Search Documents

By R. M. Brown, W. J. Murphy, B. M. Kapadia

An investigatiott was conducted to study the influence of nitrogen, titanium, and zirconium on the boron llardenabilzty effect in a low-carbon constructiona2 alloy steel. The experimental steels investigated exhibited a significant variation in hardenability, the variation being dependent on the interactions of boron, titanium, and zirconium with the nitrogen. Only the boron not combined with nitrogen was effective in increasing hardenability. Titanium, and with lesser effectiveness zirconium, combined with available nitrogen, thereby protecting the boron. The hardenabil-ity effect mas related to an empirical expression for the "effective" boron content, P, deduced from experimental evidence of these interactions. The hardenabzlity effect reached a maximum at about 0.001 wt pct 0, and decreased somewhat as P increased further. The physical understanding of this relationship is discussed. FOR many years boron has been added to steels to obtain high hardenability. Although a great deal of research has been conducted on boron-treated steels, certain aspects of the boron hardenability effect have not been fully understood. For instance, the magnitude of the hardenability effect has been observed to vary markedly, depending on the steelmaking technique, even when the amount of boron in the steel was essentially constant. Furthermore, the optimum amount of this element to be added has not been definitely established. A better understanding of the boron hardenability effect is essential because too small an addition of boron is likely to be ineffective, while an excessive amount can cause brittleness'' and hot shortness. The findings of earlier investigations have shown that the hardenability effect cannot be consistently related to the amount of boron added or retained in the steel. Grossmann observed that in a 0.60 pct C steel the hardenability increased to a maximum with mold additions up to about 0.0025 pct B and then decreased with larger additions. Other investigators5 likewise reported a maximum in the hardenability at about 0.003 pct B. Crafts and Lamont, however, found that in commercial open-hearth heats of medium-carbon steel the hardenability increased linearly with boron up to 0.001 pct and remained essentially unchanged with larger percentages up to 0.006 pct. Other investigators7,' also observed a rather constant hardenability effect in the range about 0.0005 to 0.0035 pct B. These observations and other evidence suggest that the effectiveness of boron in increasing hardenability probably depends, in addition to the amount, on the form of boron retained in the steel, this form being influenced by the presence of other elements. Both oxygen and nitrogen apparently exert the strongest influence on the hardenability behavior, since, at the temperature of liquid steel, boron readily combines with these elements, thereby losing its effectiveness as most experimental evidence seems to indicate. For consistent recovery of the boron effective in increasing hardenability, it is necessary that the oxygen and nitrogen in the steel be either reduced to extremely small amounts by the steelmaking practice or neutralized by combination with other elements before the addition of boron. The importance of achieving adequate deoxidation prior to the addition of boron in order to realize the full hardenability effect of boron has been sufficiently emphasized by earlier investigators. Digges and Reinhart' and others have investigated the role of nitrogen and have shown that nitrogen also interacts with boron and reduces or nullifies altogether its effect on hardenability. Moreover, their work also demonstrated that the addition of strong nitride formers such as titanium and zirconium reduce the deleterious effect of nitrogen on boron hardenability by combining with nitrogen to form stable nitrides. Another element which has a pronounced influence on the boron hardenability effect is carbon. It has been shown7'10 that the hardenability effect of boron diminishes with increasing carbon content, and becomes almost negligible at the eutectoid composition. This observation is useful in comparing the potential increase in hardenability from boron of steels with different carbon contents, but is not relevant to a study of the effects of normal steelmaking variables. The amounts of oxygen and nitrogen in steel vary with the steel composition and steelmaking practice employed. Most commercia1 low-alloy steels are fully deoxidized by the addition of silicon and aluminum, or other strong deoxidizers, which adequately protect the boron from oxidation. In addition, one or more of the elements such as titanium or zirconium are usually added, either separately or in combination with boron, in the form of complex ferroalloys, to protect boron from combination with nitrogen in the steel. However, the actual amount and type of addition employed for a given processing requirement are usually selected by trial and error, and have a rather limited range of applicability. As a result, substantial variations in the hardenability of boron-treated steels are often observed in practice, particularly when the nitrogen content of the steel is a significant processing variable. These variations might therefore be reasonably attributed to the interactions between boron, nitrogen, and titanium or zirconium present in the

