Search Documents

By W. A. Hoyer

A pulsed high-energy neturon-induced spectral logging tool has been built and field-tested. The reaction of deuterium on tritium is used to generate pulses of 14-Mev neutrons. By detecting only the prompt gamma rays produced by neutron inelastic reactions in the formation, the presence and relative abundance of carbon, oxygen, calcium, silicon and other important elements may be ascertained from a gamma-ray spectrum. Gamma-ray spectra obtained in a shallow test well and in experimental field use show that it is possible to identify formations and their contained fluids. INTRODUCTION The penetrating gamma rays from naturally occurring radioactive elements in subsurface formations have been used for a number of years in well logging as a means of characterizing and distinguishing strata. Still another nuclear logging method which has been employed for some years consists of the bombardment of strata with neutrons and the measurement of the number of gamma rays produced by neutron capture reactions involving elements in subsurface strata.' Since one of the principal elements entering into capture reactions is hydrogen, the latter procedure essentially results in a hydrogen log, whether the hydrogen be in combined form in either oil or water; thus, the log gives an indirect measure of porosity. These methods, with various refinements, have been developed to such an extent that they have become routine procedures in formation evaluation. Neither gamma-ray logging nor conventional neutron logging, however, yields sufficient information to permit unequivocal identification of the mineralogic composition of formations, and neither method gives information which may be used for the positive identification of hydrocarbons in strata. Accordingly, a number of efforts have been made in recent years to gain additional information from nuclear logs. Brannon and Osoba have shown that it is possible to identify naturally occurring radioactive elements in subsurface formations by spectral analysis of gamma rays emanating from these elements. Such an identification is of value in the characterization of strata. A simplified form of spectral analysis of gamma radiation resulting from neutron capture reactions between elements in earth materials and bombarding neutrons has been used with some suc- cess under favorable conditions to differentiate between petroleum and water. This method relies upon the relatively high energy of gamma radiation from neutron capture by chlorine and, in effect, furnishes a chlorine log. In areas in which interstitial water is of sufficiently high salinity, this log can give valuable information on water saturation and, thus, indirectly on hydrocarbon saturation. Still another approach to obtaining more information by nuclear techniques is "activation logging", in which certain elements yield short-lived radioactive isotopes on neutron activation and, thus, can be detected by gamma-ray spectral analysis. From the standpoint of determining by nuclear logging methods the mineralogic composition of strata and the presence or absence of hydrocarbons, it is essential that information be obtained on the presence and relative amounts of several elements such as carbon, oxygen, hydrogen, calcium, silica and others. Some elements, such as hydrogen, chlorine and sulfur, can be determined by spectral analysis of gamma radiation resulting from neutron capture reactions."" Others — carbon and oxygen, for example — do not enter readily into capture reactions but do yield gamma rays of characteristic energies from inelastic scattering reactions with high-energy neutrons. Accordingly, the latter reactions are of particular interest as a means of identifying hydrocarbons in subsurface strata. Several years ago it was recognized that information requisite to the identification of subsurface strata and of contained fluids could be obtained by pulsed operation of a subsurface neutron generator and associated gamma-ray detector. It was contemplated that pulsed operation would be effective in discriminating in time that gamma radiation which results predominantly from inelastic scattering reactions from that gamma radiation arising from neutron capture reactions. Accordingly, research was continued and construction of such a device was initiated. Although many problems were encountered, they were solved successfully. The following sections describe the tool which has evolved, its performance and the results which have been obtained with it to date. THEORY OF OPERATION OF NEUTRON-INDUCED GAMMA-RAY SPECTRAL LOGGING TOOL THEORY OF INDUCED NUCLEAR REACTIONS Of fundamental importance is the fact that an element, when bombarded with neutrons, emits gamma radiation of energy characteristic of that element. In theory, therefore, an element may be identified by

By G. E. Agar, A. L. Mular

G. E. Agar (Manager, Minerals Processing Research, International Minerals & Chemical Corp., Skokie, III.) — The author notes a discrepancy between the parameters a and ß which are the slopes of the size distribution and energy-size modulus plots respectively. The reason for the discrepancy and the systematic decrease in the magnitude of a with grinding time is abundantly clear from the work of Fuerstenau8 on dry grinding. Fuerstenau shows very clearly in his Fig. 5 that at short retention times the parameter a is the same as that obtained by sizing over the complete size range. From this figure, it is obvious that sizing to only 400 mesh gave distribution curves similar to Mular's - that is, the slope apparently decreased systematically with increased grinding. As a consequence of the improper determination of a, the magnitude of ß given by Mular must be larger than the true value. In order to demonstrate this, the following Fig. 6 was taken from Mular's paper (his Fig. 1). Fuer-stenau's results show that we can approximate the correct value of K by drawing lines parallel to the short retention time curves through the 400-mesh

