Search Documents

By S. R. Goodman, Hsun Hu

A detailed study of texture developmenf in poly crystalline copper atzd 70-30 brass has been completed. Textural changes as a function of deformation are shoum by pole jigmres and by intensity measurements oF- various rejlectiotzs from the rolling plane and the rolling direction. These examinations were accompanied by measurements of stacking fault frequency, hardness changes, and microstructure. Some of the results were briefly presented earlier. Additional results reported here are consistent with the idea that deformation faulting or slip by partial dislocations is of primary importance in the formation of deformation textures in fcc metals. lo examine the idea that deformation faulting is of primary importance in determining whether the texture is the copper type or the brass type an extensive study of the development of polycrystalline textures in copper and 70-30 brass was initiated. Besides the determination of complete pole figures, the intensities of the various reflections from both the rolling plane and the plane perpendicular to the rolling direction, the peak shifts due to deformation stacking faults, and the hardness of the rolled specimens were examined at various reductions from 10 to 99 or 99.5 pct. Mi-crostructures were examined by transmission electron microscopy. Some of the results were briefly presented in an earlier publication.' Since then, additional information has been obtained. This is given in the present paper. EXPERIMENTAL PROCEDURE Material and Specimen Preparation. The material used was a commercial electrolytic copper bar 1i in. wide and 2 in. thick and a 70-30 brass bar la in. wide and 1i in. thick. Chemical analysis indicated a purity of 99.97 pct for the copper, with 0.025 pct 0 as the major impurity. The 70-30 brass was of higher purity with 0.0016 pct 0 as the major impurity. Extreme care was taken in the preparation of the starting material to insure uniformly fine grains with a nearly random initial texture. The two bars were first cold-forged and then annealed to eliminate any original texture. The grains were then refined by several cold rolling (approx 30 pct reduction) and annealing treatments. The + -hr anneals were carried out in a salt bath at 390" to 440°C for copper and at 490°C for brass. The resulting penultimate grain size was 0.06 mm for copper and 0.03 mm for brass, and both showed very little preferred orientation. The number of prior cold rolling and annealing cycles was such that the final thickness after various final reductions of 10 to 95 (for brass) or 99 (for copper) pct was the same (0.020 in.). These annealed strips were rolled in two directions by reversing end for end between passes according to the following schedule: 0.006 in. per pass to 0.100 in., 0.003 in. per pass to 0.050 in., 0.002 in. per pass to 0.025 in., 0.001 in. per pass to 0.020 in. Texture Determination. The development of rolling textures was studied by examining complete pole figures determined from the (111) reflection. Specimens thinned from one face of the strip to half thickness (0.010 in.) were used to obtain the central portion of the pole figures, while specimens thinned from both faces to 0.003 in. were used to obtain the peripheral portion. The reflection and transmission techniques have been described previously. In addition to X-rav pole figures, texture development was also studied b; examining the intensity variation of the (Ill), (200), (2201, (311), (331), (420), and (442) reflections from the rolling plane and from the plane normal to the rolling direction, as a function of deformation. The same specimens used for the central portion of the pole figures were used for the intensity measurements of the various reflections from the rolling plane. For intensity measurements from the plane normal to the rolling direction, composite specimens were prepared by mounting sections cut parallel to the transverse direction of the strip. An epoxy resin was used to bond these sections together, and the entire composite was then mounted in a cold-setting resin to facilitate subsequent polishing and etching to remove distorted metal at the cut. The intensities were expressed in units of the integrated intensities measured from an annealed copper specimen having almost no preferred orientation. Stacking Fault Frequency Determination. Following the analysis of Warren: the stacking fault frequency, a, was determined from the change in the peak separation (A%) of two neighboring reflections of a deformed specimen, as compared with the normal peak separations of a fully annealed specimen. To obtain sufficient intensities for the second-order reflections, (222) and (400), composite specimens were prepared from parallel sections cut from the strip at 30 deg to the rolling direction for copper and 25 deg for the brass.* From texture data, these sections are known to contain a large population of both (111) and (200) planes. Since residual stresses can also cause X-ray line shifts (the direction of line shifts depends upon the sign of the stress), the use of composite specimens consisting of sectioned planes should help compensate for these effects as the residual stresses change sign from the surface to the central section of a rolled strip. Since the amount of peak shift is almost un-measurable in brass rolled 15 pct and in copper rolled

