Search Documents

By G. B. Pryde

IN laying out a new mine, provision should be made for the ultimate recovery of as much coal in any given bed as is consistent with safety and economic mining. Though each mining district, if not each individual mine, has problems that make the adoption of any hard and fast rule impossible, certain basic principles are adapted to practically all conditions. One of the most vital is the provision for barrier pillars of ample dimensions to protect all haulage and permanent airways during the life of the property. Where conditions permit, room or butt entries should be driven on the strike or slightly to the raise and rooms turned at right angles to said entries. The width of rooms and room pillars is governed by conditions prevailing in the mines under consideration. A safe rule is: In advancing, extract not more than 25 to 35 per cent. of the entire seam; in exceptionally thick seams, considerably less than 25 per cent. should be taken. Rooms usually vary in length from 250 to 350 ft. (76 to 106 m.) with a barrier pillar of not less than 80 ft. between the last crosscut in rooms, and entry and room crosscuts should be driven on sights; room crosscuts should be driven at right angles to the direction of the rooms. In mines under excessively heavy cover or where roof conditions are bad, rooms should be driven narrow and a barrier pillar left at every fifth to tenth room. This barrier should be of such dimensions that one or more rooms, with pillars of usual dimensions, may be turned through it when the barrier is no longer required. Two of the advantages of such a barrier are the protection of the panel against peaking of roof load during pillar extraction and the easy closing of the entry in case of fire.

Jan 2, 1921

By F. G. Loper

Simulation as a mathematical technique is not new. However, recent increases in digital computer speeds and the ease of programming with languages such as Fortran have centered a good deal of attention around simulation in the last few years. By ignoring all but the relevant characteristics of a process, a mathematical simulator may be constructed which, when fed operating data, should react as the process would. The output becomes numbers, instead of tons, however. Thus, a trial-and-error operation of such a simulator will permit management to study a major system change at little cost.

Jan 1, 1967

No. Place Date Vol. 1. Wilkes-Barre, Pa May, '71 1 2. Bethlehem. Pa Aug., '71 1 3. Troy, N. Y Nov.,'71 1 4. Philadelphia, Pa Feb., '72 5. New York, N. Y.* May, '72 8. Pittsburgh, Pa Oct., '72 7. Boston, Mass Feb., '73 8. Philadelphia, Pa.* May, '73 9. Easton, Pa Oct.. '73 10. New York, N. Y.Feb., '74 11. St. Louis, Mo.* May, '74 12. Hazleton. Pa Oct., '74 13. New Haven, Conn Feb., '75 14. Dover, N. J.* May, '75 15. Cleveland, O Oct., '75

Jan 1, 1929

By C. A. Hartnagel

During- the past 10 years the annual production of petroleum in New York has averaged close to 5,000,000 bbl., the total for the period being 49,881,000 bbl. In 6 of the 10 years, the production was slightly in excess of the 5,000,000 mark. The 1944 production of 4,697,000 bbl. represents a 7 per cent decline from the previous year. Of the total 1944 output, the Allegany County district, which includes two small areas of Steuben County, contributcd 3,614,065 bbl., a decline of 5 per cent from 1943, and the contribution of Cattaraugus County, which represents the northern extension of the Bradford pool of Pennsylvania into New York was 1,082,935 bbl., a decline of more than 14 per cent. Since March 1942, the posted price of New York crude oil has remained at $3.00 per bbl. On lug. I, 1944, a Federal subsidy of 75¢ per bbl. was granted to oil producers, thus making the price actually $3.75 per bbl. Since all of the oil produced in New York comes under the designation "stripper well operations," it is entitled to the Federal subsidy. During the last few years there has been little change in the number of wells drilled annually. In the Allegany field, which accounts for three fourths of the oil produced in the state, 1240 wells, including water-intake wells, were drilled during 1944 as compared with 1223 in 1943. There was no marked increase in the number of wells drilled after granting the subsidy of 75¢ per bbl. of oil on Aug. I, the increase being but 14 wells during the last half of the year over the preceding six months. In flooding operations it is not to be expected that even a substantial increase in the price of crude oil will be reflected quickly in an increase of the number of wells drilled or in a marked increase in production of crude oil. In flooded areas, oil is obtained through a program extending over a number of years. This program involves the drilling of the water or input pressure wells, drilling of the oil wells, building up the oil flood to maximum production, and finally the watering out of the well when the amount of oil produced in proportion to the water becomes so small that pumping is no longer profitable. The various operations may extend over a period of 10 years or more, during which time the price of crude may have fluctuated greatly. Although the rate of production can be controlled to a limited extent, it is evident that a flood when once begun must be continued regardless of the price of crude. During the past seven years New York crude has had a price range from $1.68 per bbl. in 1938 to the present price of $3.75 per barrel The field pattern now in general use for wells in a flood project is the "five-spot." Under this arrangement, the lease is divided into squares with a water well at each corner and an oil well in the center. In the all-over pattern of the lease each oil well is acted upon by four water wells and each water well supplies part of the pressure to four oil wells. Spacing between the input water wells and the oil wells usually varies from zoo to 225 ft. or, on an acre basis, there is one oil well and one water well for each 2 1/2 acres. In recent years there has been a tendency to increase

