Search Documents

By Gilbert Santoro

In this study tantalum carbide filaments of various compositions in the fcc region were prepared by heating a tantalum wire in a measured amount of hydrocarbon vapor. Such properties as tensile strength, transverse-rupture strength, microhard-ness, lattice parameter, electrical resistivity, and magnetic susceptibility were measured as a function of carbon content. Some of these properties showed a maximum or a minimum between a carbon-to-tantalum molar ratio of 0.80 and 0.85, the composition range at which the color changes from metallic gray to gold. The recent literature has shown that in the large homogeneity range for the fcc phase of the Ta-C system there is a marked variation for such properties as microhardness,' electrical resistivity, ' thermodynamic properties,z'3 lattice parameter and superconductivity. In addition to the technological interest of these variations within a single phase, important theoretical benefits may ensue from a continuous investigation of properties vs stoichiometry in tantalum carbide and other refractory defect compounds, for example the effect of the metal-metal distance and crystal structure upon bond formation and electronic structure. Whether there is a similar variation of the tensile strength is of practical importance. Of theoretical interest would be the knowledge of how the magnetic susceptibility varies with carbon composition. Both of these properties, as well as the transverse-rupture strength, were determined for tantalum carbide filaments in the fcc phase region. The lattice parameter, the electrical resistivity, and the microhardness were also investigated and compared with values appearing in the literature. EXPERIMENTAL PROCEDURE Material Preparation. Tantalum carbide specimens of various carbon content were prepared by statically carburizing high-purity tantalum filaments in measured quantities of pure hydrocarbon gas. The filaments, which were 10 mil in diameter and 20 or 40 cm long, were heated by their own resistance at temperatures from 1800" to 2200°C using alternating current in some cases and direct current in others. Tantalum wire from two sources was used. One had a reported purity of 99.96 wt pct Ta. The ingot from which this wire was drawn had been electron beam-melted as the final step in its purification. The reported purity of the other wire, which was prepared by a powder metallurgical process, was 99.88 wt pct Ta. The impurities of both tantalum sources are listed in Table I. Spec-trographic-grade toluene or research-grade propane was used as the source of carbon. The apparatus for the carburization of the filaments is shown schematically in Fig. 1. The system was evacuated to 1 x l0-' mm of Hg when using the electron beam-melted tantalum and to less than 1 p when using the less-pure tantalum. Neither the difference in the base vacuum, nor in the hydrocarbon gas, nor in the tantalum filaments resulted in any detectable difference in the properties studied in this work. However, only the carbides prepared from the higher-purity tantalum were used in the magnetic-susceptibility determinations. Once the base vacuum had been reached, the system was flushed with the hydrocarbon and re-evacuated. For any desired composition of the carbide, hydrocarbon gas was allowed to leak into a constant-volume flask to a predetermined pressure. These pressures were measured by a Cartesian diver-type mercury gage with a range from 0 to 20 mm and with a scale expanded to nine times. The hydrocarbon gas was allowed into the reaction tube and the filament was quickly raised to the reaction temperature. The slack in the filament due to thermal expansion was taken up by drawing out the movable electrode with a screw mechanism. The filaments were kept at temperature from a few minutes to 200 hr. In the majority of cases the heating time was 6 hr. The reaction tube was cooled by cascading water on its outer surface. By means of an ammeter and a voltmeter the electrical resistance at the reaction

Jan 1, 1963

By Eric Jette

THE unusual physical, electrical and magnetic properties of the iron-nickel alloys has given rise to a voluminous literature. This work will be reviewed critically in "The Alloys of Iron and Nickel," a monograph of the Alloys of Iron Research Series, soon to be published. In what follows we shall therefore confine ourselves to those of the earlier investi-gations that involved the use of X-ray crystal-structure methods. The earliest X-ray work on the iron-nickel system was by Miss Andrews1. Using the powder method of X-ray analysis purely as a means of identifying the phases present, she located a region between 20 and 30 weight per cent nickel in which body-centered and face-centered phases coexisted. No lattice constants nor details of heat-treat-ment were reported. Bain2 also reported some qualitative observations. McKeehan3 made a systematic investigation over the whole of the system, giving many of his alloys four and some five different heat-treatments. In alloys furnace-cooled from 900° to 950° C. he found two coexisting phases between 0.15 and 30 per cent nickel. The precision of the lattice-constant measurements was low in comparison with what can be obtained today.. Even for alloys of the same heat-treatment, differences in the constants were often between two and ten parts per thousand. In regions where no change of lattice constant with heat-treatment should occur, differences of the same order of magnitude were found. Since the maximum change in the lattice constant of nickel with change of composition is only about 2 per cent of the constant for pure nickel, these variations in the constants for a given alloy cause the points

