Search Documents

By Gordon H. Chambers

MANGANESE ore is a true jack-of-all trades among industrial minerals, its only possible rival being iron ore. It is used in porcelain enamel, dry batteries, building brick, glazed pottery, floor tile, plastics, welding rods, chemicals, and varnish. You may be reading this through spectacles decolorized with manganese, and the light bulb above you contains some of this element. GEOLOGY Nearly all commercial manganese oxide deposits are of secondary origin; that is, they are concentrated by weathering from other manganese minerals more sparsely distributed in veins. The oxide minerals usually form irregular masses but in some places (Russia) they occur as beds of varying thickness and purity. Some manganese oxide bodies occur in soft gravel or clay formations but in other places the minerals are found in the form of veins and rounded nodules in limestone and other hard rocks. The geologic features of manganese deposits closely resemble those of iron deposits. Classification of the deposits is shown in the following table: I. Classification of manganese deposits based upon form of occurrence A. Stratiform masses 1. Oxides interlayered with sediments or layered volcanic or metamorphic rocks 2. Carbonates or silicates interlayered with sediments or layered volcanic or metamorphic rocks 3. Oxides, as surface bog deposits B. Veins and breccia filling 1. Oxides in larger part 2. Carbonates or silicates partly weathered to oxides C. Irregular masses 1. Oxides 2. Carbonates or silicates largely weathered to oxides D. Aggregates of small oxides in clay or weathered rocks 1. Mainly oxides E. Unclassified deposits II Classification of manganese deposits based upon mode of origin A. Hydrothermal deposits

Jan 1, 1949

By L. C. Uren, J. Domerco

That the diameter of a well through the oil-producing formation has an important influence on its rate of production is a principle accepted by many petroleum technologists. Knowledge of this principle extends back at least to the time when Slichter and King1 confirmed it in a study of the dynamics of flow of water through porous strata into wells. More recently, the senior author2 and his associates3 have produced qualitative experimental data confirming the principle as applied to drainage of expanding oil and gas mixtures, and suggesting that wells of large diameter, or wells having cavities about them within the reservoir rock, enjoy a material advantage in competition with wells of ordinary diameter. Apparently, however, no one has produced experimental data designed to indicate quantitatively the advantages that wells of large diameter possess in comparison with wells of normal diameter producing under comparable conditions. This paper reviews some preliminary experimental results of this kind, together with some conclusions and speculations based thereon, which further emphasize the importance of well diameter as a factor in determining the efficiency of oil recovery. Theoretical Aspects of Radial Flow of Fluids into Wells It is well understood that in a reservoir rock of uniform thickness and permeability oil and gas flow toward the wells along radial lines. The cross-section of the reservoir rock through which the fluids must move becomes ever smaller as the wall of the well is approached. The velocity of flow must therefore correspondingly increase, an effect that is accentuated by the rapid increase in volume of the fluid due to release

Jan 1, 1935

By J. H. Ffolliott

ALL of the prospects that later became mines in the Ducktown district were discovered prior to 1854, and most of them were exploited before the turn of the century. It is the purpose of this paper to discuss the exploration and current development of the Boyd mine, discovered in 1853. It is in the heart of the Ducktown Basin, in the extreme southeast corner of Tennessee, and is being developed by the Tennessee Copper Co. GEOLOGY The geology of the district has been fully described in many papers. Probably the most complete description is that of Emmons and Laney.I The rocks of the district are considered to be of Lower Cambrian age and are a part of the Great Smoky formation, consisting mainly of interbedded graywacke and mica schist, in which the ore deposits occur. The ore bodies are included in an area of about 6 sq. miles, 2 miles wide and 3 miles long striking N. 45° E., and may be grouped into three general lode systems. The northeast system, including the East Tennessee, London and Burra Burra ore bodies, and the southeast group, comprising the Polk County, Mary and Calloway deposits, are all characterized by relatively high copper values. The ores of the central system, which includes the Eureka, Boyd, Old Tennessee and Cherokee ore bodies, are low in copper and high in total sulphide content. Boyd mine lies roughly halfway between the Old Tennessee and Eureka ore bodies [ ] and 2500 ft. in the hanging wall of the Burra Burra mine (Fig. 1). Elevation of the surface is about 1725 ft. above sea

