Search Documents

By Charles Maier

IT has long been supposed that when crystalline materials are com-minuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led to the author's attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1. The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chem-ical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the cor-rected heat of solution was less for fine material than for coarse. Con-tinuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author's work by

Jan 1, 1936

By Akinobu Kasami, Keiji Maeda, Makoto Naito, Masaharu Toyama

Gap electroluminescent diodes have been prepared by the vapor phase diffusion of zinc into n-Gap crystals which were grown from a gallium solution (10 wt pct Gap) doped with tellurium and Ga203. A marked improvement in the efficiency of the red electrolumines -cence has been achieved by heat treatment after diffusion. External quantum efficiencies of diodes annealed under optimum conditions are 0.2 to 0.6 pct at room temperature, or about 200 times higher than the efficiencies of diodes quenched after diffusion. The optimum dopant concentrations in the gallium melt from which the crystals were grown are 3to6 x at. pct Te and 4 to 8 x 10-2 mol pct Ga203. The efficient diodes are characterized by linearly graded junctions with an i-layer 0.1 to 0.2u thick. Annealing increases the emission intensity by a factor of 20 to 50 and decreases the current density to 1/3 to 1/8 that of quenched diodes at a given bias. The decrease in current is attributed to an annihilation of deep recombination centers in the depletion layer. The increase in emission intensity is interpreted in terms of an increase in lifetime of minority carriers and an increase in the relative intensity of red-to-infrared emission. The dependence of these quantities on the tellurium and oxygen doping levels is also discussed. A number of studies have been made of the red light emission from for ward-biased Gap diodes.' At room temperature this emission band is centered at 7OOO? with a spectral width of nearly 1000?. Low-tempera-ture photoluminescence indicates that this emission is due to either the radiative annihilation of an exciton bound to a pair of zinc and oxygen atoms substituting on nearest neighbor lattice sites2,3 or the radiative recombination of an electron bound to this Zn-O pair with a hole bound to an isolated zinc shallow acceptor.3 An emission band is also observed with a spectral peak at 9800?. This infrared emission has been shown to be due to the recombination of an electron trapped at an isolated oxygen deep donor with a hole trapped at an isolated zinc acceptor.4 The red emission from Gap diodes is fairly efficient at room temperature because the nearest neighbor Zn-0 pair forms a deep electron trap at 0.3 to 0.4 ev below the edge of the conduction band.2'4 In diodes grown by liquid epitaxy an external quantum efficiency of 2.1 x 10-2 (photon/electron) has been attained by heat treatment at relatively low temperatures.5 This heat treatment was found to increase the efficiency by a factor of 3 to 6. However, no detailed studies have-been reported on the effects of heat treatment. We can only cite Onton and Lorenz's work6 on the change ; in the relative intensity of red-to-infrared emission. Heat treatment has also been tried on junctions built in during growth, but contrary to expectations the efficiency decreased. In-diffusion is a simple and controllable method of fabricating p-n junctions. For Gap, zinc is generally used to form a p-type layer on n-type crystals. The emission efficiencies of in-diffused diodes are, however, extremely low in comparison with liquid epitaxial diodes.' Although efficiencies as high as 2 x 1O-3 have been reported, values from 10-6 to 10-4 are generally obtained by typical diffusion techniques. Out-diffused diodes are known to be a little more efficient than in-diffused diodes. Nevertheless, the quantum efficiency is at most 7 x 10- 3 and ordinarily of the order of 10-4.8 NO results have been reported on heat treatment of either in-diffused or out-diffused diodes. This paper reports a marked improvement in the efficiency of the red emission observed for in-dif-fused diodes as a result of heat treatment after diffusion. The method described reproducibly yields diodes with external quantum efficiencies of 2 to 6 x 10-3. The observed dependence of efficiency on annealing time and on doping level will be discussed in terms of the lifetime of minority carriers and the formation of Zn-O complex pairs. EXPERIMENTAL A) Diode Fabrication. The n-Gap crystals used in this study were grown from a saturated gallium solution by a slow cooling method.8 The Gap content in the gallium melt was fixed to 10 wt pct corresponding to a growth temperature of about 1100 Tellurium was chosen as the n-type dopant and added to the melt in concentrations ranging from 0.001 to 0.06 at. pct. Oxygen was added in the form of Ga2O3, whose concentration was varied from 0.004 to 0.2 mol pct. The resulting crystals were platelets with well-developed (111) surfaces. Typical electrical properties were Hall mobilities of 130 to 30 sq cm per v-sec and carrier concentrations of 1016 to 10" cm-3 at room temperature. Diodes prepared from crystals with relatively low doping levels, in which u = 130 to 100 sq cm per v-sec and n = 0.6 to 6 x 1017 Cm-3, were examined in detail. The p-n junctions were produced in these n-Gap crystals by the diffusion of zinc from the vapor phase by the following procedure. The platelets were carefully lapped on both sides to a thickness of 150 to 200 u while maintaining the (111) orientation. After being etched in hot aqua regia, the crystals together with the zinc were sealed in an evacuated 12 mm ID quartz ampoule 20 cm long. The crystals and the zinc were then separated from each other at opposite ends

