Search Documents

Recent start-up of a new 3450 t/d (3800 stpd) copper-zinc concentrator complex in northern Manitoba, Canada, is expected to open new reserves and dramatically cut transportation costs for Hudson Bay Mining and Smelting Co.'s Snow Lake operations. The new $C33-million mill is located in Stall Lake, Manitoba, and includes a new crushing and grinding facility and two flotation circuits for the production of 23-25% copper and 55% zinc concentrates. A small amount of lead concentrate will also be recovered. The plant will produce some 145 000 t/y (160,000 stpy) of concentrates, to be shipped by rail to the firm's Flin Flon copper smelter and zinc refinery complex, located 177 km (110 miles) to the west on the Saskatchewan-Manitoba border.

Jan 9, 1979

By T. lkeda, R. S. Montgomery. A. Hara

Actual test specimens used in the previous laboratory wear investigation,' were fully characterized and the data is given in Table 1. Most of the carbides tested could be placed into groups of similar mean grain size. When the wear rates of the members of these groups were plotted as functions of their hardnesses, a family of curves resulted; curves for groups containing data from larger grained composites were at lower wear rates at the same hardnesses. Most specimens tested showed only A-1 porosity (ASTM Standard designa-

Jan 1, 1971

By D. M. Hausen

The amenability of a given vanadium ore to any given treatment depends largely on the mineralogic combinations of vanadium in the ore. Quantitative data on vanadium mineralogy provide not only an objective basis for selection of proper treatment, but also may eliminate many time-consuming amenability studies whose results are empirical, at best. Vanadium is distributed through the interstices of mineralized sandstone ores in the form of oxidized vanadates, reduced oxides, and silicates. Oxidized vanadates, e.g., carnotite, tyuyamunite, etc., are most readily beneficiated by simple acid leaching. Reduced oxides are more slowly solubilized, but relatively amenable to most acid treatments. The layered silicates, roscoelite, mixed layered mica-montmorillonite, and chlorite, are least amenable to most acid extractions, and constitute an assemblage of vanadium- bearing clays that are common to many sedimentary deposits. Vanadium is combined principally as layered silicates in the clay fractions of many sandstone ores. Mineralogic studies in this paper are largely confined to clay minerals, and to their amenability characteristics in low pH liquors.

Jan 1, 1985

By A. Eilers

A number of the copper refineries in this country have lately separated some of the rarer metals from the slimes in the refinery tanks. One of these has furnished me the following table of recoveries from given amounts of blister. I publish this to show the proportions, to gold and silver and to each other, in which these rarer metals may be expected to occur in copper from certain localities. GarFIeld, Utah :—The blister copper comes principally from the Bingham porphyry copper mines. Steptoe, Nev. :—All the blister copper is produced from the Nevada Consolidated mines. (Also porphyry deposits.) Omaha, Neb. :—Blister copper comes principally from concentrated copper-lead mattes shipped from the different lead-silver plants of the Rocky Mountain region to the converters at the Omaha lead refinery. Mountain, Cal. :—Ores occur in connection with diorite (?).

Jan 1, 1914

By B. A. Joyce, R. W. Bicknell, R. J. Bennett, P. J. Etter

Epitaxial layers of silicon have been grown on single-crystal quartz and alumina by two types of chemical reaction the hydrogen reduction of trichlorosilane and b) the pyrolysis of silane. These reaction systems are described. The cqsfallography of the two systems, as determined by electron and X-ray diffraction, is discussed, and epitaxial mechanisms suggested. The electrical behavior is briefly considered, and the design and properties of field-evert devices fabricated in the epilaxial material are also discussed. RECENT work carried out in these laboratories" has shown that it is possible to obtain epitaxial deposits of silicon on single-crystal quartz and alumina. The purpose of this paper is to describe the method of preparation of these layers using both the hydrogen reduction of trichlorosilane and the pyroly-sis of silane, to compare the crystallographic behavior of films on the two substrates, and to present some initial results of the electrical behavior of silicon layers on alumina. The structural study has been carried out using electron and X-ray diffraction and electron microscopy. The electrical assessment has been made in terms of conductivity and mobility determinations by the van der pauw3 technique, and by measurements on metal-oxide-semiconductor assemblies. 1) FILM PREPARATION Both quartz and alumina substrates, approximately 1 sq cm in area and 0.4 mm thick. were prepared from slices cut parallel to within a few degrees of (11.0), (10.0), and (00.1), and polished mechanically down to about 0.3 p diamond grade. Chemical polishing of alumina slices, using phosphoric acid at elevated temperatures, has also been used; epitaxial silicon layers have been grown on these substrates, but the process is not entirely reliable, possibly because the large strain present in the Verneuil-grown alumina crystal affects the chemically prepared surface. The two reaction systems are fairly conventional and are described briefly below. a) Trichlorosilane-Hydrogen System. The apparatus is shown schematically in Fig. 1. The substrate was heated by induction, with a fused-quartz encapsulated graphite hemicylinder as susceptor. The procedure for carrying out a deposition was to heat the substrate to reaction temperature in a stream of

