Search Documents

By D. G. Russell

Two techniques have been developed with which the applicability of pressure build-up analyses can be extended to include pressure data which previously have been considered virtually unusable. One of the interpretation methods makes possible the analysis of pressure build-up performance during the wellbore fill-up or after production period which occurs soon after a well is closed in. The other technique is an extension of a method for analyzing pressure build-up performance during the late-time portion of the pressure build-up which occurs after boundary eflects first begin to alter the shape of a conventional pressure build-up curve. With both of these methods it is possible to obtain estitnates of the kh product, the skin factor and the reservoir pressure. In addition, with the late-time analysis technique it is possible to obtain an estimate of the contributory drainage volume of the well being tested. This means that in some cases a check on reservoir limit test and (or) material-balance calculations can now be obtained from pressure build-ups. Both methods are slightly more time-consuming than conventional pressure build-up analysis methods because trial-and-error plots of pressure data must be made. The late-time method for analysis of pressure build-ups is in principle applicable to the late-time portion of a two-rate flow test or a pressure drawdown test. The interpretation formulas and procedures for these types of tests are also outlined. In these cases, as with pressure build-ups, it is significant that an estimate of the contributory pore volume is also obtained. On the basis of limited experience with the new techniques, it appears that satisfactory estimates of the kh product, skin factor, reservoir pressure and, for late-time analysis, contributory drainage volume can be obtained. INTRODUCTION The analysis of bottom-hole pressure build-up behavior in closed-in wells has been a a subject of interest in petroleum engineering circles for many years. In fact, few other subjects have received as much attention as pressure buildup analysis methods have. The cause for this interest is essentially twofold in nature. First, the pressure behavior of a well can normally be measured with a reasonably high degree of accuracy so that good data for analysis can be obtained. Secondly, over a fairly wide range of operating conditions, valuable information as to the quality of the reservoir rock and completion efficiency of the well can be obtained at a nominal cost. In recent years, numerous papers have been prepared on the effects of various operating conditions and reservoir heterogeneities on pressure buildup behavior. Very little work has been done, however, on extension of pressure build-up analysis methods to those pressure data which are not amenable to analysis by the present methods. The theory upon which the analysis of shut-in bottom-hole pressure build-up data is based is derived from the solution of the radial flow equation for a slightly compressible fluid for constant-rate conditions. It requires that the well be closed in for a sufficient period of time to obtain a clearly defined linear portion on the plot of observed bottom-hole pressure vs log (t + ?t)/ ?t (where At is shut-in time, and t is producing time to the instant of shut-in). From the slope of the plot and other normally obtainable data, the formation permeability, the well damage or skin factor, and the reservoir pressure at infinite shut-in time (if the reservoir were infinite) can be estimated. The successful application of this procedure depends on being able to recognize the straight-line section on the basic pressure build-up plot. The presently used pressure build-up interpretation theory also assumes that a well is closed in at the sand face and that no production into the well occurs after shut-in. In practice, of course, the well is closed in at the surface, and inflow into the well continues until the well fills sufficiently to transmit the effect of closing-in to the formation. This adjustment period is commonly referred to as the "afterproduction" or "fill-up" portion of the pressure build-up. During the period that the well fill-up effect is most pronounced, the basic pressure build-up plot is nonlinear. At later shut-in times after the effects of a drainage boundary have been felt at the well, deviation from the straight-line behavior of the pressure build-up plot also results. In many cases either of these effects or a combination of both can make the straight-line portion on the pressure build-up plot difficult to recognize. Obviously, an extension of pressure build-up analysis methods to include the afterproduction period and the period in which boundary effects are being felt would be desirable and might render valuable pressure data which for years have been considered virtually unusable. The principal reference of note concerning pressure buildup analysis during the afterproduction period is a paper by Gladfelter, Tracy and Wilsey.1 In the approach of these authors it is necessary to measure the rate of influx into the well during the afterproduction period. This is done through sonic measurements or through measurement of tubing-head and casing-head pressures simultaneously with

