Search Documents

By L. A. Hanson

Jan 1, 1964

By B. K. Asdell

Crude kaolin exhibits a wide particle size range in which kaolinite is the predominant mineral. Bene-ficiation by wet processing produces high-brightness white pigments. The wet processing techniques peculiar to kaolin beneficiation are emphasized in this article in some detail. Included are discussions of long-distance pipeline transportation, centrifuga-tion, flotation, spray drying and shipment as 70% solids slurry. Georgia, a state seldom considered to be an important mineral producer, has one surprising feature — it is the nation's largest producer of kaolin. Kaolin is a highly important raw material in the paper, rubber, ceramic whiteware, paint and chemical industries. In 1965, more than 2.7 million tons of kaolin were produced in this state, a 150,000-ton increase over the preceding year, and production continues to climb. Strictly defined, the term "kaolin" applies to a group of hydrous aluminum silicates in which kaolinite is the predominant mineral. Kaolinite is inherently white, non-abrasive, chemically inert, and of a very fine particle size, ranging from sub-micron to 40-microns equivalent spherical diameter. An electron-micrograph of kaolinite is shown in Fig. 1. The particles finer than about 2 microns are thin, elongated plates, hexagonal in outline. The larger particles, coarser than 2 microns, are predominantly vermicular in outline with a foliated structure. Table I shows a typical chemical analysis of commercial, wet-processed kaolin compared to pure kaolinite. The sedimentary Cretaceous deposits of the Coastal Plain are the source of most of the kaolin produced in the Southeast. These deposits are of relatively high purity, and it is not uncommon to find the clays running greater than 90% kaolinite. Beneficiating plants using wet processing techniques are most numerous in an area within about 50 miles east of Macon, Ga., in a band approximately 15 miles wide. Kaolin may vary widely in quality from one deposit to another, or within the same deposit. The qualities critically examined are brightness index as measured by reflectance, viscosity of water suspensions, bleachability and particle size distribution. Crude kaolin always contains sand and mica in varying amounts, along with small amounts of many other minerals. These are classed collectively as "grit" because; they are generally coarser than 325

Jan 1, 1968

By William E. Ford, Edward Salisbury Dana

The important BARITE GROUP is the only one among the anhydrous sulphates and chromates. Mascagnite. Ammonium sulphate, (NH4)2S0,. Orthorhomhic. Usrially in crusts and stalactitic forms. p = 1.523. Occurs about volcanoes, as at Etna, Vesuvlus, etc. Taylorite. 5K2SOa.(N&)ySOd. 111 small compact lumps or concretions. From the guano of the Chincha Islands. Thenardite. Anhydrous sodium sulphate, Na2S04. In orthorhombic crystals, pyrarnidal, short prismatic or tabnhr; also as twins (Fig. 384, p. 160). White, to brpwnish. 0 tically +. p = 1.477. Soluble in water. Often observed in connection with salt lates, as on the shores of Lake Balkhash, Central Asia; similarly elsewhere; also in South America in Tarapaca, Chilc. In the United States, forms extensive deposits on the Rio Verde, Aria. In Cal., at Borax Lake, San Bernardino Co. Aphthitaiite. Arranite. Glmerite. (Ii,Na)&O1. Rhombohedral; also massive, in crusts. Color white. From Vesuvius, upon lava; at DouglashaU near Weateregeln, Ger- many, in hloditc; Stassfurt, Germany; Rocalmuto, Sicily.

Jan 1, 1922

By Alan D. Smith

Mine roof fall characteristics of 250 falls in 5 different room-and-pillar coal mines, located in Pike, Martin, and Floyd counties, were investigated to determine the relationship of selected parameters associated with roof failure and the assumed condition of the mine roof before failure. The selected parameters used in the study included: presence of cracks and water before the occurrence of fall, sloughing of coal ribs, floor heave condition, type of roof support (resin or mechanical anchor bolts), distance to coal face, and time of occurrence of fall after initial coal extraction. In addition, research hypotheses, utilizing multiple linear regression techniques, were generated to test the relationship among the selected parameters and mine roof condition. The results indicated that the vast majority of falls portrayed some presence of water before the actual fall, occurred in less than 30 weeks after initial coal excavation, located usually greater than 30 meters from nearest coal face, gave evidence of cracks in mine roof before occurrence of fall, generally portrayed a good roof condition before the fall, showed presence of sloughing of coal ribs, and gave no occurrence of floor heave before occurrence of fall. In terms of the characteristics of the original support systems in the mine roof falls studied, most roofs were either supported by mechanical-anchor bolts or resin or full-column bolts; very rarely did the roof appear to fail if supported by posts or cribs. A detail inspection of the hypothesis and model comparison results gave supporting evidence that the condition of the roof is not dependent on the usual indicators of potential failure, such as presence of cracks and moisture. In fact, in most cases of mine roof failure, the immediate roof condition was rated as good or better, which gives little or no indication of pending failure and collapse. Hence, a combination of factors that are not easily accessible to measurement, are the dominant factors in the determination of roof fall-potential areas.

