Search Documents

By W. L. Martin, J. N. Dew, H. B. Steves, M. L. Powers

This paper presents and discusses the results obtained during a pilot test in the Loco field in southern Okla homa. The test was conducted in a 2%-acre pattern that was part of a 20-acre conventional waterflood pilot area. The conventional flood was well past its economic limit when the hot waterflood was initiated to obtain technical information and operating experience. Temperature data from nine observation wells showed that about 75 percent of the pattern was affected by heat, and that heat losses were severe in the pilot pattern. About 60 percent of the injected heat was lost to overburden and underburden zones during hot-water injection. Wellbore heat losses were held at tolerable levels at the shallow depth of the test by providing a low-pressure air annulus between the injection tubing and well casing. Hot water provided water injectivity increases of 200 to 400 percent. The hot water channeled across the lower portion of the oil sand in three directions through zones of relatively high water saturation. There was no conclusive evidence that natural fractures or pressure partings aflected the flow of fluids in the pilot pattern; however response undoubtedly was aflected by localized pressure gradients and by injection-production rate ratios. The results showed that hot waterflooding increased oil recovery in a reservoir containing 600 cp oil. The total tertiary oil production from the pilot pattern area was 3,896 bbl or about 156 bbl/acre-ft swept by heat. The corre.sponding WOR was about 34:I. Description of the Hot Waterflood Process To hot waterflood an oil reservoir, water is injected that has been heated to a temperature substantially higher than the original reservoir temperature, but lower than the vaporization temperature of water at the prevailing pressures. In the reservoir the hot water flows continuously into cooler sand and rapidly loses heat to the sand until it has been cooled to the original reservoir temperature. Thus, a heated zone and a region or "bank" of cooled water begins to accumulate immediately after hot water injection is started. This bank of cooled water continues to grow ahead of the heated zone, which also grows, but at a slower rate. This occurs because heat transfer is almost instantaneous, and the ratio of heat capacities of water to rock is such that two or three unit PV of hot water must be injected to heat a given unit bulk volume of the reservoir. The primary displacement mechanism is the same for both hot and conventional cold waterfloods; i.e., "piston" displacement occurs at the original reservoir temperature. The incremental benefits of hot waterflooding usually occur long after the breakthrough of cold water at producing wells, and the increased oil recovery necessarily is accomplished with high WOR's (water-oil ratios). Heat decreases the viscosity and density of oil and water. These effects result in more rapid and increased recovery of secondary or tertiary oil. If the cost of the required heat is low enough, the ultimate oil recovery of a hot waterflood should be increased substantially over what would be expected at the economic limit of a conventional cold waterflood. The economic benefits of any hot-fluid injection project depend primarily upon the cost of the heat required to produce more oil at an increased rate. This cost depends in part upon the amount of heat lost to surrounding formations. Heat loss depends upon reservoir thickness, water injection rate and temperature, the depth of the formation, well spacing, and the characteristics of the reservoir rock and surrounding formations. In general, percentage heat losses decrease as injection rate and reservoir thickness increase. Although it is an old idea, hot-water injection has not received widespread field application in the oil industry as a drive process. Much of the original field work with hot water was done in Pennsylvania fields where water permeabilities and injection rates are low. In these cases, hot-water injection was used primarily as a means of increasing in-jectivities — not as a recovery process. Ramey' recently has published an excellent review of the development of hot fluid injection processes. Recent publications"' and our own experiences now indicate that hot water or steam injection also can effectively increase the oil recovery from reservoirs containing viscous crudes. However, the economics of these methods as displacement processes have not been established. Several theoretical predictive techniques have been published (for a review see Ramey'), but simplifying assumptions make

