Search Documents

By V. O. Struebing, K. A. Johnson, F. H. Ellinger, C. C. Land

The system Pu-Ce-(Pu,Ce)Co2 has been investigated by thermal, micrographic, and X-ray diffraction methods. The principal characteristics of this system were found to be: 1) a "eutectic" valley extending across the phase diagram from the 6 Pu/Pu3 Co eutectic at 408°C to the 7 Ce/Ce24Co11 eutectic at 42Z°C, the maximum temperature in the valley being 443°C; 2) three ternary inter mediate phases, each having an appreciable mutual solid solubility for plutonium and cerium; 3) eleven four-phase equilibria comprising one eutectic, four peritectics, and six Class II reactions; 4) a pseudobinary section between the ternary phase A and the y Ce solid solution, and another such section between the 6 Pu solid solution and the 77 phase (Pu3 CO) containing cerium in solid solution. ALLOYS of plutonium that are completely molten at temperatures in the vicinity of 500°C are of interest for use in the liquid state as fast reactor fuels. Since exploratory work1,2 on Pu-Ce-Co alloys had indicated that a "eutectic" valley extended across the ternary system between the Pu-co[6 Pu/n (Pu3co)] and the Ce-CO[? Ce/? (ce24co11)] binary eutectics, thus allowing alloys of any plutonium concentration to be selected within the temperature limitation, the present investigation was begun for the purpose of accurately defining the "eutectic" valley. However, when the existence of three ternary intermediate phases and the consequent complexity of the liquid-solid equilibria were discovered, the investigation was expanded to cover the complete system, except for the corner between the isomorphous series PuCo2-CeCo2 and pure cobalt. 1) EXPERIMENTAL The purities of the alloy components are given in Table I. Alloy buttons, each weighing about 5 g, were prepared by arc melting the accurately weighed components (±0.1 mg) under a purified He-Ar atmosphere. Weight loss as a result of melting was usually less than 1 part in 1000; therefore, the buttons were not chemically analyzed. One half of each button was re-melted by induction heating in vacuo in a magnesia crucible and furnace-cooled, so as to produce a somewhat coarser microstructure than that of the rapidly cooled arc-melted button. About 20 g of each alloy to be examined by thermal analysis were remelted in vacuo in a tantalum crucible of the inverted thermocouple well type. The thermal, X-ray diffraction, heat treating, and micrographic methods used in this investigation were essentially the same as have been described in earlier reports.3,4 Two etchants for these alloys were found to be satisfactory: A) 8 (parts by volume) orthophosphoric acid, 5 ethanol, and 5 glycol; B) 7 tetraphosphoric acid, 36 water, and 57 2-ethoxyethanol. Etchant A was used at 5 to 6 v for 15 to 20 sec, and etchant B was used at 10 v for 10 sec. 2) THE LIMITING BINARY SYSTEMS 2.1) Plutonium-Cerium. The phase relationships of this system have been investigated by Ellinger, Land, and Cramer,5 and by Selle and Etter.6 The over-all agreement of their phase diagrams is good, but there are some discrepancies in the positions of some phase

Jan 1, 1967

By James Elton

THIS paper covers, besides laboratory work, a study of actual operation at the Washoe Smelter over a considerable period of time, together with the results of a visit to the Midvale plant of the United States Smelting- & Refining Co., near Salt Lake. For the latter privilege, as well as permission to publish the resulting data herein given, I am indebted to George W. Heintz, General Manager of the Midvale plant, and here take pleasure in. expressing my appreciation for the many courtesies extended to me by Mr. Heintz and members of the technical staff at the smelter. Almost all of the world's supply of arsenic is recovered as a by-product in the smelting of other metals. It is seen on the market in various forms, the most common being arsenic trioxide, the ? white arsenic " of commerce, which is sold as a heavy white powder, or in white, glassy, translucent masses. The trioxide is used in the manufacture of pigment, glass, and insecticides. About 50 per cent. of the domestic consumption is supplied by imports.

