Search Documents

By F. D. Rosi, F. C. Perkins, L. L. Seigle

An investigation was made of the mechanism of plastic flow in coarse grained specimens of both sponge and iodide titanium at low (-196°C) and high (500° and 800°C) temperatures. Deformation by slip occurs predominantly on a {1011} plane and in a <1120> direction over this entire temperature range, and secondary slip on {101-1} planes becomes more prevalent with overthisentireincreasing temperature.range, The crystallographic habit of the predominant twin planes becomes more prevalent with type is temperature-dependent, and deformation by twinning increases as the temperature of testing is lowered. Kink bands were not observed at -196OC and rarely at the high temperatures. A LTHOUGH the deform a tional mechanisms in . -titanium at atmospheric temperature have been extensively investigated," there is little information regarding the influence of testing temperature on these mechanisms. The only available data come from the recent work by McHargue and Hammond, who extended single crystals of iodide titanium at a temperature of 815°C. No significant changes in the types of slip and twinning planes were observed, but increased activity on the type I, order 1 pyramidal slip planes and on the type 11, order 2 twinning planes was reported. These planes contribute very little to the deformation process at room temperature.&apos;&apos; &apos; Since there is interest in titanium as a material for use at both low and high temperatures, the present investigation was undertaken to examine the slip and twinning behavior in coarse grained specimens of titanium at -—196", 500°, and 800°C in order to determine the general effect of temperature on the mechanism of plastic deformation. Experimental Material Used and Specimen Preparation—Both sponge and iodide titanium were used in the present investigation; chemical analyses appear in Table I. These materials were arc-melted under argon into 25 g slugs, which were then cold-rolled approximately 90 pct to a sheet thickness of 0.05 in. Since the strain-anneal technique was used for obtaining coarse grains, the cold-rolled sheets were made into tensile specimens which were then annealed to produce a relatively coarse uniform grain structure prior to critical straining. The details of the strain-anneal treatment. size of grains, and the method for preparing the specimen surface for optical microscopy have been described in a previous report.&apos; In order to obtain a wider spread in crystal orientation for the present work, it was necessary to vary the rolling schedule to reduce the degree of preferred orientation in the annealed sheets prior to critical straining. Methods for Tensile Testing—The apparatus for experiments at the temperature of liquid nitrogen (—196°C) consisted of two concentric stainless steel

Jan 1, 1957

By C. S. Simons

The conversion of a successful research and development effort into a money-making business venture requires careful attention. Problems of a business nature, such as market size, product selling price, raw materials and fuel availability and cost, financing factors, local and national taxes, licensing arrangements, etc. must, of course, be considered and resolved. In addition, the technical questions involving the scale-up of pilot plant or laboratory results to the full-scale plant must be resolved in order to avoid the financial disaster that attends a major delay in the startup of a commercial facility. The very difficult and demanding task of providing the interface between the research laboratory and the profitable metals processing plant will be discussed with examples from the author&apos;s extensive experience. After I had accepted the invitation to present a paper on the above subject of the interface between R & D and production operations, I began to give some serious thought to the subject. The program chairman had told me, in conveying the invitation, that what the committee had in mind was a discussion of positive and negative, forces in that interface, based on "gray-hair" experience. I am, therefore, at least physically qualified! My first reaction was one of mild shock; after over twenty years in the direct pursuit of the conversion of research and development findings into plant operations, I had never tried to sort out my , experience into a formal system of DO&apos;S and DON&apos;TS for the edification of posterity. However, after a little further reflection, I realized that this carries no stigma. No one has been able to formulate such a set of rules, and it is not really very likely to be done. Particularly if they are to be practical. I shall therefore settle for a more modest goal; I will simply discuss the factors that I have come to believe are the most critical in insuring that re- search and development results are converted into successful operation.

Jan 1, 1973

Important chemical and other technical engineering work necessary, for the prosecution of this war is being carried on by the Bureau of Mines Experiment Station, at Washington, D. C. The services of trained men of the following classifications are urgently needed Bacteriologists Instrument makers Biologists Laboratory Assistants Chemists, Inorganic Laborers Chemists, Organic Machinists Chemists, Physical Physiologists Chemists, Electro- Plumbers Chemical Engineers Steamfitters Draftsmen Stenographers. Electrical Engineers Skilled labor of various kinds If your training fits you for any of these occupations, send to the Bureau of Mines, American University Experiment Station, . Washington, D. C. for blank forms. When properly executed and returned by you, these forms will be placed on file, and when a vacancy occurs you will be considered for it and will be notified if your services are desired. If you are a registrant in the draft, and have not yet been- ordered to camp, it may be possible to have you immediately inducted into the service for work here. If you are not in the draft, but feel that you wish to serve your country in the present crisis, you can enlist, or serve as a civilian. Serve your country where you can serve it best. VAN H. MANNING, Director.