Jan 1, 1969

By Klaus Schwerdtfeger

The rate of formation of silicon monoxide from silica spheres has been measured at 1500°C in H2, H2-H2O, H2-He, H2-Ar, and CO-CO2 gas mixtures. Indications are that in the hydrogen-containing gases the reaction rate is mainly determined by convective diffz~sion. In the CO-CO2 mixtures the rate approches a constant value which is independent of sphere diometer (and gas velocity). This suggests that a surface reaction becomes rate controlling in CO-CO2 gas. WHENEVER silica is exposed at elevated temperature to a strongly reducing atmosphere there occurs, inevitably, a volatilization of silica by the formation of gaseous silicon monoxide. Because of the importance of this reaction in metallurgical processes and laboratory experiments, its kinetics were studied in the present work. EXPERIMENTAL The spheres made of vitreous silica were suspended by a molybdenum wire in the hot zone of a gas-tight high-purity recrystallized alumina furnace tube of 3.1 cm internal diam and 100 cm length. Molybdenum wire resistance heating was used. A purified H2, H2-H2O, H2-He, H2-Ar, or CO-CO2 gas mixture was passed through the tube, from top to bottom. The amount of silicon monoxide formed was determined by weighing the silica balls before and after the experiments. The silica balls were made from commercially available translucent fused quartz glass. In experiments with hydrogen-containing gases the silica stayed vitreous during the experiment, whereas in experiments with CO-CO2 mixtures, which were performed over longer times, the balls were always crystallized to cristobalite (as determined by X-ray examination) at the surface. Constant-pressure head capillary flowmeters were used to control the composition of H2-He, H2-Ar, and CO-CO2 gas mixtures. The oxygen and water vapor were removed from the gases containing hydrogen by passage through columns containing platinized asbestos (450°C) and an-hydrone. The CO was purified from O2 and CO2 by passing it through activated copper (200°C) and through ascarite. The H2-H2O gas mixtures were prepared by passing purified Hz through a mixture of oxalic acid dihydrate and anhydrous oxalic acid held at a constant temperature in a water bath. The equilibrium water vapor pressures of oxalic acid dihydrate-anhydrous oxalic acid mixtures were taken from the available data.1 The furnace system was checked for sufficient gas tightness at regular intervals. As an additional check, the H2O and CO2 contents were measured in the exit gas and were found to agree closely with the metered contents when H2-H2O or CO-CO2 mixtures were used. When purified H2 was used, H2O pressures found in the exit gas were always below 0.1 mm Hg. These contents originate either from an incomplete reoxidation of silicon monoxide in the cold part of the furnace or from small leaks which cannot be avoided. If the latter is the case, such small uncontrolled H2O contents decrease the partial pressure of SiO in equilibrium with SiO2 by less than about 7 pct, which is considered small in comparison to other experimental uncertainties. The temperature of the furnace was controlled automatically in the usual manner. The reported temperature was measured with a Pl-Pt/l0pct Rh thermocouple and was accurate to ± 5°C. TRANSPORT-CONTROL LED RATE OF REDUCTION The gaseous convective diffusion from the surface of a sphere can be predicted from the semiempirical relationship obtained by Ranz and Marshall2 in a study of the evaporation of water and benzene drops in air. The following equation applies:

Jan 1, 1967

By T. L. Joseph

It is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man's thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life's work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe's pioneer work in the field of metallurgy.. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that underlies the production of steel. Although Dr. Howe's work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book' on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe's ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of- much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blastfurnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1947

By T. L. Joseph

It is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man's thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life's work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe's pioneer work in the field of metallurgy.. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that underlies the production of steel. Although Dr. Howe's work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book' on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe's ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of- much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blastfurnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1947

By Jack L. Taylor

Single crystals of tungsten grown from powder -metallurgy swaged rod by high-temperative annealing were deformed in tetzsion at temperatures from 2500 to 5000 OF. Orientation of specittzen tensile axis, strained ratrix, and defortnation bands was determined optically by reflections from {110} etch pits. Slip traces meve analyzed and slip directiorz determined. Results indicate that {110}(111) , {112){111}. and {123}{111} type slip occur in tungsten over the terpe,atuve rutge investigated. Slip is orientation-dependent occuvring on tCuzt cowzbitzation oj slip plane and direction which has the highest critical resolved shear stvess. Overshooting appears to be a general occurrence between 2500' and 5000°F. Dejornatiotz bands show rotation in a directiorz opposite to the yotation of tire tensile axis. DEFORMATION in bcc metals has been reviewed by Maddin and Chen,' Keh and eissman,' and most recently by Nabarro, Basinski, and olt. From these reviews it is apparent that some disagreement exists concerning the crystallography of plastic deformation in bcc metals. There is evidence of noncrystallo-graphic slip, the crystal slipping on or near a noncrys-tallographic plane in the (111) zone for which the resolved shear stress is greatest. There is also evidence to indicate that crystallographic slip occurs in the planes of the same zone. On the other hand, there is agreement that the close-packed direction ( 111) is the slip direction in bcc metals. Further, in pure bcc metals4 and alloys the operative crystallographic slip systems are strongly dependent on temperature. Both crystallographic and noncrystallographic slip have been reportede8 in tungsten, a group VIA bcc metal. The number of slip families which operate in the case of crystallographic slip, however, has been in question. The earliest study by oucher' of single-crystal tungsten tested at temperatures of 1800 to 5000°F led to the conclusion that only {112)( 111) type slip operated. Raymond and eumann recently reached the same conclusion studying deformation by rolling of plasma-flame single crystals at 1800°F; however, only [loo] and [110] orientations were studied. Work at high temperatures by Leber and Pughs on tungsten and Chen and Maddin9 on molybdenum suggests that conjugate slip on nonparallel (110) planes may account for the slip on (112) and (123) planes found by others working with bcc metals. The present paper presents evidence of three families or modes of slip in tungsten in the temperature EXPERIMENTAL PROCEDURE Material. Standard microtensile specimens, 0.160 in. diam by 0.640 in. gage length, were ground from commercial powder-metallurgy swaged tungsten rod, type MK. Specimens were heated for 10 min at 5150°F or 6 hr at 5400°F in vacuum of 1 x 105 Torr or less to produce single crystals. At the lower temperature an average of two out of seven specimens heated in a group developed single crystals throughout the specimen length as shown in Fig. 1, the rest remaining wholly poly crystalline. At the higher temperature, three or four out of seven specimens became single crystal. Other than to note that Laue X-ray photographs generally showed sharp, well-defined spots, no attempt was made to assess crystal perfection or measure dislocation density. Two tungsten single crystals grown from the melt by the plasma-arc process were also used for this study.