Jan 1, 1945

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1940 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. TECHNICAL PUBLICATIONS in Classes A-Metal Mining, B-Milling and Concen-tration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETRO-LEUM TECHNOLOGY, which was issued quarterly in 1940 but will be issued every other month in 1941. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administration, and L-Geophysical Methods of Exploration are issued as separate pamphlets. An Institute member is entitled to one copy of any TECHNICAL PUBLICATION or CONTRIBUTION. Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute accord-ing to their registration by classes. CONTRIBUTIONS and other TECHNICAL PUBLICA-TIONS will be sent upon request. A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent a page; minimum charge, 25¢. Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1.25 domestic, $1.35 foreign countries. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum domestic, $2.50 foreign. METALS TECHNOLOGY, $7 per annum domestic, $7.80 foreign (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers). MINING TECHNOLOGY, $6 per annum domestic, $6.60 foreign (metal mining, milling and concentration, Industrial Minerals Divi-sion, and mining geology papers.) PETROLEUM TECHNOLOGY, $6 per annum domestic, $6.60 foreign. Bound volumes have been mailed to members that have requested them, and MINING and METALLURGY is mailed each month. A member is entitled to one volume a year on his membership and he may purchase for $2.50 one copy of a volume not already received; additional copies of the same volume, $5. Nonmembers may pur-chase the volumes listed, at $5 each, plus 60 cents for Canadian or foreign postage. Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 50¢ each to members; to nonmembers 506 current issue and $1 each, back issues. Subscription price to nonmembers and to members for extra copies, $3 per annum domestic, $4.00 foreign.

Jan 1, 1940

By B. K. Larkin, H. R. Bailey

A model Of heat flow in an underground combustion process is studied. This model includes convection effects and thus is more general than previous studies which considered conduction as the only mechanistn for heat transfer. Both linear (tube run) and radial (field application) geometries are considered. The effects of ignition heaters, vertical losses and finite source width are considered for the linear case. The results are in the form of equations and are presented in graphical form for a number of cases. Convection effects increase frontal temperatures about 25 per cent over those computed for conductive transfer for typical field operating conditions. This increase in temperature is a result of heat being transported toward the front by the injection gas. Even greater temperature increases are realized as the per cent oxygen in the injection gas decreases. It is well known that compression costs are of considerable importance in estimating the economic feasibility of underground combustion. By assuming an ignition temperature for the combustion fuel, predictions of limiting conditions on fuel density and injection rate necessary to sustain the combustion zone are made. For typical field conditions, at least 0.75 lb/cu ft of fuel are needed with air as the injection gas. If the injection gas is 10 per cent oxygen and 90 per cent nitrogen, this figure is 0.69 lb/cu ft. INTRODUCTION The possibility of increasing oil recovery by underground combustion has been considered for many years. Recent field tests indicate that the underground combustion process is technically feasible. The economic feasibility depends to a large extent on the amount of air which must be injected to sustain combustion. Prediction of the success of employing underground combustion in a particular reservoir must be based on existing field tests, laboratory tube runs"' and solutions of mathematical or analog models. Vogel and Krueger5 devised an electrical analog of the heat transfer problem in an underground combus-ion process. They considered the problem of heat conduction from a cylindrical source with increasing radius assuming no vertical losses. Bailey and Larkin and Ramey solved the corresponding problem including vertical losses by considering a mathematical model of the conduction process. Ref. 9, 10 and 11 also present information related to the subject study. The present paper generalizes these results to include both conduction and convection mechanisms for heat flow. A model of the conduction-convection process is described. The partial differential equations governing this model are written and solved for a number of cases of interest. The formulas are evaluated and the results are presented graphically. A CONDUCTION-CONVECTION MODEL Description of the Model A number of models are employed in this paper, each of which approximate a particular physical situation depending on the geometry, i.e., linear or radial flow, the type of vertical heat losses, the nature of the source, etc. The geometry for both the linear and radial case is shown in Fig. 1. A particular linear model is described in this section, and variations from this model are described in later sections of the paper. Consider a homogeneous, semi-infinite porous prism with lateral sides insulated as shown in Fig. 1. The left end, x = 0, is heated for a time t, with a plane heater supplying a constant heat flux and during this time; gas (nitrogen) is passed through the pores of the prism at a constant mass flux. At time t, the heater is turned off and air is injected in place of the nitrogen. This causes combustion to take place, and a uniform source of width 1 is formed which moves at a constant velocity v, to the right. The frontal velocity v, is related to the gas velocity v,, through stoichiometric considerations

