Search Documents

PRESIDENT BENJAMIN B. THAYER,1 NEW YORK, N. Y. PAST PRESIDENTS JAMES F. KEMP,1 NEW YORK, N. Y. CHARLES F. RAND,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS,1 NEW YORK, N. Y. TREASURER GEORGE C. STONE,1 NEW YORK, N. Y.. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON, NEW YORK, N. Y.

Jan 10, 1914

PRESIDENT BENJAMIN B. THAYER,1 NEW YORK, N. Y. PAST PRESIDENTS JAMES F. KEMP,1 NEW YORK, N. Y. CHARLES F. RAND,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS,1 NEW YORK, N. Y. TREASURER GEORGE C: STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 1, 1915

By Huey-Lin Luo, T. R. Anantharaman, William Klement

Two new metastable phases have been obtained in Au-Ge alloys by rapid cooling from the melt. One is of the hep structure with near-ideal axial ratio and may be considered a Hume-Rothery phase. The other has a complex tetragonal structure (a = 11.627Å and c = 22.191Å for the Au60Ge40 alloy) and may be looked upon as a superlattice made up of forty-four fee unit cells. Alloys with the tetragonal phase are charactevized by marked preferred orientation. The metastable constitution of the Au-Ge alloys is discussed with reference to the rate of cooling from the melt. THE Au-Ge equilibrium diagram features a rather deep eutectic near 27 at. pet Ge with a maximum solid solubility of 3.2 at. pet Ge in gold and is similar to the Ag-Ge, Ag-Si, and Au-Si diagrams.' The present study of the effects of rapid cooling from the melt on the structure of Au-Ge alloys constitutes an extension of similar investigations2-8 in this laboratory on alloys of noble metals with germanium and silicon. Nonequilibrium hep structures have so far been obtained by quenching Ag-Ge2, 3 and Ag-Si4, 5 alloys from the melt; an Au-Si alloy of approximately eutectic composition has been found6 to solidify in a noncrystalline state. EXPERIMENTAL PROCEDURES Twenty-nine alloys prepared from gold of 99.9+ pet and germaium of 99.999 + pet purity were investigated. The method of alloy preparation, the technique of rapid quenching from the melt, and the X-ray diffraction procedures were similar to those described previously.3, 4 Essentially, small sections (-20 mg) of thin alloy rods (-1 mm diam) were rapidly heated up to 1200°C in a graphite crucible under argon and the liquid alloy ejected by a helium blast onto a polished copper strip held on the inner periphery of a rotating wheel. The resulting thin foils were examined with or without the copper substrate in a G.E. X-ray Diffractometer or in a 114.6-cm-diam Debye-Scherrer camera. RESULTS Table I gives the constitution of liquid-quenched Au-Ge alloys, as estimated from intensities of X-ray reflections from the corresponding phases, viz., a (fee solid solution), ß (hep phase), ? (tetragonal phase), and diamond-cubic (dc) germanium. Despite unavoidable variations in the quenching rates, the proportions of the phases in different alloys were generally reproducible and stable at room temperature. There was no evidence of quenching strain, since the a doublets were well-resolved in high-angle Debye-Scherrer reflections in all cases except where stacking faults in the a fee and ß hep structures contributed to X-ray line broadening. The ß and ? metastable phases showed signs of decomposition to the equilibrium a phase and germanium only after a few hours annealing above 100°C. A few alloys around the eutectic composi-