Jan 8, 1913

By J. F. Blandy

IN October last, I was call upon to examine a copper deposit in the South Mountain, near the Pennsylvania and Maryland boundary. The specimens shown me contained oxides and carbonates with native copper, and were similar to some that had been described to me some years ago as existing at the Luray Gap in Virginia. An examination of Rogers's Report on the Geology of Pennsylvania, led me to expect to see his so-called "Primal Formation," such as exists throughout the southeastern district of the State. I was therefore much surprised on arriving at the summit of the Western Maryland Railroad to find myself on familiar ground. Instead of the "Primal" as I had known it in Southeastern Pennsylvania, I soon decided that the rocks were identical with the "Lake Superior Copper Formation." My visit was unfortunately a short one, part of two days, and in that time I had to pass over a good many miles, but I saw sufficient to convince me that instead of the Lake Superior Copper Formation being a local geological feature, it would have to be considered as a widely extended series of rocks. I was unable to even approximately estimate the thickness either of the trap zone or other members, schists and slates, of the series. In an article on the Copper Range of Michigan, prepared by C. P. Williams and myself in 1862, and published, in vol. xxxiv of the American Journal of Arts and Sciences, we endeavored to divide that range into zones, according to the character of the traps. The limited nature of the explorations at that time made this work very imperfect. Subsequent explorations have confirmed my notes then

Jan 1, 1879

By J. F. Blandy

In October last, I was call upon to examine a copper deposit in the South Mountain, near the Pennsylvania and Maryland boundary. The specimens shown me contained oxides and carbonates with native copper, and were similar to some that had been described to me some years ago as existing at the Luray Gap in Virginia. An examination of Rogers's Report on the Geology of Pennsylvania, led me to expect to see his so-called "Primal Formation," such as exists throughout the southeastern district of the State. I was therefore much surprised on arriving at the summit of the Western Maryland Railroad to find myself on familiar ground. Instead of the "Primal" as I had known it in Southeastern Pennsylvania, I soon decided that the rocks were identical with the ('Lake Superior Copper Formation." My visit was unfortunately a short one, —part of two days, and in that time I had to pass over a good many miles,—but I saw sufficient to convince me that instead of the Lake Superior Copper Formation being a local geological feature, it would have to be considered as a widely extended series of rocks. I was unable to even approximately estimate the thickness either of the trap zone or other members, schists and slates, of the series. In an article on the Copper 'Range of Michigan, prepared by C. P. Williams and myself in 1862, and published. in vol. xxxiv of the American Journal of Arts and Sciences, we endeavored to divide that range into zones, according to the character of the traps. The limited nature of the explorations at that time made this work very imperfect. Subsequent explorations have confirmed my notes then

Jan 1, 1879

By AIME AIME

AS director of Battelle Memorial Institute and as Chairman of the important O.P.M. advisory committee on metals and minerals, Clyde E. Williams numbers his acquaintances in the mineral industries by the thousands and h because his principal hobby is liking human beings, most of his acquaintancs are also his friends. Clyde is one of the many outstanding metallurgist, in the United States who started as a chemist. After graduating from the University of Utah in 1915 he was successively chemist for U.S. Smelting Refining and Mining Co., and at the Bureau of Mines station at Ithaca, N.Y. He then got into, metallurgical work and in 1920 he was appointed superintendent of the Northwest Station of the Bureau of Mines at, Seattle. Subsequently he was assistant to H. Foster Bain in metallugical work for the

