of the Latrobe Valley. These deposits rank as one of the wonders of the world. The manner in which this resource is put to use is one of the great engineering accomplishments of our time and also a prime example of Australian elan. The brown coal, with over 60% water content, occurs in beds from 200 to 400 ft thick, under 50 ft of cover. Fifty thousand tons of coal per day move in a nearly continuous stream from mining face to boilers. The power plants supply two thirds of the State of Victoria's requirements, about 800 megawatts. Surge capacity between mine and power plant is sufficient for 12 hr steaming time! Victorian brown coals have been known since the middle of the 19th century. However, it took a strike of bituminous coal miners in 1915 to bring brown coal permanently into the picture as a fuel for power generation. In Australia, power generation is a State function. The great development of brown coals has been under the State Electricity Commission of Victoria.

Jan 10, 1964

By authority of the Secretary of War, and in response to frequent requests, the following suggested list of reading is issued by the War Department for the information of civilian engineers desiring to inform themselves on military subjects: These references have been selected, first, with a view to giving to engineers unfamiliar with the art of war a general survey of that sub-

Jan 1, 1916

CONTENTS PAGE ANDERSON, ROBERT J., and ENOS, GEORGE M.-Corrosion of Brass as Affected by Grain Size. Discussed by Henry S. Rawdon, Robert J. Anderson, Francis B. Coyle, William B. Price, and W. R. Webster 1 RAWDON, HENRYS., and MUTCHLER, WILLARD H.-Effect of Severe Cold Working on Scratch and Brinell Hardness. Discussed by W. H. Bassett, John Livermore Christie, John R. Freeman, Jr., W. R. Webster, William B. Price, Norman B. Pilling, D. J. McAdam, Jr., F. G. Smith, Zay Jeffries, F. E. Carter 3 WILLIAMS, ROBERT S., and HOMERBERG, VICTOR 0.-Relation of Heat Treatment to the Microstructure of 60-40 Brass. Discussed by 0. W. Ellis 14 Corrosion of Brass as Affected by Grain Size Discussion of the paper of ROBERT J. ANDERSON and GEORGE M. ENOS, presented at the New York Meeting, February, 1924, and issued as Paper No. 1282, with MINING AND METALLURGY, December, 1923. HENRY S. RAWDON,* Washington, D. C. (written discussion).-So numerous and so varied are the factors that affect the corrosion of metals that particular care is necessary in corrosion tests to eliminate so far as possible all extraneous factors. It appears to the writer that the question may well be asked as to whether all the necessary precautions have been observed in this investigation. It may be that the points to be mentioned were considered by the authors and found to be insignificant; however, there is nothing in the report to show this.

Jan 5, 1924