Jan 1, 1965

State of Indiana, Department of Conservation, Division of Geology, Indianapolis, Ind. W. N Logan, State Geologist A list of the publications will be sent upon request. A series of yearly reports have been issued, with a few early exceptions, since 1869, up to and including the 41st (1916) Five of these are issued free, 18 are out of print, and the rest may be obtained at a quoted price. Beginning in 1917, the administrative reports of the State Geologist have been published in the Indiana Year Book. In 1919, the Department of Geology and Natural Resources became the Division of Geology in the Department of Conservation and separates of later reports in the Year Book are available, as follows. 3rd Report (1921), Gold in Indiana, 4th (1922), The New Albany shale, peat deposits of Indiana; 5th (1923), Petroleum conserva¬tion, 6th (1924), Conservation of natural gas; 7th (1925), Coal losses of Indiana, 10th (1928), Geological conditions in the Siosi oil field, 11th (1929), The mineral fuel resources of Indiana, 12th (1930), Oil and gas developments in 1930. (Titles of lesser interest are omitted ) The following Special Reports have been printed as publications of the Department of Conservation: Special Report 6, Kaolin of Indiana (1919), free; 21, Handbook of Indiana geology (1922), $5 to nonresidents and $3 to residents, 42, Geologic conditions in the oil fields of southwestern Indiana (1924), 75 cents to non-residents and 50 cents to residents; 55, Geology of the deep wells of Indiana (1926), $1; 75, Geology of the Silurian rocks of northern Indiana (1928), $1, cloth bound, 8125, 78, Indiana oolitic limestone map of Monroe-Owens counties (1928), $1, 79, Indiana oohtic limestone map of Lawrence County (1928), $1; 90, The geologic history of the vertebrates of Indiana (1929), $1, cloth bound, $125, 91, The ceramic materials of Indiana (1929), free, 98, The Borden (Knobstone) rocks of southern Indiana (1931), $1 25, cloth bound, $150, 101, Insoluble residue studies of Mississippian limestones in Indiana (1931), 25 cents

Jan 1, 1933

By G. T. Brookman, P. B. Katz, D. K. Martin, J. A. Ripp

With the increasing emphasis on using American fossil fuel resources, more facilities are evaluating coal conversion. In addition, those facilities now using coal are considering better coal storage procedures to minimize negative environmental impacts. For example, rainfall and snowmelt on a coal pile produce a drainage stream high in acidity, suspended and dissolved solids, iron, sulfate, and trace metals. Usually, the characteristics of the runoff stream do not allow for direct discharge to streams and lakes. Detention in a holding pond and pH adjustment are traditional methods of treating coal pile runoff before discharge. Historically, this treatment methodology has been performed inefficiently without a good data base to assess how much runoff treatment is needed to meet effluent guidelines. A model was developed to simulate runoff volume and pollutant loadings under different rainfall conditions. This model will be used to size and design treatment works for coal pile drainage. The Ohio State University (OSU) version of the Stanford watershed model was selected as the base model. The OSU model simulates overland runoff in a rural area. It includes factors such as soil moisture, depression storage, infiltration, and flow to a ground water reservoir. TRC also used the OSU co-model for acid production in coal refuse piles as the basis for qualitative modeling work. A number of modifications were made to the OSU models to make them applicable to coal storage piles. The physical/chemical reactions included in the models are described in more detail in the project report. In addition, the models were altered so that a standard NOAA magnetic tape of historical meteorological data can be used as data input instead of requiring the user to create a data file. The resulting TRC coal pile drainage model is actually two models - a quantitative model, termed H2OTRC, and a qualitative model, TRCCOAL.

Jan 1, 1984

By Charles Meyer

The year 1955 was a busy one for mining geologists, for the expanding world-wide business activity kept the demand for mining products generally high, stimulating operators to develop local ore reserves and to expand their efforts to find new deposits. The uranium rush was still on, although probably past its maximum rate of climb. Prospecting was also stimulated by the increasing demand for rare metals, and this created new and fascinating targets for exploration. On the whole, it was a boom year when the prospector's chronic optimism found few repressions.