Jan 1, 1942

By K. Hodgson, N. C. Joughin

The detailed mechanism of rockbursts and other forms of damage due to rock failure in underground mining is as yet unknown. Studies of the energy changes which necessarily occur when an excavation is made underground seem to provide the best understanding of the phenomena leading to rock failure and damage (see Cook 1). It is common knowledge that the damage and rockburst hazard increases with depth and is greatest at remnants and in regions mined in an irregular manner. The rate at which energy is released as an excavation is enlarged provides an objective parameter to describe mining geometry in terms which are significant to studies of rock failure. In this paper, it is shown empirically that the rate of energy release per unit area increase in the size of an excavation is closely related to seismicity and incidence of damage in the mine. Consequently, it is suggested that the energy release rate is an important parameter in the design of underground mine layouts. Observations were made at two mines: the East Rand Proprietary Mines, Ltd. (E.R.P.M.), at a depth of about 9000 ft, and at Harmony Gold Mining Co., Ltd., at a depth of about 5000 ft. At both of these mines continuous recording seismic networks were in operation. (See Cook and Joughin.3) DESCRIPTION At E.R.P.M. the gold-bearing reef dips at approximately 35 degrees and is presently being mined at depths from 8000 ft to 11,000 ft below surface. The rock surrounding the excavation consists of a very homogeneous quartzite extending far into the hangingwall and footwall. The stoping width is approximately 40 in.

Jan 1, 1967

By S. Wiederhorn

The energy and force of interaction between a crack and a slip band have been calculated. When the distance between the crack and the slip band is greater than the dislocation spacing of- the slip band, the force on the cgrack is perpendicular to the slip band. The energy needed to propagate a crack against this force can be lawe enough to pevmit crack propagation parallel to noncleavage planes. SEVERAL recent experiments have demonstrated the occurrence of crack-slip band interaction in ionic crystals having a NaC1-type structure. Stokes, Johnston, and Lil have studied the nucleation and growth of cracks in MgO. From their observations, they conclude that slip bands have the ability to halt and stabilize cleavage crack nuclei. Gilman2 has shown that a crack, propagating along a (100) cleavage plane in a previously deformed LiF crystal, tends, at certain points within the crystal, to switch to (110) planes. He reasons that plastic deformation reduces the cohesive energy of the (110) planes below that of the (1130) planes, making possible (110) crack propagation. Keh3 has demonstrated that when indentations are made in MgO, crkcks form along (110) planes at the indentations. Gilman2 attributes the formation of these cracks to plastic cieformation. There is some doubt as to the formation of cracks on (110) planes. Kuznetsov4 in his discussion of crack propagation in rock salt, shows that splitting along (110) planes requires 1.76 times as much energy as splitting along a stepped (100) surface. Therefore, the observed (110) cracking in LiF and

Jan 1, 1962

By W. H. Forbes

As permissible explosives and electric detonators are now generally recognized as the only safe means of blasting in coal mines, this paper is limited to their use. Causes of Misfires There are many different causes of misfires, but the principal ones are as follows: 1. Explosives which have deteriorated through improper storage either at the storage magazine, the distributing magazine, or at the working face. This is not only true of the explosive itself, but also of its detonating agent. 2. Improper priming and charging at the working face. This commonly occurs when the explosives are handled by inexperienced persons. 3. Improper methods of tamping; the leg wires of the detonator may be abraded or broken by the tamping bar or stick, thereby causing a short or broken circuit. 4. Faulty leading wire, or electrical apparatus of insufficient strength to explode the detonator. Prevention of Misfires Storage is an important factor, especially with permissibles of a nitrate or ammonia base. Both explosives and detonators should be stored in substantially built, fire-resisting magazines and should be situated so that the minimum amount of moisture and heat is present. They should be so constructed that a constant supply of fresh air enters; the floor of the magazine should be raised to permit the circulation of air under the stored explosives. Boxes should be stored top side up and in such a manner that the old explosives are used before those of a later delivery. This eliminates chance of deterioration from lengthy storage. Detonators should be similarly handled and stored. The distributing magazine stock should be regulated so that not more than one day's supply is on hand.

Jan 1, 1930

By Jin Zigang

In China there are more than 30 coal fields menaced by karst-confined water. In the north and east of China there are many collieries which mine coal seams of the Carboniferous and Permian Systems, which are above the Ordovician limestone (general thickness is 500-600 meters). Ordovician limestone is full of karst fissures, contains a lot of water under high pressure (15-65 kg/cm2) near the commercial coal seams (20-80 meters), the water easily infiltrates the thin lime- stone at the point of the structure crevice, so water-irruptions from the floor are the main source of water-related disasters in these coal fields. According to the statistics there were more than 300 accidents of all kinds of water-irruptions from the floor in these fields since the beginning of their development. It is of great significance in developing coal production in the eastern part of China to solve the problem of safe mining of the seams menaced by the karst-confined water of the Ordovician limestone. The research on this subject consists of three parts: (1) investigating the geological structure and hydrogeological conditions of each mine of the mining area; (2) researching the mechanism of water-irruptions from the floor and proposing reliable methods to predict and monitor; (3) improving the mining system and proposing a mining plan with safety precautions against water-caused accidents. The chief task is to research the mechanisms involved and to discover the causes and conditions of the phenomenon. The authors have obtained some findings on this subject in the last five years, making use of the comprehensive observation and research system, which will be discussed under three headings.

