Search Documents

By B. L. Averbach, E. E. Underwood

The vapor pressure of zinc in equilibrium with solid ß AgZn alloys has been measured by the dew-point method. The thermodynamic activities of silver, and the molar heats of formation have been calculated. Similar measurements have been made for the ternary alloys formed by adding gold to AgZn. An apparent particle size effect has been observed for AgZn filings. The vapor pressure of zinc over filings is 15 to 20 pct higher than over the solid alloys. STATISTICAL methods have been used to inter pret the thermodynamic activities of the components of a solid solution in terms of average equilibrium atomic configurations. In some cases, the atomic arrangements can be measured by X-ray methods, and the results are usually expressed in terms of short range order parameters. Only in the cases of Cu³Au and AgAu have there been sufficient X-ray and thermodynamic data to verify the assumed correlation between the X-ray and the thermodynamic measurements. In Cu³Au the agreement is good; negative deviations from Raoult's law are observed and the number of Cu-Au nearest neighbor pairs predicted on the basis of the thermodynamic treatments agrees quite well with the number of such pairs observed by the X-ray methods. The ß brass alloys present a different set of conditions. The ordering is so rapid in these alloys that the disordered state cannot be retained on quenching. In contrast, the disordered state in CuAu is easily retained on quenching. On heating, the ordered ß brass loses its long range order continuously as the critical temperature is approached; in Cuau the order decreases slightly on heating and then drops discontinuously to zero at the critical temperature. These differences indicate that the short range order configurations in ß brass systems may be of a different character than in Cudu systems. However, X-ray measurements of local order cannot be made in the Cu-Zn alloys because of the similarity in scattering factors. The alloy AgZn is isomorphous with CuZn, however, and recent experiments have indicated that there is a good possibility of observing short range order in this system. Another complication arises in the case of ß AgZn. The disordered body-centered cubic structure exists above 280°C. On quenching from above this temperature an ordered structure of the cesium-chloride type is formed. On slow cooling, however, a complex hexagonal structure, the 3 phase, is produced; and if an ordered quenched alloy is reheated the phase begins to form above 80°C. It is thus difficult to study local order by X-ray methods in single crystals of AgZn since the C phase formed on heating does not necessarily return to a single crystal of the original orientation. This problem has been met, however, by adding a few percent of gold to the AgZn. The gold suppresses the formation of the c

Jan 1, 1952

By O. Katz, A. Spilners, M. Simnad

THE oxidation of titanium has been studied in recent years by a number of investigators.'-W ne of the most important aspects of the reaction of titanium with oxygen, which has been observed by several of the investigators, is the extremely high solubility of oxygen in the metal. A detailed study of the Ti-0 systeml% as shown that the solubility limit of oxygen in a-titanium is approximately 14.5 wt pct 0 from 800" to 1700°C. The unusual oxidation behavior of titanium may be ascribed to this phenomenon, since part of the oxygen uptake enters into solid solution in the metal and only a part is available for scale formation. A more complete study of the kinetics of oxidation of titanium would require information on the influence of oxygen in solution in the metal upon the oxidation rate. Such information would also be of interest in regard to the theory of oxidation of metals. The authors have measured the oxidation rates of oxygen-saturated and oxygen-free titanium between 800" and 1200°C and have found appreciable differences in their rates of oxygen uptake and in the activation energies. The experimental set-up was similar to that described in a previous paper.u The course of oxida-dation was followed continously by attaching the specimen to a sensitive spring balance and observing the extension of the spring with time of oxidation. High purity electrolytic oxygen was used and precautions were taken to purify the gases employed. The specimens were prepared from iodide titanium and were ground on metallographic polishing papers to a fineness of 4/0. The furnace was first evacuated and filled with argon; the specimen was lowered into the furnace, which was then evacuated and filled with oxygen, after the specimen had reached the oxidation temperature in argon. The samples were presaturated with oxygen by means of the following procedure: Each specimen was first heated in oxygen at 1200°C until its increase in weight indicated 13.8 pct by weight uptake of oxygen. The furnace was then immediately evacuated and filled with purified argon five times. The specimen was heated in the argon atmosphere for a period of 72 hr at 1200°C in order to saturate the metal with oxygen by complete absorption of the scale. The temperature was lowered to the oxidation temperature, the furnace was evacuated and filled with oxygen, and the oxidation rate was followed by noting the extension of the spring balance. No oxide film was visible on these specimens at the start of the oxidation experiments. Titanium samples in the oxygen-free as-received condition were also oxidized and their oxidation rates measured. The results are shown in Figs. 1, 2, and 3, which indicate that the initial rates of uptake of oxygen by both the oxygen-saturated and oxygen-free specimens are parabolic at these temperatures. The rate of uptake of oxygen is, however, appreciably lower