Feb 1, 1956

By Robert E. Green, Kenneth Reifsnider

Several experiments have been performed in order to illustrate the application of a recently developed X-ray image intensifier system to metallurgical investigations. In the present work the system has been used to study the instantaneous alterations in Laue transmission X-ray diffraction patterns during tensile deformation of aluminum single crystals. Expem'mental results are presented which demonstrate the capability of the system for crystal orientation, for following orientation changes due to lattice rotation during tensile deformation, and for showing changes in the homogeneity of the lattice planes along the specimen length as a function of strain rate. RECENTLY, a new X-ray system has been developed which incorporates a cascaded image intensifier and permits direct viewing and recording of X-ray diffraction patterns produced on a fluorescent screen.1"3 In the present work the results of several experiments are presented which demonstrate the usefulness of this system for metallurgical applications. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental arrangement is shown in Fig. 1. In this system a Machlett AEG-50-S tungsten target X-ray tube, normally operated at 50 kv and 40 ma, serves as the X-ray source. The X-ray tube is placed in direct contact with a 10-in.-long collimator, which transforms the X-ray beam from one with a circular cross section to one with a rectangular cross section 3 in. high and 1/6in. wide. By blocking off all but a small portion of the rectangular slit, it is possible to work with the more conventional "pinhole" collimated X-ray beam commonly used for obtaining Laue diffraction patterns. In the present work the test specimens were 99.99+ pct aluminum single crystal wires & in. in diam and 3 in. long. For the deformation tests the wire crystals were mounted in a special set of grips in a table model Instron machine so that diffraction patterns could be recorded during specimen deformation. For the orientation tests the wire crystals were mounted in a rotating goniometer so that diffraction patterns could be recorded during specimen rotation. At a distance of 3 cm from the specimen axis, a 6 in. diam DuPont CB-2 fluorescent screen is positioned to transform the X-ray image to a visible one. A Super Farron f/0.87 72 mm coupling lens, corrected for 4 to 1 demagnification, transmits the visible image to the image tube. The image intensifier used is a three-stage magnetically focused RCA type C70021A with an S-20 input photocathode and a P-20 output phosphor. The tube has unity magnification and useful input and output screen diameters of 1.5 in. The image on the output phosphor is of sufficient intensity to be viewed directly, to be recorded cine-matographically, or to be displayed by vidicon pick-up on a television monitor. The recording device most commonly used is a 16 mm Bolex motion picture camera fitted with a Canon f/0.95, 50 mm lens. The overall gain of the system is 16,000 for direct viewing and 2240 for recording on 16 mm movie film. The resolution of the system is limited to 1 line pair per mm which is approximately that of the fluorescent screen. This system has been used for cine recording of transmission Laue X-ray diffraction patterns with exposure times as short as 1/220 sec and for vidicon television pick-up and display at a scan time of 1/30 sec. Quantitative information may be obtained from each frame of the movie film, by either stopping the vertical slit down to a point source in order to obtain a conventional Laue photograph or else by retaining the linear beam and introducing fiducial marks as described in a previous paper.4 In either case, each frame may be enlarged to appropriate size for analysis by either using a photographic enlarger and making prints of the desired frames, or, more conveniently, by using a microfilm reader. EXPERIMENTAL RESULTS The first series of photographs which are presented in Fig. 2 serves to demonstrate the usefulness of the system for crystallographic orientation determination. This series of prints, made from enlargements of a 16 mm movie film, shows the dynamic Laue transmission patterns produced by an aluminum single crystal wire which was rotating about the wire axis when the patterns were recorded. The movie films were taken at 16 frames per sec and the crystal was rotated at a rate of 15 rpm.

Jan 1, 1970

By K. S. Krishnam, A. G. Guy

VOLUME 6 of the Transactions of the Baikov Institute of Metallurgy, Moscow, is devoted to the subject of "the experimental and theoretical study of the physical characteristics of dilute solid solutions,11 and summarizes work that has been done largely in the years 1958-9. In view of the attention that Soviet investigators have given to this subject, it seemed useful to carry out an independent experimental investigation in an effort to judge the scientific basis and practical significance of this field of study. The present note is a preliminary report of this investigation. The first property studied by the Soviet group was X-ray spectra of solid-solution alloys.' An anomaly observed at low concentrations (--0.05 at. pct) of the alloying element led to the theory that each impurity atom in a transition-metal base alloy is the center of a "block" of affected atoms with a radius of about 10"7 cm. This theory was further developed in a later paper.2 By this time similar anomalies had been found in diffusion coefficients3 and in thermal expansion.4 The entire development up to 1959 was reviewed in a comprehensive paper, and further theoretical ideas were also published at this time. Finally, the volume mentioned above was published in 19607 giving new experimental data on anomalies in optical properties and Hall constant, and a new theoretical treatment also appeared.' Although western scientists have done both theoretical work, summarized recently by Friedel,9 and considerable experimental work on dilute solid solutions, there is little support for the marked anomalies reported in the Soviet papers. Of the physical properties studied by the Soviet investigators, thermal expansion was chosen for the present investigation because of the relative ease of obtaining the necessary precision of measurement. A Leitz dilatometer was used for this purpose, and a special technique involving interchanging of the two specimens being compared permitted a precision of 0.05 x X in average thermal expansion over the range 27° to 600°C. The specimens were heated and cooled in vacuum or in a protective atmosphere at a rate of 50 °C per hr. Ferrovac E iron was used as the comparison specimen and in every case had a coefficient of expansion higher than (or equal to) that of the alloy. Since unintentional impurities are an important factor in studies of dilute alloys, special attention was given to the purity of the iron and the alloys used. The alloys were the same of those used by Abrahamson10 and by Michalak," and their preparation is described in these references. Chemical analyses of the Ferrovac E iron and of typical Fe-W and Fe-Mo alloys are given in Table I. The purity of the iron and alloys is undoubtedly higher than in the