Jan 1, 1984

By S. A. Herres, A. R. Elsea

Temper brittleness refers to the loss in the notched-bar impact resistance encountered in most medium- or low-alloy steels when they are tempered within the temperature range of 700 to ll00°F or slowly cooled from a higher tempering temperature. Temper brittleness is important because it impairs the service properties of otherwise suitable steels over the range of hardnesses obtained at medium tempering temperatures and because it is impractical to cool pieces of large section rapidly enough from higher tempering temperatures to prevent temper brittleness. The problem of temper brittleness has always been closely associated with ordnance manufacture because armor plate and gun steels require good shock resistance and are often heat treated in heavy section. However, it is now realized that many brittle failures in structural alloy steel parts are attributable to temper brittleness, and there is little question that it contributes to the low impact resistance of alloy steels used in the hot-rolled or normalized condition which are slowly cooled from the hot-rolling or normalizing temperature. Recently Hollomonl has presented a comprehensive summary of the literature on the subject and an excellent description of the manner in which temper brittleness affects the notched-bar impact resistance and other mechanical properties of steel. Carpenter and Robertson2 have given a good analysis of the probable mechanism of temper brittleness, which is similar in many respects to the precipitation-hardening phenomenon. Fig 1 is their diagram illustrating the response to tempering of a susceptible steel. Three changes are recognized as the temperature of tempering a previously quenched steel is raised: (1) pre- cipitation occurs more rapidly and to a greater extent and the notched-bar impact value falls to a minimum; (2) coalescence of the precipitated particles begins to be effective and the impact values for both rapidly cooled and slowly cooled specimens increase; (3) the precipitate goes back into solution at higher tempering temperatures and the impact values of specimens cooled rapidly enough to retain the solution increase, while reprecipitation occurs in slowly cooled specimens and their impact values decrease again. No change must proceed to completion before the following one begins and there is overlapping in temperature ranges. Although there have been a large number of experimental investigations of temper brittleness, insufficient evidence has been accumulated to permit definite identification of the precipitate wnich causes temper brittleness nor have the specific effects on it of various alloy elements and impurities in steel been definitely established. This lack of evidence is largely a result of the lack of a suitable measure for temper brittleness. Temper brittleness is evidenced by an increase in the temperature of brittle failure of notched-bar impact specimens, but most of the data are in the form of an arbitrary susceptibility ratio of the room-temperature impact value for specimens quenched from a high tempering temper to that of similar specimens furnace cooled from the temper. It is obvious that this numerical ratio is dependent upon the type of specimen used and the specific conditions of testing rather than the characteristics of the steel. In general, manganese, chromium, and nickel alloy steels are most susceptible to temper brittleness and molybdenum has heen used to decrease

Jan 1, 1950

By D. L. Martin

THAT small amounts of impurities have a harm-J- ful effect on the malleability of metals and alloys is well-known. One common type of em-brittlement involves the formation of a small quantity of eutectic at the grain boundaries, and is typified by sulfur embrittlement of nickel. Another example of eutectic embrittlement—sulfur embrittlement of cobalt—is described in this report. In the preparation of specimens for a study of Co-Pt alloys, it was observed that the hot swagabil-ity of the alloys appeared to be influenced by the grade of cobalt used as melting stock. The cause of the hot-shortness was not traced to any particular impurity, although sulfur was suspected.' The damaging action of sulfur on the malleability of cobalt has not been generally recognized,'; in spite of the fact that the Co-S phase diagram8 eveals the same basic conditions—low solubility and eutectic formation—responsible for sulfur embrittlement of iron and nickel.7, 8 Apparently sulfur embrittlement has not been a serious problem in the fabrication of cobalt alloys. One related factor is likely the limited commercial experience with high cobalt alloys, since the predominant use of cobalt has been in alloys containing less than 75 pet Co. A series of Co-S alloys was prepared and studied to establish the effect of sulfur on the hot working characteristics of cobalt. Specimens, 5/8 in. diam by 4 in. long, were prepared by vacuum melting in magnesium oxide crucibles and casting in a copper mold. Two grades of low sulfur electrolytic cobalt were used as the basic material for the study, one from Johnson, Matthey and Co. and the other from the International Nickel Co. Each contained about 99.5 pet Co and had a nominal sulfur content under 0.005 pet. The sulfur was added initially as cobalt sulfide powder. Later, some low sulfur alloys were prepared by diluting the high sulfur alloys with cobalt. Trouble was experienced in controlling the sulfur content. Apparently much of the cobalt sulfide powder was lost during melting, as most of the samples contained a lower sulfur content than was added. The alloys were evaluated for hot brittleness by heating to 1000°C in a hydrogen furnace and swaging in air. The results of these tests are summarized in Table I. All the alloys containing less than 0.008 pet S were successfully hot swaged to 1/4 in. diam. The bars containing more than 0.015 pet S could not be swaged because of the formation of intercrystal-line cracks similar to those illustrated in Fig. 1. Examination of the microstructure of the cast bars revealed cobalt sulfide eutectic at the grain boundaries, Fig. 2. The sulfide was not always continuous at grain boundaries in bars that were hot embrittled but, in general, the particles did form a network that could account for the brittleness above the eutectic temperature, 880°C. There is no question about the brittle nature of a specimen exhibiting a continuous sulfide network such as is shown in Fig. 2b, though a sulfide distribution similar to that in Fig. 2a is marginal. This particular bar cracked when hot-swaged. However, other bars with lower sulfur content but with some sulfide phase at grain boundaries were successfully worked. The reduction of area of a hot tensile test specimen was also found to be a sensitive indicator of sulfur embrittlement. The variation of reduction of area with sulfur content is shown in Fig. 3 for specimens fractured at 900°C in an evacuated capsule. The ductility of cobalt is greatly reduced when the sulfur content exceeds 0.005 pet. Similar results were obtained for alloys tested at 800°C, below the eutectic temperature. The upper sulfur embrittlement limit of 0.015 pet, Table I, agrees with the observation of Kalmus8 hat