Jan 1, 1969

By Stuart A. Bengson

It is extremely difficult to revegetate disturbed sites and mineral wastes in an arid environment because of sporadic and undependable rainfall. Thus, irrigation is often a must for starting seed germination and vegetation. Quite aside from the harsh climate, mining disturbances by themselves cause various adverse conditions for a revegetation program. The problems of revegetating a harsh soil, for instance, are often compounded by the steep slopes of mine wastes. Since these steep slopes intensify the droughty conditions by rapidly draining away soil moisture and accelerating runoff, supplemental irrigation may be the only solution for establishing vegetative cover on the slope.

Jan 8, 1976

By A. F. Daily

Free World consumption of diamonds of all types closely follows the fluctuations of the business cycles in the large industrialized countries, particularly the U.S. Sustained purchasing by this country for stockpiling purposes has been a major factor in Free World demand for crushing bort and industrial diamonds, and it has been for this reason that investments in larger plants have been made by all major diamond mining companies during the past few years. For the purposes of this study, the diamonds produced in the Congo and elsewhere in the Free World are divided into three types:

Jan 5, 1961

Frank L. Bader has been appointed to the sales staff of Lehigh Navigation Coal Co. in the Philadelphia territory. H. C. Burrell, former coordinator of raw materials, Pittsburgh, Penna., has been made manager of raw materials for Columbia-Geneva Div. of U. S. Steel Co., San Francisco. J. H. Cazier has resigned as general superintendent of Bagdad Copper Corp., Bagdad, Ariz., to devote full time with E. A. Scholz to the operation of the Copper King, Phillips and Black Pearl Mines near Bagdad. They have operated the Copper King zinc mine for more than two years.. Production started from the Black Pearl and Phillips tungsten mines during the past year. Robert T. Chapman has resigned from Reynolds Mining Corp. to join Westmoreland Manganese Corp. as general superintendent. Annan Cook, with Kennecott Copper Corp.'s exploration dept. for the past three years, has been appointed district geologist for the eastern states.

Jan 1, 1952

By Richard Conkling

A SHALE layer, buried beneath two or three thousand feet of strata, in some instances, will upon folding become thicker in the synclines and thinner on top of the anticlines. This can be accounted for, in part, by the stretching on the crests of the fold and the compressing in the troughs; but this will by no, means account for all of it, as is shown in the example herein set forth. It is my firm belief that the rest of the thickness is due to flow. What causes the movement, however, does not concern us here, so long as there is movement, for this article purposes to show its effect upon the producing area of different sands. It is the author's hope, in this way, to drop a hint or two that may be valuable to the oil geologist, in making estimates of future productions and values of oil properties. An example will be given from property in the famous Cushing Pool in northeastern Oklahoma, where the author has had occasion to make a detailed study before recommending some property to his company, and has then been able to watch the results of this work. The author never mapped the surface structure in this pool, as this had been done by Frank Buttram when he was with the Oklahoma Geological Survey. We are using, therefore, a section of his map in this article for our surface contours. The main east clip comes farther east than this section shows.

Jan 10, 1916

By Ian Wark

MERCAPTOBENZTHIAZOLE and its sodium salt are marketed under the trade names Flotagen and Flotagen S respectively, for use as collectors for cerussite and other minerals. The structural formulas for sodium mercaptobenzthiazole and for sodium ethyl xanthate are: Chemically there is a resemblance between the two compounds, though the free acid (mercaptobenzthiazole itself) is much more stable than xanthic acid. Both are readily oxidized, e.g., by iodine to disulphides, and can be estimated by iodometric titration. Qualitatively they are similar as collectors in flotation, although there are quantitative differences between them that may be important in practice. It is deduced that the influence of the nitrogen atom is subordinated to that of the sulphur atoms, and that the dominant group of these compounds is the mercapto group -SH or -SNa. The general method of investigation has been based on contact tests. Two temperatures, 10° and 35° C., have been chosen, and with a standard concentration of 20 mg. per liter of mercaptobenzthiazole (i.e., of the free acid) the influence of alkali, cyanide and copper sulphate on contact at sulphide mineral surfaces has been studied. This standard concentration corresponds to about 19 mg. per liter potassium ethyl xanthate; it brings out the differences between the minerals better than a higher concentra-