Jan 1, 1936

By R. S. Handy

DOES hand-sorting of mill feed pay? The fact that the practice is so general would seem to indicate that there must be good reasons for following it; yet, to my mind, the advantage in many cases is doubtful enough to invite a thorough discussion of the subject, in an effort to determine under what conditions hand-sorting does pay. A typical sorting plant in the Coeur d'Alene district handles about 800 tons of mine-run ore per day. The material is run over a grizzly with about 4-in. opening; the oversize is crushed to about 4-in. size and joins the undersize, and the whole product is washed and screened on trommels with about 1 ½ -in. openings. The oversize from these trommels is spread on a belt and the waste and first-class ore are sorted out by hand, the residue being further crushed, and passes, together with the trommel undersize, into the mill feed bins. About 50 tons of shipping ore and 150 tons of waste are sorted out per day, leaving about 600 tons of mill feed. To sort out this material requires 20 ore sorters and five bosses and repairmen. The normal cost of hand-sorting is about 16 c. per ton of run-of-mine ore, or 65 c. per ton of material sorted out. I believe that straight crushing and milling of the run-of-mine ore, in this case, is not only cheaper, but is metallurgically moree canonical and efficient than hand-sorting followed by milling of the residue. At one of the Bunker Hill rock-houses, 1250 tons of run-of-mine ore are reduced to pass 30-mm., or about 1 ¼ -in. opening in six hours, requiring five men. The equipment and the power consumed are not greatly different from that required in a sorting plant of the same capacity, and the normal cost of thus preparing the feed for milling is under 3 c. per ton of mine product. The relative cheapness of this method as against hand-sorting is thus clearly established, the saving being about 13 c. per ton. If there is any virtue in hand-sorting, then, it must lie in the metallurgical results achieved.

Jan 4, 1918

By G. L. Oldright, T. B. Brighton, C. M. Dice

The base bullion from the lead blast furnace contains varying amounts of the impurities left in the smelter feed by the concentrator, regardless of the method of smelter operation. These impurities may be held in part in mechanical suspension rather than being present as true alloys. However, usually there is little free space in the crucible in which to separate these drosses before the bullion is taken from the lead well. When such a dross is melted in a laboratory crucible and allowed to cool, the products obtained are lead bullion, speiss, and matte in well separated layers. Typical analyses of layers are: Analyses. Per Cent Element Bullion Speiss Matte Pb.............................................. 92.0 41.2 38.3 Cu.............................................. 2.4 36.3 40.6 As............................................... 4.0 16.5 4.3 Sb............................................... 0.7 0.2 0.4 S................................................ 0.6 1.9 13.1 Fe............................................... 0.0 0.0 0.0 Totals......................................... 99.7 96.1 96.7 The absence of iron in these products drossed from the blast-furnace bullion proves that the impurities for the greater part are not simply finely divided blast-furnace speiss or matte that has been dissolved or dispersed in the lead, but are held in solution by the liquid metal and rise to its surface as infusible compounds when the temperature of the bath is lowered. In general, the drosses made locally are metal sulphides and arsenides and not oxidized compounds. The large content of metallic lead also does not seem to be retained because of oxidized compounds

Jan 1, 1937

By A. M. Gaudin

IN flotation lime is used to depress pyrite. For this purpose it is preferred to caustic soda. The low cost of lime and the widespread availability largely account for this preference. However, there is some evidence1 that pyrite is more readily depressed by calcium than by sodium ions at the same pH. To measure the difference in adsorption of calcium and sodium, which is thought to lie at the basis of the differences in depressing action, radionuclides of

Jan 2, 1953

By M. B. Ramachandra Rao

THIS paper records the results of the earth resistivity surveys made in the Godavari river in connection with the Ramapadasagar project. After describing the topographical and geological features of the area, the results of the investigation at the several sites have been mentioned. Further, a detailed account has been given of the resistivity methods adopted, the apparatus used and the interpretation of the curves. The resistivity measurements carried out over the water course have been specially outlined, and a review of the verification of the electrical indications by drilling in a number of cases, has also been presented.