Jan 1, 1957

By C. H. Li, S. H. Bendel, J. A. Sartell

Small additions of Mg to a 62 Cu-38 Ni alloy reduce the oxidation yates drastically between 500° and 850°C. Metallographic examination of the oxide scale disclosed a continuous network, identified by X-ray diffraction as (Ni, Mg)O solid solutions, located along the former alloy grain boundaries. This network acts as a barrier to diffusion. It is thought to result from the segregation of mg to the alloy grain boundaries. Oxidation occurs preferentially in these regions because of the presence of this more active element. To substantiate these ideas, homogenized alloys ulere oxidized. No oxide network was produced and oxidation rates were the same as for the parent 62 Cu-38 Ni alloy. An interesting aspect of the oxidation of the 62 Cu-38 Ni alloy previously described by the present authors, is the relationship between oxidation kinetics and changes in the microstructure of the oxide.' The oxide scale on these alloys consists of two layers: a thin layer of CuO outside a much thicker layer of Cu20 in which particles of NiO are dispersed. In addition, immediately beneath the oxide-metal interface there is an internally oxidized zone in which NiO particles are dispersed in a copper-rich alloy matrix. Experimental observations on the growth of the individual layers under isothermal conditions have led to the conclusion that the rate-determining step in the oxidation of this alloy is the diffusion of anions through the Cu20 layer. It has been found that this diffusion rate is increased by the recrystallization of the outer CuO layer. Willardson and Gorton have reported that the addition of magnesium to the 62 Cu-38 Ni alloy causes a decrease in the oxidation rate.2 The present investigation was undertaken in order to determine the mechanism by which magnesium additions improve the oxidation resistance of the 62 Cu-38 Ni alloy. EXPERIMENTAL PROCEDURE Fifty-gram ingots of Cu-Ni alloys were prepared by vacuum melting materials of 99.999+ pct purity. These ingots were then remelted in a He atmos- phere and magnesium added in the form of a previously prepared and analyzed Cu-Mg master alloy. This procedure was necessitated by the high reactivity of pure magnesium at high temperatures. The proportion of the alloying elements was adjusted so as to obtain alloys with the desired magnesium content while maintaining a Cu-Ni ratio of 62 :38 by weight. (All alloy compositions will be given in weight percent.) Since it was considered desirable to study the oxidation of only single-phase, solid-solution alloys, it was necessary first to determine the approximate limit of solid solubility of magnesium in the 62 Cu-38 Ni alloy. A series of melts with various magnesium contents was made, homogenized by annealing for 48 hr at 975OC, then cooled in the furnace. Metallographic samples were prepared, etched in a potassium dichromate solution and examined at XI500 for the presence of a second phase. The alloys were then chemically analyzed and it was found that the approximate limit of solid solubility of magnesium in the 62 Cu-38 Ni alloy was 1 pct Mg. The ingots containing less than 1 pct Mg (0.19, 0.29, 0.58, and 0.87 pct Mg) were cold-rolled down to thicknesses suitable for oxidation experiments and specimens for gravimetric studies were cut to dimensions of 3.0 by 1.5 by 0.05 cm, specimens for inert marker studies, 0.6 by 0.6 by 0.17 cm. These were heat-treated in a protective atmosphere at a temperature (975" C) well above the oxidation temperatures and furnace-cooled to insure structural stability of the alloy during oxidation. Immediately prior to oxidation, the specimens were chemically cleaned by immersion for 1 min in a solution of 2 parts nitric acid, 1 part acetic