Jan 6, 1918

By H. R. Aldrich

This paper is not a treatise on the theory and practice of magnetic surveying. It presents a diagram upon which have been plotted observations taken with the simplest form of magnetic instrument, the lowly dip needle, over a large area astride the Lake Superior syncline of northern wisconsin. The exposures of the underlying formations are not sufficiently great in number nor fortunate in distribution to have provided the fuller understanding of the geology which has been secured by the use of the magnetic observations as an auxiliary tool or accessory in the hands of the geologist. The diagram (Fig. 2) in large part speaks for itself if studied in connection with the geological map (Fig. 1) for which it is the main control. It is presented to demonstrate the extent to which the use of such methods may aid in the solution of geological problems in a covered country. The diagram is probably unique in assembling the expression of such a wide range of formations, affected by so wide a range of secondary processes, and deformed by so many different structures in terms of magnetic variation. Few geologists outside of the Lake Superior country have had any first-hand experience in the taking of magnetic observations and the interpretation of the results in terms of geological conditions; nor have the Lake Superior men gone with the methods far afield from the mere tracing of iron formations. In more recent years the oil companies have gone heavily into investments in magnetometers, balances, and dip needles in the quest of concealed structural anomalies which are the favorable loci of petroleum accumulation. But these geophysicists come back from the fields with their collections of observations facing the question of interpreting the geological meaning of their magnetic anomalies. It is considered probable therefore, and certainly it is the hope of the writer, that the appended charts, or magnographs, which show how character of the country rock and its changes, structural strike and dip and their changes, depth of burial and its variation, contact metamorphic

Jan 1, 1929

By R. V. Lukes, H. W. Scheeline

Knowledge of a large number of the physical properties of the hydrocarbons is needed in the calculations and studies of the production engineer. Since experimental data on these properties of the individual hydrocarbons and their mixtures are available in only a relatively few cases, the use of generalized correlations has developed rapidly in the last decade. The generalized correlations of pressure, volume and temperature,&apos; enthalpy2 and vapor-liquid equilibria13 on the basis of reduced temperatures and pressures, are outstanding examples of this development. These correlations are of particular value to the production engineer interested in the flow of oil and gas, since they can be used to estimate the conditions under which segregation of phase occurs as well as the composition, density, and relative amounts of the phases. The technique of using the correlations for such estimations has been published by several authors4 and will not be considered in this paper. A considerable number of data have been obtained to check the generalized pressure-volume-temperature correlations, and these data indicate that such relations hold for the hydrocarbons from methane to heptane. The accuracy is in general sufficient for most engineering pressure-volume-temperature calculations. However, the generalized correlations of enthalpy and vapor-liquid equilibria have in general been developed from the pressure-volume-temperature correlations by thermodynamic calculations and only a relatively few experimental data are available to check these calculated values. The calculations from pressure, volume and temperature are likely to lead to large errors in the calculated enthalpy and vapor-liquid equilibria. Thus, in the calculations of enthalpies, slopes of the pressure-volume-temperature data are employed, and determining these slopes can greatly amplify small errors in the original data. In the vapor-liquid equilibria calculations it is necessary to have the pressure-volume-temperature relations of the mixture, and the latter propertics are much more questionable than those of pure components, particularly in the critical region. A considerable number of experimental data are