Jan 1, 1970

By L. D. Rickets

The principles on which an art is founded are usually few and necessarily basic in nature, but he who wishes to achieve the power to select his aides and give success to important undertakings that may be entrusted to him in the future must ordinarily undergo years of drudgery in order to gain the experience that will enable him to distinguish such fundamentals through the haze of reenforcing detail that clothes and tends to disguise them. This especially applies to those who would dream dreams that may come partly true. Professor Henry B. Cornwall of Princeton was a graduate of Freiberg with mining experience in Mexico. He was my friend and mentor during my college life. In 1883 I finished my postgraduate course and had two offers of work to consider. His advice is very clear in my mind today. It was essentially as follows: I know something of the mines of Mexico and have crossed through the mountains of the West. The West possesses a vast area of mountain and valley. California has long had its gold mines, the Comstock and Gilpin County followed and now comes the discovery of Leadville. I believe the West, will become a great mining country. You can choose now to teach here or go to the mountains. Were I in your place I would go West and identify myself with mining.

Jan 1, 1932

NORTH AMERICA ALASKA Anchorage.-Neitzert, G. H. Strandberg, H. Candle.-Robbins, J. S. College.-Barber, R. J. Burns, W. T. Coats, R. R. Fox. E. F. Joesting, H. R. McAnerney, J. M. Colorado Station.-Beyer, A. Stanford, J. V. Douglas.-Cahill, W. E. Carlson, L. Fairbanks.-Crawford, J. D. Earling, R. B. Fowler, D. A. Greves, J. H. Henton, H. M. Herbert, C. F. Hopkins, J. E. Kreitlow, E. J. MacDonald, D., III Mathews, T. C. McCarty, W. J. McNair, W. H. Metcalfe, J. B. Mikami, H. M. Mize, R. J. CANADA ALBERTA Calgary.-Johnson, R. V. Link, T. A. Marple, L. E. Slipper, S. E. Thorne, B. L. Thorne, H. L. Vissac. G. A. Edmonton.-Ball, -M. W. Lilge, E. O. Pitcher, N. C. Nordegg.-Shanks, J. BRITISH COLUMBIA Allenby.-Lindsay, W. R. Bralorne.-Almstrom, A. A. Bosustow, R. Currie, J. M. Gibson, S. Schmitt, D. E. G. Wilson, G. H. Bridge River.¬Botterill, T. C. Crane, G. A.

Jan 1, 1939

Executive Committee, Board of Directors Grover J Holt, Chairman, C E Reistle, Jr , Vice-Chairman, A W Thornton, A B Kinzel, J L Gillson Finance Committee, Board of Directors Andrew Fletcher, Chairman, R B Caples, Gail F Moulton Investments Erle Daveler, '60, Chairman, Henry Krumb, '59, John Warren, '60, C R Dod¬son, ex off as Treasurer, Andrew Fletcher, ex off as Chairman, Finance Committee Endowment Andrew Fletcher, Chairman, N G Alford, E V Daveler, W J Coulter, J V N Dorr, R B Gilmore, J B Haffner, 0 H Johnson, D H McLaughlin, J R McMillan, L F Reinartz, C E Weed, Wilfred Sykes, J R Suman Honorary Memberships L F Reinartz, Chairman, C E Reistle, Jr , H DeWitt Smith, ex off as Past Presidents of AIMS, Grover J Holt, ex off as President AIMS, P D Merica, '59, Henry Krumb, '58, M L Haider, '60, D H McLaughlin, '61

