Search Documents

By L. Cichowicz, K. K. Millheim

The constant-rate drawdown test performance for a low-permeability, verticany fractured gas well was investigated. A series of gar wells were tested by flowing each well at constant rate until the data could be analyzed using con-ventional radial flow theory. Each well was then shut in to build up. After a sufficient buildup was obtained, another flow Iest commenced but at a higher flow rate than Ihe first test. Again, the well was shut in when radial fiow was obtained. his procedure was repeated for three to four different flow rates. Two wells in the San Juan basin were tested using this procedure. Both wellere fractured after completion, cleaned up and then shut in until flow testing commenced. Test designs of both wells permitted investigation of the most realistic values of egective permeability, wellbore radius and turbulence factor. Also, being able to determine the eflective fracture flow area and vertical fraclure efficiency was inherent with this testing approach. It was observed that fractures in both wells influenced the Pressure behavior for approximately Is to 40 hours (depending on the flow rate) before radial flow was evident. After this time, drawdown data were analyzed using radial pow theory. When a low-permeability gas well has vertitally oriented, induced fractures, the early flow geometry ic. essentially linear. It will be shown how to determine when a flow test has been conducted long enough so lha' the most representative values of effective permeahiiity. wellbore radius and turbulence factw can be calculated. From the linear pressure data, valuable information about The fracture treatment, such as the effective flow area and vertical fracture efficiency, can be determined for vertically froctured wells. Introduction During tests on gas wells in the Sari Juan basin7 initial transient behavior lasted for many days because of the low permeability of some porous media. As a result, stabilized flow performance could not be obtained. If these wells received some type of stimulation treatment, early pressure behavior deviated from conventional theoretical radial Row. When conventional radial flow theory was used to analyze these low-permeability fractured gas wells, larger values of flow capacity and absolute open flow potentials (AOF) sometimes resulted. Wells were assigned open flow poten- tials that proved to be 3 to 10 times higher than the well would sustain over a longer period of production. In some cases where the wells had flowed for longer periods of time during a constant-rate drawdown test, it was noticed that the effective flow capacity appeared to be decreasing with time until a certain value was reached. The early nonradial pressure behavior can be explained If linear flow is assumed. Rusell and Truitt mathematic. ally investigated the vertically fractured well in a bounded area. They showed that early flow behavior was essentially linear and, for x,/x. approximately less than 0.10 radial flow was obtained after short periods of time. Then realistic values of effective permeability and skin could be determined. Scotta experimentaliy studied the vertically fractured well with a heat flow analog. He showed that earb flow was linear, Both studies indicate that, for small values of x,/x,, linear flow approaches radial flow if the well is tested long enough, To help prove this concept of early linear flow caused by induced vertical fractures, two low-permeability gas wells were tested. Both wells received large fracture treatments prior to testing. A vertical fracture was indicated from the analysis of fracture treatments, As anticipated, tests of both wells indicated early linear flow that was later followed by a period of radial flow, Data collected from each well were analyzed. From the well tests, plus other information on each well, the effective permeability, wellbore radius and turbulence factor were calculated. Effective fracture flow areas calculated from test analyses for each well proved to be approximately one-fourth the created area calculated from classic hydraulic fracturing theory: other fractured wells that were tested but not presented in this paper also indicated that the effective fracture flow area was one-fourth to one-third the created area predicted from hydraulic fracturing theory. The vertical fracturing efficiency was estimated from the calculated values of effective wellbore radius and fracture flow area. For the two wells tested, calculated fracture lengths x, were 112 and 105 ft, and the vertical fracturing efficiencies E, were 122 and 183 percent. Development of Flow Model Agnew' showed that most induced fractures below 1,500 ft are vertical. Anderson and Stah15 indicated that most of the fractures they studied were vertical. Thc model proposed for early flow in most vertically fractured gas wells is shown by Fig. 1. This model should approximate early flow behavior until radial flow is reached, at which time a radial model with an effective wellbore radius of 0.5 they will

Jan 1, 1969

By R. E. Smallman, I. Milne

The deformation behavior of single crystals of Nb-Mo alloys has been investigated with particular reference to the influence of composition, orientation, and temperature. Strong solid-solution hardening was observed reaching a maximum at the equiatomic cotrlposition and can be attributed to the difference in atomic size between niobium and molybdenutrz. Changes in the form of stress-strain curve, as shown by a high work-hardening rate and restricted elongation to fracture, were observed at a composition of Nb-85 pct Mo and are attributed to the presence of MozC DreciDitate. Conjugate slip was only extensive in dilute alloy samples; at the 50/50 composition deformation rnainly occurred by primary slip, and the onset of conjugate slip gave rise to failure by cleavage on (100). The variation of yield stress of Nb-50 pet Mo with orientation was consistent with slip on (011)(111) slip systems. The temperature deperndence of the yield stress between -196" and 250°C was similar to that of pure bcc metals, but at a much higher stress level; no evidence for twinning %as found. IN recent years the deformation behavior of various pure metals in groups VA and VIA has received considerable attention, but surprisingly little work has been carried out on binary alloys made by mixing metals from the two groups. Such an investigation would be of interest since single crystals of metals of group VA have been shown to deform characteristically with a multistage deformation curve1"3 while a parabolic type of deformation curve has been reported for most of the group VIA metals.4'5 It has been suggested by Law ley and Gaigher~ that the difficulty encountered in obtaining multistage deformation curves for molybdenum in group VIA was possibly because of the presence of a microprecipitate of MozC which they observed even at carbon contents as low as 11 ppm. Recently a multistage deformation curve has been reported for molybdenum ," although the stages are not so definitive as those for group VA metals. The binary alloys of the particular refractory metals which have been investigated in single-crystal form include Ta-w,' Ta- Mo,' and Nb- Na." While a large amount of hardening was observed for alloys of the Ta-W and Ta-Mo systems, associated with room-temperature brittleness for alloys approaching the equiatomic composition, Ta-Nb remained ductile over the complete composition range with little or no solution hardening. Other systems have been investigated by hardness measurements on polycrystalline material and a discussion of the hardening of these alloys has been presented by ~udman." The purpose of the present investigation was to examine the deformation behavior of Nb-Mo alloys in detail, with particular reference to alloy composition and single-crystal orientation. In this way it was hoped to shed some light upon the restricted ductility of these alloy specimens. 1) EXPERIMENTAL PROCEDURE The starting materials were obtained in the form of beam-melted niobium rod and sintered molybdenum rod of suitable dimensions. Since niobium and molybdenum form a complete solid-solution series at all temperatures, alloy single crystals were produced by melting the two constituents together in an electron bombardment furnace (EBM). To produce specimens free from segregation a molten zone was passed over the length of each rod six times in alternate directions at a speed of 10 in. per hr. Typical specimens were analyzed for interstitial impurities by gas analysis and for metallic impurities by spectrographic analysis. The results of this analysis are shown in Table I. Many of the tensile specimens were also analyzed (after testing) by scanning the gage length in an electron beam microanalyzer, from which it was found possible to predict the approximate composition of a specimen from the original proportions of each element in the EBM. The tensile specimens were made with a gage length of 0.5 in. and diameter of 0.075 in., using a Servomet Spark machine. By careful machining on the finest range for the final i hr of this technique, surface cracks could be reduced to the level where they were easily removed by electropolishing in a solution of nitric and hydrofluoric acids. The specimens were strained at a rate of 10 4 sec-' using friction grips designed to prevent accidental straining and maintain a good alignment before straining. The orientations of the individual specimens tested are shown in Fig. 1 and the corresponding compositions listed in Table I1 together with collated experimental data. 2)RESULTS a) General Deformation Behavior. The effect of composition on the room-temperature deformation curves of similarly oriented specimens is shown in Fig. 2. The yield stresses of the pure constituents, while not the lowest reported to date, were at least comparable with existing data. Although the solution hardening was large for alloys at either end of the phase diagram, and comparable with the Ta-W solution-hardening data of Ferris et a1.,8 the low work-hardening rate characteristic of niobium was sustained until a composition of Nb-85 pct MO had been reached. Associated with the peak yield stress ob-

