Search Documents

By W. T. Isbell

In the Parkes process of lead refining, after desilverization has been completed by means of the addition of zinc, there remains in the lead from 0.5 to 0.6 pct zinc. At this stage in the refining operations virtually all impurities are reduced to refined lead specifications except zinc and antimony. All excess copper, nickel and cobalt have been removed by the zinc additions. The silver remaining should not exceed 0.1 oz per ton. It then remains only to remove the zinc and antimony in order to produce refined lead. At the Herculaneum plant of the St. Joseph Lead Co., practice formerly was to complete the refining by means of oxidation in a reverberatory furnace. This process consisted of heating the lead to 1400O to 1500OF and allowing it to come in contact with excess air passing over the surface of the lead and periodically agitating the bath of lead with air. This procedure not only resulted in the loss of zinc but of a considerable quantity of lead converted to the oxide in the form of dross and fume. The fume, collected in the baghouse, together with the dross was returned to the blast furnace, thus adding appreciably to the circulating load on the blast furnace and refinery. In addition, operation and maintenance of the reverberatory furnace were expensive and required the performance of disagreeably hot and somewhat hazardous work. The process of dezincing with high vacuum was developed at this plant as a substitute for the oxidation process and finally led to lower operating costs, the practical elimination of dross and fume and the direct production of metallic zinc, which is very suitable for re-use in the desilverization process. Essentially this process consists of subjecting the lead to high vacuum, in a kettle provided with means for heating, a bell-shaped member open at the lower end so constructed that it can be immersed in the molten lead, and means for evacuating the interior of the bell and for sealing an agitator. Metallic zinc is thus produced and collects on the upper cooled part of the bell member. This metallic zinc is periodically removed and re-used in the desilverization process. The process is quite simple. It is conducted at a low temperature, thus permitting the use of iron equipment, and shows a material saving in refining costs over the old method. Equipment and Its Uses Degincing Machine.—The equipment employed in this process consists of a dezincing machine, a steel kettle of 120 tons capacity, a vacuum system and equipment for handling the dezincing machine (Fig 1). The dezincing machine consists of a compact assembly, suitable for handling with an overhead crane, consisting of a treating chamber and the agitating mechanism. Treating Chamber.—The treating chamber is a bell-shaped shell (4), similar in shape to a hemispherical kettle with a lid

Jan 1, 1949

By J. H. Frye, J. L. Scott, J. W. Woods

THERE are at least two effects of temperature on the stress required to produce plastic flow. 1) Metals plastically strained for the same amount at different temperatures possess different stress-strain curves and different internal structures (e.g., nature and density of imperfections). 2) There is both experimental and theoretical evidence that the stress necessary to produce plastic flow may vary with temperature even though the internal structure remains constant.1-5 Much of the data in the literature is difficult to interpret because these two effects are simultaneously present. In the work reported here, they are considered separately. Standard 0.505 in. tensile specimens were prepared from high-purity Mond nickel and OFHC copper. Nickel specimens were annealed in hydrogen at 1150°C for 30 min and furnace cooled. This produced an average grain diameter of 1.4 mm. Copper specimens were annealed in vacuum at 525°C for 6 hr and furnace cooled. This produced an average grain diameter of 0.11 mm. Nickel tensile specimens were prestrained in tension at 500°K, whereas copper tensile specimens were prestrained in tension at room temperature. All specimens were cooled to 74°K and heated to room temperature. After these treatments all of the tensile specimens of a given set possessed identical structures. All specimens were returned to the tensile machine and tested at various temperatures and constant cross-head speed. Many of the tensile curves showed well defined yields but, in order to minimize personal judgment, the yield was always chosen as the stress corresponding to 0.2 pct plastic deformation. Results are summarized in the graph of yield vs temperature of test, Fig. 1. All of the specimens corresponding to any one line have had identical treatments and, therefore, have identical internal structures. Thus, each line gives the relation between yield stress and temperature for one constant internal structure. The lowest line, which is for annealed nickel, shows no measurable variation of yield with temperature. This is similar to Blewitt's6 results on copper single crystals, but a variation in yield with temperature was found by Andrade and Henderson' in single crystals of nickel, and by Car-recker and Hibbard8 in annealed polycrystalline copper. The three other lines, which are for prestrained materials, show that there is a linear relation between yield stress and temperature when the internal structure remains constant. Such a relation might be expected from a rate equation such as that of Kauzmannl on the assump- tion that the activation energy is either independent of or linear with temperature. These results would also be expected if the shear moduli of copper and nickel are linear functions of temperature for, as Cottrell and Stokes have pointed out," in all dislocation theories of strength the flow stress appears proportional to the shear modulus of the material. In copper and nickel, since the modulus of elasticity decreases roughly linearly with increase in temperature," it is probable that the modulus of shear also decreases approximately linearly with increasing temperature. A detailed discussion of the effect of these and other factors on the temperature dependence of flow stress in face-centered-cubic metals has recently been given by Seeger.4