Jan 1, 1967

By Irwin Roman

PART I. INTRODUCTION THE literature of geophysics as applied to the discovery of mineral deposits has been very extensive during the past few years, but there seem to be few references to the use of the method of least squares for obtaining better interpretations of the observed data .2 There seems to be a general reluctance among geologists and. engineers to acquire the technique of least squares, in spite of the fact that a thorough knowledge of the theory is not necessary for the use of the method.

Jan 1, 1931

By W. M. McCardell, W. O. Winsauer, M. Williams

The mechanism by which an electrical potential difference is developed between two salt solutions separated by shale is shown to be a consequence of the electrical double layer of the shale surfaces. A mathematical derivation is presented to show -the dependence of the potential on the shale characteristic.? and on the concentration of the salt solutions. The equations developed describe adequately the potential-concentration behavior of a long shale core. The equations also describe the variation of potential of sand-shale mixtures with variation of clay content. Ion adsorption i* an important factor in he developments of the surface charge on the shale. and electrical resistivity and ion transference number data are emlployed to estimate the increase of surface charge with concentration. Since the potential is shown to be dependent on the characteristics of the particular .system. water salinities estimated from the potential log by previously proposed methods may be low in some rase;. INTRODUCTION That the electric well log exists today may he attributed to the ingenuity of the Schlumberger brothers who adapted to the logging of wells techniques which were originally developed as surface prospecting methods for the location of ore bodies Empirically it was found that the potential curve of the electric log usually gave values for clean sands which were negative with respect to the values for shales. It was suggested that the potential was responsive to porosity. It was postulated in explanation? that the potential was the sum of a streaming potential, which differed for sands and shales, and of an "electro-chemical" potential of undetermined origin. Mounce and Rust in 1943 showed that the streaming potential is small in most cases and that the potential is generated by a process in which shale and a salinity difference play-essential party. Dickey.:' in the same year, concluded that the potential is dependent upon adsorptive properties of reservoir rock. Wyllie in 1949. and Wyllie and Patnode, in 1950, measured the potential-: between two salt solutions separated by barriers of either naturally-compacted or artificially-compacted shales and concluded that the potential can be expressed by where E is the potential R is the gas content F is Faraday's constant T is the absolute temperature are the activities of the two uni-univalent solutions These authors postulated that shale. in the ideal case is impermeable to the migration of negative ions. Any potential less than the "ideal" shale potential was considered to be due to imperfections in the shale barrier. Although the studies by Wyllie and Patnode of the development of the shale potential are fairly recent. investigators in fields other than well logging have discussed the mechanisms responsible for analogous potentials over a period of several decades. Although it is evident that much thought has been devoted to the question of the origin of the potential observed in wells, it is also apparent that all of the explanations presented to