Jan 1, 1961

By F. E. Calkins

THE following presentation of the more important accumulated facts and probabilities involved in copper ore deposition is based on my experience in examination work and study of the extensive litera-ture of the subject; to make personal mention of all sources of information would require the naming of a small army of able geologists and other investigators who have contributed to, building up the science. I have tried to present the salient features of the subject in logical order and condensed form, and to point out the relative importance of processes involved. Doubt-less many geologists could suggest some changes and many additions. ORIGINAL SOURCE The original source of all copper was in the earth's interior; it has been brought to the outer part of the earth, within reach of man, in three ways: (1) By intrusions and flows of basic igneous rocks containing copper in minute quantities, presumably as silicate or sulfide. No orebodies have been formed by this method. (2) As segregations within intrusive igneous rocks, the copper minerals having solidified at the same time as the rock itself. The few deposits known to have been formed in this manner have been of little or no importance. The oft quoted Sudbury nickel-copper deposits are now known to belong to the class following. (3) By gaseous or liquid aqueous emanations from ,large deep-seated masses of intrusive molten rock. These emanations, or mineral solutions, ascended through zones of connected openings in the earth's crust and dropped their load at points far above their source. Deposits formed in this manner were the primary source of nearly all, if not all, of the world's copper production.

Jan 10, 1923

By I. N. Zavarine

THE present paper is a continuation of the work on the relationship between the magnetic and the phase transformations in carbon steels during quenching. An account was given by the author in a previous paper1 of an investigation of this relationship during a continuous quench. The experimental difficulties then encountered prevented a conclusive proof of the existence or absence of such a relationship. The conclusions of the previous paper were derived indirectly. The present paper deals with the same problem, but the method of attack is modified. The technique developed by Davenport and Bain2 in their well-known study of austenite transformation at subcritical temperature was adopted in the present investigation.. They have shown that the austenite to martensite transformation can be caused to proceed at a relatively slow rate by quenching steels into a hot metal bath. Slowing down of the rate of transformation, together with an observation by Lewis3 that a eutectoid steel can be preserved in the nonmagnetic state by such quenching, pointed out a possibility of a study of both transformations .under more favorable conditions than previously described. The preliminary steps were connected with the technique of the hot bath quench. To study this phase of the present work a modification of the apparatus previously described1 was used. The modification consisted in the use of a hot quenching bath instead of brine, and in fixing the secondary and the primary coils of the apparatus in a stationary position in and around the bath. Tubular specimens, as in the previous investigation, were heated in a suitable furnace to a temperature in the austenitic

Jan 1, 1935

By J. H. Bowden

The shaft-plant here described was put in operation in September, 1895, and the No. 6 slope-motor was started in May, 1896. The plant comprises : One Norwalk three-stage compressor l21/2, 91/2 and 5 in. diameters of air- and 20 in. diameter of steam-cylinder, all 24 in. stroke; capacity at 100 revolutions, 296 cu. ft. of free air per minute, compressed to 600 Ibs. per sq. in. A main pipe, 5 in. diameter, 4380 ft. long, with five charging-stations in No. 6 Shaft, and a branch of 3 in. pipe, 3100 ft. long, with three charging stations, in No. 6 Slope. These pipes on each line charge a Porter compressed-air motor, with 7 by 14 in. cylinders, and four 24 in. drivers, weighing about eight tons, with a tank-capacity of 130 cu. ft. of air at 550 lbs. pressure in the main tank, reduced to 160 lbs. in the 8-in. auxiliary tank of 4.2 cu. ft. capacity, supplying the cylinders. The No. 6 shaft run averages 4000 ft. each way on grades of $ to 23/4 per cent., and averaging close to one per cent. in favor of the loaded cars. The No. 6 slope run averages 2100 ft. with nearly the same grades. The mine-cars weigh 2800 Ibs. empty, and about 9800 lbs. loaded, and are hauled in trips of 12 to 20, averaging about 15 cars. The shaft-motor now hauls about 355, and the slope-motor 320 cars per day of 10 hours, replacing in the shaft 17 mules, and

