Search Documents

By Albert R. Ledoux

With the improvements in design and efficiency of machinery the element of danger in its use is becoming less, but it is a question whether the strain involved in operating modern plants is not increasing somewhat the danger of accident due to human fallibility. I propose to describe a somewhat uncommon casualty resulting from a not infrequent incident in the use of air-compressors. It is not necessary to state the location of the mine in which the accident occurred nor the makers of the compreseor, and the object of this brief paper is more to draw out suggestions from members more familiar than am I with the practical handling of mining machinery, than to point a moral. The compressor in question was a three-drill machine of standard make. At the time of the accident it was furnishing air to a single drill working in an upraise from a well-ventilated tunnel, and giving ventilation to a winze below the tnnnel where two men were hand-drilling. The compressor also furnished power to a small hoist in the winze, but the hoist was only operated occasionally, and never while the drills were working. The drills were located about 1200 ft. from the compressor. The engineer testified that he never had been short of air, and that there had been no complaillts that the

Jan 1, 1904

In an earlier day, a moderate-sized 600 tpd mine could easily require 60 working faces and might use five supervisors. The miner had a tonnage rate as an incentive and was largely his own boss. With the advent of conventional mining machine crews, the typical pattern of resource used changed radically. The number of work places could be cut by a factor of ten, but supervision only by a factor of somewhere around three, or at most, five. Obviously, supervision was increased. Capital use rose at the same time by a factor of approximately eight. Materials used, such as powder and bits, probably in- creased in both quality and unit cost, too. It certainly required a better-trained man to run the machines, but fewer miners were needed. It is clear that each input factor such as land, labor, capital and management, has changed significantly and it would be foolish to attribute all the gain to improved machines. However, concentration of work was a vital consideration in the change, sketched above, and such focusing of work in fewer areas could not have occurred without high capacity mining machines.

Jan 11, 1968

By Joseph W. Murray

Prior to 1950 Magma's ore production came from two parallel, steeply dipping, east-west striking mineralized faults, one called the Main or Magma vein and the other the Koerner vein, which lay about 1100 ft to the south. This vein system has been explored and mined over 9000 ft horizontally and 4800 ft vertically. In 1950 continued exploration led to the discovery and development of replacement orebodies in the Devonian limestone zones adjacent to the veins. These replacement deposits occur in the eastern part of the Magma mine and follow the strike and the 30º east dip of the host limestone. Strike length of the ore bodies varies from 250- 500 ft and thickness from 15-125 ft. The orebodies are large tabular masses with chalcopyrite and bornite being the dominant ore minerals. Hematite and pyrite are the most abundant gangue minerals. Incompetent limestone, shale, or a porphyry sill hanging wall is characteristic of portions of the replacement beds. In many instances the ore is blocky, badly fractured and intermixed with layers of limestone gouge, pyrite and hematite.

Jan 6, 1973

Discussion of the paper of Norman B. Braly, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1881 to 1906. GEORGE A. PACKARD, Butte, Mont.:-I would like to ask Mr. Braly if he has any information as to the relative efficiency of the sinking pump, using it as he refers to it, discharging the exhaust into the water column or otherwise. MR. BRALY :-I have never gathered any information on that point. It is a question of getting the work done. In driving the shaft, using that method, we find it easier on the men and everything else. In the bottom of the shaft, if you exhaust back into your column, it is a quiet. shaft. Another thing is the freezing: if you are sinking with air in your pump, you will find it is liable to freeze, and in that case as the air is still under compression it will not freeze the pump. The difference is very small if there is any. But, as might be expected, the pump is a little less efficient when exhausting the air into the column. MR. PACKARD :-I suppose all of us know what a pump in the bottom of the shaft is. My experience has been, although I have no figures, that the capacity of a pump is quite considerably decreased if you are pumping, say, from a depth of 200 ft. through a No. 7 Knowles pump, when you exhaust the air into a column, but, on the other hand, it is also my impression that we can raise the water to a little greater distance. I would like to get some figures from somebody who has made actual tests.