Jan 1, 1958

By Charles H. Mitchell

British Columbia is enjoying a period of sustained high-level activity in all aspects and sectors of its mining industry. The total value of mineral production for 1962 was in excess of $229 million. This was the greatest total value attained for any year to date, exceeding the previous record year of 1956 by more than $40 million. It appears reasonable to expect that value of production for 1963, stimulated by increased production attained during the year, and by improved metal prices for some of the major products, will be substantially in excess of that recorded for 1962. Elsewhere in this issue appears a detailed report of prospecting and exploration activity in the Province. For the purposes of this review it is sufficient to state that the level of prospecting and exploration activity during the past several years has been greater than at any previous time and that there does not appear to be any slackening in activity or interest.

Jan 12, 1963

By James L. Poole

INTRODUCTION Companies in the mining industry are subjected at times to currency exchange rate risks and interest rate risks. The former occurs any time a firm deals in more than one currency. The latter occurs anytime a firm is financing itself with borrowings that have a floating interest rate (although a fixed rate can be a problem at times). FOREIGN EXCHANGE RISKS There are two general reasons why exchange rate risks (FX risk) can occur: First, a firm may be building a mine or plant in another country where financing for the plan is denominated in funds other than the country hosting the plant. For example, if a Canadian firm is building a smelter in another country which is being financed with Canadian dollars, the C$100 million for labor, which must be paid in the local currency, has subjected the firm to a C$100 million FX exposure risk. If after the cost estimates were made the local currency appreciates 30% against the Canadian dollar, the cost of labor has increased to C$130 million. (Of course, the local currency could also devalue during this period making the labor cost component less than estimated.) The other reason exchange rate risk arises is due to the fact that the costs of production in one country producing minerals may be incurred in one currency while the production is sold in another currency, such as coal being exported from Canada to Japan under contracts denominated in Yen. In this example, the Canadian firm is exporting coal to Japan and being paid in yen in 30 days at a contract price of 100 Y per ton. Furthermore, assume that the mining firm anticipates a depreciation of the yen against the Canadian dollar of 5% in the next 30 days. Therefore, the mining firm stands to lose 5% of the value of its shipment in a month's time not including carrying costs. In both cases, the mining company risks an adverse change in the exchange rate, that is, the currency the company holds may decrease in value relative to the other currency. There are a number of ways to mitigate the exposure to foreign exchange which can be utilized by the mining company. Optimally, a company should try to match all their inflows and all their outflows in the same currency. For example, if a Canadian firm has mining costs and debt service costs both denominated in Canadian dollars then 100% of their receipts would need to be in Canadian dollars. If a Canadian firm has 70% of its cash outflows in Canadian dollars and 30% of its cash outflow in American dollars in the form of a loan amortization then their receipts would need to be 70% in Canadian dollars and 30% in U.S. dollars. This general principle of matching cash receipts and cash costs in the same currency works fine in a perfect world but what of the real world when these cannot be matched? In actual practice, however, the financial markets have developed a number of ways in which foreign exchange risks can he managed or reduced. FORWARD MARKETS One method is to use the forward markets which are made on a world-wide basis by the commerical banks for foreign exchange. If a firm wanted to lock in the current exchange rate for the receipt of a foreign currency at some point in the future, they could do so by contracting on the forward market with a bank selling that foreign currency at the current rate at the future date. For example, assume that a Canadian firm is exporting coal to Japan which would pay yen in 90 days. If a firm wanted to lock in today's exchange rate they could contract with a bank to sell on the forward market yen in 90 days. When the yen was received the contract would be executed by selling the yen to the bank and receiving the previously agreed upon number of Canadian dollars. Generally speaking, the forward market can be used to sell forward about 12 months. The costs of selling (or buying) forward