Jan 1, 1953

By K. A. Slagle

Hydraulic analysis of the wellbore has become increasingly inzportant for designing cementing operations and selecting equipment, materials and techniques to complenzent modern well-c-ompletion practices. Non-Newtonian fluid technology has advanced beyond the point where former empirical methods of analysis adequately define the hydraulic system and fluid properties. In view of these factors, this paper describes a series of rheological calculations which have been found practical, through field usage, for assistance in selecting a cementing program. A relatively simple laboratory method using standard viscometric equipment is suggested for determination of the rheological properties of slurries, and clrrta are presented on some of the more common cementitrg conzposition.A. A criterion for divergence from laminar-flow characteristics has been proposed. Usefulness of the calculations is indicated by examples of cementing operations where they have been used. INTRODUCTION With the changing aspects of well-completion practices during the past few years, it has been increasingly important to have a relatively simple method of analyzing the flow conditions existing in the well during cementing operations. This is particularly true in view of the improved economics toward which most of the changes have been directed. Rheological characteristics of slurries used for cementing should be a major consideration in the trend toward smaller casing sizes, either single or multiple strings. Receiving increased attention is the practice advocated in 1948 by Howard and Clark' of attaining turbulent flow with the fluids circulated during a primary cementing operation. While there may still be a difference of opinion concerning this technique, most available information indicates that superior primary-cementing results are generally obtained when high displacement rates are employed. Fluid properties of the slurry to be used must be available, as well as calculation methods, to determine what flow rates should be attained and the probable consequences in terms of frictional pressure and horsepower utilization. It would certainly be inappropriate to attempt high displacement velocities if sufficient pressure might be developed to create lost circulation. Since cementing slurries are non-Newtonian fluids, it is not possible to define their rheological or fluid properties by the single factor of viscosity and then make calculations for the quantities just described. Because the shear stress-shear rate ratio is not constant: it becomes necessary to establish at least two parameters for adequate fluid-flow calculations. It is not the purpose of this paper to delve into the mathematical development of non-Newtonian technology, nor to discuss the arbitrary classification system under which a single fluid may resemble two or three different classes depending upon experimental conditions. Rather, the intention is to present a useful series of calculations based on a concept applicable to both Newtonian fluids and to the preponderance of non-Newtonian fluids encountered in the oil-producing industry. Development of this approach was begun some 32 years ago,' and has most recently been brought to fruition by Metzner and his co-workers at the U. of Deleware. Some non-Newtonian fluids encountered in the petroleum industry, other than cementing slurries, have also had the benefit of this method of analysis."' The two parameters required to define the fluid are usually denoted by the symbols n' and K' and, for the purposes of this discussion, are called "flow behavior index" and "consistency index", respectively. These two slurry properties permit calculation of the Reynolds' number and the "critical" velocity, or the velocity at which departure from laminar flow begins. EXPERIMENTAL DETERMINATIONS The two principal instruments used for rheological studies are the pipeline (capillary-tube) viscometer and the rotational viscometer. When conveniently possible, a capillary-tube viscometer (where the pressure drop and flow rate of the material can be measured) is the better method for rigorous determination of the flow behavior index and consistency index for non-Newtonian fluids. With pressure-drop data at various flow rates, it is then possible to prepare a logarithmic plot of shear rate as the abscissa-shear stress as the ordinate. For fluids which do not exhibit time-dependency, these data will usually produce a straight line. The flow behavior index n' represents the slope of this line, while the consistency index K' becomes the intercept of this line at unity shear rate in accordance with the mathematical derivations associated with this concept of rheology. Due to the difficulties anticipated in maintaining a uniform, pumpable cement slurry for the time interval required to obtain measurements from the pipe viscometer, the n' and K' data reported herein were obtained using a direct-indicating rotational viscometer (Fig. 2). The

By Bruce Chalmers, D. C. Larson

Aluminum crystals with longitudinal-axis orientations of (111) . (110), and (100) were deforined in tension and annealed. The conditions of deformation were controlled so that the re crystallization nuclei originated in either the heavily deformed regions at saw cuts {artificial nucleation) or in the lightly deformed matrix (spontaneous nucleation). The artificial-nucleatioln experiments showed that in lightly deformed (110) and (100) crystals low-angle twist boundaries are most mobile, while in (111> crystals and heavily deformed (110) and (100) crystals high-angle tilt boundaries with near (111) rotations are favored. The spontaneous-nucleation experiments showed the existence of preferred orientations in the (111) crystals. The nonrandomness of the grain orientations is quantitatively determined through a comparison with the results which would he obtained from a randowl set of grain ovientations. PREVIOUS recrystallization studies have been performed on single crystals deformed in tension.1 7 The crystals used in these studies usually had random tensile-axis orientations and the extent of deformation was not a primary consideration. The present study concerns the recrystallization of single crystals with tensile-axis orientations of (Ill), (110), and (100). The emphasis of this work is on the influence of the tensile-axis orientation and the degree of deformation on both the nucleation and growth processes. The multiple-slip orientations were chosen because secondary slip or slip intersection promotes nucleation.1,5,8 These crystals recrystallize at lower strains than the crystals which are oriented for single slip. Also, the greatest variation in deformation behavior is exhibited by the multiple-slip orientations. The stress-strain curves for crystals with tensile-axis orientations of (111) are higher than the stress-strain curves for poly-crystals, and the stress-strain curves for crystals with tensile-axis orientations of (100) are lower (at large strains) than the stress-strain curves for the crystals which deform initially in single slip.g The recrystallization nuclei originated in either 1) the homogeneously* deformed matrix of the crys- tals or 2) the heavily and inhomogeneously deformed regions at saw cuts. The nuclei will be referred to hereafter as spontaneous and artificial nuclei, respectively. The two terms do not imply a difference in the nature of the nuclei; they imply simply a difference in the mode of introduction of the nuclei. During spontaneous nucleation very few (always less than ten) grains nucleate, while during artificial nucleation large numbers of grains nucleate. Only a fraction of the artificially nucleated grains penetrate very far into the deformed matrix during annealing. The grains that penetrate the farthest into the deformed matrix will be referred to as the dominant grains. EXPERIMENTAL PROCEDURE The thirty-five crystals used in this investigation were grown from the melt in milled graphite boats at a rate of 1.6 cm per hr. The crystals had dimensions of approximately 6 by 12 by 80 or 6 by 6 by 80 mm and the aluminum was of 99.992 pet purity. The as-grown crystals were annealed at 610°C for 24 hr and furnace-cooled. They were then heavily etched and electropolished in a solution of five parts methanol to one part perchloric acid. The crystal orientations were obtained by back-reflection Laue photographs and were accurate to ±2 deg. The tensile-axis orientations were (loo), (110), and (111). Two of the side faces of the (111) crystals were (110) lanes. The (110) crystals had both {100) and {110) side faces and the (100) crystals had (100) side faces. The crystals were deformed at a strain rate of 0.003 per min. Shear stress and shear strain were obtained by multiplying and dividing the tensile stress and strain, respectively, by the Schmid factor, m. For the (111) crystals m = 0.272 and for the (110) and the (100) crystals m = 0.408. The Schmid factor is effectively constant during deformation for all orientations. The deformed crystals were sawed into 1-in.-long specimens while the crystals were totally enclosed in a graphite boat. The sawing was performed very carefully in order to limit the plastic deformation to the sawed regions. The specimens were electropolished in the solution mentioned above to remove the sawed-end deformation as well as controlled amounts of surface material. A special stainless-steel grip was used to hold the specimens during the electropolishing treatment. The gripping faces were flat, with no teeth, to prevent the introduction of extraneous de-