Jan 1, 1947

By A. G. McGregor

IN THE Southwest a number of large steel chimneys discharge the gases from the copper smelting furnaces. Some of these chimneys show no deterioration after twenty years, others show serious deterioration after tour years service. A steel stack 20 ft. 7 ½ in. (6.3 m.) in diameter by 279 ft. (85 m.) high, Fig. 1, used for roaster gases only at the Calumet & Arizona Mining Co.'s plant at Douglas, Ariz., was lined to the top of the bell, 40 ft. (12 m.) from the base, with common brick placed on end, lime and cement mortar being used. Above the bell, the stack was lined with 4 by 4 by 8 in. (10 by 10 by 20 cm.) building tile, placed on end, making a lining 4 in. thick. The tiles were supported on angle-iron rings, riveted to the inside of the chimney shell about 15 ft. apart. The chimney was put into use in the latter part of 1913. Four years later, considerable of the tile lining had fallen out of place and mixed with the flue dust at the bottom of the chimney. About a year later, several . flattened and distorted sheets were noticed about 70 ft. below the top. An investigation showed that the thickness of these distorted sheets, which was originally ¼ in., had been reduced one half. One year later, or six years after the chimney went into use, several holes, a square foot and smaller in area, appeared near the flat spots mentioned. Soon afterwards, when the chimney was shut down for repairs, it was found that most of the tile lining for 125 ft. from the top had fallen out and that the steel shell was badly corroded; but where the lining remained in place the shell was undamaged. Many of the tile which had fallen out of place had become soft or flaky and crumbling, others were as hard as when placed. An analysis of the hard and soft tile is shown on p. 2. These tile were of a fireclay mixture, and were used instead of common brick on account of lower cost. The steel forming the upper 125 ft. (38 m.) was replaced, and a 4 ¼ -in. (11-cm.) lining of firebrick was laid from the bell to the top of the chimney. The brick were placed on end, wedges and keys being used. After each 8-in. course was set, keyed, and wedged tight, thin mortar -water, sodium silicate, and finely ground silica-was worked into the joints. The brick are supported on angle-iron rings, every 15 ft., in the same way as the tile.

Jan 1, 1921

By Michael A. Toole, O&apos

INTRODUCTION The tremendous capital investment required to produce a low grade ore deposit demands a reliable answer to the question: "How much does it cost to drill a well to produce the uranium that geologists have indicated is there in the ground?" However, you will find the answers given will be many and varied, depending on whether they come from the operating company, the drilling contractor, a geologist, a reservoir engineer, purchasing agent, or whoever. Each generally considers only a limited area of the total operation. The operating company usually depends upon the drilling contractors, service companies, and consultants to supply expertise. Because it is often difficult to see the "whole picture" or even to agree upon what the "whole picture" is, planning a well program and its costs is often done piecemeal. Frequently, costs "saved" in one area of the program are needlessly spent in another, because the effect of one area upon the other was overlooked. Since the drilling fluid is such an influential part of the drilling program, it should be given utmost consideration when planning the overall program. As W. D. Lacabanne wrote in 1954: "The drilling fluid system is understandably called the heart of the rotary oil drilling rig. Any other type of rotary rig.... should benefit by the incorporation of mud fluids in the drilling scheme." And G. R. Gray mentions that "The driller recognizes the drilling fluid as one of the useful tools available to solve drilling problems." However, in minerals drilling, only in recent years has the drilling fluid been considered as more than a tool to get through special problem areas. Although there are many similarities between drilling for oil and gas and drilling for minerals, the differences in the drilling equipment used justifies designing specific fluids for the minerals drilling industry. NL Baroid/NL Industries, Inc. has been a leader in introducing such fluids and in providing technical know-how to the minerals drilling industry. The purpose of this paper is: (1) to discuss the selection of drilling fluids to meet specific drilling conditions during both exploration and production and (2) to show the interrelationship among factors present in the exploration and production phases that influence total well costs. DRILLING FLUIDS FOR DRILLING PROBLEMS The drilling fluid is a tool that can be used to improve drilling performance by improving hole cutting, cleaning, stability, and formation productivity. Properly formulated and maintained drilling fluids enable the drilling operation to be carried out with increased efficiency and lower total (overall) costs. However, it should be noted that not all drilling problems can be solved by even the most carefully prepared and maintained drilling fluids. Of the many possible drilling problems encountered in a well before reaching target depth, this paper will discuss only those most likely to be present in the shallow [61 to 610 m (200 to 2000 ft)] drilling operations in South Texas. LOST CIRCULATION Loss of circulation is the most common problem encountered in drilling. Because the losses occur under varied conditions, it is often difficult to determine the exact causes. "Lost circulation" or "lost returns" means the partial or complete loss of drilling fluid to voids in the formation. "Loss of water" while drilling with water may take place into any permeable section and should be distinguished from "water loss" or filtration of fluid through the filter cake of mud solids laid down on a permeable formation. "Loss of water" can frequently be stopped by the addition of colloidal sized clay particles such as high yield bentonites, whereas "water loss" may be controlled with organic polymers. Subsurface conditions that lead to loss of circulation can be classified as: (1) natural fractures, (2) induced fractures, (3) unconsolidated or highly permeable formations (loose gravel), and (4) cavernous formations (crevices and channels). Loss of circulation may occur whenever the borehole pressure exceeds the formation pressure. The greater the differential pressure, the more likely it is that circulation may be lost. To stop loss of whole mud, voids must be bridged so that a filter cake can be laid down on the permeable section. The plugging material must be of the proper size and shape to offer greater resistance to the fluid flow around it than the flow up the annulus. A plugging composition that satisfies these requirements may not be able to be handled by the small rig pump available.