Jan 1, 1963

Man: A purely detached consideration of nature and the place of man in it may easily result in somewhat pessimistic conclusions as to man and his destiny. However, when we come to the evaluation of man's role in the development of natural resources and his achievements in this field, a more optimistic tone may be justified. Hence the possible contradictions between Man and Nature, Perfection, and the present chapter are more apparent than real. After all, progress must have a foundation of optimism, and we cannot challenge either the faculty or the students to better work and to a progressive and constructive outlook without an underlying tone of optimism and basic faith in the future. Geology is the basic science of Mother Earth; the science of the natural forces that have produced and modified the structure of our globe; the science of minerals and rocks; of landscapes and soils; of water supply and mineral resources, including mineral fuels; and of the history of life, both plant and animal, as revealed by fossils in rocks. It is difficult to reduce man and his historical significance to their proper relationship with regard to the earth and its history. Processes of rock formation have continued for at least two billion years; man's activities have been in evidence only a few thousand years. As a means of comparison, if the height of the Empire State building were to represent geologic time, the thickness of a nickel placed on the tower would just about repre-

Jan 1, 1950

By Frederic Lahee

THE purpose of this paper is to demonstrate the similarity of the oil-producing structures in the Mexia1 fault zone, and to show how the apparently very irregular well logs in these fields may be used for the practical interpretation of subsurface conditions. The Mexia oil field, in Limestone County, Tex. (Fig. 1) is closely associated with a fault that trends about 30° east of north and has a displacement of between 200 and 400 ft., with downthrow on the west. Minor slips accompany this major fault, some being roughly parallel to the main break while others are transverse to it. These faults belong to the so-called Mexia fault zone, a belt of fracturing that has been traced in its characteristic features southward to near Kosse, 15 miles south of Groesbeck, in southern Limestone County, and northward at least as far as the Trinity river at the eastern border of Navarro County, and possibly as far north as Hunt and Hopkins counties.2 The Balcones fault zone, from 30 to 40 miles west of the Mexia fault zone, differs from the latter in that its principal displacement is a down-throw on the east. In this respect, it is exactly the opposite of the Mexia displacement. Between these two zones of major faulting lies a great down-dropped block, or graben, which is broken by numerous minor faults.

Jan 2, 1925

By Edward F. Winter, C. E. Ruoff

A silicon solid-state array image scanner is described. This paper deals with structural and performance properties of the array which basically consists of PIN photo and gating diodes, and low capacitance isolation diodes. Each chip of the array is composed of an 8 by 9 matrix of photo detector cells; each cell contains one each of the three diode types mentioned. This x-y matrix is read a column at a time with an access delay of approximately 100 nsec per column. It is designed to detect the presence or absence of illumination within 10-mil diam image spots located on a 15- by 15-mil grid. Radiant power level of an illuminated spot is low; of interest is the range around I uw with a of 8400g Structural improvements to the original array which will result THE purpose of this paper is to describe the results of a solid state scanner exploratory development activity. The scanner is intended to sense the presence or absence of low-level illumination falling upon a matrix of 10-mil wide squares arranged on a 15- by 15-mil x-y grid pattern. The light of interest has a wavelength of 8400, characteristic of radiation emitted from a GaAs lasing diode. This wavelength matches well the spectral absorption of silicon,' thus the well-developed silicon processing technology can be applied to fabricating large integrated arrays of PIN photocells to sense the radiation. The illumination state of the cells of the array is read, one column at a time, by addressing a drive line of the particular column in question and examining the state of those sense lines which are orthogonal to the drive Lines of in greater sensitivity at various wavelengths, both above and below 8400Å, and in greater speed are presented. These include variations in diffusion depth, resistivity of N and P regions, isolation techniques, and packaging. Trade-offs between access speed, cycle frequency, and sensitivity are discussed. A packaging approach to achieving an array composed of several chips is described. Requirements on this package are: 1) maintenance of 15- by 15-mil pitch of the light sensitive cell position, therefore positional accuracy of mounted 8 by 9 cell photo detector chips; 2) maintenance of inherent high array speed even though signal levels are low through high density close proximity mounting of monolithic sense amplifier circuitry. the array. One bank of N sense amplifiers is required, where N is the number of photodiode cells in each column of the array. CELL AND CHI" STRUCTURE A photograph of a single monolithic cell is shown in Fig. 1. Each cell is composed of three junctions, an isolation junction, a logic or blocking diode junction, and a photodiode junction; all of these junctions are connected electrically by a common N region. An electrical schematic of four cells of the array is shown in Fig. 2 with the associated driver and sense amplifier circuits in block diagram form. Note the common cathode configuration of the three diodes of each cell. Fig. 3, a diagram of the cell vertical struc ture, illustrates how the electrical configuration of