Jan 1, 1969

By Rossiter W. Raymond

I desire to call the attention of the Institute to a novel system of dredging which, it seems to me, may prove applicable, not only to river and harbor improvements, but also to certain varieties at 1east of alluvial and diluvial gold mining; that is, river-mining, barmining, coast-mining, and any other similar operations now carried on by means of coffer-dams or dredging machines. The simple and effective method to which I refer is the invention of General Roy Stone, formerly an officer of volunteers, and at present a civil engineer, engaged under General Newton, of the United States Engineer Corps, upon the government works in New York harbor. General Stone has been, since September, 1878, in charge of operations upon Diamond Reef. This reef, lying between Governor's Island and the Battery, is one of the most dangerous in the harbor. Its position in the highway of navigation, and the fact that it is dangerous only to vessels of considerable draught and at certain stages of the tide, combine to increase the serious nature of the disasters which it has caused. The reef consists partly of rock in place, and partly of deposits of glacial clay, boulders, and pebbles, over all of which lies, or did lie until it was removed, the ordinary silt and rubbish of the harbor. As the purpose of the present paper has nothing to do with the special dimensions and other circamstances of this particular work, I describe those features only which are connected with General Stone's ingenious device. Various attempts have been made to remove the upper portion of Diamond Reef and secure a navigable depth at low tide. Some years ago Maillefert undertook to accomplish this by firing charges of high explosives, simply laid upon the surface. He accomplished some good in the removal of projecting points and ridges; but as soon as the surface of the reef had become approximately level, his method was no longer effective. After the work had been taken up by the Engineer Corps, the well-known drilling-scow invented by General Newton was brought into action; and, SO long as holes could be bored and fired in solid rock, this process was effective enough. In the mixture of hard-pan

Jan 1, 1880

By Marius S. Darrow, William B. White, Rustum Roy

The PbS-PbTe systen has been studied by quench-ing and D.T.A. techniques f?om 400' to 1150°C. Runs were made in evacuated silica tubes so that all equilibria are at the vapor pressure of the system. Lattice parameters of the quenched salnples , measured by X-ray diffraction, show a complete crystalline-solution series existing over a narrow temperature range between approximately 805" and 871°C. An exsolution dome extends from a maximum of about 805"C (approximately 30 mole pct PbTe) to 1 and 96.5 pet PbTe at 400°C. A narrow melting region, deternined by D.T.A., extends form 918c (mp PbTe), The shapes of the liquides and solidus curves imply the existence of a minimum at 871°C at approximately 65 pct PbTe. THe exact composition of the minimum could not be established due to the very narrow two-phase region. At compositions containing less than 50 pet PbTe, liquidus temperatures begin to increase, while the solidus remains almost flat to about 15 mole pet PbTe before beginning to vise toward the mp of PbS (1075 C). LEAD sulfide and lead telluride are isostructural (NaC1 type) semiconductors whose electrical and optical properties have been extensively studied and used in recent years. If appreciable crystalline solution exists between these compounds, the variation of physical properties with composition could be of interest. The purpose of this investigation was to determine the extent, if any. of crystalline solution, and to obtain the phase diagram for the system. To the knowledge of the authors, only three studies of the system PbS-PbTe have been reported, and, in chronological order, each investigation found an increasing amount of crystalline solution. In 1956, Yamamoto reported finding no evidence of crystalline solution between the compounds. Sindeyeva and Godov-ikov,' in 1959, found very limited crystalline solution. but only under conditions of excess tellurium concentration. Finally Melevski s3 investigation in 1963 indicated that one solid phase exists in the region from PbS to 7 pct PbTe and from 82 pct PbTe to PbTe at 886'C, with an eutectic at 55 pct PbTe at that temperature. Detailed data on the solvus boundary were not given. EXPERIMENTAL EQUIPMENT AND MATERIALS Commercially produced PbTe and PbS powders were used as starting materials. Batches of specific mole percent composition were accurately weighed and mixed in a plastic bottle, in a shaker mill. An analy- sis of impurity content is given in Table I for pure PbS and PbTe and for two randomly selected batches after the powders were mixed. Individual samples, ranging in weight from 0.2 to 0.5 g, were sealed in evacuated silica tubes which had been thoroughly washed and rinsed with acetone and distilled water. Thus all data taken were at the pressure of the system. Subsolidus relations were studied down to 400°C by heating the samples in a vertical tube furnace for 24 hr. The sealed tubes were quenched in water with quench time from the hot zone not exceeding 1 sec. Temperatures were measured by a chromel-alumel thermocouple and controlled to 53°C for most runs. The number and composition of phases present were determined from powder X-ray diffraction patterns taken at room temperature on a Norelco diffractome-ter, using silicon as an external standard. Above 850°C quenching techniques were, in general, found to be unsatisfactory, and differential thermal analysis (D.T.A.) was used to determine melting relations. The evacuated tubes were recessed about 1 cm at one end to accommodate the differential thermocouple. Al203 was used as the reference material in a similar tube containing the other side of the differential couple. For temperature measurements, a separate thermocouple was placed in the recess of the tube containing the sample to be measured, thus providing an opportunity to obtain thermal, as well as differential, analysis. All thermocouples for these measurements were Pt-Pt 10 pct Rh. Temperature and differential curves were recorded separately on synchronized strip-chart recorders. Thermocouples and recording equipment were calibrated using NaCl and gold standards, using the melting points 801" and 1063 C, respectively, which span most of the temperature range of interest. Heating and cooling rates generally were from 4 to 7°C per min. It was found, in fact. that rates ranging from 1.5 to 25°C per min did not significantly change the data obtained.

Jan 1, 1967

By W. Hurst, R. E. Leeser, W. C. Goodson

Three aspects of gas deliverability are presented in this paper. The first treats with the gas deliverability or availability of a normal depletion-type dry gas field. Such encompasses not only the period of stabilized constant rate, but more so, the "tailings" when a fixed abandonment pressure is reached and the rate by necessity must decline. A comprehensive work plot is offered, developed from mathematics herein included, that removes the triai-and-errnr computations that attended such undertakings in the past. The second part treats with the discount factor of the open flow potential constant from what is observed initially in testing a gas well to what is evidenced when stabilization is reached. This prevails in tight formations, such as the Kansas Hugoton field which is offered as the example. The means of establishing this factor are pressure build-up curves which, as sustained by analytical deductions, reproduce this entire period of transient flow under conditions of a constant rate influx. Finally, what is offered in this paper is the deliverability performance of an exceedingly rich gas condensate field producing from a tight formation. The example shown is the Knox Bromide field in Oklahoma, producing from the Bromide formations. The results are ominous, showing early reduction in permeability to gas pow, due to the retrograde condensate forming in the pore space, with the attending early logging-up of these wells. The analytics of lowered permeability are incorporated in the gas deliverability formula along with the PVT data that gives the increased condensate liquid saturation as the gas flows to the well bore. This paper would not be complete without a critique oflered at the end. With the many gas wells now in production and those that have completed their life, there has been no factual information collected by any source as to what constitutes that permeability range where a gas well would be unimpaired in its gas deliverability by the presence of rich condensate content, and the lowered range where such would be harmful. This question confronts all producers. INTRODUCTION Various aspects of gas deliverability are presented in this paper that includes depletion-type reservoirs, deteriora- tion factor of the gas deliverability constant, and the performance of a rich gas condensate reservoir producing from a tight sand. With respect to the presentation of gas deliverability and its tailings for depletion-type gas reservoirs, one notes that this is essentially the information offered by every gas transmission company and producer appearing before the Federal Power Commission for Letters of Conveyance in the dedication of reserves. In the ordinary procedure, as many engage upon this study, trial-and-error calculations are included, particularly as apply to the tailings. For many years one of the writers has employed mathematical analyses to perform this step and avoid the complexities so associated. In the preparation of this paper these analyses have been amplified to include any slope n for the open flow potential relationship for which the tailings can be determined from Fig. 1. With reference to the deterioration or discount factor of the open flow potential constant as such occurs in the gas deliverability formula, this for the most part has been an unexplored subject. Although the issue first appeared in the Kansas Hugoton field, where such was surmised but only recently resolved, this situation of a deterioration of the gas deliverability constant can occur wherever dry gas production from a tight sand is encountered. The first concerted attacks upon this problem were the presentations of Hurst' and Goodson' before the Kansas Corporation Commission to show that transient fluid flow and unsteady-state flow formulas prevailed. This was amplified later before the Federal Power Commission3 to show that this deterioration factor could be identified from pressure build-up curves. This has been reported by McMahon.4 Its importance to the industry merits the review of these essential features in completing the program on the aspects of gas deliverability. Finally, as illustrated here, for a low permeability formation such as the Knox Bromide field where the gas is rich, representing some 165 bbl of condensate per MMcf of effluent gas, the gas deliverability can be of limited extent in the life of the field, leaving substantial amounts of condensate and gas unrecovered. In cases such as this, gas cycling is mandatory. This is particularly revealed by the fluid mechanics introduced here, employing factual field as well as laboratory data, to show this-restriction upon gas deliverability. PRESSURE DEPLETION What will now be offered is the study of gas deliver-