Jan 1, 1967

By P. B. Knuckey, D. Littleford

The Kalengwa mine, situated in a remote area of Zambia in Central Africa, has presented some unique problems to the planners engaged in developing the deposit. This small, high grade copper deposit contains some 1,688,000 tons of ore at a grade of 9.3% contained copper. Of this 362,000 tons is classified as high grade ore at 27.2% Cu, the coarse fraction of which can be fed directly to converters; 733,000 is classed as intermediate grade ore averaging 6.3% Cu, and 593,000 tons classed as low grade ore containing 2.1% Cu. The geology of the deposit and the establishment of the mining operation is fully described. A concentrator is being built at Kalengwa to treat the high grade fine product, intermediate, and low grade ore, whilst the coarse high grade ore will be trucked to the Copperbelt smelters for direct smelting. Details of metallurgical processing are given. The decision to truck the coarse high grade ore to the smelters on the Copperbelt necessitated the construction of a new 200-mile road, the setting up of a fleet of heavy ore transport trucks and associated equipment. The remoteness of the area from established communication facilities on the Copperbelt necessitated the provision of radio communications between Kalengwa and the head office at Kalulushi, and the establishment of a regular mine air service. The paper also describes the training of an unsophisticated local population in the operation of heavy plant and machinery, the establishment of the township, and the provision of health services.

Jan 1, 1972

By B. Habermann

Artificially consolidated sand models, representing one-quarter of a five-spot, have been developed and used to study factors aflecting misciblt. displacrmenr. Sweep efficiency at breakthrough, size of the mixing zone between two miscible liquids and per cent area contacted by drive after breakthrough were determined tor the high mobility ratios encountered in actual resvrvoirs. Quantitative relationships between the degree of viscous fingering and mobility ratio were obtained by measuring the length of the fluid interface. Scaled miscible-slug experiments, supported by field evidence reported in the literature, have shown that when the slug is followed by dry gas the process is less efficient than expected. In addition to low areal sweep efficiencies encountered for high mobility ratio displacements, the effectiveness of a miscible slug is greatly reduced. This is caused by an accelerated growth of the mixing zone between the driving and the displacing fluids. INTRODUCTION Considerable interest in miscible displacement as a secondary recovery process has been shown by the oil industry in recent years. In addition to extensive laboratory investigations, numerous field operations have been initiated so that 39 miscible displacement projects had been reported' in the United States by early 1959. By far the most popular approach in these projects is the use of an LPG slug followed by dry gas. Laboratory tests have indicated that with a small miscible slug, amounting to several per cent of the hydrocarbon pore volume, practically 100 per cent recovery of the oil in place can be achieved and that all of the slug material can be recovered by a subsequellt gas drive. However, these experiments were conducted on small-diameter long cores that can be considered as essentially uni-dimensional reservoirs that do not represent actual field conditions. It soon became apparent that the inherently adverse mobility ratios existing in the reservoir cannot be ignored in any miscible displacement field project. When a less viscous fiuid such as an LPG slug drives a more viscous reservoir oil, fingers develop that reduce the areal sweep efficiency. The slze of the miscible slug to be used is a subject of some controversy. It has been proposed that the size of siug needed be calculated by setting lengths of the mixing zone proportional to the square root of the distance traveled. This proposal is based on experimental evidence' and theoretical considerations"' in which fingering was not a factor. A prerequisite for successful application of the miscible displacement process to field operations is a better understanding of the following factors. L What is the effect of mobility ratio on the rate of deterioration of a miscible slug? 2. How large a slug should be used for given reservoir conditions? 3. What is the sweep efficiency? The purpose of this investigation was to provide some additional laboratory data that should help to answer these questions. More specifically, it was intended to study more quantitatively the effect of viscous fiinger-ing, mobility ratio and slug size on the efficiency of this relatively new secondary recovery process by means of experiments on thin, horizontal, porous medium models.