Jan 1, 1939

By R. V. Lukes, H. W. Scheeline

Knowledge of a large number of the physical properties of the hydrocarbons is needed in the calculations and studies of the production engineer. Since experimental data on these properties of the individual hydrocarbons and their mixtures are available in only a relatively few cases, the use of generalized correlations has developed rapidly in the last decade. The generalized correlations of pressure, volume and temperature,&apos; enthalpy2 and vapor-liquid equilibria13 on the basis of reduced temperatures and pressures, are outstanding examples of this development. These correlations are of particular value to the production engineer interested in the flow of oil and gas, since they can be used to estimate the conditions under which segregation of phase occurs as well as the composition, density, and relative amounts of the phases. The technique of using the correlations for such estimations has been published by several authors4 and will not be considered in this paper. A considerable number of data have been obtained to check the generalized pressure-volume-temperature correlations, and these data indicate that such relations hold for the hydrocarbons from methane to heptane. The accuracy is in general sufficient for most engineering pressure-volume-temperature calculations. However, the generalized correlations of enthalpy and vapor-liquid equilibria have in general been developed from the pressure-volume-temperature correlations by thermodynamic calculations and only a relatively few experimental data are available to check these calculated values. The calculations from pressure, volume and temperature are likely to lead to large errors in the calculated enthalpy and vapor-liquid equilibria. Thus, in the calculations of enthalpies, slopes of the pressure-volume-temperature data are employed, and determining these slopes can greatly amplify small errors in the original data. In the vapor-liquid equilibria calculations it is necessary to have the pressure-volume-temperature relations of the mixture, and the latter propertics are much more questionable than those of pure components, particularly in the critical region. A considerable number of experimental data are

Jan 1, 1939

By W. A. Gibson, Zay Jeffries

It has been known for a number of years that certain aluminum alloys could be hardened by quenching from a temperature of about 500&apos; C. Immediately after quenching the total increase in hardness is not marked, but the hardness increases gradually so that after about 4 days, it has reached a maximum. The actual increase in hardness probably continues for weeks or even months, but in order to detect the differences after 4 days, it is necessary to make tests at rather long intervals. So far as is known to the authors, Alfred Wilm was the first to discover these properties in aluminum alloys.&apos; The aluminum-copper alloys are amenable to this treatment and the addition of magnesium makes the heat-treatment effect more pronounced. Until recently heat treatment of aluminum alloys has been confined to the worked alloys in the form of sheet or extruded products. The alloy that has been most used in this connection is known commercially as duralumin and has about the following composition: copper not exceeding, 6 per cent.; magnesium not exceeding, 2 per cent.; manganese not exceeding, 1 per cent.; commercial aluminum,2 balance. A typically good alloy in this range consists of: copper, 4 per cent.; magnesium, 0.5 per cent.; manganese, 1 per cent.; commercial aluminum, balance. This alloy can be rolled into sheets or extruded; and in this condition it can be heated in the ordinary furnace atmosphere to a temperature near 500° C. and quenched in water. After about 4 days it will have the following physical properties: tensile strength 55,000 to 60,000 1b. per sq. in. (3866 to 4218 kg. per sq. cm.); elongation in 2 in., 15 to 20 per cent. No harmful effects of the furnace gases or even the air, if the heating is effected in an electric furnace in an air atmospherc.

Jan 1, 1921

By J. Ellzey Hayden

THE Cliffs Shaft mine of the Cleveland Cliffs Iron Co., located in the city of Ishpeming, Mich., is the largest producer of hard hematite ore on the Marquette iron range. The two shafts, A and B, lying 820 ft. (250 m.) apart on the east-west trend of the ore formation, were sunk in the early eighties, and, except for four years, have been steady producers of iron ore. Their location, on a hill overlooking the general offices of the company on the one side and the city of Ishpeming on the other, has made the shaft houses landmarks. In the spring of 1919, as the old wooden shaft houses had become shaky and out of line, and would soon be unsafe, it was necessary to replace them with the least possible delay. Three plans of construction were, therefore, considered: To replace the old shaft houses by somewhat similar structures made of wood; to use steel and radically change the design; or to build reinforced-concrete shaft houses outside of the wooden structures, completely enclosing them. The first plan was disapproved, because it is anticipated that the mine will have a long life and the proximity of other buildings makes the danger from fire rather great. Delay in receiving material, and the necessity for closing the shafts during erection, were other factors in the situation. The second plan was disapproved on account of the high cost of steel, slow delivery, and interference with hoisting during the period of erection. The presence near one of the shafts of a large bed of hard gravel suitable for concrete made, the cost of the third plan considerably less than the second, and little, if any, delay in hoisting was expected. Our expectations in this regard&apos; were fully realized. Furthermore, the work could be done by unskilled labor, which was plentiful, and the erection could be quickly started. When the proposition was submitted to Mr. W. G. Mather, president of the company, he recommended that, on account of the prominence of the buildings due to their location, an effort should be made to combine in the design as far as practicable something of architectural beauty. Following his recommendation, the original plans were submitted to the