By W. F. Carew, H. D. Kessler, F. A. Crossley

AS part of a program on phase relationships and transformation processes of titanium alloy systems, the titanium-rich corner of the Ti-Mo-V system has been investigated. This region was surveyed primarily to supply information toward the development of a creep resistant, weldable alloy, with a minimum alloy content, for use in the 425° to 550 °C range. Specifically, the investigation was directed toward the development of a stable ß alloy with less total alloying additions than is found in the Ti-30 pet Mo alloy. A secondary objective was the development of a creep resistant, weldable a-ß alloy for application around 300°C. Molybdenum was selected as primary additive to titanium on the basis of an investigation1 which showed that the Ti-30 pet Mo alloy had promising elevated temperature tensile properties. Furthermore, aging studies1 showed no tendency for this

Jan 1, 1957

By Daryl R. Tweeton, William H. Engelmann, Orin M. Peterson, Jon K. Ahlness, Gregory R. Anderson

The Bureau of Mines measured the geochemical changes as H2SO4 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen,HC03, U. V, Na, K, Ca, Mg,S04, CI, Mo, Mn, Fe, AI, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

By A. T. Aldred, K. M. Myles

The vapor pressure of chromium over solid V-Cr alloys has been measured by the torsion-effusion method in the temperature range 1450" to 1650°K. The chemical activities as well as the free energies, entropies, and enthalpies of formation of the alloys have hem computed from the vapor-pressure data. The activities of both chromium and vanadium exhibit fairly small negative deviations from Raoult's law over the entire composition range. The values of the excess entropies and the enthalpies of formation found at 1550°K are considered in terms of the changes in the clzaracteristic properties of vanadium and chromium that occur upon alloying. RECENT interest in the theory and properties of transition-metal alloys has shown the need for relevant thermodynamic data. The present investigation of the V-Cr system was undertaken as part of a more general study of thermodynamic properties of transition-metal alloys. The system was chosen because of the reported complete solid solubility of the components at all temperatures1 and because the difference in magnitude of the vapor pressures of vanadium and chromium allowed a simple effusion technique to be used. The torsion-effusion method was employed to minimize compositional changes in the alloys during the experiments. EXPERIMENTAL Equipment. The torsion-effusion apparatus, shown diagrammatic ally in Fig. 1, consists of a torsion system suspended inside a vertical vacuum chamber whose lower end is surrounded by a high-temperature vacuum furnace. An auxiliary optical lever and screen are used to determine the angle of rotation of the effusion cell. The torsion fiber is an annealed, high-purity, tungsten wire usually between 0.003 and 0.007 cm in diameter and about 43 cm long. The wire supports a concave mirror and a rigid tantalum connector tube. The effusion cell is fastened to the lower end of the connector tube by a dovetailed yoke and har- ness arrangement. The cells, which are 1.27 cm in diameter and 4.4 cm long, were made by electron-beam welding tantalum endcaps onto a 0.025-cm-wall tantalum tube. The two orifices, formed by drilling, have similar areas ranging from 0.011 to 0.031 sq cm. The noninductive sheath-type furnace consists of a single-phase tantalum heating element 6.35 cm in diameter, 15 cm high, and 0.013 cm thick; the element is completely surrounded by radiation shields in an evacuated chamber. The power system includes a 17-kva self-saturating saturable core reactor with an integral magnetic amplifier and a water-cooled, 15-kva, step-down power transformer with a multitap secondary. Temperatures are controlled to within ±1/2o at 1600°K by means of a unit that includes a reference voltage source, a dc electronic null detector, a current-adjusting proportional band relay, and the self - saturating reactor. At 1650°K the temperature variation within the cell, vertically and horizontally, is 3/4oK. Unwanted motions of the torsion system are damped by the movement of an aluminum vane, which is mounted on the connector tube, between the poles of an electromagnet. When not in use the magnet is withdrawn and rotated 90 deg to prevent its interaction with the rotation of the system. Measurements. The vapor pressure, p, is re-