Jan 1, 1969

By C. H. G. Bushell, James E. Lawver, William Barbarowicz

Proper use of automatic controls in the process industries is a combination of art and science. Although many phases of automatic control theory can be expressed by precise mathematical relationships, the final control arrangement usually requires considerable effort by trial and error before the optimum control circuit is found. The failure of flotation operators to recognize that control circuits require study and plant experimentation before satisfactory operation occurs has led to a popular misconception that flotation plants simply do not lend themselves to automation. This widespread belief has been overcome to some degree in recent years by the numerous installations of automatic controls that have paid their way by increasing profits in terms of increased recoveries, lowered costs, or higher grade concentrates. WHY CONTROL ? Any form of automation must be justified in terms of ultimate return on in- vestment by improving quality, by increasing plant throughput, or by reducing the total operating costs. Generally speaking, automatic controls rarely re- place a mill operator. They assist the operator in holding important variables within predetermined limits. Large tonnage operations usually can justify a great deal of automation because an increase in one or two units of recovery results in enormous savings compared to the capital and operating costs of controls. DETERMINATION OF CONTROL The first questions in considering plant automation are: 1) What variables must be controlled? 2) What are the optimum levels of the variables? The optimum operating conditions for any process are those which maximize profits. Many of the variables active in flotation processing can be determined by experimentation in the laboratory or pilot plant 10. Although laboratory experiments can pinpoint variables, the true optimum conditions existing at plant level usually must be determined by plant scale experiments. In recent years, the concepts of detailed experimental designs in the laboratory, followed by plant experiments, have reached the stage of maturity where

Jan 1, 1962

By C. C. Harris

A critical literature review leads to a descriptive model of tumbling mill operation based upon energy partition concepts and the necessary requirements for particle fracture. As grinding proceeds into the ultra-fine region, conditions which are of little significance during normal operations gradually become controlling. These involve increasing resistance to fracture and an increasing tendency to aggregate as particles become smaller, and a growing fraction of the power input being consumed fruitlessly. The result is that fineness asymptotes to a maximum value as comminution proceeds indefinitely; thus where t is time, p and n are experimentally determined parameters, and Ø is a measure of fineness, which is presumed to be proportional to specific surface area, or proportional to the reciprocal of the size modulus (provided that the distribution modulus remains constant with time), or both. Ø, is the asymptotic value of Ø and is a measure of the grind limit. A method for its graphical determination is given. In a previous paper1 the physical and mathematical principles requisite to a study of the role of energy in comminution were reviewed. The micro-process of comminution — or the comminution event — can be investigated in terms of (a) the magnitude of the force-field localized around the individual particles which gives rise to the stresses generated in the particles, which in turn induces their fracture, and (b) the distribution of fragment sizes, should the event prove fruitful. The entire fragmentation operation can be considered to be the totality of its individual events, and in order to obtain a single independent variable of the process it is necessary to transform and sum the local stresses in terms of energy.1 This energy, however, will account for only a fraction of the energy input to the comminution process, the actual magnitude depending upon the kind of mill and several related factors. From the comminution viewpoint the primary function of a mill is that of stressing as many as possible of the individual particles of the charge to failure, with the maximum economy of energy expenditure. This is difficult indeed to achieve, for stressing a particle does not always break it, while the overwhelming portion of the energy input is involved with various internal mill processes which — almost incidentally — determine the magnitude, frequency, and manner in which the forces are applied to the particles. Essentially, these processes depend upon the mill dimensions, loading and speed, and they may be little affected whether fracture occurs or not. These processes must be delineated if a complete description of the role of energy in comminution is to be given; the energy account sheet1 (Fig. 1) in showing how the energy is partitioned for the requirements of the several functions it performs, provides a framework for the development of a model of the comminution process. Actual numerical values for the variables appearing in Fig. 1 will depend upon the mill, materials, and operating conditions. A possible general relationship between the variables will be suggested in this paper. Before proceeding further, a cautionary note must be issued. It was pointed out in an earlier paper' that while energy input is not changed by increasing the power and decreasing the time in the same proportion, and vice versa, the results of the process in terms of particle fineness may be different. Thus, although energy is chosen as the independent variable of a comminution process, it is not absolutely independent, and care must be exercised to ensure that it is used within its range of valid application. Time has the necessary independence, and it will be used in place of energy where it is appropriate. The residence time in a mill is usually of the order of minutes. Under these conditions the particles are subjected to "... a relatively constant fracture producing environment".2 However, under the more rigorous conditions of greatly extended time, which pertain in ultra-fine grinding, indications are that the fracture producing environment no longer remains constant; this is the major subject of this paper. At this extreme limit the mill is probably taxed to its utmost, and at the same time the bulk material properties are becoming closer to ideal, while the physico chemical effects associated with surfaces, edges and corners are multiplying. (The edge length per unit volume is proportional to the square of the specific

Jan 1, 1968

By A. E. Belton

The individual projections for large mines in the Pittsburgh coal seam in northern West Virginia are discussed with emphasis on roof control and ventilation requirements. All four mines use continuous miners with panel belts and rail for main line haulage. Both development and retreat-type mining are covered. There are a variety of mining projections being used currently in northern West Virginia. To discuss each would be impossible, so an arbitrary cross section has been selected in an attempt to indicate a fair degree of representation. Four mines, hereinafter referred to as Mines A, B, C and Dl will be discussed separately. The greater part of northern West Virginia coal production is mined from the Pittsburgh seam. This is the seam worked by all the mines discussed here. Although the coal bed outcrops at the eastern and southernmost points, these mines are all working in a depth ranging from 400 to 1400 ft below the surface. Some steep gracles have been encountered but are only considered local in nature; the overall average dip of the seam is 1 1/2 % northwest. In each of the operations the particular mining scheme used has proved advantageous, since they have been designed to satisfy particular equipment and/or physical condition requirements. So regardless whether such projections utilize a partial or full recovery principle, the productivity performances appear better than average. MINE A Full retreat is the basic mining approach for mine A, although current mining is primarily in the entry-driving stages to expand territory in preparation for pillar work. Only one section unit now on retreat. The average clean coal production at this mine is 7000 tons per day. Initially, a ripper-type miner was used for development at this mine. But with a rather weak roof overlying the coal bed and the greater horizontal span left at the top by a ripper machine, roof control became a critical problem. Even though roof bolts were used concurrently in the mining cycle for initial support, the majority of the roof in these entries