Jan 1, 1901

By T. J. Whalen and Michael

The grain shape of the carbide in nickel-bowled ad cobalt-bonded titanium carbides was studied by microgiaphic examination, and the influcence of sintering atmosphere, sintering substl-after, ami the amount of metal binder on the grain shape was determined. If was found that the Carbide grain cross sections in the nickel and cobalt cermets ranged from round to angular, depending on the sintering conditions. The spheroidization of the carbides in both cobalt-bonded and nickel-bonded titanium carbides may be attribicted to oxygen. In the course of studies on titanium-carbide base cermets, various investigators have reported on the shape of the carbide grains, and it was noticed that grain shapes were obtained which were either spheroids, or polygons with rounded or square edges. It was also noted that the shapes of the carbide grains changed with time or composition. skolnickl showed that the titanium-carbide grains. after infiltration in vacuum with nickel tended to spheroi- dize with time. The titanium-carbide skeleton was located on a beryllia plate during infiltration. Gur-land,' who studied the microstructure of titanium carbide-cobalt compacts, showed that the carbide grains are round after 1 hr at 1450oC in a hydrogen atmosphere and angular after 7 hr at the same temperature. Goetzel3 has found that the carbide grains in compacts with a high binder content. 40 to 60 pet. tend to be spheroidized. whereas Blumenthal and silverman4 pointed out that the higher binder contents could yield either round or rectangular grains with rounded edges. depending on the nature of the binder. It is the purpose of this paper to present experi-

Jan 1, 1961

By AIME AIME

AMONG the members of the Institute there are thirty-three who have been members for a half- century or-more Some time ago a professor of psychology made a careful study of a group of unusually brilliant children to determine whether there was any truth in the general belief that a brilliant mind is usually to be found in a physically sub-normal body. He definitely proved the exact opposite and it is now known that children who are above the average in mental capacity are also above the average in physical health and strength.

Jan 1, 1929

By J. Skrove, C. R. Boardman

In situ permeability of the rock outside the Hardhat chimney was determined by pressurization of long holes with air. Experimental data indicated a remarkable difference between fracture permeability of the rock near the chimney and that at a considerable distance. Although permeable fault zones were known to exist in the granite stock, the measurements of background permeability were quite low, on the order of tenths to several millidarcies. The observed difference is about two or three orders of magnitude above this background in the region 125 to 215 ft radially from the shot point, or 80 to 165 ft radially from the vertical axis of the chimney. The presence of a collapsed drift immediately beyond this region precluded measurements which could have defined the maximum extent of the zone of high permeabilily. INTRODUCTION Previous exploration has revealed that contained nu-clear explosions create cavities which generally collapse, resulting in rubble-filled chimneys and annular fractured zones. These geometries have been shown to result in complex flow regimes which should increase the production rate from hydrocarbon reservoirs.' Empirical scaling equations have been developed for estimatina chimney radii and heights for a variet; of rock media.' The exten; of the annular fractured zone has been documented and associated permeability changes have been observed qualitatively for several explosions. This study was begun to establish the nature and magnitude of the permeability of the latter region. It is anticipated that results will be useful in estimating permeability changes and consequent production stimulation which might ensue from a contained explosion in a hydrocarbon reservoir. The post-shot environment of the Hardhat event (a 5-kt contained nuclear explosion in granitic rock) was c'hosen for the experimental measurements. The Hardhat device was detonated at a depth of 939 ft, and subsequent exploration revealed a chimney of broken rock with a radius of 65 to 70 ft and a height above shot point of 281 ft.' BeFore the explosion, the Hardhat medium was highly jointed and fractured (Fig. I). Jt was expected that differential rock motion along these and other weaknesses induced during cavity growth and collapse would significantly alter the permeability of the rock mass. EXPERIMENTAL METHOD Initially, three 2-in. diameter holes (Nos. 10, 12 and 19) were drilled about 25 ft outward through the walls of the 500-ft level drift (elevation 4,253 ft, Fig. 2). One was drilled near the chimney and two holes, one vertical and the other horizontal, were drilled near the shaft. Order-of-magnitude differences in permeability obtained by pressurization measurements indicated further: investigation was warranted. A series of 3-in. diameter holes was then drilled with water as a coolant into the walls and roof of the drift (Fig. 2). An 11-in. long packer was set from 1 to 8 Et inside each hole and air was injected at measured Row rates. Hole pressures were monitored at the collar. Permeability was low enough in the holes near the access shaft that pressure could be maintained long enough to obtain good pressure decay rates. In the vicinity of the chimney, however, permeability was so high that this was not possible and air was injected under steady-state conditions. About one year later, these same holes were retested to