Jan 1, 1964

By R. Janes, F. Everard

Pilot plant studies have been conducted on a variety of iron ores of differing composition and grain size to test their amenability to dry autogeneous grinding and dry magnetic concentration. A general description of the pilot plant and its equipment is given with particular reference to the Aerofall mill and the dry magnetic separators developed by the Ontario Research Foundation. Test results are reviewed in detail with emphasis on power consumption, mill speed, the use of ball charges, types of ores, moisture content, separator speeds, and design. In 1957 the Ontario Research Foundation installed a pilot plant (Fig. 1) for the study of dry autogenous grinding and dry magnetic concentration of iron ores. A 61/2-ft Aerofall mill was installed as the dry autogenous crushing and grinding medium. The Cavanagh fast drum and the Double Helix, two dry magnetic separators developed at Ontario Research Foundation, were also installed. Iron ore samples of 10 to 150 tons have been investigated. These ores varied widely in mineralogy and grain size. Taconite (-325 mesh), fine-grained magnetite (200 to 325 mesh), and medium-grained magnetites (65 to 150 mesh) have been treated with varying degrees of success. Lately, considerable research has also been conducted on the metamorphosed magnetite-hematite complexes of the Labrador Trough. Operational and metallurgical data have been compiled from these tests. The effects of ore type, air flow, mill speed, and ball charge on mill operation are discussed. Metallurgical data are also presented to illustrate the operation of the dry magnetic separators. PILOT PLANT DESCRIPTION Fig. 2 depicts the normal flowsheet used. Minus 6-in. ore from a vibrating feeder is fed to the 6%-ft Aerofall mill powered by a 50-hp 550-v induction motor. The main blower, a 25-hp 550-v fan rated at 7000 cfm, draws air through the mill. Finely ground ore is conveyed by the air stream to a horizontal classifier, where expansion and a change in direction cause the +I50 mesh fraction to fall onto a vibrating

Jan 1, 1962

E. S. BARDWELL,* Great Falls, Mont. (written discussion ?).-There are several points in. connection with the manufacture of ferromanganese in the electric furnace which it seems to me. might prove of interest in this connection. Recent observation of a, number of electric furnaces varying considerably in size and transformer capacity, and all working under the same conditions, shows the small furnaces to be much more efficient in operation than the large furnaces. The furnaces examined were all of the same type. The crucibles consisted of tanks varying in size from 71-z by 15 ft. by 4 ft. deep, to 12 by 20 ft. by 9 ft. deep, with linings formed of carbon electrode butts. The smaller furnaces had transformer capacity rated at 1500 k.v.a.; the largest furnace had a transformer rated at 3000 k.v.a. All of the furnaces were operated on three-phase, 60-cycle current, the three electrodes being in a straight line. The voltages varied from 65 volts in the smaller to 100 volts in the larger furnaces. The charges consisted of manganese ore, coal, iron turnings, and limestone in proper proportions. The small furnaces, operating at low voltage, were making good recoveries. The slag loss was low and the volatilization loss almost nil. The larger furnaces, operating at higher voltages, showed increased loss of manganese in the slag and greatly increased volatilization loss when working on the same charges as the smaller furnaces, or on charges similarly calculated. The exact reasons for this state of affairs are difficult to state; a number of factors probably contribute to the results obtained in the large furnaces. First as to the effect of the higher voltage on manganese content of the slags. Increasing the voltage of the furnaces apparently tends to promote irregular working. The current takes the path of least resistance; this means superheating in certain areas in the crucible and insufficiently high temperatures in adjoining areas. The partially reduced manganese in the cooler areas passes into the slag and escapes further reduction.