Jan 11, 1913

By E. M. Norris

Phosphate deposits are distributed widely over the earth's surface. Of the known areas of deposit, eight fields are of particular interest because of their vast reserves of high grade phosphatic material and the volume of their production that goes to the world's great consuming areas. These fields, in the order of their present economic importance, are situated respectively in Florida, French Morocco, Kola Peninsula of U.S.S.R., Tunisia and Algeria, Tennessee, Mon- tana-Idaho-Wyoming-Utah, Ocean and Naru Islands in the Gilbert group, and in Egypt. The Rocky Mountain deposits have a comparatively low ranking in the phosphate trade of today, but this field contains one of the largest known reserves of phosphatic material, associated with which are recoverable trace minerals, which are of increasing importance in our national economy. The first discoveries of phosphate rock in the western states were recorded in Cache1 and Rich² counties in Utah, respectively in 1889 and 1897. Mining operations were begun on these deposits near Montpelier, Idaho, in 1906. During the latter year geological studies of the phosphate beds were started by Weeks and Ferrier of the U. S. Geological Survey. These studies have been continued to the present day by a distinguished roster of the Survey's technicians. As a result of this systematic exploratory program, the Survey has published a series of bulletins, papers, and maps, which provide the mining public with a comprehensive study of the exposed

Jan 1, 1950

By John P. Bingham

GRACE mine and mill, owned by Bethlehem-Cuba Iron Mines Co. and operated by Bethlehem Cornwall Corp., are being developed to produce 9600 tons of 42 ½ pct Fe magnetite ore, to yield 5760 tons per day of agglomerated iron concentrates averaging 65 pct Fe. Located about 14 miles south of Reading, the property is ideally situated in relation to good highways and railroad. Three major steel plants, at Bethlehem, Steelton, and Sparrows Point, Md., are about equidistant from the mine. Discovery of the orebody resulted from an airborne magnetometer survey, completed in 1948, con¬sisting of 7000 lineal miles of flight lines spaced one-fourth of a mile apart and extending from the Delaware River on the east to Gettysburg, Pa., on the west. After examining the magnetic maps, Bethlehem's geologists made limited surface traverses over the Grace mine and Warwick area to check the location, and realtors were engaged to purchase the desired properties over and adjacent to the area showing favorable indication of ore.

Jan 1, 1957

By Robert H. Richards

It has long been known to boiler makers and to the users of cylindrical pipes of many kinds that when a tube is exposed to internal fluid pressure the resolution of forces is such that the material of the walls of the tube is exposed to twice the stress in the direction tending to produce longitudinal rupture, as it is in the direction to produce circumferential fracture. By longitudinal fracture is meant the fracture by a rent parallel to the axis; by circumferential fracture is meant fracture by rents running round the cylinder. In consequence of this the makers of boilers always lay the fibre of their metal in direction round the boiler, and the same is true with the makers of gun-barrels. I have never seen any good and simple illustration of this law until I met with it in blowing glass. If a thin bubble of glass be blown out in a spherical form and then exploded it will be found that the particles tumble into totally irregular shapes, showing no special direction in the molecular structure of the material. If now a bubble of glass be blown out and so manipulated that it will take a cylindrical form (see accompanying illustration), and then be exploded, it will drop into ribbon-shaped pieces from end to end, and the only parts that will be found to differ from this form will be the two hemispherical ends which will remain whole, having a fringe of ribbons representing the line of their fracture from the cylinder. The main point of difference between this experiment and the