Jan 1, 1957

Jan 1, 1930

By L. A. Dale, D. A. Dahlstrom

Closed-water circuits are justified today from two standpoints: economical operation and prevention of stream pollution. In today's modern preparation plant, it has been found very desirable to have the plant circulating water maintained at a relatively low solids concentration of around 3%. In so doing, bene-ficiation equipment can operate at a much higher efficiency. However, makeup water requirements would become excessive if the fines were to be removed from the preparation plant by bleeding a 3% solids concentration to a tailings pond. With the ever increasing percentage of —200 mesh coal, clay and slimes in the raw coal, coupled with the creation of these fines within the preparation plant, the need for water conservation for economy reasons becomes even more important. Because of stream pollution laws, tailings ponds have become very costly to operate and maintain, resulting in the necessity of employing an in-plant method of water recovery. Accordingly, the primary system employed in water recovery in the coal preparation plant today consists of a solids concentration device to thicken refuse solids while at the same time producing a sufficiently clarified effluent that can go back to the preparation plant for water reuse. The thickened product is then normally passed to a dewatering device that will produce a handleable solid that can be disposed of

Jan 1, 1965

By Frank H. Reed, P. W. Henline, Harold W. Jackman

A SUMMARY of the consumption of coal in 1945 shows that the coke industry accounted for 17 pct of the total coal used. No substitute for coke and the blast furnace in the reduction of iron ore has gained sufficient prominence so far to be given serious consideration. However, while the same slot-type ovens are being built and used now as were in use a few years ago, the problem of obtaining suitable coking coals, both high- and low-volatile, has forced many operators to revamp coal-blending facilities. Until the beginning of World War II, high-temperature coke plants were able to secure the required high-volatile and low-volatile coals from two or three seams and from three or four mines. Thus, many of our coke oven plants were able to operate with storage bins for two coals only. The variance in raw materials was not great, and uniformity of blend was a relatively simple problem. Since the beginning of World War II, many and important changes have taken place. Demand for all coals increased greatly. Production, though kept as near maximum capacity as possible, could not meet the demands for coal generally, and particularly for the various kinds of coal which have proved to be satisfactory for specialized uses; coals were allocated as nearly as possible in the order of greatest need; storage piling was reduced to the minimum necessary to keep plants in operation; uniformity of quality could not be maintained, and with this last, uniformity of composition of blends for coking could not be maintained. Whereas before the war producers of metallurgical coke could fill their needs from three or four mines, by the end of the war it was not unusual to find shipments to a single coke oven plant coming from as many as 30 different mines, in a single month. Since many of the mines producing both high- and low-volatile coal for high-grade metallurgical coke are rapidly nearing depletion, the problem of seeking new sources and of blending a number of coals in each plant for the production of high-temperature coke is facing practically every producer in the United States at the present time, and is one which will probably continue for many years to come. Midwestern by-product coke ovens in the Chicago and St. Louis areas use annually from 12 to 15 million tons of bituminous coals which are transported 500 to 700 miles from the Appalachian coal fields of Pennsylvania, West Virginia, and eastern Kentucky. Approximately two-thirds of this coal is high-volatile bituminous. The critical transportation problem confronting the nation in 1943, and the growing scarcity of the best Appalachian coking coals, prompted the Illinois Geological Survey to propose a research program in which would be studied the coking properties of blends of low-sulphur, high-volatile Illinois coal with the high- and low-volatile coals from the eastern fields. Such blends containing Illinois coal, if substituted for the all-eastern blends normally coked,

Jan 1, 1948

ORE at the Jeffrey mine of Canadian John Mansville at Asbestos, Que., is hoisted by two 12 1/2 - ton capacity aluminum skips, counterbalanced. When the loaded skip reaches the surface it empties, via its sliding door, into a bin. Simultaneously, the skip tender, who operates at the 940 level, loads ore into the alternate skip from a 12 ½ -ton measuring pocket. This done, he sets the skips in motion. Problem: When moisture content of the asbestos ore is high, the ore, unknown to the skip tender, some- times sticks in the dumping skip, preventing complete discharge. Moreover, the sliding skip doors sometimes jam and stay open after the ore is discharged. If a skip in this condition is lowered, the result is either an overflow of ore, or the ore discharges through the open skip door, down the shaft. Spilled ore must then be mucked out of the spill pocket and hoisted in 2-ton cars. Cost is high, time is lost, and the shaft is sometimes damaged. Solution: A television apparatus was installed so that the skip tender might quickly spot improper door operation or hang-ups at the dumping station.