SECTION I Page Page Report of Nominating Committee. v Employment li Proceedings of St. Louis meeting. , vi Local Section News.: liv Engineering Foundation, Report Affiliated Student Societies lvi of Secretary xxxviii Forthcoming Meetings lvii Engineering Council xlii. Library lviii Suggested College Course on the Membership lxiii Human Side of Engineering... xlii Biographical Notices: Engineering Societies Club of Alexander Bryden. By C. L. Hawaii xlv Bryden lxxxiii Members in Military Service .... xlv E. F. R o e b e r . B y J. W. Meeting of Board of Directors...' xlvii Richards lxxxv 1918 Dues xlviii Institute Committees lxxxvi Transactions for 1917 xlviii Officers and Directors xciv Personal xlix

Jan 12, 1917

By J. Hall Carpenter, James E. Lawver

Shortly after the passage of the Taconite Amendment in Minnesota, several mining companies announced their intention to build new magnetite taconite plants and another announced its intention to augment present facilities. It is clear that Minnesota will enjoy an expanding magnetite taconite industry, but despite the fact that the reserves are large, eventually they will have to be supplemented by oxidized deposits. Furthermore, not all producers have magnetite taconite reserves. Due to the extensive oxidation of most of the western part of the Mesabi Range, there are no large blocks of unaltered magnetite taconite that lend themselves to open pit operations. Unless a commercial process can be developed to concentrate the oxidized, or so- called "nonmagnetic", taconite and semi-taconite, the existing mines operating in the western part of the range will be forced to shut down when the direct shipping, wash and gravity ores are depleted, or are no longer salable, because of their poor quality compared to high-grade pellets. KNOWN PROCESSES COSTLY The enormous reserves of the oxidized iron- bearing formation have offered a tantalizing challenge to metallurgists for many years. In fact, several processes for concentrating certain types of oxidized ore have been successful at both laboratory and pilot plant level, but to date no process for concentrating semitaconite or oxidized taconite has reached commercial fruition. Magnetic roasting, followed by low-intensity magnetic separation1, has shown considerable promise because the high iron recovery makes the ratio of concentration of many of the oxidized ores more favorable than that of magnetite taconite. However, the capital and operating costs are high and, in many cases, a high- grade concentrate cannot be made without resorting to flotation of the magnetic concentrate. Hence, most research groups are investigating alternate methods of concentration with the hopes of reducing the cost.

Jan 9, 1965

By Robert F. Mehl, Edward L. McCandless

Oriented overgrowths and intergrowths among both metallic and nonmetallic substances have been recognized and studied for well over a century. The work of Widmanstätten in 1808 on the geometrical structure in meteorites, a structure known by his name, demonstrated that oriented intergrowths can occur in purely metallic systems. This fact led to much of the early microscopic study of alloys, contributing greatly to the advance of physical metallurgy. The problem has been attacked again in recent years in a comprehensive fashion, with the object of discovering what atomic movements may occur during phase changes in alloy systems. Much of this work has appeared in the A.I.M.E. Transactions in a series of papers published by Mehl and coworkers beginning in 19311. Although many aspects of this general problem remain unsolved, it may be said that the orientation of a new phase forming by precipitation from solid solution or by transformation invariably bears a unique relationship to the orientation of the phase from which it formed, and that similarity in atomic patterns on atomic planes in the two phases play an important part in determining the orientation relationship. Analogous orientation relationships exist in oriented intergrowths in nonmetallic systems—mineral or inorganic. In 1827 Haidinger2 discovered natural intergrowths of hematite and magnetite, and demonstrated that the rough form of the magnetite octahedrons was delineated by small crystals of hematite, of which the basal (00.1) planes lay parallel to the octahedral cleavage planes of the magnetite. The description of this orientation relationship was later completed by von Rath3, who showed that the edge (00.1): (10.1) in hematite lies normal to the [Ill]

Jan 1, 1937

By R. Dawson Hall

WHAT are the opportunities for the services of engineers in the coal mines? The best answer perhaps can be made by detailing the present lines of development in the bituminous coal mining regions. They are just at the beginning of a period that can be conservatively termed revolutionary. A few glimpses of new possibilities in economic mining that will reduce the cost of bituminous coal at the mines by at least one half have convinced almost everyone that a change must shortly come about. The cost of housing has become such a burden, especially in mountainous regions, that development which demands the hiring of more men and constructing more houses would not be profitable. The introduction of mechanical aids to mining, transportation and dumping suggests a way of obtaining a large tonnage with the same or a smaller number of men with no further house construction. At the same time the restriction of immigration has made it increasingly difficult to obtain men inured to hard labor. Modern civilization is not productive of muscular energy and at the same time it provides men who are not indisposed to the use of the mental effort required to direct the physical forces now available for the replacement of such energy.

