Search Documents

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

GENERAL GEOLOGICAL DESCRIPTION The uranium mineral appraisal herein described was made for an ore deposit in New Mexico. The uranium mineralization occurs as roughly tabular to lens-shaped deposits of varying thickness within the sandstone of the Jackpile formation of Jurassic age. The mineralization occurs at several horizons within the Jackpile formation, but is not always confined to specific beds. It often transgresses across stratigraphic layers, as demonstrated when attempting correlation of uranium gamma anomalies between adjacent drill holes. Preferred mineral trends have been established in some parts of the deposit, but are not always predictable when attempting to extrapolate beyond the zones defined by drill hole sampling. MANAGEMENT OF DRILL HOLE SAMPLE DATA All of the drill hole sample data used in the appraisal were obtained from interpretation of gamma-ray logs. A brief description of gamma-ray log sampling is given in Chapter 2. Two preliminary steps are involved in preparing gamma-ray logs into sample data normally acceptable for computer manipulation. 1) The gamma analog trace produced by the downhole probe must be digitized, i.e., counts-per-second (CPS) are recorded for each 0.15 m (1/2-ft) interval across the gamma-ray anomaly. The work is usually done on a "digitizer" while following the analog trace with an electronic stylus on a special tablet or table. The other alternative is to do the work manually. Some of the newest downhole logging equipment produces a magnetic tape output which can be read by a computer. 2) The gamma-ray CPS values must then be converted to equivalent U308 assay values, taking into consideration all appropriate correction factors. The US Atomic Energy Commission, now part of the Department of Energy, developed the theory and algorithm for this conversion in the 1960's, and though the work can be done manually, it is best done with the GAMRED (gamma-reduction) computer program. Fig. 14-1 illustrates a typical analog trace produced by the probe instrumentation, including gamma-ray trace (left), self-potential electric log (center), and resistivity log (right). Fig. 14-2 shows a form of the computer output after the analog data has been digitized to 0.15-m (1h-ft) intervals and converted to percentage U308 values for the same hole. The U308 grade bar graph on the right permits rapid visual inspection of anomalous values by depth and elevation. The converted U308 sample data were next processed by the SURVEY program that assigned to each assay interval [0. 15-m (1h-ft)] an X Y Z coordinate, taking into account all deviations indicated from downhole survey information. The output file of the SURVEY program was listed on the line printer for examination by project geologists, and also became the main input file for the URAN/ COMP compositing program, which is designed to group individual 0.15-m (/-ft) U308 sample values into larger intervals representing discrete anomalous zones according to a series of specified parameters entered into the program by the user. Composite U308 intervals were computed by the URAN/COMP computer program, the logic of which may be briefly described as follows: Step 1 The program searches for the highest U308 value in the hole and builds a composite by adding the highest grade interval on either side so long as the added value is greater than a minimum acceptable grade, and the total composite, after addition, meets minimum GT (grade times thickness) constraints. Step 2 The program loops back to find the next highest assay value in the hole not already included into a composite, until all anomalies above minimum cutoff grade are composited. Step 3 Individual composites are combined if they are closer than a specified minimum waste thickness, and the resultant composite grade still meets GT minimums.

Jan 1, 1980

By Clark B. Risler, Walter E. Thomas

MILL planning must include electrical drives and a system to supply them. These should be considered at the time metallurgical and mechanical plans are being made. Because it is convenient, flexible, reliable, and economical, electricity is the accepted source for powering mill concentrating equipment. Ore-treating mills have grown to the point where a single mill has been built using 360 motors ranging from 1 to 1000 hp and totaling 50,000 hp. Such a system of electrical drives can be scattered over a square mile and employ 4000 to 220 v. Drive Motor Characteristics: Since ore processing is predominantly a continuous operation, very few of its drives require wide speed variation after initial adjustment. Consequently squirrel cage, wound rotor, and synchronous alternating current motors are most often used.