Jan 1, 1962

By Kenneth A. Moon

Kenneth A. Moon (U.S. Army Materials Research Agency)—The authors are to be congratulated for a very interesting and valuable paper. Their discussion of the structural implications of the results shown in their Fig. 5, however, requires a small correction. The model of Speiser and Spretnak with 0 = 1 and z' = 2 is perfectly reasonable for the Ti-O a phase, but Eq. [3] is valid only for solutions sufficiently dilute that the number of empty sites excluded by more than one filled site is negligible. The composition at which intrinsic saturation occurs therefore cannot be deduced from Eq. [3], but but must be decided by consideration of the structural details of the phase in question. In this case, intrinsic saturation is expected not at the composition Ti3O but at Ti2O, because Ti2O has the anti-Cd structurel4 for which each filled octahedral site has two nearby empty sites, one in the hexagonal plane immediately above it, and one in the similar plane below it. The other two models, with ?=1/3 and 1/2, imply a distinction between octahedral sites in pure titanium which is not easy to justify. The problem of extending Speiser's and Spretnak's treatment in a general way to more concentrated solutions will be the subject of a forthcoming publication by the writer. M. T. Hepworth and R. Schuhmann, Jr. (authors' reply)—The authors wish to thank Dr. Moon for calling to their attention the paper by Holmberg which presents the results of X-ray studies of Ti-O solutions ranging from 0 to 33 at. pct 0 and quenched from various annealing temperatures between 400" and 1800°C. Within these ranges, Holmberg found three types of phases: 1) At high oxygen contents (above 25 at. pct) and low annealing temperatures, he found the anti-Cd(OH)2 structure referred to by Dr. Moon. In this structure each titanium atom is in contact with 3 oxygens and each oxygen is in contact with 6 titaniums, the "available" oxygen sites corresponding to every other layer of octahedral sites in the titanium matrix. The limiting composition is Ti2O. However, this anti-Cd(OH)2 structure was not observed for samples containing 25 at. pct 0 or less. 2) For the specimen containing 25 at. pct 0 annealed at 400°C an ordered Ti3O structure was observed. This structure is related to the anti-Cd(OH)2 structure but differs from it by providing only two oxygens adjacent to each titanium atom and thus is consistent with the model represented by Eq. [5] in our paper, with 6 = 1/3, z' = 0. 3) For dilute solutions and for more concentrated solutions annealed at higher temperatures, the structure corresponds to that of the metal with random distribution of oxygens among all the octahedral sites. Thus, it is interesting to observe that the thermo-dynamic indications of ordering in the vicinity of Ti3O can now be supported qualitatively at least by Holmberg's X-ray evidence of the existence of an ordered phase of the composition Ti3O. That is, for solutions with oxygen contents close to that of Ti3O, both the thermodynamic data and the X-ray data are more consistent with models based on the ordered structure of Ti3O than they are with the model which Dr. Moon suggests corresponding to "intrinsic saturation" at Ti2O.

Jan 1, 1963

George W. Maynard, New York, N. Y.:—It is well known that there are many magnetite-mines of which the ore is too low-grade for direct use in the blast-furnace. For carrying out the sintering process, the preliminary step, in the case of magnetites, is the separation of the ore from the gangue by magnetic concentration. The resulting fine-grain product is very objectionable in the blast-furnace, and when used must be a very small percentage of the charge. The sintering process has saved the situation by furnishing a product which is absolutely ideal on account of its cellular structure. (In reply to questions by W. J. Tudor, and Joseph W. Richards, the following additional information was given by Dr. Maynard.) The percentage of iron in the product is determined entirely by the degree of concentration of the raw material and is practically not increased by the sintering operation. The magnetic concentrates at Port Henry and at the Benson and one or two other mines contain from 65 to 67 per cent. of metallic iron. The cost of sintering is from 39 to 41 cents per ton of product, including superintendence, depreciation, and repairs. The itemized figures are about as follows : Mixing (including labor), 24; power, 9; ignition, 5; repairs, 3; total, 41 cents. Prof. J. W. Richards, South Bethlehem, Pa.:—From a metallurgical standpoint I question the accuracy of the statement on p. 374: " C.—An increased reducibility of the iron so treated. (This has been conservatively estimated as 5 per cent. better than the best available ore.)" It seems to me that when a material is' sintered in this way, the constituents present, as lime, silica, and alumina, have a chance to form a compound with the iron oxide; that such a compound, if formed before the material goes into the blast-