Jan 1, 1924

By Thomas C. Patton, Eric S. Cheney

L-D gold mine is 3 miles south of Wenatchee, central Washington. Recognition of locally mappable conglomerates, sandstones, and shales within the Paleocene (?) Swauk formation led to the discovery that the known epithermal gold mineraliza¬tion is limited to a previously unknown imbricate thrust zone of unknown displace¬ment cutting the open folds o f the area. Hypabyssal intrusions also are most nu¬merous along the trace of the thrust faults. Yakima basalt of Miocene age uncon¬formably overlies the Swauk formation, thrust faults, and the intrusions. The L-D mine is in a northwesterly trending imbricate fault block of nearly vertical strata. Microscopic native gold, electrum, and naumannite occur in quartz veins and as low¬grade disseminations in the well-silicified portions of arkosic sandstones. Fault gouge on the "footwall fissure" limits ore to the hanging-wall block of the fault. Epithermal mineralization and alteration are spatially related to the nearby intrusions. Right lateral north-south faults offset the ore a maximum of 300-400 ft along any one fault. From 1949 until January 1967, when the L-D mine closed, 1,036,572 dry tons of ore valued at $14,962,305 and averaging 0.396 oz Au per ton and 0.607 oz Ag per ton were mined. Recognition of the structural control of the mineralization and altera¬tion within the Swauk formation suggests several areas within and outside of the mine that warrant further exploration. For example, the high-angle faults, imbricate thrusts, and the intrusions of this area are on strike with similar features along the major Entiat fault zone 10 miles to the northwest. The L-D gold mine (previously called Squilchuck, Wenatchee, Golden King, Gold King, and Lovitt) is located in Squilchuck Canyon about three miles south of Wenatchee, Chelan County, Wash. (Fig. 1) on the eastern edge of the Cascade Mountains. The major stratigraphic unit in the area is the nonmarine early Tertiary Swauk formation, which is predominantly com¬posed of arkosic sandstone. The lack of laterally per¬sistent units and the paucity of outcrops heretofore have precluded all but the grossest subdivision of the Swauk.' As a result, the true significance of the open folds in the Wenatchee area was not recognized, and although the geology within the mine was known, the structural setting of the mine was virtually unknown. During the present investigation, several locally map¬pable units were discovered within the Swauk which, in conjunction with mine maps, indicate an imbricate thrust zone. The epithermal gold mineralization, most of the hypabyssal intrusions, and the zones of hydrother¬mal alteration are located within or near this thrust zone. The purpose of this paper is to: (1) to describe this structural setting, rather than the detailed mine geology already presented by Lovitt and Skerl,2 and (2) to sug¬gest that from an exploration standpoint, this struc¬tural setting may be repeated in areas inside and outside of the mine area. Stratigraphy and Structure of the Swauk Formation General: The Swauk formation contains three distinct lithologies. Typical Swauk sandstone is gray on fresh surfaces, poorly sorted, weathers tan, and is cross¬bedded; it consists of 40-60% quartz, 20-40% feldspar, and up to 10% muscovite and biotite 9 The typical shale is gray to dark brown, very soft, and interbedded with silty sandstones; sharp contacts exist between the

Jan 1, 1972

By A. V. UDELL

OF all the metals that have from time to time been called the "Wonder Metal," mercury, often called quicksilver, is probably the most deserving of this designation. A wonder metal it must have been to those workers of an earlier day who named it after that Latin god of commerce and gain, characterized as the fleet messenger of the gods and the conductor of souls to the lower world. The word mercury has been used to indicate a carrier of tidings, a bearer of news, a nimble or clever person, a hawker, and a skillful thief. All of these attributes, and more, are recognizable in this metal, the technical terminology of which is "Hydragyrum," meaning water-silver, and from which the chemical symbol "Hg" is derived. Fickle in its occurrence in nature, simple in its metallurgy, illusive in captivity, it serves man in life or death, in war or peace, in commerce, science and arts, in mining, agriculture, and forestry with a versatility found in no other element.