Jan 8, 1920

By R. W. Waterfill

MANY existing ore deposits of valuable metals have been worked out in their upper surface levels and the continued productivity of these mines is dependent on their extension to greater depths in the earth. The maximum depths at present reached are about 6000 to 8000 ft. below the surface, with no evidence of an impoverished ore vein. These mines are widely distributed; some of the best known are in South Africa, Brazil, India and in the western sections of the United States. Among the factors which increase the difficulty of working these mines at increasing depths are hoisting, rock pressure and temperature. The manner and effectiveness with which these problems arc met will, no doubt, determine in a large measure the ultimate depths to which any mine can be profitably worked. The most critical of these three factors at present is the increase in temperature with depth. The high temperature and humidity in many of these mines at present are severely detrimental to the health of the workers and greatly hamper their efficiency. Some have almost reached a condition in which the human system cannot survive. The problems involved in the cooling and ventilation of mines have all been ably analyzed and presented in previous articles. For this reason, only a résumé of conditions affecting the cooling and conditioning of deep and hot mines will be given in this paper before attention is directed to possible methods of improving atmospheric conditions in the working levels. Physiological Effects of Temperature, Humidity and Air Motion Many data on the physiological effects of different atmospheric conditions on the human system have been compiled and published through the combined efforts of the American Society of Heating and Ventilating Engineers, the U. S. Bureau of Mines and U. S. Public Health Service. These data were not primarily developed around the conditions existing in deep mines, but the upper temperature limits of the investigations extend into, and are applicable to, mine atmospheric conditions. While the exact values of the standard comfort conditions, established for persons of such habits as those employed in detecting the different degrees of comfort, might not produce identical effects upon persons inured to

Jan 1, 1929

By James Gayley

The lining of the hearth and bosh of a blast-furnace has naturally come to be considered its weakest part, being subject not only to abrasion, but also to intense chemical action. In order to provide against rapidity of wear, it was formerly customary to build the lining from the mantle to the top first, and to put in afterwards the hearth and bosh, drawing the latter into a recess that had been reserved for it in the upper lining. At some works this practice still prevails ; but through the progressive development of cooling-devices, it has become possible to protect the bosh so well as to make it the most durable part of the furnace. The main question now is, by which one out of several methods the best economy results can be obtained. The plain bosh-jacket, made of wrought-iron or steel, and frequently called the air-cooled jacket, was a great improvement over the crinoline-construction formerly in vogue; but it was difficult in many cases to persuade furnace-managers, that in order to secure its best effects, they must discard the thick bosh-walls and put in comparatively thin ones. Mr John M. Hartman, who did more perhaps than any one to extend the use of these jackets, invariably contended for a 13-inch wall, the thin wall being an essential part of this construction. Later, a coil of pipe was placed just inside the jacket, through which water, circulating freely, contributed further to the proper maintenance of the walls. Undoubtedly much better results have been obtained in practice where the iron jacket has been supplemented by a coil in this way. It is safe to say that this combination of water-coil and jacket is much better than external sprays on the jacket; but it does not prevent the brick-work from cutting entirely away, which enlarges the bosh to that extent and interferes with the economy and output of the furnace. In case of leakage or stopping-up of the pipes, they cannot be replaced. A leading blast-furnace manager who is now using this construction

Jan 1, 1893

By Walter L. Maxson, Fred C. Bond

SINCE the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. STANDARD BALL-MILL GRINDABILITY TESTS The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill in all tests is 700 c.c. of the packed minus 6-mesh roll product, and the number of grams occupying 700 c.c. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter. Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I ½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity to be expected from a given mill is calculated by comparing the