Jan 8, 1958

By A. S. Nowick, E. S. Machlin

ONE of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.1 During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time required for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error.2~3 This method of showing stress-rupture data has been adopted by many investigators and the KACA.4 By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, 100, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time for rupture on stress, temperature, com- position, and structure. In order to obtain this information, an investigation was made at the KACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given com- position and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efficiency and power output of gas turbines used in aircraft propulsion can be increased. THEORY The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 eveloped by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate- process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process.'' For example, in a chemical reaction the unit process is

Jan 1, 1947

By Charles E. Reed

With the increasing importance of clay in drilling operations which demand more precise and exacting control over its behavior, there has come the realization that most of our present methods of control over many of its important properties still represent more of an art than a science. Such a situation with respect to a material of such industrial significance is unfortunate, and naturally many investigations have been conducted to improve our knowledge. In general, these investigations have revealed the complex nature of clay behavior and while sometimes they may not have seemed to contribute directly to a solution of the field operator's problems they have been of inestimable importance in bringing to light the broad fundamental scientific principles upon which must be based any effective working theory correlating the known facts of clay behavior and predicting profitable new lines of attack for its improvement. Major Facts Concerning Behavior of Clays In the study of clays, as in that of most other colloidal materials, it has been impossible to make progress by the study of isolated facts. On the other hand, analysis of large groups of facts, many of which seem at first completely unrelated, can lead to a deeper insight into the structure of clays and the mechanism of their behavior. It will be well to list the major facts on which the analysis here presented is based, starting with those that have emerged repeatedly from past investigations and which thereby constitute an impregnable foundation upon which must rest any comprehensive theory of clay behavior: 1. Clays consist of hydrated aluminosilicates of extremely fine and variable particle size. 2. Suspended in water, clays exhibit variable degrees of swelling, depending upon their origin and upon the chemical and colloidal nature of any other substances present. The magnitude of the swelling is a direct indication of the extent to which the clay has become dispersed.

Jan 1, 1938

By W. L. Prehn, Adele Chambers, R. L. Slobod

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

By R. L. Slobod, W. L. Prehn, Adele Chambers

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

By J. S. Kasper, R. M. Waterstrat

IN view of the recent findings of a pronounced ordering of atoms in s phase alloys containing elements of the first long row of the periodic table (and including molybdenum),l it is of interest to resolve the question of ordering for s phases containing second and third-row elements. Examples of the latter have been provided recently by Greenfield and Beck2 and two of them, Re-Cr and Ru-Cr, would appear to be favorable for a study of ordering by X-ray diffraction methods because of the considerable differences in the scattering factors concerned. In addition, s phase is found to occur in the Os-Cr system, where the difference in scattering factors is even larger. Accordingly, X-ray powder intensities have been measured in an attempt to learn the nature of the ordering, if any, in these three v alloys. Since there is no reported work on intermediate phases in the Os-Cr system, an exploratory investigation was made in this system, and it was found that, in addition to the s phase, the phase with the A-15 or ß-W structure also occurs. Specimen Preparation—The alloys were prepared by compressing mixed powders of —200 mesh size and sintering in an atmosphere of pure dry hydrogen. All alloys were rapidly cooled from the annealing temperature to room temperature in a stream of cold dry hydrogen in a water-cooled chamber. Table I lists the sources and purities of the starting materials, as well as the details of processing for each of the alloys investigated. Intermediate Phases in the Os-Cr System—In the absence of information on intermediate phases in the Os-Cr system, it was suspected that this system would resemble that of Ru-Cr, where a s phase, RuCr2,2 and a phase with the A-15 structure, RuCr3,3,4 have been identified. Both these phases were found in the Os-Cr system and at compositions