Jan 1, 1913

By H. A. Deans

A three-parameter mathematical model for one-dimensional flow in porous media is developed. The objective of the model is to predict accurately the longitudinal dispersion associated with the flow of either gases or liquids over a wide range of Reynolds number. A qualitative analysis of the model parameters is given. Published experimental pulse-response curves are compared with results predicted by the model. Several general types of problems are given for which the model can be used. INTRODUCTION The problem of multicomponent single-phase flow through porous media is encountered in the study of petroleum reservoirs, gas chromatographic and ion-exchange columns, industrial fixed-bed con-tacters and elsewhere. These particular examples span the wide range of flow conditions possible; Reynolds numbers of less than l0-4 are not unusual in oil-production problems, while values in excess of 103 are common in large fixed-bed operations. The study of flow-dependent transport phenomena is complicated both by the changes in the character of the flow over this range, and by the irregularity of the flow boundaries inherent to porous media. Dispersion is one of the important phenomena known to depend fundamentally on flow conditions as well as on fluid and medium properties. As used in this paper, the term "dispersion" refers to the observed mixing of fluid elements of different composition which occurs in flow systems. The actual mechanism may be one or more of a number listed below. Only dispersion in the direction of the mean flow (referred to as axial or longitudinal dispersion, or mixing) is considered here, although lateral dispersion arises as part of certain coupled mechanisms. MECHANISMS FOR LONGITUDINAL DISPERSION A number of distinct mechanisms are known3,5,7,8 to contribute to the phenomenon of longitudinal dispersion. The more important of these are as follows. 1. Molecular diffusion in the flow direction. 2. Turbulent (cell) mixing. 3. Lateral transport processes coupled with velocity and/or residence time distributions, including: (a) "Taylor" diffusion caused by the interaction of velocity profiles in individual voids with lateral molecular diffusion; (b) separation and remixing or interdiffusion of streams having different velocities around particles; and (c) the couplipg of gross velocity profiles, caused by viscous instability or inhomogeneous porosity, with lateral dispersion. 4. Finite mass-transfer rate between a porous matrix and the flowing phase, and finite diffusion rate inside elements of the porous matrix. It is a well documented fact that these mechanisms, whether acting individually or in combinations, produce essentially similar integral effects. The observed dispersion can be described approximately by solutions of the diffusion equation with a properly chosen dispersion coefficient. Necessary conditions for equivalence between dispersion and diffusion are discussed by Klinkenberg and Sjenitzer.7 Apparently these conditions are not satisfied exactly in many real systems. "Best fit" solutions of the diffusion equation often depart appreciably from measured breakthrough curves for the usual pulse- or step-forced experimental systems. In particular, pulse response curves usually show some degree of asymmetry and "tailing" which cannot be reproduced by the one-parameter diffusion model. The three-parameter model proposed herein attempts to produce these effects in a realistic manner. Asymmetry and tailing are predicted for certain sets of parameter values, while for other sets the new model agrees with the diffusion model. VELOCITY DEPENDENCE OF DISPERSION Molecular diffusion apparently controls at sufficiently low Reynolds number in both gas and liquid systems.*l3 At Re > 20, turbulent cell mixing is dominant for gases flowing at low pressure; the data of McHenry and Wilhelm8 show that the mixing cell is approximately 1 particle diameter long in random sphere packs. on the other hand, the data