Jan 11, 1918

By Edward Norton

THE -salt deposits of the Mississippi Embayment region present a problem of origin so genetically related to the larger problem of the stratigraphy and structure of the region that a discussion of the one necessarily involves or assumes an understanding of the other. For this reason, I shall summarize briefly our knowledge of this region, emphasizing the facts related to the subject of this paper. In so doing I shall make liberal use of the reports of the National and State surveys. Geographically that section of the United States known as the Mississippi Embayment region represents a great V-shaped area, extending from near Cairo, Ill., to the Gulf of Mexico, and including Louisiana, eastern Texas, all that part of Arkansas bordering the Ouachita and Ozark mountains, western Tennessee, Mississippi, and a part of Alabama. This great section Professor Harris has described as structurally a pitching trough, its medial line being well represented by the Mississippi River. Outcropping along the border of this area are the Cretaceous and Tertiary formations, unconformably laid down on the hard Paleozoic rock sheets that show more or less plication, deformation, and faulting, depending upon their proximity to the nearby major uplifts. East and west of the Mississippi River the Cretaceous and Tertiary beds dip river- and coastward at angles greater than the slope of the land. "Waters entering along the outcropping edges of the Tertiaries and Cretaceous and following bedding planes southward are soon thousands of feet beneath the surface." As the sedimentation of the region progressed, faulting and slips occurred along planes of pre-Cretaceous weakness. Whether these movements were genetically related to the loading of this V-shaped area, as Professor Harris seems to think, is a question still to be settled. The accompanying map, Fig. 1, was taken from Bulletin No. 7 of the Louisiana Geological Survey. It shows the regional distribution of the salines, as well as an alignment of the domes, which has been assumed to indicate faulting.

Jan 1, 1915

By W. O. Philbrook, K. Natesan

The oxidation kinetics of spherical pellets of zinc sulfide made from Santander concentrates were studied using a thermogravimetric technique. The experiments covered a temperature range-. of 740" to 102O°C, 0-N mixtures varying from 20 to LOO pct O2, and pellet diameters between 0.4 and 1.6 cm. Mathematical models were formulated to Predict the reaction rate on the assumption that a single transport or interface reaction step was rate -controlling. Analysis of the data indicated that the process of oxidation was predominantly controlled by transport through the zinc oxide reaction-Product layer. ROASTING processes, which are reactions between solids and gases, are very important because they are employed in the production of a number of basic metals. These processes are highly complicated, and one needs to consider the transport phenomena of heat and mass between the solids and gases in addition to the kinetics of various chemical reactions involved. Because of such complications there is a lack of knowledge concerning the rate-limiting factors, which may strongly depend on temperature, particle size, gas composition, and solid structure. The oxidation of zinc sulfide, which is of commercial importance in zinc production, falls into this class of reactions. The major goal of this work was to elucidate the roles played by different process variables, such as reaction temperature, gas composition, pellet size, and pellet porosity, on the kinetics of oxidation of single pellets of zinc sulfide. Roasting of zinc sulfide single particles has been a subject of both experimental and theoretical investigations.&apos;-&apos; The reaction is exothermic and may be considered to be irreversible. Such a reaction has been found to proceed in a topochemical manner. In other words, as the reaction proceeds, a progressively thicker outer shell of zinc oxide is formed, while the inner core of unreacted sulfide decreases. It has been found experimentally, both in the present work and in the previous investigations,1-9 that the particle retains its original dimensions and the process requires transport of gaseous oxygen across the porous product layer for continued reaction. The reaction may be represented by ZnS(s) + 3/2 O2(g) = ZnO(s) + SO2(g) [1] The solid product considered here is only zinc oxide, since the diffraction patterns of zinc sulfide pellets oxidized partially at &apos;798" and 960°C showed K. NATESAN, Junior Member AIME, formerly St. Joseph Lead Fellow, Department of Metallurgy and Materials Science, Carnegie-Mellon University, Pittsburgh, Pa., is now at Argonne National Laboratory, Argonne, Ill. W. 0. PHILBROOK, Member AIME, is Professor of Metallurgy and Materials Science, Carnegie-Mellon University. This paper is based on a them submitted by K. NATESAN in partial fulfillment of the requirements for the Ph.D. degree in Metallurgy and Materials Science at Carnegie-Mellon University. Manuscript submitted December 2, 1968. EMD lines corresponding to original zinc sulfide and the newly formed zinc oxide. OXIDATION MODEL The generalized model for gaseous oxidation of zinc sulfide is illustrated in Fig. 1. This depicts a partially oxidized sphere of zinc sulfide in a gas stream surrounded by a laminar film of gas. The spherical sample of zinc sulfide of unchanging external radius r0 is suspended in a flowing gas stream of total pressure PT and composition specified by the partial pressures of the individual components. Partial pressures of the gaseous species in the bulk gas phase, at the exterior surface of the pellet, at the ZnS/ZnO interface, and at equilibrium for Reaction [I] are identified by the superscripts b, o, i, and eq, respectively. The overall reaction involves the following ~te~s:&apos;~&apos;~&apos; Step 1. Transfer of reactant gas (oxygen) from the bulk gas stream across the gas boundary layer to the exterior surface of the pellet and the reverse transfer of the product gas (sulfur dioxide). Step 2. Diffusion and bulk flow of oxygen from the pellet surface through the product shell (ZnO) onto the ZnS/ZnO interface and the reverse transfer of sulfur dioxide. Step 3. Chemical reaction at the interface, which results in consumption of oxygen gas and generation of sulfur dioxide gas and heat; at the same time the _________ PARTICLE SURFACE / x^^^^n^X / MOVING INTERFACE core-----/ sJSNxy " /T^T^02 \ V\V$\ ^NWX/ "*/— GAS BOUNDARY x. \\ZnO SHELLV/ / \^ . / &apos; ^ BULK GAS --------N_______ _____,------p£ w \ P« / (f> \ / a \ <i) / <----------------- _(o) ^^--------------(b) °- pso, pso2 ro ri 0 ri ro RADIAL POSITION Fig. 1—Generalized model for oxidation of a sphere of zinc sulfide.