Jan 1, 1964

By Albert E. Ketler

Introduction – The introduction of computerized monitoring and control (M/c) equipment into the U.S. coal mining industry may prove to be of truly revolutionary proportions in the 801s.Many of you are aware that the British have developed and have been using such sophisticated M/C equipment for performing production and safety related tasks in their coal mines for nearly a decade. The benefits of M/C systems in the mining industry are usually separated into those which improve productivity, and hence make money for the company, and those which improve safety, and hence cost money. The economic benefits of M/C are startling for the production related functions such as for monitoring and controlling conveyor belts, de-watering pumps, electrical power distribution, and the like. It doesn't take much analysis to show that hundreds and even thousands of tons of coal don't get mined every time a belt shuts down or when power is out due to circuit breakers tripping for any number of reasons. A flood, caused by a malfunctioning pump which goes undetected for lack of feedback monitoring of pumping parameters, can destroy literally millions of dollars worth of mining equipment. The M/C system would be justified or not based on whether or not the productivity benefits balanced the cost within a timespan commensurate with the return on capital philosophy of the company. The safety related benefits are easily underestimated or ignored completely and the purpose of this paper is to under-score some of these benefits, as well as to review the application of M/C to the coal mining industry. The companies involved are Transmitton Ltd of England and Minetics Corp of Pittsburgh, Pennsylvania. Transmitton is probably the most experienced manufacturer of M/C equipment in the world having some 200 installations to its credit. Minetics is the marketing and manufacturing arm for Transmitton in the U.S.A. and is responsible for all aspects of distribution and service. Plans are underway for manufacturing of the Transmitton hardware for U.S. sales to be transplanted into U.S. subcontractors by 1981. Thus our coal mining industry will benefit from British technology, but without the delays and additional costs usually involved in international shipments.

Jan 1, 1981

By E. W. Davis

THE mysterious Lake Erie price for iron ore, established each spring, determines the maximum price that will be paid during the following season for ore of Mesabi Non-Bessemer base grade. This price is impor-tant to the ore producers, but since most of the ore in the Lake Superior district is owned or controlled by consuming inter-ests, the really important question to them is not the price of ore but how much it will cost them to mine and transport their season's requirements to their furnace plants. However, a few million tons are actually sold each year, and considerable quantities are traded for mixing purposes, and the negotiations for these sales and trades usually begin with some reference to the Lake Erie price. There is no difficulty with the Lake Erie price itself or with the manner in which it is established, but the system prescribed for determining the values of ores that are not exactly base grade is incomplete. The Lake Erie price takes into consideration only the iron and phosphorus contained in the ore, but when the ore producer is negotiating a sale or trade, he is confronted by the fact that his ore must be studied and the price adjusted, not only on the basis of the iron and phosphorus analyses, as specified by the Lake Erie price, but also on the basis of silica, alumina, man-ganese, structure, etc. The vague and unsatisfactory methods used in making these adjustments bear some relation to the manner in which the ore is supposed to act in the blast furnace. The ore producer may not understand all of the idiosyncrasies of the blast furnace, but if the smelting-plant operators have a system more accu-rate than the Lake Erie price method for determining the relative values of different ores, why not pass this information on to the ore producers, so that they can make use of it and perhaps modify their practice in such a manner as to benefit both them-selves and their customers? There is a lack of understanding and appreciation between these two groups that may, to some extent, be unavoidable, but in the interests of efficiency and conservation rules that are more accurate and complete than the Lake Erie price method in use at the present time should be established for the guidance of the ore producers.