Jan 1, 1939

By R. G. Stickney

INTRODUCTION The Basalt Waste Isolation Project, conducted by Rockwell Hanford Operations under contract to the U.S. Department of Energy, is assessing the feasibility of the disposal of commercial radioactive spent fuel/high-level waste in deep geologic formations in basalts beneath and within the Hanford Site in southeastern Washington State. The Basalt Waste Isolation Project mission is to identify and characterize a potential geologic repository site in basalt and to develop associated facilities and technology required for the potential permanent isolation of radioactive wastes in basalt formations. In support of the Basalt Waste Isolation Project, a laboratory testing program was conducted to evaluate the performance of the Council for Scientific and Industrial Research's "Doorstopper" biaxial strain cell. To support site characterization studies and the design of repository openings, in situ stress measurements will be conducted within the reference repository horizon (~970 m). The Doorstopper is one of the instruments being considered for use in these measurements. It was selected because it requires only a small volume of work to achieve stress relief, which is important in a closely jointed basalt. Also, test durations are short, permitting a large number of measurements to be made within a given time to increase confidence in the results. Within the reference repository horizon, temperatures are expected in the range of 40º to 60°C with a humidity of up to 100%. For this testing program, test conditions were selected to closely resemble those expected within the repository horizon. The Doorstopper test, mainly developed by Leeman (1964), is a strain rosette relief method of measuring rock stress in situ. The Doorstopper consists of a four element, 45º strain gage rosette

Jan 1, 1984

By J. M. Morkowitr

A. Sawatzky (Atomic Energy of Canada, Ltd.)—The detailed criticism by Markowitz of my simple treatment of the thermal diffusion of hydrogen in Zircaloy-2 indicates that my paper was not as lucidly written as it could have been. I would therefore like to reiterate several of the main points of my proposed mechanism and describe in more detail some of the features only implied in the original paper. The distribution equation derived in my paper was stated to hold only for the case where the volume taken up by the hydride was small compared to the volume taken up by the solid solution phase, subsequent work, mentioned below, having shown it to be out by only a few percent up to a hydrogen concentration of about 3000 ppm. Of course, hydrogen in the two-phase region alone is not conserved in my treatment as pointed out by Markowitz. On the contrary, one of the important features of my proposed mechanism is that in the presence of a temperature gradient a two-phase region cannot exist over the whole specimen. For example, if the specimen is entirely a + 6 initially, then on application of a temperature gradient, a single phase (a) region at the hot surface develops from time t = 0 onwards. As mentioned in my original paper, the interface between the a and a+d regions moves toward the colder surface of the specimen with a discontinuity in hydrogen concen- tration developing at the interface and increasing with time. This interface moves at such a rate that hydrogen in the specimen as a whole is conserved. It must be pointed out that my distribution equation (Eq. [5] in Markowitz's paper) holds only for linear geometry. It is easy to show that for the cylindrical geometry of Markowitz the assumptions used in my treatment lead to

Jan 1, 1962

By N. J. Gran, W. R. Opie

HYDROGEN in molten aluminum and aluminum alloys, which precipitates during cooling and solidification, is the principal cause of pin hole porosity in ingots and castings. Much attention has been given to determining the effect of temperature and pressure on the solubility of hydrogen in pure aluminum, but little data are available on hydrogen solubility in aluminum alloys. This investigation was undertaken to check results reported for pure aluminum and to show the effect of silicon and copper additions on the amount of hydrogen contained by molten alloys. Previous determinations of the solubility of hy-drogen in molten pure aluminum are plotted in fig. 1. The most reliable data appear to be those of Ransley and Neufeldl and of Baukloh and Oester-len.' The latter authors also report some results on the effect of copper and silicon additions. Up to 6 pct these elements decrease the solubility of hydrogen quite rapidly, with a definite minimum noted at 6 wt pct for both copper and for silicon, although no reason is apparent for these minima. Experimental Procedure The solubility of dry hydrogen in pure aluminum, aluminum-silicon, and aluminum-copper alloys was determined by the method of Sieverts.8 This consists of determining the volume of the gas system above the molten metal at a given temperature and pressure by using an insoluble gas. This volume is referred to as the "hot volume." The system is then evacuated and the soluble gas is introduced at the same temperature and until the same pressure is reached. It is necessary to introduce enough of the soluble gas to fill the space above the metal plus the soluble amount. The difference in the volume of soluble gas and the "hot volume" is the solubility. The accuracy of solubility measurements by the Sieverts' method is primarily depend-

