Search Documents

By W. H. Herrnstein, J. B. Clark, E. C. Utley, A. J. McEvily

The ratio of the endurance limit (10' cycles) to tensile strength of age-hardened aluminum alloys is approximately 0.3, whereas the ratio for annealed alloys is about 0.5. The lower value for the age-hardened alloys has been associated with the instability of coherent precipitate during cyclic loading, but it has not been definitely established whether this instability is due to overaging or reversion during cyclic loading. The results of the present investigatzon support the reversion viewpoint. In this work specimem of 2024-T4 aluminum alloy were aged for 16 hr at 150°C after cycling for 10 pct of the life at 25.000 psi. These specimens were then tested to failure and exhibzted a marked increase in fatigue life. It is proposed that during the early stages of fatigue in this alloy dislocations cut through the coherent precipitate and bring about the reversion of the precipitate. Subsequent aging at 150ºC induces reprecipitation in the precipitate-free zones so that the weakened regions are strengthened and the fatigue life is extended. It Is recognized that the fatigue strengths of precipitation hardened aluminum alloys are unusually low relative to their tensile strength.'-= This feature is illustrated in Fig. 1 where it can be seen that age-hardened alloys have lower fatigue ratios (the ratio of the fatigue strength to the tensile strength) than those in the annealed or cold worked state. Further, as shown in Fig. 2, the more an alloy is dependent upon precipitation hardening for its total strength, the lower is the ratio of the fatigue strength to the tensile strength. This state of affairs has been associated with an instability of the metastable metallurgical structure of precipitation hardened aluminum alloys during cyclic loading. Evidence2 in support of this view is that the fatigue ratio increases in these alloys as the test temperature is lowered, thereby indicating that thermo-mechanical instability, rather than some other factor such as a non-uniform distribution of precipitate, is the factor responsible for the low fatigue ratio at room temperature. Two mutually exclusive proposals have been ad- vanced to account for this instability. Hanstock has proposed that overaging takes place during cyclic loading, and in support of this view, Broom et a1.2 have indicated that an overaging process might be promoted by the large numbers of vacancies which are created during cyclic loading. The creation of vacancies by radiation4 has been shown to lead to rapid overaging. Hanstockl obtained visual evidence of overaging in an aluminum alloy after cyclic loading, but in this instance it has been pointed ou? that because of the high frequency used (60,000 cpm) the observed effect may have been due to normal high temperature precipitation around energy dissipating cracks. Efforts to discern visual evidence of overaging in this alloy at lower test frequencies were not successful.3 The alternative postulate3 is that reversion takes place during cyclic loading and leads to localized soft spots at which fatigue cracks are readily initiated. Evidence for this process has recently been provided by Polmear and Bainbridge5 who demonstrated metallographically that regions depleted of precipitate were created during cyclic loading of an aluminum alloy. Inasmuch as precipitate particles bordering the depleted region had not grown in size, it was concluded that the solute atoms which had constituted the missing particles had gone back into solution. No mechanism for the reversion process was presented. The present study was undertaken to investigate further the conditions leading to instability during cyclic loading, and to determine whether reversion or overaging had taken place as a result of cyclic loading. BACKGROUND AND TEST PROCEDURE In order to differentiate between the processes of reversion and overaging, rest periods at an elevated temperature, which ordinarily would insure additional precipitation, were used in this investigation. It was expected that after a period of cyclic loading an elevated temperature rest period would result in a decrease in the remaining life of the specimen if overaging were occurring during cyclic loading, whereas in the case of reversion, reprecipitation would occur and the fatigue life would be extended. Such an expectation is based on the assumption that the crack-nucleation phase is a significant portion of the total fatigue life, and that such a treatment is of influence in the crack-nucleation stage and is relatively unimportant thereafter.

Jan 1, 1963

THE CHAIRMAN (H. W. MORSE, Los Angeles, Cal.).-I would like to open this meeting for a little while to the general subject of leaching. We ought not to hold back if we have any new schemes for the future. I know that those of us who are tangled up with this lei thing work will appreciate any suggestions that will make us work harder and, scheme, harder to pull through these past difficulties on leaching. F. S. SCHIMERKA, Clifton, Ariz.-Under the direction of J. W. Bennie, General Manager of the Shannon Copper Co., Clifton, Ariz., 'it has been my valued privilege to cooperate in the elaboration of a hydrometallurgical process aiming at the recovery of copper in mill tailing resulting from a gravity concentration of a low-grade semi-oxidized sulphide ore occurring in a porphyritic gangue. The experimental work which has been carried on with a 25-ton plant is completed, and the company is building at present a leaching plant on a larger scale, the first unit consisting of a 150-ton roasting furnace and accessories for leaching the calcine.