Jan 1, 1883

By Robert S. Shoemaker

Receiving the Richards Award is undoubtedly the most memorable event in my entire life. There should, however, be more names engraved on it. These are the names of men who were my teachers (but not all of the academic variety) and my friends, each of whom had a part in my ever continuing education and thus have a part of this award. There was Bill Caldwell who made me into a chemist, and Will Shorey who added a lot of ore dressing. There was Rush Spedden who put me to work in his minerals research lab, Joe Brennan who made me turn my research into plant practice, and Tom Meek who sent me all over the world on metallurgical jobs. Bob Cheatham and Abe Dor taught me to try to give the client what he needs rather than what he wants, while Ed Malouf and Casey Davis always gave their particular brand of advice at exactly the right time. And, lastly, there was Leo Abell and Frank McQuiston, both fine metallurgists and the best friends a man could have. In addition to those I have mentioned, there are literally scores of others I would like to acknowledge with my sincere appreciation.

Jan 6, 1974

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paper. The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal.

Jan 1, 1960

By T. A. Rickard

The lodes of Cripple Creek, Colo., partake of the composition of the geological formation which they traverse. The prevailing rocks are andesitic breccia, lying upon granite, and also bodies of phonolite, trachytic phonolite, nepheline-basalt, etc., penetrating both the granite and the breccia. At Kalgoorlie, in West Australia, the prevailing rock is schistose, and has not been certainly identified, though microscopic sections indicate the probability that it was originally an acid eruptive. The lodes are essentially bands, more highly schistose than the encasing rock, and impregnated to a notable degree with disseminated pyrites and secondary calcite. During 1899 Cripple Creek produced 425,590 tons of ore, having a gross value of $15,658,254; during the same period the output of Kalgoorlie was 467,048 tons, valued at $17,724,587. In chemical composition, the ores at Cripple Creek and Kalgoorlie, respectively, present differences equally interesting to the petrographer and the metallurgist. In both cases we have to deal with altered eruptives as the matrix of the ore; but the much older rock of Kalgoorlie has undergone more decompo-

Jan 1, 1901

By A. C. Fieldner, F. H. Gibson, W. A. Selvig

A foRmer paper1 described in detail various methods of calculating coal analyses to obtain the composition and calorific value of the pure coal substance—that is, of the coal free from its mineral matter. The paper included a table showing calorific values of pure coal, as calculated from float-and-sink portions, by means of the Parr formula for "unit coal" and by the customary moisture-free and ash-free formula. A modification of the Parr formula was proposed, based on the assumption that one-half the sulfur present in Coal occurs as pyritic sulfur and one-half as organic sulfur. In the published discussion of the paper Cady gave a table of results on a large number of Illinois coals as obtained by the Parr formula and the proposed modification thereof. The results obtained by Cady indicate that the Parr formula applies better to Illinois coals than does the modified formula proposed by Fieldner and Selvig. The present paper gives results obtained by applying the modified Parr formula to the analyses of the float-and-sink portions of the coals shown in the former paper, and results obtained by applying the Parr formula, the modified Parr formula, and the simple moisture-free and ash-free formula to various coals of the United States ranging in sulfur content from less than 1 per cent to more than 4 per cent sulfur. A graphic method of estimating the calorific value of pure coal and determining the relation of the coal ash to the mineral matter of coal, as proposed by Stansfield and Sutherland,2 was applied to a number of coals, and the results are given herein. Testing Formulas with Float-and-sink Separations The former paper by Fieldner and Selvig gave heat values of pure coal of the float-and-sink portions of 21 coals, as calculated by the Parr formula