Jan 1, 1951

By F. A. J. Fitzgerald

In any kind of furnace the question of preventing the loss of heat is important, for no matter how the heat is obtained it costs something; and consequently, other things equal, that furnace is most desirable which uses the greatest percentage of the total heat generated for the particular object in view. In the furnace which uses electricity for the generation of heat the importance of preventing losses of heat is very much greater than in any other. To generate 1,000 kg-cal. requires an expenditure of 1.16 kw-hr., and consequently the cost per calorie is always expensive when electricity is used for heating. In heating any material in a furnace a general rule is that the generation of heat should be as rapid as possible. In any given furnace the heat-losses may be expressed as so many watts, and, therefore, the longer it takes to heat the furnace-charge the greater the losses will be. Suppose that a furnace contains a charge to be heated to 1,500°C. and that the average loss of heat is at the rate of 100 kw., then if the process of heating the charge takes 1 hr. the losses will amount to 100 kw-hr.; but if by using a more rapid generation of energy the charge can be heated in 30 min. the losses will amount to 50 kv-hr. An example from experiments on a certain process may be given to illustrate this point. The problem was simply to heat a furnace-charge to a certain temperature, and experiments were made to determine the effect of increasing the rate of generation of energy and comparing the kilowatt-hours required to heat a given charge. Here are typical results : Rate of Generation Energy Per Kg. of Energy. of product 88 kw. 1.7 kw-hr. 93 kw. 1.6 kw-hr.

Jan 1, 1913

By W. N. Logan, P. Simpson

There was less activity in the petroleum industry in Indiana in 1933 than in previous years, owing largely to adverse market conditions. The only development of any consequence was for oil in Perry and Vander-burgh counties in southwestern Indiana, a few gas wells being brought in in Jay County in northeastern Indiana. Indications are that there will be more activity in southwestern Indiana in 1934. Little change may be expected in northeastern Indiana. One hundred and sixty wells were drilled in Indiana in 1933, of which 57 were dry, 44 produced oil, 38 produced gas and 21 either were not completed or information on them was lacking. There were 153 wells abandoned and plugged in 1933, as compared to 205 in 1932. Southwestern Indiana This area centers about Gibson County and is the principal source of oil and gas production in the state. Production is from the Lower Pennsylvanian and Upper Mississippian formations. Oil production for 1932 was approximately 847,000 bbl. and for 1933 was 804,000 bbl. Gas production for 1933 was 942,000,000 cubic feet. The Siosi field, in southwestern Vigo County and northwestern Sullivan County, discovered six years ago, produced approximately 244,000 bbl. in 1932 and 223,000 bbl. in 1933. Production is from Devonian and Silurian formations. The oil is high gravity, but contains considerable sulfur. The Shelburn and other small pools in central Sullivan County produced approximately 68,000 bbl. in 1932 and 2,000 bbl. less in 1933. Production is from one or more of five horizons in the Pottsville and is obtained at 600 to 800 ft. This area also produces approximately 19,000,000 cu. ft. of gas a year, supplying the city of Sullivan. The field is over 20 years old. The Gibson-Pike County area, made up of many small pools, including several in southern Knox and southwestern Daviess counties, produced approximately 486,000 bbl. in 1932 and 450,000 bbl. in 1933. This production is from the Mansfield sandstone of Pennsylvanian and/or