By D. L. Kelley

High-viscosity water injection has been proposed for use in reservoirs containing high-viscosity crude oils. Previous publications have largely ignored the possible effects of the connate water on the proposed process. This paper describes experimental work which indicates that the connate water will be forced ahead of the injected water to form a bank of low-viscosity water. This decreases the oil recovery which would be expected if such a bank were not formed. These effects are shown for a range of fluid mobilities and connate-water saturations for a five-spot injection system. In general, oil recoveries using viscous water are significantly greater than for untreated water even though they are less than would be expected if no connate water bank were formed. INTRODUCTION The effect of mobility ratio on the oil recovery of wa-terfloods has been known for many years. Muskat first pointed out that the fluid mobilities (k/µ) in the oil and water regions would affect the performance of the water-flood, and he estimated the general effect of these variables.' Since this early work, studies of the effect of mobility ratio on secondary recovery have been reported where mathematical,' potentiometric3 and scaled flow models' were used. These studies have shown that a reduction in the mobility ratio between the oil and the displacing fluid would cause additional oil recovery when water-flooding reservoirs containing viscous crude oils. Studies reported by Pye- nd Sandiford 8 have indicated that chemicals to increase injection water viscosity are now available and can be used to reduce the over-all mobility ratio of a waterflood. Where mobility ratios are controlled by the injection of viscous fluids, the connate water of the reservoir can play an important part in the displacement of the reservoir oil. The purpose of this study was to determine the effect of the connate-water saturation in waterfloods where viscous waters are used for injection. DISPLACEMENT OF THE CONNATE WATER Russell, Morgan and Muskat7 were the first to recognize the mobility of connate waters in waterflooding. They conducted waterfloods on oil-saturated cores containing 20 and 35 per cent irreducible water saturations, and found that from 80 to 90 per cent of the "irreducible" water was produced after only one pore volume of water was injected. However, their experiments were conducted at rates of flow significantly higher than those ordinarily occurring in waterfloods. Also, the cores were only from 4.0 to 8.5 cm long. Brown 4 studied a 100-cm linear sand pack which had been prepared to contain connate water and oil. He used 140- and 1.8-cp oils with injection water of essentially the same viscosity as the connate water. He found that all of the connate water was displaced by the injection water in both cases. However, the injection volumes required for complete displacement of the connate water were considerably higher in the case of the more viscous oil. To verify the results of the foregoing experiment, a 10-ft-long linear model was constructed by packing 250-300 mesh sand in a 1/2-in. diameter nylon tube. The model was evacuated, saturated with a brine of 1-cp viscosity, and flooded with a 41-cp mineral oil to the irreducible water saturation of 10.9 per cent. The model was then waterflooded by the injection of a water solution which had an apparent viscosity of 42.6 cp. The solution consisted of 0.5 per cent methylcellulose in distilled water. The viscosities of the oil and connate water were measured with an Ostwald viscosimeter. The viscosity of the polymer solution was calculated by Darcy's law using pressures measured during actual flow conditions. The ratio of the mobility in the oil region to the mobility in the inject ion-water region was approximately 0.32. The mobility ratio of the oil region to the connate-water bank was approximately 14. The mobility ratio between the connate-water bank and the injection water region was 0.024. Approximately 84.5 per cent of the recoverable oil was produced before water breakthrough. Immediately following breakthrough, oil and connate water were produced at an increasing water-oil ratio until the viscous injection water broke through. At viscous-water breakthrough, 96 per cent of the original connate water had been produced. After breakthrough of the viscous water, there was no additional production of connate water or oil. The near-

Jan 1, 1967

By W. L. Penberthy, H. J. Ramey

Experimental work on the combustion oil recovery process has consisted of both laboratory and field studies. Although field experiments are the ultimate test of any oil recovery process, they are costly, time consuming and difficult to analyze quantitatively. Laboratory combustion tube experiments can be opertzted far more rapidly and cheaply, but are subject to scaling and interpretation problems. This paper points out some important design problems, operational criteria and considerations in2portunt to interpretation of results. An analytical hcut model of movement of a burning front axiully along a cylinder with heat loss through an annular insulation was developed. The result was used to identify steady-state temperatrrre distributions both ahead of and behind the burning front, with and without heat loss. Results indicate potential operating limitations on the minimum burning front rielocity (or air flux) which may be used for any given combustion tube. Results also enable estimating the effective thermal diffusivity and over-all heat loss from experimental data and thickness of the brnning zone. Resu lts of operation of a combustion tube constructed recently verify this preliminary theory in the region immediately ahead of and behind the burning front surprisinRly well. INTRODUCTION Many field and laboratory studies of the forward combustion oil recovery process have been conducted since the early publications of Kuhn and Kochl and Grant and Szasz2 in 1953 and 1954. In view of the complex and costly nature of this type of investigation, it is not surprising that no complete theory of the nature of the forward combustion Drocess is yet available. However, gross effects are understood well enough that reasonable design procedures are available for planning field operations. Nelson and McNeil 3,4 have published two comprehensive papers concerning design procedures. One major consideration in planning field operations is the fuel concentration at the burning front. Fuel concentration controls air requirements — an important cost factor in forward combustion. Although fuel concentration can be estimated from field test results by various methods, results are subject to great uncertainty in view of natural limitations on experimental observations. Nelson and hlcNeil4 recommend that fuel concentration be determined from laboratory combustion tube studies. Fuel concentration is only one of many important factors which can be studied by combustion tube experimentation. An obvious goal of imporrance must be development of a comprehensive theory of the forward combustion process. If a theory of this process can be established which matches controlled laboratory experimentation, it should be possible to apply this theory to field operating conditions with some confidence. Laboratory combustion tube studies have already yielded important information concerning the combustion process. However, details concerning the design, construction and operation of combustion tubes are rare. Combustion tubes used by various investigators vary in size, length and mode of operation. Therefore, one purpose of this paper is to present considerations important to design, construction and operation of a combustion tube. In regard to previous combustion tube studies, attention is called to Refs. 1 through 9. These references describe a wide variety of equipment types and present a great deal of pertinent experimental data. In general, combustion tubes usually consist of thin-walled stainless steel tubes containing an oil sand pack mounted within a pressure jacket. Provisions have often been made to heat the tube ex tern a lly by separately controlled heaters to reduce heat losses. This step usually permits operation at low air fluxes (air rate per square foot burning front surface) similar to those encountered in field operations. Burning is usually conducted from the air inlet end of the tube to the outflow end. The tube orientation used has been vertical or horizontal. For vertical tubes, burning has been conducted vertically downwards. As a result of laboratory studies, many of the