By Arthur O. Gates

RittingeR's law of the energy expended in crushing is, as roughly stated by Profcssor Richards,' that the work of crushing is proportional to the reduction in diameter; or, as I have more fully expressed it: "The work done in crushing is proportional to the surface exposed by the operation; or, better expressed for this purpose, the work done on a given mass of rock is proportional to the reciprocal of the diameter of the final product—assuming that all the mass has been reduced to one exact sine, which is only theoretically possible."² Kick's law is stated by H. Stadler as follows :3 "The energy required for producing analogous changes of configuration of geometrically similar bodies of equal technological state varies as the volumes or weights of these bodies." In other words, the energy expended is proportional to the volume reduction, instead of the diameter reduction. That these two laws would give widely different results may be shown by a simple imaginary case. A ton of 16-in. cubes is broken to 1-in. cubes at the first operation, and these are broken to 1/16. cubes at a second operation. Since the first operation produces only one-sixteenth as much new surface as the second, the ratio of energy expended in the two operations would be by Rittinger's law as 1 to 16. By Kick's law, since the volume-reduction ratio is the same in both cases, the ratio of energy would be 1 to 1. This discrepancy is great enough to challenge a test by actual experiment, of which there has been, hitherto, but little compared with the amount of argument. The present paper is the record

Jan 1, 1916

By Arthur Gates

INTRODUCTION RITTINGER'S law of the energy expended in crushing is, as roughly stated by Professor Richards,1 that the work of crushing is proportional to the reduction in diameter; or, as I have more fully expressed it: "The work done in crushing is proportional to the surface exposed by the operation; or, better expressed for this purpose, the work done on a given mass of rock is proportional to the reciprocal of the diameter of the final product-assuming that all the mass has been reduced to one exact size, which is only theoretically possible.?2 Kick's law is stated by H. Stadler as follows:3 "The energy required for producing analogous changes of configuration of geometrically similar bodies of equal -technological state varies as the volumes or weights, of these bodies." In other words, the energy expended is porportional to the volume reduction, instead of the diameter reduction. That these two laws would give widely different results may be shown by a simple imaginary case. A ton of 16-in. cubes is broken to 1 -in. cubes at the first operation, and these are broken to 1/16 -in, cubes at a second operation. Since the first operation produces only one-sixteenth as much new surface as the second, the ratio of energy expended in the two operations would be by Rittinger's law as 1 to 16. By Kick's law, since the volume-reduction ratio is the same in both cases, the ratio of energy would be 1 to 1. This discrepancy is great enough to challenge a test by actual experiment, of which there has been, hitherto, but little compared with the amount of argument. The present paper is the record

Jan 9, 1915

By A.J. PHILLIPS, Wm. B. Price

ADMIRALTY nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Win. B. Price1 described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.2 A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm.. Gallimore & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four, binary copper-nickel alloys of the compositions shown in Table 1. Various amounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by melting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of these castings was polished and etched for-examination. The castings were not homogeneous solid solutions, but showed the usual cored structure associated with cast alloys. However, from an examination of these sections we roughly determined

Jan 1, 1928

By Henry W. Edwards

Concrete is not a new, nor even a modern substance. Important structures built by the old Romans before the commencement of the Christian Era are to-day sound and solid— for example, the dome of the Pantheon in Rome, 142 ft. in diameter. I do not propose, therefore, to discuss the durability of the material, as in the mining and metallurgical business, structures, as a rule, are not calculated to endure for two thousand years. I do wish to urge, however, that much of the stone masonry around mines and smelters would have given better results if concrete had been used in place of stone. Concrete looks better; is stronger, cheaper, more durable, more quickly built, and above all requires no skilled labor, except that of the carpenter, who, like the poor, is always with us. Well proportioned concrete, that is to say, having well proportioned ingredients, may be safely relied upon to withstand a compressive or crushing strength of 50 tons per square foot. In most American cities, however, the building laws limit it to the absurdly low figure of 16 tons. This restriction is probably due to the political influence of the building-trades unions, which object strongly to its too free use, undoubtedly owing to its not requiring the services of skilled workmen. I hope to show that quite important construction work may be' undertaken without the aid of the gentleman with the trowel. In some of the isolated districts of the West and Southwest this is no mean advantage. The weight of good concrete, dry, is from 130 to 160 lb. per cubic foot. Ingredients of Concrete. Concrete is composed of four ingredients; viz., 1. Crushed Stone; 2. Sand; 3. Cement; and 4. Water.