Jan 1, 1965

By John Charles

The Engineering Method. By John Charles Lou11sbul.y Fish. Stanford University Press. 1950. 186 P. $3.-This book is about the "professional habit often referred to . . . . as 'the scientific method' . . ." It formulates for students the system of logic and reasoning that is the mark of the practicing engineer. The three chapters are, "The Method of Engineering", "Application of the Engineering Method" and "Uncertainties in Engineering." They cover logic and reasoning, terms, nontechnical problems, practical conditions controlling the engineering method, inescapable uncertainties and the method of coping with them. The author is emeritus professor of civil engineering at Stanford. The material presented here formed chapters 9, 10, and 11 of The Engineering Profession, by Hoover and Fish, second edition 1950. Elements of Ore Dressing. By Arthur F. Taggart. John Wiley & Sons, Inc., New York, 1950. $10.- A modern and practical introduction to the subject by the noted author of the Handbook of Mineral Dressing. The philosophy that a mill and all its parts comprise a single treatment process is a continuing theme in the book. Professor Taggart covers hand picking, screening, filtration, and electrical concentration. After introducing sedimentation, he takes up acceleration in free-settling, hindered-settling, sink-float, jigging, film and trough concentrators and shaking concentrators. A discussion of organic chemicals in flotation is followed by a detailed treatment of flotation. Final chapters deal with primary crushing, secondary crushing, grinding, transport, and controls and flowsheets.

Jan 3, 1951

By Thomas H. Sheehan

The purpose of this paper is to present an application of computer technology to assist the mineral company financial executive in assessing exchange risks. The paper is divided into five parts: Background, Translation Approaches, Theory, Empirical Validation, and Conclusion. BACKGROUND Exchange risk results from a change in the rate of exchange between a host and a home country's currencies. Legitimate reasons exist for changes in the currency exchange rates among countries in a world with over a hundred different currencies. These reasons include: different economic growth rates, social factors, cultural heritages, and political motivations. The problem of exchange rate changes are perennial and exist whether the world operates on exchange rates or floating exchange rate practices. The cause of the problem is trade and international payment imbalances. If one accepts the premise that exchange rates fluctuate over time, then the mineral company financial executive faces a continual process of reassessment of the impact of exchange rate changes on the financial worth of his company. (1) The mineral company financial executive prepares balance sheets and income statements that are audited by certified public account- ants annually for shareholders, bankers, and tax authorities. The financial executive translates assets and equities denominated in foreign currencies into domestic dollars, e.g., Japanese firms convert to Yen, French firms convert to Francs, and so on. When figures from foreign subsidiary operations are consolidated into the balance sheets of the parent corporation, estimates of the company's finan-