Jan 1, 1943

By O. N. Carlson, H. A. Wilhelm, H. E. Lunt, J. M. Dickinson

On the basis of data obtained from microscopic examination, melting observations, cooling curves, X-ray analyses, and resistance measurements, phase diagrams have been proposed for the Th-Cb and Th-Ti alloy systems. Both are simple eutectic systems and have no terminal solid solubility or intermediate phases. The eutectic between thorium and columbium occurs at a composition of about 8 wt pct Cb and a temperature of 1435°C. The Th-Ti eutectic occurs at 1190°C at the composition 12 wt pct Ti. No change was observed in the transformation temperature of thorium in either system or in the titanium transformation. RECENT study of thorium and its alloys has been promoted because of the possibility of employing this metal in nuclear reactors. Their corrosion resistant properties, nuclear characteristics, and high melting points put columbium and titanium among the many metals being employed in the study of thorium alloys. Since a knowledge of the phase relationships would be important in the application of such an alloy, investigations were undertaken to propose phase diagrams for the Th-Cb and Th-Ti systems. Experimental Procedures Thorium metal sponge was specially prepared for use in this investigation. Carbon in a quantity less than 0.04 wt pct was the principal impurity. There was also less than 0.01 pct each of iron, calcium, zinc, aluminum, and nitrogen in the thorium. Columbium, both as a powder and sheet metal, was obtained from the Fansteel Metallurgical Corp. The manufacturer&apos;s specifications indicated that the metal contains less than 1 wt pct total impurities. An analysis of the metal showed approximately 0.18 pct C in the powder and less than 0.05 pct C in the sheet. The titanium used was commercial sponge, reported to be 99.5 pct Ti. An analysis showed that this metal contained 0.2 pct Fe. Preparation of Alloys—Since the metals used in this investigation are reactive and might become contaminated on melting in a refractory crucible, the alloys were prepared by arc melting. The titanium sponge was employed in the form of small lumps while the columbium additions were made either as pressed pellets of powder or as clippings from sheet. The alloying material and the thorium sponge were melted together under argon in conventional arc melting equipment employing a tungsten electrode and a water cooled copper crucible.

Jan 1, 1957

By R. V. McAfee

The fundamentals of vertical-lift performance are examined with the aid of computer-calculated flowing gradient charts. Flowing and gas-lift well performance characteristics are determined from available well test data. The effect of tubing size, gas-liquid ratio and wellhead pressure is discussed for both flowing and gas-lift wells. The effect of gas-injection pressure, formation gas, bottom-hole pressure and valve spacing is also discussed for gas lift wells. From these studies conclusions may be reached for improving or prolonging natural flow, obtaining optimum lift efficiency when natural flow ceases and improving existing gas-lift systems. The techniques perfected satisfy the requirement that the time involved to conduct an evaluation be practical for operating personnel. INTRODUCTION Flowing pressure gradients furnish the key to successful evaluation of vertical-lift performance in producing wells. Command of multiphase flow gradients in some readily usable form is a necessity before operating personnel can competently include vertical-lift performance evaluation of both flowing and artificial-lift wells in their over-all consideration of production efficiency. A readily usable form cannot be overemphasized since most of the decisions which confront the production engineer with a problem well must be made quickly. In moving a barrel of oil from the reservoir to the stock tank, the major portion of energy generally is expended in the vertical-lift phase. This may or may not be of concern during the flowing life of a well, depending upon the production requirements. It becomes of some concern when the flow performance of the well becomes erratic, and a conscious effort must be made to maintain natural flow. It is at this time that the first steps may be taken to modify existing conditions to relieve unnecessary limitations to proper flow. When natural flow ceases and some form of artificial lift must be installed, the amount of energy expended in lifting liquids becomes quite obvious. It is at this time, if no other, that lifting efficiency becomes important because that part which must be supplied from an outside source is now related directly as a cost per barrel of oil produced. Ten years ago, the majority of gas-lift wells were produced with gas-well gas. Today, the majority are produced by closed rotative gas-lift systems. This permits a direct evaluation of well performance in terms of horsepower requirements and has resulted in mixed conclusions as to the success of gas lift based upon the relative efficiency of a particular system. An increased awareness of the need to resolve vertical-lift performance on a readily usable, scientific basis was inevitable. An indication of the need for better applied science in this field is the often-asked question of whether or not gas-lift can efficiently deplete a given well or reservoir. This question cannot possibly be answered without first evaluating reservoir, surface and vertical-lift performance both as encountered today and as anticipated throughout the life of the well or wells. The technique presented in this paper was originally developed to upgrade gas-lift installation design from an applied art to an applied science. It has since been successfully used not only for this purpose, but also for the whole field of vertical-lift performance in its broadest sense. Lift efficiency should be considered important while the well is still flowing, as well as after natural flow ceases. Correct interpretation and proper modification of the vertical-lift performance of a producing well can provide dramatic improvement in production performance and/or efficiency. STATEMENT OF THEORY AND DEFINITIONS Fig. 1 illustrates the three divisions of production which will be used in this paper. The terms are a modified version of those presented in the very fine paper by Gilbert.&apos; The fields of reservoir and surface performance both have been greatly improved over the years. A study of those writings which may be found indicates that the field of vertical-lift performance has not progressed as well. There are two possible reasons for this lack of progress. 1. It has not been recognized as a scientific field in itself by the oil companies, as has reservoir engineering. 2. The equipment companies have confined their efforts to mechanical design research rather than the more basic study of vertical-lift performance of producing wells. Both organizations must have an economic stimulus for doing research in this field, and most of the results obtained in past work has been so erratic as to arouse little enthusiasm. The basic purpose of interpreting vertical-lift performance is to predict operating conditions below the surface of the ground from available data. The success of the interpretation depends upon the accuracy with