Jan 1, 1942

By Edward H. Robie

SUBJECT to formal Board approval in September, AIME dues will continue indefinitely at the present scale of $20 for Members and Associate Members; and $12 for Junior Members for the first six years of such membership, thereafter $17. That is the wish of the Board of Directors and the will of the membership, as expressed in the recent referendum. Though the official returns, as reported by the tellers, are not available as this is written, the data are sufficiently complete to give the results to the nearest percent. The total vote was approximately 93 pct for continuance of the present scale. Metals Branch members voted about 94 pet for continuance; Mining Branch members slightly less than that; and Petroleum Branch members about 91 pct. As in the referendum of 1949, there was no particular difference of opinion on the question of dues as between the three Branches. The percentage of ballots returned was about 61 pct, only slightly more than in the 1949 referendum. But the affirmative vote was much greater, 93 pct against 78 pet in the earlier referendum. Looked at another way, a majority of those to whom ballots were sent, 56 pct, voted to continue the present scale of dues, whereas only 46 1/2 pct of those canvassed voted to raise the dues in the previous referendum. But approximately 600 , members expressed their opinion that the dues should go back to $15 for Members and Associate Members and to $10 and $15 for Junior Members. This is a substantial group of members who either do not think they are getting their money's worth from AIME membership, or believe that a more businesslike conduct of Institute affairs should provide current services at less cost, or believe that more service is being provided for their dues than they need. As to the first point, it is probable that some members are not getting their money's worth. They perhaps have only a fringe interest in. AIME activities, or they do not or cannot participate in such activities at the Local Section, divisional, or national level, so that all they get out of the Institute is the monthly journal, which they do not have time to read. If they did read it intelligently, and acted upon the professional information thus gained, it is difficult to understand how one or more ideas cannot be gained that would be worth $20 to them professionally. But the 600 members who want lower dues offer a challenge to the Directors and to the staff to do a better job; to make Institute membership so rewarding that every. member will be thoroughly satisfied. Twenty 1935 to 1939 dollars are worth only $11.60 now, according to the latest government data, but that makes it all the more necessary for us all to appraise the value of what we buy. To the 93 pct of Institute members who expressed a vote of confidence, so to speak, the staff, and we feel sure the Directors as well, are most appreciative and thankful.

Jan 1, 1952

By L. W. Casteel

This is a story of progress through research, invention and innovation-progress that made a small mine in Missouri into a large and prosperous corporation. The St. Joseph Lead Co. was founded in Borne Terre, Missouri, in 1864. At that time, the mine consisted of a narrow trench eight feet deep; the mill was a hand-operated jig; and the smelter, a charcoal oven with a sloping hearth. During the first year, production was suspended for two months because of an invasion by the Confederate army. There have been few interruptions since that time.

Jan 7, 1964

By J. R. Thompson

It is common practice, and certainly good business as all of us know, to take care of plant operating equipment. Machinery of any type requires periodic inspection and planned maintenance. With this thought in mind a plant operator should at the end of every shutdown period make regular belt inspections and plan for later appropriate care and maintenance. The points mentioned below are understood well by all of us but are sometimes forgotten because belt conveyors are comparatively easy to operate. Maintenance of any conveyor belt is dependent upon the fundamental characteristics of the two component parts-cover and carcass.