Jan 1, 1958

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 875°F. The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of the durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth's crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica ( SiO, ) and silicates can be melted to form glasses. Alumina (A1,0,), present in a mineral com- pound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus, sand, which is generally almost pure SiO,, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide per- forms a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some non- minerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1975

By Frederick Jr. Prime

THE first catalogue of Geological Reports of the United States was prepared by Prof. O. C. Marsh, and published in the American Journal of Science and Arts for 1867, vol. xliii, second series. Since then the list has more than doubled, and it was thought that the publication of a new catalogue, brought down to date, would be useful to many of the members of the Institute of Mining Engineers. The compiler will be most thankful to have any omissions or inaccuracies in the list sent to him, to be published as a supplement in the next volume of the Transactions. Especially to have the correct title, number of pages, plates, and maps of any volume on the list to which an * is prefixed, as he has been unable to personally consult such works. A preliminary list was issued last February, which has been almost doubled by the kindness of many friends. The writer desires more especially to express the obligations he is under to the following gentlemen The Chief of Engineers, U. S. A.; Principal Dawson, Mr. G. M. Dawson, Drs. B. J. Harrington and T. Sterry Hunt, of Montreal; Mr. H. Engelmann, of La Salle, Ill.; Dr. F. V. Hayden and Prof. J. W. Powell, U. S. Department of the Interior ; Prof. E. W. Hilgard, University of California; Prof. Henry Y. Hind, Windsor, N. S.; Prof. C. H. Hitchcock, of Dartmouth College; Mr. Henry A. Holmes, State Librarian, Albany; Maj. Jed. Hotchkiss, Staunton, Va. ; Prof. W. C. Kerr, Raleigh, N. C.; Dr. J. S. Newberry, of Columbia College ; Prof. W. H. Pettee, of the University of Michigan ; Dr. Samuel H. Scudder, Prof. N. S. Shaler, and Prof. J. D. Whitney, of Harvard College ; Mr. Sanderson Smith and Prof. J. J. Stevenson, of New York ; Mr. Addison Van Name, of Yale College, and Lieut. Geo. M. Wheeler, U. S. Engineers. PHILADELPHIA, 907 Walnut Street, October 1st, 1879.

Jan 1, 1879

By George W. Sears

In preparing this symposium, our ambition was to elicit authoritative expression of opinion concerning important selected phases of the industry from men active in it. Responses to requests for contributions were gratifying, especially so in view of the short time available. The generous and cooperative spirit of the industry as a whole is amply evident. Responses were received from the following, who are therefore the true authors of the paper: W. G. Adamson, General Manager of the pershin; Quicksilver Co., Lovelock, Nev.; Dudley Baird, Vice President, Pacific Foundry Co., San Francisco; Walter W. Bradley, State Mineralogist of California; W. D. Burcham, General Manager of the Brewster Quicksilver Consolidated, Terlingua, Tex.; William Forstner, San Francisco; H. W. Gould, of H. W. Gould & Co., San Francisco; Marcus Hulings, General Manager of the Chisos Mining Co., Terlingua, Tex.; Frank J. Katz, Chief Engineer, Division Mineral Statistics, United States Bureau of Mines, Washington, D. C.; Lloyd J. Lathrap, Superintendent, Nevada Quicksilver Mines, Inc., Lovelock, Nev.; W. R. Moorehead, General Manager, New Idria Quicksilver Mings, Inc., Idria, Calif.; F. W. Oakes, Jr., Terlingua, Tex.; C. N. Schuette, San Francisco. Brief Economic History of Quicksilver in the United States Quicksilver ore was first discovered in the United States at what was later the New Almaden mine in California, in the year 1824. Production also began here, but not until 1850, when it was stimulated by the active demand caused by gold-mining operations. Prospecting for quicksilver was active, high-grade ores were found and ample production lowered the price from $100 per flask in 1850 to about half that figure for the greater part of the next 10 years. During the succeeding decade, many new quicksilver mines were found; production increased at a time when the local demand diminished, so that most of the product was exported. The third decade of quicksilver mining in the United States witnessed the development of the pan amalgamation process, particularly in Com-stock silver-mining operations. A suddenly increased demand sent prices soaring, the all-time peak of quicksilver production followed, and the highest price was soon replaced by the lowest one on record. Huge quantities of quicksilver were exported between 1870 and 1880 and exports continued in decreasing measure for three decades to 1910. In