By William E. Ford, Edward Salisbury Dana

THIS Appendix contains a series of tables, more or leas complete, of minerals arranged according to chemical composition or to certain prominent crystallograhic or physical characters. These, it is believed, will be of service not only to the student, but ago to the skilled mineralogist. The type used in the printing of the mineral names indicates their relative importance. Table I is a complete list of the species named in this book arranged fist according to the prominent basic elements which they contain and secondly according to their acid radicals. Table II is of Minerals arranged according to their System of Crystallization The other tablets make no claim to completeness, being limited often to common ah important species. For an exhaustive system of Determinative Tables based particularly upon blowpipe and chemical characters, the student is referred to the work of Professors Brush and Pen- field, mentioned on p. 330.

Jan 1, 1922

By L. Adler

A relatively simple and effective technique is proposed to deal with the failure of geologic masses containing weakness planes. This technique, termed irextended" rupture envelope, provides a means to clearly distinguish rock and soil from fractured rock and, on a theoretical level, considers a matrix-inclusion system. It may also constitute the link between Mohr&apos;s and Griffith&apos;s failure theories. Included in the article are five sample problems concerning site location, structural design, strengthening the plane of weakness, changing the magnitudes of major and minor principal stresses and changing the orientations of major and minor principal stresses. Engineers trying to solve design problems in rock and soil mechanics have often assumed an iso-tropic and homogeneous medium. For naturally occurring geologic masses this assumption has always been viewed with regret. The following analysis which deals with the effects of plane anisotropy on failure presents a solution to this. The planes of weakness are joints, faults, bedding planes, fracture and cleavage (natural and induced), foliation and schistosity. The physical properties of these weakness planes include an undulating surface, frictional resistance, discontinuous extent, filling material, tightness and presence of water to cause a hydrostatic pore pressure. All of these properties relating to failure can be summarized in Mohr&apos;s rupture envelope for the plane of weakness. This, along with the geometrical orientation, strike and dip, of the plane of weakness produces what is termed an irextended" rupture envelope. MOHR&apos;S STRESS CIRCLE AND RUPTURE ENVELOPE The significant features of these concepts are listed below.&apos; 1) A point on the u - r coordinate plane represents the normal and tangential stress components on a reference area in the material. This area can have any orientation. (Fig. la)

Jan 1, 1963

By William Wraith

1. INTRODUCTION. AT the Washoe smelter,. Anaconda, Mont., the blister-copper from the converters is transferred, by means of a crane, to a refining-furnace,, in which it is brought to proper pitch by means of air and poles. From this furnace the refined copper, containing gold and silver, is poured into cast-iron molds placed on a platform-conveyor, giving an anode 36.75 in. long, 28 in. wide, and 21 in. thick. By reason of a disagreement between the smelter and the refinery, in reference to the silver-content of the anodes, it became necessary to investigate the methods of sampling used. II. SMELTER METHOD OF SAMPLING. At the smelter the sampling is done by " spotting " into water a small portion of the molten stream of copper as it flows from the furnace, by batting" the stream with a wooden paddle. The first sample is taken 30, min. after the pouring is started, three. other samples being taken at 1-hr. intervals, each sample weighing from 4 to 6 oz. The samples are dried, examined for particle&apos;s of burnt wood, screened on a 10-mesh screen of No. 8 wire to remove the fines, the oversize then screened on a 4-mesh screen of No. 20 wire to remove the coarse, the undersize of this screen being taken as the sample. Teh four portions thus obtained are thoroughly mixed and spli in half by passing over a 16-slot splitting-device, slots being 0.5 in. wide. One-half of the sample is sent to the laboratory for analysis and one-half kept as a duplicate. III. REFINERY METHOD OF SAMPLING. The method used at the refinery and also used in this investigation is the one developed by Dr. Edward Seller, of