Jan 6, 1950

By Leendert de Witte, Fred J. Radd

In many areas caring failures can be directly related to electrical currents observed in the casings. It is the thesis of this paper that the observed casing currents are mainly due to electrochemical potentials of the type in evidence on spontaneous potential curves of electrical logs. The general nature of these potentials are discussed and an equivalent circuit is given for current and potential distributions around open holes. The casing forms a short circuit to these potentials and tends to average the effects of local cells. The case of casing corrosion opposite the Dakota water sands in the salt-mud area of Kansas is discussed anil used us a qualitative, illustration of the relation between SP's and casing currents. A method of quantitative derivation of casing current distribution frorn electric log SP curves, using linear transform theory, is described and results are compared with a measured current profile. The effects of hydrogen over-potentials at the cathodic portions of the pipe are considered and some laboratory data are given in support of conclusions regarding the over-1.01tuge.s. INTRODUCTION To date an appreciable amount of work has been done on the measurement of oil well casing currents and on the correlation of the anodic portions of the current profiles with corrosive casing failures. Speculations on the origin of the casing currents have, however, remained rather vague; and although almost every plausible cause has been mentioned, there is to the writers' knowledge no clear-cut expose' on the details of the causes of the corrosive currents in the literature. A study of current surveys and casing failures in the N.W. Burnett field, Ellis County. Kan.. indicated the probability that concentration cell emf's between the Wellington salt section and the relatively fresh waters in the Dakota sands were a major cause of the corrosion currents. A more general concept evolved upon analysis of the severe corrosive conditions in the Pleistocene sands in the Ventura Avenue and San Miguelito fields in California. In this area no major variations in the salt content of the formation waters occur and yet large casing currents are observed. An explanation is found in the fact that the local spontaneous potentials which are set up due to concentration contrast between the drilling fluid and the connate water are short circuited when casing is set. The very conductive path through the casing increases the magnitude of the currents and has the tendency to average local sources over fairly large intervals. Current will flow between the sections that are predominently shaly and the sections that are mostly sandy. At the places where the current leaves the pipe, corrosive attack will occur. This same phenomenon will be present wherever unprotected pipe is set through sections that show large SP kicks on the electric logs over reasonably thick interval~. GENERAL- NATURE OF THE SPONTANEOUS POTENTIALS When a sequence of sedimentary rocks is penetrated by a drill hole filled with a mud which has a different salt concentration from that in the formation waters, various types of electrochemical potentials are established between the formations and different parts of the mud column. Opposite clean sand sections. a simple liquid-liquid junction potential will be observed; while opposite argillaccous formations, a membrane potential, often referred to as shale potential, will be established. The first quantitative analysis of these emf's in terms of liquid junction and membrane potentials is due to Wyllie.1

Jan 1, 1956

By A. J. Shaler, J. Prieto Isaza, John Wulff

TANTALUM metal has a number of unique properties which give it widespread application in modern technology and in research. In electronic apparatus involving high temperatures in vacuo some of the refractory metals become brittle. Tantalum retains its ductility at elevated temperatures, and this property, together with its low vapor pressure and its ability to absorb gases, make it important in this field. Its chemical inertness in the presence of acids, halogens, and other corrosive media, makes it useful in chemical apparatus and in neuro and orthopedic surgical applications. As an addition to tungsten carbide in steel-cutting grades of cemented-carbide tools, the carbides of tantalum and of its sister element columbium have found considerable use. The present-day method1 of manufacturing tantalum is to sinter a powder compact of the metal in vacuo. Because tantalum- columbium alloys are difficult to work and since tantalum ores almost always contain columbium, the two metals must be separated chemically, the products of the separation being generally in the form of potassium tantalum fluoride and potassium columbium oxyfluoride. These salts are used in fused-salt electrolytic baths from which coarse metallic powder is deposited as a sponge at the cathode. Finer powder can be made from the coarse product or from tantalum scrap by first submitting it to an embrittling heat treatment in hydrogen and then crushing it. The fine hydrogen- containing powder may subsequently be degassed in vacuo at a high temperature. Prompted by the success of others2,3 in the magnesium reduction of titanium and zirconium halides, one of the authors under- took4 an investigation of the thermo- chemistry of the reaction between solid magnesium and gaseous tantalum penta-chloride, a subject which had not previously been studied. He found that the heat of formation of tantalum pentachloride is approximately 364,250 cal per mol at temperatures lower than the melting point of magnesium. A value of 83 units was found for the standard entropy at these temperatures. With these values, it was shown that magnesium and tantalum pentachloride are capable of reacting exothermically at temperatures less than the melting point of magnesium, and that no great violence is to be expected when these substances are heated together. The exothermic nature of the reaction indicated that the process should be efficient and should not require much externally applied energy. Tantalum pentachloride is not commonlv made commercially, and any process using it therefore involves the subsidiary problem of producing and handling this substance. A series of experiments was carried out in which dried chlorine saturated with carbon tetrachloride was passed over heated tantalum, either in the metallic state or combined