Jan 1, 1956

By T. J. Fabiniak, R. A. Dodd, R. Balow

ALTHOUGH the (111) slip direction in pure bcc metals is well established, the information on operative slip planes is less unambiguously interpreted. So far, (110) {112), and (123) slip planes have been identified, but it is not certain whether glide on (112) and (123) really occurs or if it is composite slip on non-parallel (110) planes. The second of these possibilities is supported by the work of Chen and Maddin on niobium and molybdenum, and a subsequent analysis by these same workers of slip in bcc metals generally.3 The alternative possibility is exemplified by the work of Opinsky and smoluchowsky4 who concluded that slip in Fe-Si crystals can occur on any one of the systems {110}(111), {112}(111), and {123)(111), depending on which system the resolved shear stress is highest. Allen et alS5 also found that glide in ar iron could occur on any of these three systems, the operative system being determined principally by orientation. By an analysis of crystal rotation, slip lines, and X-ray asterism Harris6 concluded that niobium also deforms on these same systems, but if one of these glide planes does not coincide with the plane of maximum resolved shear stress, composite slip on nonparallel (110) planes may occur giving a macroscopic high indices slip plane. Earlier work on iron by Vogel and Brick reached the same conclusion.7 The analysis of slip in bcc metals is made more difficult by the fact that the slip lines may be quite wavy. In fact, the generality of wavy slip lines suggests that screw dislocations slip readily from one plane to another in the (111) zone ("pencil glide") although, as noted, it is not certain whether planes other than (110) really contribute to the slip. If planes of higher indices than {110} do operate, there is a possibility they may do so more readily at higher temperature Argon and Maloof9 observed {100}{211}(111) slip in tungsten single crystals plastically strained at low temperatures, but the results were interpreted in terms of an orientation-dependence rather than temperature-dependence. Therefore, at the present time corroborative evidence for the operation of higher indices slip planes at higher temperatures is lacking. The present results were obtained during the course of an investigation into the effect of cathode and anode surface crystallography on the prebreakdown currents of vacuum insulated devices. In the experiment of particular interest, the 1/8-in.-diam anode and the in.-diam cathode were tungsten crystals (total impurities -230 ppm) with (110) and (100) faces respectively. The faces were electrolytically planed and examined for initial perfection by plastic/carbon replicas and a study of Kikuchi lines in reflection electron diffraction patterns. They were aligned precisely parallel in an insulating holder incorporated into the electron microscope, the measured microscope vacuum being 2 x 10-5 torr, and the electrode spacing 0.01524 cm. The anode structure shown in Fig. 1 was obtained

Jan 1, 1970

By D. B. Masson

THE martensitic transformations occurring in ,B AgCd as a result of cold working at room temp.. a-ture and cooling below room ten1erature have been reported by Masson and Barrett.1 These authors found that simple cooling to 127°K caused body-cen-tered-cubic AgCd containing 53.0 at. pct Ag to transform to an orthorhombic structure, while mechanical deformation at room temperature was found to induce a hexagonal structure. Furthermore, they observed that the temperature at which martensite first appeared on cooling, Ms, and that at which the transformation was complete, MI, as well as the corresponding temperatures for the reversion on heating, As and Af, could be ascertained to ± 1°K, although they report these temperatures only for the alloy containing 53.0 at. pct Ag (51.96 wt pct). In the work reported here the temperature range of the transformation on cooling was studied as a function of composition, and further consideration was given to the relationship between the original bcc structure and the transformation-induced hexagonal and orthorhomic structures. EXPERIMENTAL PROCEDURE All samples studied were in the form of annealed 300-mesh powder and were prepared from the constituent metals in the manner described previously.1 The compositions in weight and atomic pct are listed in Columns 1 and 2 of Table I. Method of determination of transformation temperature was the same as utilized previously1—measurement of the intensity of X-rays diffracted by the transformation product. A diagram of the low-temperature sample mount is shown in Fig. 1. This mount was made to fit a GE model XRD-3 X-ray diffraction unit. The powder sample was varnished to a flat surface on a copper sample holder at A. This sample holder was soldered to a brass rod, B, which was in turn soldered to a second copper rod, C. Rod C could be cooled to 78°K by inserting it into a reservoir of liquid nitrogen, D. A heater coil of nichrome wire was wound at E on the sample holder, and by varying the current through the heater a thermal gradient could be maintained along brass rod B. Sample temperatures from 78°K up could be attained and held as long as needed. The sample holder and nitrogen reservoir were insulated by Styrofoam, F, and the sample itself was protected by two radiation shields, G. The X-ray beam entered and left the sample chamber through windoys in the supporting container at H and I. Sample temperatures were measured by a calibrated copper-constantan thermocouple varnished to the sample holder just out of the beam at A. The low-temperature structure had been found to possess orthorhombic symmetry1 and the expected positions of the diffraction maxima were known. Therefore the sample was aligned in the X-ray beam and the Geiger counter of the spectrometer set to receive the most intense orthorhombic reflection without an adjacent interfering cubic reflection. This

Jan 1, 1961

The San Manuel district of Arizona was first prospected prior to the Civil War, but there was little or no production until 1881. Small operators tried to develop ore bodies from time to time after that without success. Then, in 1917, a drilling program was carried out; but it did not indicate a copper content of interest. Finally, in the 1940s, the U. S. Geological Survey drilled the property and obtained indications of a mineralized area. At that time, Magma Copper and its principal owner, Newrnont Mining Corporation, drilled many deep holes through the gravels and conglomerates and in 1948 proved an ore reserve of 367 million tons of 0.785% copper sulfide ore. Underground exploration and development were started in early 1948, and in 1953 design and construction of the surface facilities commenced. By the end of 1955 plant construction was completed. The ore deposit of disseminated pyrite, chalcopyrite, chalcocite, molybdenite, silver, and gold is in quartz monzonite porphyry gangue. Mine production, which is entirely underground, is by full-gravity block-caving. Initially, ore mined at a rate of 36,000 tpd was hoisted through two identical shafts. From the 5,000 ton coarse ore bins located at the collar of each shaft, the ore was hauled by a shuttle service rail- road in 100-ton bottom-dump rail cars a distance of seven miles to the rail bin. Fragmentation from block-caving supplemented by underground grizzlies at the loading stations controlled the oversize material to give a feed size acceptable to the two 7 ft standard Syrnons crushers. During operation, however, it became evident that a large amount of secondary breaking in the grizzlies was necessary to produce a suitable feed for the standard crushers. The decision was then made to install primary gyratory crushers on the surface adjacent to the shaft site ore bins. Under each 5,000-ton coarse ore bin, an 8ft by 20 ft (2.44 m by 6. 1 m) apron feeder transfers the ore to a 13 ft 6 in. by 10 ft (4. 1 m by 3. 05 m) grizzly set at 6 in. (152 mm) and sloped at 45 degrees. About 65% of the ore passes the grizzly and thus bypasses the 42 in. by 65 in. (1.07 m by 1. 65 m) Allis -Chalmers gyratory equipped with a Hydroset mechanism and having an open side setting of 5 ½ in. (140 mm). Grizzly undersize and crushed ore drop onto a 6 ft by 30 ft (1. 83 m by 9. 14 m) variable- speed apron feeder for transfer to a 54 in. by 90 ft 5 in. (1.37 m by 27.6 m) inclined conveyor equipped with a tramp iron detector. Indication of tramp iron automatically stops the conveyor and both apron feeders. When the iron is removed from the belt by the operator,