Jan 1, 1930

By Kenneth L. Cook

THE five serpentine masses exposed within the northern half of Riley County, Fig. 1, constitute a major part of the few exposures of igneous rock in Kansas.' Although not many subsurface data are available for this part of Riley County,2 six deep wellsV indicate that the basement complex lies between 2500 and 3000 ft below the earth's surface. A northwestward-trending ridge in the present basement surface, which extends across the northern half of Riley County, is indicated on Mettner's contour map.' The serpentine masses lie in a region that was active during Pennsylvanian and Permian time along two main tectonic trends, which may, in part at least, have developed contemporaneously." One trend is northeasterly, as evidenced by the Nemaha anticline, the Abilene anticline, the Voshell anticline, and many other smaller northeastward-trending folds. The other trend is northwesterly, as evidenced by the central Kansas uplift, the Salina basin syncline, and smaller northwestward-trending folds. The area of the Abilene anticline was actively deformed during much of this time, and the present surface rocks, for the most part Permian in age, show many normal faults." The Bala and Leonardville intrusions lie within a mile of the axis of the Abilene anticline, Fig. 1, as mapped by Wallace Lee;' the Randolph No. 1 and Randolph No. 2 intrusions lie within about 5 miles of the axis; and the Stockdale intrusion lies within about 8 miles of the axis. The igneous rocks have intruded horizontal or gently dipping limestones and shales that are late Permian in age.V he period of intrusion, according to Moore and Landes, was probably Cretaceous.' At present a detailed description of the petrography is available for only the Bala intrusion. Moore and Haynes' describe the rock at Bala as a green, serpentinized, porphyritic, peridotite breccia containing inclusions of shale. The ground mass consists chiefly of serpentine and calcite with considerable chromite (5 to 10 pct) and some magnetite. The phenocrysts consist principally of altered olivine with some altered augite and biotite. Although probably different in petrographic details, all the serpentine masses are somewhat similar in that 1) they consist of a dark green, fine-grained ground mass of igneous rock containing many xeno-liths composed of fragments of the neighboring sedimentary rock; 2) they tend to form small mounds on the landscape, thus indicating their greater resistance to weathering and erosion; and 3) they are magnetic. Previous Magnetic Survey of the Bala Intrusion: To the writer's knowledge, only the Bala intrusion had been surveyed with a magnetometer prior to the magnetic surveys discussed in this paper. Dreyer8 interprets the intrusion as a vertical, eastward-plunging dike, on the basis of the results of his magnetic survey, Fig. 1, with a vertical magnetom-