Jan 1, 1970

By C. P. Sandberg

Having been occupied in inspecting and testing iron and steel these twenty years in England, and previous to that having served on the Board of Iron Masters in Sweden, I have naturally been very much interested in the subject of the use of steel for structures. I regret that I can offer but comparatively small experience on that had, having had principally to do with steel for railway plant and rails, but granting these to be a kind of "structure," and also that steel for rails has similar duties to perform in many respects, and is generally manufactured in the same way and at the same works as steel for stuctures, properly speaking, I may be entitled to offer an opinion on the use of steel in construction. In a paper recently presented to the Institution of Civil Engineers in London, Mr. Ewing Matheson has recommended that the Board of Trade rules should be amended so as to allow of a maximum straining of 8 tolls per square inch instead of 6 1/2 tons. But it is equally necessary to fix the amount of ductility or elongation of the metal for such a strain as 8 tons. Strength and ductility should always be spoken of together. Mr. Matheson says that steel can be manipulated in the factory in the same way and with the same tools as are used for iron. This can only be granted for mild steel; for hard steel would be spoilt by the rough mechanical treatment which iron can stand, such as punch ing, for instance; and the remedy for regaining the strength lost by punching hard steel, viz., annealing, cannot always be applied. Noth ing proves this fact better than the punching of steel rails of consid erable hardness, which caused fractures at an early period of steelunaking, and which resulted in the stipulation for drilling instead of punching the bolt-holes, which had been formerly applied to iron rails without any damage. In fact commissions to establish standard tests are now working on the Continent, principally in Germany, where

Jan 1, 1882

By J. A. Dresser

The controlling supply of asbestos for the world is obtained from southern Quebec, 150 miles or less north of the international boundary line between Canada and the United States, and about 75 miles south of the city of Quebec.

Jan 1, 1915

By Ferris E. Sainsbury

As most mining companies utilize contractors rather than in-house drilling departments, it is difficult for most mining engineers to become familiar with drilling techniques This chapter will explain the various drilling options available to the mining industry through the services of a drilling contractor. It will also suggest improvements in program planning and specification writing by the mining company representatives to enable them to derive maximum benefit from the contractor.

Jan 1, 1979

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given below. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers.

Jan 1, 1923

By A. L. Mular

Several capital cost estimation procedures are reviewed briefly, although the factored estimate method is discussed in preference. A table of cost versus equipment parameter data is provided, where the cost may be updated from the current value of the M&S cost index for mining and milling. Cost equations are useful to prepare computer programs which perform capital cost calculations. The use of the factored estimate method is illustrated.

Jan 1, 1978

By J. Amanat, H. J. Siriwardane

A numerical procedure based on nonlinear finite element analysis has been developed for predicting subsidence profile over longwall mine panels. The developed procedure has been verified by comparing predictions with published field observations at several mine panels. This paper presents certain aspects of predicting subsidence profile over mine panels located in hilly terrain. Analysis of four such cases are presented herein.