Jan 1, 1978

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

It is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investi-: gators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson's1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by - experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from IIoo° to 17oo°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxida- tion of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous clays burned ' to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,= the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery0 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the clay, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

It is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investi-: gators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson's1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by - experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from IIoo° to 17oo°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxida- tion of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous clays burned ' to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,= the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery0 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the clay, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

By Ferit Gurses

Extensive coal and lignite deposits exist in Turkey. Bituminous coal is the nation's principal mineral resource; important not only as fuel for the industrial development of the country, but also as a means of obtaining foreign exchange. Of the electrical power generated during 1939, 82.8 per cent was derived from coal.' It is anticipated that the lignite deposits will be one of the major sources of power for the electrification of the country. Bituminous Coal The locations of the four principal bituminous-coal2 basins are indicated on Fig. 1. The Eregli-Zonguldak basin lies on the Black Sea northwest of Ankara; the Canakkale basin lies near the junction of the Dardannelles; the Trakya basin is in European Turkey northwest of the Bosphorus and the Erzurum basin lies far to the east. The Eregli-Zonguldak basin is the most important of the four. This coal basin was discovered in 1829 but did not arouse interest until 1848; up to 1865, its annual production had not exceeded 50,000 metric tons. In 1865, during the Sultanate, working of coal mines was started by the Navy department, and the annual production was 61,145 metric tons. In 1908, the Minister of Commerce and Agriculture was authorized to develop the whole coal basin. Production reached 264,397 metric tons in 1910, and during 1915-1922, preceding the revolution, the total produc- tion of the basin was' 2,676,043, or an average of 334,000 metric tons annually. The period of national revolution that followed was marked by a steady increase in coal production in Turkey, although world production decreased, because of the crisis of 1929-1932, about 52 per cent. ARea and Geology of the Coal Basin The geology of the Eregli-Zonguldak area is not yet completely known. The basin begins -at Gungazi, to the west of Eregli, and extends to Sogutozu, a distance of about 106 miles. The coal beds, however, appear only in places and the overlying Cretaceous strata hide them elsewhere. This area includes the most important centers, such as Kandilli, Alacaagzi, Teflenli, Kozlu, Gelik (see Fig. 2). The geological sequence of the district is correlated with the Cretaceous of the Balkans; which is, in turn, a prolongation of the Alpine zone. Geological surveys made by G. Ralli, R. Zeiller and P. Arni3 show that the Eregli-Zonguldak formations fall into three natural divisions. Series a, The Alacaagzi in the district of that name (Fig. 2), is of the Culm stage. The strata strike generally east-west and dip about 30" south. This series appears also around Kandilli and Camli, with a steeper angle of dip, but the deposits there lack regularity. The Alacaagzi stage appears also farther east, to the south of Kozlu and Gelik. The Alacaagzi series contains 15 seams of an average thickness of 2 ft. of good coal. Series b, the Kozlu, best represented in Zonguldak, Kilimli, Catalagzi, and between

Jan 1, 1944

By P. B. Crawford, W. L. Huskey

A study has been made to determine the effects of random vertical fractures existing in a reservoir matrix on the effective matrix properties and producing characteristics of a well. The study indicated that short vertical fractures may distort the isopotentials by 1 percent in the vicinity of the fracture. A correlation was developed which showed the effect of fracture density on the producing capacity of a well. The correlation indicated that fracture shape had little effect on producing capacity, but that total fracture length was closely correlated with the producing capacity. Effective values of reservoir permeability were found to correlate closely with fracture density when measured parallel to the direction of flow. INTRODUCTION In reviewing the petroleum literature, it is found that in most analytical solutions of hydrocarbon reservoir behavior the assumption is made that the rock is uniform throughout although core analysis and well logging surveys indicate that substantially all reservoirs are heterogeneous and some are fractured. Only in recent years have investigators studied the effects of reservoir hetrogeneity. Russell1 discussed the effect of fractures in reservoirs. The literature indicates that fractures greatly affect the exploitation of man reservoirs. This is described by Elkins and Skov2 and Little-field et al. 3 Several types of reservoir heterogeneity have been studied by unsteady-state methods. In 1959, Landrum et al. 4 showed that transient phenomena in hydrocarbon reservoirs could be studied by thermal models. pickering5 studied the flow of heat in stratified linear reservoirs consisting of plates of different metals separated by sheets of rubber which were suddenly exposed to a low-temperature source at one end. Cotman6 studied both laterally and vertically heterogeneous thermal model reservoirs with special reference to cross flow. Another type of reservoir heterogeneity involves the presence of highly permeable, circular lenses around or near the wellbore which was studied by Miesch7 using a thermal and a steady-state model. Many studies have been made of the effects of induced hydraulic fractures on well performance. 8-10 Work regarding vertical fractures that exist initially in the reservoir was reported by Givens, et al.11 Since there appears to be little published work on the importance and influence on reservoir performance of fractures that exist out in the rock matrix, this study was conducted to determine the effects of vertical fractures on pressure distribution, producing capacity and the effective permeability of the reservoir rock. The analogy between the flow of electrical current through a conducting body and the flow of fluid in a porous medium provides a convenient method of studying various aspects of petroleum reservoirs. For electrical radial steady-state flow,12 For steady-state fluid flow, With the above analogy, it is only necessary to establish the ratio of the values of the electrical units in terms of the corresponding flow units to make the analogy quantitative. The ratios are shown below.