Jan 1, 1967

By M. H. Pilkuhn, H. Rupprecht

The junction luminescence of GaAsxP1-x diodes containing up to 47 pct Gap was studied. Diodes were prepared by diffusing zinc into n-type material which was eithw boat- or vapor-gvown. Observations concerning the energy and the line shape of the spontaneous emission are presented and discussed; in particular the influence of inhomogeneous phosphorus distribution is considered. The role of reabsorption of the junction radiation is pointed out. With increasing current, the peak emission shifts to higher enwgy. This is alm true in cases where slow line narrowing occurs simultaneously. The length dependence of the threshold current density for lasing at 77 °K was examined for lasers made from the same material. It was found that longer lasers have lower threshold curvent densities, Estimates of the characteristic laser losses are given. Data concwning the range of Gap concentration in which stimulated emission was observed are presented. FORWARD-BIASED p-n junctions in mixed alloys of GaAsxPl-, emit light whose wave length depenfs on the composition of the alloy ranging from 8400A (x = 1) to 5350A (x = 0) at 77°K. Laser action in vapor-grown material was first reported by Holonyak and evacqua,' and in boat-grown material by Ainslie, Pilkuhn, and Rupprecht.' In both cases this was observed for low Gap concentration where GaAs,Pl-, is still a "direct" semiconductor with the lowest conductance-band minimum at k = 0 and a subsidiary minimum in the [loo] direction. As the Gap concentration is increased, the subsidiary [loo] minimum in the conduction band is lowered and finally becomes the lowest minimum for Gap concentrations above 50 pt,3 making the alloy an ''indirect" semiconductor. It is of interest to determine up to which Gap concentration stimulated emission can be observed. EXPERIMENTAL Boat-grown material was prepared by N. Ainslie of IBM by horizontal Bridgman technique. The material was n type and silicon-doped up to a concentration of 10'' cm-'. Vapor-grown material was made by E. Hull of IBM or received from Merck & Co. Diodes were fabricated in a similar manner as in the case of GaAs by zinc diffusion. Details about the diffusion can be found in a later paper.4 All diodes were of Fabry-Perot structure with two parallel sides cleaved and the other two sides sawed. Their width ranged from 50 to 150 p and their length from 50 to 700 p. RESULTS AND DISCUSSION Spectral Distributions. A typical display of the junction luminescence of a GaAsxPl-, diode is shown in Fig. 1. The liquid-nitrogen and room-temperature curves which were taken at a very low current (25 ma dc) show a relatively sharp high-energy emission which is band-edge radiation. They also show a broad low-energy emission which is due to transitions to deep impurity levels. This latter emission line may have different shapes and positions depending on the nature of the material. It can sometimes be quite near the band gap giving rise to "bumps" in the high-energy line. The results presented in this paper will be concerned only with the high-energy emission which becomes more intense relative to the low-energy emission when the current is increased and the temperature is lowered.

Jan 1, 1964

By H. J. Beach

This paper describes the properties and uses of cementitious mixtures containing 10 to 20 per cent bentonite and 2 per cent or more sodium chloride. Salt additions improve bentonite cement by increasing early strength and stabilizing viscosity without changing thickening time. The volume yield of cement is increased 20 per cent or more without lowered early strength. The unique properties of salt in this type of system make savings of more than 10 per cent possible where light-weight, low-strength cementitious material is adequate to fill behind pipe. The density range of these mixtures is 12 to 13 1b/gal and the filtration rates are medium-low, aiding the placement of long columns in primary cementing. Where available, sea water is an ideal salt source in preparing these slurries. INTRODUCTION Accelerators increase the rate of cement hydration. In speeding reaction with water, they can affect cement performance by reducing thickening time and increasing early strength after set. Accelerators that cause both effects can be considered "total", and those which produce only one effect can be called "partial". Materials that act conversely to accelerators are retarders. and they also can be total or partial. Partial retarders. make high-temperature cementing possible by prolonging thickening time while impairing early strength only slightly. Most known accelerators are total. A useful partial accelerator would increase strength without altering thickening time. This report concerns material combinations in which a normally total accelerator exerts unique partial properties. Utilizing these limited effects improves bentonite cement. SEPARATE EFFECTS OF SODIUM CHLORIDE AND BENTONITE ON CEMENT Sodium chloride and calcium chloride are commonly used in cement, and at low concentrations their effects are similar. Ludwig1 studied sodium chloride in API Class A and Class E cements.' Figs. 1 and 2 sum- marize his data taken at 140°F on slurry pumpability and early strength. Normal water-to-cement ratios are 0.46 and 0.40, respectively, for Class A and Class E cements. At saturation the salt content is 12 to 14 per cent of the weight of cement solids. The illustrations, therefore, cover the range of salt solubility in the mixing water. The data show that sodium chloride is a total accelerator of the Class E cement studied over the range of solubility. It is total in Class A cement to 6 per cent. Above this concentration salt becomes a retarder— partial from 6 to 10 per cent and total above. These results are general for different brands of Class A cement, although the shift from acceleration to retardation may occur at different salt concentrations for different temperatures. The results are specific for the Class E brand studied. In discussing his data, the investigator emphasized that different Class E cements might respond erratically to salt, depending on the brand chosen. Morgan and Dumbauld3 escribe the properties of bentonite cement in a paper that is a standard reference in using these systems. Bentonite functions in cement as an enabling agent; each bentonite addition equal to 1 per cent of the weight of dry cement makes possible the further addition of 4.5 per cent water.' Thus, 10 per cent bentonite in Class A cement, normally slurried neat with 46 per cent water, enables the slurry to contain another 45 per cent before settling. Water is one of the lightest and cheapest cement extenders; it reduces density and cost. Bentonite cements produce uniform slurries having low susceptibility to solids separation. After set, they offer low resistance to perforation.