Jan 1, 1977

By E. H. Cho

INTRODUCTION Activated charcoal has been used for several centuries in many capacities including the recovery, isolation and purification of various materials (1). The first use of charcoal in a gold metallurgical system was in the extraction of gold after chlorination (2, 3,4). The gold was dissolved in a chlorine system and subsequently filtered through charcoal. The application of charcoal with cyanide extraction was patented by Johnston (5) in 1894 and adopted commercially in Australia in 1897. The process consisted of dissolving the gold and silver in a potassium cyanide solution and passing it through a series of charcoal filters. The charcoal was subsequently smelted to recover the gold and silver. The interest in the use of charcoal diminished in the first part of the twentieth century as the practice of the use of zinc as a precipitating agent increased. However, in 1916, the Yuanmi Mine in Australia replaced their zinc precipitation plant with a charcoal adsorption plant. In 1926, Scott and Gross (7) of the U. S. Bureau of Mines con- ducted extensive research on the adsorption of gold and silver from cyanide leach solutions. Among their findings was the result that the most important factor in improving the adsorptive power of charcoal was heat treatment with oxidation by air or steam. The work of Zadra (8) in 1952 stimulated renewed interest in the use of activated charcoal in gold and silver recovery with the development of a method of recovery of the gold and silver from the charcoal other than its destruction by burning. The process involved simultaneous desorption

Jan 1, 1983

By Graham P. Crutchfield

The W. I. Cook pool in Shackelford County, Texas, has been the subject of a number of papers and articles. Its unique position both as to operation and development has made it an ideal location for unit repressuring. The major portion of the pool is located on the W. I. Cook ranch and most of the oil leases are owned by Roeser & Pendleton, Inc. and the Continental Oil Co. and operated by Roeser & Pendleton, Inc. The Humble Oil & Refining Co. and Tom James operate producing leases which have a vital bearing on the unity of the pool. Both have cooperated in the repressuring project. Practically the entire royalty is owned by Mrs. W. I. Cook and she has given the operators her entire cooperation in all phases of unit repressuring.

Jan 1, 1931

By J. W. Dougherty

THE Hollinger gold mine is in the Porcupine mining division, District of Cochrane, in the northern part of the Province of Ontario. The adjacent town of Timmins, with a population of 25,119, lies 490 miles by railway north of the city of Toronto. GEOLOGY The property is situated on the northwest limb of a major syncline, which pitches northeast at approximately 50°. The principal rocks of the Hollinger area are of pre-Cambrian age and consist of altered, schistose, Keewatin lava flows intruded by stocks of schistose, quartz-feldspar porphyry generally assigned to the Algoman period. The structure of the Keewatin series is extremely complex as a result of close folding and some faulting. The schistosity, trending north 70° east and dipping steeply to the southeast, is most highly developed along a subsidiary anticline in which the major porphyry bodies occur. The ore bodies, which exhibit three principal structures, consist of quartz veins and associated pyritized wall rock. Some lodes are com-posed of en echelon veins, others exhibit a main quartz body with branch-ing stringers and a third consists of a single definite lead. Gold, in a coarse visible form, may be confined to quartz in some ore bodies but in others it is finely divided and is found not only in quartz but also asso-ciated with pyrite in the adjacent wall rock. In many veins the dis-tribution of gold is such that there are several ore sections, separated by areas of low-grade material, in the same vein although its physical appearance remains unchanged.