Jan 1, 1940

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world's mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of. stock control. The percentages given rep-resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geologi-cal Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals. Coal, although it is one of the most important minerals, was omitted because , not more than one or two per cent of the world's production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By P. G. Chamberlain, E. R. Podnieks, R. E. Thill

Although published data on the physical properties of rock are voluminous, information is often lacking on the environmental conditions under which such data were acquired. Efforts are frequently directed to improve specimen tolerances and preparation procedures; but investigators often overlook giving the rock environment equally careful control during the testing program. Generally, tests are conducted at existing laboratory room conditions, and the prepared rock specimens are frequently, if not most commonly, air-dried for various lengths of time before testing. The standard testing atmosphere recommended by the American Society for Testing & Materials (ASTM)1 is 73.4°F and 50% relative humidity. To maintain a rock at 50% relative humidity for testing purposes, however, requires special equipment and preconditioning procedures, as this study demonstrates. Relatively small variations in the moisture content of a specimen, for example, due to the coolants or lubricants used during specimen preparation, can cause significant variations in the physical properties measured. Such moisture variations may occur in the rock specimen even after it is air-dried, since laboratory humidity conditions commonly fluctuate from day to day. For these reasons, this study emphasizes procedures for preconditioning and maintaining a controlled environment during testing. Although the effects of moisture or temperature on rock properties have previously been studied, their combined effect on rock properties is unknown. In this study, uniaxial compressive strength, Young's and stiffness moduli, and longitudinal wave velocity were determined and compared under controlled conditions of temperature, moisture, and pressure for 11 environments considered to be of particular interest in laboratory, in-situ, and even simulated lunar environments. The following environments were selected for this program: -250°F under dry, 50%

Jan 1, 1972

By R. L. Dalton, L. A. Rapoport, C. W. Carpenter

Procedures have been developed to study the performance characteristics of unconfined pilot water floods using scaled laboratory models. The effects of operating conditions on pilot performance for variozrs well patterns have been investigated. The limitations of the laboratory model studies are outlined. Relationships between the oil recoveries of pilots and large-scale floods have been established. The applications of model studies to the prediction of large-scale waterflood performance and pilot flood design are discussed. INTRODUCTION Pilot water floods are undertaken to evaluate operational procedures and to gain advance information about the performance of an extensive water flood. In general, however, the performance of a pilot flood is not directly indicative of what can be expected from a large-scale pattern water flood. This difference stems from the fact that the over-all flow configurations are not the same for the two systems. A water flood normally consists of an array of identical well patterns. In such an array, the perimeters of the well patterns are axes of symmetry and act as impermeable boundaries. Thus, an extensive, pattern water flood can be visualized as a repetition of "confined" floods. In contrast, a pilot water flood involving only one or a few well patterns is "unconfined". Here the well patterns are not balanced by other flood units; hence, the perimeter of the pilot area does not act as an effective boundary. Accordingly, only a portion of the fluids injected (and also of those originally contained within the pilot area) is captured by the producers of the pilot. The rest escapes into the surrounding reservoir. This usually causes the amounts of oil and water produced in the pilot to be different from those recovered by a producer in an extensive water flood. Moreover, the recovery observed in the pilot can be expected to be greatly influenced by operating conditions, i.e., by the bottom-hole pressures at the injection and producing wells. The above considerations show that full utilization of pilot test results and reliable prediction of large- scale water floods require a knowledge of the relationship between the recovery performance of confined and unconfined well patterns. To date, only limited basic information is available on the behavior of pilot water floods. Craig, et al,' have investigated the effects of initial gas saturation, oil-to-water mobility ratio, and well damage on the oil recovered from a single, "normal" five-spot pilot pattern (Fig. 1). Rosenbaum and Matthews2 studied the effect of initial gas saturation and mobility ratio on the ratio of production rate to injection rate for various groupings of five-spot patterns. Paulse113 investigated the effect of mobility ratio and distance from the pilot to the edge of the reservoir on the areal sweep in a single "inverted" five-spot (Fig. 1). However, none of these studies considered the effect of operating conditions on pilot flood behavior. Moreover, hardly any of the work to date dealt explicitly with the oil-recovery performance of the pilot floods. The purpose of this paper is to introduce the concept of interrelation between pilot flood behavior and operating conditions, to illustrate this interrelation by means of experimental data and to compare the recovery performances of dif-

By A. W. Gray

Page CRUSHING STRENGTH...................... 659 The Black Dynamometer....................659 A Standardized Procedure for Crushing Strength Tests...... 660 Influence of Height of Test-piece upon Apparent Strength ..... 662 Influence of Packing Pressure and of Packing Time........ 662 Application of the Logarithmic Law...............665 Influence of Amalgamation Variables.............. 665 Influence of Temperature................... 669 The Transition Region Near 70" C............... 671 Influence of Packing Pressure at Various Temperatures ...... 673 Influence of Age upon Alloy and Amalgam........... 676 DIMENSIONAL CHANGES DURING THE HARDENING OF AN AMALGAM .......................... 678 The Black Amalgam Micrometer............... 678 Thermostated Dilatometer Designed by the Author........ 681 Graphical Representation of Reaction Expansions......... 683 The Typical Reaction Expansion Curve ............. 684 Influence of Packing Pressure................. 686 Influence of Trituration Time................. 687 Influence of Temperature................... 688 Influence of Mercury-alloy Ratio................ 689 Influence of Packing Time................... 689 Influence of Annealing the Alloy................ 691 Influence of Size of Alloy Particles...............691 Extension of the Typical Expansion Curve........... 693 Influence of Thermal Softening and of Reamalgamating a Hardened Amalgam.......................... 634 Curves Obtained with a Variety of Dental Alloys ........ 694 Copper Amalgam ...................... 694 PRACTICAL APPLICATIONS OF THE RESULTS.......... 695 Phenomena which reveal chemical and physical processes that probably go on in many alloys at temperatures not far removed from their melting ranges are observable in dental amalgams. These amalgams should. therefore. be of even more interest to the metallographer, the metallurgistl the chemist. and the physicist than to the dentist who uses them for saving decaying teeth. For this reason I am here de-

