Search Documents

Long pipelines handling suspended solids find wide use throughout the mining industry. In phosphate, iron ore, and clay mining; in hydraulic stripping of overburden; in tailing disposal; and in transferring concentrates between plants pipeline transport may prove cheapest material handling method. One drawback is necessity for providing attendance at booster stations, both for control and for protection of pumping equipment from sudden surges and failures. Thiele Kaolin Co. in Georgia has come up with an installation where instrumentation does this job automatically, efficiently, and economically.

Jun 1, 1955

By John M. Pitt

A rapid in situ stress measurement technique was developed for exposed underground surfaces. The method applies radial stress in small diameter (38mm) boreholes, initiating fracture propagation which is monitored by measuring ultrasonic pulse velocity. Theoretical relations for stress concentrations near boreholes provide independent expressions for unknown principal field stresses at incipient fracture; fracture orientation defines principal stress orientation. Accuracy and precision were evaluated using blocks of brittle material subjected to known stresses. Results were comparable to those obtained by other in situ stress measurement techniques.

Jan 1, 1984

By Bahrein Petroleum Company

In Comodoro Rivadavia, well 8. 132, drilled in zone No. 2, has discovered between 5205 and 5297 ft., the dcepest pool yct found in this field. The oil production in Bahrein for the year 1939 totaled 7,588,554 bbl., a decline of 709,444 bbl. from the 1939 production of 8,297,998 bbl. The production for the first seven months of 1939 remained fairly constant, the daily average by months during this period ranging between 20,000 and 22,000 bbl. per day. The daily average rose in August to the year's high of 23,800 bbl. per day, then dropped gradually to the year's low of 18,787 bbl. per day for November. The daily average for the year was 20,791 bbl. At the end of 1939 there were 59 wells producing and 8 wells drilling.

Jan 1, 1940

By Bahrein Petroleum Company

In Comodoro Rivadavia, well 8. 132, drilled in zone No. 2, has discovered between 5205 and 5297 ft., the dcepest pool yct found in this field. The oil production in Bahrein for the year 1939 totaled 7,588,554 bbl., a decline of 709,444 bbl. from the 1939 production of 8,297,998 bbl. The production for the first seven months of 1939 remained fairly constant, the daily average by months during this period ranging between 20,000 and 22,000 bbl. per day. The daily average rose in August to the year's high of 23,800 bbl. per day, then dropped gradually to the year's low of 18,787 bbl. per day for November. The daily average for the year was 20,791 bbl. At the end of 1939 there were 59 wells producing and 8 wells drilling.

Jan 1, 1940

By F. C. Blare

THE best method for the estimation of copper in ores and secondary products is that proposed by Dr. Steinbeck* for the award offered by the Mansfeld'schen Ober-Berg-und Hutten-Direction. It is based upon the decolorization of the blue ammonia solution of copper by potassic cyanide,† It is necessary for the accurate estimation of copper in arsenides that the arsenic be separated from the copper before the ammonia solution is made. The presence of a notable amount of arsenic renders the titration by potassic cyanide inaccurate, the end reaction being obscured by the appearance of a yellowish-green tint towards the end of the titration. The change of the color of the ammonia solution from blue to the tint caused by the presence of arsenic cannot be used for an end reaction, for the intensity and quick appearance of the latter-color depend upon the amount of arsenic present in the solution. In the analysis of speise, the method of separating the copper by an oxidizing and reducing treatment in the muffle, to volatilize the arsenic, gives poor results, and there may easily be some loss of the weighed sample. The separation of the precipitated sulphides of arsenic and copper by treating with sodic sulphide, gives good results, but the process is tedious. I have used the two following methods, which are simpler and more expeditious than those mentioned, with good results. * Fresenius, Zeitschrift Air Anal. Chemie., viii, 1. †First noted by Parkes in the Mining Journal for 1861.

Jan 1, 1881

By W. M. Pierce

CORRUGATED sheet zinc has been used abroad for a great many years as a roofing material. In this country it has been in use for about 10 years. From the outset it was recognized that zinc sheets required closer spacing of the supporting purlins than steel sheets. Exact data regarding safe maximum fiber stresses were not available, however, and on occasions the span used was excessive and the sheets sagged. This paper describes both service and laboratory tests to determine safe maximum fiber-stress values for various grades of zinc for use in calculating the proper purlin spacings for any gage and profile under given loading conditions. These tests consist of laboratory loading tests on full-size roof sections over extended periods of time; of actual roof installations erected in conformity with the indications of the laboratory tests and observed over a period of years; of careful determinations of the apparent elastic limit of several grades of zinc, and finally of static tests1 (so-called creep tests) to determine the rate of flow of zinc under a variety of static tensile stresses at definite temperatures. Certain of the individual tests extended over a period of more than two years.