Jan 1, 1962

By Augustus Locke

San Francisco Meeting, October, 1911.) Two Opposed Interpretations of the Tonopah Structure.-The important geological publications concerning the Tonopah mining-district are those of Spurr 1 and of Burgess.2 In these publications are presented fundamental differences of interpretation, which are the more interesting because both authorities have had ample opportunity for observation, and because both are geologists of proved ability. I was vastly puzzled to know which had the better of it, and in order that I might reach a conclusion in my own mind, I recently spent some time in the district going over the physical evidence. Surprising as it may seem, this evidence looks agreeably conclusive. A review of it will, I believe, be of interest to those who are familiar with the previous publications. The general geological features of Tonopah are shown in Fig. 1, and the differences of interpretation referred to are outlined in the accompanying notes. Briefly, Burgess regards the various rocks as flows, lying in the order of their deposition. Spurr regards them in part as flows, and in part as flat-lying intrusives. The disagreement, then, concerns the rocks regarded on the one hand as intrusives, and, on the other hand, as flows. These rocks are chiefly the so-called calcitic andesite, the upper rhyolite, and the lower rhyolite. Economic Importance of the Question of Interpretation.-The economic importance of the question of interpretation is, of course, limited to its bearing on the probable distribution of 1 Geology of the Tonopah Mining District, Nevada, Professional Paper No. 42, U. S. Geological Survey (1905). Report on the Geology of the Property of the Montana-Tonopah Mining Co. (1910). An abstract of this report is given in the Mining and Scientific Press, vol. cii., No. 16,p. 560 (Apr. 22, 1911). 2 The Geology of the Producing Part of the Tonopah Mining District, Economic Geology, vol. iv., No. 8, pp. 681 to 712 (Dec., 1909).

Feb 1, 1912

By G. W. Bain

The Canadian magnesite deposits are situated in Grenville township, about 8 miles from Calumet station, on the Canadian Pacific Railway, but the poor transportation facilities have hindered their development. Magnesite was discovered in the boulders near White Rock Lake by Rev. W. P. Boshart in 1900. Observing that the material of these boulders was more glistening and whiter in color than Grenville limestone, he sent a specimen to the Department of Mines, Ottawa. An analysis showed this to be almost pure carbonate of magnesia and of commercial value if present in sufficient quantities. That summer, Boshart and McAllister found numerous outcrops, both of boulders and of bed rock, that gave promise of being magnesite of a commercial grade, and decided that this mineral deposit, if developed, would rival that at Veitsch, Austria. So they procured options on most of the land on which they knew the magnesite occurred. But the transportation difficulties were too great for the deposits to be mined at the prices offered for the product. In 1907, T. J. Waters organized the Canadian Magnesite Co. and opened a quarry on the north half of lot 18, range IX, and later on lot 15, range IX, of the same township. A lirnestone kiln was erected and the calcined rock was hauled to Calumet. In 1914, the North American Magensite Co, took over the quarries and shipped both crude and calcined magnesite until January, 1923. During 1915, S. Melkman organized the Scottish Canadian Magnesite Co. and opened a quarry on lot 15, ranges X and XI, Grenville township. A light, narrow-gage railway connects this quarry with the C. P. R. at Magnesite station. but shipments are made only during the summer months. Numerous other quarries have contributed to the output of the district but the greater part has come from the open pits of the

Jan 1, 1923

By G. W. Bain

The Canadian magnesite deposits are situated in Grenville township, about 8 miles from Calumet station, on the Canadian Pacific Railway, but the poor transportation facilities have hindered their development. Magnesite was discovered in the boulders near White Rock Lake by Rev. W. P. Boshart in 1900. Observing that the material of these boulders was more glistening and whiter in color than Grenville limestone, he sent a specimen to the Department of Mines, Ottawa. An analysis showed this to be almost pure carbonate of magnesia and of commercial value if present in sufficient quantities. That summer, Boshart and McAllister found numerous outcrops, both of boulders and of bed rock, that gave promise of being magnesite of a commercial grade, and decided that this mineral deposit, if developed, would rival that at Veitsch, Austria. So they procured options on most of the land on which they knew the magnesite occurred. But the transportation difficulties were too great for the deposits to be mined at the prices offered for the product. In 1907, T. J. Waters organized the Canadian Magnesite Co. and opened a quarry on the north half of lot 18, range IX, and later on lot 15, range IX, of the same township. A lirnestone kiln was erected and the calcined rock was hauled to Calumet. In 1914, the North American Magensite Co, took over the quarries and shipped both crude and calcined magnesite until January, 1923. During 1915, S. Melkman organized the Scottish Canadian Magnesite Co. and opened a quarry on lot 15, ranges X and XI, Grenville township. A light, narrow-gage railway connects this quarry with the C. P. R. at Magnesite station. but shipments are made only during the summer months. Numerous other quarries have contributed to the output of the district but the greater part has come from the open pits of the