Jan 5, 1957

By Kenneth Robertson

ALL, strangers visiting this district are struck with the peculiar manner in which the pig-iron is graded. There are eleven regular grades, besides which, when gray forge is ordered, one-half of Nos. 1 and 2 Mill are shipped. Occasionally there is another grade Known as Silver Mill, which is made so seldom that I cannot describe it, and have no sample to exhibit. Most of you have found it difficult to grade properly and uniformly under the simpler system which obtains elsewhere, and can consequently readily imagine the increased difficulty with us. Each furnace employs an " expert," and even with this precaution, the system is not conducive, at all times, to amicable relations between buyers and sellers. I am told that it was adopted at the time Southern irons were seeking a market; but it still remains, although the time has come when our iron is sought for and has obtained for itself a place in the markets of the country. The grades are as follows:

Jan 1, 1889

By John V. Beall

With some difficulty we framed the picture of the village on the mountain getting in the railroad bridge and tunnel at the base. It was a charming scene of red-tile roofs on a green mountain in the golden autumn sunshine with the black hole of the railroad tunnel looking like something out of the movie, "The Train." We clicked the shutter, advanced the film and started back to our rented Audi. At which point there was a hail from the other side of the railroad bridge. A man in uniform was brandishing an object in the air which looked suspiciously like a rifle. We peered around. We were the only other persons in view. He must be yelling at us. He was now closing the distance at a brisk, determined gait but was still 100 yards away. The car was handy but the road was straight, paralleling the railroad tracks for some distance. We dismissed the idea of running for it. Who knows, he might shoot. When he came up we didn't have much of a conversation because it had taken us a week to learn three words of Yugoslavian-zhiveli, long life, huhvalla, thank you, and schlivavitza, the national drink (plum brandy). None of these seemed appropriate. We got the Idea that photographs of railroad tunnels and bridges were prohibited. The guard, for such he seemed to be, took the Audi plate number, administered a last scowling reprimand and stalked off. This incident was the only one in a 15-day visit to Yugoslavia which we would have associated with "Iron Curtain restrictions."

Jan 1, 1970

Discussion of the paper of Earl S. Bardwell, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. .1429 to 1441. H. O. HOFMAN, Boston, Mass. (communication to the Secretary*) :-It is pleasing to the originators of the planimetric determination of oxygen in refined copper to see that the method has been taken up by a large smelting plant to be used in every-day work after it has been simplified to suit the new conditions. Several years ago Huntington and Desch 1 had improved our mode of working. They projected the developed negative on to a screen, traced the outlines of the picture with a pencil, drew a border, and measured one constituent with. the planimeter. In order to give the work greater precision, they divided the area into squares of 1 cm. side, shaded the