By Ferit Gurses

Extensive coal and lignite deposits exist in Turkey. Bituminous coal is the nation's principal mineral resource; important not only as fuel for the industrial development of the country, but also as a means of obtaining foreign exchange. Of the electrical power generated during 1939, 82.8 per cent was derived from coal.' It is anticipated that the lignite deposits will be one of the major sources of power for the electrification of the country. Bituminous Coal The locations of the four principal bituminous-coal2 basins are indicated on Fig. 1. The Eregli-Zonguldak basin lies on the Black Sea northwest of Ankara; the Canakkale basin lies near the junction of the Dardannelles; the Trakya basin is in European Turkey northwest of the Bosphorus and the Erzurum basin lies far to the east. The Eregli-Zonguldak basin is the most important of the four. This coal basin was discovered in 1829 but did not arouse interest until 1848; up to 1865, its annual production had not exceeded 50,000 metric tons. In 1865, during the Sultanate, working of coal mines was started by the Navy department, and the annual production was 61,145 metric tons. In 1908, the Minister of Commerce and Agriculture was authorized to develop the whole coal basin. Production reached 264,397 metric tons in 1910, and during 1915-1922, preceding the revolution, the total produc- tion of the basin was' 2,676,043, or an average of 334,000 metric tons annually. The period of national revolution that followed was marked by a steady increase in coal production in Turkey, although world production decreased, because of the crisis of 1929-1932, about 52 per cent. ARea and Geology of the Coal Basin The geology of the Eregli-Zonguldak area is not yet completely known. The basin begins -at Gungazi, to the west of Eregli, and extends to Sogutozu, a distance of about 106 miles. The coal beds, however, appear only in places and the overlying Cretaceous strata hide them elsewhere. This area includes the most important centers, such as Kandilli, Alacaagzi, Teflenli, Kozlu, Gelik (see Fig. 2). The geological sequence of the district is correlated with the Cretaceous of the Balkans; which is, in turn, a prolongation of the Alpine zone. Geological surveys made by G. Ralli, R. Zeiller and P. Arni3 show that the Eregli-Zonguldak formations fall into three natural divisions. Series a, The Alacaagzi in the district of that name (Fig. 2), is of the Culm stage. The strata strike generally east-west and dip about 30" south. This series appears also around Kandilli and Camli, with a steeper angle of dip, but the deposits there lack regularity. The Alacaagzi stage appears also farther east, to the south of Kozlu and Gelik. The Alacaagzi series contains 15 seams of an average thickness of 2 ft. of good coal. Series b, the Kozlu, best represented in Zonguldak, Kilimli, Catalagzi, and between

Jan 1, 1944

By Louis A. Panek

THE purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fentress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal field exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The maximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repIesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: [Safe R = (rl 47r2n2r _ 7r2n2r~r~ \4/ gg in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sect.]

Jan 1, 1947

By H. R. Nelson, Martin S. Maier

The diffusion of metals plays an important role in many metallurgical processes,lJ as, for example, the formation of alloys by the annealing of mixed powders, the homogenization of segregated alloys, and the carburization of steel. Other equally important phenomena, such as recrystalli-zation and creep, are based on the movement of like atoms. Although much is known concerning the effects of diffusion in metals, very little is known concerning the details of the physical processes involved. 1,3-5 The data that should give most information concerning the processes involved in diffusion are those on the diffusion of like atoms—self-diffusion. Very little is known concerning the rates of self-diffusion of metals because before the discovery of artificial radioactivity in 1934 there was no means of detecting the movement of the diffusing atoms through the solvent metal except in the elements possessing natural radioactive isotopes—lead, thallium and bismuth. Using the induced radioactivity of the element as an indicator, atoms can now be "tagged" so that the rate of diffusion of the radioactive isotopes of an element (tagged atoms) into the stable isotopes of the same element can be measured. As the radioactive and stable isotopes of an element differ only in nuclear structure, it is quite certain that all isotopes of an element diffuse at the same rate. Two techniques have been used to measure self-diffusion. In one, a thin layer of radioactive metal is deposited on the face of the solvent metal, and the decrease in the surface activity as the radioactive atoms diffuse into the solvent metal is measured. This method has been used to determine the coefficients of self-diffusion of lead6-l0 and bismuth10 using natural radioactive isotopes, and of gold1' and copper12 using artificial radioactive isotopes. In the other technique a thin layer of the radioactive metal is deposited oil one face of the solvent metal, and after diffusion has occurred the specimen is cut in thin sections to obtain the concentration-penetration curve. This method has been used to determine the coefficients of self-diffusion of gold,13 zinc,14-l6 silver," and copper.17 The second method was used for the work described in this paper. Materials The coefficients of self-diffusion were determined in two grades of polycrystalline copper and in single crystals of copper. Commercial OFHC copper was used in the form of disks I in. in diameter by % in. thick. Samples of high-purity copper described by Phillips and Skinnerl9 were supplied through the courtesy of the American Smelting and Refining Co. The high-purity copper rod was used without remelting by cross-rolling to a thickness of 0.075 in., from which disks 7/8 in. in diameter were cut. A good grade of bus-bar copper was used to make the single crystals.