Jan 1, 1934

By A. B. Kinzel

SINCE the exposition of the behavior of certain iron alloys by Sykes1 involving the existence of an austenite loop and the discovery of such a loop in the chrome iron system by Bain,2 there has been much conjecture both on his part and on the part of metallurgists in general as to the exact shape and location of this loop. In previous work commercial steel has been used and the microscope has been employed to locate the critical points so that the position of the loop has been quite approximate. Numerous attempts have been made to measure the critical points of the carbon-free alloys but all of these for one reason or another have failed. A satisfactory method for studying these phenomena is presented here. MATERIAL The first difficulty in this study was to obtain pure chromium-iron alloys. This has been overcome by melting in a vacuum electrolytic Eton and chromium analyzing 99.84 Cr, Fe and C. A pure magnesite crucible was used and the melt allowed to solidify in the crucible. A typical analysis is chromium, 10.10 per cent., carbon, 0.006 per cent., silicon and manganese nil. To overcome the problem presented by segregation, ingots were made into wire 0.04 in, in diameter. This was accomplished by hand-forging the ingots into rods, using an oxyhydrogen flame for heating, in order to avoid carbon. Subsequently the rods were swaged to wire, the heating being carried out in hydrogen. Thus local segregation was eliminated although differences in analysis between portions 50 ft. apart were noted. An electric-resistance method was first tried to determine the critical points, but due to the physical defects in the wire this failed. Bain had previously shown the presence or absence of critical points in a qualitative way by observing the sag in a catenary. The author has devised the following method which gives an accurate determination of the critical points from expansion-temperature curves of suspended wire, a special telescopic dilatometer being used for the purpose.

Jan 1, 1928

By John Primrose

Tube stills having demonstrated their usefulness for refining operations, the later developments in their design have been in the direction of improved thermal efficiency. The earlier designs operated with low furnace temperatures and large volumes of furnace gas because the fuel was burned with much excess air. It was quite possible to provide sufficient heating surface to lower the temperature of the flue gas to within 150" of the temperature of the inlet oil, or when inlet-oil tempera-tures were high to have the flue gas escape at 300" or 350" F. by using the heat remaining in the flue gas from the still to preheat the air supplied for combustion. But even so, the thermal efficiency was low because of the large quantity of air used for combustion. The large quantity of excess air was required to burn the fuel in the furnace at a temperature low enough to prevent overheating the furnace walls and overheating of the oil. Supplying heat to the tubes of the heating surface at a rate beyond the capabilities of the oil to absorb, except with a considerable difference between the temperature of the inside of the tube and oil passing through, would result in overheating the tubes and the oil in contact with them. For these reasons it was very necessary in the older types of tube stills to burn the fuel with large quantities of excess air, resulting in low thermal efficiency despite the low flue-gas temperature. Neglecting loss by radiation, the thermal efficiency could be improved only by burning the fuel with less excess air, but it was necessary to accomplish this without upsetting the furnace temperature conditions existing when large quantities of excess air were used. There are several methods of bringing this about, such as controlling the furnace temperature by returning a proportion of the flue gas to the furnace, or by exposing direct to the fire a heat-absorbing surface so located and proportioned that sufficient heat will be absorbed by radiation to prevent excessive furnace temperatures.

Jan 1, 1928

By F. J. Longworth

FoR a number of years an intensive study has been made to improve the blast-furnace practice at Copperhill not only as to cost% but to provide a good grade of gas for the acid plants. This study took us back to the fundamentals of successful pyrite smelting; namely, a blast furnace working on a clean sulfide ore, free from fines, and the use of quartz high in silica as a flux. In 1919, the quality of the flux was improved and its effect on the metallurgy was very marked. To improve the practice further, it was necessary to work out some method of treatment for the sulfide fines and the siliceous and refractory ores, other than in the blast furnace. A series of milling tests indicated that these products could be successfully treated by differential flotation, and in 1922 plans were made and a flotation plant built. It was estimated that the flotation plant would deliver to the smelter 40 to 50 tons of concentrates per day; the problem was what to do with these concentrates. It was out of the question to attempt to smelt them in a blast furnace because of the dust losses and because our practice demands a charge free from fines for satisfactory operation. There is no custom smelter in the vicinity to which concentrates may be sold, pending the time when the tonnage will be sufficient to warrant roasters and a reverbatory furnace. Sintering and nodulizing were investigated but neither method fitted into our scheme of metallurgy. A close study of the converter practice was then made to see if some method could not be evolved to smelt this tonnage of concentrates in a converter without preliminary treatment. At that time, the converter installation consisted of two 12-ft. Great Falls converters, which were handling 12 to 14 per cent. matte. The heat balance of the converters working with 12 to 14 per cent. matte was more than sufficient to smelt the contemplated tonnage of concentrates but the mechanical difficulties of feeding fines into the Great Falls converter made the use of this type of converter impractical. While there was no opportunity to experiment with the Pierce-Smith converter, equipped with a Garr gun, theoretically it seemed practical