Jan 1, 1940

By F. N. Rhines, B. H. Alexander

MUCH attention has been directed to the effects of grain size upon the properties of alloys, but there has been scant study either of the conditions that determine the pattern and dimensions of den-drites in metal systems, or of the influence of their shape and size upon the overall properties of cast-ings. The aim of the research that is about to be described has been to investigate the effect of vari-ous factors upon the mode of formation of dendrites in alloys by measurements of the distance between adjacent dendrite arms (dendrite spacing). Early investigators, including Grignonl and Tschernoff,2 showed that a metal dendrite is com-posed of a tree-like system of stalks and branches arranged in a simple geometrical pattern. North-cott and Thomas3 demonstrated that, in the face-centered cubic solid solutions of copper-base, these stalks and side arms all lie in (100) directions in the crystal. Several investigators, including Sauveur and Chou,0 Sauveur and Reed,' and Martin and Mar-tina have reported that the addition to steel of alloy-ing elements, such as nickel, chromium, and molybdenum, not only makes the dendrites easier to reveal by etching, but makes them coarser. The latter authors8 proposed that the coarsening of the dendrites is roughly proportional to the increase in the temperature range of freezing, caused by adding the alloying elements. Sauveur and Chou6 showed, in addition, that the dendrites are coarsened by a decreased rate of cooling of the casting. Measurement of Dendrite Arm Spacing Among the physical conditions that could be ex-pected to have an influence upon the dendrite arm spacing, that appears in a cast metal, are: composi-tion, rate of freezing, crystal structure, and type of constitution. The relationships obtaining between these variables and the dendrite dimensions have been examined, in the present research, by measur- ing the arm spacing in a wide variety of alloys, listed in tables II through VI. Alloy compositions are recorded in the tables by showing the symbol of the major metal followed by the percentage and symbol of the alloying agent; thus, "Al-10Ag" is an aluminum-base alloy containing 10 pct of silver. Although none of the alloys were analyzed, an im-pression of their degree of purity may be obtained from that of their component metals given in table I. Five hundred grams of each alloy was made by melting in small clay-graphite crucibles in an elec-tric muffle furnace. After alloying the temperature was adjusted to 50" to 75°C above the liquidus and the melts were poured into cast iron molds, at room temperature, the molds having a wall thickness of 1 in. and a cavity 11/2 in. sq in cross-section. Each ingot, thus cast, was sectioned at mid-height and the sectioned surface was polished and etched for metallographic examination. Dendrite spacing meas-urements were made at three positions, namely, ad-jacent to the mold wall, midway between the wall and the center of the ingot, and at the center (desig-nated e, m, and c respectively, in the tables). A typical series of microstructures is presented in fig. 1. For each measurement, the average was taken of the dendrite spacing of several grains covering a zone about 2 mm wide. Only those grains which had a major dendrite axis nearly in the plane of polish were selected in order to eliminate corrections for orientation differences from grain to grain. Although the dendrite spacings were measured to the nearest thousandth of a millimeter, the values listed in the tables are thought to be significant only to the nearest hundredth of a millimeter. The larg-est difference in readings found, when various ob-servers rated the same specimens, was 0.012 mm; the largest difference between corresponding meas-urements upon duplicate specimens was 0.027 mm.

Jan 1, 1951

By Ian Campbell

THE year 1952 was marked by several new alltime highs in industrial mineral production; by an easing of the critical situation with respect such minerals as fluorspar and sulphur; by important production of asbestos, lithium, and rare earths; by the perfecting of new products which will place new demands upon industrial mineral supplies, such as "Fiberfrax", and the finding of new uses for old minerals, such as wollastonite; by continuation of basic and applied research; and publication of a notable study of the national mineral economy, viz., the "Paley Report".

Jan 2, 1953

By R. E. Ogilvie, J. I. Goldstein

The a and y solubility limits in the Fe-Ni phase diagram have been redetermined at temperatures above 500°C. Both a diffusion-couple and a quench and anneal technique were used. The solubility limits were measured with an electron-probe micro-analyzer. The nickel concentration at the phase boundary is increased below 700°C and the a solid-solubility range is much larger than had been previously measured. The solubility limits are also extrapolated to 300°C. It is suggested that the solubility of nickel in a FeNi reaches a maximum in the temperature interval 400o to 500°C. THE equilibrium diagram has been of great use in the field of meteoritics, where the phase relations between kamacite (a) and taenite (?) in metallic meteorites can be described by means of the Fe-Ni diagram. The study of metallic meteorites by electron-probe microanalysis has cast some doubt on the accuracy of the presently available Fe-Ni diagrams.1, 2 Recent thermodynamic studies of the Fe-Ni system also suggest that the diagram may be in error.3 For these reasons the high-temperature (800o to 500°C) part of the diagram was redetermined. INTRODUCTION The currently accepted Fe-Ni diagram is that of Owen and Liu.4 Above 910°C, there is a region of complete solid solubility, ? (fee). Below 910°C, the a (bee) phase is stable in pure iron. The effect of increasing amounts of nickel is to stabilize the y phase. The phases that form when Fe-Ni alloys are heated or cooled bear little relation to the equilibrium diagram. If an alloy is cooled from the y state and held at a temperature within the a + y field, no evidence has been found for the occurrence of the y - a transformation.5 If the alloy is cooled to low enough temperatures the y phase breaks down into a supersaturated bee phase called a2. In fact, in alloys over 27 pet Ni the y phase is retained at room temperature.6 The a, phase has the same composition as the original y. The temperature at which a2 forms, the M, temperature, has been determined experimentally.' A state of equilibrium can be approached by cooling below M, to form a2 and then reheating the alloy into the two-phase region of the diagram. The y phase will then begin to precipitate out of the a2 phase and grow. The growth of the phase, however, is quite slow. Using the interdiffusion coefficients -Da of Goldstein et al.,8 it is estimated that it takes about 1 year to grow a 10-µ-wide region of ? at 700°C in a 5 pet Ni alloy. Owen and Liu4 used the technique just described to form the equilibrium phases. The phases present were determined by means of X-ray analysis. The accuracy of their diagram depends on the number of alloys available near the phase boundary at a given temperature. In this study two different techniques were used to determine the a/a + ? and ?/a + ? solubility limits. The inherent accuracy of both techniques was greatly improved over that used by previous investigators because the phase-boundary compositions were measured with an electron-probe microanalyzer. PROCEDURE The two methods used to determine the Fe-Ni diagram are the diffusion couple (D.C.) and the quench-and-anneal (Q.+A.) techniques. In the first method, diffusion couples whose diffusion path goes through a two-phase region of the phase diagram were used. A description of the technique used for making the diffusion couples has been described in a previous paper.' After the diffusion treatment a discontinuity in the resultant concentration vs distance profile was measured. The nickel concentrations in the a and ? phases at the interface of the discontinuity are the solubility limits of the a and ? phases in the phase diagram at the diffusion temperature. If the interface com-