Jan 1, 1942

By Martin S. Maier, H. R. Nelson

The diffusion of metals plays an important role in many metallurgical processes,lJ as, for example, the formation of alloys by the annealing of mixed powders, the homogenization of segregated alloys, and the carburization of steel. Other equally important phenomena, such as recrystalli-zation and creep, are based on the movement of like atoms. Although much is known concerning the effects of diffusion in metals, very little is known concerning the details of the physical processes involved. 1,3-5 The data that should give most information concerning the processes involved in diffusion are those on the diffusion of like atoms—self-diffusion. Very little is known concerning the rates of self-diffusion of metals because before the discovery of artificial radioactivity in 1934 there was no means of detecting the movement of the diffusing atoms through the solvent metal except in the elements possessing natural radioactive isotopes—lead, thallium and bismuth. Using the induced radioactivity of the element as an indicator, atoms can now be "tagged" so that the rate of diffusion of the radioactive isotopes of an element (tagged atoms) into the stable isotopes of the same element can be measured. As the radioactive and stable isotopes of an element differ only in nuclear structure, it is quite certain that all isotopes of an element diffuse at the same rate. Two techniques have been used to measure self-diffusion. In one, a thin layer of radioactive metal is deposited on the face of the solvent metal, and the decrease in the surface activity as the radioactive atoms diffuse into the solvent metal is measured. This method has been used to determine the coefficients of self-diffusion of lead6-l0 and bismuth10 using natural radioactive isotopes, and of gold1' and copper12 using artificial radioactive isotopes. In the other technique a thin layer of the radioactive metal is deposited oil one face of the solvent metal, and after diffusion has occurred the specimen is cut in thin sections to obtain the concentration-penetration curve. This method has been used to determine the coefficients of self-diffusion of gold,13 zinc,14-l6 silver," and copper.17 The second method was used for the work described in this paper. Materials The coefficients of self-diffusion were determined in two grades of polycrystalline copper and in single crystals of copper. Commercial OFHC copper was used in the form of disks I in. in diameter by % in. thick. Samples of high-purity copper described by Phillips and Skinnerl9 were supplied through the courtesy of the American Smelting and Refining Co. The high-purity copper rod was used without remelting by cross-rolling to a thickness of 0.075 in., from which disks 7/8 in. in diameter were cut. A good grade of bus-bar copper was used to make the single crystals.

Jan 1, 1942

By N. K. Chen, R. Maddin

Columbium single crystals were deformed in tension and compression. Reorientation by X-rays and stereographic projections of slip traces indicate that plane of slip may be considered as (110). The plastic behavior is shown to be quite similar to the deformation of molybdenum single crystals. STUDIES on the crystallography of the deformation process in body-centered cubic metals have been renewed recently with investigations of iron single crystals1-" and molybdenum single crystals.4 It is now apparent that too many exceptions to the rationalization based upon the ratio of absolute testing temperature to absolute melting point by Andrade5 exist to permit more serious discussion of this type of analysis. The considerations of resolved shear stress utilizing only planes of the type {ll0}, {112), and {123)³,6 permit analysis of the deformation only on the basis of those three types of planes. The suggestions made by Elam7 and by Greninger8 in which the slip process is envisioned as a composite slip on two nonparallel {110) planes can be illustrated schematically in Fig. 1. It may be seen that an unresolved trace on any plane containing a <111> direction may be accomplished by varying the number of atoms participating in the composite process. By further varying the number of atoms in each plane but keeping the ratio of participating atoms constant, jogs could be obtained in the traces and hence wavy slip lines could be produced. Vogel and Brick&apos; studied the behavior of a iron single crystals in which they suggest that the plane of glide is "non-crystallographic" and may be predicted from the intersection between the great circle joining the slip direction and specimen axis with the great circle whose zone axis is the slip direction. In a more recent investigation on iron single crystals, Steijn and Brick" suggest that the slip mechanism may be considered as made up of a type of composite slip occurring on {110} and {112} planes. Evidence for a possible composite nature of the slip process has been presented for the case of molybdenum in the form of analysis of asterism and specimen axis rotation." Definite proof of a composite slip process must, however, await good electron microscopic resolution of the individual traces making up the unresolved optical trace used in determining the acting slip plane. The present investigation was undertaken to study the behavior of columbium single crystals not only in tension but also in compression since the specimen axis migration should indicate the plane or planes of glide in the same manner that the specimen axis migration in tension indicates the direction of glide. The orientations of eleven crystals investigated are shown in Fig. 2. Specific orientations are missing (those in the vicinity of [Ill] and [001] and consequently the effect of orientation on the crystallography of deformation could not be considered. Experimental Procedure The 1/8 in. rods (7 in. long) were subjected to an axial tension in vacuo while at temperatures in the vicinity of 2000°C for 2 to 4 hr. This treatment resulted in large cylindrical grains (about ½ in. long) occupying the entire cross section. A number of these rods were used for the tension studies by observing the behavior of the individual grains. For the compression studies, single crystals approximately % in. long by 1/8 in. in diameter were cut from the rods; the ends were ground parallel. All specimens were polished electrolytically in a solution of 15 cc HF(48 pct) and 85 cc H2SO4 (concentrated) using a platinum cathode, a current density of 0.04 amp per sq cm and a temperature between 25" and 60°C.10 Orientations were obtained using a Laue back-reflection method (3 cm film to specimen distance) with a ½ mm collimator 9 cm long. For the compression specimens, a reference mark was scratched on one of the compression sur-