Jan 11, 1913

By Donald E. Meyer

High current-low voltage EB-gun evaporation in an oil-free ultra-high vacuum system was found to be necessary, though not sufficient, for stability (300°C, 106 v per on) of aluminium gate MOSFET's and MOS capacitors not stabilized by a phosphorous glaze. five characteristics of the equipment used: 1) Vacuum purification of the aluminum charge, 2) Ionization of the evaporant by the electron beam, 3) X-ray formation, 4) Residual gases during evaporation, and 5) Metal film structure were studied as Possibly significant in MOS fabrication. EVAPORATION of contact metals common to the semiconductor industry historically has been accomplished with oil diffusion pump systems and various resistance heated evaporant sources as dictated by the type of metal evaporated. To meet a need for greater reliability of semiconductor devices, other metallization methods were developed. A good example would be application of the moly-gold contact system to integrated circuits with deposition by RF or triode sputtering.' More recently, fabrication of stable metal-oxide-silicon devices and circuits has put new demands on metallization. The purity of the thin metal films composing MOS structures is critical, particularly at the metal-oxide interface, and ultra-high vacuum metallization using sputter-ion pumping and electron beam gun (EB-gun) evaporation are well suited for the task. At this laboratory aluminum has been the most common contact-gate metal for both MOS capacitors and MOSFET's. In the earliest work with MOS capacitors, aluminum was evaporated from wetted tungsten filaments using both diffusion pump and ion pump vacuum systems. In spite of clean oxide techniques these capacitors were unstable under bias-tempera-ture stressing. Only after a switch to EB evaporation of aluminum were stable capacitors produced. Using the same techniques it was possible to make MOSFET's with equivalent stability. Stability data for a discrete MOSFET is shown in Fig. 1. This is a "clean" oxide gate (no phosphorus stabilization or no etch back of a thicker gate) having a thickness of lOOO? thermally grown on the (111) plane. Gate length after diffusion was 0.24 mils, and the devices were hermetically sealed. Stressing conditions were 300°C and 106 v per cm applied alternately as a positive and negative field for 10 min, 50 min, and 4 hr for a total stress time of 10 hr. An initial shift in turn-on voltage of 0.1 v was detected for 10 min of positive bias. All evidence at this laboratory indicated that while EB-gun evaporation of ultra-high purity aluminum was not sufficient for 300°C stability, it did seem to be necessary. There may well then be something inherent in the EB-gun deposition used which enhanced stability, and probably no single factor existed but rather a series of factors. It is the purpose of this paper to report on some of the investigations carried out to learn more about EB-gun evaporation in ultra-high vacuum systems. EXPERIMENTAL DESCRIPTION The EB-gun was self accelerated, had a maximum power rating of 10 kw, and used a water-cooled copper crucible able to hold a 20-g aluminum charge. The electron beam was bent 180 deg and focused by an electromagnet which also provided movement of the beam across the crucible. Normal power conditions in this work were 9 kv and 300 to 600 mamp. The gun can be described as high-cur rent/low-voltage and was quite different in its mechanism of operation from EB-guns with much higher acceleration potentials. An oil-free vacuum system capable of 5 x 10- l0torr, a quartz crystal rate and thickness monitor and a quadruple mass spectrometer completed the evaporation system, Fig. 2. A typical evaporation cycle consisted of a 3 to 4 hr pumpdown to the upper l0-9 range and evaporation at l0? per sec with the pressure in the bell jar not rising above 1 x 10"7 torr. Thickness control was 5 pct or less and could be automatically monitored and controlled. Five phenomena associated with the EB evaporation and considered as possible contributors to Ma performance included a purification effect, ionization of evaporating aluminum, X-rays, constitution of vacuum ambient during evaporation, and film structure dependence upon evaporation rate. These phenomena are now discussed. Vacuum Purification. The design of the EB-gun permitted purification of the aluminum charge by vacuum outgassing. Particular features included an efficiently water-cooled copper hearth with a capacity of over 20 g of aluminum and the capability for sweeping the beam across the charge. Such capacity meant that aluminum had to be added only after about every fifth evaporation. A new charge was not required each evaporation as is necessary with filament evaporation. An oxide "scum" which appeared on the charge could be completely cleared from the top hemisphere of the charge by sweeping with the beam prior to opening the shutter. An indication of the purifying effect was obtained by a series of analytical measurements on incoming aluminum, after melting but with little vacuum out-gassing, after 30 min outgassing, and the evaporated film itself. Either a solids (spark source) mass spectrometer or an emission spectrometer were used for analyzing the aluminum charge. Analysis of the evapo-

Jan 1, 1970

By George J. Bancroft

Western Australia (often popularly called Westralia) comprises all of the Australian continent west of the 129th meridian. The latest census, that of 1895, gives it a population of 101,235 persons. It includes within its bouiidaries 975,920 square miles. About half the colony lies within the tropics. The climate varies but slightly, considering the vastuess of' the area. The interior is dry and hot, and subject to very sudden changes. The coasts are warm, and the rainfall abundant, varying from 20 to 40 inches per annum. Perth is the capital and principal town, having a population of 20,000. Fremantle (pop. 9000), distant 12 miles, is the port of Perth, but because it is out of the track of the mail steamers, the mail and passengers are landed at Albany (pop. 3000) on St. George's Sound. A railroad, 338 miles long, connects Pert11 with Albany, and the running time of trains is about fifteen hours. Kalgoorlie is only about 200 miles from the coast at the little village of Esperance; but to reach Kalgoorlie one must land at Albany, travel to Northam, within 66 miles of Perth, and then east at an acute angle 325 miles to Kalgoorlie; in all about 600 miles. From Perth a railroad also runs to the Murchison gold-fields by way of Mingenew, Mnllewa and Yalgoo, to Cue. A branch goes down to the port of Geraldton. The government operates all the railroads and telegraph lines, and has been very energetic, all things considered, in extending them into the gold-fields. As to the accommodations afforded by the railroads, the less said the better. The comforts of travel are conspicuous by their absence. Of the 975,920 square miles of Westralia, the government, in its magnificent way, cleclares 256,060 to be gold-bearing. There are the Kimberley fields in the north, of 47,000 square miles; the Pilbarra on the northwest coast, of 45,600 square