Jan 1, 1967

By H. S. Choi, I. Iwasaki

The effect of temperature as a parameter in ore flotation has not been systematically studied, although for some ores it has been known for many years that selectivity and grade of concentrates can be improved by conditioning or flotation at moderately or substantially elevated temperatures. In 1934 Coghill and Clemmer' stated that "elevated temperature seems to make hard water more tolerable" in soap flotation, and a cursory examination of the literature indicates that some earlier investigators were aware of beneficial results obtained by floating above room or mill-water temperatures. Tartaron,2 Mitchell et aL.,3 and particularly Hamilton et al.' have shown that high pulp temperatures give high recovery and selectivity in soap flotation of fluorite from a variety of gangue minerals. As a result of the work of these and of other investigators, high-temperature flotation has been successfully applied to industrial flotation of fluorite. Falconer" stated: "The use of high temperature conditioning (above 35°C and preferably above 60°C) in connection with the soap flotation of nonsulphide ores, as covered in B. Kalinowski's French Patent No. 847,-215, Dec. 7, 1938, is claimed to provide more intense activation, better separation of values from gangue, and reduction in quantity of reagents." The various investigations quoted above clearly demonstrate the improvements to be realized by increasing the temperature at which fluorite is floated, and it is surprising that little or no information has been published on systematic investigation of the same method as applied to other ores. The present article describes comparative results obtained at room temperature and at elevated temperatures by otherwise conventional flotation of iron ores, by single-mineral flotation in the Hallimond tube, and by contact-angle measurements. It is not the purpose of this article to evaluate the commercial feasibility of high-temperature flotation of iron ores, although preliminary calculations show that the cost should not be excessive and that the gains to be realized may well outweigh the extra cost of heating the pulp. LABORATORY FLOTATION TESTS Experimental: All flotation tests reported in this article that use a laboratory Fagergren cell were made on ore A (either containing the primary slimes or deslimed at 20µ as specified) following the preparatory procedures described elsewhere- or this particular ore. Ore A contained hematite, goethite (limonite), quartz, chert, and minor quantities of magnetite. Confirmatory tests made on other ores show that the same general principles apply to ores of similar mineralogy and structure. Conditioning was performed by adding the collector, as a soap, to the vigorously stirred and heated pulp. Conditioning time was 5 min, the pulp contained 60 pct solids, and the equivalent of 0.5 Ib of fatty acid was added per ton of original (unde-slimed) ore. The pH of the pulps ranged from 6.8 to 7.1 (25°C measurement) during conditioning. The pH was adjusted in the flotation cell by addition of either NaOH or H2SO4, the values reported being those of the pulp cooled to 25°C. During conditioning and flotation the pulp temperatures were controlled within l° to 2° by immersion of Variac-controlled Calrod elements in the conditioning beaker and in the cell, and by the use of water, heated to the appropriate temperature, for transferring pulp, adjusting pulp volume, and washing. Selectivity indexes have been calculated on the same basis as those reported in the article by Cooke, Iwasaki, and Choi." Results: Table I gives the results obtained by floating deslimed ore A with pure oleic acid at 25" and 50°C, and Fig. 1 shows the selectivity indexes plotted against pH of flotation. Inspection of Table I

Jan 1, 1961

By K. E. Gray, G. M. Myers

In previous publications,5 results of single-blow bit tooth impacts on saturated rocks at various stress states were reported. This paper extends these earlier works to include study of bit impact tests on salt water-saturated Berea and Bandera sandstone samples under conditions of elevated confining and pore pressure. During the tests dynamic filtration and deposition of a mud cake were occurring due to the presence of drilling mud in the borehole and a borebole-to-formation pressure differential. Results indicate that saturation of these sandstones with salt water tends to make them weaker than when saturated with nonreactive fluids. Plastic failure often occurs even when extremely high fluid-loss muds are present in the borehole. The failure mode tends toward plasticity with decreasing fluid loss. Brittle failure of sandstones in mud-filled holes is apparently relatively rare. Depending on the stress level, and the associated failure mode, withdrawal of the bit tooth induces a tensile force that seems rather important relative to the quantity of rock removed by vertical tooth impact. INTRODUCTION A vast majority of the oil wells drilled today involve the use of colloidal muds having a measurable mud filtrate loss. It is known from field experience that reduction of the water loss of a mud generally results in a reduction of the penetration rate. This paper describes an investigation of crater formation at simulated bottom-hole pressure conditions for drilling fluids having different water losses. The literature on single bit tooth impact (cratering) at atmospheric conditions is extensive, but only a limited amount of work has been performed at the stress conditions similar to that found in oil wells. Spherical penetrator cratering tests on rocks at hydrostatic pressure were performed by Payne and Chippenda1e.1 Chisel impact studies on limestone with independently varying overburden and borehole pressure and atmospheric pore pressure were reported by Garner, et al.2 Gnirk and Cheatham3 performed "static" penetrator tests on dry rocks at equal overburden and borehole pressures. Podio and Gray4 studied the effect of pore fluid viscosity at atmospheric pore and borehole pressures and varying overburden pressures. Their results illustrated the importance of fluid saturation of the rock. Yang and Gray5 reported single tooth impact tests on saturated rocks at elevated borehole, pore and confining pressures, but with equal pore and borehole pressures. For the work reported in Refs. 4 and 5, filtration across the hole bottom purposely was avoided. Maurer6 has investigated the effect of independently varying pore and borehole pressures at elevated overburden pressures by using a zero water-loss mud in the borehole. His tests were carried out under conditions that allowed independent control of overburden, pore and borehole pressures, but without control of filtration at the hole bottom. EXPERIMENTAL APPARATUS AND PROCEDURE APPARATUS The single blow chisel impact apparatus used by Garner,2 as modified for this study, is shown in Fig. 1. A cross section of the pressure vessel is shown in Fig. 2. Several pieces of auxiliary equipment were added to the original apparatus in order that the borehole and pore pressure could be applied in a manner analogous to the actual bottom-hole situation. The pore-pressure system included a filtrate volume-measuring transducer and had sufficient surge capacity to allow filtrate to be injected into the sample without significant changes in pore pressure at points remote to the borehole. The borehole-pressure system contained a cross connection to the pore-pressure system so that both systems could be pressured simultaneously. The borehole-pore pressure differential was applied rapidly by the use of a quick and full-opening valve. The operation of this valve triggered two industrial

Jan 1, 1969

By Werner Schwartz, Wolfgang Haase

Lead sulfide concentrates, which may include other lead concentrates, are sintered on an up-draught sintering machine without the addition of any diluting agents or fluxes. Subsequently they are melted in an oil- or gas-fired rotary furnace. The sintering and melting processes are based upon the following roast-reaction: PbS + 2 PbO = 3 Pb + SO, PbS + PbSO, =2 Pb + 2 SO, For obtaining a lead bullion free from sulfur, the sintering process is carried out in such a way that the sinter product contains a small amount of excess oxygen above that to react with the sulfides. At the end of the melting process, when the reactions are finished, the remaining small amount of oxide residues is reduced with coal to which a certain percentage of soda ash (about 1 pct of the lead bullion) is added. For the lead smelting process described neither coke nor fluxes—except soda ash—are required. This process is being utilized by a European smelter successfully and with a high lead recovery. The consumption figures for the smelting of 100 tons per day of lead concentrates are indicated. The lead content of the lead concentrates from modern ore dressing plants ranges from 65 pct to above 80 pct. In most lead smelters of the world these concentrates are smelted in a blast furnace. For blast-furnace smelting the concentrates have to be desulfurized and agglomerated by sintering. A requirement for the perfect operation of a down-draught sintering machine and of a blast furnace is a maximum lead content in the feed of 40 to 45 pct. For this reason, some lead concentrates have to be diluted by adding return slags, limestone, and possibly iron oxide and sand. As an example, 100 tons of lead concentrate with 72 pct Pb would contain 13.5 tons of gangue (including the zinc). To produce a perfect sinter with 42 pct Pb it would be necessary to add 70 tons of flux and return slag, more than five times the original weight of the gangue, to the sinter mix and blast-furnace charge. A correspondingly large amount of coke would be required in order that all of these materials reach the heat of formation and the melting temperatures of the slag (1200" to 1400°C) inside the blast furnace. The roast-reaction process presents a possibility for lead recovery without dilution of the concentrates. In this process the concentrate mixed with coal is placed upon a Newnam-hearth and air is blown through nozzles into the heated mix. AS a result metalllic lead and a relatively great amount of so-called .'Grey Slag" with a lead content of 25 to 35 pct are formed. The slag is sintered to eliminate sulfur and, after addition of the requisite fluxes, treatt:d in a blast furnace. Owing to the poor recovery of lead from the hearths and to the unavoidable heavy hand-work plus the risk of poisoning this process is utilized in very few 112ad smelters today. Since in mxny countries of the world coke is expensive and difficult to obtain, it appeared feasible to use the principle of the roast-reaction by modern sintering and melting methods with recovery of the lead in electric, or oil, gas, or coal-fired furnaces. Two processes are utilized on an industrial scale: A) Lead smelting in the electric furnace of the Bolidens Gruv A/B in Sweden, as described by S. J. Walldcn, N. E. Lindvall, K.G. Gorling, and S. Lundquist. B) The self-fluxing lead smelting of Lurgi Gesell-schaft fiir Chemie und Huttenwesen m.b. H., Frankfurt a M, Germany, which is described in this paper. In the Boliden process referred to above the sinter mix is pelletized by enveloping return fines with layers of flue dust, limestone powder, and dried galena concentrate. The roasting and agglomeration are carried out on a down-draught machine, and a slight excess of sulfur is left in the sinter product. During the smelting in the electric furnance the roast-reactions occur and a slag poor in lead and a sulfur bearing lead are formed. This latter is subsequently oxidized in a converter to obtain lead bullion and dross. The Lurgi-process achieves the maximum possible extent of the roasting reaction on the sintering machine. The wet flotation concentrates are blended with return fines (lead content 70 to 80 pet), any existing flue dusts and lead slimes—but without the