Jan 12, 1916

By G.A. Moore, C. E. Sims

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By C. E. Sims, G. A. Moore

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

Herewith are transmitted the joint report of the Treasurer and Finance Committee for 1934 and the reports for the same year of the Chairmen of the following Committees: Admissions, Membership, Papers and Publications, Library, and MINING AND METALLURGY. TO these reports you are referred for details of the year's activities. Finances.-Income for 1934 from all sources totalled $134,967 com- pared with $121,689 in 1933. The increase is accounted for principally by four items: $6000 increase in initiation fees and dues of new members; $1800 in current dues; $4000 in "back" dues; and $2800 in the sale of publications, including TRANSACTIONS volumes and technical papers in the form of "separates." In passing, it may be remarked that income from back dues during 1935 will be less than in 1934, for the obvious reason that the total amount of dues in arrears has shrunk and consequently there is less to draw from. Income from

Jan 1, 1934

By James W. Neill

Discussion of the paper of H. 0. Hofman, presented at the Canal Zone meeting, November, 1910, and printed in Bulletin No. 42, June, 1910, pp. 473 to 497. JAMES W. NEILL, Pasadena, Cal. (communication to the Secretary *) :-Professor Hofman's paper brings the art up to . date. As I was one of the pioneers in this business, I beg to give the following incomplete data regarding my efforts in this line. In the year 1883, while I was in charge of the smelting-operations at Mine La Motte, Mo., there was at the concentrator an unusually large production of a middle product, locally called "iron," which carried considerable values in nickel and cobalt, and which it was desirable, for this reason, to treat by itself. The works could not spare a furnace for the purpose; and to handle this product I improvised a "roast-hearth " from an old " lead-hearth." This was a small cast-iron furnace of the usual construction, about 2 by 4 ft. in dimensions, with a hollow cast-iron back, through which the wind circulated before entering the tuyeres. I had a cast-iron grate made to fit this hearth, and placed it flush with the lip, or apron, and above the tuyeres. On this grate, which had round holes about 0.25 in. in diameter, and a total surface of about 20 by 40 in., I roasted the nickeliferous pyrite product; starting the fire with kindling, then adding charcoal, and then gradually feeding the sulphides with a shovel, so as to cover the fire, choke down blow-holes, and get an even bed. Blast at a pressure of 3 or 4 oz. was supplied by a fail-blower. When a cake of roasted material had formed, it was removed with a steel bar, or fork, to the lip of the furnace, and thence into a wheel-barrow.. The fine material which had remained unmelted, but very hot, on top of the cake would promptly ignite when the cake was broken up and removed. The fire would then be covered with fresh material and * Received Aug. 29, 1910.

Apr 1, 1911

By Newell G. Alford

Forecasts of future timber consumption in soft-coal mining are handicapped by the lack of adequate experience records for estimating properly the timber requirements of the industry. Data were obtained from plants where records are kept or from operators who collected the information and to these were added composite figures for the continental United States in 1905 and 19191 and for central and western Pennsylvania and for Illinois in 1922.2 The result, representing slightly over 928,000,000 net tons, is shown in Table 1. Some of the companies furnishing data were unable to segregate the timber into classes of use but for those who did, Table 2 shows the board feet of posts and cross ban used per ton of coal mined and the percentage of the total timber consumed that was used in roof support. The wide variation in amounts of timber per ton of coal mined is the result of

Jan 1, 1924

By Parviz Montazer, Robert King, William Ubbes, Gideon Chitombo

This paper describes the results of a detailed study that was undertaken to define the spatial distribution of permeability within a five meter thick envelope around the CSM/ONWI room. Detailed fracture orientations and distribution were determined through mapping of the walls of the opening, logging of oriented core, and visual examination of borehole walls with a borescope and a T.V. camera. Over 3,500 measurements were made from which the three dimensional distribution of fractures was determined. Two principally different testing equipment designs and various methods of air injection tests were used in all boreholes to identify and characterize conductive fractures. Through analizing the distribution of permeability and fracture index around the room a zone of blast damage of approximately .5 m thickness was delineated. The effect of stress modification seems to extend farther into the host rock to approximately 3.5 m depth.