Jan 1, 1923

By A.E. Martin, Gerhard Derge

IE the molecular constitution of molten slags were better known, the nature of chemical reactions in slags and between slags and metals could be better understood and as a consequence might be better controlled. Constitutional information can be obtained by studies on either the molten or the solidified slags. Valuable as the studies on solidified slags admittedly are for many purposes, especially as control methods in steelmaking, they are always of questionable value in giving information on the molecular constitution of liquid slags. However, the characteristics of molten slags such as viscosity, rates of dilfusion, and electrica1 conductivity can be determined experimentally and interpreted along with other knowledge on slag-metal and slag-gas reactions so as to provide direct information on liquid slags. Metallurgists are accustomed to regard reactions in molten slags as involving only neutral molecules, whereas it is quite possible that ionic constituents are actually involved. For example, the dissociation of calcium silicate usually is represented us Ca2SiO4 = 2CaO + SiO2 although a reasonable alternative would be to write Ca2SiO4 = 2Ca+2 + Si04-4 Such ionic dissociation has been suggested frequently without adequate experimental proof. This paper deals especially with electrical conductivity measurements on slags oi the blast-furnace type. These measurements were made to determine whether or not slags are ionized and, if so, to provide a qualitative estimate of the extent of ionization. Electrolysis experiments that indicate the identity of the ions present are also reported. Since the presence of ions has not been considered carefully in modern slag studies, the relevant literature will be reviewed. Review of Literature In 1906 Aikenl obtained a patent for a continuous process of producing iron electrolytically by passing a direct currenl through a bath of FeO.SiO2 to which iron oxide was added periodically to maintain a uniform concentration. The patent also included the addition of CaO and MgO to the bath to lower its melting point. The silicate melts involved were thus in the same system as basic open-hearth slags but with higher FeO and lower CaO contents. Electrical conductivity measurements were made on some molten silicates by Doelter2 in 1907. Natural silicates, such as

Jan 1, 1943

By A. E. Martin, Gerhard Derge

IE the molecular constitution of molten slags were better known, the nature of chemical reactions in slags and between slags and metals could be better understood and as a consequence might be better controlled. Constitutional information can be obtained by studies on either the molten or the solidified slags. Valuable as the studies on solidified slags admittedly are for many purposes, especially as control methods in steelmaking, they are always of questionable value in giving information on the molecular constitution of liquid slags. However, the characteristics of molten slags such as viscosity, rates of dilfusion, and electrica1 conductivity can be determined experimentally and interpreted along with other knowledge on slag-metal and slag-gas reactions so as to provide direct information on liquid slags. Metallurgists are accustomed to regard reactions in molten slags as involving only neutral molecules, whereas it is quite possible that ionic constituents are actually involved. For example, the dissociation of calcium silicate usually is represented us Ca2SiO4 = 2CaO + SiO2 although a reasonable alternative would be to write Ca2SiO4 = 2Ca+2 + Si04-4 Such ionic dissociation has been suggested frequently without adequate experimental proof. This paper deals especially with electrical conductivity measurements on slags oi the blast-furnace type. These measurements were made to determine whether or not slags are ionized and, if so, to provide a qualitative estimate of the extent of ionization. Electrolysis experiments that indicate the identity of the ions present are also reported. Since the presence of ions has not been considered carefully in modern slag studies, the relevant literature will be reviewed. Review of Literature In 1906 Aikenl obtained a patent for a continuous process of producing iron electrolytically by passing a direct currenl through a bath of FeO.SiO2 to which iron oxide was added periodically to maintain a uniform concentration. The patent also included the addition of CaO and MgO to the bath to lower its melting point. The silicate melts involved were thus in the same system as basic open-hearth slags but with higher FeO and lower CaO contents. Electrical conductivity measurements were made on some molten silicates by Doelter2 in 1907. Natural silicates, such as