Jan 1, 1962

By D. W. Lillie

It has been demonstrated that considerable bend ductility exists in bulk specimens of polycrystalline high-purity silicon. The possibility of hot-forming at 1200°C is suggested. EXCELLENT corrosion resistance in many media and low cross section for absorption of thermal neutrons (0.13 barn) would make silicon of interest to nuclear engineers were it not for extreme brittle-ness and the difficulty of fabrication by any reasonable means. The use of silicon for structural purposes also has been considered in view of its light weight and oxidation resistance. Johnson and Han-sen' have investigated the properties of silicon-base alloys and concluded that there was no way of making pure silicon or silicon-rich alloys ductile at room temperature. In view of reports of appreciable ductility in germanium single crystals above 550°C'." and some plastic deformation in single-crystal silicon above 900oC,' the present investigation was undertaken to define more precisely the limits of high-temperature ductility in pure silicon. After this investigation was begun torsion ductility in both germanium and silicon was reported by Greiner." Through the courtesy of F. H. Horn, a small bar of cast extra high-purity silicon was obtained and small bend specimens were made from it by careful machining and grinding. All of the reported tests results were obtained from samples from this bar (bar No. 1) and one other of similar source (bar No. 2). No complete analysis was obtained but, based on analysis of similar semi-conductor grade material, metallic impurities were under 0.01 pct total. Vacuum-fusion analysis for oxygen showed a value of 0.0018 2 0.0003 pct for the first bar tested and metallographic analysis showed no evidence of a second phase. Bend tests were carried out on an Instron tensile machine using a bend fixture with a 1 -in. span loaded at the center. Supporting and loading bars were 0.250 in. round and the load was applied by downward motion of the pulling crosshead of the machine. Specimen thickness and width were approximately 0.10 in. and % in. respectively. Loading rate was controlled by holding crosshead motion constant at 0.02 ipm. In some cases a smaller specimen was used on a 5/8-in. span with a 0.129-in.-diam loading bar. The entire bend fixture was surrounded by a hinged furnace and all heating was done in air atmosphere. Temperature measurement was made with thermocouples fastened directly to the bend fixture within less than 1 in. from the specimen. Autographic stress-strain curves were recorded during each test, and breaking load, total deflection, and plastic strain could be obtained from these curves. Stress was calculated from the beam formula S = 3PL/2bh2, where P is the load in pounds, L the span in inches, b the specimen width in inches, and h the specimen thickness in inches. This formula is strictly correct only in the elastic range but has been used to calculate a nominal stress for convenience in the plastic range. The stress given is the maximum stress in the specimen. Results The results of the complete series of tests are shown in Table I. The first group of tests (specimens Nos. 1-6) showed the beginning of plastic flow at a test temperature of 900°C, so two additional tests (Nos. 8 and 9) were made at 950°C on small-size specimens from bar No. 2. Specimen No. 8 was tested in the as-machined condition, and No. 9 was heat-treated in hydrogen at 1300°C for 2 hr, cooled to 1200°C and held 1 hr, cooled to 1000°C and held 1 hr, cooled to 900°C and held 1 hr, and finally cooled to a low temperature before removal from the hydrogen. It is apparent that the heat-treatment had a significant effect on yield strength and ductility. In addition, the magnitude of the yield point was conslderably reduced in the heat-treated specimen as is shown m Fig. 1 by tracings of the stress-strain curves. After obtaining a furnace capable of reaching higher temperatures specimens Nos. 10 to 13 were tested at 1100 and 1200°C. Strain rate was increased by up to a factor of 10 to see whether the ductility observed was excessively strain sensitive. Specimen NO. 10, strained at 0.02 ipm and 1100oC, was still bending at a deflection of 0.322 in. when the load rate was increased to 0.2 ipm, resulting in immediate

Jan 1, 1959

By R. W. Parsons, P. R. Chaney

Oil recovery by the imbibition mechanism can be important in fractured carbonate reservoirs with a bottom water drive. Laboratory experiments were performed on water-wet carbonate rocks to model this process. The results are interpreted in light of the applicable scaling laws. The imbibition production behavior of a pillar of rock subjected to a slowly rising water table can be synthesized from data on total immersion experiments on small rock samples. If the rate of water table rise is slow enough and if the physical properties are such that the imbibition zone is of a small vertical extent, then only the final oil recovery on the small samples need be known. Applying laboratory imbibition data to a real reservoir should be done with caution because of possible wettability problems and the unknown behavior of two-phase flow in fractures. INTRODUCTION The spontaneous taking up of a preferential wetting fluid into a porous medium with the simultaneous expulsion of the contained fluid is termed imbibition. One of the many physical imbibition processes is the production of oil by the taking up of water into a water-wet reservoir rock. In certain types of heterogeneous reservoirs, e.g., fractured, it is realized that imbibition alone may be the dominant mechanism. Theoretical studies of imbibition oil recovery have followed several lines of attack. The behavior of certain mathematically tractable and conceptually simple models have been analyzed. Birks1 considered a bundle of vertical capillaries model, while Perotti et al.2 and Kelemen3 used a model of a series of vertically oriented fractures. If the oil production behavior from a block of reservoir rock is known, then the cumulative behavior of a vertical stack of these blocks subjected to a rising water table can be determined by a method outlined by Aronofsky et al. 4 Knowing the capillary pressure and relative permeability functions should uniquely set the imbibition behavior for a given sample. Solutions of the partial differential equations describing the process, however, present some formidable problems. Digital computer techniques have been applied to displacement processes in which the capillary pressure has been included.5"8 More recently, similar techniques have been used by Blair 9 to calculate countercurrent imbibition behavior. The fact that imbibition behavior is described by the usual fluid flow equations (Darcy's Law and continuity equation) implies that the derived scaling laws should apply equally to this situation. Use of model experiments to study imbibition has been employed by Graham and Richardson 10 and Mattax and Kyte,11 who actually tested the scaling law applicability. This study is concerned with scaled model imbibition experiments on water-wet carbonate rocks. Of particular interest is the slowly rising water table experiment. This simulates a highly fractured reservoir with the water table rising uniformly through the vertical fracture system. Experiments were performed on different sized samples and with different rates of rise of the water-oil interface surrounding the rock pillar. Total immersion imbibition experiments on smaller rock samples were performed to test the basic linear scaling laws and to see if these simpler tests could be used to synthesize the rising water table experimental results. THEORY IMBIBITION SCALING LAWS Scaling laws for the flow of two incompressible immiscible fluids in a porous medium have been presented by Rapoport.12 These are derived directly from Darcy's Law for the individual phases and the continuity equation. Results from a laboratory model experiment will duplicate those from some reservoir prototype if a constant proportion is maintained among the three forces acting on the fluids — the capillary pressure gradient, the gravitational gradient and the flowing pressure gradient. Operation of the model (i.e., fluid injection or withdrawal) must be conducted in accordance with specific equations. If the