Jan 1, 1929

SPEAKING generally, it may be said that leaching is the simplest method of recovering copper from its ores. Likewise it is perhaps the oldest method of treatment used by copper metallurgists of the modern era. Reliable records indicate that as early as 1752 cupriferous pyrite was leached in the famous Rio Tinto region in Spain. Though the manipulation was quite different from that in use today at Chuquicamata, New Cornelia, Inspiration, and Andes, it resembled that employed by Phelps Dodge at Bisbee, as described in Chapter XIV. Leaching consists of subjecting ore to the action of a liquid solvent or menstruum (usually an aqueous solution) which dissolves the major part of the soluble copper minerals. The resulting pregnant solution is drained off or otherwise separated from the residual ore; and the copper in the solution is then recovered by some appropriate means of precipitation. When sulphuric acid is the lixiviant, as is usual, the simplest procedure is to pass the copper-bearing solution through large troughs containing scrap iron. The iron displaces the copper in the solution, precipitating it as a slime coating the iron and varying in color -from bright copper to a dull black. This may be washed off at intervals, collected as a sludge, dried, and melted with a little fluxing material to produce reasonably pure copper. Usually, of course, the mud is sent to a smelter where most often its destination is the converter or reverberatory furnace. Modern practice uses precipitation on iron only as a complemental process to electrolytic precipitation or deposition, wherein the pregnant copper-bearing solution, acting as the electrolyte in a cell having insoluble anodes and copper cathodes, is depleted of the copper it contains. Cathode copper, 99.5 per cent pure, is produced ready for the market as refined copper, or for a simple process of melting, fire-refining, and casting in

Jan 1, 1933

By H. H. Hausner, H. S. Kalish

IN recent years zirconium and beryllium have become of great interest because of their special properties. Zirconium is known for its remarkable ability to absorb the gases oxygen, nitrogen and hydrogen, has extensive use as a getter in electron tubes and has indeed become the primary metal in the manufacture of photoflash bulbs. Beryllium is of interest because it is light metal and as such could supplement aluminum and magnesium in light metal applications. The late development of zirconium ductile at room temperature produced by both the iodide and calcium reduction methods has stimulated frequent articles on this metal in the recent literature. Beryllium is so closely akin to zirconium crystall-ographically that some investigators are of the opinion that beryllium should be ductile at room temperature if it were pure enough. The crystallographic relationship of beryllium and zirconium, the interest created in Be-Zr alloys where the zirconium is believed to function as a remover of solid solution gas in beryllium and thus increase the ductility of the beryllium rich alloy, and the amenability of these metals to powder metallurgy methods stimulated this approach to an investigation of the system Be-Zr. Preliminary work showed that a zirconium compact melted when pressed in contact with a beryllium compact and sintered at 1250°C, without any apparent final bond between the two. A search of the literature revealed nothing pertinent about the Zr-Be system or about any zirconium - beryllium alloys. In 1936 Misch³ vaguely identified the compound ZrBe2 and reported that it has a deformed cubic structure. Two patents," , were issued to Mach-lett Laboratories in 1943 and in 1946 regarding the addition of small amounts of zirconium to beryllium in order to improve the ductility of beryllium so that it may better be used for X ray windows. In considering the alloy formation of beryllium with other metals Raynor thought it unlikely that zirconium would have any solid solubility in beryllium. From this indefinite information nothing could be ascertained about the possible use of Zr-Be alloys or the use of these metals intimately. A brief preliminary study of the system Zr-Be by powder metallurgy methods was undertaken to provide regions for more intense studies of Zr-Be alloys and as a guide to a formal phase diagram determination. The investigation described in the following pages was completed in less than three weeks. The usefulness of this rapid method to facilitate phase diagram studies and new alloy investigations will be shown. Materials and Procedure Zirconium powder was produced from crystal bar stock of high purity supplied by Foote Mineral Co. The crystal bar was converted to hydride at 730°C, crushed, and the hydride decomposed in purified argon at 850°C. 60 pct of the powder passed through a 325 mesh screen, 40 pct of the powder was —140 mesh, +325 mesh and the average particle size of the total was 8 to 12 microns. The beryllium powder was used as re-