Jan 1, 1979

By A. A. Janke, G. J. Vogel, W. M. Swift

The combustion of fossil fuels in a fluidized bed of calcined limestone particles is a potentially efficient and economically attractive process for the generation of steam for electric power production and other uses. The process results in greatly reduced emissions of both sulfur oxide and nitrogen oxide pollutants. Development work, evaluations, and design studies are being carried out by various organizations under contract with the Department of Interior (Office of Coal Research, OCR) and with the U.S. Environmental Protection Agency, (EPA). The Atomic Energy Commission's Argonne National Laboratory is one of the principal participants in the development program under interagency agreements with EPA and OCR. The principal reasons for developing fluidized-bed combustion, its advantages and disadvantages over conventional combustion methods, and some of the potential applications of the process are covered in this paper. The participants in the multiorganizational program, the sponsoring agencies, the general status of development of the overall project, and the chief program areas that still require resolution are discussed. The main features of the program of work at Argonne National Laboratory and the results achieved so far are also included.

Jan 1, 1976

By A. E. Wheeler, H. Y. Eagle

The copper industry in the Province of Katanga, in the Belgian Congo, which is now controlled and operated by the Union Minére du Haut Katanga, had its inception many years ago in the vision of a Scotsman, Robert Williams, now Sir Robert Williams, Baronet. He it was who personally negotiated the mineral concession with King Leopold of Belgium, sent in the prospecting parties who located most of the present mines of the company, later arranged for the Belgian participation from which the present company was formed, and has been its active mentor ever since. The idea back of his efforts was the establishment of an industry on the Congo-Zambezi divide, of sufficient importance to draw up to it the head of the Cape to Cairo Railroad, the dream of Sir Cecil Rhodes, and the consummation of which he had left as a legacy to Mr. Williams, his successor. The reports of the prospecting expeditions showed that copper in profitable quantity was there, but many difficulties lay in the way of the establishment of the infant industry. The isolated location of the mines, various tribal wars, the Boer War, and many other factors contributed to making progress very slow. However, in spite of these difficulties the railroad was finally built and a blast-furnace plant erected at Lubumbashi, near Elisabethville, the capital of the Province. Operations of this plant were started in 1911, treating high-grade oxidized ores and producing pig copper by a reducing smelting. Production has been continuous since that time and the company has grown so that at present it ranks as the largest individual copper producer in the industry. It is a fitting monument to the foresight, optimism and driving force of its founder, and the progressive policies of his Belgian colleagues. In January, 1914, the Union Miniere du Haut Katanga engaged as its consulting engineer, Archer E. Wheeler, metallurgical engineer, at that time general superintendent of the Great Falls plant of the Anaconda Copper Mining Co. Mr. Wheeler was commissioned by the Board of Directors to proceed into Katanga, and make all necessary investigations to enable him to report on a comprehensive development program, and to recommend a scheme of treatment particularly for their low grade