Mar 1, 1910

INTRODUCTION This chapter summarizes characteristics of porphyry copper deposits within the Cordilleran orogen east of the Coast Range plutonic complex of the Yukon and British Columbia and south to the Columbia River plateau and the Idaho batholith. Porphyry copper deposits in this area reflect a geologic environment different from that found for mineralized intrusions elsewhere in the Cordilleran orogen, both to the south in the United States and Mexico and to the west in Alaska. A section on the Tertiary Cascade porphyry copper province is included herein. The Cascade province is considered separately because its deposits display a unique mineralogy and age of mineralization. That portion of the Cordilleran orogen described in this chapter is shown in Fig. 32, with the Cascades shown in Fig. 39 (see p. 114). The regional geology of this area has been described by Monger, et al. (1972), Hollister (1974), Wolfhard and Ney (1974), Field, et al. (1974), and Stacey (1974). Each offer slightly differing views on the post-Mississippian evolution of the geology in this porphyry copper province. The descriptive geology in this chapter has benefited from many discussions with J. E. Armstrong and J. W. H. Monger. Two separate petrologic models have been used popularly to categorize porphyry copper deposits in this area, a diorite and a quartz monzonite model. The diorite model, which involves a mineralized quartz-free pluton, has also been called the alkalic type (CZM Special Volume 15, 1976, and Soregaroli, 1975) and the syenite suite (Sutherland Brown, et al., 1971). The quartz monzonite model has also been named the calcalkalic type (CZM Special Volume 15, 1976) and includes mineralized quartz-bearing plutons compositionally ranging from quartz diorite to granite, with the igneous phase closest to ore in time and space commonly being quartz monzonite.

Jan 1, 1978

By Hugh H. Waesche

High quality quartz crystals weighing more than 50 grams are required in several important industrial applications.30,31 Primarily, they are the basic raw material for precision, electronic, frequency control components; this includes oscillators and filters in both radio and telephone services. Quartz crystals are also necessary for optical lenses and prisms in special applications requiring high ultraviolet light-transmission as in spectrographs. Quartz wedges are regular components for petrographic microscopes. The application of crystalline quartz as a transducer* in ultrasonic devices has increased in recent years despite strong competition from barium titanate and magnetostrictive [f] devices. Some quartz is fabricated into delay lines for radar. Man has valued quartz for fabrication of art objects since the dawn of history. The art forms were and are painstakingly carved and polished to form intricate figurines, bowls, statuettes, and the well-known crystal balls. The largest known ball, made of perfect quartz from Burma, is now in the National Museum in Washington. It is 12 7/8 in. in diameter and weighs 106 lb 12 oz. Clear, pure quartz chips and small crystals not meeting the electronic-grade dimensional requirements are known by the Brazilian term lasca. They are used to produce fused quartz having wide application in laboratory equipment, as special glasses, for torsion suspension in scientific instruments, and as a source material for growing large artificial quartz crystals 18,35 Electronic applications far exceed all other uses in importance so any discussion of high-quality quartz crystals must be concerned almost exclusively with those functions. Historical Background Because of their ubiquitous character and natural beauty, quartz crystals have long been of interest and known to man. They have been found among early Egyptian and Chinese art forms and the Sumerians are believed to have fashioned seals, beads, and other jewelry from quartz crystals, perhaps 5,000 years ago. Also, American Indians made arrow heads and fashioned some simple objects of different kinds. The origin of the name quartz, although of Greek derivation, is uncertain. The Greeks appropriately applied their word for frozen water or ice, krustallos, to quartz. The present-day, large-scale practical applications of quartz crystals began in 1880-1881 when Pierre and Jacques Curie reported discovery of the "piezoelectric" effect. They found this effect first in Rochelle salt, a common product of grape-wine refineries, while studying crystal symmetry. Piezoelectricity is that property found in certain crystals, including quartz, whereby electrical charges of equal and opposite sign appear on opposite parts of the crystals when they are stressed. If equal and opposite forces are applied to two opposing prism edges of a single untwinned quartz crystal a positive electrical charge will appear on one edge and a negative charge on the other. The amount of the charges will be directly proportional to the force applied. This property seems to be intimately related to pyroelectricity