Jan 1, 1965

By E. F. Johnson, F. H. Brinkman, H. J. Welge, A. L. Hicks

A method is presented for predicting the character of gas or water displacement in a radial system, which can be either horizontal or inclined. The latter case would comprise cone-shaped or dome-shaped symmetry. The method conriders the one dimension of radial distance, taken parallel to the bedding planes. Approximate allowance can be made for segregation of the two fluids perpendicular to the bedding planes. A complete saturation history can be obtained in about a day's time with the use of a desk calculator. Results of an example calculation agree well with the performance of simulated gas drive in a large model representing a section of a cone. This pie-shaped, sand-packed model was 8-ft long and 4-in. thick. The method of solution is useful in handling other partial differential equations of first order and first degree. INTRODUCTION A new analytical method has been developed for predicting the performance of gas or water drive in a reservoir having radial or cone-shaped symmetry (see Fig. 1). In addition, this new development offers a general method of handling partial differential equations of first order and first degree. This work extends those methods developed previously'- "or predicting the displacement of oil by gas or water in linear systems. The method of calculating oil recovery in a radial system involves two major parts. The first part is a calculation of the distribution of saturations at various times of depletion. The second part is the calculation of oil recovery and producing gas-oil or water-oil ratios through volumetric balance on the saturation distributions obtained in the first part. This second part differs only slightly in principle from similar calculations made with linear systems, for instance. The basic assumptions used in the calculations are as follows. 1. One-dimensional radial flow. An approach is explained later for approximating a second vertical dimension. (With- drawals of oil, and of the driving fluid after breakthrough, are assumed uniform around the periphery of the dome.) 2. Constant-volume fluid flow. Thus, in a gas drive there is no change in gas solubility, or in oil or gas volume due to viscous and gravity pressure drops. 3. Capillary forces are negligible. 4. Constant rate of injection. A program has been written for carrying out the calculations needed on a digital computer. However, a prediction can also be arrived at using a desk calculator; this latter method of work requires about a day's time for each prediction made. CALCULATION OF SATURATION DISTRIBUTION For definiteness, we describe the development of our method for the case of gas drive from the crest of the structure. The reader will note, however, that the method is just as applicable to an advancing radial water drive. The equation describing gas flow over an infinitesimal

By TRUMAN S. FULLER

THE GREAT INTEREST in decomposition and trans- formation, so evident in the study of alloys during the last two years, was reflected in the many papers on this subject, presented at the first session of the Institute of Metals, Tuesday morning. Dr. F. A. Thomson, of Montana State School of Mines, presented the first paper by C. Wilson, H. F. Silliman, and E. C. Little, "Rate of Precipitation of Nickel Silicide and Cobalt Silicide in the Hardenable Copper-nickel-silicon and Copper- cobalt-silicon Alloys." Dr. R. F. Mehl, in discussing this paper, stated that the title was somewhat deceptive, as it indicated that the rate of precipitation is determined; the method used is a measurement of electrical conductivity and hardness, neither of which is suitable for a quantitative measurement of rates of reaction or precipitation in the solid state. Hardness is also uncertain because it depends so much upon particle size. Of the various methods proposed for the study of rate of reaction and precipitation the evaluation of volume of reaction produced from the area of photomicrograph is the best.