Jan 1, 1954

By T. H. Janes

NATURAL abrasives of some type are found in all countries of the world. In order of their hardness the principal natural abrasives are diamond, corundum, emery, and garnet, which are termed high grade, and the various forms of silica, including pumice, pumicite, ground feldspar, china clay and, most important, sandstone. The properties qualifying materials for use as abrasives are hardness, toughness, grain shape and size, character of fracture, and purity or uniformity. For manufacture of bonded grain abrasives such as grinding wheels, the stability of the abrasive and its bonding characteristics are also important. No single property is paramount for all uses. Extreme hardness and toughness are needed for some applications, as in diamonds for drill bits, while for other purposes the capacity of the abrasive to break down slowly under use and to develop fresh cutting edges is of greatest importance, as with garnet for sandpaper. In dentifrices, soaps, and metal polishes, of course, hardness and toughness are objectionable. First among the natural abrasives, industrial diamonds are essentially of three types: l—bort, which includes off-color, flawed, or broken fragments unsuitable for gems; 2—carbonado, or black diamond, a very hard and extremely tough aggregate of very small diamond crystals; and 3—ballas, a very hard, tough globular mass of diamond crystals radiating from a common center. Bort comes from all diamond-producing centers, carbonados only from Brazil, and ballas chiefly from Brazil, although a few of this last group come from South Africa. By far the largest producer of industrial diamonds is the Belgian Congo; the Gold Coast, Angola, the Union of South Africa, and Sierra Leone supply most of the remainder. There is no production in Canada, which imports $6 to $9 million worth of industrial diamonds annually. Industrial diamonds find innumerable uses in modern industry. They are used for diamond drill bits for the mining industry; in diamond dies for wire drawing; in diamond-tipped tools for truing abrasive wheels and for turning and boring hard rubber, fibers, and plastics; and in diamond-toothed saws for sawing stone, glass, and metals. High-speed tool steels, cemented carbides, and other hard, dense alloys can be cut, sharpened, or shaped efficiently only with diamond-tipped tools and diamond grinding wheels. .. Second only to the diamond in hardness is corundum, an impure form of the ruby and sapphire gems consisting of alumina and oxygen (Al²O³) with impurities such as silica and ferric oxide. Corundum generally crystallizes from magmas rich in alumina and deficient in silica, as in the nepheline syenites of eastern Ontario. Grain corundum is used in the manufacture of grinding wheels; very coarse grain is used in snagging wheels. Both types of wheels are employed in the metal trades, where the hardness of corundum, coupled with its characteristic fracturing into sharp cutting edges, makes it an ideal cutting tool. The finest corundum (flour grades) is used for fine grinding of glass and high-precision lenses. From 1900 to 1921 Canada was the world&apos;s leading producer of corundum. Following this period the deposits located in northern Transvaal of the Union of South Africa supplied more and more of the world&apos;s requirements, and since 1940 South Africa has provided almost the entire output, which has ranged between 2500 to 7000 tons a year during the last decade. Minor amounts have also been produced in Mozambique, India, and Nyassaland. Opportunities for Mining Corundum Corundum deposits in southeastern Ontario are of three types, which may be described as follows: 1—Scattered, irregularly-shaped deposits of coarse-grained corundum which could be mined by means of small pits. About 10 groups of such deposits are known. Although the tonnage of individual deposits of this type is not great, it has been estimated that several years&apos; ore supply is available for a small tonnage operation. Deposits average about 9 pct corundum. 2—Large irregular deposits of coarse-grained corundum which would require mining by adit with possibly a scavenger operation on the remains of former surface deposits. The Craigmont deposit of this type produced about 20,000 tons of corundum concentrate during operations between 1900 and 1913. Most of the readily available surface ore was removed by operators during that time. Reserves of ore above road level have been estimated to average 7 pct corundum, but none of the so-called reserves have been blocked out, or even indicated, by diamond drilling. From 1944 to 1946, 2025 tons of