Jan 1, 1960

The beginning of Colorado&apos;s mining industry is linked on one side with that of the Appalachian districts and on the other side with that of California, because the first discoveries were made by pioneers when on their way from Georgia to California. In the summer of 1849 a party of seven Georgians were taking a herd of thoroughbred horses across the continent to the Pacific coast. They reached Camp Lyon, on the Arkansas river, in October, and, meeting James Dempsey, a Government guide, they were persuaded by him that it was too late to cross the mountains that season. His advice was accepted, and, moving northward, they established a winter camp at the junction of Cherry creek with the Platte, close to the site of the city of Denver. Upon a sand-bar, lining the south side of the river, they built two cabins. During the closing months of 1849 they prospected the alluvial banks of Cherry creek, but they made no attempt to penetrate into the mountain canyons, near them, westward, for fear of the Indians.* They found gold in several places along Cherry creek, and particularly at a spot 16 miles up the stream from their camp. From the feathers of the wild geese that they shot they obtained quills in which they placed their gold-dust. This party of Georgians consisted of Dr. L. J. Russell and his brother, Green Russell, also A. T. Lloyd, G. W. Kiker, and P. H. Clark. Early in 1850 they crossed the main range of the Rocky Mountains by the Bridger pass and went on to California. They mined near Downieville, and were successful. Occasionally mention was made by them of the gold

Jan 1, 1932

By L. B. Schmitt, N. H. Polakowski

Square bars of cold-dvawn copper, mild steel and a 2024 aluminum alloy were forced through an adjulstable gap between two hardened steel rollers by pulling or pushing. The rollers were either free to rotate or were locked in position so that conditions comparable with drawing, rolling, ad containerless extrusion could be created at will. Push or pull forces as well as roll separatirg forces were measured. Forming efficiency and coefficients of friction were determined. For- slow-rate deformation the values ot µ wrere between 0.09 and 0.14. Possibilities for further investigation are indicated. THIS work was undertaken with the aim of a) determining the principal parameters of cold drawing under simplified conditions directly, without recourse to speculative assumptions and b) comparing drawing with rolling and extrusion from the viewpoint of forces involved and deformation efficiency. Data of type a) relating forces in axially-symmet-rical drawing to die geometry. drafting schedules, material properties and lubrication conditions are abundant. Their intrinsic value is. however. limited as long as the radial die forces are unknown. On the other hand. the difficulties associated with measurement of these forces are serious as witnessed by the extreme paucity of such information."" Comparative investigations of type b) were also remarkably few and they all employed ring-shaped dies through which round bars were either drawn or pushed.2-4 Only in one case were the applied and the die splitting forces measured simultaneously.2 In order to simplify the problem, deformation under approximately biaxial conditions was adopted in the present work;. This enables both the drawing (rolling, extruding) efforts and the separating forces to be measured with reasonable ease by conventional methods. Since drawing, extrusion, and rolling can be carried out under virtually identical conditions only in a roller die. an adjustable tool of this type was constructed. The circular die profile involved a difficulty with interpreting the drawing and extrusion data. This was obviated by arbitrarily defining the angle between a contact chord and the drawing plane as the -.equivalent" die semiangle. The simplification was considered permissible since the effect of die angle was not specifically investigated. An additional conlplication was caused by the square cross section of the processed bars. This shape was selected as a compromise between the desire to have as massive as possible specimens and the capacity of the roller die. The metal was only partially restrained from spreading laterally. the flow conditions being therefore intermediate between plane stress and plane strain. On the Huber-Mises yield criterion the constrained and uni-axial yield strengths differ by up to 16 pct but the actual error due to the ignorance of the constraint factor was presumably much smaller than the maximum. In spite of these reservations it was felt that the method employed and results obtained have some merit. With certain further refinements to be indicated later, this technique can yield data perhaps more useful for checking metal forming theories than other, mostly indirect, methods. EXPERIMENTAL Materials—The metals used together with their principal mechanical properties are listed in Table I.

Jan 1, 1961