Jan 1, 1919

By William R. Barton

Iron and steel slag represent man's most successful attempt to date to profitably utilize a solid waste. Its consumption represents a solution to a solid waste problem and also represents tonnage of natural aggregates that will not have to be mined with concomitant disturbance of the land. Slag has been produced as long as iron has been made; but until a little more than 50 years ago, it was mostly a waste product to be disposed of with as little effort and cost as possible. Huge piles of waste slag were generated over the years of iron and steelmaking. Sporadic use was found for small amounts starting with slag (from Catalan forges) used for road bases by the Roman Empire. The first recorded sustained commercial use was, as is often the case in man's history, for making war. Some profit- conscious munitions maker in the 16th century realized that he could make cannon balls of slag instead of the more precious iron. Other small-volume uses gradually developed: cast building blocks, slag-lime mortars and cements, slag wool, ballast, road base, and, finally, in concrete. But it was not until after World War II that the true potential of blast-furnace slag as a construction aggregate was really recognized. Now nearly all blast-furnace slag produced is used, and much of the earlier stock- piles in the U. S. have been reduced or entirely consumed. Steel slag for aggregate use has been in commerce for only the past 10 years, and use has increased rapidly (10-50% per year) during the past 5 years as blast-furnace slag supplies became depleted. However, much remains to be accomplished in determining character and optimum conditions of use for various types of steel slags before such slags will realize their full use potential. Although slag represents only 2% of construction aggregate materials used in the U.S., its production involves certain features that make its production record far more important than national tonnage figures would indicate. Its source is in iron and steel production and concomitantly slag availability is restricted to those areas where iron or steel is produced. In such areas, it often represents one of the principal aggregates marketed and, because of special properties that make slag a selected aggregate for certain uses, the tonnage imbalance may be overcome by the importance of its contribution to quality or special characteristics of end products. The location and number (Fig. 1) of slag plants handling this annual production is governed by the geographic makeup of the iron producing industry. Prior to the period marked by World War 11, most blast furnaces were in the Great Lakes area-Pittsburgh, Cleveland, Chicago, Gary, Buffalo, Detroit, Youngstown, and Toledo, with exceptions at Baltimore, Bethlehem, and Birmingham. Since that time, iron and steel facilities have been established in Texas, Utah, and California. Today 85 slag plants in 15 states provide employment for almost 2000 persons. The slag plants also recover almost 4 million tons of slag-encrusted iron each year for return to the blast furnaces. Much of the success in developing uses for slag can be attributed to the efforts of the National Slag Association founded in 1918. Since then, it has conducted numerous field and laboratory investigations to demonstrate the properties and uses for slag and slag products. These investigations have resulted in total recognition of blast-furnace slag as a construction material of consequence. The American Society for Testing & Materials Designation C125 recognizes blast-furnace slag as "the nonmetallic product consisting essentially of silicates and aluminosilicates of