Jan 1, 1955

By Brian F. Dyson

The surface tensions at 1550°C of some Fe-S alloys (in the range 0.008 to 0.052 wt pct S), Fe-Sn alloys (0.31 to 48.4 wt pct Sn), Fe-P alloys (0.038 to 2.38 wt pct P), Fe-Cu alloys (2.15 to 22.8 wt pct Cu), and Fe-1 pct C-S alloys (0.005 to 0.076 wt pct S) along with the surface tension of the base iron have been measured by the sessile-drop method. A mean value of 1754 dynes per cm was found for the surface tension of the base iron. Sulfur was found to be highly surface-active, the surface-tension results being in quantitative agreement with existing data. Tin and copper were found to be less surface-active than sulfur while phosphoms was completely nonsurface-active. The surface tensions of Fe-1 pct C-S alloys were found to be lower than those of the Fe-S alloys containing the same sulfur content. This was shown to be a mmzifestation of the increase in the thermodynamic activity of suZfur by carbon. It is only in recent years that attempts have been made to measure the surface tension of liquid iron of known high purity.1-3 Earlier measurements4-7 were made on liquid iron containing variable amounts of what are now known to be surface -active solutes. The exact value of the surface tension of liquid iron is still, however, open to some doubt. Halden and Kingery&apos; reported a value of 1720k 34 dynes per cm at 1570°C, Kozakevitch and Urbain8 gave 1790k 25 dynes per cm at 1550°C, while Van-Tszin-Tan et al. obtained a value of 1865k 37 dynes per cm at 1550°C. The first systematic investigation into the effect of controlled solute additions on the surface tension of iron was made by Halden and Kingery.&apos; They showed that sulfur and oxygen were highly surface-active, whereas nitrogen was only slightly active, and carbon inactive. A subsequent investigation by Kingery indicated that two other group-6B elements, selenium and tellurium, were also surface-active. This highly surface-active nature of sulfur and oxygen has recently been substantiated by Kozakevitch and Urbainla and Van-Tszin-Tan et al. l1 Kozakevitch and Urbainl2 have also conducted an experimental survey of the effects of a number of metals on the surface tension of liquid iron. Their surface-active nature was, in all cases, less than that of the group 6B elements. The present investigation was undertaken to study in more detail the surface tensions of dilute Fe-S alloys and to measure the surface tensions of binary alloys of iron containing phosphorus, copper, and tin. The effect of sulfur additions on the surface tension of Fe-1 pct C alloys was also determined. EXPERIMENTAL PROCEDURE The sessile-drop method was employed in the present investigation. An apparatus was built similar in principle to that described by Humenik and Kingery.lS It consisted of a horizontal silica tube, which could be evacuated to pressures less than 10-5 torr, with its central portion surrounded by a water jacket within which was a high-frequency coil. This generated heat in a tantalum susceptor placed inside the silica tube, which in turn radiated heat to the specimen mounted on a recrystallized alumina plaque. Temperatures were measured by an optical pyrometer and photographs of the molten drop were taken on a fixed-focus plate camera giving a magnification of X2. Surface-tension values were determined from the resultant drop using the method described by Baes and Kellogg.l4 The high vapor pressure of molten iron made it necessary to conduct all the experiments under a 1/4 atm of argon (greater than 99.995 pct purity). The analysis of the base iron used in the investigation is given in Table I. Each sample was approximately 3 g in weight and had a hemispherical base to ensure a uniform advancing contact angle on melting. The iron alloys were prepared individually in the sessile-drop apparatus by drilling a hole in the top of each sample and adding the required amount of solute, the drops being analyzed after the experiment. This method of preparation had the advantage of ensuring a consistent minimal contamination by oxygen due to refractory attack and also allowed surface tension to be measured at the same time. Every precaution was taken to ensure that the specimen was not contaminated by grease when it was introduced into the apparatus, the samples being cleaned in acid, dried in alcohol, and rinsed in petroleum ether. All handling was done with tweezers. Once the specimen had been placed inside the susceptor, the furnace was evacuated and the Sample leveled. The furnace was then degassed at approximately 1000"C before the argon was introduced. In every case the surface tension was determined at 1550" C.

Jan 1, 1963

By A. M. Gaudin, J. G. Morrow

FLOTATION requires the existence of a definite contact angle. This contact angle, the surface tension of the solution, and adsorption at the solid-fluid interface are quantitatively related. Adsorption of dodecylammonium acetate on hematite was measured for a wide range of concentrations of reagent in solution. Similar measurements for quartz have already been made. Contact angle measurements were then made on polished surfaces of hematite and of quartz immersed in aqueous dodecylammonium acetate solutions, and a functional relationship was sought between adsorption density at the mineral-solution interface and the contact angle. Finally, the surface tension of the aqueous amine acetate solutions was measured. These data were combined to give an evaluation of the work of adhesion for the three-phase system. Specular hematite was crushed and then ground dry in a laboratory porcelain mill, with flint pebbles, to pass a 200-mesh screen. The ground product was sized in a Haultain infrasizer, and one of the granular sizes (cone No. 3) was used in all adsorption tests. A hand magnet was used to remove magnetite and abraded iron. Quartz was removed in a Frantz isodynamic magnetic separator. The purified hematite was leached in aqua regia, washed with distilled water until the washings appeared free of electrolyte by conductance measurement, dried in a low-temperature oven, and stored in a pyrex container. The specific surface of the closely sized hematite was determined by the krypton gas adsorption method.&apos; Three measurements gave an average value of 1350 sq cm per g. Chemical analysis showed Fe -69.37 pct, insol = 0.72 pct. The quartz used in the flotation tests had been prepared by Chang" for an earlier investigation. Demineralized distilled water was used for all test solutions. Dissolved salt content was of the order of 0.03 ppm, expressed in terms of sodium chloride, as estimated from conductance measurements. Dodecylammonium acetate was obtained from Armour & CO. in two forms, the unmarked compound and a preparation marked by carbon 14 in the hydrocarbon chain of the aminium ion. Specific activity of the active salt was 0.134 millicurie per g. The important physico-chemical constants for the primary amine salt have been reviewed by de Bruyn. The calculated effect of hydrolysis of amine salt on pH of aqueous solutions and the effect of pH on the distribution ratio of the alkylammonium ion to free amine are of particular interest. All other chemicals used in this investigation were of analytical reagent grade. A column method&apos; was used for adsorption work. Attainment of equilibrium distribution in the adsorption column depends on the solid-solution contact time, hence upon the volume of solution passed. It was assumed that contact time required for equilibrium would be a maximum for the lowest reagent concentrations. On this premise it was demonstrated experimentally that the passage of 500 ml of solution through the mineral bed was adequate. An aliquot (1 to 5 cc) of the solution to be analyzed was transferred to a small pyrex cup and allowed to evaporate to dryness at room temperature; 4 or 5 mg of unmarked amine acetate were added to the dried sample and the cup and its contents were transferred to the combustion system for analysis. Evaporation at room temperature must be emphasized, as even slightly elevated temperatures result in loss of reagent. A laboratory model G Beckman pH meter equipped with a glass electrode was used to measure pH of amine acetate solutions. The technique of internal gas counting of radioactive carbon dioxide in a Geiger-Muller counter was used. Developed originally by Brown and Miller,- his method was adapted to the analysis of carbon-14 marked flotation reagents by Chang, de Bruyn, and Bloecher. nalytica1 method and procedures have been described in detail by Bloecher.&apos; Contact angles were measured by the captive-bubble technique." The mineral specimens were carefully selected to avoid cracks and inclusions of other minerals. All specimens were mounted in plastic and polished to produce a smooth surface. The final polishing and contact-angle measuring