Jan 1, 1934

By Nathan C. Rockwood

LIME is a very general term applied to products of limestone, in popular treatises often incorrectly, including ground or pulverized limestone used in agriculture. When used without qualifying adjective, the term usually means burned or calcined limestone, or quicklime, or calcia. The corresponding calcined product of magnesite is magnesia. If the calcined rock is relatively pure calcium carbonate, the resulting lime is a "high-calcium" lime; if the rock is dolomite, or a combination of calcium and magnesium carbonates, the lime is a "dolomitic" or a "high- magnesium" lime. There are various grades in between, depending on the percentage of magnesium carbonate and other ingredients in the raw rock. For some industrial purposes only high-calcium limes are suitable; in other processing-as, for example, neutralizing acid wastes -the relative percentages of magnesium and calcium carbonates in the raw material are not important. Limestone is burned (roasted or calcined) in furnaces known as lime kilns by direct exposure to the hot gases and flames. When heated to incandescence, the carbon dioxide content of the rock is expelled, leaving calcium and magnesium oxides, according to the formula usually written: [ ] This thermal reaction is reversible, which requires that the lime be withdrawn from the "calcining zone" of the kiln about as fast as made. Pure calcium carbonate would lose 44 pct of its weight in the calcining process; dolomite, 48 pct. Generally, the lime will retain the approximate size and shape of the piece of rock from which it is made but some few limestones tend to break down into granules or dust. Hence lime (quicklime) comes from the kilns in lumps or granules and normally is packed in water- tight containers in these forms, or is pulverized after calcination.

Jan 1, 1949

By Clarence Zener

IT is customary to regard the stress-strain relation as consisting of two parts, the elastic region and the plastic region. The essential attribute of the plastic region is the presence of a permanent set, which remains upon removal of all stresses. The essential attribute of the elastic region is the absence of such a permanent set. Absence of a permanent set does not imply a linear relation between stress and strain, nor even a single valued relation. In fact, in no real metal is stress a single valued function of strain in the elastic region. The property of a solid in virtue of which stress and strain are not uniquely related in the elastic range will be called "anelasticity." The purpose of the present article is to review and correlate the past work upon the anelasticity of metals. The following paper by W. A. West124 describes investigations upon anelastic properties of iron. Many manifestations of anelasticity have been observed, the first as early as 1835 by Weber.1,2 In his experiments Weber subjected a specimen to a constant load (or deformation) for a given time, and then suddenly removed the load. He observed that most of the deformation suddenly disappeared, but that there remained a residual deformation, which disappeared only gradually with time, as is illustrated in Fig. I. The occurrence of a residual deformation which only gradually disappeared, Weber called the elastic after-effect (Elastische Nackwirkung). An extensive review of the early work upon elastic after-effects has been given by Auerbach.3 Another manifestation of anelasticity is the dependence of the elastic constants-e.g., Young's modulus upon the method of measurement. Thus, if dynamic methods are used, the measured value will depend upon the frequency of oscillation. Still another manifestation is dissipation of energy attending vibration, called damping or internal friction. One objective of metallurgical science is the understanding of the plastic and fracture properties of metals in terms of their microstructure. Through such an understanding will come the ability to design microstructure to give the desired mechanical properties. A study of an elasticity will furnish an invaluable aid in the attainment of this objective. Such studies, when properly guided, yield information regarding the relation between stress and strain in the individual components of the microstructure. In order, however, that this type of information may be obtained, it is necessary that the experimental studies of anelasticity be interpreted by the appropriate mathematical analysis. This article, therefore, starts with the mathematical formulation of anelasticity.