Jan 1, 1985

By W. L. Watts

The existence of petroleum in California has been known for many years. From time immemorial the California Indians used this mineral, in the form of asphaltum, for various purposes. In the early history of the State the Catholic fathers utilized it for roofing their missions and other buildings. It is said that in 1855 or 1856 Andreas Pico distilled petroleum on a small scale for the San Fernando Mission. He obtained his crude oil from Pico canon, near Newhall, in Los Angeles county; and he was probably the first refiner of petroleum in this State. In 1856 a company commenced work at the La Brea ranch, in Los Angeles county, and tried to refine the crude oil. In 1857 an attempt was made to produce illuminating-oil from crude petroleum at Carpenteria, in Santa Barbara county; and there are records of similar attempts in other localities previous to 1860; but none of them were successful. The first scientific report on petroleum in California was made by Prof. B. Silliman, who published his researches in 1865. He spoke favorably of the possibility of obtaining petroleum in remunerative quantities in this State, and gave the results of his experiments in the fractional distillation of California petroleum. The next decade was marked by a considerable oil-excitement in California; and a great many companies mere formed for the purpose of petroleum-mining and for distilling crude oil. In most instances these companies did not meet with success; but it must be remembered that the pioneer oil-miners did not

Jan 1, 1900

By C. Gatlin, N. E. Garner

Results of impulsive wedge penetration tests on two synthetic, plastically deforming rocks are presented. Basic data obtained were force-time, displacement-time, and force-displacement curves for the impacts, plus the crater geometry. Wedge geometry and blow frequency were varied over a considerable range. The synthetic rocks consisted of wax-sand mixtures; two waxes of diflerent ductilities were used to provide variable "rock" characteristics. Conventional triaxial tests showed that these synthetic rocks exhibited force-deformation curves and Mohr envelopes quite similar to real rocks, except that strengths were much lower. Measured forces from static penetration tests agreed closely with theoretical values; however, dynamic force values were much higher than the static. These latter disparities are attributed to the viscous nature of the waxes. Thus the utility of these or similar rock models must depend on the scaling of rock viscosity, which is as yet unknown for impulsive loadings at elevated stress states. It appears, however, that some macroscopic, static phenomena may be studied with wax-sand rock models. INTRODUCTION The resistance of solid materials to indentation or perforation by projectiles or other penetrators has been studied by workers in many areas. Despite these efforts no universally accepted laws or formulas are available for describing experimental observations. In the metals field the force-deformation behavior of impacting bodies is often analyzed by the Hertz law for elastic collisions, the Meyer law if plastic deformations occur, or some combination of both.' The similarities of these expressions to empirical drilling formulas of the oil industry are apparent. Beginning with the basic contributions of Simon and co-workers at Battelle,' a number of experimental papers concerning the reaction of rocks to vertical impact have appeared in the U. S. mining and petroleum literature.'-' Most published data have, to date, been obtained at atmospheric pressure, although some early high pressure information was reported by Payne and Chippendale.8 Maurer" has recently utilized available brittle impact data to develop a drilling rate equation based on the experimentally observed proportionality between crater volume and blow energy. His result agreed with earlier efforts by both Somerton, who used dimensional analysis, and Outmans, who used plasticity theory. It has long been known that rocks exhibit different modes of failure depending on the state of stress. The literature in this area is considerable; however, papers by Bredthauer, Handin and Hager,13 nd Robinson", are adequate to illustrate the point. Since rocks flow plastically at certain triaxial stress conditions, the mathematical theory of plasticity has been used to analyze the rock drilling problem. Cheatham'" has altered the wedge identation solution of Randtl to rocks, and has developed useful equations for penetrator forces under a variety of conditions. Outmans" has utilized Hill's solution in a similar manner to develop a drilling rate equation. Both Cheatham and Outmans used the linear Mohr-Coulomb rule to relate rock strength and confining pressure. The actual stress at the hole bottom is not easily ascertained, although photoelastic studies by Galle and Wil-hoit," plus the analytical treatment of Cheatham and wilhoiti8 provide some insight. Consequently it is not clear to what extent the highly idealized rheological model of a perfectly plastic solid can be realistically applied to the rock drilling problem. This paper is the first report on a long range experimental study of crater formation in rocks at elevated stress states. The data presented here are from the first phase of the project. Data obtained from impulsive wedge impacts on two synthetic, plastically deforming rocks are presented. MODEL ROCKS Geologists have long been faced with modelling the behavior of the earth and, as a consequence, have studied scaling problems in some detail.' In general, their main problem is handling the wide disparity between laboratory and geologic time. In our studies the time effects (blow velocity or rate of loading, blow duration, etc.) were essentiafly the same for both. model and prototype, as were were geometry and tooth penetration. Thus application of available scaling laws suggests that Similarity is obtained if the stress-strain curves of model and prototype are similar." For this reason Hubbert and Willis''