BULLETIN 177. The decline and ultimate production of oil wells with notes on the valuation of oil properties, by C. H.- Beal. 1919. 84 pp., 4pls., 80 figs. BULLETIN 179. Abstracts of current decisions on mines and mining, reported from September to December, 1918, by J. W. Thompson. 1919. 166 pp. TECHNICAL PAPER 214. Motor gasoline; properties, laboratory methods of testing, and practical specifications, by E. W. Dean. 1919. 33 pp., 2 figs. TECHNICAL PAPER 219. Combustion and flue-gas analysis, by U. S. Fuel Administration. 1919. 12 pp., 5 figs. TECHNICAL PAPER 223. Cost-keeping for small metal mines, by J. C. Pickering. 1919. 46 pp. Only a limited supply of these publications is available for free distribution. Publications should be ordered by number and title. Applications should be addressed to the Director of the Bureau of Mines, Washington, D. C.

Jan 7, 1919

By L. C. Armstrong

Twice in the past two years and in two widely separated localities—ane near Williamsville, Mo., and the other in the Allard Lake district of Quebec— the Contract Drilling Division of the Longyear Company has experienced perplexing difficulties in drilling granitoid igneous rocks. The rocks in both places are characterized by appreciable amounts of feldspar intimately inter-grown with quartz particles of microscopic dimensions. The disappointingly slow rate of advance and the exceptionally high bortz loss, obtaining during the life of these two projects, are ascribed largely to the resistance to abrasion of these two minerals when arranged in this intergrown pattern. Whether all intergrowth-bearing igneous rocks would offer extraordinary resistance to bit progress cannot be stated with assurance on the strength of these experiences alone. More data on diamond drilling this sort of material in a number of localities are needed before any generalizations can be made safely. It should be pointed out that the lack of time and funds made it impossible for the writer, or other persons interested in correlating the details of bit histories with the kinds of rocks drilled, to be present during the performance of the contracts. However, the records kept in the normal course of drilling are deemed complete enough to be reportworthy. This information is presented here together with the findings made in studies of the rocks involved, with the thought that it may attract the comments of others who may have encountered similar refractory drilling conditions. A pooling of knowledge on the problem would be of material aid in devising more efficient cutting tools and procedures for penetrating this kind of rock. Drilling Blastholes in the Williamsville Granite Due to the unsatisfactory perform- ance of pneumatic percussion drills in boring blastholes on a construction contract near Williamsville, Mo., tests were made with a diamond drill. The poor progress achieved and the excessive loss of diamonds, however, soon led to the abandonment of these trials. The diamonds, in all of the bits tried, lost their cutting edges and acquired a polish after being in service for distances ranging from a few inches to a few feet. Coring bits containing surface-set, whole-stone bortz in a tungsten powder matrix were employed. The cost assignable to bortz wear averaged $7.17 per foot. This item of expense is several times the amount normally expended in diamond drilling in firm, unfractured, granitic rocks. Diamond-impregnated, tungsten carbide bits also were used without success. The diamond wear was at the rate of $0.98 per foot, but the diamond chips became too polished for further duty in less than a foot of drilling. The Williamsville granite is pink and medium-grained. In the hand specimen, it has a fresh, sound appearance; it is seemingly composed almost entirely of interlocking grains of feldspar and quartz and has no discernible features suggesting a greater durability than is usually found in rocks with this composition and texture. Microscopic examination, however, reveals a predominance of feldspar grains with more or less regularly distributed and sharply angular masses of quartz (see Fig 1). The pattern assumed by the two minerals in this mode of occurrence is referred to as a "graphic intergrowth," as it bears some resemblance to the cuneiform characters of ancient Persian writing. The other principal constituents are quartz-free feldspars (microcline and orthoclase) and quartz. All of these constituents are in nearly equidimensional grains, ranging up to about 3 mm in length. There are also

Jan 1, 1950