Jan 1, 1955

By Clarence Zener

It is customary to regard the stress-strain relation as consisting of two parts, thc elastic region and the plastic region. The essential attribute of the plastic region is the presence of a permanent set, which remains upon removal of all stresses. The essential attribute of the elastic region is the absence of such a permanent set. Absence of a permanent set does not imply a linear relation between stress and strain, nor even a single valued relation. In fact, in no real metal is stress a single valued function of strain in the elastic region. The property of a solid in virtue of which stress and strain are not uniquely related in the elastic range will be called "anelasticity." The purpose of the present article is to review and correlate the past work upon the anelasticity of metals. The following paper by W. A. West124 describes investigations upon anelastic properties of iron. Many manifestations of anelasticity have been observed, the first as early as 1835 by Weber.l,2 In his experiments Weber subjected a specimen to a constant load (or deformation) for a given time, and then suddenly removed the load. He observed that most of the deformation suddenly disappeared, but that there remained a residual deformation, which disappeared only gradually with time, as is illustrated in Fig. I. The occurrence of a residual deformation which only gradually disappeared, Weber called the elastic after-effect (Elastische Nackwir-kung). An extensive review of the early work upon elastic after-effects has been given by Auerbach.3 Another manifestation of anelasticity is the dependence of the elastic constants---e.g., Young&apos;s modulus— upon the method of measurement. Thus, if dynamic methods are used, the measured value will depend upon the frequency of oscillation. Still another manifestation is dissipation of energy attending vibration, called damping or internal friction. One objective. of metallurgical science is the understanding of the plastic and fracture properties of metals in terms of their microstructure. Through such an understanding will come the ability to design microstructure to give the desired mechanical properties. A study of anelasticity will furnish an invaluable aid in the attainment of this objective. Such studies, when properly guided, yield information regarding the relation between stress and strain in the individual components of the microstructure. In order, however, that this type of information may be obtained, it is necessary that the experimental studies of anelasticity be interpreted by the appropriate mathematical analysis. This article, therefore, starts with the mathematical formulation of anelasticity.

Jan 1, 1947

By Clarence Zener

It is customary to regard the stress-strain relation as consisting of two parts, thc elastic region and the plastic region. The essential attribute of the plastic region is the presence of a permanent set, which remains upon removal of all stresses. The essential attribute of the elastic region is the absence of such a permanent set. Absence of a permanent set does not imply a linear relation between stress and strain, nor even a single valued relation. In fact, in no real metal is stress a single valued function of strain in the elastic region. The property of a solid in virtue of which stress and strain are not uniquely related in the elastic range will be called "anelasticity." The purpose of the present article is to review and correlate the past work upon the anelasticity of metals. The following paper by W. A. West124 describes investigations upon anelastic properties of iron. Many manifestations of anelasticity have been observed, the first as early as 1835 by Weber.l,2 In his experiments Weber subjected a specimen to a constant load (or deformation) for a given time, and then suddenly removed the load. He observed that most of the deformation suddenly disappeared, but that there remained a residual deformation, which disappeared only gradually with time, as is illustrated in Fig. I. The occurrence of a residual deformation which only gradually disappeared, Weber called the elastic after-effect (Elastische Nackwir-kung). An extensive review of the early work upon elastic after-effects has been given by Auerbach.3 Another manifestation of anelasticity is the dependence of the elastic constants---e.g., Young&apos;s modulus— upon the method of measurement. Thus, if dynamic methods are used, the measured value will depend upon the frequency of oscillation. Still another manifestation is dissipation of energy attending vibration, called damping or internal friction. One objective. of metallurgical science is the understanding of the plastic and fracture properties of metals in terms of their microstructure. Through such an understanding will come the ability to design microstructure to give the desired mechanical properties. A study of anelasticity will furnish an invaluable aid in the attainment of this objective. Such studies, when properly guided, yield information regarding the relation between stress and strain in the individual components of the microstructure. In order, however, that this type of information may be obtained, it is necessary that the experimental studies of anelasticity be interpreted by the appropriate mathematical analysis. This article, therefore, starts with the mathematical formulation of anelasticity.

Jan 1, 1947

By M. C. Udy, C. H. Lorig

THROUGH the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the general effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. LITERATURE Two general factors should he considered in a study of reduction of iron oxide: (1) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe3O4-FeO-H2-H2O, Fe304-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnas1 published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at one temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1942