By W. F. Holbrook

IN a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 pen cent MgO slags over the range 1475° to 1525° C is included The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple Twelve-gram charges of 0 8 per cent sulphur-metal and 5-gram charge-, of slag were subjected to heating for 30 nun at a prescribed temperature The charges were analyzed for sulphur content For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal Six slag and metal charges were made coincidentally in 5/8-in holes in a section of an electrode graphite rod One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO SLAGS WITH MAGNESIUM OXIDE CONSTANT 15 Per cent MgO -The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SI02, 5 to 27 per cent A1203 and 24 to 53 per cent CaO Variation in composition has been in steps of 2 per cent over much of the area Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered m steps of 4I per cent and even

Jan 1, 1938

By George Tryon, E. A. Barnard

The importance of the conservation of the waste heat contained in copper reverberatory furnace gases was realized very early by those in charge of operation at Anaconda. The first attempt to utilize it was in preheating the air used for combustion of the coal. This was done by forcing the air through ducts surrounding the flue-gas downtake and continued down beneath the furnace hearth to the firebox. Any small advantage gained by the heat transferred from the flue gases was more than offset by the losses sustained in cooling the hearth, therefore this process, after several trials, was soon discarded. It was first used at the Old Works as early as 1893 and again for a comparatively short time on the original furnaces at the Washoe smelter, or present works. Water-tube boilers came into general use very rapidly after 1890. Their adaptability for waste-heat steam generation, as well as the saving to be effected by the production of cheap steam from this source, was soon recognized. The first waste-heat boiler to be used in connection with a matte furnace at Anaconda was installed in September, 1900, at the "Old Lower Works." It consisted of a 100-hp. "Cook," vertical water-tube boiler. This boiler had 65 small perpendicular tubes arranged in concentric circles around a 10-in. tube in the center. These tubes were expanded into 4 ft. 4 in. inside diameter cylindrical steel top and bottom drums which served as the steam and mud drums respectively. This boiler was set in a cylindrical brick housing into which the furnace gases entered just above the mud drum and thence circulated upward around the tubes and steam drum to the stack. This installation proved unsatisfactory, presumably on account of difficulty with dust, and was soon abandoned. However, the possibilities for steam generation were undoubtedly encouraging for shortly afterwards (December, 1900) a 300-hp. Stirling boiler was installed, to be followed by two more in the spring of 1901. The choice of the Stirling type of boiler for application to copper reverberatory furnaces was particularly fortunate, as the arrangement of the tubes appears to combine to a great extent the maximum contact of the gases with the heating surfaces of the boiler and at the same time

Jan 1, 1934

"The zinc concentrator of the Butte & Superior Copper company, shown on the opposite page, represents an industry which is coming into importance in Butte. The existence of large bodies of zinc ore in some of the silver veins of Butte has been realized for years, but it is only recently that some of them have proved amenable to successful concentration. Most of the zinc ores thus far found in the camp are mixed with considerable pyrite, but those found in the Black Rock and Elm Orlu mines contain very little pyrite, so that a concentrate low in iron is possible.The Butte & Superior mill is rated at 1,200 tons daily capacity. The ore is sphalerite, most of which is finely disseminated through a hard quartz gangue, with small quantities of galena, pyrite, chalcopyrite, rhodocrosite and rhodonite. In mining, the included granite and the low grade vein matter are sorted out and used for waste filling so that the ore as it goes to the concentrator will carry about 20 per cent of zinc, 1 per cent lead, .25 per cent copper, 8 to 10 ozs. silver and a little gold. The ore bodies ranging from 5 to 103 feet in width, are mined by the square set method and filling of stopes with waste rock.The ore is hard and tough requiring extensive crushing and grinding equipment, consisting of Blake and gyratory crushers, 54-inch and 42-inch high speed rolls, Chili mills, Tube, and Conical mills. All of the lead con¬centrate and part of the zinc concentrate are recovered in the upper part of the mill by jigs and tables. The classifier overflow and the re-ground jig and table tailings go to settling tanks and from there to the Hyde Flotation process, where the balance of the zinc concentrate is recovered, and the tailing go to waste."