Jan 1, 1951

By Rudolf Gahl

Some time ago the Detroit Copper Mining Co. had to decide the question whether it would pay to re-treat slime-tailings, and several machines were tested in order to ascertain the type of construction which would give the greatest saving. In previous tests on the ore of this company, several tables proved far inferior to the Frue vanner, and for this reason they did not receive any serious consideration. In the late tests, however, one table was found to surpass the vanner in the percentage of saving made. The Frue vanner used in these tests had been adjusted approximately to the slope which the slime-vanners in the concentrator of the Detroit Copper Co. had at that time, about 2 in. between the inside of the wooden posts, or 0.272 in. per ft. It had not been determined, however, if this slope was the most economical one for treating the slime-feed in the mill, or for re-treating the tailings from the slime-vanners, and I was instructed to ascertain by test-runs, under different conditions, the best adjustments for the work to be done. In order to determine if a change in the adjustments of the machines would improve the results, it seemed sufficient to continue running the tests between the vanner and the table before mentioned, keeping the feed and all other conditions the same, but varying the adjustments of the vanner from run to run. I employed a vanner-man of long experience to operate these machines, who expressed the opinion that a slope between 28 and 2.5 in. between the posts (0.323 and 0.340 in. per ft.) would give the best results. Some runs made this way gave a considerable improvement. While for a slope of 2 in. (0.272 in. per ft.) the saving had been only 40.5 per cent. of that of the table, it was 49.2 per cent. for 2.5 in. (0.340 in. per ft.) slope. A decrease of

Jan 1, 1910

By R. Schuhmann, O. W. Moles

at temperatures of 1150°, 1250°, and 1350°C for liquid copper sulphides ranging in composition from saturation with Cu to about 21.5 pct S. From the experimental data, activities of Cu, S, and Cu2S in the melts were calculated. Also, the results furnish a new determination of the location of the curve showing the compositions of Cu-saturoted sulphide melts in the CU-S constitution diagram. THE "white metal" made as an intermediate L product in converting copper matte to blister copper is a matte approximating Cu2S in composition. It has long been known that liquid Cu-S mattes can exist at a given temperature over an appreciable composition range, with S:Cu ratios ranging up from a lower limit corresponding to equilibrium of the matte with a liquid Cu phase. The Cu-saturated matte has somewhat less S than Cu2S, although previous measurements of the compositions of Cu-saturated mattes are not in good agreement.'" As the S:Cu ratio approaches and slightly exceeds that for Cu2S, the partial pressure of sulphur gas over the liquid matte rapidly approaches atmospheric pressure,5 so that Cu-S melts with much more S than Cu2S can be made and handled only in pressure apparatus. Accordingly, the liquid copper sulphides of interest in copper smelting and readily studied experimentally fall in a relatively narrow composi- tion range about Cu2S. The freezing points of Cu-S mattes show a maximum of 1129°C near the composition Cu, dropping to 1105oC for Cu-saturated mattes having less S and dropping under 1100°C for higher S mattes.' Estimates of the sulphur pressure and other thermodynamic properties of liquid Cu,S were made by Kelley; based on extrapolations from equilibrium measurements on solid Cu,S. More recently, Cox and coworkers' studied equilibria in the reaction: Cu,S + H, e 2Cu + H,S over the temperature range 700" to 1250°C. They measured equilibrium H2S:H2 ratios presumably with both the sulphide and the metal phase present, so that their data above the melting point of Cu,S should measure the S pressure of Cu-saturated sulphide melts. The sulphur pressures of liquid copper sulphides of several S:Cu ratios at their freezing points can be estimated from data given by Posnjak, Allen, and Merwin." However, beyond these few data, no systematic study seems to have been made of the relations of sulphur pressure and other chemical properties of liquid copper sulphides to composition and temperature. The measurements of the sulphur pressures of liquid copper sulphides reported in this paper represent a first step in the quantitative study of the chemistry of mattes. Similar work is planned on

Jan 1, 1952

By T. G. Decker, A. F. Witt, A. M. Gaudin

The historical development of the concept of contact angle hysteresis is reviewed. The measurements of contact angles reported in literature have all been made under static conditions. For the measurement of dynamic advancing and receding contact angles, four methods are described together with an evaluation of their precision. Three of these methods were adapted from devices already used for the measurement of static contact angles. The fourth method uses a new principle and apparatus and is the most accurate. While the relationship between surface tensions and the contact angle was extablished as early as 1805 by T. Young,' it was only in 1890 that the existence of contact angle hysteresis was reported by Lord Rayleigh. His observations, however, remained almost unnoticed. With the invention of froth flotation, the contact angle and its behavior became the subject of investigation. In 1907, L. Sulman and collaborators investigated the cause of discrepancies between recorded values of contact angles. They found that certain variations existed in most cases, but that definite maximum and minimum values of contact angles are obtainable. The difference between the maximum and the minimum contact angle in a given system was termed "hysteresis" by Sulman. First attempts to explain hysteresis were made by E. Edser. In the following years extensive studies of contact angles in various three-phase systems