Jan 1, 1982

By Thomas Harris

This paper. was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the' reduction of indivi-dual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States. in order to consolidate the information de-veloped from the many hundreds of boiler tests on coals consumed by various coal¬burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal date, including description of coals used (with. sufficient space to- include first, second and third, preference) on--source of coal used,- complete-analysis and factors affecting choice of, coal used. 3. Plant data, divided into - A. Hand fired, B. Overfeed stokers,. . C. Underfeed stokers, D. Traveling grate stokers, E. Pulverized coal, and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency date and remarks.

Jan 1, 1933

By William B Price, Ralph W. Bailey

Arsenic, antimony and phosphorus are now used in the brass industry as standard inhibitors in preventing dezincification in condenser tubes. This subject has been thoroughly covered by Barry,l who de- scribed the testing procedure by total immersion of suitable specimens in a I per cent cupric chloride solution at definite temperatures. Effects of dezincification were then determined by loss in tensile strength and elongation of the test specimens after definite periods of immersion. In the crystallography of the chemical elements as tabulated by William Hume-Rothery,2 phosphorus (metallic), arsenic, antimony and bismuth are placed in group V-B and the type of crystal lattice for arsenic, antimony and bismuth is given as rhombohedral. The Metals Handbook3 lists them as 'rhobomhedral hexagonal," with the additional notation that for arsenic this is the ordinary form at 20°C.; other modifications known or probable at other temperatures. In view of these statements and of the fact that phosphorus, arsenic and antimony are effective in increasing the resistance to dezincification, it was natural to assume that bismuth would act in the same manner. A series of tests was therefore carried out employing the methods described by Barry. Much to our surprise, bismuth did not inhibit dezincification, but rather seemed to accelerate it. Tensile-test speci-

Jan 1, 1942

By Ralph W. Bailey, William B. Price

Arsenic, antimony and phosphorus are now used in the brass industry as standard inhibitors in preventing dezincification in condenser tubes. This subject has been thoroughly covered by Barry,l who de- scribed the testing procedure by total immersion of suitable specimens in a I per cent cupric chloride solution at definite temperatures. Effects of dezincification were then determined by loss in tensile strength and elongation of the test specimens after definite periods of immersion. In the crystallography of the chemical elements as tabulated by William Hume-Rothery,2 phosphorus (metallic), arsenic, antimony and bismuth are placed in group V-B and the type of crystal lattice for arsenic, antimony and bismuth is given as rhombohedral. The Metals Handbook3 lists them as 'rhobomhedral hexagonal," with the additional notation that for arsenic this is the ordinary form at 20°C.; other modifications known or probable at other temperatures. In view of these statements and of the fact that phosphorus, arsenic and antimony are effective in increasing the resistance to dezincification, it was natural to assume that bismuth would act in the same manner. A series of tests was therefore carried out employing the methods described by Barry. Much to our surprise, bismuth did not inhibit dezincification, but rather seemed to accelerate it. Tensile-test speci-

Jan 1, 1942

By W. B. Daly, A. S. Richardson

The application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable. The Ventilating Problem at Butte The main obstacle to satisfactory ventilation in the Butte mines is the normally high temperature of the granite country rock. In the present operating zone, rock temperatures as high as 120' F. have been noted, and in some parts of the district the rate of increase of temperature with depth has ranged as high as 3.5" F. per 100 ft. Other factors, such as the decay of mine timber and the oxidation of sulfide minerals in the ore bodies, contribute to raise the temperature of the air in the working places but, particularly in the development of the mines to greater depth, the naturally high temperature of the rock is of predominant importance. In few other places, probably, are the ordinary ventilating measures more hindered than at Butte. At an operating depth now exceeding 3000 ft., all of the air required for ventilation must pass through timbered shafts which, because of heavy ground, are of small size and offer great resistance to the flow of air. Shaft compartments are rarely more than 4.5 X 5 ft., and the shaft area open to the flow of air usually does not exceed 65 sq. ft.; in only two shafts is the area as great as 85 sq. feet.