Jan 1, 1943

By J. S. Levine, M. Prats

A homogeneous and uniform cylindrical reservoir containing oil and gas is fractured vertically on completion and is produced at a constant bottom-hole pressure. The fracture has an infinite flow capacity, is of limited lateral extent and is bounded above and below by the impermeable strata defining the vertical extent of the reservoir. Results show that such a fractured reservoir can be represented by a reservoir of circular symmetry having very nearly the same production history. The well radius of this circular reservoir is about 1/4 the fracture length and is essentially the same as that obtained previously for a single fluid of constant compressibility. At the same value of cumulative oil production, gas-oil ratios of fractured reservoirs producing at constant terzinal pressure are larger than those of reservoirs having no fractures. This leads to more inefficient use of the reservoir energy in fractured wells and results in lower reservoir pressures for the same cumulative oil production. The reduction in operating life due to fracturing a reservoir is not as great as that for a slightly compressible fluid. This diflerence can be accounted for by the lower reservoir pressure in the fractured reservoir and its adverse effect on the average mobility and compressibility of the oil. As anticipated, the reduction in operating life increases czs the reservoir permeability decreases. The type of results presented in this report can be used to determine the economic attractiveness of fracture treatments per se, to setect the initial spacing to be used in developing a field, and to compare the relative merits of fracturing available wells and infill drilling. INTRODUCTION The effect of vertical fractures on a reservoir producing either an incompressible or a compressible liquid has already been discussed in the 1iterature.l,2 Those results indicate that the production history of such a reservoir is essentially the same as that of a circular reservoir having an effective well radius of approximately one-fourth the fracture length. The present work reports on the effect of a vertical fracture on a reservoir producing two compressible fluids —oil and gas—by solution gas drive. Because of the empirical nature of the PVT and relative permeability data used to obtain the performance of such reservoirs, results can only be obtained numerically and with the aid of high-speed computers. Since reservoirs lose their radial symmetry when fractured vertically, pressure and saturation can no longer be given only in terms of distance from the well. Two coordinates (such as x and y) must now be used to describe the pressure and saturation within the reservoir, and, since we are dealing with compressible fluids, time is also a variable. Thus the solution of a vertically fractured reservoir requires finding two unknowns (pressure and saturation) in two space variables (say x and y) and in time (t). Since no means are readily and generally available for solving such problems at the present time, we have used the results of previous work1,2 to approximate the effect of a vertical fracture on a reservoir producing both oil and gas by depletion. The purpose of the present wmk, then, is to investigate the possibility of using available numerical techniques (limited at the moment to one space variable) to study the two-space-variable flow behavior resulting from a vertical fracture. Results obtained in the course of this investigation are also reported and discussed. Input and output data of the numerical methods used are given in practical units: BOPD, feet, psi, cp, and md. Results are discussed fist in terms of specific reservoir and crude properties and geometries. Later, dimensionless parameters are introduced in order to extend results to different values of some of the reservoir and fracture properties. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The reservoir has an impermeable, circular, cylindrical outer boundary of radius r,. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below' the producing layer (reservoir). It is assumed that there is no pressure drop in the fracture due to fluid flow. 1 indicates the general three-dimensional geometry of the fractured reservoir. Gravity effects and the effects of differential depletion resulting from variations in hydrostatic head (pressure) will be neglected. Thus, the flow behavior in the fractured reservoir is described by the

By J. B. Newkirk, D. L. Martin, A. H. Geisler, R. Smoluchowski

A FUNDAMENTAL investigation of the mecha-nism of the ordering reaction and of the accompanying changes in properties has been undertaken, since an extensive study of this process could well contribute to the knowledge of phase transitions in alloys. Cobalt-platinum alloys were chosen for the study since they exhibit interesting and unusual permanent magnet properties.1,2. In addition, the ordering reaction in cobalt-platinum alloys is a convenient one to study experimentally because of the high maximum ordering temperature, the large difference in the X-ray scattering power of cobalt and platinum atoms, and the relative ease with which the alloys can be plastically worked into wire and strip. In the early stages of this study, it became apparent that the published phase diagrams&apos;, &apos; of the cobalt-platinum system contained questionable features, in the region of 40 to 60 atomic pct Co, which were considered in another publication by the authors.4 That portion of the research reported elsewhere on the equilibrium states of cobalt-platinum alloys does not confirm the presence of a previously reported, high temperature disordered tetragonal phase and a low temperature body-centered cubic phase. On the other hand, the structure of the ordered phase is face-centered tetragonal with an atomic distribution analogous to that of CuAu.4 This lattice forms from the disordered face-centered cubic phase in such an orientation that the <100> directions are parallel to the <100> direc-tions of the disordered phase. At compositions other than the ideal 50 atomic pct the ordered phase can exist in equilibrium at high temperatures with the disordered phase. A Widmanstatten pattern of plate-like particles of the ordered phase parallel to (110) planes of the disordered matrix is observed when an initially disordered alloy is held at these temperatures. The temperature range of the two-phase region has been determined for three alloys by X-ray diffraction analyses, microscopic examination, and electrical resistivity measurements, and these results are incorporated with some of those of Gebhardt and Köster in the revised phase diagram of fig. 1. The purpose of the investigation reported here was to examine the mechanism of ordering in co-balt-platinum alloys by X-ray diffraction and metal-