Jan 1, 1932

By A. J. Opinsky

THE purpose of this note is to indicate the locations and sizes of various interstitial holes in the orthorhombic uranium lattice based on a hard-sphere model. First, plane configurations of three and four atoms will be examined, and then the true interstices surrounded by four atoms in space and by five atoms in space will be obtained. The data and notation contained in a report by Tucker' will be used. Plane Configurations Fig. 1 presents the orthorhombic uranium lattice made of spheres touching at the closest interatomic distance. The three light-colored spheres in the ab plane are illustrative of the first type of configuration to be examined. If one edge of the unit cell is taken as the origin, the three atoms can be represented by the vectors [Oi + Oj + Ok], [ai + Oj + Ok] and [(a/2)i + (b/2)j + Ok] where i, j, and k are respectively parallel to a, b, and c. In the future, this notation will be shortened to [000], [a00] and [a/2 b/2 0], respectively. A vector R = [r s t] de-scribes the position of the hole surrounded by the atoms. Since the center of the hole must be equidistant from the three atoms R2 = r2 + s2 + t2 = (r-a)2 + s2 + t2 = (r-a/2)2 + (s-b/2)2 + t2. R = [a/2 (b/4) - (a2/4b) 0] is the solution of these

Jan 1, 1955

By John D. MacFadyen

Subject paper unfortunately has some serious flaws negating the usefulness of the paper. The authors claim that sulfur is the major source of production problems in cement kilns. This is not the case. Sulfur is not a problem as long as the mole ratio of sulfur to alkali oxides is less than, or equal to, 1. This is attributed to the sulfur preferentially combining with the alkali oxides and not acting as a clogging agent due to the nature of the pre-heater vessels. Where the mole ratio exceeds 1, many methods are avail- able to eliminate or reduce the clogging problems such as using the preheater bypass or a precalciner with up to 100% kiln gas bypass. In non-preheater kilns, the presence of sulfates is hardly ever a problem anyhow. Thus, the level of sulfur in the fuel and raw material that might cause problems is not a fixed amount, but is predictable. The purpose of the paper is to discuss the economics of conversion of kilns in the Indonesian and Phillippine cement industries from oil firing to coal firing. This economic analysis has very little to do with the sulfur levels. Thus, the section of the paper on sulfates is actually rather meaningless. The economic analysis is also rather meaningless because the authors have failed to follow accepted economic analysis procedures by including interest charges. They have fallen into the trap of confusing financing with economic evaluation. When the accepted methods of economic evaluation are used, the return on investment increases to about 35%. In conclusion, the paper is not a meaningful contribution, and sadly, quite erroneous.

Jan 1, 1983

By Thomas Crowe

Much has been written upon the precipitation of metals from cya-nide solution by zinc. We often read of the many factors that influence precipitation, such as zinc surface, purity of zinc, percentage of lead, temperature of solutions, strength of solutions in cyanide or alkali, etc. Little do we hear, however, of the part that oxygen plays in precipitation. Caldecott1 says: "As the dissolving of gold is essentially an oxidation process, so its precipitation is one of reduction." All who have studied or worked with cyanide solutions will agree that Caldecott's statement is true. In the cyanide work in the mills of the Portland Gold Mining. Co., we have always found oxygen to be the greatest enemy to precipitation. OXYGEN ANTAGONISTIC TO GOOD PRECIPITATION A few years ago, while making some experiments on the effect of pressure upon the dissolving rate of gold front our ores, to prove a point, I made some bottle tests under vacuum. The results were surprising, and showed that under vacuum practically no gold dissolved, which confirmed my belief that Elsner's equation was true and also led me to investigate the amount of dissolved air carried by solutions at atmos-pheric pressure. The experiment consisted in partly filling an acid-bottle with mill-solution and connecting it by a rubber hose to a vacuum pump. When the vacuum was suddenly applied, a cloud composed of. thousands of small air bubbles rose out of the solution, showing qualitatveily the . amount of dissolved air that was contained in the solution, and also proving that the relief of atmospheric pressure on the solution permitted this dissolved air to escape.