Jan 1, 1934

By James D. McClung, H. J. Gluskoter, M. R. Geer

INTRODUCTION The purpose of coal preparation is to improve the quality of coal to make it suitable for a specific purpose by (1 ) cleaning to remove inorganic impurities; (2) sizing-crushing or screening, or both; or (3) special treatment, such as dedusting. The properties and quantities of impurities in coal are of major importance in the design and operation of steam generating equipment. Al- though boilers are often designed and equipped to use a wide range of coals, no boiler will perform equally well with all types of coals. All coals have certain properties that place limitations on their most advantageous use. These limitations are especially stringent for many of the older installations. Because of a general lowering of quality of raw coal in recent years, the need for coal cleaning has significantly increased. Among the factors contributing to the need for increased coal preparation are (1) increased demand for quality brought on by market and environmental requirements; (2) increased extraneous dilution caused by mine, health, and safety laws; and (3) depletion of the higher-quality coal seams.

Jan 1, 1979

The Committee submits the following report: The General Committee met in the Treasury Building at Washington on Oct. 6 and 7, 1919. At the first meeting, Cornelius P. Kelley was appointed chairman, and Paul Armitage, secretary of the Committee. Subcommittees were appointed on Invested Capital, on Mine Valuation, and on Depletion and Depreciation. These subcommittees were directed to meet separately and to report on Oct. 7 to the General Committee. On Oct. 7, the reports of these committees were submitted to the General Committee and on motion were received and referred to the Executive Committee for its information to be used as it deemed wise. A motion was carried that the Executive Committee be constituted a permanent committee to continue the work of the Committee, with full power to add to and increase its membership; that as thus increased it should constitute a permanent organization to act and cooperate with the Treasury Department in matters of mining taxation under the Federal Income and Excess Profits Tax Laws. Thereafter the Executive Committee met and formed a permanent committee as follows: Cornelius F. Kelley, chairman, 42 Broadway, New York City. J. L. Darnell, Office of the Commissioner of Internal Revenue, Washington, D. C. J. Parke Channing, 61 Broadway, New York City. Walter Douglas, 99 John St. New York City. R. V. Norris, 542 Second National Bank Bldg., Wilkes-Barre, Pa. J. E. Spurr, care of Engineering & Mining Journal, 10th Ave. and 36th St., New York City. W. G. Swart, 808 Selwood Bldg., Duluth, Minn. J. P. Finley, 45 Cedar St., New York City. W. A. Williams, Bartlesville, Okla. F. S. Peabody, care of Peabody Coal Co., McCormick Building, Chicago, Ill. Matthew C. Fleming, 71 Broadway, New York City. H. B. Fernald, 54 Wall St., New York City.

Jan 1, 1923

The Committee submits the following report: The General Committee met in the Treasury Building at Washington on Oct. 6 and 7, 1919. At the first meeting, Cornelius P. Kelley was appointed chairman, and Paul Armitage, secretary of the Committee. Subcommittees were appointed on Invested Capital, on Mine Valuation, and on Depletion and Depreciation. These subcommittees were directed to meet separately and to report on Oct. 7 to the General Committee. On Oct. 7, the reports of these committees were submitted to the General Committee and on motion were received and referred to the Executive Committee for its information to be used as it deemed wise. A motion was carried that the Executive Committee be constituted a permanent committee to continue the work of the Committee, with full power to add to and increase its membership; that as thus increased it should constitute a permanent organization to act and cooperate with the Treasury Department in matters of mining taxation under the Federal Income and Excess Profits Tax Laws. Thereafter the Executive Committee met and formed a permanent committee as follows: Cornelius F. Kelley, chairman, 42 Broadway, New York City. J. L. Darnell, Office of the Commissioner of Internal Revenue, Washington, D. C. J. Parke Channing, 61 Broadway, New York City. Walter Douglas, 99 John St. New York City. R. V. Norris, 542 Second National Bank Bldg., Wilkes-Barre, Pa. J. E. Spurr, care of Engineering & Mining Journal, 10th Ave. and 36th St., New York City. W. G. Swart, 808 Selwood Bldg., Duluth, Minn. J. P. Finley, 45 Cedar St., New York City. W. A. Williams, Bartlesville, Okla. F. S. Peabody, care of Peabody Coal Co., McCormick Building, Chicago, Ill. Matthew C. Fleming, 71 Broadway, New York City. H. B. Fernald, 54 Wall St., New York City.