Jan 1, 1951

History of Reverberatory Smelting in Montana, 1879-1933. By FREDERICK LAIST (Trans, vol 106 31,800 words ) The development of the art of reverbera¬tory smelting from 1879, when smelting first started in Butte, up to the present time is described. The paper traces the development of the reverberatory furnace, as regards both constructing and operating, from the initial 10-ton furnaces to the present-day 600-ton furnaces and the changes in operating practice which accom¬panied the gradual enlargement of the furnaces and the reasons therefor are described and explained The results obtained from an investigation (made in the course of the Carson litigation) into the various methods of charging reverberatory furnaces are given These investigations proved that the method of charging a reverberatory had very little to do with its performance It was also found, at the same time, that the depth and extent of the bath maintained in the furnace had very little to do with its performance Numerous operating results are included and the article is illustrated Development of Copper Converting at Butte and Anaconda. BY WILLIAM KELLY AND FREDERICK LAIST (Trans , vol 106 4400 words.) This paper is based on recollections of one of the authors, W M Kelly, who has been identified with the development of smelting and converting at Butte and Anaconda since early times The article starts with a description of the circumstances surrounding the first intro¬duction of copper converting at the Parrot Works in Butte under the Manhes patents It briefly recounts the difficulties which were encountered and the steps taken to overcome them Among these were the absence of means for punching tuyeres in the original converter This difficulty was overcome crudely by drilling holes in the windbox opposite the tuyeres, said holes being closed by wooden plugs Later these plugs were replaced by steel slides and still later by the Dibblie ball valve, which has remained standard ever since The development of the converter from both struc¬tural and operating standpoints is traced from the early beginning to the present day Developments in Lead and Copper Converting at Tooele. BY B L SACKETT (Trans, vol 106. 3900 words) This paper shows the development at this Utah lead and copper smelter from separate converting of the two kinds of matte produced to a more efficient and economical treatment of the combined mattes This was accompanied by the use of relatively large amounts of silicious ore in the converting of lead matte as well as copper matte, which greatly improved the quality of converter slag produced, both from the standpoint of its copper content and its desirability for

Jan 1, 1935

By Frank Peterson

THE manufacture of gasoline by extraction or precipitation from the natural gases in which it is found, the present status of. the industry, its past development and future extensions; offer a subject which is so broad that to handle it in its entirety would require a voluminous paper. The writer will, therefore, attempt to concentrate the essential matter of the subject for a general presentation, giving some of the most interesting details of the factors that are important to the industry. This industry has drawn liberally on the principles of physics and chemistry, and, to a large extent, has had to adapt such information as is most useful-not from data recorded with reference to petroleum, but from data recorded with reference to general treatment of other materials. Because of the complex character of the petroleum series of hydro-carbons and the fact that data, such as solubilities, vapor pressures, etc., of the different petroleum compounds have not been determined, we are still working by rule of thumb in. some essential phases of the industry. Furthermore, the difficulties of determining such data are almost insurmountable. We have not one,, but two butanes to deal with-not one, but several, pentanes, hexanes, heptanes, and, as we ascend in the series the complexity and multiplication of isomers increases at such a rate as to make the task of isolating and studying their physical characteristics almost beyond the hope of possible attainment. The industry is the connecting link knitting the interests of oil producers and refiners into a much closer relationship than ever existed .prior to its inception and development. The relation between the producer and the refiner of petroleum prior to 1910 was. a rather antagonistic one in a commercial sense. It was to the interest of the producer of crude petroleum to sell it for a maximum consideration; the refiner&apos;s interest was to obtain the same product for a minimum consideration; therefore, each side of the business transaction retained within his own hands as far as possible the trade secrets of his business. Each side maintained an attitude of cold-blooded business sympathy only for the other. Cas-

Jan 12, 1917

The negative charges on diaphragms of quartz, tungstic oxides, stannic acid, acid dyestuffs, soaps, and glass have for a number of years been explained on the basis of chemical equilibria—a hydrogen ion or light metal ion passes into solution leaving the solid complex ion negatively charged. While there are a number of observations which indicate a proportionality between the ( potential and the streaming potential it should be recognized that all the experimental evidence thus far presented shows that if hydrogen ion concentration is kept at a constant value, electrokinetic phenomena are influenced by salts. The multivalent ions exert the greatest effect on the reduction of osmotic flow. In the interpretation of all electrokinetic data the assumption is made that the potential of the solid remains constant. That this is not true is evidenced by the values of [ potential for quartz in contact with conductivity water as reported by the several investigators and by the authors of this paper. It is apparent that the nonreproducibility of surfaces will always prevent the obtaining of exactly comparable data. At best the experimental technique described depends on a theory which is capable only of showing a trend—another quartz surface should exhibit similar but not identical potential curves. It seems entirely reasonable to assume that the negatively charged laurate ions should have little or no attraction for a negatively charged quartz surface. The weight of previous experience in selection of flotation activators points unerringly to the usefulness of the multivalent metallic ions. The primary reason why the divalent barium ion is not available to two negative charges on the quartz surface might easily be that of distance between such adjacent negative charges. Otherwise activation could not occur, and the quartz could not assume the remaining unit positive charge of the barium ion. For this case no electrical double layer theory seems necessary. Clearly this is, at the negatively charged quartz surface, a case of partial chemisorption of the cationically divalent barium ion followed by the anionic neutralization of the remaining cationic charge by the freely moving laurate ion. It is hoped that the authors will continue with this interesting technique and that their results will continue to indicate trendwise what is known about the