Jan 1, 1925

By T. Sterry Hunt

At the meeting of the Institute in Easton, October, 1873,I made a communication on the Ore Knob copper mine, in Ashe County, North Carolina (Transactions, vol. ii, p. 123), in which I called attention to the chemical decomposition alike of the pyritous lode and the inclosing gneiss rock to a depth of 60 feet, by which the feldspar of the latter had been converted into clay, and the whole rock very much softened. Such a decomposition is well known to be almost universal in the crystalline rocks of the Appalachians south of the Potomac; and if it is only seen in rare and exceptional cases farther to the northward, this, as I have elsewhere pointed out, is due to the fact that the decomposition began and ended in the ages anterior to the drift period, and that the decayed portions which still remained were at that time removed from the surface, except in some localities which were protected from the emding agency. I have lately had an opportunity of studying a remarkable instance of this kind in an examination made last month for the corporators of the Hoosac Tunnel.* The locality is at the western base of Hoosac Mountain, the western slope of which rises rapidly 1300 feet above the town of North Adams, in Berkshire County, Massachusetts, itself 700 feet above the sea level. Through this mountain, as is well known, a tunnel for the Troy and Boston Railroad has lately been opened, a distance of 25,081 feet from east to west. The rock of the mountain consists of mica schist and micaceous gneiss, including in its western half a great mass of harder feldspathic and quartzose strata in part a granitoid gneiss, the strata for the most part dipping to the eastward with variable angles, but with occasional western dips, apparently due to inversion. The crystalline strata of the mountain crest and sides are in many places exposed, and present rounded surfaces, often deeply grooved and striated, but with no appearance of decay. At the western base of the mountain, however, the gneissic rock is in a state of complete decomposition, which was well displayed in opening the tunnel, which, for a distance of several hundred feet, was driven through highly inclined strata so much decomposed that they were excavated with pick and shovel, and without the aid of blast-

By S. E. Bretherton

(San Francisco Meeting, September, 1915) DURING the year 1878-79, Anton Eilers, who was then interested in the lead smelting and refining business near Salt Lake City, Utah, made a somewhat radical departure from the regular practice at that time, which was to use but little lime in the slag, with a high percentage of iron. Lime was not only a cheaper flux than iron, but it enabled the metallurgist to make a more siliceous slag, an economical advantage in smelting where the smelting companies had to purchase either iron or lime to neutralize the excess silica, and penalize the ore shippers accordingly. The larger amount of both lime and silica in the slag also made it of lighter specific gravity, and a better separation of the metals and mattes was secured. This change in the formation of slags for lead smelting was brought about by Anton Eilers, prior to the Leadville mining excitement of 1879. We must also give Mr. Eilers credit for the general introduction of the hollow water-cooled cast-iron jacket for the blast furnace. Again referring to the use of more lime and less iron in the formation of slags,. there is no doubt but that it prevents the formation of a great many so-called "sows" in the lead crucible, such as were made in the early history of lead smelting in the Rocky Mountains; these sows consisted of lead, iron, arsenic, sulphur, copper, and other metals, including gold and silver, mixed with unconsumed fuel, and often, after vain attempts to cut them up or melt them to a suitable size for handling, were buried in the slag clumps to get them out of-sight. Another advantage derived from the adoption of high-lime slags. when smelting ore containing arsenic is the production of less speiss (a by-product heavier than matte, resulting from careless operation of the furnace, the lead being driven out of the crucible and sows built up). This speiss, while usually not as rich in precious metals as matte made at the same time, is too valuable to be thrown away; but it is difficult to treat, and it was thrown away or piled on the slag clumps in the pioneer clays of lead smelting in this country.