Jan 1, 1913

By P. M. Aziz, I. Markson, C. S. Barrett

The abnormal after-effect in twisted wires that occurs when untwisting is interrupted by etching con be brought under control and used to study the mechanical properties of thin surface films and how they are effected by reagents and heat treatment. Results are given of studies of oxide films on high purity aluminum. IF a wire is subjected to plastic deformation by torsion and then released, it untwists in the normal after-effect, but under certain circumstances the untwisting is abruptly lessened or reversed by the application of an etchant to the wire.1,2 This abnormal after-effect may occur, for example, if there is a coherent oxide film on the surface of the wire which is removed by the etchant. Following a suggestion of A. H. Cottrell that predicted this effect, it is attributed to dislocations that had piled up beneath the oxide layer and represents the rapid release of residual stresses caused by these dislocations. When the layer is removed, the stress relief may be by escape of piled-up dislocations from the metal, or by an activation of latent sources of dislocations located at the surface, together with rebalancing of elastic stresses to compensate for the loss of stressed material, as in a residual stress analysis determination, these mechanisms acting singly or in combination.' The slower the attack of the reagent, the more gradual is the stress relief and the smaller the change in strain rate when the reagent is applied. A study has been made of the factors that influence the magnitude of the normal and abnormal after-effects with the object of developing techniques suitable for a quantitative investigation of the influence of various surface films on dislocations in wires, and of the rate and extent of the attack on the films by different reagents. It was found that reasonable sensitivity and reproducibility could be achieved if a suitable choice of variables was made and if these variables were held constant through a series of experiments. The method was then applied to a study of oxide films produced and treated in different ways on the surface of high purity aluminum wires, and to a study of the damage to these films caused by various reagents. Experimental Procedure The material used throughout this work was prepared from 99.9968 pct Al. This high purity aluminum was melted, cast into 1/2 in. diameter ingots, and then swaged and drawn without intermediate annealing to 0.040 in. diameter wire. A sketch of the apparatus employed for twisting is shown in Fig. 1. The test wires were mounted into the apparatus by cementing one end of the wire to the beaker and the other to the tube with laboratory wax of high melting point. The length of the wire between the waxed joints was 4.2 & 0.2 cm. Extreme care was taken during mounting to avoid cold-working the wire. The wire was twisted through 335" in 2 to 4 sec by rotating the pinion on the gear box until the vertical post on the rotating table, which was initially touching the horizontal stop, was arrested by the stop. All the tests were conducted with apparatus and reagents at the same temperature (about 25°C). In all tests, except those where the duration of the initial torque was investigated, the torque was applied for a period of 2 min. At the end of this time the table was rotated back a few degrees away from contact with the stop and the wire allowed to untwist. The after-effects were measured by reflecting a beam of light from the mirror shown on the apparatus. After the wire had untwisted for 6 min, a reagent was carefully poured into the beaker and thereby applied to the surface of the wire.. In some tests the liquid in the beaker was removed after a few minutes and replaced by an-