Jan 1, 1929

By F. H. Buchella

When Duval Sulphur & Potash Co. awarded pre- mining stripping and early mining at Esperanza to an independent contractor, it was agreed that monthly payments for excavation were to be made on a truck count. At six-month intervals, however, adjustments must be made on the basis of actual excavation or cut from the pit area. It was estimated that it would be three times more expensive to have the pit sectioned by chain and transit survey than to use photogrammetry, since it would take two crews of three men approximately two weeks to do the field work, another two weeks to plot the sections, and additional time to establish a control network. Therefore it was agreed to have the mine area mapped by photogrammetry for both the premined surface and for semi-annual check surveys necessary for intermediate settlements. A triangulation net was established with a maximum distance of 900 ft between control points. In about 30 working days a two-man survey crew, using a theodolite, set up and triangulated 30 stations and calculated their results. For ease in spotting on the photographs, control stations were marked on the ground with white-painted tires centered over the survey pins.

Jan 6, 1960

By Richard Klimpel

In this paper various formulae are developed which can be used to estimate stream flow rates or weight ratios given information on the stream components. The type and level of experimental error present in the stream component analyses does have an important bearing on the numerical values (and reliability) of the weight ratios calculated by the various formulae. A simple but theoretically sound method is shown for selecting appropriate estimation formulae for any given engineering operation. The derived formulae are applied to sets of experimental classification data for illustration purposes.

Jan 1, 1980

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated: "Whereas, the American Institute of Mining and Metallurgical Engineers is organized for purely professional and scientific purposes, and whereas diversity of opinion among its members on partisan or political questions is inevitable, it is the expressed policy of the Institute to refrain from official participation or action, in political and semi-political matters." AND WHEREAS, appeals for additional advice have been received: NOW, THEREFORE, IT IS RE¬SOLVED: (1) That the policy of the Institute is to refrain from official participation or action in controversial non-technical economic subjects; further (2) That if any Local Section is in doubt as to the application of this policy to any particular subject, it should communicate with the Secretary of the Institute for advice.

Jan 1, 1946

By J. A. Herbst, G. E. Agar

Beginning with the second paragraph in the second column of page 148, this paper should read: The Reynolds number in Fig. 6 was calculated from the inlet diam and it is evident from the graph that above NR = 5000 the value of K2 is as it should be, a constant. The data10 shown in Fig. 7 was obtained for fluids flowing in pipes of diam D with sharp edged orifices of diam d. To be consistent with the representation in Fig. 6 the Reynolds number was calculated with the orifice diam d. These two sets of data show similar patterns and the variation in the orifice coefficient C is believed to account for the variability of the cyclone coefficient K2. The values of C given in Table IV are derived from K2 by conversion of units. C more nearly represents an equivalent orifice coefficient for a cyclone. Armstrong1' showed that data reported by Chaston 12 and Elcox13 yielded values for C of 0.24 and 0.27, re- spectively, Dahlstrom's4 data gives a value of 0.22. As a consequence of the variability of the cyclone coefficient some caution must be exercised in substituting for Q in the split size equation.

Jan 1, 1967

By G. St. J. Perrott

ONE of the important hazards in coal mining is the danger of ignition of explosive mixtures of methane and air or coal dust and air, or both, by the explosives used in blasting the coal. It has long been recognized that certain explosives are more dangerous than others in this respect. In America and abroad, government testing stations have been established for officially passing on the suitability of explosives for use in coal mines. In this country the Federal government is given no power to enforce the use of the approved explosives but merely publishes from time to time, through the Bureau of Mines, those explosives which have passed the tests necessary to place them on the list for use in coal mines. In spite of this lack of police power, the increase in the use of permissible explosives since the promulgation of the first list in 1909 has been rapid. In 1912, only 8 per cent. of the explosives used in coal mines were permissible; in 1925, this figure had increased to 25 per cent. While the past record of permissible explosives has been most gratifying, it is very desirable that we pave the way for further improvement in explosives and blasting methods by learning more about the mechanism of ignition of gas and coal dust by explosives. To this end a considerable amount of investigative work already has been carried out and a large amount yet remains to be done. It is the purpose of this paper to discuss briefly the effect of the characteristics of explosives and method of loading in the borehole on the liability of a blown-out shot to ignite explosive mixtures of gas or dust. For an account of the methods by which an explosive is tested for permissibility for use in coal mines, the reader is referred to Schedule 17-A of the U. S. Bureau of Mines.