Jan 8, 1915

By Richard Schellinger, Ronald H. Carlson, Robert D. Norris

INTRODUCTION A very important key to the success of an in-situ leach venture is proper choice of well field chemistry, in which type and concentration of oxidant plays a significant role. For proper design of well field and plant, an engineer must be able to estimate uranium production levels and their change with time. The rate controlling step in the uranium leach process is generally acknowledged to be the oxidation step (Goddard and Brosnahan, 1980; McKnight and Anthony, 1979; Mays, 1979). Uranium head grade is very dependent upon concentration of oxidant injected into the ore zone. If oxidant levels are too low, uranium production requirements will not be met; if levels ate too high, excess oxidant will be wasted in side reactions with gangue material and leach economics will suffer. To date, no reliable laboratory technique exists for generating data easily translatable to field conditions. Empirical correlations based upon lengthy field testing have been the major tools avail- able to the design engineer to date. During the past five years, FMC has developed lab- oratory techniques for studying uranium leach chemistry under conditions simulating as closely as possible the field situation. Both agitated batch and consolidated core leach procedures have been developed. Results of FMC agitated batch studies are described in detail in a companion paper (Carlson, et. al., 1980). This paper will focus on the technique developed for leaching consolidated undisturbed core under simulated down-hole conditions. Through use of a follow-up computer model (Winkley, 1980), generated data can be translated to expected field response, thus providing the design engineer with valuable information in a relatively short period of time. CHEMISTRY In addition to uranium (+4), other oxidant-consuming species present in uranium ore are iron sulfides and carbonaceous material. Iron sulfides are usually present in concentrations far exceeding those of the other two materials and, therefore, represent the major oxidant-consuming species present in uranium sandstone ore. Previous studies (Carlson, et. al., 1980) have shown that iron sulfides exist in both Texas and Wyoming ores as a mixture of pyrite and marcasite (FeSz); furthermore, uranium mineralization (existing as uraninite) was shown to exist as a fine granular material coating or imbedded in iron sulfide crystals and sand grains (i.e. quartz and feldspars). The leach chemistry of a uranium ore body can be described by the following equations using hydrogen peroxide (Hz021 as oxidant:

Jan 1, 1980

By R. W. Brown, J. L. Loper

The process of sand erosion has been harnessed to perform a useful function—the directed perforating of oilfield tubular goods and formation rock. In this process the sand is carried by a liquid medium and the resrrlting slurry is forced through a nozzle at an extren~ely high velocity. Upon impingement against casing or formation, the fast-moving sand particles erode a perforalion in the casing followed by cavity formation in the medium behind the casing. The many factors influencing the rate and extent of this penetration are inherently difficult to establish experimentally. Equations describing submerged jet behavior have been applied to these conditions. The following paper develops the equations for predicting the performance of the perforating jet. INTRODUCTION The cutting power of high-velocity sand has been well known in the petroleum industry for many years. Sand carried by a high-velocity gas stream causes severe erosion. This effect has been the cause of numerous production problems in certain areas. It was logical to expect that this phenomenon would one day be adapted to useful industrial applications. Development of mobile, high-pressure, high-horsepower pumping equipment in the last decade has made this possible. The sand erosion process involves pumping a fluid containing abrasive solids through a set of nozzles at a high differential pressure (2,000 to 4,000 psi). The pressure conversion into kinetic energy imparts high velocity to the sand particles which, upon impact with the formation face or casing wall, erode the material in an organized pattern. This paper attempts to establish the effects of the various parameters and to predict the performance and limitations of the process. The following factors will be considered: nozzle differential pressure, perforation size, sand concentration, nozzle stand-off distance and backpressure. In general, this discussion is presented along theoretical lines and is substantiated by field results and data where reliable field data exists. POWER EQUATIONS The penetration rate of a high-velocity hydraulic jet is proportional to the power or energy of the jet at the point in quesion. The power of the submerged jet will decrease with distance (or penetration) into the cavity created by the jet. As the cavity is extended into the formation, the power of the jet diminishes to a value equal to the threshold cutting power of the particular formation which is defiined as the lowest power level at which the formation will be abraded by the jet. Obviously, when this point is reached, no further cutting of the formation can occur. It is assumed that this power level for a particular formation is a function of the hardness of that formation. The following equation can be written for the hydraulic process of formation abrasion.