Jan 1, 1954

By V. Koump, T. F. Perzak, R. G. Olsson

The vate of dissolutioz of carbon in molten Fe-C alloys urns studied by votating- cylindrical g-vaphite sairlples in a stationary crucible containing the melt. The rate of dissolltion was determdined from the change in the bnth co)npositiorz. Alccss-tvansfev coeffi'cients, calcilated with the assurlption that the inte)yacial liquid ulas saturated with carbon, were found to be in agreement with an existing Correlation fov mass transfer jroni votating cylinders. It is corzcllrded tlat, itz the wnge of- Reynolds' numbers itzvestigated (790 to 18,000), the vate of dissolutio of carborz in Fe-C alloys is controlled by tile rate of carbon difirsion from the interface. The dissolution of carbon in molten Fe-C alloys has been the subject of a number of investigations. Most of these investigations have been inconclusive because of poorly defined experimental variables. Two of the more sophisticated studies are summarized below. Dahlke and Knacke' studied the phenomenon by, in part, immersing graphite rods into 0.5 pct carbon-steel for different lengths of time. Since the experiments were conducted in air or in CO atmospheres, the melt was strongly agitated by gas evolution. It was concluded that the change in bath composition as a function of immersion time was in agreement with the assumption that the dissolution process was transport-controlled. The hydrodynamic conditions in these experiments, however, were not well-defined and gave no indication of the nature of the dissolution process at higher fluid velocities. In a recent study Shurygin and ruk investigated the dissolution of carbon in molten Fe-C, Fe-Si, Fe-P, and Fe-Ni alloys. Small graphite disks were rotated in a crucible containing molten alloys under such conditions that only the lower face of the disk was exposed to the melt. The results of this investigation indicate that, over the range of velocities (100 to 1000 rpm) and bulk liquid concentrations (0.7 to 4.5 wt pct C) considered, the dissolution of carbon in the iron alloys is limited by the diffusion of carbon from the interface to the bulk liquid (a transport mechanism). For the particular geometry used by these authors, exact analytical solutions of hydrodynamic and diffusion problems are aailable. Hence the experimental results obtained by Shurygin and Kryuk permit the evaluation of diffusion coefficients of carbon in the four systems investigated. In the present investigation a series of experiments were conducted in which the rate of dissolution of carbon in Fe-C alloys was measured under conditions which permitted wide variation of the fluid velocity and the carbon concentration of the bulk liquid. Graphite cylinders were rotated at different speeds in a stationary concentric crucible containing various molten Fe-C alloys. THEORETICAL DEVELOPMENT In general, the resistance to mass transfer from a solid interface to a turbulent liquid is assumed to reside in a laminar boundary layer adjacent to the interface. If it is also assumed that the diffusion coefficient is independent of concentration, the steady-state rate of dissolution for the case of arbitrary liquid and solid densities can be obtained from the integration of the equations of continuity. The derivation is similar to that used by Lommel and chalmers4 for the case of pl = ps. The solution, expressed in terms where N = rate of diffusion of the solute from the interface. Exact analytical solutions of the hydrodynamic equation for the boundary layer thickness are available for only a limited number of geometries. Consequently, a mass-transfer coefficient, k, is usually

Jan 1, 1967

The petition for the formation of a Tulsa Section was granted. The final budget for the year 1917, and the tentative budget for the year 1918, were adopted. The Secretary was instructed to continue to send the Bulletin to all members whose dues have been remitted on account of their being in the war service, but to hold the Transactions and send them on request to the address furnished for the purpose. The issues of the Bulletin were presented to the Federal Fuel Administration, at its request, with the compliments of the Institute. Fifty-nine Members, five Associates, and fifteen Junior Members were elected. The resignation of one member was accepted. The clues of four members who are on active duty at the front were remitted. An extension of time for the payment of clues was granted to four members, upon request.

Jan 2, 1918

By F. N. Kissell, R. A. Jankowski

The US Bureau of Mines, in close cooperation with the mining industry, has recently established several improved face ventilation techniques for longwall mining systems. These include coursing the primary face intake from tailgate to headgate, installing curtains at the intake end of the longwall face, and identifying improved techniques for measuring face ventilation parameters on longwall sections. Applying these techniques throughout the mining industry should reduce the health hazard associated with excessive exposure to respirable dust.

Jan 1, 1984

By Dennis Z. Mraz

An engineering procedure for designing the minimum separation between solution mined caverns in bedded salt deposit is described. The procedure is based on data obtained by in-situ and laboratory test methods. The formulae utilize the concept that salt rock under high pressure in a deep salt rock deposit would behave as a perfectly plastic substance, and that the active opening surrounding a typical cavern could be described by a circular ellipsoid. The paper describes the calculations required for the safe design of a solution mined salt cavern field.