Jan 1, 1970

By F. P. Haver, M. M. Wong

When a mixture of chalcopyrite concentrate and lime is heated in air, the following reaction takes place: 2CuFeS2 + 4Ca (OH)2 + 8 ½ 02 ; 2Cu0 + Fe203 + 4CaS04 + 4H20. Ca (OH)2 is the only common reagent that will adequately control SO2 evolution in roasting. Other additives tried, including CaO, CaCO3, Na2CO3, NaOH, MgO, Mg (OH)2, and MgCO3, were not effective. All reacted with sulfur, but not to the extent that will be required to meet the new control regulations for sulfur oxide emissions. For example: when the concentrate was heated with the theoretical amount of limestone (CaCO3), about 55% of the sulfur was retained in the calcine; whereas use of the stoichiometric amount of Ca (OH), converted approximately 99% of the sulfur to CaSO1. In most of the experiments, Ca(OH)2 was formed by adding CaO to concentrates containing enough water to simulate filter cake from flotation circuit. This eliminated the need for drying the concentrate and utilized the heat of hydration of CaO.

Jan 6, 1972

Organization Place 1917 National Association of Stationary Engineers .... Evansville, Ind. Sept. 10-15 National Safety Council New York City. Sept. 10-15 National Exposition of Safety and Sanitation.... New York City. Sept. 10-15 American Iron, Steel & Electrical Engineers Philadelphia, Pa. Sept. 10-14 American Association of Port Authorities Cleveland, Ohio. Sept. 11-14 American Institute of Metals Boston, Mass. - Sept. 24-29 American Foundrymen&apos;s Association Boston, Mass. Sept. 24-29 Chemical Industries, Third National Exhibition.. New York City. Sept. 24-29 American Electrochemical Society Pittsburgh, Pa. Oct. 3-6

Jan 9, 1917

By Frank L. Nason

RECENT explorations with a diamond-drill, originated and conducted by Mr. J. A. Van Mater, Superintendent of the Lehigh Zinc and Iron Company, have revealed some very important geological facts, which, it is believed, will be of special practical interest to mining engineers. During these explorations the writer was frequently called in consultation, and hence the facts here recorded are almost entirely the results of personal observation. The franklinite-deposit upon which the explorations were conducted has a long continuous outcrop. Figs. 1, 2 and 3 give a map and sections. Beginning at the extreme southern point,