Jan 1, 1899

By Maurice Ewing, J. A. Peoples, J. W. Peoples, A. P. Craby

The purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data summarized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the opportunity for checking results so thoroughly is given. In the second place, the fact that recent commentatorsl,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1921, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected 'his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By Maurice Ewing, A. P. Craby, J. W. Peoples, J. A. Peoples

The purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data summarized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the opportunity for checking results so thoroughly is given. In the second place, the fact that recent commentatorsl,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1921, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected 'his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

The meeting of the Institute of Metals Division was held in Phila-delphia from Sept. 30 to Oct. 2, inclusive. On Monday evening preceding the meeting, a dinner was held at the Ritz-Carlton Hotel at which many of the former officers of the Division and of the present officers and execu-tive committee were present. The subject of a membership committee was discussed and a motion to appoint such a committee with powers to go over the membership list for the selection of divisional members and to institute plans for additional members was passed. Mr. H. E. Howe and Dr. Johnston of the National Research Council attended the meeting and presented their plans for an Alloys Research Association. Many opinions were voiced as to the practicability of such a scheme and Mr. Howe expressed himself in appreciation of the cooperative thought and efforts given him. On Tuesday morning the Institute of Metals Division joined sessions with the American Foundrymen's Association and listened to the opening addresses. In the afternoon a boat ride was taken on the Delaware River, visiting the plants of the Cramp Ship and Engine Building Co. and the shipyard of the Emergency Fleet Corpn. at Hog Island. The launching of the boat christened "Afoundria" at 5 p.m. was witnessed by members of the party. The opening technical session was held on Tuesday evening at the Ritz-Carlton Hotel at 8 o'clock. The next session was held at the Ritz-Carlton at 10 o'clock on Wednesday morning and the final session at the same time and place on Thursday morning. The sessions were well attended and the discussion was good. The highly technical nature of some of the papers on the program was of special note. Taken as a whole the meeting was one of the most successful ever held. The follow-ing papers were presented:

Jan 11, 1919

Jan 1, 1896

By W. L. Crentz, E. E. Donath, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By E. E. Donath, W. L. Crentz, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

[Executive HENRY A. BUEHLER, Chairman ERLE V. DAVELER EDGAR RICHARD JOHN M. LOVEJOY WILLIAM WRAITH J. V. W. REYNDERS, Consultant Finance HENRY KRUMB, Chairman E. E. ELLIS PAUL D. MERICA H. G. MOULTON, Consultant]

Jan 1, 1936

By Lawrence A. Soltis

Senior engineering or executive management positions are filled by engineers who are evaluated on their performance, knowledge, skill, and maturity. Not only is technical expertise required but a knowledge of sales and marketing, finance, law, industrial relations, and public affairs is necessary. The University of Wisconsin-Extension offers an innovative post-baccalaureate degree program blending technical and professional subjects the Professional Development Degree in engineering (PDD)-designed to bring various opportunities for learn-

Jan 4, 1978

By J. K. Brooke, F. A. Renninger

During 1966, crushed stone production in the United States totaled just over 811 million tons valued at almost $1.2 billion. This represented in- creases of 4 % in tonnage and 5 % in value over that for 1965. Excluding the crushed stone used for agricultural and certain industrial purposes (cement, lime and flux), crushed stone mineral aggregate production totaled 616.3 million tons valued at almost $910 million, also up roughly 4% in tonnage and 5% in value over the 1965 figures. Limestone was by far the most widely used rock variety, followed by basalt, granite and sandstone in that order. Concrete aggregate and roadstone continued as the main uses for stone, accounting for 63% of all tonnage produced in 1966 and 60% of total stone value. Sand and gravel production in 1966 increased 3% over that for 1965. Total 1966 output was just in excess of 934 million tons valued at almost $985 million as compared with 908 million tons at $957 million for the previous year. Excluding the higher valued industrial sands, 903.2 million tons of sand and gravel valued at $891.6 million were used directly as mineral aggregates, representing a 2.9% increase in tonnage and a 2.4% increase in value over 1965.