Jan 1, 1975

By Donald Jaffe, Michael B. Bever

The solidification of Al-Zn alloys (2 to 70 pct Zn was investigated at different rates of solidification. The resulting structures were studied; the amounts of nonequilibrium eutectic were measured and compared with the amounts calculated on the assumption of no diffusion in the solid. The compositions of the cored primary constituent were investigated by quantitative autoradiography after activation of the zinc by neutron irradiation. These compositions were also determined from microhardness values. IN a recent investigation of the soltdification of aluminum-rich AI-Cu alloys,' the amounts of non-equilibrium eutectic were measured and compared with the amounts calculated on the assumption of no diffusion in the solid. The compositions of the cored primary constituent were investigated by quantitative autoradiography. The work reported here extends the investigation of nonequilibrium solidification to the Al-Zn system in the range from 2 to 70 pct Zn. In addition to autoradiography, microhard-ness values were used to determine compositions on a micro scale. Solidification Experiments The alloys contained approximately 2. 6, 12, 20, 30, 50, and 70 wt pct Zn and the balance aluminum. According to published diagrams the eutectic reaction occurs at 382°C between the eutectic liquid (95 pct Zn), a (82.8 pet Zn), and $ 498.9 pct Zn). Solid-state reactions at lower temperatures (due to the miscibility gap between 350" and 275"C, the eutectoid at 275'C, and the precipitation from supcrsaturated a) did not affect this investigation. Even if they occurred to any appreciable extent, they did not alter the evidence pertaining to the solidification structures. The alloys had to be of high purity to avoid radioact~ve contamination during activation. The aluminum analyzed 0.015 pct Si, 0.009 pct Fe, less than 0.004 pct Cu, and less than 0.006 pct Mg with traces of sodium and titanium; the zinc was reported to be at least 99.99 pct pure with traces of iron and magnesium. The alloys were prepared under argon in an induction-heated, bottom-pouring furnace, and poured into a coated steel mold, which could be preheated to temperatures up to 700°C in order to control the rate of solidification. The pouring temperatures ranged from about 40" above the liquidus for 2 pct Zn alloys to about 130°C above the liquidus for 70 pct Zn alloys. As soon as the melt entered the mold, the readings of a thermocouple placed % in. above the bottom of the mold were recorded by a recording potentiometer. Cooling at the rate induced by the initial temperature of the mold was continued to a temperature 100°C below the liquidus; the mold with its contents was then quenched in icy brine. Quenching from a fixed interval below the liquidus was used to provide a standardized procedure, since the solidus and liquidus temperatures and the interval between them vary greatly over the composition range investigated. The temperatures from which the samples were quenched were below the equilibrium solidus, but under nonequilibrium conditions some liquid was still present. This residual liquid solidified during the quench. The samples measured 314 in. diam and 11, in. height. Drillings for chemical analysis were taken

Jan 1, 1957

By C. H. Wilson, J. W. Daly, J. J. Jakosky

Meteor Crater, Arizona, is a natural wonder which for years has been the subject of considerable discussion and study as to its origin and age (Fig. 1). Of the various theories advanced regarding the origin, two have been considered as most probable by a majority of investigators. The first theory is that the crater was formed by a meteorite or a swarm of meteoric material striking the earth at a high velocity and burying itself. The second theory is that the crater was formed by a "steam explosion" from hot solutions or gases coming from underneath the present sedimentary beds which overlie the area. In order to obtain more detailed information regarding the conditions existing at the crater, the present management decided to have a detailed geophysical examination made. The origin of the crater is of considerable scientific importance and interest. More or less active mining operations have been carried out during the past 20 years by various groups who believed that the crater was of meteoric origin, and who hoped that sufficient quantities of such material had been buried to be commercially valuable. Fragments of meteoric material found on the surface of the ground in the debris around the rim gave analysis of approximately 92 per cent iron and 8 per cent nickel, with some platinum and iridium. The material having a gross value of approximately $50 per ton, mining would be commercially profitable if sufficient quantities of the material existed in condition for mining. In the early work numerous drill holes and shallow shafts were put down, mainly in the northern portion of the crater. Pulverized material and debris caused considerable difficulty, and in an effort to overcome this the present management started a 1500-ft., two-compartment shaft on the south rim of the crater and outside of the fill zone. The intention was to sink the shaft in the solid rock outside of the crater, and then to crosscut toward the crater at a depth of 1500 ft. The work was finally stopped when a depth of 650 ft. was reached, because water poured into the shaft through large cracks and fissures in the rock. The enormous force responsible for the crater had also broken

Jan 1, 1932

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN : Submitted herewith are the report of the Treasurer for the year 1944 and reports for the same year of the following standing committees: Membership, Ad- missions, Papers and Publications, MIN- ING AND METALLURGY (Magazine), and Library. To these reports you are referred for additional details.

Jan 1, 1946

By R. L. Vaughn, H. R. Cooper

Effective procedures for automating X-ray assaying by use of a computer are described. These methods have advanced the reliability and accuracy of X-ray data, resulting in improved assay measurements for operations and process control. Assaying by X-ray fluorescence has been increasingly used in the mining industry, both for analyzing solid H.R. COOPER and R.L. VAUGHN, Members AIME, are Systems Manager-Process Control and Senior Systems Analyst, respectively, Scientific & Engineering Computer Center, Ken-necott Copper Corp., Salt Lake City, Utah. TP 68B236. Manuscript, Sept. 16, 1968. Discussion of this paper, submitted in duplicate prior to Dec. 15, 1969, will appear in SME Transactions, March 1970, and AIME Transactions, 1970, Vol. 247. samples for smelter, mill, and mine quality control and for continuous stream analysis of mill pulps. The important advantages of X-ray methods in laboratory assaying are reduced analysis cost, and for on-stream analysis, immediate assay information on concentrator streams. Of the numerous reports concerning X-ray analysis in mining operations, one is referenced which can be noted particularly in conjunction with this report.' Continuous X-ray analyzers have been installed at Kennecott and other mining companies for operations guidance and trend information for a number of years. However, complete operational acceptance of X-ray data has been slow, due* to the difficulty in maintaining

Jan 1, 1970