Jan 1, 1946

By R. J. Piros, Brusenback, D. A. Dahlstrom

DEWATERING fine coal has been a serious problem to many operators who desired to wet-wash finer sizes and maintain high recovery. Centrifugal driers have become popular for this purpose for sizes between 3/8 in. and 14 mesh. Below 14 mesh the perforated screen centrifuges lose a large per- cent in the effluent solid bowl types that do retain -14 mesh coal, produce excessive degradation, tend to retain the highest ash fraction in any size fraction, and are subject to abrasion, which results in higher maintenance. In 1949 Truax-Traer Coal Co. planned a cyclone installation at their Ceredo preparation plant to recover coal down to 150 mesh with approximately a 14-mesh top size. Since available centrifugal equipment was not considered satisfactory, an investigation of rotary vacuum filters was begun in cooperation with the Peterson Filters and Engineering Co. to determine the suitability of the Peterson Top Feed Reservoir (TFR) filter. This investigation, which is described below, has resulted in a highly satisfactory installation of two 6x10-in. Peterson TFR filters that have been in operation over a year. After some preliminary laboratory batch vacuum filter tests, a pilot plant double-drum Peterson TFR filter was installed at Ceredo to prove the feasibility of vacuum filtration and determine optimum conditions. The full scale units were then installed on the basis of the pilot plant results. This was followed by an extensive research program on vacuum filtration in the laboratory at Northwestern University to investigate basic design and operating variables and their influence on final moisture con- tent of the filter cake. A method of scale-up from laboratory batch tests to the full-size unit was also proposed and proved. Because of the importance of dewatering fine coal today, it was felt that the results of the three steps should be made available for the use of others facing this problem. The work at Northwestern is given in a theoretical section following the discussion of the pilot plant and full- scale operation. Fig. 1 is a flow diagram of the cyclone and filter installation. The feed is drawn from below the

Jan 1, 1952

By H. I. Aaronson, H. A. Domian

The self-diffusivity of Ag10 has been measured as a function of temperature and composition in AgMg. a CsCl-type intermetallic compound with a substitutional defect structure on both sides of the stoichiometric (50 at. pct Mg) composition. These measurements show that In D increases linearly, and both In Do and Q decrease linearly with deviation from stoichiometry. The slopes of these lines are significantly steeper in magnesium-rich alloys. Equations for the variation of Q with composition have been derived by application of the theory of random walk processes on the assumption that diffusion in compounds of this type takes place by the six-jump cycle mechanism of Huntington, Elcock, and McCombie. The favorable agreement obtained with experiment furnishes fresh support for the correctness of this assumption. A principal result of this treatment is that. although the concentration of vacancies is considerably higher in the silver sublattice than in the magnesium sublattice, the acfivation energies for movement of the magnesium sublattice vacancies are so much lower that these vacancies are responsible for effectively all diffusion of silver in this compound. A tendency for vacancies of both types to be kinetically bound to wrong atoms is also noted. THIS study was undertaken to examine the influence of substitutional defects upon self-diffusion in an intermetallic compound, AgMg, with a CsCl-type crystal structure. The CsCl structure is exception- ally simple. At the equiatomic or stoichiometric composition in a binary alloy, it consists of two interpenetrating simple cubic sublattices, each of which is exclusively populated by the atoms of one species. When atomic size and other factors are favorable, deviations from stoichiometry can be entirely accommodated by the substitution of atoms of the species present in excess of 50 at. pct on the sublattice of the other species on a one-for-one basis. Under this condition, the only vacancies present are those formed by thermal activation. The excess atoms thus incorporated into the sublattice of the minority species may be considered as substitutional defects in this sublattice. Several X-ray studies have shown that the defect structure of AgMg is entirely of the substitutional type on both sides of the stoichiometric composition.1"3 The thermodynamic investigation of Kachi indicates that, aside from a low level of thermal disorder and these constitutional defects, order is maintained to the solidus temperature. This compound is therefore a particularly useful vehicle for a study of the influence of substitutional defects upon diffusion kinetics. Other advantages of AgMg for this purpose include: the broad composition region, as much as approximately 10 at. pct on either side of the stoichiometric (50 at. pct Mg), in which the compound is stable; the comparatively low temperature range of the solidus (820°C and below),5 making diffusion anneals near this range experimentally convenient; the reasonably good machinability of the compound, permitting utilization of the standard sectioning method of radiotracer analysis; and the availability of a good tracer, A for one of the constituent species. While this investigation was in progress, Hagel and westbrooks reported data on the self-diffusion