Jan 1, 1967

By W. Allen

FOR the past six years gravity surveys have been used for underground prospecting in the copper mines at Bisbee, Ariz. The primary purpose of the surveys has been to reduce the diamond drilling and crosscutting necessary for exploration. Since many of the orebodies are small, and geologic control is not always apparent, any information that will direct the drilling and crosscutting is highly desirable. Because of extensive development and exploration work in the copper mines at Bisbee, it has been possible to cover more than 630,000 ft of crosscuts on 30 levels with the gravity surveys. In the process the gravity procedures have been refined to a high degree. Density Contrast: For a gravity survey to be successful, a sufficient density contrast must exist between the geologic feature sought and surrounding host rocks. Most mineralized areas will provide this contrast if fairly massive bodies are present. In the Bisbee area the entire sequence of formations, except for alluvium, appears to have specific gravities ranging from 2.65 to 2.70. These values have been determined by means of a large number of cut samples and diamond drill cores. As a further check, vertical gravity differences have been used where nonmineralized sections are known to occur.' The only known major gravity disturbances result from mineralization that has increased the density and the voids that have decreased density. The voids are caused by mining operations and by underground water movement that has developed several areas of caverns. Equipment: While not absolutely essential, a small rugged gravity meter, such as the Worden meter, is highly desirable. A tall tripod, about the height of a transit tripod, permits instrument set-ups in deep water and in locations where fallen timber and muck piles make it impossible to use a short tripod. An additional advantage of a tall tripod is that it places the meter in the center of the crosscut, reducing the error caused by the crosscut void. Size and weight are important, since the only satisfactory means of operating the meter underground is to carry it by hand. A backpack can be used in rare instances but is usually a hindrance because of the close station spacing. The operator's ability to move through tight clearances will improve survey coverage, as it is then possible to move through raises and caved areas and to pass mine cars and machinery with a minimum of trouble. Station Control: Gravity stations are normally located every 100 ft along the crosscuts, at each intersection, and in the face of all stub crosscuts. In areas of high gravity relief, or where small anomalies might be expected, stations may be located at 25 or 50-ft intervals. When possible, the stations should be offset to avoid effects of raises or other voids. The gravity stations on a level are tied to one or more base stations, which are usually located at the shaft or near the portal of an adit. The base stations may be part of a gravity control net that extends to each level in the mine as well as to the surface. Such a net extending throughout the potential area of the surveys is highly desirable, as it is then possible to compare all gravity stations on a uniform basis. The stations that are part of the base net should be carefully established by multiple readings and, if necessary, by a least squares adjustment of the loops. In some instances where levels do not have a shaft station, or where access may be blocked by caving, it may be necessary to establish secondary bases at the top and bottom of the raises that are between levels. Under fair conditions 70 to 90 gravity stations can be located and run in 6 hr by a two-man crew. The best field procedures depend on conditions. Reduction of Field Data: Most of the time required to produce a final gravity map is consumed in processing the data. Each meter reading must be corrected for a minimum of five factors that affect the gravity value in addition to the density contrast being sought. These factors are 1) instrumental drift, 2) station elevation, 3) topography, 4) latitude, and 5) regional gravity gradient. Mine openings, such as stopes and raises, will affect the value. However, it is seldom practical to make corrections for these voids. Usually a rotation is made on the field note on the station, and any

Jan 1, 1957

By T. E. Seidel, A. U. MacRae

The dependence of the electrical and crystalline properties of silicon containing ion implanted boron atoms have been studied as a function of the incident dose, substrate temperature, and annealing tempera-ture. Hall effect studies show that the compensation due to defects is negligible after annealing at and above 500°C for a dose of 1013 ions per sq cm. Steps occur in the isochronal annealing curve for the sheet resistance at 300°C and 800°C and the mechanisms responsible for these steps are discussed. The range of the ions at 150 kev is 3500 * 5001. Electron diffraction studies on samples implanted with 150 ker ions show the existence of damaged (polycrystalline) silicon closer to the surface than the range of the ions. Etching and subsequent annealing of etched and unetched specimens suggest that the poly crystalline silicon is closer to the surface than the bulk of the distribution of ions. THE purpose of this study is to investigate some electrical and crystalline properties of ion implanted boron in silicon. Sheet resistance, Hall measurement, depth distribution by chemical staining, thermal probe and electron diffraction have been used to study the properties of samples implanted in a random direction with ions having energy up to 150 kev. The boron-silicon system has been the subject of considerable study'-7 due to its possible application in the fabrication of electronic devices. The implanted ions produce considerable crystalline damage to the substrate crystal before they lose most of their primary energy and come to rest. Fortunately, most, if not all, of this damage can be removed by subsequent annealing or by holding the substrate at an elevated temperature during the implantation process. Sheet resistivity measurements of the p-type layers produced by boron implantation into room-temperature silicon, reveal that the annealing occurs in a two-step process: the first occurring at -300°C and the second at -800°C.' Electron-microscope and low-angle electron diffraction studies of this damaged material indicate that the bombarding ions produce an amorphous silicon region about the trajectory of each ion.' At high doses, these damaged regions overlap and an amorphous surface layer results. Furthermore, the 800°C annealing step, appears to be associated with the elimination of this gross damage. The depth distribution of the as-implanted and also the annealed samples have been studied by an angle lap and staining technique as well as by Hall measurements.3-7 We find the experimentally determined ranges of the boron are less than those calculated by the Lindhard-Scharff-Schiott theorys (hereafter referred to as the LSS theory). Our results are in essential agreement with pre- vious results. In addition, we have made Hall measurements on samples bombarded with a low dose (2 x 1013 ions per sq cm) to minimize impurity banding effects, and find that deep ionized levels influence the carrier concentration and room-temperature hole mobility until the sample is annealed at temperatures above 500°C. Above this temperature, the data corresponds to that obtained when silicon is doped with boron by conventional techniques. We have also made a depth distribution determination of the crystalline damage due to the implanted boron by using glancing angle electron diffraction techniques. It was found that the gross damage depth distribution of heavily implanted samples is closer to the surface than the depth distribution of the electrically active boron. By removing this gross damage, without affecting the distribution of the implanted boron, we have determined that the 800°C annealing stage is not exclusively due to the improvement in the crystalline perfection of the amorphous material but also appears to be associated with the annealing of some point defects. These results and their relation to previous results are discussed in the following sections. IMPLANTATIONS Boron ions were implanted into silicon samples using an accelerator capable of operating from 10 to 150

Jan 1, 1970

By G. W. Thomas

A simplified mathematical model of underground conduction heating in a system of limited permeability is presented. The model applies to underground retorting of oil shale, or to reservoirs containing extremely heavy oils. We assume that heat is introduced at a constant rate into a horizontal fracture which communicates between wells. The radial temperature distribution along the fractured surface is approximated by a step-function. Heat transfer away from the fracture is assumed to be by vertical conduction, and all convection effects are neglected. The model also takes into account the possible temperature dependence of thermal conductivity. A general expression for calculating the growth of the step-function temperature distribution with time is derived. The use of this expression and solutions to the one-dimensional heat equation make it possible to construct isotherms. Expressions for calculating .oil recovery, well spacing and heat efficiency are also given. An example calculation is presented for the conduction heating process in oil shale. Finally, the effect of the heat transfer coefficient between the gas and the fracture boundaries is investigated. INTRODUCTION Thermal recovery processes of oil recovery fall into the four general areas of hot fluid injection, forward combustion, reverse combustion and conduction heating. The first three of* these processes have been rather extensively studied in the past decade from both the experimental and theoretical points of view. As a result, it is possible to make reasonable engineering predictions and analyses of these processes. Little attention has been devoted, however, to the conduction heating process other than to note its possible utility.I To a certain extent, conduction heating cannot be divorced from the other regimes cited above, insofar as these provide the source of heat energy. In the conduction heating process, heat is introduced (either by combustion in the forward or reverse mode or by hot fluid injection) into a small fraction of the total reservoir thickness. This fraction may be either a streak of high permeability or an interwell fracture. Heat penetrates by conduction into the adjacent, less permeable regions of the oil-bearing rock, where the direction of conduction is essentially perpendicular to the streak or fracture. The heated product then drains by gravity or is gas driven to production wells. Conduction heating is probably most applicable to systems containing immobile bitumens such as tar sands and oil shale deposits and perhaps to low-permeability reservoirs containing highly viscous crudes. The mechanism also acts in combination with other thermal processes where fingering or overriding of a bed occurs. It seems probable that in at least one field test, conduction heating of this type was very influential.2 In this presentation we give a first approximation to some of the quantitative aspects of conduction heating. Marx and Langenheim3 treated a similar problem where they focused attention upon the injection interval, which spanned the total reservoir thickness. In their model, conduction heat losses to the bounding media imposed a practical limit on the calculated heated area. In the present study, however, we shall confine the injection interval to a small fraction of the reservoir thickness and assume it has no heat capacity. We therefore direct our attention to regions outside the injection interval into which the conduction of heat is beneficial. In particular, we will endeavor to locate specific isotherms in the media bounding the injection interval. Furthermore, we will construct our model to allow the thermal conductivity to vary arbitrarily with temperature. Thus the model will be applicable to underground retorting of shale where variations in thermal conductivity may be important. THEORY We consider the rock matrix to have no or, at best, a very limited permeability; consequently a