Jan 1, 1984

Jan 1, 1937

Jan 1, 1929

By C. A. Mezger

These districts are limited approximately on the north by the railroad from Salisbury to Ashville, and comprises the counties of Alexander, Catawba, Burke, Rutherford, McDowell, Cleveland, Lincoln, Polk and Henderson in North Carolina, and Greenville, Spartanburg, Union and York in South Carolina. The occurrence of monazite at Amelia Court House, in Virginia, belongs evidently to the same geological system, as its distance from the Alleghenies corresponds with that of the above-mentioned districts, and all the stratification runs parallel with those mountains.

Jan 1, 1896

Jan 2, 1951

By R. R. Estill

THE rank of the Ruhr coal ranges from a high volatile bituminous coal to an anthracite, depending to some extent on the original depth of the seam. The average Ruhr coal corresponds to a soft bituminous American coal of a coking quality. The average thicknesses of individual coal seams being mined are also comparable (59 in. against 65 in. in the United States). However, consideration of seam conditions and mining conditions other than those just mentioned emphasizes differences rather than similarities with United States soft coal. In general, the Ruhr seams now being mined are much more folded and inclined than American seams. Dips of 20" and 30" are common in seams now being worked, and 30 pct of the coal reserves in the district are in seams dipping more than 35". Only on the tops and bottoms of folds do we find rather flat coal seams. In addition to the folding there is extensive displacement by cross faulting plus a certain amount of strike faulting of an overthrust nature, which results locally in doubling or omission of seams. Because of the long history of mining in the Ruhr, nearly all coal lying near the surface has long since been mined out, and we find that the average depth of mining is at present about 2300 ft below the surface. Deep mining, folding, and faulting result in seam conditions requiring a great deal more roof support than one finds in American soft coal mines. In fact only in the anthracite district and the Rocky Mountain and Pacific coal fields do we find somewhat similar conditions. It is easy to say, therefore, that the problem of mechanization of coal cutting and loading in the German mines is quite different from that which we have so effectively met in America with our mobile cutters and loaders, duck bill loaders, and a room and pillar system of mining our drift and slope mines.

Jan 12, 1950

By T. L. Joseph

Sulfur balances calculated from operating data covering thirty-five blast furnaces indicate that approximately 92 per cent. of the total sulfur charged enters with the coke, 7 per cent. with the ore, and 1 per cent. with the stone.. Most of the sulfur is carried from the furnace by means of the slag, the total amount eliminated being the product of the slag volume and the percentage of sulfur it contains. Additional sulfur in the charge must be eliminated either by increasing the percentage of sulfur in the slag or the quantity of slag. From relations found between slag volume and coke consumption and sulfur in the coke and slag volume, curves have been prepared showing the relative value of blast-furnace coke as its sulfur varies from 1 per cent. CHARCOAL was the predominant blast-furnace fuel until 1838, when it was found, by the operation of a 2-ton experimental furnace, that anthracite could also be used. This information was a stimulus to the iron industry, particularly in eastern Pennsylvania where anthracite was available at low cost. The production of anthracite pig iron increased steadily and, in 1855, its tonnage exceeded that of charcoal iron. Of the 680 furnaces in operation in 1874, the 226 using anthracite produced nearly one-half the total tonnage. In 1869, the production of coke furnaces exceeded that of charcoal furnaces and, in 1875, coke surpassed anthracite as a metallurgical fuel. In 1907, the output of anthracite pig dropped well below a million tons and its present significance is largely historical. In recent years, the production of coke has gone hand in hand with the production of pig iron and it has gradually attained the position it now occupies as a universal blast-furnace fuel. Charcoal, however, has great merit as a blast-furnace fuel chiefly because of its freedom from ash and sulfur. The harmful effect of the latter and the necessity of keeping the percentage of this element in pig iron at a minimum are well recognized. Other contaminating elements can be reduced to specified limits in the steelmaking process, but the control of sulfur belongs essentially to the blast furnace. The purpose of this paper is to point out the distribution of this impurity in blast-furnace

Jan 9, 1924

Jan 1, 1941

Jan 1, 1941

Beall: Mr. Donovan, would you tell me something about your early life, leading up to your going into I he mining industry? Donovan: I was born in St. Charles, Minn., on November 18, 1879. At that time my father was a school teacher, but he later entered the Congregational ministry. He was pastor in several small Minnesota towns, so we moved about quite a bit.