Jan 1, 1947

By Arnold Hague

In the short time allotted to me* I can only hope to present to you a brief sketch of the main geological features of the country which you are about to visit. My remarks must, of necessity, be more or less incomplete, as my desire is not so much to elucidate any special problem connected with the many interesting geological questions to be found here, as rather to offer such a general view of the region as will enable you, during your five days' trip through the Park, to understand clearly something of its physical geography and geology. The Yellowstone Park is situated in the extreme northwestern portion of the Territory of Wyoming. Its boundaries, as determined by the original Act of Congress setting apart the Park, are very ill-defined. At the time of the enactment of the law establishing this national reservation, the region had been but little explored, and its relation to the physical features of the adjacent country was but little understood. Since that time, surveys have shown that only a narrow strip, about two miles in width, was situated in the Territory of Montana, but it was also found that a still narrower strip extended westward into the Territory of Idaho. The question of properly establishing the boundaries, -based upon our present knowledge of the country, is now before Congress, and an Act has already passed the Senate, proposing to make the northern boundary coincide with the boundary between Wyoming and Montana, and the western boundary coincide with the Wyoming and Idaho line. The Act under consideration extends the southern boundary of the Park to the 44th parallel of latitude, carrying the area of the reservation southward nine and one-half miles. The eastern boundary is made to coincide with the meridian of 109' 30') adding a strip of country about twenty-four and one-half miles in width along the entire eastern side of the Park.

Jan 1, 1888

By Pierre Hines

THE. Owyhee Tunnels in eastern Oregon were started in the early part of 1930, and were completed early in 1932, with the excep-tion of the Magoffin contract. One tunnel is a large water tun-nel, and the other is a small water tunnel; each is approximately tour miles long. Modern equipment was used to full advantage, and remarkably fast time was made during the driving period. The ,J. F. Shea Co., con-tractors, of Portland, Oregon, have broken established records in the smaller tunnel. Their methods are described in detail. The time of a complete round has been reduced by intelligent handling of mechanical shoveling, and this article records some of the useful facts developed. Charles A. Shea (president of the J. F. Shea Co., and secretary of The Six Companies, Inc.) not only granted permission to publish this article, but placed the company's complete daily reports at the writer's disposal. These reports were made out to conform with previous records upon important tunnel work, and enable a comparison to be made of actual averages, rather than ideal cycles, or representative cycles. Gilbert Shea, present superintendent, has been helpful with time, criticisms, and corrections of the information presented. Morton S. Boss, superintendent during the first 15 months of the tunnel work, gave many hours of his time during two visits lasting over two weeks. The whole staff of the J. F. Shea Co. has given encouragement and assistance.

Jan 1, 1933

By R. A. Wagstaff

THE method of charging a reverberatory furnace has changed many times since smelting was introduced in this country from the old smelters of Swansea, England. The cause of the latest change at the Garfield plant has been the excessive fineness of the charge due to fine grinding in the concentration of the crude copper ores. The many desirable features of deep-bath smelting as now used at Garfield have been proved. The old method of dropping the charge through holes in the arch (known as center-feed method) causes excessive dusting which makes heavy slag and causes flue-dust losses, also rapid deterioration of the silica brickwork of the furnace through fusion .with the iron oxides from the dust. The purpose of this paper is to describe a gun feeder that was designed to overcome the disadvantages of the older methods of center feeding and still maintain the good features of deep-bath smelting with the hot finer charge. A gun feeder was designed to introduce the finely divided hot calcines under the moving gas stream of the combustion zone and still have them spread in a uniform blanket over the highly heated matte bath. The temperature of the furnace was so great that it was impossible to maintain a stationary feeder, so a movable feeder was designed that could be introduced into the highly heated zone and be withdrawn after the charge had been dropped. It was necessary to protect the nozzle of the gun with a water-cooled coil. Many different types of protected nozzles were tried, such as air jackets, water jackets and heat-resisting steel alloys, but none proved satisfactory.