Jan 1, 1895

By N. J. Grant, I. S. Servi, A. Chaudhuri

IN a recent paper by Servi and Grant,&apos; it was illustrated that the slip band spacing and stress based on creep test data were related by the equation: d =1/ where d is the spacing in millimeters and v is the stress in psi, based on a more complete equation proposed by Orowan. It was shown further,&apos; that for a. given grain size, the slip band spacing became larger with decreasing stress (and was independent of temperature), until such time that the slip band spacing becomes greater than about one-half the grain diam- eter. When this occurred, the mechanism of deformation in creep of 2s aluminum at high temperature changed from slip to grain boundary deformation (sliding). Additional metallographic evidence is now available which confirms this in a most interesting fashion.

Jan 1, 1954

Electrical requirements in surface mining can be divided into three categories: main substation, plant power, and pit distribution. A main substation may vary from a 500-kva transformer supplying 480-v power to motor-driven pumps and conveyors, to a 50,000-kva substation serving a large beneficiation plant or a large strip mining operation. Regard- less of size, it should be designed with the realization that a failure of the main substation will totally shut down the operation. Location of a main substation usually is a compromise between expense of running the incoming high-voltage transmission lines and the voltage drop of long secondary runs. Based on a geological survey for immediate and future areas of excavation, the main substation should be located as near to the center of load as possible.

Jan 10, 1967

By L. L. Melton, D. L. Lord, B. W. Hulsey

A mathematical model d1.20p/4L = A(8v)8 derived from the Blasius equation is proposed to be applicable to turbulent flow through straight cylindrical pipe for time-independent fluids which produce a diameter family of straight parallel lines on a log (dp/4L) vs log (8v/d) plot or stress-flow diagram. Such a correlation should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable frictional pressure reductions. The Newtonian diameter exponent value 1.20 is shown to be empirically valid for turbulent non-Newtonian flow by application of numerical analysis methods. Multiple regression analysis is applied to a logarithmic linearization of the proposed model. An improved data fit results from further linearization achieved by taking linear terms from a generalized Taylor&apos;s series expansion about the multiple regression coefficients. Extensive experimental data obtained in five pipe diameters with water, sodium carboxymethyl-celIulose solutions, guar gum solutions, bentonite clay suspensions and calcium carbonate slurries are presented. Except for calcium carbonate slurries, which were investigated rather than time-dependent cement slurries, the fluids studied contain drilling or fracturing fluid additives. The behavior exhibited by these fluids is considered typical of most fluids encountered in drilling, cementing and fracturing operations. INTRODUCTION Considerable difficulties have been encountered in predicting turbulent flow pressure drops produced by non-Newtonian fluids flowing through straight cylindrical pipe. Correlations previously presented require extensive experimental data which represent several pipe diameters and a wide flow rate range to estimate the necessary scale-up parameters.l-7 One must implement either elaborate experimental apparatus or spend considerable time and effort to gather these data. Presented here is a correlation method which should minimize the experimental effort and data analysis normally required by utilizing flow data taken with only one pipe diameter. Turbulent flow data (up-stream and down-stream pressure and volumetric flow rates) were collected for five pipe diameters through operation of a small pipeline system having an electronic data acquisition and digitizing system. A mathematical model derived from the Blasius equation was utilized to describe the functional relationship between pressure drop and the two independent variables, diameter and average flow velocity. A correlation, which should produce a valid single-pipe scale-up, resulted from a computer-implemented statistical and numerical data analysis for several time-independent non-Newtonian fluids.

By E. A. Holbrook

IT may be taken for granted that a mine official knows his duties, as outlined by the bituminous mining laws of the State, he knows how coal should be mined and transported, and he has judgment on any possibly unsafe condition in his mine. Certainly, if he is weak on any of these points, there are definite ways in which he can acquire the needed knowledge. If with this knowledge the mine official has the necessary practical experience to bring self-confidence, he stands before the world as a man who knows his job. There is, however, another side to his work, one not found in hooks, a side even that may not be learned at the face even though one spends a lifetime there. The actual duties a mine official knows and performs are the tangible and definite things about his work. There are other things which may be termed intangible, because they are hard to pin down and see, and. which appear to be of equal importance in successfully handling a job and which in time determine the very success of the company itself.

Jan 1, 1930