Jan 1, 1923

By Charles C. Russell, Glenn C. South

A primary factor in the selection of coals for making coke at high temperatures is the amount of pressure the coal will exert upon the oven walls when carbonized in modem by-product ovens.l-3 This factor has become increasingly important in recent years because of demands for increased throughput and higher coke yields. As a result of the increasing necessity for assessing coals in regard to their carbonization pressures, more and more research work is being directed toward developing labora-tory-scale tests for predicting carbonization pressures and for showing how blends of coking coals may be modified to eliminate pressures liable to damage coke-oven walls. The specific reasons have never been defined as to why some blends of coking coals develop dangerous carbonization pressures and others do not, therefore specific procedures to eliminate dangerous pressures could not be prescribed. It is true that the major processes occurring during carbonization have been described by many writers,4 and there is a general agreement on the ideas of the changes that occur as coal is transformed into coke. However, there is little evidence relating the processes occurring during carbonization to the pressure developed and the available evidence is very incomplete and often contradictory. This deficiency arises in part from the fact that the fundamental causes of pressure development have not been defined, at least from experimental data, and in turn this is the result of the lack of satisfactory testing equipment for studying the problem. Operating experience has shown several ways of reducing or eliminating dangerous pressures,5 but probably none of these ways is applicable to all blends of coking coals, and such empirical methods often lead to production of inferior coke. They are trial-and-error methods, not designed to remedy specific causes of pressure development. The number of laboratory-scale testing devices designed to estimate the carbonization pressures that result when coals are carbonized in commercial ovens is probably well over a hundred.6 Few of these instruments have remained in use for any length of time, either because the predictions were not sufficiently accurate or, more often, because too many exceptions were found. Often testing devices are operated without any attempt at duplication of conditions in commercial ovens and erroneous and contradictory results are frequently obtained. Therefore, it has seemed desirable to study the properties of coal itself and to determine any relationships between the properties of the coal and the carbonization pressures developed. Relationship between Properties of Coal and Carbonization Pressure Attempts to determine relationships between various properties of coal and carbonization pressures, for the most parti have been indirect because no satisfactory and reliable laboratory testing device has

Jan 1, 1944

By Glenn C. South, Charles C. Russell

A primary factor in the selection of coals for making coke at high temperatures is the amount of pressure the coal will exert upon the oven walls when carbonized in modem by-product ovens.l-3 This factor has become increasingly important in recent years because of demands for increased throughput and higher coke yields. As a result of the increasing necessity for assessing coals in regard to their carbonization pressures, more and more research work is being directed toward developing labora-tory-scale tests for predicting carbonization pressures and for showing how blends of coking coals may be modified to eliminate pressures liable to damage coke-oven walls. The specific reasons have never been defined as to why some blends of coking coals develop dangerous carbonization pressures and others do not, therefore specific procedures to eliminate dangerous pressures could not be prescribed. It is true that the major processes occurring during carbonization have been described by many writers,4 and there is a general agreement on the ideas of the changes that occur as coal is transformed into coke. However, there is little evidence relating the processes occurring during carbonization to the pressure developed and the available evidence is very incomplete and often contradictory. This deficiency arises in part from the fact that the fundamental causes of pressure development have not been defined, at least from experimental data, and in turn this is the result of the lack of satisfactory testing equipment for studying the problem. Operating experience has shown several ways of reducing or eliminating dangerous pressures,5 but probably none of these ways is applicable to all blends of coking coals, and such empirical methods often lead to production of inferior coke. They are trial-and-error methods, not designed to remedy specific causes of pressure development. The number of laboratory-scale testing devices designed to estimate the carbonization pressures that result when coals are carbonized in commercial ovens is probably well over a hundred.6 Few of these instruments have remained in use for any length of time, either because the predictions were not sufficiently accurate or, more often, because too many exceptions were found. Often testing devices are operated without any attempt at duplication of conditions in commercial ovens and erroneous and contradictory results are frequently obtained. Therefore, it has seemed desirable to study the properties of coal itself and to determine any relationships between the properties of the coal and the carbonization pressures developed. Relationship between Properties of Coal and Carbonization Pressure Attempts to determine relationships between various properties of coal and carbonization pressures, for the most parti have been indirect because no satisfactory and reliable laboratory testing device has