Jan 1, 1963

By John Chipman, Carl F. Floe

The system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100" to 1500ºC., and pressures from about 20 mm. of mercury to somewhat above atmospheric. Review of Previous Work The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as O2, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: 2M+G2=2MG K=(MG)2 /M2 X PG2 [I] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: MG = K1 vPG2 [2 Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: 6Cu + SO2 = Cu2S + 2Cu2O [3] K= Cu2S X (Cu2O)2 i - (Cu)6(Pso2) [4] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: K1 =V3SO2 /Pso2 or

Jan 1, 1941

By Carl F. Floe, John Chipman

The system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100" to 1500ºC., and pressures from about 20 mm. of mercury to somewhat above atmospheric. Review of Previous Work The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as O2, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: 2M+G2=2MG K=(MG)2 /M2 X PG2 [I] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: MG = K1 vPG2 [2 Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: 6Cu + SO2 = Cu2S + 2Cu2O [3] K= Cu2S X (Cu2O)2 i - (Cu)6(Pso2) [4] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: K1 =V3SO2 /Pso2 or

Jan 1, 1941

By H. M. Howe

(New York: Meeting, October, 1913.) 1. INTRODUCTION.-This paper gives the results of our micro-graphic determinations of the position of Ae3 in a series of 14 hypo-eutectoid steels of varying carbon content, one of them very rich in phosphorus, and of SEe for one hyper-eutectoid steel. We have pro-ceeded chiefly by noting the temperature -at which the reabsorption of the pro-eutectoid element is found to be complete after a 30-min. holding, but in part also by noting the temperature at which its precipitation begins. Observations on these same steels by Messrs. Burgess, Crowe, and Rawdon, of the United States Bureau of Standards, are given in a paper' issued simultaneously with this, while in a third paper s one of us compares these data with those of earlier observers. These three papers are treated as one whole by numbering their sections, tables, and illustrations continuously, and by setting the folding plates of micrographs at the end of the last paper. THE COMPOSITION OF THE STEELS EXPERIMENTED ON is given in Table I. Notation. and Definitions.-Following Osmond's development of Tschernoff's notation; in which " Ac3 " is the upper limit of the hypo-eutectoid part of the transformation range as observed in heating up, and " Ar3 " is that same limit as observed in cooling down, and following the usual custom of calling the upper limit of the hyper-eutectoid part of that range "SE," we may go farther and call this latter limit " SEc " when observed in heating up .and " SEr " when observed in cooling down.

Jan 6, 1913

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

Last year the authors presented a paper that discussed the various electrical measurements they perform in drill holes, which they name "electrical coring."' The object of the present paper is to give a brief account of the points of scientific interest that have been elucidated by further field work and laboratory research, as well as the economic results that have been attained recently. The practical examples given in this paper are drawn, for the most part, from the field work performed in Russian oil fields during the years 1931 and 1932. This is due to the fact that, thanks to the comprehensive cooperation of the Russian geologists and scientists, the authors are allowed to make public a large amount of recant information. In other countries in which the authors are engaged in similar work, the competition between private companies makes it imperative, for a considerable lapse of time, to avoid publication of the results obtained. The following points will be discussed successively, under separate headings: 1. Electrochemical phenomena in drill holes. 2. Stratigraphic correlations and tectonic studies. 3. Relations' between the productivity of oil horizons and their electrical resistivity. 4. Location of coal seams. 5. Summary and conclusions. Electrochemical Phenomena in Drill Holes Technical Publication 462l described the author's discovery concerning the existence of important differences of potential spontaneously gener-