Jan 1, 1964

As bizarre an example of competitive salesmanship to be imagined took place last June in Western Australia. A half dozen world renowned mining groups received a Japanese iron and steel investigatory mission. Geologists, engineers and businessmen, all specialists in iron ore, representing elements of the Japanese government and steelmakers, politely grilled each iron ore group for technical information and plans for property development. At stake were sales contracts with Japan for many millions of tons of iron ore. Since approximately two dozen visitors were involved, it was necessary to divide them into four groups for dispensing information, transportation and accommodations at the remote exploration camps. In a continent noted for its wide open spaces, the hinterland of Western Australia is spectacularly lacking in settlements. The state has better than one third of Australian land and statistically 0.8 persons per sq mile. In reality, however, over 400,000 of the 800,000 population reside in Perth. Under such circumstances, properly receiving and feting these important visitors would seem to be difficult but the competing exploration groups vied ingeniously to outdo each other in hospitality.

Jan 10, 1964

By Keith Sutherland

AEROFLOAT 25 is a complex mixture of free cresylic acid with aryl substituted dithiophosphoric acids, sulphides, disulphides, etc. Its complete composition has not been published by the makers or patentees. It is prepared1 by the reaction between phosphorus pentasulphide and carefully selected cresylic acid. We have been informed that this acid contains no phenol and very little cresol, and that it is rich in the higher alkyl phenols, particularly the xylenols. The reaction between a phenol ROH and phosphorus pentasulphide may produce compounds of the following type:2 (i) RO S P Diaryldithiophosphoric acids RO SH (ii) R-SH Thiophenolic compounds (iii) R-S-R Diaryl sulphides (iv) R-S-S-R Diaryl disulphides (v) Substituted thianthren compounds Except for the simplest type, the thiophenols (ii), the boiling points of these compounds lie above 300° C. The amounts of the thianthren compounds formed from the five xylenols (if all these are present) will vary according to the position of the substituents. In an attempt to ascertain something of the nature of the reagent, fractional distillation under atmospheric pressure was undertaken. At the outset, hydrogen sulphide was freely evolved, and-particularly below 200° C.-the fractions had the strong odor characteristic of the

Jan 1, 1939

By Elbert Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

By A. S. Michaels, R. S. Timmins

A study of the effect upon oil recovery from an un-consolidated porous medium of chromatographic transport of selected reverse-wetting additives during water displacement is described. Flow tests were performed on hydrocarbon oil-saturated sand columns (containing connate water) into which small volumes of short-chain aliphatic amine solutions were introduced during water flooding. Concurrently, meusurements of oil-silica contact angles, oil-water interfacial tensions and oil-water distribution coefficients were measured us a function of additive concentration. Certain treatments were found to cause a slight reduction in oil recovery, while others produced a significant increase (up to 50 per cent of the normtzl irreducible rninimum oil saturation). Recovery eficiency was correlated most satisfactorily with the maximum degree of reverse wetting produced during additive transport; conditions which resulted in only mild oil wettability of the sand reduced recovery, while those favoring strong oil wetting increased recovery. A mechanism of reverse-wetting additive action during chromatographic transport is developed which ascribes the results to transient changes in oil-solid contact angle during flow, with consequent release of oil trapped by capillary forces. Implications of these observations with regard to improved waterflood efficiencies are discussed. INTRODUCTION The need for finding improved methods of oil production is amply illustrated by the large volume of oil considered economically unrecoverable by existing production practice. Water flooding has long been an excellent method of secondary recovery. However, even in those areas of a formation which are well swept by a water flood, 20 per cent or more of the oil remains trapped within the formation and is not recovered. This trapping of oil within the pores of the rock structure results primarily from interfacial forces. If these interfacial forces were altered, it is possible that the trapped oil could be released and recovered. The addition of surface-active agents to a water flood to alter the interfacial properties of the oil-water-solid system has received considerable attention as a method of increasing oil recovery. Studies of surfactant treatment have yielded varied and, in some cases, apparently conflicting results. Increased oil recovery using surface-active agents has been reported by a number of investigators. Others have found that use of surfactants in a water flood either has no effect upon oil recovery or decreases it. Since surface-active agents tend to alter the formation wettability and oil-water interfacial tension simultaneously, several investigators have tried to determine the role these two factors play in oil recovery. Data have been presented which indicate that the most desirable condition for the solid surface is strongly water-wet. Other results indicate that, although breakthrough recovery may be less, the greatest ultimate recovery is obtained when neutral wettability prevails.", " The desirability of low interfacial tension seems to depend upon the wettability of the formation. Reports of higher recoveries, when the interfacial tension is high in a water-wet system and low in an oil-wet system, are at odds with reports of increased recovery in water-wet systems when surfactants which decrease the interfacial tension are added to the water flood. A review of previous work studying the effects of using surface-active agents in a water flood shows that these agents produce widely different effects and that opinions as to the role of the various interfacial properties are diverse. The consensus, however, is that the interfacial properties are quite important in the displacement of oil from a porous medium by water. Even in those investigations where appreciable increases in oil recovery resulted from treatment with a surface-active agent, economic considerations generally made practical application of the treatment unattractive because surfactants tend to be adsorbed within the formation. This adsorption would necessitate using large quantities of surfactant if all of the flood water were treated to contain a given surfactant concentration, even if this concentration were quite low. Preston and Calhoun suggested that the principles of chromatography could be applied to the use of surface-active agents as a means of increasing oil recovery. A small volume of surface-active material is injec-