Jan 8, 1918

By AIME AIME

CHARLES ALLEN GIBBONS has been in the anthracite industry now since 1931, following his earlier experience in the bituminous fields, which dated from boyhood. In fact he was born in a coal-mining district-at Morgantown, W. Va.-starting at an early age working in the neighboring mines-going to the secondary schools there and then to West Virginia University. After graduating in 1923 with a B.S. in mining engineering he was made assistant superintendent of bituminous mines in southern West Virginia. Less than a

Jan 1, 1939

By A. E. Gorum, I. Cornet

Fatigrle of ionic crystals has been studied primarily in magnesinm oxide. under cyclic stress dislocations move irrreversibly; they multiply; slip bands form and grow; cracks mucleate and propagnte, and failure occurs. The use of ionic crystals such as MgO is advantageorus in such investigations because they are optically transparent. Individual dislocation Intersections with {100} surfaces may be observed with a standard microscope, using etch-pit techniques. Slip, deformation, crack .formation, and fracture in MgO crystals under cyclic stress are compared with cotrresponditzg processes in metals. ThE effect of cyclic loading in metals has been studied for many years. The appearance of slip lines is readily observed and the ensuing fracture may also be seen. From these observations it is possible to predict the behavior of a material and make an educated guess as to what is happening internally, but the actual changes taking place within the structure are not readily apparent. If one could obtain a material in which the individual glide components could be observed, it would be invaluable in determining the actual slip distribution resulting from cyclic loading as well as the distribution of slip in the neighborhood of a growing crack. Such a material is magnesium oxide. Dislocation arrays may be observed by means of etch pits

Jan 1, 1961

Bureau of Economic Geology, The University of Texas, Austin, Texas. E H Sellards, Director. A price list of publications will be sent upon request. The following is a selected list of Bulletins available, taking first those describing the geology and mineral resources of a particular area in Texas, as noted: Bulletin 1750, Camp Bowie and vicinity (1917), 50 cents, 1816, Runnels County (1918), 40 cents, 1818, Dallas County (1918), 50 cents; 1850, Coke County (1920), 50 cents, 1860, Medina County (1920), 50 cents, 1869, East Texas (1919), $1; 1931, Tarrant County (1920), 50 cents; 1932, Bexar County (1920), 50 cents, 2229, Johnson County (1922), 40 cents, 2330, Potter County (1924), 50 cents, 2333, Colorado County (1924), 50 cents; 2340, McLennan County (1924), 40 cents; 2544, Denton County, $1, 2607, San Angelo formation and Foard County, 50 cents, 2710, Cooke County, 75 cents; 2738, Ft Stockton Quadrangle, 75 cents, 2807, Tom Greene County, 50 cents, 3038, Geology of the Glass Mountains, pt 1, $2 50, 3027, Stonewall County, 50 cents, 3016, Bell County, $1, Mineral resources of Williamson County, 25 cents; Mineral resources of Travis County, 25 cents, Mineral resources of Uvalde, Zavala and Maverick counties, 50 cents, 3125, Grayson County, 50 cents Bulletin 3232, The geology of Texas, vol 1, Stratigraphy, including a bibliography, is in press Other Bulletins of particular interest: Bulletin 3101, Contributions to geology (1931), $1, 3138, Underground waters and subsurface temperatures in the Woodbine Sand of northeast Texas, $1, 2801, Contributions to geology (1928), $1, 2901, Contributions to geology (1929), $1; 3001, Contributions to geology (1930), $1; 1725, Texas granites (1917), 50 cents, 1849, On the underground position of the Ellenburger formation in north-central Texas (1920), 25 cents; 2234, Report on Texas alkali lakes (1923), 40 cents; 2239, The producing horizon in the Rios well in Caldwell County (1922), 25 cents; 2346, Report on oil and gas possibilities of the University Block 46 in Culberson County (1924) 10 cents; 2539, The Lytton Springs oil field, 50 cents, 363, The deep boring at Spur, 75 cents, 2703, Microscopic