Jan 2, 1968

By Richard H. Bube

Photoelectronic radiation detectors may be conveniently classified as homogeneous intrinsic, homogeneom extrinsic, or junction type. Highly photosensitive homogeneous intrinsic photodetectors may be prepared from a number of different II-VI, III-V, or IV materials. Such materials require the presence of specific imperfections that can act as sensitizing centers to provide long majority carrier lifetime. Homogeneous extrinsic photodetectors are of interest primarity for infrared detection, and consist principully of germaniuim and silicon with suitable inpurities. A vaviety of junction photodetectors exist, with silicon us the most common material for them all. The following extrema in performance are found: 1) highest photoconductivity gain in homogeneous intrinsic photodetectors; 2) smallest response time (highest frequency response) in p-i-n junctions; 3) largest gain-bandwidth product in avalanche diodes. ALTHOUGH the total number of materials exhibiting photoconductivity effects is very large, only a relatively few of these have appropriate properties for a practical photoelectronic radiation detector. In fact if one surveys the commercial detectors currently available, one finds that the field is dominated by some ten or fewer materials. These are summarized in Table 1 in terms of the other important variable in detector fabrication, the structure of the material, i.e., whether the material is used as a single crystal or in polycrystalline form, and whether the material is used as a homogeneous detector or whether the detector depends upon the existence of a junction or barrier in the material. The principal wavelength range for each type of material is also shown, together with an indication of the utilization of intrinsic or extrinsic excitation. For the purposes of the present comparison of various detectors, it will be convenient to discuss two main topics: homogeneous photodetectors and junction photodetectors. The performance of a photoelectronic radiation detector is measured in terms of two parameters: the photoconductivity gain, and the response time of the detector. A convenient figure-of-merit is given by the ratio of gain to response time, often called the gain-bandwidth product. The photoconductivity gain is a device parameter since it varies in many cases with the applied voltage and the detector geometry, and should be distinguished from the actual photosensitivity of the material involved. This photosensitivity can be conveniently given as the product of free carrier lifetime and mobility in the material. The photoconductivity gain is defined as the number of charge carriers which pass between the electrodes per second for each photon absorbed per second, where G is the photoconductivity gain, is the pho-tocurrent in amperes, e is the electronic charge in coulombs, and F is the total number of electron-hole pairs created in the photo conductor per second by the absorption of light. The gain may also be expressed as the ratio of the lifetime of a free carrier to the transit time for that carrier, i.e., the time required for the carrier to move between the electrodes. For a material in which one-carrier conductivity dominates, where T is the lifetime of a free carrier, ttr is the transit time for this carrier, p is the carrier mobil-ity, V is the applied voltage, and L is the electrode spacing. From Eq. [2] it follows that the photoconductivity gain is proportional to the photosensitivity of the material (tP), the proportionality constant being The photosensitivity of a material, and hence the photoconductivity gain of a device utilizing the material, depends on the lifetime of the free carriers as a critical parameter. In a homogeneous material this lifetime is determined by the nature of imperfections in the material, and in an inhomogeneous material the lifetime is determined by the specific junction structure. The speed of response, the other basic photodetec-tor parameter, is determined by factors quite similar to those important for photoconductivity gain. Imperfections are of primary importance in homogeneous materials, and the structure of the junction is a determining factor in junction devices. For infrared detectors it has become common to define another quantity designed to indicate directly how effective the detector is in distinguishing between a small photoconductivity signal and random noise due to the detector and its environment. The detectivity D* is given by

Jan 1, 1968