Jan 10, 1926

By Orville R. Lyons

THE continuous vacuum filter, whether it be a vertical or horizontal disk, inside or outside drum, when properly applied is a very effective device for dewatering fine solids. Because of the number of variables that affect its performance, however, it is not possible to obtain consistently maximum moisture reduction in an operating plant. This paper presents a method for determining the average cake moisture and the variations in cake moisture to be anticipated when dewatering fine solids by continuous vacuum filters under normal operating conditions. Previous investigators1,2 have found that certain factors influence filter performance, drum or disk diameter, speed of rotation, percentage of immersion, and the percentage of solids in the feed influence capacity. Blinding of the filter cloth reduces effective vacuum, produces a wetter cake, and may decrease capacity. Reduced vacuum or improper adjustment between vacuum and blowing portions of the cycle will produce a wetter cake and also may decrease capacity. Widely fluctuating feed tonnages will adversely affect cake moisture and capacity. Flocculation, when properly applied, increases capacity and reduces cake moisture. Without flocculation, the slimes are the first particles sucked to the filter medium, which becomes partially blinded in consequence. With flocculation, the flocs act as coarse particles and the filter medium is not blinded. Overflocculated pulps, although filtering well, may yield wet cakes. Average Particle Size and Cake Moisture A method for predetermining the surface moisture content of coal filter cakes was published in 1949; but this method could not be applied to coals deficient in —200 mesh material or to fine mineral concentrates. Test data obtained for geared-weight types of vibrating screens4 and for centrifuges5 used to de-water coal provided definite correlations between the average particle size of a dewatered cake and the surface moisture content of the cake. It was thought that this same method of correlation should be applicable to filters, whether dewatering fine coal or fine mineral concentrates. To develop a correlation or correlations between average size of cake and cake moisture, the author collected data for filtration operations from as many sources as possible. In a considerable number of instances the information was provided by plant preparation engineers,"-" a few of the tests were on a laboratory scale: and the remainder of the data was obtained from published articles.10-17 Table I contains size-consist and miscellaneous data for coal filter cakes, and Table II contains the same data for mineral concentrate filter cakes. Fig. 1 shows the relationships existing between the average particle size of the cake and cake moisture (surface moisture for coal and total moisture for minerals) when dewatering fine solids by a variety of makes and types of filters. Average particle size is calculated by averaging the linear openings of the various pairs of screens used in the screening test, weighted in accordance with the percentages of material in the various fractions.

Jan 1, 1952

By Herbert E. Hawkes

“For his Pioneering leadership in the science and technology of mineral exploration, especially in the development and world-wide application of geochemical methods as major exploration tools, and for his lecture ‘Geothermal Hydrogen’.”

Jan 1, 1981

Jan 1, 1940

University of Alabama University, Alabama Mining and Metallurgical Society Meets first and third Mondays each month JOHN MACLEOD MCKEE, President WILLIAM L. ALLMAN, Secretary J. R. CUDWORTH, Faculty Sponsor RICHARD L. BOWRON, Counselor University of Arizona Tucson, Arizona Millers' Society LA MONT WEST, President AL WALLACH, Secretary J. B. CUNNINGHAM, Faculty Sponsor B. R. HATCHES, Counselor

Jan 1, 1939

By N. M. Langdon

The calculation of slags may be considered under three cases: I. A certain percentage of silica is required, it being known, in a

Jan 1, 1893

Jan 1, 1940

Jan 1, 1961

By D. S. Fuerstenau, S. Chander

The results of a preliminary investigation undertaken to explore the possibility of treating potential in sulfide mineral flotation systems as an external variable are reported in this note. Two different methods were used to assess floatability. One involved measurement of contact angles at a mineral electrode in reagent solutions, and the other involved direct measurement of flotation recoveries in a Hallimond tube flotation cell that had been modified such that mineral particles were in electrical contact with a gold electrode. Fairly good correlation between the contact angles and flotation recoveries has been obtained.

Jan 1, 1976

By William E. Ford, Edward Salisbury Dana

I. Anhydrous Chlorides, Bromides, Iodides; Fluorides. II. OxycMorides ; Oxyfluorides. III. Hydrous Chlorides; Hydrous Fluorides. The Fourth Class includes the haloids, that is, the compounds with the halogen elements, chlorine, bromine, iodine, and also the less closely related fluorine.

Jan 1, 1922