Jan 1, 1933

By D. Harrington

TheRe has been, during the past year, a wealth of report data and discussion relating directly or indirectly to various phases of ventilation of metal mines, and many of the data are from foreign sources. The phase of the subject most generously accorded the attention of the technical press is that of cooling mine air, with much less attention to other fairly intimately associated features such as fan performance, friction factors, fires, mine gases, mine lighting, health of miners, and ventilation standards. Cooling Mine Air South Africa, with its very deep mining on the Rand and with fairly high working temperatures, 'contributes the most definite data on the subject of cooling mine air, and undoubtedly the most interesting issued are those from a paper by J. H. Dobson,' in which he gives a comprehensive review of the subject as gleaned largely by analyzing the data in three papers.2 Dr. Dobson's summation is decidedly interesting. In general it is recognized that the introducing into the mine and circulating to the working places of large volumes of pure air is the most effective method of giving deep, hot metal-mine workings reasonably efficient working conditions. A tabulation as to the cost of securing various amounts of cooling by circulating various volumes, from 230,000 to 760,000 cu. ft. per min., indicates that there are cost limits beyond which increase of quantity of air in circulation is impracticable, as the annual cost of circulating 230,000 cu. ft. of air per min. in a certain mine at a depth of

Jan 1, 1928

By E. P. Jennings

The iron-ore deposits of Iron county, Utah, which rival those of Lake Superior in extent, are situated 275 miles south of Salt Lake City, and 25 miles south of Lund, a station on the San Pedro, Los Angeles & Salt Lake railroad. The range of hills containing the deposits has a general NE-SW. strike, and rise from a few hundred to 2,000 ft. above the Escalante desert, the ore being included in an area of 5 by 20 miles. The basal rock of these hills is diorite-porphyry. The flanks of the range are covered with limestone supposed to be of Carboniferous age, underlain in some localities by quartzite. Both formations are conformable to the porphyry, and are the remnants of beds that formerly covered the highest peaks, but have been removed subsequently by erosion. In the central and southern parts of the range, beds of Cretaceous sandstone rest unconformably on the eruptives. Rhyolite-flows occur to the south and southeast of the iron-ore deposits; and dikes and sheets of post-Tertiary lava are common. With the exception of a few springs, the range is destitute of water. Sage-brush, stunted cedars and the common desert-bushes constitute the only vegetation. Large beds of coal of poor quality occur in Cretaceous sandstones 15 miles east of the ore-deposits.

Jan 1, 1905

By Paul Billingsley

The Georgetown mining district is located in Deerlodge county, Mont., about 20 miles west of Anaconda. It lies along the divide between the headwaters of Warm Springs creek, draining eastward, and Flint creek, flowing west and north through the Philipsburg valley. The actual divide is formed by Cable mountain, a narrow ridge running north and south, terminating to the south in low hills overlooking Georgetown lake, and to the north in a high, rugged plateau that falls off to the west to the wide valley of Flint creek. On the eastern, or Warm Springs, slope of Cable mountain is the Cable mine, with the Hidden Lake mine a few miles north. On the western slope is the Southern Cross group, with smaller mines, the Twilight, Cincinnati, Red Lion, and Big Bill, at intervals to the northward. The Georgetown mines lie in the hills south of Cable mountain; the Philipsburg mines, of which the Granite Mountain, Bimetallic, Hope, and Trout are the chief, form a separate group to the north, overlooking Flint Creek valley and Philipsburg. (See Fig. 1.) The region ranges in elevation from 5,000 to 9,000 ft. It is, with the exception of the lower valleys, well timbered with small fir and pine, although Cable mountain and the higher summits to the northward rise slightly above timber line. The main valleys have the smooth contours of glaciation, and their mouths are frequently choked with morainal deposits. General Geology. In a very general way the valley of Flint creek coincides in this region with the boundary between the pre-Cambrian slates of western Montana and the folded Palaeozoic rocks of the Rocky Mountain system. The great limestone formations of the Carboniferous and Devonian, lying at flat dips, extend from Anaconda well toward the head of Warm Springs creek, but on the divide the Cambrian appears, closely folded and intruded

Jan 1, 1914