By Fred H. Poettmann, A. L. Benham

correlation of waters and identification of mixtures of two and three waters is important in secondary recovery evaluation studies and studies involving underground movement of waters. The importance of such studies suggests the need for a method to correlate a great number of water analyses to accurately identify and improve the understanding of mixtures of waters. Geochemical analyses of waters furnish a quantitative measure of each of the ions present in a water. Table L shows a portion of the data on many oilfield water analysis report forms in use today. Under "parts per million" are listed the quantitative amounts of each ion in milligrams per liter. Following the work of Stabler' and Palmer", some laboratories have reported additional data to indicate the reaction capacity, or reacting value of each ion. Table I lists data under two subheads for the "reacting value". Under the first subhead, the reacting value is reported in gram equivalents per million, hereinafter called equivalents per million. This value is determined by multiplying milligrams per liter of the ion by a factor equal to the reciprocal of the equivalent weight of the ion. Under the second subhead (per cent) is listed the percentage of each ion based on the total equivalents per million. Sodium is not usually an analyzed value in routine analyses, but is determined by the difference between total negative equivalent per million values and the sum of all of positive ion values for which analyses were made. This difference is reported as sodium, hereafter labelled "sodium". On this basis, the subtotals of the equivalent per million and per cent reacting values of the positive and negative ions are equal. CORRELATION OF WATER ANALYSES DATA Previously reported methods for correlating oilfield waters have used part of the data in Table 1, and can be classified into two categories. Correlation by Chemical Character Correlation methods using the chemical character of waters, as represented by the per cent reacting values of the ionic constituents, have been used by Palmer2 and Tickell. These methods have the limitation of neglecting the ionic concentration of the waters. This limitation can be serious in areas where waters have the same chemical character, but differ in concentration. Correlation by Concentration of the Ionic Constituents The Reistle' and the Stiff methods use the ionic concentration in parts per million and equivalents per million. These methods are effective in differentiating waters of similar chemical character and varying concentration, as in the highly saline waters of the Mid-Continent area. These methods have the disadvantage that they correlate waters by comparing many graphs of individual water analyses to determine the similarity to, or the variance from "type" waters. PROPOSED METHOD OF CORRELATING WATER ANALYSES DATA Correlation graphs presented in Fig. 1 represent water analyses data as points to facilitate the correlation of waters. The graph on the left of Fig. 1 is a plot of per cent reacting value of magnesium vs calcium. The right

?AARONSON, ALFRED E, .Vice-Pres, Mid-Co Petroleum Co , Mid-Co Bldg, Tulsa, Okla '18 ABADIE, EMILE R, Min Engr - Box 927, Porterville, Cal '76 ||ABADILLA, QuiRiCo A, Student, Colorado School of Mines, Golden, Colo. '20 ABBOTT, CLARENCE E, Gen'l Supt, Iron Mines Div, Tenn Coal, Iron & R R Co , 1405 Minnesota Ave, Bessemer, Ala. '04 ABBOTT, Louis BENJAMIN, Chief Engr, Consolidation Coal Co-, Elkhorn Div, Jenkins, Ky '15 ABBOTT, ROBERT R Met. Engr, Peerless Motor Car Co, Cleveland, Ohio. '12 ABE, ASAKA Fujita Min Co, Dojima, Osaka, Japan '14 ABEEL, GEORGE H, JR, Cons Min Engr, 633 St Paul Ave, Los Angeles, Cal '18 ABEL, ALBERT E, Mgr., Pittsburgh Dist, Valley Mould & Iron Corpn, 28th St & R R Ave, Pittsburgh, Pa '19 ABEL, W D, Min. Engr. 3897 Sacramento St , San Francisco, Cal. '19 ABELL, 0 J, Pres & Treas, Abell-Howe Co, 332 South Michigan Ave, Chicago, Ill '19 ABERNATHY, G E Willow Springs, Mo '20 ABEY, HIROSHI, Min & Met Engr, Arakawa Mine, Mitsubishi Co, Senpoku-gun, Akitaken, Japan '17

Jan 1, 1923