Jan 8, 1966

By Wayne D. Gould, Terry O. Arney

The Pinto Valley digital control system is a supervisory system interfaced with a conventional analog control system. The design criteria, the hardware selection, and the startup of the system in the Pinto Valley concentrator are reported in depth. Examples of data collection application, as well as the present and immediate future implementation of control strategies, are discussed. This paper is a description of the digital data acquisition and control system that is installed at Cities Service's Pinto Valley concentrator.

Jan 1, 1978

Jan 1, 1913

By S. G. Malghan, J. P. Van Dillen

Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined.

Jan 1, 1984

By William M. Baldwin, T. S. Howald, A. W. Ross

EXPLORATORY WORK THE related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal [ ] strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strips-20.29 and, to a lesser extent, yield strength7,11,17 and stress-strain curves" have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between earing tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture, a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1945

By G. Sherburne Rogers

Introduction. ONE of the features of oil-field work that puzzles operator, chemist and geologist alike, is variation in the gravity of the petroleum produced, on neighboring leases or even from adjoining wells. Few fields in the United States yield oil that is of uniform gravity throughout; in some, fields the different grades are produced from different sands, in a few from different formations, and in many from different areas in the same sand. In a few cases, perhaps, a common assumption-that the heavier oil is derived from the lighter through the escape of the more volatile constituents-is valid, but many cases can not be explained in this way. Although in the California fields the specific gravity of the oil generally decreases with depth, there are numerous exceptions to this rule; and, as in many other regions the light oil is found nearest the surface, it is evident that evaporation underground is generally an unimportant factor. It is generally recognized that the great differences between petroleum from widely separated fields are due largely to differences in age and degree of metamorphism and to variation in the composition of the original organic matter; but in the writer's opinion some of these broader differences, as well as most of the minor variations in the character of the oil from any one field, are clue to the local action of natural reagents such as sulphur or oxygen. This is particularly likely to be true if the oil has migrated from one formation to another, as in the California fields; and in some areas it appears that variation in sulphur content may even afford a rough index of the extent or distance of the migration. It is the purpose of this paper to call attention to the chemical action of sulphur and oxygen on petroleum, to show that the gravity of the oil from any one field is intimately related to its sulphur content, and to discuss the possi-

Jan 7, 1917

By Henry H. Otto

The anthracite industry can be divided into two parts—the underground, or mining, and the outside, or preparation or manufacture. To understand recoveries in the two branches, some of the history of the industry and the changes that have taken place in the past century should be considered. It is a long step from 1807, when 55 tons were produced in the Wyoming field, to 1917, the peak year, when 80,841,223 tons were shipped to market from all the fields. In 1820, the Lehigh Coal Co., the predecessor of the Lehigh Coal & Navigation Co., shipped 365 tons in arks down the canal of the Lehigh Navigation Co. The Schuylkill field was not opened until 1822, when 1480 tons were shipped. The Wyoming field really became a producer in 1829, when 7000 tons were mined and shipped. It is well to note, at this time, the passing of the Coleraine colliery after a life of 88 years; in collieries of this age will be found the romance of the region, as well as the history of the changes to date. Mining Methods In the Lehigh region, the first coal came from the old quarry mines at Summit Hill; a little later the open-cut workings, or quarries, east of Jeansville, and near Beaver Meadow were opened. In the Wyoming field, it was necessary to resort to underground mining almost from the very first. Ashmead1 has described the changes in outside preparation methods, dl tending to increase the percentage of coal shipped to market. A description from the days when the lump coal was raked and screened out in the quarries or mines, to the modern breaker of today, shipping as high as 6000 tons of at least eight sizes of coal in an 8-hr. day is a very interesting story. Each size is a step toward increasing the yield from the property. With the belief that the supply was inexhaustible, the early mining was conducted with the thought of getting the maximum amount of coal on first mining. The superintendent was his own foreman and engineer.

Jan 1, 1925

By Alfred E. Hunt

Professor EGGERTZ first published a method based upon the fact that, when steel is dissolved in dilute nitric acid, and heated until the separated flocculent carbonaceous matter goes into the solution, the liquid assomed a brown color proportionate in intensity to the amount of the combined carbon in the steel. This method has been so variously modified that at present but few chemists use exactly the same procedure. It is the object of this paper to present

Jan 1, 1884