Jan 1, 1957

By B. Rao Pothini, Hilmar A. von Schonfeldt

One of the key elements essential to a productive and uninterrupted longwall mining operation is roof control. In several of the Island Creek Coal Company&apos;s mining sections, polyurethane has been infused 80 into strata to control severe roof failures in the face and gate entry areas. To date about 50,000 kgs (110,000 lbs) of the chemical have been consumed in a number of applications. Roof-to-floor convergence 60 and differential roof sag have been monitored to determine the need for polyurethane infusion and also to evaluate roof stability following the infusion. Stratascopic observations of the roof formed the basis 40 for confirming the need and also for estimating the required quantities of polyurethane. Both chemical infusion and roof control monitoring techniques have been applied successfully under very adverse roof 20 conditions; substantial production benefits have been realized. Operator acceptance of the system has been very good.

Jan 1, 1981

By C. E. Shoenfelt

The most important development in an otherwise colorless year in Colorado oil fields was the completion, late in 1933, of a well on Iles dome on the western slope of Colorado, with an initial production of 1100 bbl. of oil. No great amount of activity beyond the drilling of necessary offset wells is to be expected as a result of the completion of a well of this size because the acreage on Iles dome is closely held; there is no pipe line outlet other than to the Texas Company&apos;s small refinery at Craig, 24 miles distant; and the market for the oil is limited to the demands of sparsely settled communities in the high mountains. The Iles field is located on a large dome developed in Mancos shale of Cretaceous age, and having a closure of approximately 400 ft. The structure is highly faulted on the southern end. The first commercial oil well on this dome was completed by the Midwest Refining Co. on the south side of sec. 22-4N.-92W. Oil of 37" gravity was developed in Nancos shale at 2560 ft. and water in the Dakota sandstone at 2630 ft., but a considerable amount of additional oil was found in the shale immediately overlying the Dakota. From 2630 ft., the well produced in 16 hr. 750 bbl. of fluid, 33 per cent of which was water. Production in the Sundance sand of Jurassic age was found in the Midwest Refining Company&apos;s No. 4 Parkinson, in the NE.-SW.-SE. of sec. 22-4N.-92W., and completed on the last day of the year 1926, for an initial production of 450 bbl. of oil at a total depth of 3242 ft. The well completed in 1933 is also a Sundance sand producer and was finished at a depth of 3447 ft. It extends the productive area of the field about a quarter of a mile cast. The Iles field is said to have a potential production of 5000 bbl. of oil a day from its present wells, but for the past year has been held at about 600 bbl. a day. The most important test, stratigraphically, ever drilled on the western slope of Colorado is the California Company&apos;s No. 1 Raven, NW.-SE. of sec. 30-2N.-102W., which had an initial production of 138 bbl. of oil of 32" gravity, in the Weber formation (Pennsylvanian) between 5750 to 6315 ft. It mas drilled to 7137 ft., probably near the base of the Weber, and then plugged back to 6315 ft. It was shot quite heavily with nitro-glycerin, but failed to respond. While the well can hardly be classified

Jan 1, 1934

By T. Sterry Hunt

BUT little was known of the coals of Southeastern Ohio until the present survey of the State under Dr. Newberry began its work. The results of the geological investigations of Prof. E. B. Andrews in this region, and of the chemical investigations of Prof. T. G. Wormley, both of which appear in the reports of the survey for 1869 and 1874, and more recent special reports by the former, together with some data for which I am indebted to the kindness of Dr. Newberry, and my own limited observations, have served me for the preparation of the following notice of the coals lying on the western border of the great Appalachian coal-basin in the region drained by the Hocking River and its tributaries, and belonging to the Lower Coal-Measures. Some uncertainty exists as to the place in the succession of the lower coals to be assigned to the seams known and mined in the Hocking Valley. It is the opinion of Prof. Andrews that the inequalities of the original surface were such that we cannot identify in that region the lowest coals known in Northwestern Pennsylvania and the contiguous parts of Ohio, but that we must rather count from above downwards. These conclusions Dr. Newberry is not prepared to accept, and further researches will be necessary before certainty can be attained in this matter. Meanwhile it seems, from a study of its relations to the Pomeroy or Pittsburgh seam, that what is known as the great vein of the Hocking Valley, occupies the horizon of the Upper Freeport coal, E of the Pennsylvania survey, or No. 6 in Dr. Newberry&apos;s enumeration, counting from the base. This seam, in the region in question. assumes certain characteristics which, taken in connection with its geographical position, give it a great importance among the coals of the State. The area to be noticed includes the whole or parts of several townships in Perry, Hocking, Vinton, and Athens Counties, lying near the margin of the basin over which the vein in question assumes the character of a dry-burning or splint coal, and has a thickness varying from six to ten and even twelve feet. Its precise limit southward cannot at present be clearly defined, but it has been found as far south as the line of the Marietta and Cincinnati Railroad, with a thickness of six feet, and is mined at various points along the valley of the Hocking River, near Nelsonville, where it attains six or seven feet. To the northward, along the tributaries of this river, Sunday and Monday

Jan 1, 1874

By A. W. Ambrose

The underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of waterin;the base of an oil sand present a very serious problem to an oil company sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas. The purpose of this paper is to outline briefly1 general methods of analyzing oil-field water problems in a producing or in a producing and developing oil field, with a view to suggesting repair work on offending wells. Reference is continually made to producing oil wells; the same general method of procedure, however, should be adopted in a gas field.