Jan 1, 1933

By C. Erb Wuensch

The Eagle mine is situated in the Kerber Creek mining district, Bonanza, Saguache County, Colo. The climate and topography of this district arc similar to those of mining camps of the Rocky Mountain region that lie 9000 to 12,000 ft. above sea level. The district is at the northeasterly edge of the San Juan volcanic region, in which successive Tertiary lavas have built up a high plateau resting upon earlier sedimentary formations, or the underlying pre-Cambrian complex. The latter was exposed in places by erosion previous to the eruptions. In the Bonanza district, proper, only volcanic formations, andesites and latites, are found. Dr. H. B. Patton,1 in his survey of the district, discriminates between several varieties of lavas and maps these as distinct flows. They are local variations within the same lava and it is impossible to determine any distinct line of demarkation between them. Structurally they are members of the same flow. There are three general types of vein occurrences: 1. Lead-zinc-copper-silver-gold veins in well-defined fissures with a quartz gangue; ill these, the various sulfides show a zonal arrangement. 2. Massive gray copper ores high in silver, in irregular fractures in the form of small lenses and pockets, in which little or no quartz is found. 3. Manganiferous quartz veins very low in silver and gold at the surface which, with depth, become important silver veins containing subordinate amounts of gold. These veins have a quartz gangue with an abundance of Phodochrosite. The silver is associated with small amounts of sphalerite, galena, and pyrite; fluorite also is present. The Eagle is the only mine that has been developed in the manganiferous quartz type of vein. It was discovered ill the fall of 1582, but little more than assessment work was done on the property for a number of

Jan 1, 1923

By C. Erb Wuensch

The Eagle mine is situated in the Kerber Creek mining district, Bonanza, Saguache County, Colo. The climate and topography of this district arc similar to those of mining camps of the Rocky Mountain region that lie 9000 to 12,000 ft. above sea level. The district is at the northeasterly edge of the San Juan volcanic region, in which successive Tertiary lavas have built up a high plateau resting upon earlier sedimentary formations, or the underlying pre-Cambrian complex. The latter was exposed in places by erosion previous to the eruptions. In the Bonanza district, proper, only volcanic formations, andesites and latites, are found. Dr. H. B. Patton,1 in his survey of the district, discriminates between several varieties of lavas and maps these as distinct flows. They are local variations within the same lava and it is impossible to determine any distinct line of demarkation between them. Structurally they are members of the same flow. There are three general types of vein occurrences: 1. Lead-zinc-copper-silver-gold veins in well-defined fissures with a quartz gangue; ill these, the various sulfides show a zonal arrangement. 2. Massive gray copper ores high in silver, in irregular fractures in the form of small lenses and pockets, in which little or no quartz is found. 3. Manganiferous quartz veins very low in silver and gold at the surface which, with depth, become important silver veins containing subordinate amounts of gold. These veins have a quartz gangue with an abundance of Phodochrosite. The silver is associated with small amounts of sphalerite, galena, and pyrite; fluorite also is present. The Eagle is the only mine that has been developed in the manganiferous quartz type of vein. It was discovered ill the fall of 1582, but little more than assessment work was done on the property for a number of