Jan 1, 1944

By R. S. Craig, W. E. Wallace, G. S. Kamath

The destruction of long-range order in Mg-Cd, has previously been thought to occur as a second order process. In the present work a variety of X-ray diffraction techniques are employed to show that in this case and in Mg-Cd alloys containing frorn 20 to 33 1/3 at. pct Mg the process more nearly resembles an ordinary first order phase transformation. It is found that the ordered alloy, which occurs as a single phase at lgw temperatures, transforms with increasing temperature into a Cd-enriched disordered (P) phase and an Mg-enriched ordered (a) phase. The interval over which these two phases coexist under apparently equilibrium conditiovs extends from 25" to 87°C content. At 33 1/3 at. pct Mg the two-phase region has disappeared. Measurement of the long range order parameter, s, for the ordered phase in MgCd, (from superlattice line intensities) shows that it disorders only very slightly before it is transformed into the p form. Kinetic experiments reveal that when the a phase is formed frorn the p phase by suitably quenching so as to suppress phase segregation, the transformation is essentially complete and the a phase has acquired its equilibrium value of S in less than 1 min. In an earlier investigation carried out in this Laboratory1 the rate of disordering of the MgCd3 superlattice was determined over an extensive range of temperature. The process was found to be first order and the rate constant, k, was established. At the lowest temperatures studied k was found to increase exponentially with temperature. At higher temperatures, however, it passed through a maximum and for the 100 deg interval below the point at which the superlattice was destroyed k was observed to decrease with increasing temperature. The various theoretical treatments1-3 of order-disorder phenomena lead to a negative temperature coefficient for k near the superlattice critical temperature but this region for MgCdB seemed unusually wide. Detailed analysis of the point indicated' that either the long-range order parameter, S, for MgCda varied with temperature in an anomalous way or the disordering in this instance is more complex than in the cases which have been treated theoretically. The original objective in the present work was simply to determine S vs temperature for MgCda to ascertain whether the disordering was in conformity with theoretical expectations.2° In an early stage of the work it was noted, however, that under equilibrium conditions ordered (a) and disordered (0) phases coexist in MgCd, over a considerable range of temperature. Since on thermo- dynamic grounds the coexisting phases must differ in composition, the investigation was enlarged to permit the compositions of the two phases in MgCd3 to be determined and to establish the extent of the two phase regions for alloys containing from 20 to 33 1/3 at. pct Cd.

Jan 1, 1963

Executive-A. R. Ledoux, chairman. Membership-J. V. W. REYNDERS, chairman. Finance-J. V. N. Dorr, chairman. Library-E. GYBBON SPILSBURY, chairman. Papers and Publications--BRADLEY STOUGHTON, chairman. Nominations-Pope YEATMAN, chairman.

Jan 11, 1919

By R. N. Upadhyay, M. Maleki, I. Fatt

Conventional laboratory core analysis tests on samples of two limestone reservoir rocks indicate that about 20 per cent of PV is in dead-end pores. These tests (electric logging formation factor, mercury injection capillary pressure and miscible displacement) were carried out on 1/4-in. diameter test plugs. Test results show a clear dilference between these samples and sandstone or homogeneous limestone reservoir rock. Although the amount of dead-end pore space can be only roughly estimated, the presence of such pore space seems clearly indicated. Pressure transient studies also show presence of deadend PV. Although they do not give quantitative results, pressure transient data yield a reasonable estimate of the size of the neck connecting dead-end pores to the main flow channels. INTRODUCTION Equations conventionally used to describe reservoir flow behavior contain the implicit assumption that all connected pore spaces contributed to both porosity and permeability. Several authors3-7 have pointed out the changes in pressure transient behavior and in electric log interpretation that may result if this assumption is incorrect and, instead, dead-end or cul-de-sac pores are present. There is a need for laboratory tests that can detect presence of dead-end pores in core samples. With such information on hand the petroleum engineer can make more rational use of the mathematical tools now available for analysis of reservoir flow behavior. This paper describes laboratory studies designed to detect and, if possible, give a quantitative measure of dead-end PV in laboratory-size core plugs. Three reservoir rocks were used, two of which were limestones suspected of having deadend pore spaces and a well-known sandstone, used as a comparison standard, in which there is believed to be little or no dead-end pore space. All the studies were designed to measure the natural dead-end PV; i.e., the pore space which is dead-ended because of rock structure. During multiphase flow in a rock without dead-end pores, some parts of one of the phases can become surrounded by the other, thereby giving (for certain flow behavior) an effective dead-end pV8,9. Such behavior will not be described here.

Jan 1, 1967