Jan 1, 1932

By D. C. Bard

THESE notes are based on the megascopic study of a suite of 2,400 specimens of minerals and ores from the Butte mines, combined with field observations at intervals over a period of several years. The estimate of average vein composition is based on field acquaintance with the veins. It is probably correct in its broader proportions, and should be of use for comparison. Chemical and Mineral Composition of Butte Sulphide Vein. Matter. Per Cent. Oxygen 43.00-Quartz, rhodonite, rhodochrosite, barite, calcite, and hübnerite. Silicon 36.00-Quartz, rhodonite, and willemite (very rare). Sulphur 5.00-Sulphides of. iron, zinc, copper, lead,. and sulphates of barium and rarely calcium. Iron 5.00-Ferric sulphides (pyrite, bornite, chalcopyrite), also in sphalerite, tetrahedrite, and rarely hematite and siderite. Manganese, . . . . 2.00-Rhodonite, rhodochrosite, and hübnerite. Zinc, . . . . 1.00-Spha erite, very rare wurtzite and willemite, and tetrahedrite and tennantite.

Jan 8, 1913

By M. A. Mayers, J. A. Thompson

In recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.l-14 Only in Russell's method" and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼-in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C, consisting of two annuli of 0.011-in. (o.a8-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By J. A. Thompson, M. A. Mayers

In recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.l-14 Only in Russell's method" and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼-in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C, consisting of two annuli of 0.011-in. (o.a8-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By Eduardo J. Chibas

Location.—The principal manganese-deposits of the Department of Panama, Republic of Colombia, are located almost clue south of Viento Frio, a native village bordering on the Caribbean Sea, and about 45 miles northeast of Colon (Aspinwall). The mining-claims are the Viento Frio, the Carrano, the Nispero, and the Soledad. Each property is to the south of the preceding one in the order mentioned. The first one is about one mile from the coast, and the most southerly boundary of the Soledad is about five miles in a straight line from the same coast-line. I shall confine my remarks to the four properties mentioned and to La Guaca, west of the Carrano, because these are the only ones where mining has so far been done to more or less extent. Manganese has also been found, however, in the neighborhood of these deposits, and a large area adjoining them has been divided into sections and " denounced " as mining-claims. The relative position of the manganese-deposits and Nombre de Dios, the present terminal of the railroad and shipping-port, as well as Viento Frio and the adjacent coast, can

Jan 1, 1898

By Charles T. Holland, David A. Olsen

Considerable work has resulted in the development of a formula by which the strength of coal pillars for an L to T ratio of up to 12 may be estimated. One of the factors involved in this formula is the coefficient of friction between the coal pillar and the adjacent rock with which it is in contact. This paper presents the results of studies on sandstone, limestone, shale and coal and the coefficient of friction between coal and the other three under wet and dry conditions. With the coefficients of friction thus determined and the use of results obtained earlier by Meikle and Holland, it seems probable that coal pillar strength may be more closely estimated. Several investigators1-3 have found that the com-pressive strength of cubical coal specimens can be correlated by an equation such as

Jan 1, 1969

By Roscoe C. Clark

A study of the effect of various corrosive waters on five different types of cements indicated that those cements containing less than 5 per cent tricalcium aluminate were the most resistant to corrosion. INTRODUCTION Oil field experience indicates that some formation waters are excessively corrosive to some cements. A study has been made to determine the most corrosive waters and the relative resistance of various types of cement to these corrosive waters. PROCEDURE This study of the corrosion of cement was limited to an evaluation of the effect of various corrosive waters on five different types of cements. A determination was made of the types of cements which offer the greatest resistance to corrosion and of the chemical contents of waters found to be the most destructive to cements. The laboratory tests were conducted by immersing small cylinders of 20 samples of set cement in various corrosive waters. The initial mixing of most of the cement slurries was done using Tulsa tap water as the mixing water; however, a few of the slurries were mixed using a sulfate water as the mixing water. When the 20 samples had been immersed for a period of nine months, they were removed from their corrosive baths, inspected and photographed. The field tests were conducted by placing ten cement specimens, each contained in a screen wire thimble, in the gas anchors of insert pumps in wells in six different fields. The specimens were observed whenever it was necessary to pull the pumps and were returned to the 1aboratory when deterioration had reached a serious state. EXPERIMENTAL RESULTS In both the field and laboratory tests the resistance of the different cements to corrosion was determined by the condition of the samples and the number of samples of each that were in good condition at the end of the immersion period. Table I lists the various cements tested in the order of their resistance to corrosion with the most resistant at the top and the least resistance at the bottom. An analysis of Table I reveals that the upper half of the table predominates in slow set and sulphate resisting cement.: (low 3CAO.A12O3 content) while in the lower half the port-land and high early strength cements are in the majority. Of the last two the high early strength cements appear to offer less resistance to sulfate water corrosion. An investigation of the composition of the cements listed in Table I indicated that as a general rule the cements containing less than five per cent tricalcium aluminate will exhibit the greatest resistance to corrosion. The destructive action of various corrosive waters was compared by listing the waters in the order of those containing the largest number of samples that failed completely. These ratings are presented in Table II with the most corrosive waters listed first and the least corrosive last. Figs. 1 and 2 show the end views of cement samples which had been immersed in the baths of five per cent MgSO, water and the five per cent Na2SO4 water respectively in the laboratory. These .pictures are representative of the results obtained and present a pictorial evaluation of the corrosive resistance of various types of cements.