Jan 1, 1984

By C. R. Sandberg, C. A. Connally, N. Stein

This paper describes the results of volumetric efficiency tests on oil well pumps handling gas oil mixtures. The work was performed in a large scale, above ground unit wherein test conditions could be accurately controlled and measured. The main variables studied were gas/oil ratio (including gas from solution and free gas mixed with oil), pump compression ratio, pump stroke length, pump speed, and clearance volume between the valves at their closest approach. Results are presented for two different pumps and for oils of two viscosities. Relatively small amounts of gas entering the pump resulted in large decreases in volumetric efficiency. Under conditions where the pump was operating at reduced efficiency because of the presence of gas, it was found that variation in the clearance volume between the standing and traveling valves had a considerable effect on pump efficiency level. This effect of the valve clearance volume was found to be significantly altered by the viscosity of the oil used in the tests. The effects on pump efficiency of the other variables studied were found to be relatively small over the range of conditions utilized. INTRODUCTION The production of oil by pumping is often hampered by low volumetric efficiency. A direct increase in lifting costs results from low volumetric efficiency. An indirect increase in lifting costs, probably greater than the direct increase, results from additional wear and tear on pumping equipment and from the down-time necessary for the repairs which can be traced to low-efficiency operation. Both increases in lifting costs tend to reduce economically recoverable oil. A number of different factors can contribute to low pump efficiency. A known basic cause of low efficiency is the presence of free gas in the pumped fluid. Pump volumetric efficiency is calculated only on the basis of liquid pumped and because any free gas pumped is discounted, this volume of free gas would represent a loss of pump efficiency. However, gas also causes a reduction in pump efficiency because it is a highly compressible fluid. It is known that pumps some- times "gas lock" because of excessive gas-to-liquid ratios in the pump barrel. Little is known of the role of gas compressibility in the intermediate case where the pump is operating at low efficiency. The opinion exists, however, that oil-well pumps tend to operate at higher efficiency with long stroke lengths at low speeds, but no quantitative studies of these pumping variables have been reported. It was believed that a much better understanding of the variables which control pump volumetric efficiency could be obtained and that possibly some suggestions as to the methods for increasing efficiency might be found from a study of the operation of pumps handling gas under closely controlled conditions. Previous investigators have studied the effects on pump efficiency of such factors as oil viscosity, oil temperature, slippage of oil. past pump plungers, pump submergence, valve size and spacing, pressure above pump plunger and fluid vapor pressure. However, none of these published investigations were conducted with pumps being subjected to large amounts of gas such as might be the case in a pumping well, nor did any of the investigations study the effect of variation in stroke length or pump speed. A large-scale teat unit was therefore constructed for studying the operation of pumps handling gas and for evaluating effects of such variables as pump stroke length and pump speed. PROCEDURE AND EQUIPMENT A schematic diagram of the pump testing equipment is given in Fig. 1. A 45-ft length of 6-in. casing is mounted vertically in a 65-ft tower. Sight ports are mounted in the casing at intervals near the location of the pump intake and the liquid level in the casing. These sight ports are fitted with Lucite windows sealed by neoprene "0" rings. The Lucite windows are machined to conform to the I.D. of the casing so that no obstruction to flow is present along the casing wall. The casing is fitted with a tubing head and 2-in. tubing is hung inside the casing. Pumps are seated in a shoe attached to the 2-in. tubing. A 1-in. polish rod is attacked directly to the pump without any intervening sucker rods. The top of the polish rod is attached to the weight carrier, which contains a number of weights to be used to force the polish rod in against tubing pressure on the down-stroke. This is necessary because a long string of sucker

Jan 1, 1953

Noranda Mines, of Quebec, signed a contract for construction of a $20 million copper refinery at Gaspe, P.Q. The plant is expected to have a 65500-ton daily capacity for both concentrator and smelter. Extensive drilling. around Gaspe has revealed more than 65 million tons of 1 to 2 pct copper in several deposits. Cerro de Pasco Corp. has called a special stockholders meeting for August 19 to obtain permission to engage in the oil and natural. gas business, in addition to its present production of zinc, lead, copper, silver and other metals. St. Joseph Lead Co. recently entered the oil development field. The United States, Canada and Great Britain have agreed to establish a permanent organization to work on unification of engineering standards. General accord has been reached on drafting standards and practices, screw threads, fittings for gas cylinders, and fits and tolerances. Permanent committees will study these fields. Reconstruction Finance Corn approved the largest sum in its history. for a mining enterprise when it loaned $94 million to San Manuel Copper. Corp., of Pinal County, Ariz. The loan will be used to increase production of copper and molybdenum, in what was described as-the biggest copper deposits in the country. Three large gold mining concerns operating in the Philippines told the Philippine Wage Board that they would be forced to close if they had to boost miners' wages 500 to $2 per day. The companies are Mindanao Mother Lodes, Benguet Consolidated, and Balatoc Mining Co.