Jan 1, 1984

By T. F. Archbold, W. H. King

THE diffusivities of gold in polycrystalline copper have been determined in the temperature range from 700° to 1000°C by the utilization of the neutron-activation method. Martin, Johnson, and ~saro' used this method for their investigation of the diffusion of gold into copper at 375° and 550°C for 59 days in order to circumvent the experimental difficulties imposed by the 2.7-day half-life of Au-198. They employed the conventional technique of depositing Au-198 on copper specimens for short-time dif-

Jan 1, 1965

By D. M. Thayer, P. B. Linkson

High intensity wet magnetic separation methods have received much attention in the search for alternative and effective methods to treat weakly magnetic minerals. This paper examines the incorporation of such techniques in the beneficiation of a non-sliming specular Michigan Hematite. The dependence of separation efficiency and beneficiation of specular hematite on various parameters controlling the operation of such a device is investigated experimentally. Particular attention is focused on particle size limitations imposed in these separations. In light of these data, metallurgical balances are presented and an attempt made to rationalize the various models suggested in the literature.

Jan 1, 1982

By Raymond B. Ladoo, C. A. Stokes

This paper summarizes the economic problems of the industrial mineral industries which are essentially different from those of the metals and the fuels. Failure to understand and evaluate such factors as markets, place value, and substitutions of one mineral for another may be disastrous. The engineer should be as responsible for profitable operation as he is for technical efficiency. The Raw Materials Survey of Portland, Oregon, is described.

Jan 2, 1950

By Walter C. Labys, Fereidoon Shahrokh

This paper presents an application of computer simulation methods to the modeling and forecasting of the United States coal market. The computer methods employed as well as the model constructed are based on economic and econometric theory. The contents of the paper include a description of the coal market, the corresponding computer model, tests of model validation, computer generated scenarios for the period 1980-1985, and comparisons of the scenarios generated with that of other major coal forecasts.

Jan 1, 1983

By James Gayley

The paper presented to the Institute in 1910, by H. O. Hof-man, on Recent Progress in Blast Roasting,' has called the attention of the iron industry to the adaptability of these processes to the reclamation of by-products such as flue-dust and blue billy, and the better preparation of concentrates and fine ores for use in blast-furnaces. The waste of valuable iron-ore through the production of flue-dust has increased at an enormous rate, and much of it has in

Jan 1, 1912

By A. W. Mitchell

Barite occurs as bedded and vein-type deposits in Nevada along a north-northeast trending zone that Parallels the Antler orogenic belt. The Nevada bedded deposits presently supply 85% of domestic barite production, used primarily as a weighting agent in the petroleum drilling industry. The ore bodies are controlled structurally and stratigraphically along regional and local structural breaks in siliceous eugeosynclinal rocks of lower to middle Paleozoic age. Evidence for the origin of the barite includes sedimentary and hydrothermal features, indicating that localization probably took place along fractures in the sea floor.

Jan 1, 1982

By D. F. Coolbaugh

Asia, the largest and most populous continent, has had little political influence on world affairs until very recently. The picture is rapidly changing. Although the cultures of various Asian countries differ widely, today they are united in their desire to industrialize. This desire is the key for expansion of Asian mineral production. The following discussion deals primarily with the situation in the south and southeast Asian countries -India, Pakistan, Burma, Thailand, Cambodia, Laos, South Vietnam, Malaya, and Indonesia.

Jan 10, 1960

By L. M. Clarebrough, A. K. Head, G. W. West, M. E. Hargreaves

RECENTLY Welber and Webelerl reported that during the annealing of fatigued copper no energy was released, but that energy was absorbed in the range of temperature 250" to 400°C. In view of the fact that strain hardening occurs during the fatigue of copper, this result was surprising and it seemed desirable to check the measurements. This note describes measurements made by a different technique which indicates that energy is stored during the fatigue of copper. Two test bars with gage length ¾ in. in diameter and 6 in. long were machined from OFHC copper and annealed in vacuum for 1 hr at 600°C. These were fatigued to fracture in an Avery pulsator at a frequency of 2000 cycles per min. The first specimen fractured after 0.25x10 cycles under a push-pull

Jan 1, 1956

By George W. Mitchell

THE property of Eureka Corp. Ltd. is located in the approximate geographic center of Nevada, 2 miles from Eureka, the county seat. The great sources of power, the Colorado, Snake, and Salmon Rivers and the rivers of northern California, are 300 to 500 miles distant, and no lines serve areas closer than 150 miles. Fuel for diesel and steam generation is available in Utah, 300 to 400 miles to the east. Eureka's railhead is 80 miles north where two trunk lines cross the county. A spur line serves Ely, 77 miles east. Good highways connect Eureka to the railheads.

Jan 8, 1953