Jan 1, 1965

By G. R. Purdy, J. A. Malcolm

The isothermal dendritic precipitation of y in p CuZnSn is compared with the isothermal formation of Widmanstatten a plates in p CuZn. Although both precipitates are evidently bounded by semicoherent interfaces, the dendritic shape of y evolves through smooth "sinuoidal" shape perturbations, while a-p interfaces tend to be strictly planar, or rnicroscopically faceted. An estimate of the average inter-facial free energy of cube-oriented y in p through the Mullins-Sekerka analysis indicates that it is low (of the order of 50 ergs per sq cm). Interface mication is apparently controlled by volunle dij'usion, and the observed anisotropy in growth probably results from anisotropy of inter facial free energy. Studies of the grain boundary precipitation of y in p indicate that the precipitate can grow in both $ grains, but becomes unstable with respect to the grain with which it shares a mobile semicoherent interface. Facets observed at the tips of Kurdjumov-Sacks-oriented Wid-manstatten a plates correspond to variants of an irrational hahit, near (231)0. Comparison with Hu and Smith's determination of relative interfacial free energies of a-(3 boundaries suggests that this system possesses an extremely deep o cup, which results in an ej'ective low-o zone. The possible effects of such a cup on the stability of a-p interfaces are discussed, a needles, grown during rapid continuous cooling, possess microscopically smooth interfaces, and are characterized by a high degree of' damage in the region of the boundaries. These boundaries, induced to move on tempering at 200"C, become faceted as equilibrium is approached, which seems to indicate that boundary structure and mobility in this system are dependent on the local degvee of departure from equilibrium MULLINS and sekerkal have elucidated the phase boundary stabilizing effect of surface tension. a factor not taken into account in previous treatments of morphological development. Their analysis applies to the isothermal growth of a pure spherical precipitate (planar in the limit of infinite radius) in a slightly supersaturated solution, under conditions of inter-facial local equilibrium and isotropy of interfacial free energy. More recently, several other factors which might tend to stabilize planar interfaces have received attention. These are: i) interface diffusion;4"8 and ii) slow interfacial reaction. cahn7 included a slight anisotropy in interfacial free energy, and showed that it has no stabilizing effect, but forces shape perturbations to reflect the anisotropy. shewmon4 noted that dendritic morphologies are rarely observed in solid-solid systems, and, in particular, postulated that slow interfacial reaction occurs at all boundaries between proeutectoid ferrite and austenite, except those which propagate parallel to {11 l)y planes (for Kurdjumov-Sachs [K-S] related phases). Previously, Aaronson~ had proposed interfacial reaction at the broad faces of Widmanstatten plates, and expected that the lateral motion of high-mobility incoherent ledge edges would produce planar precipitates bounded by law-mobility semi-coherent interfaces. The problem of interfacial reaction during the dif-fusional formation of precipitates has often been ignored, although it is apparent that a small component of chemical reaction must exist at any moving interface." Further, all solutions of the diffusion equations for boundary conditions corresponding to isothermal growth predict infinite growth rate at time zero, so that elements of interfacial reaction would be most easily detected at early times. However, reported deviations from diffusion control are comparatively rare," and the local-equilibrium diffusion-control model appears adequate for the description of many isothermal growth systems.'2"9 Cahn14 has treated the problem of migration of an interface which is able to reach positional energy minima, and concluded that such an interface, if subjected to a high local ther-modynamic "driving force", may migrate normal to itself without the benefit of ledges. As local equi-

Jan 1, 1968

By J. Husson, R. Iffly, M. Gondouin

A systematic variation of well deliverability, as reflected from isochronal back-pressure tests performed at regular intervals, has been observed in some gas condensate wells producing at high rates. The same effects have been obtained using a numerical model of gas and condensate flow which takes into account secondary gasoline deposited in the pore space as a result of pressure reduction, and non - Darcy flow of gas in the vicinity of the wells. Matching calculated values with previous test results has been possible, and future predictions have been obtained. An application of this method to the Hassi Er R'Mel gas-condensate field in Algeria is tentatively shown. INTRODUCTION Flow capacity of gas wells is generally derived from an analysis of back-pressure tests. The empirical equation q = C (?p2)n used by Rawlins and Schellhardtl can be derived rigorously assuming that steady-state radial flow of a dry gas of constant viscosity and compressibility is established during each flow period of the well tests. Furthermore, when Darcy's law applies in the entire flow region, the theory predicts that the exponent n is equal to 1. In low-permeability reservoirs, it was soon discovered that the time required to reach a stabilized flow often exceeded the duration of the flow periods normally available for testing wells. Consequently, transient gas flow had to be considered instead of the steady-state assumption previously used. This led to the isochronal testing procedure established by Cullender2 which has largely replaced conventional back-pressure testing. For dry gas fields, this method yields definite values of C and n equivalent to those of the empirical equation. These values should remain constant for each well as long as the permeability of the formation and the characteristics of the gas (viscosity and compressibility) do not change appreciably. This is the case when reservoir pressure remains -close to the original value and when the formation near the wellbore remains free of plugging. Under those conditions, stabilized flow potential curves of gas wells can be established from a single sequence of isochronal flow and shut-in periods. An analysis of a pressure build-up following a longer production period provides additional data on the transmissivity (k h/ u) of the reservoir, and eventually on the 'drainage radius rd of the well, which can be related to the value of C so that future performance of the well can be predicted using the concepts developed by A. Houpeurt.3 At high flow rates, Darcy's law no longer applies in the vicinity of the wellbore, and inertial effects in the high velocity gas flow introduce additional pressure drops. As a consequence, exponent n of the backpressure tests becomes smaller than 1, and a slight curvature of the log-log plot of ?p2 vs q can be predicted when going from very low to high rates of flow (Elenbaas and Katz).5 The effects of variations of viscosity and compressibility with pressure on the radial flow of dry gas in an infinite reservoir were taken into account by Jenkins and Aronofsky.7 Numerical solutions of the transient flow of an ideal gas in finite radial reservoirs were presented by Bruce, Peaceman, Rachford and Rice.8 In the case of gas condensate wells, however, the presence of gasoline in the pore space as soon as reservoir pressure is reduced below the dewpoint pressure further complicates the interpretation of flow tests so that the prediction of stabilized well performance becomes very difficult. Field observation shows that both C and n derived from isochronal tests vary in time, even when reservoir pressure has not changed appreciably. Such a variation cannot be attributed to any change of the gas characteristics, and must result from the effect of a gasoline saturation on the gas flow.