Jan 1, 1950

By B. R. Banerjee

MATERIAL used throughout this investigation was high-purity aluminum (99.998 pct). The 1/2-in. cubes were cut out of a cold-rolled slab and annealed at 550°C for 1 hr before deformation. The single crystal specimen was 1 in. in diam x 0.33 in. thick, cut from a cylindrical crystal produced by cooling at about 55°C per hr in a furnace which had a convenient gradient of about 10°C in every 4.5 in. vertical crucible length. Specific data on the ten specimens studied are summarized in table I. Three types of deformation were employed: (I) compression in a hand-operated hydraulic press; (2) impact with a 7-lb sledge hammer; and (3) rolling, using a wedge-shaped specimen' to obtain a gradient of deformations varying from 0 to 50 pct along the length of the wedge. Specimens were either deformed at room temperature, or first cooled in a freezing mixture of dry ice and ether at a temperature of —72°C and then deformed between steel blocks cooled with dry ice. The specimens deformed at the low temperature were ground and polished through 000 emery paper and wheels impregnated with alundum and alumina No. 1. During this entire procedure the specimens were dipped frequently in the freezing mixture of dry ice and ether in order to maintain constantly a frosty surface as insurance against overheating. All specimens were given a final electrolytic polish, using two different electrolytes* to insure that the surface effects observed were not char- acteristic of the polishing technique. With both electrolytes, the annealed specimens gave even surfaces with good polish. Several standard etchants were tried without success. The best results were obtained with an immersion etchant, developed in this connection, containing: hydrofluoric acid, 4 parts; nitric acid, 1 part; glycerine, 3 parts. Discussion of Results Typical strain markings have been observed within deformation bands, as shown in figs. 1, 2, and 4. By stereographic plotting of metallographic measurements, the strain markings within a deformation band in a single crystal of aluminum deformed by compression were found to be traces of (111) planes within a maximum scatter of 6". The edges of the deformation band were found to be traces of the (100) planes also within the maximum scatter of 6" (in agreement with previous workers). At 30 pct deformation, this scatter was considered quite normal because of the fragmentation and rotation of the crystal. This solution, based on the traces on one plane of observation is not unique, but as the planes were observed to be those normally and logically to be expected, further work in this regard was not felt to be necessary. The study of strain markings in a wedge-shaped specimen, rolled to obtain a gradient of deformation from 0 to 50 pct, revealed prominent strain markings at 25 pct reduction in thickness (fig.5). Faint and weak strain markings were visually observable up to a minimum reduction in thickness of about 12 pct. Since strain markings have been observed in other face-centered cubic metals after much smaller deformations;1, 2 and since the rate of recovery in aluminum is high, it is believed that, at lower deformations, self-recovery removes the localized strains at the slip interfaces, thus removing the source of the etching effects that give rise to strain markings. At high magnifications, strain markings sometimes seem to appear as very thin, light-banded re-gions bounded by a pair of dark edges. This so-

Jan 1, 1951