Jan 1, 1934

By Richard Rothwell

At the last meeting of the Institute, Mr. Per Larsson read a very interesting paper on the Chapin mine of Michigan, in which he described the systems of mining that had, at different times, been tried in that great ore-body, and especially the system now in use, which consists in working the ore out from the bottom upward in lifts. Shortly after that paper was written, but before it had been published, or that I had had an opportunity of reading it, I bad the pleasure of visiting the mine. At that time I was making a profes sional examination of a nnmber of the mines on theGogebic Range, and others in the Menominee region, Michigan and Wisconsin, and had occasion then, as during several previous visits, to study closely the methods and cost of mining in these districts. As the outcome of these investigations, it appeared evident to me that the system of working on the chamber-and-pillar plan, which up to that time had been the only method of underground work adopted in the Gogebic

Jan 1, 1888

By Charles C. Peterson, Ronald E. Enstrom

Significant improvements have been made in the ursine systern for epitaxial vapor gvowtlz of Gds. The electron concentration has been reduced to below 1015 cm-3 with electron-mobility values as high as 7200 sq on per v-sec at 30PK and 60,000 sq cw7 per v-sec at 77°K. These high-purity layers have been successfully gvown on n&apos; layers with thicknesses as snzall as 1 p and as large as 125 p. Furthermore, high-purity layers have been incorporated into an structure without degradation of electrical properties. Different impurity gradients at the n&apos; to n interface were achieved. Using these structures, Gunn oscillators have been operated at frequencies as low as 0.4 GHz and as high as 40 GHz, which equals the highest valzle yet reported. The frequencies nleasured are in reasonable apeenlent with those calculated fron7 the n-layer widths and the transit times. CW operatiolz has been achieved from 3 to 20 GHz. In Gunn devices for >40 GHz operation (i.e., witk an n-layer tkickness below 2.5p), the n layer has been generally too pure to permit oscillations to occuv. ThE mechanism of the Gunn oscillator&apos; is now generally understood.2-5 Electron transfer from the (000) minimum to the ( 100) minima leads to a voltage-controlled negative resistance, which results in the formation of domains of high and low electric fields which travel through the crystal with a characteristic velocity of about 107 cm per sec. When a constant voltage is applied to the sample, this domain motion generaliy leads to oscillations at the transit time frequency, fT = 107/L, where L is the thickness of the active n layer.&apos; In this case, a single high-field domain is nucleated at the cathode and grows until it reaches the anode, where it is absorbed; a new domain then forms at the cathode.5 There are related modes of oscillation of the same device in which a tuned circuit causes a periodic variation of the voltage across the device. The frequency then may be either above or below fT. It has been shown that oscillations will occur when n • L 2 1012 cm"2, where n is the carrier concentration in the active region. At lower doping densities, 10" 5 n . L 5 lo&apos;&apos;, the doping is said to be subcritical for oscillation and the description of the device operation changes since the domains become comparable in thickness to the device thickness, L. Nevertheless, such devices have been found to be "active" and, in fact, are useful as amplifiers.778 For CW operation, one wishes to minimize the power dissipation, which is related to the electric field, E, and the low-field resistivity, p. Below threshold, the power dissipation density is approximately Typically, at threshold where E -- 3 x 103 v per cm, the dissipation density is 107/p watts per cu cm, p in ohm-cm. Furthermore, it is desirable to provide good conduction of the heat generated in the active region. The temperature rise, AT, across the active layer of a sandwich structure, with a heat sink on one side, is given by AT = (E&apos;/P)(L~/~~) where it is assumed that the thermal conductivity, u, and resistivity, p, of GaAs do not vary appreciably over the range of temperature and electric fields existing in the layer. This expression shows that, subject to maintaining an appropriate (n . L) product, CW operation is favored by a higher resistivity, a lower threshold field, and a thinner device. The above device requirements place some severe restrictions on the materials to be used, especially for high-frequency (>10 GHz) operation. Here, it is necessary to prepare very thin (<10 µ) layers of GaAs, in a state of high purity (-1 ohm-cm), complete with very low-resistance ohmic contacts. Problems of handling such thin and fragile samples become inereasingly severe as the frequency is raised. Furthermore, while good low-resistance ohmic contacts are easily applied to low-resistivity GaAs, contacting difficulties are encountered for these higher-resistivity materials.

Jan 1, 1968