Jan 1, 1952

By Malcolm C. Bridges

A review of the application of geomechanics to open stope mining in Australia was recently undertaken for the Australian Mineral Industries Research Association (AMIRA). It compiled the current state of geomechanics and its application to open stope mining, and recommended avenues of research which should be supported by the industry. Information was compiled for eleven mines which use the method. This included their geological setting, the performance of the mining and evolution of the method, properties and behaviour of rock and backfill, and techniques for measurement and analysis. Open stoping accounts for about two-thirds of production from underground mines in Australia. In the future this proportion will progressively increase and the method will become more complex. Overall, the method is being sucessfully applied, but its full potential is not being achieved because a range of problems and limitations are evident within the mines. Many of these are common to several or more mines. These include: zones of poor ground conditions that delay access and stope development; crown pillars that are irrecoverable; substantial overbreak from the walls and backs of stopes; and lack of a widely accepted method to design systems of stopes. Generally, geotechnical information and techniques for applying it to mining are well-developed. However, it nee

Jan 1, 1983

The following resolution was prepared, by the War Minerals Committee and was submitted by it to the Board of Directors of the American Institute of Mining Engineers, asking that it be passed by the Board and used to the best advantage to secure the end desired. WHEREAS, the steel industry of the United States is almost entirely dependent on the importation of foreign manganese ores, the consumption of which for the year 1918, it is estimated, will exceed 850,000 tons; and WHEREAS, the ships now engaged in transportation, especially from Brazil, are needed with ever increasing urgency for supplying our Army and Navy forces abroad; and WHEREAS, much shipping may be spared from manganese transportation and the domestic sources of manganese may be utilized, provided the steel manufacturers of the United States will cooperate to this end by taking advantage of the possibility, in open-hearth and Bessemer practice, of so called "residual" manganese, and by using spiegeleisen instead of ferromanganese, thereby following the example already set by three large and prominent steel producers; BE IT RESOLVED, that the Board of Directors of the American Institute of Mining Engineers urges the steel manufacturers of America, for patriotic reasons, to give immediate consideration to the development and utilization of domestic manganese ores; to use no ferromanganese, except for the manufacture of grades of steel below 0.15 per cent. carbon, to use domestic ores whenever possible in place of the high-grade imported ores; and to urge their associates and colleagues in this and other possible ways, to vie with one another in releasing ships for importation of any materials that cannot be secured or produced in this country.

Jan 1, 1918

By Douglas M. Smith

Silver-gold ratios were studied at the Tayoltita epithermal vein deposit using channel sample, channel sample line, stope, ore body, and vein sample populations. The ratios are highly variable among individual channel samples (25:1 to greater than 500: 1) with both high and low values randomly distributed within ore bodies and veins. Whole vein ratios for the 14 most important ore producing structures range from 44: 1 to 105:1, and show zonal distribution relative to two small granitic stocks, low values closest to the intrusives. The zoned nature of the deposit suggests that the stocks, apophyses of an underlying batholith of late Eocene age, were the heat engines which powered the hydrothermal system responsible for ore deposition.

Jan 1, 1980

By B. J. Klee

What is the economic basis for direct, continuous particle size measurement and control? First, precise grinding control is necessary to achieve and maintain a specified recovery and throughput. Second, throughput and recovery are direct functions of particle size-and these two factors control the economic performance of the ore concentration process. Third, only size-based control using a particle size and percent solids monitor (PSM) has achieved the necessary precise control. Recovery, throughput and cost can be accurately measured for various concentrator operating conditions if particle size is closely controlled. From such data the economic results of different particle size grind points can be analyzed. This will reveal the best combination of recovery and throughput to meet objectives established by financial management. Predictable, repeatable response to set-point selection is essential if the projected profitability of the mill is to be reached.

Jan 11, 1976