Jan 1, 1921

By Hisaaki Takada, Atsushi Yoshida, Kazuo Satoh, Norikazu Nanko, Naoshichi Higashi

Kamioka Mine of Mitsui Mining & Smelting Co., Ltd. is the largest lead-zinc mine in Japan and is composed of two mines, Tochibora Mine and Mozumi Mine, which have daily production rates of 5,200 metric tons and 1,800 metric tons of crude ore respectively. In the mines, there are many massive pyro-metasomatic deposits which have been derived from the replacement of limestone. The deposits are composed of skarn minerals which mainly contain hedenberite. The country rock is generally hard and fine-grained gneiss. These deposits have been mined by means of the sublevel stoping method, induced block caving method and sublevel caving method at Tochibora Mine and mainly by the cut and fill method at Mozumi Mine. Since the 19601s, the trackless mining system has been introduced successfully into both mines, and is still promoted to be applied over wider areas. The underground hauling system is simplified remark- ably and much improved by adopting trackless ramps to the existing vertical and horizontal underground framework. Moreover, through the combination of the trackless mining system with the mining methods stated above, a notable increase in efficiency has been achieved. This is due to the high performance of the introduced machinery, reductions in man power of miscellaneous jobs, and also has enabled a highly efficient performance through its mobility. In addition, as it becomes possible to realize a flexible development to meet the irregularly shaped deposits and also becomes much easier to recover the remaining pillars by secondary mining, the extraction rate of ore has been improved considerably. With the introduction of the trackless mining system, the development method has been changed, thus former hand-hold leg-drills are now mostly re- placed by jumbo-type drills. Repair shops for Load-Haul-Dump machines also have been provided with an established service system. Reinforcement and rearrangement of the ventilation system has been carried out.

Jan 1, 1977

By I. H. Silberberg, R. L. Reed, O. K. Kimbler

interfacial films have frequently been observed at interfaces between certain crude oils and water. Several investigators have postulated that the presence of these films should influence the efficiency of oil recovery in water drive or waterflood operations. They may also influence the stability of emulsions which are sometimes a problem in petroleum production, and may be a factor in the fonation of paraffin deposits in oil well tubing and flow lines. This paper presents a technique with which a modified Langmuir film balance may be used to study the compressibility and collapse pressure of these natural interfacial films. Experimental data are presented for several nude oil-water systems. Data developed are used to infer the phase state of the film as a function of such variables as rate of reduction of interfacial area, ionic composition of the subtrate and pH of the subtrate. A film of known physical characteristics is shown to have a sinnificant effect on oil recovery from an unconsolidated sand pack. Possible applications of these results to petroleum production are discussed. INTRODUCTION The use of water to displace petroleum from reservoir rocks is of major importance both as a primary and a secondary recovery process. As water invades the rock, oil is completely displaced from some pores and left as a discontinuous phase in other pores. The manner in which water moves from pore to pore is strongly influenced by capillary forces. In view of the complexity of reservoir fluid systems, there can be little doubt that complicated interactions take place at both the liquid-solid and oil-water interfaces. One of the more interesting, and least understood, of the phenomena which take place at the oil-water interface is the formation of interfacial films. These films are believed to result from the adsorption of high molecular weight polar molecules at the interface.l.2 Presence of such molecules may cause a striking alteration in interfacial tension. When the oil-water interfacial area of certain crudes is rapidly reduced, a thin region (film) about the interface assumes the appearance of a solid membrane, and striations, wrinkles and gross distortions may occur. If such a film is solid, it should greatly alter the interfacial tension normally assumed to exist between the oil and water phases. If the membrane is continuous, a solid phase would separate the oil and water. Interfacial films between crude oil and water were observed in 1949 by Bartell and Niederhausers who commented upon the apparent rigidity of the films and their possible importance in the petroleum industry. Morrell and Egloff4 had earlier attributed the extreme stability of emulsions of sea water in fuel oil to very stable asphaltic films. Numerous investigators have observed rigid films in the course of crude oil-water interfacial tension determinations by the pendent drop method. Several investigators5,6,2 have separated inter-facially active materials from crudes and attempted to characterize them chemically. Reisberg and Doscher,2 using Ventura crude, showed the interfacial tension against water (as measured by the pendent drop method) to be affected by aging, contraction and expansion of the interface, and the pH of the water. These investigators attributed the adhesion of oil to a water-wetted surface and the distortions of flow paths in glass capillaries to the presence of rigid films. Dodd7 has studied the interfacial viscosity of adsorbed films and found them to be non-Newtonian in behavior. Craighead and Harvey8 reported a series of displacements in tubes packed with 60 mesh glass beads. They interpreted the results as indicating an effect of stearic acid films on waterflood recovery and imply that natural films may produce similar results.

Jan 1, 1967