Jan 1, 1905

By A. J. Phillips, C. G. Grant, Wm. B. Price

ADMIRALTY nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Wm. B. Price1 described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.2 A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm. Gallimore & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four binary copper-nickel alloys of the compositions shown in Table 1. Various amounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by melting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of these castings was polished and etched for examination. The castings were not homogeneous solid solutions, but showed the usual cored structure associated with cast alloys. However, from an examination of these sections we roughly determined

Jan 1, 1928

By Walter L. Maxson, Fred C. Bond

There is more information contained in a screen analysis than is ordinarily recognized, and there is an increasing need for methods of making this additional information easily available. As more comprehensive studies of crushing and grinding are made, and as the possibilities of decreased expense and increased extraction through a closer control of grinding are explored, methods of interpreting screen analyses assume an importance which they have not had heretofore. The information commonly desired, which can be determined from a complete and carefully made screen analysis, includes: (1) the size distribution of the material passing the finest screen, (2) the presence of a hard grinding fraction, (3) the location of natural grain sizes, (4) the presence of different materials with markedly different grinding characteristics, (5) the presence and amount of finely divided material such as clay, which is merely unlocked in grinding, and (6) the total surface area of the ground product. It is necessary to know the fundamental law of size distribution of a homogeneous material in order to correctly resolve a screen-analysis curve, and to understand the variations and anomalies that a sample may exhibit when compared with the ideal curve. This fundamental law was developed by Gaudin,1 who showed that when the logarithm of the per cent weight retained on any screen and passing the next larger screen in the Tyler standard screen scale was plotted against the logarithm of the screen aperture the resulting curve for the finer sizes of a homogeneous crusher or grinding-mill product would be a straight line. Gross and Zimmerley2 experimentally confirmed Rittinger's law, which states that the useful work done in crushing a homogeneous material is directly proportional to the new surface area produced; and showed that in the larger screen sizes resulting from impact crushing a

Jan 1, 1935

By J. A. M. van Liempt

Since the discovery of von Laue, that a crystal forms a natural grating for X-rays, our knowledge of the structure of solids has gone forward with rapid strides. This progress is not only of purely scientific interest, but has also yielded direct technological results. One of the most valuable results is the broadening of our knowledge of the structure of pure metals and alloys. To promote these studies it is often desirable to have at our disposal pieces of metal consisting of one single crystal. As is so often the case in the natural sciences, we obtain the best results by making our earliest experiments on pure, simple materials and avoiding unnecessary complications. The Cryogen Laboratory at Leyden followed this method with much success, because the work was done at such low temperatures that the heat movement of the atoms was almost absent. Similarly we can simplify the studies of metals by leaving out of consideration the influence of the grain boundaries and the mutual influence of the crystals by using unicrystalline instead of polycrystal-line metal. Methods of making single crystals have been scientifically studied during the past few years. Some methods were already known in the arts, but these have been improved and new methods have been developed. The methods for making metallic single crystals may be divided into the following groups: A. From the liquid state B. From the gaseous state C. Electrolytically D. By recrystallization in the solid state Method A 1. Tamwmnn's Method1—Tammann succeeded in making bismuth single crystals of a maximum length of 20 cm. by undercooling the molten metal 0.1 to 0.3' G. below its melting point in glass tubes of a maximum

Birmingham - A City With a Future COURTING new industries is the time honored duty of the chambers of commerce; but Birmingham, until recently, has done its courting without the benefit of troubadors. This is all changed now for the iron and steel industry is singing an enticing song about steel priorities for new industries from Birmingham's own mills. Along with the increasing industrialization of Birmingham there has been a marked influx of industry into the Southeast and neighboring areas in the south central states which augurs well for business in Birmingham. This important stronghold of the foundry industry (consuming 95 pct of Birmingham's merchant pig iron in 1950) has been the source of important announcements about additions to steel ingot capacity. The virtual abolition of basing point pricing gives the Birmingham iron and steel industry an advantage in the South's new markets. This means more business for Birmingham, but the problem of raw materials supplies is posed.

Jan 12, 1950

By A. H. Lindley, Fraizer M. Stewart

For many years large mining companies were able to finance nearly all of their capital requirements from internally generated funds. However, during the last decade, funds needed for capital expenditures, dividends, and scheduled debt retirement have grown faster than cash flow. As a result the minerals industry has had to rely increasingly on other sources of funds. Getting the capital for new mining projects is a challenge, particularly for smaller companies. New methods of financing and new variations to old methods have been developed and more are needed. Commercial banks are short-term lenders. By policy their loans are limited to low risk loans-those made solely on the borrower's general credit, and secured loans where cash flow is sufficient to provide repayment within a comparatively short term. To maintain liquidity, banks prefer to make loans of less than seven years' term. If a longer loan is needed an insurance company or pension trust may take the long-term part.

Jan 1, 1971