By H. Bartholomew, L. Bernstein

Experirmental bonds of Ag-In SLID to gold, copper, nickel, Kovar, Dumet, nickel-plated molybdenum, ALL-Pt vrzetallizing on ceramic, and nickel-plated Mo-Ti metallizing on Al2O3 ceramic have been made and exalnined. Metallographic taper sections were made of all bonds for Phase identification. In addition, failuve temperatltres were determined for bonds heated undev shear load. Sowe bonds were subjected to electvon-probe microanalysis. The ternary SLID system Ag-In-Sn was similarly evaluated. Plwtonticrogaphs and electron-probe data are discussed and related to over-all phase diagrams , diffusion effects, and wetting properties of the liquid. The rates of diffusion andor compound formation of gold, silver, and copper in indium and In-Sn liquids are found to descend in that order, as measured by the relatzve thickness of phase layers in the interfaces of bonds made at 200to 400°C. It is concluded that the SLID process enables one to produce bonds which are stable at high temperatures, after having been fabricated at low temperatures, and meet most requirements for application in interconnection, silicon bonding, or hermetic sealing of electronic devices. In a previous publication by one of the authors, the theory and principle of SLID bonding in simple binary systems was discussed. SLID bonding can be defined as a joining process using a preform with a laminated structure: a low-melting material clad on a high-melting core. During the bonding cycle a metallurgical transformation occurs such that the resultant structure can withstand, without reliquefying, temperatures higher than those at which the bond was made. The phases present in the joint interface region are high-melting compounds or, if equilibrium is reached, solid solution. Properties will depend on the phases present, ultimately approaching those of the solid substrate core of the SLID preform. The high-temperature strength of bonds made in these systems was correlated to phase identification in the interfacial bond regions from metallographic cross sections and electron-probe X-ray microanalysis data. When complex electronic components are assembled, multiphase systems result at the interfaces of bond regions. In these ternary and higher-order systems very little diffusion and phase-diagram data is available with which to predict the nature of the interfacia1 region that will result from conventional fabrication processes and subsequent field use of the component. Clarke and Rhines did early work in the field using the Al-Mg-Zn system as a vehicle. Guy and co-workers studied a portion of the Cu-Zn-Ni system and some mathematical4 and general5 aspects of multiphase diffusion. irkald' and coworkerse recently studied diffusion in the Cu-Zn-Sn system. No diffusion studies have been made on ternary systems directly applicable to this investigation but some phase diagrams are available: g-u-n, u-i-n, and CU-i-n. I) DESCRIPTION AND EXPERIMENTAL PROCEDURE The elements Au, Ag, Cu, Ni, In, and Sn are found in alloy systems commonly used in fabricating and assembling electronic components. Reference to the appropriate phase diagrams9 and the previous publication will indicate that the binary systems of any of the two low-melting elements, indium and tin, with any one of the other four higher-melting elements are capable of producing SLID bonds. It is not unreasonable to assume that any ternary or higher-order alloy system containing at least one of the elements gold, silver, copper, or nickel and one or both of the elements indium and tin could be used to produce bonds which are stable at high temperatures, after having been fabricated at low temperatures. Indeed, the liquidus contours and isothermal sections of those phase diagrams available7 do so indicate. The parameters affecting the bond and the equipment used in evaluating the bond were described in an earlier paper.' The current investigation used the

Jan 1, 1967

By J. H. Scaff, W. G. Pfann

The effects of impurities on the electrical properties of silicon are discussed in a companion paper by Messrs. Scaff, Theuerer, and Schumacher.' It was shown that an ingot of silicon which contained boron and phosphorus in certain concentrations consisted partly of p-silicon and partly of n-silicon2 and that the common boundary between these regions was the source of a photo-voltage. These features were ascribed to the segregation of boron and phosphorus during solidification of the ingot. Because of different rates of segregation the first portion of the ingot to freeze contained a molar excess of boron over phosphorus and hence was p-silicon. The last-solidified region contained a molar excess of phosphorus and was n-silicon. This paper is concerned with the microscopic examination of such ingots. The microstructures are rather unusual in certain respects and their study has helped to show how the segregation of minor elements modifies the electrical properties of silicon. The microstructures of ingots prepared from two lots of silicon, designated 1 and 2, will be described. These lots were obtained from the Electro Metallurgical Co. Both contain 99.8+ pct silicon, but they differ in impurity analysis. For each lot will be shown the microstruc-ture of a slowly cooled ingot, for which the time of solidification is 6 min., and that of a rapidly cooled ingot, for which the time of solidification is 2 min. The ingots were prepared from 45 g charges of silicon. When an alloy freezes a cored structure is generally produced because of insufficient diffusion to remove concentration differences established during freezing. As a result of coring the first portion of a crystal to freeze is usually poorer in solute than equilibrium requires, while the last material to solidify is richer. In a columnar grain, growth is principally unidirectional and coring can produce a concentration gradient along the entire grain. By carrying the picture of the coring process from a single grain to an entire ingot in which columnar grains are aligned more or less radially, one can easily see that a composition gradient could be established between the outside and center of the ingot. This, to a considerable extent, occurs during the solidification of a slowly cooled ingot of silicon. Slowly Cooled Ingot In slowly cooled ingots of both lots of silicon, columnar grains which are approximately radial in direction and longest at the top of the ingot enclose a region in which the shapes and align- ment of the grains are considerably less regular. The central region is last to solidify and contains cavities and inclusions. The sketch of Fig 1 illustrates some of these features, as well as others which will be described below. If a polished section of an ingot is etched in a mixture of 2 parts of 20 pct HF and 98 parts of HNO3 the p-n barrier becomes visible. The overall shape of the barrier in a slowly-cooled ingot is roughly oval, as may be seen in Fig 1. The proportion of n-silicon, that is, the region enclosed by the barrier, is considerably greater in ingots of lot 1 than in those of lot 2. A sample about 34 x 1/8 X 1/8 in. was cut from a slowly cooled ingot of lot 1 with its long direction extending from the top of the ingot to the porous region. Thus its upper half was psilicon, its lower half n-silicon. A longitudinal face was polished and etched in the acid mixture. The areas of interest are identified in Fig 2. A band of parallel markings extends across the sample in the columnar region. These striae are roughly parallel to the upper surface of the ingot and cross grain boundaries with only slight deviations. They are quite distinct in the n-silicon,

Jan 1, 1950

By G. Sachs, E. J. Riping

All ferrous alloys can be made brittle by straining at sufficiently low temperatures. However, the changes in mechanical properties for different ferrous materials with decreasing testing temperature do not appear to follow any universal law. In particular, complex effects of testing temperature have been observed if cold worked steels were subjected to tensile tests at low temperatures. EFFECTS OF PRESTRAINING AT A TEMPERATURE ABOVE THE TESTING TEMPERATURE ON THE FRACTURE CHARACTERISTICS‡ A considerable amount of data has been presented by a number of investigators on the fracture characteristics of various cold worked steels.' These data usually relate to a two-step procedure first used by Davidenkov,² consisting of stretching by tension to a certain strain or " prestraining" at room temperature and then completing the tensile test, or "testing" at the temperature of liquid air. On the basis of data of this type made available to date, ferrous alloys can be classified into two groups with respect to their fracture characteristics observed on testing at a low temperature after prestraining at room temperature. Very complex phenomena have been observed for all annealed steels. On the other hand, some observations indicate that steels in certain other conditions represent a fundamentally simpler relation. In considering the effect of prestraining at one temperature on the properties obtained at some lower temperature, it should be expected that any cold work reduces the ductility retained in proportion to the magnitude of the cold work. However, the test data presented to date indicate that only heat treated (quenched and tempered) steels appear to conform to this expectation, according to the very limited test data in Fig 1, presented by McAdam, Geil and Mebs. This series of tests, Fig 1, shows that the retained ductility became smaller the larger the prestrain. However, this decrease is less than the amount of prestrain or, in other words, less than the decrease in ductility at the prestraining temperature. These effects of prestraining are fundamentally identical with those observed by Bridgman3 when a steel was prestrained (in tension) under hydrostatic pressure and then subjected to a regular tension test. It appears, therefore, that the basic effect of prestraining under conditions which yield a higher ductility than the (subsequent) testing procedure, consists of gradually increasing the total ductility of the metal from the initial low value of testing to the higher value of prestraining. On the other hand, all annealed steels, if cold worked by tension at room temperature and then tested at a lower temperature, provided that some ductility is retained, showed a far more complex behavior than that discussed above. This relationship is exemplified by Fig 2, for three pearlitic steels.4,5 These particular steels were selected because of the various shapes of their ductility-prestrain curves. All three steels, and any other investigated so far, suffered a rapid decrease in retained (and consequently also in total) ductility when subjected to small pre-strains. Then, after exceeding a certain prestrain it was generally observed that the ductility recovered.* This rather complex behavior of annealed steels may be tentatively correlated with the presence of stretcher strains at small restrains. Heat treated steels do not exhibit stretcher strains. This fact might possibly explain their simpler prestrain-retained ductility relationship. The destructive effect of these stretcher strains may possibly be associated with the presence of triaxiality, which may occur in any highly non-uniform stress and strain state (and which is retained as residual stress after unloading). Even a small degree of triaxiality may then cause a reduction in ductility, or even embrittlement at a sufficiently low testing temperature. The discussion presented above deals with the effects of cold working at a high temperature on the fracturing

Jan 1, 1950