Jan 1, 1923

By R. D. Carpenter, R. R. Smith, E. E. Sougstad

The Union Carbide Nuclear Co., in treating low-grade tungsten and molybdenum-copper ores at the Pine Creek mill near Bishop, Calif., employs flotation for the initial extraction of the valuable mineral constituents. These minerals consist of scheelite, molybdenite, and several of the copper sulfides including chalcopyrite, bornite, and possibly chalcocite. They occur in a gangue consisting mainly of quartz, pyroxene, and garnet, with minor amounts of calcite and fluorite. This assemblage of minerals presents an unusual grinding problem because of their diverse physical characteristics. Feed for the circuit is prepared from -6-in. ore by screening on a rod deck screen to remove the -5/8 - in. material. The+5/8-in. fraction is crushed in open circuit with a 5 1/2-ft Symons shorthead crusher operated at a closed- side setting of approximately 3/8 in. The screen undersize and the conecrusher discharge are then combined to constitute the feed to the grinding circuit. The ore is ground in 6 by 5-ft grate discharge ball mills operated in closed circuit with 54-in. spiral classifiers. The classifier overflow goes directly to the flotation section of the plant. Studies of the flotation circuits have shown that the maximum recovery of the tungsten, molybdenum, and copper minerals occurs in the particle-sue range from 100 mesh to approximately 400 mesh. Further, practice has shown that the ore minerals are effectively reduced to this size range if the total ore is ground to -48 mesh. The general objective of the grinding circuit then is to reduce the feed to -48 mesh with the production of a minimum amount of slimes. The purpose of this investigation was to ascertain how well the grinding circuit was carrying out this objective. The method used was to sample the various products in the grinding section, size these products accurately, and analyze the resulting sue distributions. SAMPLE PREPARATION AND SIZING TECHNIQUES Representative samples of the different grinding circuit products, namely, new feed to the ball mill, ball mill discharge, classifier overflow, and classifier return, were taken over a 24-hr period. The samples were then dried without being filtered to avoid loss of slimes. The percentages of solids in the different products were the following: new ball-mill feed, 95%; ball mill discharge, 82%; classifier overflow, 52%; and classifier return, 84% solids. Particle sizes were determined on each product by wet-screening an

Jan 1, 1962

By John A. THOMPSON, Pazcl D. Torrey, Frank Breayster

DISCOVERY of natural gas in the Dundee field of New York in February, 1930, and the subsequent discovery in Tioga in September of that year, focused the attention of the natural-gas industry on the enormous possibilities of production and distribution in - the most populous area of the United States-New York and New England. Prior to 1926 the natural-gas industry in New York State had settled into a definite and limited policy, with the distributing companies controlling the output from its discovery to the ultimate consumer. Production amounted to between G and 7 thousand mil- lion cubic feet a year, with another 10,000 million feet imported from Pennsylvania for distribution in New York State. This gas was primarily from the Medina sand stone in. the western part of the state.

Jan 1, 1932

By W. McA. Johnson

THE work of J. E. Johnson, Jr., on the effect of small amounts of oxygen in cast iron in increasing its strength and resistance to shock, is of interest from the technical and scientific standpoints. The following exposition of the theory carries Mr. Johnson's explanation further and, in my opinion, will disclose certain related phenomena and perhaps shed further light on the subject. Some facts, so novel in character as to excite incredulity, have been accepted finally by many metallurgical authorities. One of these is that oxygen to the amount of 0.060 per cent. in cast iron gives it a breaking strength of 3,500 lb. per square inch, compared with a breaking strength 2,500 lb. per square inch in cast iron of the same composition with re-ect to elements other than oxygen, but having only 0.010 per cent. oxygen. The "oxygenated" cast iron, even if made in a coke furnace, has properties equivalent to the best charcoal pig iron. Mr. Johnson has also established the fact that the variations in combined carbon cannot account for the results. By microphotographic evidence he has shown that in oxygenated cast iron the graphite particles are dense and spherical, while in well-deoxidized cast iron the graphite particles are flaky and leaf-like. It is just a matter of common sense that iron of the latter structure is much weaker than the former. The analytical and microscopical work has been done with care and there is no doubt in my mind about the accuracy of the, experimental results. In this paper then, we shall consider it as accepted that small amounts (0.060 per cent.) of oxygen increase the strength of cast iron by producing a structure in which the round and solid particles of graphite are surrounded firmly by a principal matrix of ferrite. The purpose of this paper is to show that the reason why the graphite particles are round is founded on the fact that the particles of any precipitate are made denser and harder by the presence of a reagent having a solvent action on the precipitate. This can be stated as a law, although I have never seen it so given in any textbook.

Jan 2, 1916