By M. L. Samuels

DURING the period from 1910 to 1920, there was a lively interest in the subject of grain growth and many papers were published, followed by interesting discussions. Questions dealing with the fundamentals of grain growth-why and how it occurs-were treated in papers by Howe,1 Jeffries,2 Sauveur,3 Chappell,4 Beilby,5 Mathewson and Phillips,6 McAdam,7 Carpenter and Elam,8 Stead and Carpenter,9 Ruder,10 as well as others. Since that decade, much indeed has been done regarding the practical control of grain size, and it is now possible to order material having a size specified in the American Society for Testing Materials classification. Also, one hears the term "spliced boundaries" used in connection with certain tungsten lamp filaments" wherein it is important to prevent "sagging" between consecutive turns of the helix." This practical use of a certain knowledge as to the things that influence or even control grain growth should not be taken as an indication that the subject has been thoroughly explored and that nothing more can be learned from fundamental studies. It is with this thought in mind that a report of some observations and experiments on abnormal grain growth is believed justified. Abnormal grain growth is met with in heat-treating high-carbon steels in the austenitic range,13 in the hardening treatments of high-speed steels, 14.11 and in the low-temperature annealing of strained low-carbon steels as in sheet and wire material. Entirely aside from these instances of exaggerated grain growth, which some might consider as freakish, it is thought that abnormal growth is simply a case where the growth forces and the forces tending to prevent growth are almost, but not quite, evenly balanced. Information relative to grain-growth characteristics in general may be obtained from a study of abnormal growth conditions, which may be looked upon as vantage points. Reflection will show at once that if growth forces are great in comparison to inertia or resistance to growth, many crystals start to grow and, for that reason, none becomes very large, whereas if inertia is predominant no growth at all takes place. Under conditions in which

Jan 1, 1938

By S. J. Green, R. D. Perkins

Little data exists on the high strain rate behavior of geologic materials. Uniaxial stress tests by Kumar1 and by Serdengecti and Boozer2 present some results to strain rates in the range 10 to 103 per sec. The two references cited are the only ones the authors found for high strain rates. Techniques for experiments at high strain rates are not well developed and, in general, leave questions with respect to interpretation of data when the material behaves in a brittle manner. The most reliable data at very high strain rates (104 to 106 per sec) are found in some recent flat-plate work3-5 where experimenters have impacted one plate into another, thereby creating a uniaxial strain loading. The standard uniaxial stress-strain curves cannot be obtained directly from these tests; however, yield (or fracture) may be studied by measuring the "elastic" wave magnitude. These data then may be compared to uniaxial stress data by resorting to some preassumed yield/fracture criteria. Even with the most liberal interpretation of existing data, little can be said of the effects of high strain rate on stiffness, yield/fracture, and post-fracture behavior of geologic materials. It is the purpose of this work to begin to add to the understanding. The data presented here are intended to provide material information for use in calculating the response of geologic materials to high rate deformations. These data can be applied directly to determine parameters such as the elastic modulus and Poisson ratio as a function of stress. Furthermore, these data can be used to derive an understanding of yield/fracture and the effect of rate on the yield/fracture surface. The work presented is a first step, and is

Jan 1, 1972