Jan 1, 1956

By C. S. Smith, L. H. Beck

KNOWLEDGE of the Cu-Zn constitution diagram was critically examined in 1944 by G. V. Ray-nor,1 who suggested the diagram reproduced in Fig. 1 as the best evaluation of available data. No pertinent work on the constitution has been published since that time, although a number of authors have discussed transformation kinetics and theory. Despite the large amount of work that has been done on the constitution of these industrially important and scientifically interesting alloys, minor uncertainties still exist. For example, it is still not possible to say definitely whether a two-phase region exists between the ordered and disordered forms of the 8 phase. A careful re-examination of the phase boundaries in this part of the diagram was therefore undertaken. Two methods were selected for the new investigation—quantitative metallography for the higher temperatures and precision lattice parameter measurement for lower temperatures. Because of the relatively narrow two-phase regions flanking the ß phase in these alloys, quantitative metallography is particularly suited for their examination, since the relative amounts of the two phases are very sensitive to their compositions. The method, however, is useless below about 350°C because of the inadequate resolution of the two constituents. Below 400°, however, the X-ray diffraction method is applicable, although it is of somewhat lower sensitivity in this system. The changes of composition that occur during quenching from above about 500°C entirely vitiate X-ray measurements at room temperature though they do not affect metallographic area measurements. The two methods overlap and supplement each other admirably. Both methods depend on the attainment of equilibrium composition of the two phases in a more or less intimate mixture and thus avoid the difficult problems of nucleation and long range diffusion involved in the conventional metallographic bracketing method. The alloys were melted from a master alloy made from re-electrolyzed cathode copper and Horsehead 99.99 pct Zn. Melting was done under a cover of either borax or charcoal and the alloys cast into a 7/8 in. sq graphite mold for the a-ß alloys or a 3/8 in. diam cylindrical graphite mold for the ß-? alloys. The a-ß alloys were rolled at 750°C to 5/8 in. sq; annealed for 24 hr at 800°C and quenched; then rolled and swaged at 200°C to 3/8 in. diam rods, annealed 24 hr at 200°C, quenched and cold rolled 2 pct reduction. This treatment was intended to obtain a small grain size and to produce many nuclei of the minor phase for growth on subsequent heat treatment. The unworkable ß-? alloys were given preliminary treatment by sealing in Vycor tubes in vacuum and annealing for 4 hr at 800°C followed by cooling in air. Samples of homogenized alloys were checked spectrographically for impurities, but the principal components were determined on samples subsequent to heat treatment. The impurities analyzed averaged approximately as follows: Ag, 0.0002 pct; Fe, 0.004; Si, 0.0008; Cd, 0.005; Mg, 0.0002; and Pb, 0.002. For metallography, samples of appropriate composition were cut into rods 5/8 in. long, sealed in pyrex tubes in vacuum and annealed for eight weeks at temperatures of 470°C and below, two weeks at 480°, 500°, and 600°C, and 4 hr at 700°C, followed by quenching in cold water. Temperatures were accurate to ±2°C. The cylinders were then machined to 8.7 mm diam and a slice weighing 1.5 g cut with a thin saw transversely from the center of each. This

Jan 1, 1953

By J. J. Kramer, G. W. Wiener, K. Foster

The effects of the primary grain size and sheet thickness on the secondary growth rates of grains with (100) surface planes were studied in 3 pct Si-Fe sheets. This secondary grain growth was carried out under conditions in which the {100} plane had the lowest surface free energy. The value of the surface energy difference, between the (100) plane and the random matrix planes was found to he only about 3 pct of the grain boundary energy, indicating that most of the driving force for secondary growth is supplzed by grain boundary energy. A method for obtaining cube texture in 3 pct Si-Fe sheets by a secondary recrystallization process has been reported.' It has been demonstrated that a difference in surface free energy between the (100) plane and other planes is responsible for this growth, where the (100) plane has the lowest surface energy. A semiquantitative relation has been derived for secondary grain growth in sheets where primary grain growth has proceeded until the grains have grown through the sheet and the average grain diameter in the plane of the sheet is from one to two times the sheet thickness. Then, the linear growth rate, G, for the secondary grains can be given by where M is the grain boundary mobility, is the grain boundary free energy, is the average primary grain radius, A is the average difference in surface free energy between the (100) plane and planes of other orientations, t is the sheet thickness, and C is a term first proposed by zener6 which acts as a negative driving force, the effect of inclusions in holding up grain boundary motion. Since the problem of grain growth being discussed is under conditions where the matrix grain size is at least equal to the sheet thickness, the radius r is, of course, a function of the sheet thickness. The term B/r is the grain boundary driving force normally associated with inclusion inhibited or texture inhibited secondary recrystallization. Here, however, the term is modified to account for the fact that growth occurs in thin sheets. The term is the additional driving force available because of the difference in surface free energy. The purpose of the present work has been to evaluate the driving force terms of the growth equation by studying growth rates of (100) secondary grains as a function of sheet thickness and primary grain size. From these data it has been possible to determine the relative values of grain boundary energy, surface energy difference, and the inclusion term, C. EXPERIMENTAL PROCEDURE A 3 pct Si-Fe alloy was melted and cast under a helium atmosphere using electrolytic iron and a pure commercial grade of silicon as raw materials. The alloy was hot and cold rolled to a thickness of 0.6 mm, and samples approximately 5 in. long by 1 1/4 in. wide were cut from the cold-rolled sheets. Four different primary grain sizes were obtained

Jan 1, 1963